My washer (Performance Series 4000) needed new bearings about 6 months after purchase. By the time the parts came in and after the A&E repairman rescheduled because he didnt know how to replace them, another two months had passed. Now, a year later and with no more warranty, the bearing needs replacing again! This washer is only 1 year 8 months old! The first repair cost well over $1,500 but was covered under warranty. There are hundreds of other people with Maytag washers having the same issues! Maytag is well aware of the defect and refuses to take responsibility. I would like to file a class action lawsuit against Maytag. Im in Tennessee. Please contact me. Thank you.

Called Maytag to set up service call at around 9am for my washer, was given a rate of $129.00. Thought it was High but it was my only off day and felt confident that it would be a reputable company. If Maytag Priority Service would refer A&E Factory Service to me for service they must be a reputable company. I was sadly disappointed after numerous calls to A&E Factory service, a 5 hour window was not met and they were not concerned other than they would document it. Then I find out that A&E Factory Service has a Rating of 1 1/2 Star rating out of 5 and thousands of complaints to BBB and Consumer Affairs, dropped by Lowes for horrible customer service but Maytag Priority Service recommends them to service their product, says Volume on how Maytag takes care of their Valued customer after the sale. Maytag has lost a customer for life. A product without customer service and trust is nothing but a piece of metal!!!! I will be picking another Brand that doesnt use A&E. Maytag you have lost my trust and you cant buy that back.

We have had the oven, a Maytag Gemini Double Oven model mgt8775xs02, for 3 weeks now and I am so upset. First off, I became violently sick from the oven when we first used it. I had a horrible headache and then nauseousness and then the worst stomach problems I have ever had. The toxic smells coming from the oven were too much for me. We had every window open. I looked online and found other people who reacted the same way to their new oven smell. But now we are on the 4th time using the oven. We did a self-clean and I thought that would help but no, it smells like someone is pouring gasoline into my home. I smelled it in pockets throughout my house. I have had the gas company out twice and a repairman. They all cannot figure out the problem. I looked online to see if other people were having a gas problem from this model and I am not finding it. It is horrible. I feel like I am being poisoned. I have not had a working oven in 2 and half years and I was so excited to get this oven and now my new oven is making me so sick. I am not sure what to do from here.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

I purchased a Maytag Bravos XL washer and dryer at Best Buy (Pacific Sales) in March 2013 at Best Buy. I also purchased extended warranty on both machines. A few months into owning the machines, the washer started giving us a UL error light. It wouldnt finish the wash cycle and had to be restarted multiple times before it would do so. I called Best Buy and they sent out a repairman. He said the set-up cycle had not be run correctly by their own installation team (which I paid for), and he said that he had fixed it.A few months later the problem started reoccurring again. Best Buy sent out repairman again who claimed there was nothing wrong with the machine. He left and the problem started reoccurring soon thereafter. I called again, and Best Buy said they couldnt do anything about it because Maytag could only work on the machine (it was now getting an F:51 error message as well). Maytag sent someone out who watched it run for 15 minutes and diagnosed that it was fine and left. I told him that the error didnt occur until the end of the cycle, but this seemed to make no difference to him (he didnt want to wait).Same thing happened again (might run five to ten loads without an error and then it pops up again), and I called Best Buy again. They sent out the Maytag repairman again (different repairman). He spent about the same amount of time as the previous Maytag repairman. His conclusion was that the machine was fine; he told us that this particular washer (the top-of-the-line for Maytag) gets out of balance frequently and that we would simply need to live with it. Like his colleague, though I told him that the error message doesnt occur until the end of the cycle, he didnt stay that long.Not long after he left, the problem started occurring again. I called Best Buy and indicated that theyve had plenty of chances to repair the machine and that I wanted a new one. They said someone would call. The response: another call to schedule a repair visit. I called them back and told them that I didnt want another repairman but rather a new machine (weve wasted hours and hours of our time giving them a chance to make the purchase right). They then had someone from the Geek Squad call, who swore that hed put his best guy on it and that he would actually work on it this time (ordered parts). He was supposed to show up this past Friday but called in sick (now rescheduled for this coming Friday). In the meantime, the machine (last night) quit working altogether. I have a pile of wet laundry and am faced with going to the laundry mat today.Im at an utter loss of words for this experience. It is truly the most frustrating consumer experience that Ive ever had. Ive watched Best Buy, Pacific Sales, and Maytag play pingpong back and forth across the table for months. I paid good money for top-of-the-line washer but have gotten bottom-of-the-line service. Surely, at this juncture, Maytag and Best Buy will finally do the right thing. I am going down to the Best Buy store this morning to visit with the store manager (and then to the laundry mat...not exactly how I wanted to spend my Sunday). If not, then next steps will be to figure out how to find representation to force the issue of the lemon law. Exasperated.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

The washer machine is only 2 years old and its broke, at first it wouldnt spin and now it wont wash. Everyone is saying between the parts and service fee, it will cost 200 to 300 dollars or more to fix, most technicians wont repair them because they say that we may as well cut our loss and just buy a new one. No one likes these machines. I wish I would have known what a sham the washer machines were before purchasing.

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

One time at around yr 2 of our 10 yr warranty the repair guy removed my agitator, spline gone. Couldn’t find one anywhere! After a month of using a laundromat, I called the company in Montreal and they had the new agitator in my post office in 4 days. I am unable to wash anything that puts the Bravo washer out of balance ie: towels. The sides are busting out on the machine!! We have only had it 4 years so far. Not impressed! Does the warranty cover busting out sides? As it is a major part of the structure of the machine.

Bravo Series Washer and Dryer. I hate, hate, hate this washer and dryer. I have had it for 2 years and hate it more every day. What makes is worse is the over $2,000 spent to buy this piece of crap technology. The engineer should be fired and sham on Maytag for selling such a piece of crap. Washer does not get clothes clean and I have pictures to prove the amount of dirt and lint and soap left on clothes and bedding. Very poor design, and worse yet absolutely horrible engineering.To wash one item on delicate takes 47 minutes. No way around it and you are limited to the water temperature you want to use and the spin cycle that you want for that item. Water level is too low no matter what setting you use. I have read and reread and gone step by step according to instructions with no success of clothes coming out clean. Clothes are also twisted and knotted and wrinkled like no other machine I have used in over 50 years. The washer is very limited in what it allows you to do. Bedding cycle is a joke that does not work at all. One of the reasons I bought this was so that I would no longer have to take the time to drive to a laundromat. I washed a comforter and so much soap and lint and dirt was left on the comforter. I still had to take it to the laundromat to get it clean.Dryer is just as bad. Even with the energy saver off it still takes 1 hour and 20 minutes to dry 4 towels that are 5 years old. I cant imagine how long it would take to dry brand new fluffy towels. It was engineered to sense when ONE piece of clothing is dry. I want ALL my clothes dry, not one piece and the machine shut off. How stupid is that??? Engineers - design it so it senses when clothes are still damp and the machine keeps running!!! I can only use the time dry setting because no other setting even comes close to getting the clothes dry.To top off the hatred of this machine some damn engineer apparently thought this was a car and needed to be aerodynamic with a curved lid on both washer and dryer so you cannot put anything on top of the machine!!! Not every house is 5,000 square feet with plenty of room and storage!!! They want to force you to buy the drawers to put underneath and then the washer becomes too tall for short people to reach down into to get the clothes out. There is not one positive thing I can say about the washer and on top of it I will never purchase another item from the store I bought this set from. I have had service come out time and time again and they say it is an installation problem. Installation says it is service and yet no one will admit it is just a very poorly designed machine. Do not buy this brand or series of washer and dryers. This series deserves a minus and the company should replace every set sold!!!

I have had commercial front loading washers since they came out (first was a Whirlpool Duet); although I like the capacity they have for large quilts and sleeping bags, they just dont seem to clean as well as the agitate-in-tub style, and they can take a ridiculous amount of time for a cycle -- wheres the energy savings there that they advertise? Im going to go back to the agitate-in-tub of water style when a replacement is needed. A lot of hype and expense, and plenty of experience with these on my part, but Im going to grade them a C, at best, compared to the agitator style washing machines I use to own.

Bought a Maytag French door refrigerator MFT2976AEM01 in August 2013. Started having problems before the refrigerator was a year old. I called to get it serviced and it took 4 months to get a repairman to check it out. He fixed one part and then ordered another part that he needed which took 3 months to get. After he replaced that part the refrigerator continued to have problems. The serviceman has been out to repair my unit 6 times so far. He has no confidence in the Service Engineers from Maytag. They recommended yet another part be replaced, however now Maytag will not cover the parts cost.They offered to let me buy a new fridge at a discount. After spending about $2700 in August 2013, I dont have the $ to spend again for a refrigerator. My refrigerator is so loud it has been waking me up for about a month now and I am sick and tired of it. Shame on Maytag for having such terrible customer service! I will never ever ever recommend a Maytag because this has been a nightmare!

I purchased my Maytag 4 door refrigerator with the freezer at the bottom (model #MFX2570AEM) in December of 2012. A couple months ago it started leaking small amounts of water. I now notice that there is such a build-up of ice under the freezer drawer that it wont even close properly. I, like all the other consumers that have complained am fuming mad. I purchased the Maytag brand because of its great reputation for quality products. However, this is totally unacceptable that I should be having issues with this refrigerator less than 3 years later. Shame on you, Maytag!!!

Food freezes in the refrigerator. If I turn it down, the freezer does not freeze. What has happened to the quality of Maytag? This unit is so new. I think I am going to take it back and buy a better brand!

I built a new house in 2006. As part of a builders package, we had all new stainless steel Maytag appliances installed. The side by side refrigerator compressor stopped after 26 months (of course, passed any warranty). No customer support through Maytag and as previously posted very scripted responses. Maytag microwave handle has broken off several times, the glass seal in the oven door was compromised and the inside glass is stained - most recently the on-going issue with my Maytag dishwasher model mdb5601. Ive already replaced the handle /door latch assembly twice and am confronted with the current dilemma if I should replace the control panel that now appears not to be working. It goes without saying that I will never purchase Maytag products again. However, I am not in a position to replace what are fairly new products. That being said, I am reluctant to purchase costly replacement parts given their poor performance and ratings as mentioned in this thread.

Re: refrigerator model # MBF2258XEB1. The above-referenced refrigerator was purchased in 2011 from Home Depot. We paid over $1,000.00 thinking we were buying a good product. Right now the bottom freezer is working but the refrigerator is not cooling. An appliance repairman cleaned out the defroster part, but that did not resolve the problem. He said it was a compressor/valve gas line problem. I cannot afford to spend hundreds of dollars to have this repaired. Even though the warranty has expired, I believe that Maytag should pay the cost of the repair. This is VERY inconvenient and frustrating.

Bought va washer. Trying to upgrade. Water fills about 1/3 of way even on bulky setting. Supposed to be high efficiency. Detergent does not get all the way out because there is no enough water. Have to put it through 2 rinse cycles. Worst machine. Design is flawed. Clothes all wrinkled. I cant afford to buy clothes and have them ruined. Man must have designed. Hate the washer. Im poor and they want take it back... want my money back. I cant buy washer every day. I will keep on complaining. No customer service. People just put you off. It is a Centennial high efficiency. A piece of junk.

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.

Angie from WFCC-PREFERRED APPLIANCE REPAIR had the wiring harness delivered to her personal address and then came out and installed it that same afternoon past 5pm to ensure I had a working stove. She explained what had happened with the parts delivery mixups and also delivered a $100 gift card. Very happy to have my range working and all has turned out well. I am a long time Maytag customer and its great to have all my appliances back.

Within the first 2 years, the dryer stopped heating. After a $300, a few parts and a few attempts to repair the dryer worked again. The sensor still kept saying check the vent and we gave up and removed the outside vent cover. Works great now. The washer worked great until year 4 when it began to sound like a helicopter. It got so bad that it literally hurt my ears and could be heard outside. It also leaked. Called repairman and they couldnt even remove the drum because it had rusted solid. After a total of 4 years we are replacing the set. Do not WASTE your money!

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

Purchased Maytag washer/dryer in November 2016. Have been dissatisfied ever since. Dryer doesnt dry clothes completely after 90 minutes on high setting. Washer leaves white residue on clothes. Noticeable on dark items. Hardly any water on deep water wash cycle. Bedding just makes a big rolled ball. White powdery residue doesnt come off easily. Rewash, dryer, brushing. Ruining my clothes. Service has been out and they dont appear to know how to correct problem. Maytag doesnt know what problem is and their engineering staff hasnt provided any information on how to fix. Maytag seems very disinterested in helping. They just thank you for being a loyal customer. Not anymore. The attached pictures were taken March 11, 2018.

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

We purchased a Maytag refrigerator with bottom freezer and French doors, in March of 2015, Model No. MFF2258DEM00. Its adjustable shelves and adjustable door bins were big points in its favor, at least in my eyes. So far both the fridge and freezer cool fine. The automatic ice maker was never connected, so we obviously have had no problems there. However, within a few months of purchase the bar that supports--and provides tracks for--the vegetable and fruit bins broke. It was replaced, but within another few months it had broken again.This is a DESIGN DEFECT that wont be remedied by replacing the item. The bar, which is plastic, hangs from a thin lip about 1/2 long by 1/8 thick. Thats way too flimsy to support the weight of one bin, much less two. There is no way to repair the bar. The entire assemblage needs to be redesigned and remade from sturdier material. Its not simply the inconvenience of having bins that dont operate smoothly. With their track broken, the bins rest on the glass top of the meat and cheese drawer--and threaten to break that. Theyve already caused the door to that drawer to crack.

I bought a new washer and dryer from Clarks Appliance on North Monroe St.,Tallahassee, FL. I do not like the washer. It is a top loader and has a lock on the lid. The pause button is supposed to let you open and then is supposed to continue the wash. But it releases all the water and shuts down. I asked to return the washer because I have had it only three weeks. They wont take it back. So now I would like to trade or sell it.

Besides the fact that it barely agitates or turns over the clothes even on deep fill (which we need every time otherwise a whole HE cycle goes and the top clothes remain DRY), the oh-so-fancy power button stopped working at less than 2 yo! And guess what, because it is not a button or knob, but control panel sensor button you hover over to turn on, the fix is to replace the $400 little control panel box. On a $600 terrible washing machine! We trashed it and bought something else without a faulty button system. Very unhappy. Do not buy this.

Washer sounds like gearing is broken, is noisy during operation, various combinations of options dont work, appearance of only one agitation cycle combination on washer, just many settings but all with the same response; dryer does not timely dry clothes, all settings default to the same palpable heat temperature; clothes take much longer to dry in new dryer than they did in old Maytag. Newer Maytag set appears to be secondhand garbage sold as new by Menards. Company unresponsive to complaints.

I purchased a Maytag Bravos HE top load washing machine from Sears in 2011. In January 2015, the machine stops at the spin cycle and wont continue the full process. The lid light comes on and blinks red. The machine made a loud grinding noise. A technician from Sears has been to my home 4 times in a month but unable to fix the problem. I have to take my clothes to the outside laundry. I have a protection warranty but it ends in a week. Im frustrated. Maytag Bravos sucks.

I bought a Maytag Commercial Technology Washer and a Bravos XL MCT Maytag Commercial Technology Dryer in July 2018. On April 14, 2020 the control board went out and Maytag will not replace it. It’s going to cost $463.00 to get it repaired. I do not like this washer because it does not fill with enough water to get my clothes clean even with the deep fill cycle turned on. My clothes still smell nasty after they are dried with scented dry sheets. I will never buy another Maytag product, because they are cheap made. Maytag advertises as American made. Fact is they are assembled in America but the parts come from China and Thailand.

I have had Maytags for 20 years and never have been disappointed before I bought the Centennial and it is junk. It doesnt even put enough water in to wash the clothes. After it breaks, I will never buy Maytag again. When did you guys start going down the drain literally? My clothes do not get cleaned. I live in the country and we all get dirty. We need a dependable washer and dont even get me started on the dryer. I thought maybe you would care enough to know.

On May 23, 2009, I purchased a Maytag bottom mount refrigerator even though I knew that Maytag had many problems with this product and others. I innocently thought that by the year 2009, all their problems would have been taken care of - I was wrong. On April 2, 2011, the freezer part of the refrigerator was not defrosting. I had to make a service call to replace the control board. On March 3, 2013, the regular part of the refrigerator was not cooling. I had to make a service call to replace the control board.Complaining to Whirlpool is a waste of time. The best answer I have received is, I am sorry. There is no end to the garbage Whirlpool is manufacturing and by my experience they dont care. Why dont we, the consumers, hire a lawyer and start a class action suit to let Whirlpool know we are fed up with being ripped off?

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

We have had this refrigerator since January 2011. All was OK for 18 months. Then the lid to the deli drawer fell off, the plastic bar that holds the two drawers up broke (weve had to use roof shingles to prop them up) and another one of the plastic pieces crumbled. Now the ice maker wont work and the refrigerator makes a loud ticking noise. There are only two older adults here and we have not treated this appliance roughly. After reading all the complaints on this site, Im wondering if any of it is worth fixing. My GE refrigerator worked for almost 20 years.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

Purchased this oven at Lowes on 2/8/2018 for $1925. Worked good until my wife cleaned the lower oven on 11/22/2019. The next morning the oven was locked and nothing would work. We called for service and the repair bill was $194.55. I told the repairman that the oven had a 10 year warranty on it, one year on everything and the rest on the parts only. He said no, and showed me in the warranty book that it only covered two parts. Which was not the two parts he had to replace. If you purchase a oven with self-clean feature, I would recommend that you do not use it.

Our washer/dryer combination (2005 Maytag Neptune MLE2000AZW) has given us nothing but problems. The main problem is the stink from the washer. The unit is no longer usable and we are searching for a top loading unit to fit in the space. I am so angry - how did this piece of junk ever pass Maytags quality control?

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

Purchased this Whirlpool made Maytag Stainless Steel dishwasher Feb 2013. By Jan 2017 the washer was no longer operational. Due to poor factory design the touch pad wiring harness was crushed during the initial assembly. The harness is routed behind the touch pad/pull handle faceplate in the door. The factory design provided no clearance for the harness. Obviously after little use (opening and closing of the door) the pinched portion of the harness behind the pull handle becomes compromised causing the ELECTRICAL SHORT.I phoned Whirlpool the maker of the Maytag Stainless Steel Dishwasher for assistance, all they offered was a repair plan in excess of $300.00. I purchased this supposedly quality American Made Whirlpool product as well as a range, microwave, washer and dryer in the spirit of supporting US labor. Now Im stuck with a dishwasher that has an ELECTRICAL SHORT, possibly a FIRE HAZARD and Whirlpool trying to milk me for more money. Please think twice before purchasing anything from this Michigan based company.

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

The Maytag Bravos XL washing machine has a difficult time getting clothes clean. The glass top allows a person to watch the clothing being washed. After one watches this for 5 minutes, it is quite clear that the clothes are not being washed properly. Clothes frequently end up dirty at the end of the wash cycles. I personally believe the design of the agitator is so poor that it is not capable of moving the clothing around to come clean. The tub is a large 4.5 cubic foot capacity, but because it uses so little water it simply doesnt function as advertised. Often there is residue on clothing, simple stains like dirt marks dont get removed. In addition to poor cleaning, the spin cycle is simply bizarre; clothes are twisted to the point that the wrinkles created during this cycle will not come out during the dryer phase of laundry work. I am completely unsatisfied with my purchase and regret not researching this more prior to purchase. I am baffled that this product could actually make it through quality control at Maytag. I have had one service call under warranty to fix the lid not locking. This repair was completed with satisfaction.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

I bought this machine about a yr ago. My clothes come out so dirty white spots all over my clothes. Now my bills are higher. Because I cannot afford another washing machine I have to bring them to the laundromat. I saved my money a long time to buy a washer and now I am without one and still paying for this piece of tin that does not work... If I ever get a chance to buy another one it will not be a Maytag. Trust me never never never again!!!!!!!!

Like most people with this Bravos machine, I am 3 months out of warranty and the ball bearing is trash. When the wash goes into spin cycle, it makes a loud clicking noise and takes a few minutes to start spinning. I called service repair and he told me that it was the ball bearing and to talk with them as he has dealt with quite a few high end machines from Maytag that are breaking down after warranty. I should have realized there was a problem when we kept coming up with white spots on our clean laundry and would have to re-rinse clean clothes. This kind of defeats the water saver that is advertised with the machine.Do not buy this product. For a high end washer and dryer, there are many problems. Maybe that is why the Maytag guy is not shown sleeping in commercials any longer. Hes too busy fixing all these machines. Btw, they wont cover the part even though I offered to pay for the service. The best they can do is give me 25% off. Yippee! I cant wait for the other problems to hit me like everyone else.

This washer is the WORST washer we have ever owned. I should have returned it when I attempted and Lowes talked me into keeping, stating I was just overfilling. I put only a few items and the jeans came out with dirt still all over them!! I have photos. Pathetic. Not enough water, not enough agitation. DO NOT waste your money!

I bought a (Maytag brand) Whirlpool washer but it didnt clean clothes, so I had a repairman out. He ran it through their test and agreed that my clothes had lint, pet hair, and dirt on them, and said that was as good as it was going to get. No one called back from Whirlpool. I called them and a second repairman came out, but it was the same story. I got the same repairman back out again after several calls to Whirlpool and listened while he called in and answered questions from Whirlpool - Is she using HE laundry soap, etc. - the same things they asked me. I bought the machine because it was supposed to have one of the largest capacities available. I stood there while the repairman told them that the clothes hanging to dry were covered in lint, dirty, and extremely wrinkled because they twist into a big knot in the machine, among others. No one called back again, so I called them. The service representative told me that I was loading the machine wrong, I was not using the right soap, and that the report they got from the repairman stated that the machine was working as intended. I told them that I was standing there as the repairman told them that my laundry was not clean. They told me that it was not what their record stated. I thought washing machines were supposed to get laundry clean and get the smell of body odor out. They suggested that I use the bulky setting, so I asked them if I should have to use the bulky setting for a load of underwear. They said that the machine was working as intended, but I wanted to have someone else come back out. The appointment was scheduled, but then the repair company called me and asked if I was aware that I would have to pay for the service call. I explained that there must be some kind of mistake because it was a new machine. She told me that Whirlpool had been doing this for a while and they werent sending out repair techs anymore without notifying the customer, and that Whirlpool has been doing it as standard practice for some time now. I requested a written statement from Whirlpool about the incidents but I was refused.

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

I own a Maytag MDB9150AWB dishwasher which isnt covered under current recalls. Yesterday, I heard a loud pop sound, and it stopped working (also popped the circuit breaker). After taking the door apart, we found burnt wires at the bottom of the door close to where they bend to go under the dishwasher.I called Maytag to find out if they would do anything, since this seemed like a defect in the materials used. They wont offer anything!

This has been the worst washing machine I have ever owned!!! Purchased 3 years ago and this is the 3rd time the bearings dont work again. It make loud clanking noises. Then fails to spin at all. The first time it broke was the 1st year we owned it. It is sitting in our hallway and I can hardly wait for it to leave my house. Talked to the local appliance dealer and they never recommends these washers. I told dealer I must have gotten a lemon. He replied that it wasnt a lemon, that the machine tubs have gotten so much bigger and they have needed to upgrade the bearing system and are unwilling to do it. Dealer has highly recommended the Speed Queen. Based on the stellar reviews that is what will be coming to our house today. I can hardly wait. I know, its just a washing machine but frustration has overcome me. The Speed Queen has no plastic parts. We went with the knob style as opposed to the electronic push buttons. Less to go wrong. The warranty on the Speed Queen is top of the line, 5-year parts and labor. The salesperson didnt even try to sell me a warranty. No need to. Speed Queen stands by their product. I only recommend the Maytag Bravo XL if you dont have enough stress in your life.

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

Although this refrigerator is 10 yrs old it really performs well. I like the ice maker as it hardly ever hangs up, the freezer works great and the refrigerator part is really super in the veg drawer and the meat and cheese drawer. All in all this was a great buy.

I bought a washer and dryer a few months ago from Home Depot Maytag. My clothes do not come out wrinkle-free. They are very wrinkled, to the point where I have to iron the perma press. The dryer I just got rid of was 30 years old, and always got the wrinkles out of the clothes. So I am very disappointed in the way yours works. I dont know what you can do, but this is not good. Thank you.

Dryer doesn’t dry any size load in one cycle regardless of settings. Mysteriously, it triggers a message to check the lint filter and line when running a small load with nothing blocking the venting system. It never happens on large loads which would block more of the air flow. You could get a comparably sized dryer for much less. This not the premium product that you pay for.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

I purchased an automatic dishwasher for $660.00 on or about Aug of 2007 (Mod #MDB6759AWS3 ser # NY3417703). It was a model about to be discontinued however still carried the full one year warranty. After install one year and 28 days it failed. The tech described a faulty computer board and a replacement cost of $885.00, a cost of $215.00 more than it originally cost!! They did offer a warranty of one year after we installed the new part but at a cost of $215.00 more than we originally paid! Maytag promotes their brand as reliable. However I dispute this claim.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

I purchased my Maytag side by side refrigerator 11/2011 and by 3/2012 the compressor went out flooding my pool house floor. Maytag replaced the entire fridge because I was only a few months old. I bought the 2 year extended warranty, went down to the pool house (which has central heat and air) and the compressor has gone out again! The results leaving my baseboards molded! My warranty went out 3/17/2015 and Maytag is helping NONE! The only thing they have to say is you can buy a new repair one warranty for $363 to repair for one year. I have had this refrigerator for 3.5 years and now this is the second time its gone out! Customer service said, pool house is different than a regular kitchen. I told her that the pool house is 1,000 sq heated/cooled kitchen, bathroom, sitting room. Thats no different than some houses. Why would that make a difference?? My parents have a 30 year old fridge on the back porch thats still running! I will NEVER purchase another MAYTAG product! Stainless side by side with ice maker.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

I purchased this Maytag Washer and Dryer back in 2000 and have never been unhappy. It really gets my clothes clean and uses a lot less water than a top loader. The only issue is that if you do not clean it once in a while it will start to smell, but I have a cleaner I use every month and so far (knock on wood) it doesnt smell mildewy.

We had a Whirlpool dishwasher for 24 years, and when it was time to purchase a new one, I did a lot of research before choosing our Maytag. Reviews by other consumers who had purchased dishwashers was very helpful in making our decision, and we have had no problems in the almost 18 months that we have had this dishwasher. It is very quiet. It washes and dries the dishes with no streaks, although I wash off the dishes before loading them. It provides 5 cycles and 4 options and lights blink, when the washing and drying cycles are complete. I would recommend the Maytag, Model #MDB4949SHBO wholeheartedly.

I purchased a Maytag refrigerator about two years ago because of the Maytag quality hype. The ice maker has been leaking almost from day one and I need to clear out the ice from the bottom of the freezer every few weeks. Now the thing has quit cooling all together. I contacted the Maytag website and they recommended a local authorized repair firm. I took a day off work to meet the service provider. After checking the fridge they informed me that the problem was with the sealed system and that they could not work on it, and that I would need to contact Maytag to get a real Maytag repair person to come and fix the thing (right back where I started). They were however more than happy to charge me $70.00 for a service call. I tried the Maytag 1 800 number which was a nightmare and it finally hung up on me. I then went back to the website and managed to get a service appointment in two weeks (had to wait for a Saturday appointment because I cant afford to take another day off work). I just hope that this time it will actually be someone who can fix the thing and not charge me just to refer me back to Maytag again. I am not happy with the so called Maytag quality or their BS methods for providing service. Caveat Emptor if you are contemplating a Maytag appliance.

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

I purchased a Maytag washer on 7/23/11 from HHGregg. The salesperson told us they would highly recommend the new (HE) washer and said that everyone will start selling these only. So I bought your Maytag HE washer Centennial commercial brand. My complaint is my clothes dont seem to get clean. I have started putting less clothes in each load to see if that would help and it does not seem to help. When my clothes still come out smelling like my perfume and there are dry spots on my clothes, this tells me my clothes are not getting cleaned. I also have very sensitive skin. If my clothes were not rinsed good enough, I itch very bad. I called the store I bought this at and the salesperson I spoke with also said there were other complaints about HE washers. I wish I would have never bought a (HE) washer.

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

Maytag Bravo XL top load water saver - Purchased this two years ago. This is the worst washer I have spent my hard earned money on. It has ripped clothes, always leaves a lint and soap film on the cloths. We have to re-rinse two to three times especially on black and brown dark clothes. I have raised 7 kids. In the past Maytag has always been the best. I spent a bundle for the matching set and we have to suck it up and buy another set. We wouldnt feel right selling this set to anyone knowing the faulty sales pitch we were mislead into buying this brand. Purchased from Sears. Sears chose not to offer any help in replacing with a different brand.

The Bravo HE Washer was a cheap piece of garbage and I am very surprised Maytag put its name on it. It broke down exactly one year after the warranty went. It did not ever clean clothes properly and all stains remained even when you spot clean first and double rinse. Maytag basically ripped us all off and somebody should start a class action lawsuit for this thing they call a washing machine! What a joke! I wont repair it. It will just fall apart again. Im not stupid. I know this is how they pay their employees doing house calls! So now, I have to go to garage sales and look for one made in the 1970s because that is when machines were made in the USA and things were built to last, not this crud. Maytag should be ashamed. It is time for them to close its doors. Sorry but its true. They are just crooks now selling crud that falls apart! They owe me a full refund.

I wish I had never bought a Maytag refrigerator! Nothing but problems. The ice maker does not work, water leaked 3 times onto our wood floor. Finally, I disconnected the control panel so I have an ice/water dispenser that is useless just like the refrigerator. I dont think the Maytag man is sitting around from lack of work, maybe laziness. Dont buy a Maytag.

Maytag Bravos 300 Electric Dryer - Purchased dryer 2011 and a computer part went out and Maytag wants $418.66 for a computer part. This dryer was used only 6 months a year. Poor attitude about repairing from Maytag and they would not do anything to make us happy with product. A dryer that goes out in 3 years is robbery. Maytag should repair and make customers happy but they just dont care. Anyone who buys a Maytag or Whirlpool product should have their heads examined. I tried to talk sense to Maytag representative but to no avail. I am now going to make sure all of southern Indiana knows of my problem with this product. Those who know me know I have the ability to contact thousands of southern Indiana and Louisville residents.

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

We spent over $1,200 on a Maytag washer on 12/2015 and it did not work properly. The door got locked, had a couple loads moldy because we could not get it open. Didnt drain either. Maytag had someone come look at it 3 times and it still didnt work. Called Maytag and now they told me that they cant do anything about it because is not under their 1 year guarantee. And of course they are very sorry for my unfortunate inconvenience. I thought they had a good honest reputation but... Im just disappointed!

I innocently purchased cash from BrandsMart a Maytag French refrigerator MF12665XEM 7, serial #K22311026 in 06/30/2012 in Boca Raton, FL. I assumed I had bought the last fridge I would ever need because it was supposed to be a product that never needs servicing, according to the wide advertising of the bored Maytag repairmen. So I did not buy a warranty. This fridge is completely useless 3.5 years later and I do not have a leg to stand on, Maytag assures me. The only part thats still working is the compressor, which is also the only part that is warranted! Coincidence? What do you think? I cannot afford to replace it. Neither can I afford to fix it.It started with water from the lower freezer pouring out on the kitchen floor. The next few days the cooling element in the upper fridge went, followed by the inability of the fridge to make ice. Then the freezer at the bottom went completely. This appliance was well cared for by me, personally, ever since I bought it. In a week, it was totally gone (with the exception of the compressor). It has been inspected by accredited appliance repairmen who have told me it is gone! Gone? $2200 gone? I am a widow living on SS, now with no fridge. I bought this appliance with what I made from the sale of my house, when they couldnt give them away in 2012. I need a fridge! This is South Florida and temps even now are in the 90s F. I demand satisfaction from Maytag. I was told their very best warranty would have only been for 10 years. Listen, Ive had fridges that have lasted 20 years without any problem.My name is Elaine **. **, Boca Raton, FL. 33434. TEL# **. My e-mail is **. I demand a refund of this $2200 or at least a repair or preferably a replacement of this mess of a fridge. This is wrong! I am a widow and cancer survivor and I deserve better treatment than this! Contact me and tell me what you are going to do to correct this wrong! Or I will go to the press about your non-service and terrible products. I want redress for this injustice!

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

I have a French door fridge Maytag like everyone else. The bottom freezes over and I have to de-ice it. Now the freezer doesnt want to cool. Its 3 years old. Total piece of junk.

In December 2010, we purchased our Maytag Quiet Series dishwasher model #MDBM601AWB3, serial #NY2916421. At first the sanitize light quit working about 6 months ago. Today, September 30, 2012, this piece of crap will not turn on at all. There are no lights on at all. We paid almost $600.00. As far as being quiet, oh yes it is quiet alright! We the consumers are demanding a recall. Look at the complaints! Its a manufacturer defect in these control panels. I will not be forced into buying another dishwasher or a control panel. I want this company to stand up and say theyre sorry and fix this problem for all of us Americans!

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

This one of the worst purchases I have ever made! Paid over $850 in March, 2015 for the Maytag Bravos XL. At first, we experienced leaking and now there is a terrible banging and clanging noise! Had an appliance repairman come to see what was going on. Apparently it needs a hub replacement and bearing replacement. Was told by two companies that it is not cost effective to fix it due to the amount of parts and labor.Aside from this major issue, I never felt that the clothes came out clean. Many times, the clothes would come out with detergent all stuck to the clothes and had to be rewashed. The softener and bleach dispensers are not removable and it is nearly impossible to get all the way into the cup in order to clean the mildew that builds up. The fabric softener dispenser always had gummed up chunks.Called Maytag several times to no avail. Was basically told - too bad its out of warranty. I have never heard of a washer giving out after 3 years! The worst part is that I have searched many places on the Internet and apparently the bearing problem seems to be a common issue with this washer. I purposely bought an American made product and am extremely disappointed in not only this product, but the company as a whole. The customer service department is awful. I will NEVER purchase Maytag or Whirlpool ever again. They lost my business for putting a terrible product on the market and refusing to acknowledge flaws. Interesting that this model is now discontinued, but they refuse to acknowledge the problems. Stay away from Maytag and/or Whirlpool!

I recently bought a home that had a Maytag Neptune set. While they were newer than mine, I sold my Kenmore set, dirt cheap. Last night when I opened the washer door to take the load out, smoke billowed out. Im sick about this. There should be a recall on these washers!

Bought my Maytag washer and dryer as a set in Feb 2011...like many, I did not get the extended warranty, as I thought this was a great brand. Ive had nothing but problems with both. The dryer takes two rounds to dry, the lint filter is wet and rusted. The belt has popped off and needed to be put back on..The washer does not clean very well. Ive replaced the shift actuator because it was not spinning, now it sounds like a turbo jet taking off. And as of a week ago, my washer started leaking underneath. Paid a tech to come look at it and said my motor was done and Im better off buying a new washer and even recommended that I do Not buy Maytag! So I googled Maytag Bravos and seen all the poor reviews and realized I wasnt the only one! My set is 3 years old and its ridiculous that Ive had these issues, as so many has. Extremely disappointed of this brand and I too, will not be buying Maytag ever again!!

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

I have a Maytag MFI2665XEW6. Im getting water on the floor by the bottom draw. It looks like the coil in the back is freezing up and then melting down to the bottom of the freezer and out to the floor. I dont know how to lower the temp on the door panel.

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.

Has had problems with machine being off-balance and clothes getting clean. 3 years and now the machine is broken. Too costly to get repaired. Warranty only covers very specific things. Have had Maytags repair person come out and he did not access the problem properly. What a waste of time and money! Says it needs a very expensive part which with labor and parts cost almost as much as machine.