Maytag washer manufacture changes are not worth a dime. I suspect EPA made the changes, and engineering was made by someone that has never washed a load of clothes in the entire life. There is no agitator and/or supposedly made to conserve water. Well, it saves water alright with each load. There will be a 2 foot circle in the middle of a bed sheet that doesnt get wet; the same with a sweaters. I have checked with different stores and all made the same. And heaven forbid if you dropped a sock and wanted to add it to the load with the mate. The lid locks. I am both angry and dissatisfied and will tell this same story to anyone wanting to purchase a washing machine.

Well Maytag, I have to say that I am very disappointed with your washer. When I put it on the bedding setting and try to wash a big load, it barely moves the load around. If you have a regular agitator to replace this useless one that is in this new washer I would like to have one. My laundry is barely getting washed and when you look inside the washer everything that is on the top stays on the top, not like the older washers where you could see that the laundry was getting sucked down with the proper agitator.

Ice builds bottom of freezer then leaks onto floor. Should be a recall.

I purchased and installed a high end MAYTAG above the stove microwave. After 3 years of light use I hear an electric cracking sound and it dies. Of course no warranty coverage. Model MMV5208WB-1. I have to conclude MAYTAG builds junk and does not stand behind what they sell.

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

Please let me know if there is a class action suit. This refrigerator leaks water all my floor every three days or so. I have to chip the ice off the bottom of freezer every three or four days. Storage is also a joke. Poor design.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

I purchased the Maytag Bravos 400 series top load washer about 4 years ago. Paid over $1000 for it, on sale. Its bearings started grinding within four years and the seal is gone which has resulted in water leaking out through the bottom of the machine. VERY expensive to repair and ultimately not worth it. Pretty disappointed that Maytag products reliable for such a short period of time and must then be kicked to the curb. NOT a quality product.

This is a Maytag Neptune MAH8700AWW. This machine has been repaired a couple of times already and it has a will of its own. When it goes into that fast spin cycle that will kicks in and it starts moving. I wonder if someday its going to attack me. So, last Friday night we put a load in and it went into that fast spin cycle. It was making a noise like an elephant in labor so I looked in the laundry room.... Clouds of smoke were billowing out of the top of the machine. Our house will filling up with washing machine smoke! My husband stopped it, but I think it was a gnats hair close to bursting into flames. He looked into the front of the machine when the smoke dissipated and the entire gasket was in shreds. No more Maytag. Never. Im done.

Shortly after purchasing my Maytag refrigerator had to pay for a new motor in the ice maker. The cover for the lower large food tray broke. Now approx. 4 years later am getting ice build-up on the bottom of the lower freezer unit, about one-half inch thick. It is enough so the freezer door wont seal when it closes and the inside builds up with frost. Not happy with Maytag or this refrigerator.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

This Maytag Centennial is the WORST piece of junk I ever purchased and I received the same uninterested response from Maytag as everyone else. Maytag sent a service man out who said it was functioning as it was intended. Once started, this washing machine cant stop if you forget to add an item. It dumps out all the water and starts the hour-long cycle over. All settings are an hour-long cycle. Unless Bulky or Delicate is selected you only get 2 inches of water -- Even for Heavy Duty. No matter what the setting, the clothes do not come out clean. You must hand wash them first. Maytags are no longer a desired product.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

We purchased a Maytag Centennial washing machine from a local business here in Knoxville in 2013. My previous Maytag lasted seven+ years and I was very happy with it. It began to leak water and after two times of having water on the floor, we decided it had worn out and purchased another washer. We immediately wanted another Maytag since our previous one has lasted for quite a while. We bought the new Maytag Centennial washing machine in the Spring of 2011. This is May of 2013 and we have had to purchase another washing machine since the electrical board in ours went out. The replacement part is listed at $300+ and that is without labor to install. Needless to say, I am very unhappy that I have had to purchase another washer so soon... and did not buy a Maytag this time.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

Washer gets out off balance too easily. If I put in a couple of towels, it will almost invariably stop part way through the wash cycle. I was told you have a great washer! Its the last of the two-belt Maytags! My reaction: so what?

I purchased 4 new Maytag appliances as part of a kitchen update. The dishwasher was the first to fail, less than a year after being installed. The control panel stopped working (random lights would come on, always different from the one being pressed, and frequently incompatible selections such as Rinse Only and Sanitize. PC Richards sent a repairman with a new part, no charge. A few weeks ago, it happened again. PC Richards says that replacement parts are only under warranty for 90 days, so now the repair is on me. I could pay or repair it myself or pay PC Richards to do it. Thank goodness I am handy, but I still have to pay for the part. Now I am reading that the MDB7749 series has a history of this problem. When is Maytag going to own up and issue free repairs? I certainly will never buy Maytag again, as both the range and the refrigerator also have common problems. Luckily, I paid for the 10-year service agreement on those appliances.

I am also frustrated with Maytag for the same exact problem... The control panel and the dishwasher not working just after our year warranty went out. I purchased this product because we had a good experience with a Maytag Dishwasher lasting about 20 years, only to get fooled that the quality is not there any longer. This seems like BAD business on Maytag, Whirlpool, and Home Depot! How can we get an official complaint to someone who can fix this? Another example of big businesses that do not care to take care of customers! Why would a company like Home Depot continue to support this business!!

I love the bottom freezer & refrigerator on top. Its so convenient... but it really could have a little more refrigerator space though. I love the stainless steel. It makes the fridge look regal. Also, the fingerprints do not show.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

Had this model MDB7749SBM1 for almost 3 years and paid over $700 for it. Thought I was purchasing a good machines. The last few months the control panel pops out and away from the front door panel. Do get it back. You have to unscrew the panel from the door. Inside is all plastic and broken. How can it be broken when it is an area never touched. Every time you open the door after a wash it pops out again. To get it repaired will cost too much. It is a badly designed unit which should have a latch instead of just pulling out.I am so disappointed and will think twice before buying Maytag. I have never had luck with any Maytag dishwasher lasting. At this point I dont know whether to just buy another brand or glue it. We are not keeping our home so I dont want to invest money. Awful machine and I see it is discontinued so there are a lot of complaints. Thanks for sticking us Maytag.

The Maytag Neptune FAV6800AWW Washer has to be the crappiest product I have ever bought. I bought it brand new and hardly ever used it. The first time it broke it was luckily under warranty, although we had to pay for the repair man to install it. It took two new circuit boards before it was fixed. A few months later, the circuit board went again, and it was conveniently for Maytag now out of warranty. The repair man told us that their company never carried these washers because from the get go they had a ton of problems. He said that the odds of it breaking again were great and that we would be better off putting the money into a new washer.I dont understand how the company, in good conscience, could continue to sell a product to consumers that they knew was faulty. It was not a cheap washer and I have never been so disappointed in my life. You would think they would have had a mass recall or, knowing how many problems consumers were having with the product, offer so much money towards a new one.I laugh at the commercials where the Maytag man was bored because their product never broke I could have kept that man busy for months!

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

First the dishwasher - Control board no longer works. Seen many people with same problem. Dishwasher sitting there useless since cant afford to replace. Will cost as much as the purchase. Stove has defect between glass on oven door. Aqua clean feature is a farce and I feel vent at bottom of oven is asking for a disaster if any grease should spill in there. Maytag will not honor or admit any defects.

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

3 years into the buying of a Maytag Bravos XL MCT washing machine (Serial # **) and already had to replace the original control panel for a cost of $400+ in less than 2 years of the buy. Now AGAIN the replaced control panel is now once again shot and the machine is not starting. The appliance needs to have a #manufacturers recall for the control panel. #Maytag #Whirpool #BetterBusinessBureau Note -- all existing customers, please lodge manufacturers complaint for the control panel issues @ 1-800-344-1274. (Even if you dont pay because of extended warranty or plan coverage, if you are facing the control panel issue year on year). All future customers, buy this appliance at your own risk.

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

Our current dishwasher was already installed when we purchased this house. It is adequate, however, it does not do a great job with caked-on food. This means that the worst dishes need to be pre-cleaned.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

We purchased a Maytag dryer in Dec 2012 and several days ago the heating unit failed (mid April 2014). I did a quick search on this site and a few others where I saw numerous such issues with Maytag dryers. I realized that I was 4 months beyond the warranty period but took a shot at calling their customer service line to voice my displeasure only to get the company line that they could do nothing. My wife and I have been married 27 years this year and this was the 4th dryer we have purchased (1st and last Maytag) which obviously did not last like the other brands or like we expected. I definitely do not recommend this brand!

After 18 months of use Our Maytag Dishwasher (MDB7749) has the same control panel problem as a lot of other user complaints. I wish I too had read the consumer reviews before my purchase. We will never buy another Whirlpool product!!

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

I purchased a dryer model med7500yw not even a year ago and the heating element has failed four times causing a lint fire and my clothes are burned and melted. Maytag only wants to keep servicing the dryer and not refund me my money. I asked the representative who claimed to be a supervisor would she feel safe with the dryer in her home and her rude remark was this is not about me and because the service was done back in November and now its January it will need to be serviced yet again. I am losing time from work and the repair men are rude and ignorant.

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

I bought my Maytag Refrigerator about 7 years ago and the night mares have not stopped. The ice maker has broken down so many times, I forgot to count. The drip from the ice maker lands on the floor of the freezer and drips out to the floor. The cold part of refrigerator end up freezing the fruits and veggie and milk.

My washer is great. It get the job done. Have no agitator so I can wash 2 comforters. I really like Maytag Heavy Duty. Can get the job done right the first time. Self clean itself also. Also it is a efficiency.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

The Maytag Bravo Washing Machine was sold as the top of the line. In reality it is very difficult to work with for three specific reasons. First, the spin speed is too high causing the clothes to be wound into tight balls causing pilling and the need to iron everything from t-shirts to workout pants. Second, the spin speed is so high that you can only put a few towels in the washer at a time or the machine goes off kilter several times a cycle. Finally, if you lower the spin speed the items take forever to dry. I used this for less than 30 days and tried to return it but Maytag would not take it back. The only cycle type I can use is the rapid wash unless I want to spend all day washing and drying one load. I hate this washer more than I can describe and will NEVER purchase another Maytag product. It absolutely ruins your clothes and Maytag takes no responsibility for making a very bad product.

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.

I bought a new Maytag washer 1 year ago. It does not do a good job of washing the clothes. I have tried to contact customer service but what a waste of time that has been. I would never buy another MAYTAG washer again. This is after owning an older style Maytag for 25 years that I never had one problem with until it wore out. They are now junk. I bought at Leons. Would be very careful of buying there again as they were also no help with this washer not working properly.

Bought Bravos XL washer/dryer from Home Depot in November 2014; installed 12/8/14. First repair was in March 2015! Clean machine cycle quit working properly on 3rd attempt. Bearings were replaced, tub was replaced and main board was replaced all before May 2015. Wash load constantly becomes unbalanced if more than 3 bath towels are in the load or more than 2 pairs of jeans. Can not start a load of wash and leave home because the machine will start bouncing and rocking when unbalanced and will shut down after it tries to self-balance 3 times. You end up with a load of twisted up, totally wet mangled clothes. Maytag refused to replace the machine and Home Depot continues to sell this junk to unsuspecting buyers. Wish I had looked at reviews before I bought this model. Worst $1,200 Ive ever spent. I have always bought Maytag appliances--refrig, stove, dishwasher, microwave, other washers--but Maytag has lost me as a customer after this experience with them. Terrible design and poor customer service for not standing behind their products.

I love my washer. I have had it for 13 yrs and has only needed repair once. My complaint is the gasket on the tub has black mold that grows on it. I have cleaned it with bleach, bathroom cleaner, alcohol, but it always comes back. What can I do to prevent illness from mold?

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

I spoke with Mike today at the customer service department at Maytag to see if Maytag would pay for the parts to repair my 04/2010 Maytag front load washer (model MHWE450WW00). The bearing assembly needs to be replaced. So, that means the tub and basket need to be replaced too. The original cost in 04/2010 was $1,088 plus tax. The cost to repair is $1,048. Maytag will do nothing since it was purchased over 12 months ago. I cant believe I just threw almost $1100 away on a washer. Obviously, there is something wrong when an appliance doesnt work after 1.5 years.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

We purchased a front-load Maytag washing machine (Model MHW3505FW1) two years ago this month. When the machine is empty, we always leave to door open. We dont allow clothes to stay in it for long, never for more than a day (the load is usually changed as soon as the cycle is over). Right now, the rubber seal on the front has tons of black mold on it, and when I lift the seal to look underneath, its way worse. There have been many problems like this reported on front-loaders. Wish Id known! Maytag will not send a replacement seal.

I purchased the Bravos Washer and Dryer from an elderly couple who didnt have it more than 6 months. About a year went by and the washer started making a noise when the water extracted and finally flooded my laundry room. I found that a penny had gotten into the plastic housing that extracts the water. This has happened on 2 different occasions. I have replaced the extraction unit 2 times and it now cracked again. Then I started getting F1 error codes and having to restart as much as 6 times so it would start the cycle. This washer has been a royal pain. It is frustrating when you think you are getting a quality product and have nothing but problems. I previously had a Kenmore washer and dryer that lasted me 15 years and was still functioning when we sold the set after buying the Maytag Monster. We only ever replaced the heating element in the dryer once. That was it. I will not consider a Maytag again and possibly not another HE at all. Glad I did not buy them new!

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

I purchased a Maytag Microwave Oven MMV5208 WS 1 from Home Depot less than two years ago. Mine was actually manufactured in April 2013 according to the ID tag. A couple of months ago it started acting up because a switch when the door closes began to malfunction and you had to open and close the door several times to get the microwave started. Then all of a sudden when you set the timer and pushed the start button it would flash on and immediately shut off. This is extremely frustrating because I paid more than $400.00 and purchased it less than two years ago. I am disappointed because Maytag advertises its reliability and this microwave is anything but reliable.

Bought a Maytag Front Load MHW6000AW washer and had a problem with amount of water in wash cycle. Dealer sent service men 3 times and changed several parts but washer still did not work and both repairmen said they did not know what was wrong. They called Maytag Tech Support but those people did not listen and said if no code shows up the machine is operating properly. Maytag then sent another company repairman. He worked 2 hours and said he could not find the trouble and Maytag support hung up on him. Maytag then sent another company repairman and he did one test and said the machine is fine and left in about 15 minutes total time. Now Maytag refuses to send another company for another opinion but I have a $1200 machine that still does not work properly. I am totally dissatisfied with Maytag and will stay away from their products totally. Companies wonder why people buy foreign equipment and this is the answer. I had a Samsung washer and never had one bit of trouble with it.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

Prior to purchase, I did my due diligence and read reviews about this washing machine. Apparently, they were written by Maytag employees, because this washing machine has been a major disappointment. Yes, it tangles clothes and sheets, but I feel that is to be expected since it is HE and uses less water. I will give it that and I dont have to dry nearly as long. But that is where my positivity ends. Clothes dont always come out totally clean. And then there is the issue with the horrific grinding noise. The machine has been making a progressively louder, angry, grinding noise with a high-pitch end note. And as of today, a horn type noise has started. Lovely.I anticipate the machine is on its last legs and I have only had it a few years. I spent too much money on this and feel like I have been misguided and, quite honestly, ripped off by Maytag.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

Absolutely the worst experience ever. The repair people that were sent to address the problem were great but the Maytag people did not care. I bought a new electric convection oven, the convection never worked. The repair people came out several times and checked and adjusted to try to fix the issues but the oven is totally inconsistent. Even the repair people thought I should have gotten a better response from Maytag! Maytag just said that I had a repair but not replace warranty - of course the warranty period is over now. I had trouble from the beginning, I would never buy another Maytag product. I thought that a company that supposedly has a great reputation would care more about their customer.

I purchased my Maytag dishwasher thru Costco. I did so because I got a 2 year warranty if I bought thru them. The washer was approximately 6 months old and they replaced the pump. Approximately 3 months later they replaced the heater. Approximately 4 months after that they replaced the entire operating/electronic board located in the door. Approximately 6 weeks before the warranty was up they had to rebuild the middle dish tray. Now that the warranty is expired by 2 months the door is leaking like a sieve. Unlike most families we use our dishwasher at least twice daily. In summation I would not recommend this brand of appliances to anyone. I will not pay to have this one repaired.

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

We bought this brand new washing machine just 6 years ago. Went with a Maytag because they are supposed to “last forever”. Ha! Last weekend it stopped spinning. Water would drain but no spin cycle. Had a recommended repair person come out and he said it was unfixable. The bearings were shot. This is crazy. There are only two of us using this machine how could it be totally unfixable 6 after only 6 years. The average washing machine life is supposed to be 14 years. No more Maytag for us.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

Ive had this Maytag microwave for about 4 years and the magnetron had to be replaced. The keypad was replaced three times due to SE code shutting down unit which happened again. When I explained this to Maytag, they said it is out of warranty. I explained to them that the last keypad which was replaced was only 6 months old. They replied but the unit is out of warranty! I would never recommend Maytag or any affiliated companies to anyone.

I have had may BravosXL washing machine for 5 years and it is now sitting on the porch waiting to go to the landfill. It has not worked properly since day one, did not clean the clothes properly and even left dry spots where the fabric didnt get washed. Approximately 6 months ago it started making a loud noise while spinning. This week it literally exploded and there was water and oil everywhere, lifting the floor in the laundry room. I am shocked that Maytag would attach their name to such a poor product.

Our range and oven are reliable and durable. Easy to clean and have lasted a long time. I do not regret spending a little extra money to have an appliance that has lasted a long time. The oven heats up at a standard rate. The self clean function is very thorough. I have a white set. I was worried they would stain with your typical spills that come along with cooking. However, They clean very easily.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

I bought Tapan gas stove last year, but all your ranges have a problem. Whenever we clean the range, it never goes straight stay up ,even when I bought from Lowes Store and I told them they said that defect from manufacturer. You have to correct your manufacturers defect, I want an answer as soon as possible. Thank you.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

We purchased a Maytag Gemini gas range last year in April and the extended warranty. The ovens have not worked correctly since we bought it. I never do this type of thing, however, I am just disgusted! I am going to exercise my right as a consumer to express my customer dissatisfaction and share using the social network. I dislike Maytag and even dislike A&E factory service more! I have never experienced such bad service on a new appliance. What is even more concerning and the reason I am posting this warning is there appears to be no recourse! I googled search both companies and the first things that came up were complaint pages. How sad! Buyer beware! If you buy a new appliance, research the warranty provider. It appears that Maytag has laid off the Maytag repairman and went to a lost cost unskilled service provider! A&E repairman has no idea how to fix the oven. He replaced the part. 4 weeks later, came out and walked in the house and did not even look at anything and ordered the same part again. He told us he would be back the following Friday. He did not schedule an appointment. I called on Thursday before he was due to show on Friday and A&E told me I had no appointment scheduled. They told me to inspect the parts that were shipped. I told them I would not even know what I was looking at! They told me the repairman would be back out between 1-5PM on Friday. No one showed. At 2PM, I called and A&E said the repairman must be on his way because he did not call and say he wasnt coming. But again, he did not show! I made no less than 6 calls to A&E and Maytag after that! A&E would not escalate the situation to a supervisor and on call number 6, when I finally got to an advocate, they told me to call Maytag! I have taken 4 days off as vacation to be home for the repairs and this last day was the final straw. When I researched escalating paths for both companies on Google, the first thing that came up was whole pages dedicated to complaints for both companies!

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

We bought the Maytag Washer and Dryer set about two years ago from Home Depot. We have had to have the washer repaired several times in that two years, most recently for a cracked mother board controller unit. The same day we had to have the washer repaired, we also had to have the dryer repaired. Lint and dust is not properly filtered out by the filter and accumulates inside the dryer where it should not be, up against the gas heating unit. The repairman indicated that it was badly scorched and that we were lucky it had not caught on fire. Another customer of his had the same unit, which burst into flames one day when she had left the house with the dryer going, causing a house fire. The quality of these items is highly questionable. Having to spend nearly $600 to replace a cracked mother board only two years after purchase simply is unacceptable.

We purchased all Maytag home appliances when our home was remodeled about five years ago. After the first year, the microwave had to be replaced because it malfunctioned. The dishwasher stopped working in the third year, and now, my refrigerator (model# mf12568AEB) wont cool. The technician told me that all of the Freon had leaked out because of a design flaw. Moisture had gotten into the compressor, and with the cost of repair or replacing the compressor, I would probably be better off buying a new refrigerator, preferably not a Maytag.

I bought the top of the line Maytag washer. I was told they have improved their washer so that it no longer requires an agitator. I was also told the new machine saves you money by using less water. It has a sensor so that it only puts the water needed to clean your clothes. Instead of filling up with water and having the agitator to stir the clothes around, this new and improved machine puts a small amount of water in the machine and vibrates. The end result? All of the dirt and debris gathers in small pockets and sticks to your clothes. In order to save water the sensor only allows a small amount of water to enter the machine to rinse your clothes. When you consider how many times you have to go back and rinse your clothes before you get the caked on dirt off of your clothes, its costing you more money, more time and more aggravation. Oh yea, the maintenance man was out three times before the machine was a year old. The last visit was to replace that fine Maytag motor that was less than a year old. I have pictures that show my clothes with caked on dirt and debris on them after they have completed their wash cycle. It is HORRIBLE!!!

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

I have an MSD2542VEB01 model refrigerator purchased slightly over two years ago. I have the same problem as many others, which is the plastic breaking on the shelves. The first time, it was within a year and the part was under warranty. It is now a year and a half later and one is broken beyond use and another is cracking again. Maytag refuses to help me as there is no “recall and the plastic is not available separately from the easily removable glass of the shelf. The least expensive price that I can find for the shelf is $107 and I need two of them. $214 (plus shipping) when all I need is two pieces of plastic? Be very careful when selecting your appliances.

We purchased the washer and dryer set from Lowes about 5 years ago, and purchased the extended warranty fortunately for us. We had good luck with the washer for about 6 months, then we had to call problem service out because the washer filled with water but wouldnt do anything else. It took several days for the service people to come out and when they did, they had to order parts to do the repair, so we did not have a washer for a few days or a week. They got the washer fixed and everything was good for a few months, then our dryer quit working. We were told that the tub of the dryer had come off, so they had to order another one. So we were again without a dryer. Once they got the parts in the repair company that was sent out to fix our dryer, did not fix the dryer correctly so we had to call Lowes repair service to send someone out again. We have owned this set for over 4 years and once again our dyer has gone out. During all of this time, I and my Brother had to leave our job in order to be home and meet the maintenance people to fix both washer and dryer. I would not recommend this set to anyone, this is one of the worst sets that I have owned. I thought Maytag was a brand that you never had problems with, but we have had nothing but problems with this set.

I moved into an apartment home in June 2016. My apartment was furnished with all new appliances. The washer & dryer were purchased in May 2016. I live alone so on average I do 1 load of laundry per week. In November I noticed paint peeling on the inside of the dryer drum. Each time I use the dryer more paint peels. I contacted Maytag because I figured the dryer was still under some type of warranty. They sent out a technician only to tell me this was a cosmetic problem and cosmetic problems are not covered under the 10 year warranty. I would need an authorization code from Maytag if it was covered under warranty.Again, I contacted Maytag and now they want to send another technician for a second opinion. I dont feel this is cosmetic because the dryer is only 6 months old and already the paint is peeling. I feel this is a product defect because this type of problem shouldnt happen on a new appliance. I have scheduled an appointment for a second opinion and if he says its cosmetic then I have to pay out of pocket for the repairs to fix the problem. I thought Maytag stood by their product and customer satisfaction was a top priority. I guess I was wrong.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

The pulley on the dryer vent keeps falling off due to poor design. We had a repairman fix the problem under warranty, but the dryer was purchased in 2010 and this is the third time it has fallen off. I have taken the dryer apart and repaired it myself, as I am quite capable, but I called Maytag Customer Service to see if there is something else I should do or replace. They told me they never heard of the problem and they would recommend a service man repair it, which would cost me money and It wasnt needed. No updated part was recommended, or any other help at all, for that matter. I am very unhappy with the Maytag products and will never buy anything again.

I bought a top end Maytag refrigerator with the freezer in the bottom drawer. Spending the extra buck was something that I thought was worth it, being a Maytag. Fifteen yrs go by and it stops completely. It cost me 200 bucks for a service technician to tell me that the compressor or it has a leak. Its not worth repairing. With todays cience and technology, you would think that they can make a refrigerator last for 25 yrs or more, like the old ones. We went to the moon 44 yrs ago. Why cant they make them to last? I think that the corporations figured they can make more money making an inferior product that needs to be replaced every 10-15 yrs. I will never by a Maytag again.

I think that I finally figured out a way around the piece of junk Maytag sold me. I bought a Maytag french door, stainless, yada, yada refrigerator in 2006. When it broke down, see later description, the first several times it was ok because of the warranty. This POS has failed 7 times requiring $300+ to fix every time. When contacted about the issue, the people at Maytag seem happy. The business model is working perfectly. There goes another sucker. The refrigerator begins its eventual breakdown with the door alarm light and sound beeping constantly. Beeping that continues for days and weeks. The next progression to failure continues with it not beeping anymore but now the interior lights do not light when the refrigerator is opened. Finally, the refrigerator stops cooling entirely and it is dead.Now, Maytag no longer wants anything to do with it so you need to call a repair man. When the repair man arrives, the entire time he talks about what a piece of junk Maytag is. They, every time, at first think it is the switches and replace them. This NEVER fixes the issue. Next, they have to replace the computer brain. $400 to fix. EVERY TIME. Now, at least every year. If you buy Maytag and have a similar experience, get your wallet out. Sell you junk then dont stand behind it.