I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

I just bought a brand new Maytag microwave a few weeks ago. The door is already broken! I’ve been sitting here 4 hours! waiting for a repairman man. No call, no show! I am missing work and gym time because MAYTAG sold me a faulty microwave in the first place! Never again will I buy Maytag products!

This Bravo Top Loading Washer does not thoroughly clean my clothes. It doesn’t fill properly with water, and it leaves soap residue on my clothes, because it’s not using enough water. I’m using the 2 rinse cycle trying to prevent this, and it’s still not enough. It has actually ruined a few of my items. It is the WORST washing machine I’ve ever purchased. I’m disappointed in Maytag for producing such an awful machine and Sears for selling such a sub par product.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

My disappointment with this washer (Bravos xl) is that it smells moldy and musty no matter what I do. I clean with affresh when light comes on, leave the top open, etc. I have tried cleaning it with baking soda and vinegar poured down the detergent opening. Water does not drain from the bleach or softener openings. I have resorted to using baking soda in every single wash and adding an extra rinse to keep my clothes from smelling. The laundry room always smells. I would go back to an agitator in a heart beat if this hadnt been so expensive. DO NOT BUY THIS MACHINE.

After only 4 years, this washer stopped spinning. Called Maytag support (Ha! the ads show the Maytag repairman sitting by a non-ringing phone) I had to wait 20 mins to get through. Only after paying for a service call would they be able to determine if this problem was motor-related. In reading reviews (which in hindsight I wish I would have done prior to purchasing) this is a common problem and is related to bearings going bad. Pay for service call vs buying a non-Maytag product -- will set this out by the curb and buy a different brand.

Maytag 765 Washer - What a disappointment after having a Maytag set for 2 decades only to get a new one that isnt worth much quality wise. 2 new washers in 2 weeks due to a ratcheting noise that they both have. The solution??? Have a third service call only to hear, replace it (which we did) or replace the transmission. The 3rd call coming up will be the same. What good is a new transmission going to fix it when the last 2 machines had New transmissions. Quality??? I dont think so. Oh, I had to buy the second replacement in order to get credit for the first one. This was at Lowes. Is there even a quality washer out there anymore?

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Ive only had my Maytag Bravos XL Washer for two years and I HATE it. It constantly gets off balance during the rinse and spin cycle. What should take 30 minutes takes triple the amount of time. My washer is in the basement and I constantly have to run up and down the steps to readjust the clothes in the washer. Ive started to just stand by the washer now during the rinse and spin cycle. What a waste of time. I would not recommend this washer to anyone. Also, it does an awful job of rinsing out the detergent and softener. All of my dark colored pants have detergent and softener residue on them after they come out of the washer. Ridiculous!

Bravos washer purchased Sept. 2016. I purchased the Maytag washer based on experience and reputation. I am so disappointed in this washer. I have had the control board replaced after only 3 months and it vibrates, shakes and is very noisy. It does not fill with enough water and the clothes are tangled at the end of the wash. I will never buy another Maytag.

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

I have owned this washer for three years and the smell in the entire area of my home is getting unbearable. I have used vinegar, clorox, and washer cleaner and I always leave the door open when the washer is not in use. My other complaint is that even a small amount of bleach cannot be used on clothes without causing bleach stains because it runs directly on the clothes before enough water is in the washer. The receptacle for softener also does not dispense the softener properly. I am very disappointed in this machine.

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

Like all of the other reviews, I have had this microwave less than two years and it won’t run and reads “door open”. I am filing with the Better Business Bureau as the product advertises “partS” under 10 year under warranty when in reality it is one part with a VERY limited warranty. In order to determine if my issue was covered under warranty I would need to pay $189 not including parts in labor. I called several times and customer service indicated that they had never heard of this issue (which upon looking at this site seems hard to believe) and I would need to gamble the $189 to see if it was covered. Terrible product, terrible customer service.

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

Bravos gas dryer - three issues in three years. Same issue twice, clothes are not drying. Now I have company coming and have to deal with his issue. The blower motor went. So, I have paid for a new dryer in repairs already. The washer is making such a loud noise when it goes into spin cycle that you have to turn the volume up to the highest level on the TV and it is still tough to hear. It’s unbelievably in the horrible quality. Make the product and parts in the USA and stop buying junk from China and Mexico. This is good American money that is flushed down the toilet with Maytag as well as your reputation. Fix your quality control and do the right thing!

3 years into the buying of a Maytag Bravos XL MCT washing machine (Serial # **) and already had to replace the original control panel for a cost of $400+ in less than 2 years of the buy. Now AGAIN the replaced control panel is now once again shot and the machine is not starting. The appliance needs to have a #manufacturers recall for the control panel. #Maytag #Whirpool #BetterBusinessBureau Note -- all existing customers, please lodge manufacturers complaint for the control panel issues @ 1-800-344-1274. (Even if you dont pay because of extended warranty or plan coverage, if you are facing the control panel issue year on year). All future customers, buy this appliance at your own risk.

Maytag Dryer MED6000XR2 - Purchased in Sept. 2012 - first service call 1/13/14; 2nd service call 2/20/2015 and less than one month on 3/14/15 it goes out again. It takes one week to get service company out and then another week for the part to be ordered and put in. This means I am without a dryer for over 2 weeks. An $1,100 dryer goes out every year and sometimes within one month?! According to the service company, it just is the way this dryer works. Really? If Maytag ever wants my business again, I better get a more justified reason and better than 2 weeks service call. This is absolutely ridiculous.

Do NOT purchase a Maytag dishwasher. What happened to the Maytag repairman being so lonely. Now he has lots of company in the way of angry consumers. Purchased a Maytag dishwasher and less than a year later the control panel failed. It was still under warranty but the service person just tweaked it instead of replacing it. Now, less than a year later it has failed and will cost over $200 to replace and repair. This is disgusting.

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

Dryer doesn’t dry any size load in one cycle regardless of settings. Mysteriously, it triggers a message to check the lint filter and line when running a small load with nothing blocking the venting system. It never happens on large loads which would block more of the air flow. You could get a comparably sized dryer for much less. This not the premium product that you pay for.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

I have the washer. It has a bad sound when changing gears like grinding and there is no way it is putting enough water in it to wash clothes. It is a very loud and noisy washer, serial c42831812.

Neptune washer maxima XL steam - Our machine is only 2 years old and we feel the soap dispenser is defective. That little door inside to choose either liquid or powder is not flush with the basic cup and to make matter worse, there is a V shape hole at the bottom of that little door. Meaning, fill it up, and while you are looking for the softener in your closet, all the expensive liquid HE soap is on your floor! And when you close the door, if you wait for starting the load, all the soap goes into that rubber gulley instead of being sent over the clothes. I just got off the phone with them, they wanted to send a technician AT MY EXPENSE - when I do feel it is a deign mistake, not a use/abuse on my part. I proposed instead to send them a picture. They refused. I proposed to send them the soap drawer, they refused as well. I will never buy Maytag ever again and dont recommend to anyone to go to this Brand name!

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

Maytag french door 2015 refrigerator. Not happy at all. Freezer gets rim frost on sides of pull drawers and the smell is like dirty socks when motor is running! The whole kitchen stinks???

On June 17, 2013, we purchased this over the stove microwave for my elderly parents. They use it daily to heat their lunches. In December 2014, it would stop turning and finally in January 2015 it completely died... no heating and no turning. The technician quoted a repair at $200 when we only paid a little more to purchase it. I emailed Maytag to tell them that it was manufactured and purchased in 2013 with light use and that it should never have died in such a short period of time. An e-Solutions Specialist contacted me to tell me that they certainly understand my frustration, but that occasionally failures occur and that there was nothing they could do. I replied back that they could DO something because they were customer service and that was there job. No reply back yet, but after seeing so many of the same issues here, Im not holding my breath and I would never buy or recommend a Maytag product of any kind to anyone. I dont expect 15 years from an appliance, but I certainly think 18 months is just wrong.

A refrigerator we have had for just two years has been leaking water from the freezer and damaged our hardwood floor. We thought it was someone dropping ice or leaving the freezer drawer open but no, there is an admitted problem with the mechanism. No coverage from Maytag for the cost of fixing THEIR MISTAKE. The company doesnt seem to care. Got the run around from their management.

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

Washer was purchased at Lowes under direction from staff... Great washer, environmentally better, less water consumption... Well washer is piece of crap. Activator is out, door stays locked, have to unplug to release every time used, water does not drain and cycles do not function or start. Lowes no longer carries product and all other review on spot as to cost to repair... Piece of crap, loss of $600.00+. Could be used as target practice, best case scenario.

We purchased a Maytag double oven in November 18, 2008. I was baking and the top oven wasnt working. We called Maytag service number on the book we received when we purchased the oven. It took 25 minutes for someone to answer our call. The person did not know what our problem was. We thought it could be the ignitor. He transferred us to a parts person. That person didnt know the answer and hung up on my husband. How rude of him. We will never purchase another Maytag product. We will let our family and friends also know. You need to inform your personnel to know their products.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

I bought a Maytag dishwasher, when I bought my house (7/2010). I live alone and I use my dishwasher only once a week or once every two weeks. After 3 years of working perfect, it stopped working. I had someone come look at it. After troubleshooting with the basic steps, making sure the water was correctly hooked up, a fuse was not the problem. The dishwasher door was shut completely. He took the racks and all movable parts, & thought something, a piece of glass, etc, was stuck in the drain. Nope. After reading these reviews I realize it is got to be the control panel because the start button will not come on and all these people have the similar problem. It just stopped. Period. The panel lights come on, but not the stop button. I am a single person as stated and on disability and on a very tight budget. I bought a Maytag because of the name and reputation. How long would it have lasted under normal use, say a family of 4, using it nightly? Certainly less than a year. I have no idea what to do now. I cannot afford a repairman, & I am certain it is the control panel on the dishwasher. I do of course have all the model numbers, etc & papers, when I bought it. I can provide proper paperwork, when contacted.

DISHWASHER MDB7749AWM - We purchased this dishwasher from Home Depot on 10/15/2011 for $630.00 for my birthday and yesterday the start button stopped working (cycle lights still work). We went online to look for more troubleshooting options and we found lots of complaints about faulty control panels. Sounds like thats what we have. VERY disappointed in Maytag for not correcting known issue. My dishwasher is only 3.5 years old and there are only 2 adults in our home. We run the dishwasher 1 to 2 times per week meaning this Maytag dishwasher will only last for about 200 wash cycles. Shame on you Maytag!

We like the refrigerator and we have had it several years. But the thing the top freezer conceals much of the top rack of refrigerator. We must duck and almost kneel to get to food inside. Next fridge will have drawers and doors that open on both sides.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

Purchased our Maytag in October 2009. From the beginning it would make loud, popping noises occasionally but seemed to work just fine. At the time of purchase, we opted to buy the 5 year extended warranty for $125.00 (just in case). Here we are at seven months after that warranty is no longer any good and the freezer leaks all over the floor and we have to keep a towel at the bottom to soak it up.This morning I wake up to the panel being completely out and fridge is not running at all!!! We thought when we purchased our Maytag that we were buying the best of the best... not even close! We just paid for an expensive piece of junk! Who has the extra money just lying around to go buy a new fridge? Not us! This is unacceptable!!! I have read other reviews that sound pretty much exact to our experience with this refrigerator. I hope somehow they can and will be held responsible for putting this product on the market knowing full well it is an over-priced piece of junk.

Bought a new Bravo washer and gas dryer; Dryer model mgdb980bg. Bought it September 2013. I have had nothing but problems. The dryer would run for 10 minutes then shut off saying check lint trap. Then once it started going again, it close were even damp. It wouldnt sense so it wouldnt start. Finally it got to the point where I couldnt get my dryer working so I phone repair place. The guy came out and set the temperature. Gauges or sensors were off by over 20 degrees as well our entire starter motor was shot. That was over a month ago and we are still waiting for a part that is apparently back ordered. I call today and they said its a faulty dryer and it could take anywhere from a week to two months to get the part. I am requesting a new dryer.

I cook a lot so we wanted to purchase a double oven. We purchased this double oven about 10 months ago. Every day I complain about this range. It cooks very uneven. Called Maytag and they sent out a repairman who said I needed to preheat the oven for 25 minutes before putting my food inside. Dont pay any attention to the beep, because when it says it has preheated but it really hasnt. To think you pay that kind of money for such a piece of JUNK!! Also, I have owned 2 other glass top stoves (the last one I owned for 23 years) and never had a scratch on the surface. Theres already a big scratch on this new one. Glass top on this one is such poor quality. Would not recommend to my worst enemy.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

A dishwasher was on sale $500 and stopped working in under two years. It was a stainless steel Maytag. No one will help service it, and it seems unreal that a dishwasher should break down so very quickly. To not already work in under two years is astounding.

Under class action suit in 8/2005, Maytag repaired my Neptune washer by replacing motor conversion kit. 6 yrs later the washer is having same problems as had originally; we asked Maytag just to replace the motor drive again ($190.00 part). They refuse, although this motor drive had identical life span to the one they replaced. It seems the replacement part was not new and improved, it only lasted as long as the original. Only now, we are past the class action suit deadline by years.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

Series 200 dishwasher wont start. Just over 1 year old. Control panel needs replacing which I found out, is a constant problem and a design flaw. Called Maytag and they would only offer 25% off new part. Why would I do that when it is just going to go bad again?

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

I purchased a Maytag Bravo washer and dryer in 2008. I had a repair person out today on both units. I was told that it will cost as much to fix the washer as it would be to purchase a new one. As far as the dryer was concerned, I was told to live with the timer issue rather than replace the expensive mother board. I was also told that the drum bearing issue with the washer is fairly common with the Maytag machines. It looks like the Maytag repairman isnt so lonely anymore! I paid a lot of money for these machines and they amount to a hill of garbage after three years. I may be buying a new washer, but you can bet your boots it wont be Maytag/Whirlpool!

My Maytag refrigerator is less than 5 years old; the compressor went out (only warrantied for 1 year, 5 years used to be the minimum). I contacted the company who now owns Maytag, I believe Whirlpool. They told me they can fix it, no matter what the problem is, for $380.00. It turns out they sold me an extended warranty, but that was never explained in the conversation. Prior to contacting them, I had Sears out to fix it; they are the ones that told me it was the compressor. 1 week after buying the extended warranty, the repair company came out to fix it and found out the refrigerator was unplugged and informed me it needed to be plugged in for 24 hours in order for him to determine what was wrong with it. I scheduled an appointment 1 week later. When they came back, they said it was the compressor, and they needed to order the parts. 1 week later, they came back, and the compressor they came with did not work. 3 weeks now, no refrigerator. They said they would put a rush on the order, haha. Now, I have to wait another 8 days for them to come out to repair. 4 weeks without a refrigerator? I think there is some type of implied warranty when you purchase large appliances; these companies are getting away with murder. Are refrigerators now disposable commodities? Cheaper to buy new ones than repair the new ones? What will happen to our landfills?

I purchased a Maytag French Door Refrigerator in July 2011 from Lowes online and had it delivered on August 16, 2011. In September 2011, I could not get the ice maker to work. So I called Lowes and they called in a repairman. He came and replaced a part to fix the problem. I dont have any complaint with his work but here it is, October, and the ice maker makes maybe four ice cubes at a time on a good day.I am really disappointed with this product and according to their commercials, I would like to know which of these techs are setting around doing nothing, maybe he could come and fix my fridge once and for all. I would sure find it difficult to recommend any Maytag appliance as a result of this mess. I could call a repairman myself, but I was under the impression thats what a warranty was for. According to Lowes we are required to call them and they will schedule a repairman or the warranty isnt any good. I replaced a GE French Door with this Maytag, I sure am sorry I chose this Maytag.I know an ice maker problem is minor compared to some of the complaints on this appliance, but when you pay good money for a product you have every right to expect everything about it to work. Im just wondering where these appliances are actually made?

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

Purchased a maytag washer last yr. and I feel it is the worst washer I have ever dealt with. I hate that every time I wash somethings they come out with lint all over them and they are the same things I have washed before and never had the problem, plus I hate the cover locks so you cant put water in before you put soap in.

Bravos mct. Unbelievable, this washing machine is terrible, no water. The water level doesnt even cover 6 items. Have to wash triple the loads of my old washer just to get the clothes clean. I have to go to the laundromat twice a month. I shouldnt have to do that. Almost want to fill the washer with water, but dont know what will happen. Very unsatisfied with this washer.

I bought the product thinking Maytag - should last a long time. Sadly I was wrong. Bought the microwave from Home Depot in May, 2016 and had it installed by them. The product worked fine for the first 14 months. In fact I thought it was great. It was quiet, heated things quickly - a great product. In July, 2017 I started having problems. The product would start. I was getting a message to Close the door to start the microwave, even though it was closed. When this would happen I noticed that when the door was open, the light wouldnt come on. It would require multiple open/close until finally the light would come on (when door was open). Only then, when I closed the door would the microwave operated as it should. I lived with this inconvenience until Dec, 2017. Of course - over the holidays is when it decided to quit working entirely.I did my digging and found problems with the switches. I replaced 1 switch - still didnt work. The cost to have a repairman come out is ridiculous (Sears wants $250). My frustration was growing and my confidence in the product was waning. So time to get another microwave. I was done. Frustration and anger doesnt begin to describe my feelings. I went with another brand. It isnt installed yet, it should happen this week. In the future I will tell friends to avoid Maytag microwaves. Apparently they just dont last. I realize this isnt a top of the line microwave, I only spent $299 (plus tax, installation...) but really - shouldnt it last more than 14 months before it starts giving me problems? Very disappointed!!!

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

Five years ago made a major investment on new techno with this washer/dryer. This is an updated review. Since the beginning the washer causes awful water hammer. Tried using arrestors, they dont work. Clothes are stretched out. You need to bundle each piece of laundry! The wash takes forever. Top loader has lid lock, very inconvenient - Dryer is OK but needs extra drying time. Would not buy this washer...

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

I reviewed lots of reviews, and decided that the negative reviews ones were sour grapes or uninformed customers! WRONG! Do not buy this washer. I replaced a 16 year old Frontloader Bosch! Should have had the Bosch repaired, but wanted a topload for a change, new look etc. From day 2 the washer began to squeal during the early cycle and at the end as well. Maytag repair was out for an unrelated repair on another appliance. I told the tech about it and he suggested its brand new etc, give it time to settle in.Now 4 months in and another service call to tell me its nothing!! It squeals so loud I can not run it while in the next room. I have videoed it and sent it to the Maytag repair in Glenwood Springs, and he said I should load it only full enough to see the impeller at all times!!!! Forget a full load of work clothes or a pillow or blanket. Which is to be expected to be able to wash. He said I needed to spread the clothes out manually along the outer sides of the TUB only, prior to washing the clothes! not over the impeller. I am not kidding! This is a open tub, so the impeller is the little thing in the middle on the bottom. I advised him, I videoed the event and even with three socks in it for a test it still squeals like a (well you get the idea). Trying to get Maytag help, but nowhere. Matching dryer door hinge broke first week, it has been repaired. Not good quality at all for the top of line Maytag. Then Maytag Man must be busier these days, than of old.

I purchased this washer three years ago. It worked fine, but all of a sudden the washer stopped spinning and was not following any of the cycles. Of course it was out of warranty. The repairman states the computer board on the washer is fried and will cost $400 to replace. Several stores have stopped selling Maytag because of quality issues. No more Maytag for me.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

I think so much about Maytag dishwasher with electronic controls that I decided to fix up my Maytag mdb3700awx by replacing the motor. It has an old fashion timer. It was trouble free for 10 years until the water supply line fail and sprayed water on the motor and shorted it out. I got a use motor and pump from eBay for 40 dollars. The dishwasher should last 20 more years. Too bad Maytag dont make them like they use to.

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

Purchased what was supposed to be a good dishwasher. In less than 3 years the control panel went out. It would cost more to replace the panel than to buy a new dishwasher. I will never buy another Maytag product.

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

Update 3/7/2018. I have been without a working microwave since 1/23/2018. Technician sent from Maytag came out to repair it and said he needed to order a new board and door switches. These items were installed on 2/26/2018 but did not solve the issue. The technician said the microwave needed to be re-wired completely and would schedule for the microwave to be removed and brought to shop where it would be repaired. After I called Maytag and explained the situation they told me they would replace the microwave (with the same model.) I called today to get an update on when the new microwave would be installed and they said not for another 14-21 days!!! After expressing my displeasure at the whole situation I was told by the Maytag representative that I could choose any new microwave model (under $399) from the lines of Maytag, Whirlpool, Armana, or Kitchen Aid. It would take about 14 days for delivery and they would schedule the installation at no additional cost to me. So now I am researching microwaves again!!! Ill update this review once the new microwave is installed.

I have done absolutely nothing to this dryer except keep the lint screen clean. Have had it for 15 years. Keeps on tickin. It is used daily. Sometimes 3-4 times a day. The outside looks rough. But who cares. I bought a new lg washer with great looks and had it just a year and 2 weeks. Had to spend another $200 on it. Still doesnt work right. Im Maytag all the way!!! It is a simple dryer. But it is a workhorse. It was a gift from my mother and have so much appreciated it. It has been an amazing piece of equipment. From now on I will only look for the maytag brand for whatever appliance I purchase.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

I purchased a MTW6600TB0 Washer and Dryer on 6/17/07. I have had issues with the washer from the beginning; smell in towels and mechanical problems as well. The machine does not fill properly and receive error codes that are electrical issues per A & E service. I get LF errors occasionally and randomly on different cycles. I finally called for service because I now am receiving F51 Error, which has to do with the basket per A & E service technician. I was told on Black Friday that my machine required both baskets and the rotary motor. My machine is just 4/5 years old. No unusual wear and tear. There are only three people in my family and we live in a fairly warm climate so no heavy winter clothing, etc. I was told that my stainless steel basket was rusting to my plastic basket. I am still trying to comprehend the fact that two materials that are not supposed to rust are rusting. After looking for a new washer over Thanksgiving weekend, I find out that Maytag warranties their stainless steel basket and rotary motors for 10 years. So do they warranty the things they say the warranty or not? Of course, it is a holiday weekend and I cannot get a hold of Maytag. I paid for a service call and the technician told me I would be responsible for the repairs at about $500 for parts plus labor. I looked up the parts he recommended replacing and it was over $800. I paid $1000 for this machine less than 5 years ago. Thats $200 a year for the privilege to use a Maytag. Additionally, my set is black. I can not find a black washer anywhere.

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.

Got the dryer free when we moved into our townhouse. We had been doing 2-3 loads a day for almost 8 years. The dryer was old when we got it. No complaints. Just wish there was some way to fix it. But mechanic said, No way. Almost a valued member of the family. Say 2 loads a day, 7 days a week, 52 days a year. This is a lot of loads. Remarkable. New machines cant do that today says our mechanic, they are not built to be fixed. Now, when broke, replace, don t fix.

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

In the last 6 years my husband and I have bought the high end front load Maytag washers and both have crapped out within the year. I will never buy another product from this company again. Their customer service was no help and the washer needs to be rebuilt. We are waiting for parts which are back ordered months in advance. I will have no washing machine for at least 2 months. I do not trust any product made by Maytag and any company who sells Maytag should be ashamed to sell their product. There is nothing that I have experienced that would make me trust this company whatsoever!

Purchased my Maytag range/oven 14 years ago and it still works to this day. I had to replace both oven heating elements. I am a do it yourselfer, took me less than 5min to replace both. The cook top is easy to clean. As long as you take care of it, it should last you a long time.

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

I purchased Maytag Quiet Series 300 Dishwasher in 2006. About 3 years ago, I got a letter that a recall had been issued due to an electrical problem. A service repair person came out and replaced the electrical element in question. Next the dishwasher did not work and a repair had to return again. Today I have the same electrical problem and after waiting on line 12 minutes to talk to Maytags customer service, I was told it could cost me a couple of hundred dollars to repair my 7-year old dishwasher. In my last home, my Kitchenaid dishwasher lasted 20 years before needing to be replaced. My daughters Maytag dishwasher lasted on 12 years. What ever happened to Maytags lonely repairman? I now have to get a new dishwasher and worry about my $3000.00 kitchen floor getting damaged with the removal of old and install of new. Believe me, my new one will not be Maytag.

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

The dishwasher turns on of its own accord. Sometimes when you get too close to it, once in a while in the middle of the night, and most of the time when you latch the door. It does a great job cleaning the dishes, but to no avail because its always in the middle of a cycle when you need them.

We paid over $800 (more with installation) for this quality dishwasher. Within one year we began to experience problems with this unit. The top control panel easily becomes water logged causing the device to fail.

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

Purchased a Maytag dishwasher from Best Buy. We did not buy the extended warranty from BB because there is a warranty with Maytag. After 4 months of use the washer stopped working. We were unable to return it to Best Buy because we exceeded the 2 week return policy and needed to rely on Maytags 1 year warranty. It took over 2 weeks to schedule a repair and he was unable to fix it, it needed an entirely new Control Board and UI panel. 3 weeks later he returned with the new parts. It worked for 10 days with the NEW Board and panel, it has now stopped working again. We are not able to replace it due to the California Lemon Law which allows a company 3 opportunities to fix it before replacing. Next time I will purchase the Best Buy warranty so I can replace this Maytag LEMON.

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

I Hate this machine. It does an inferior job and I wish I never bought it. Our Bravos XL washer was purchased in spring. It left white residue constantly on my clothes. Even WORSE, the machine wrinkled the permanent press so the clothes had to be ironed before wearing. (I rarely had this with my last washer). I used the machine settings correctly and I called the company and basically...was told, Youre out of luck. I hoped that it would improve but No Way! Dont purchase this machine, dont waste your $$$.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

We bought a Maytag Bravo model top washer recently and have no good things to say about it. The startup time is too long and clothes are coming out with lint all over them now. If the unit could be returned we would do it immediately but we cannot.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

Thinking that the Neptune fiasco was over, I happily bought into the sick company and got burnt 3 times for all 3 purchases. The Gemini range with dual ovens: the controller clock with all relays and electronic package is dying, leaving me with no ovens, or slow heating and an alarm in the middle of the night. Now, even the burners are not working properly. Junk at any price, and I paid $2,400. Not 5 years old and repaired several times under warranty; all were electrical failures.The fridge is another failure. Apparently the Freon is leaking out. It is unrepairable and it was typical of these from what the service guy said, not 5 years old. It was repaired once, leaking on floor. Apparently, it was a kinked drain hose. The dishwasher was one year old and it caught fire when the dial was turned while the machine was running. The 4th machine, an over the range microwave, is still running… although from day one it sucks so much power on the dedicated line that it dims the lights in the microwave as it starts up and each time, the magnetron energizes. I am just waiting for it to fail too. Can you say never and mean it? There was no goodwill offered. “So sad” and “too bad” is the common line. Nothing will last more than 5 years if you listen to sales people at Maytag - junk. There was no help from the corporate office. Nothing I can do for you. Junk, junk, junk.

I have Maytag Neptune washer and dryer that was purchased in 2002. Theyre still going strong. Its a great size for empty nesters like us, but if you have a big family, you might want to consider a larger capacity.