I have owned this washer for 3 years and purchased it to match the Centennial Dryer and because of its advertised commercial grade components. The washer has just now turned 3 years old and has never been abused but I have been told the drum bearings are going out.

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!

Just bought a washer and my clothes are always left with dust and dirt on them after washing. Called Maytag, they sent a technician over, but he found nothing wrong. Company refuses to do anything about it, including exchanging it for a different model, since weve had it for more than a month. I am extremely dissatisfied since I just lost over a grand on a washer that doesnt actually wash my clothes.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

We purchased this terrible machine 2 years ago. The clothes come out worse than when they went in! White powdery stuff all over darks! I always have to wipe all dark pants down with a wet cloth! Absolute junk! Really bad product! Never buying from this company again!

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

I have had Maytags for 20 years and never have been disappointed before I bought the Centennial and it is junk. It doesnt even put enough water in to wash the clothes. After it breaks, I will never buy Maytag again. When did you guys start going down the drain literally? My clothes do not get cleaned. I live in the country and we all get dirty. We need a dependable washer and dont even get me started on the dryer. I thought maybe you would care enough to know.

I purchased this refrigerator 1 1/2 yrs. ago. The refrigerator stopped getting cold about 3 months after warranty expired. I called Maytag company and told them how disappointed with their product and also how angry I was after spending $1500 only 18 months ago and now it is useless! They kept asking me if I bought the extended warranty and I said I didnt think I would have to after buying a brand new product. And then it breaks so soon!! And now they want me to spend an additional $359 to get the warranty... what a racket! She told me to look under the fridge for leaks. Sorry I cant, Im disabled. She said too bad and would have service man call me but that would be even more expensive. Woops, disconnected.

Purchased a new Maytag dishwasher just under 1 year ago. After a 5 months it started not working. We called the dealer - who gave us a number to call because it was under warranty. We called the number and it took days to get someone to look at it and not fix it. It needed a new part. Its been over a week now and we havent heard anything, and still no working dishwasher. Our last two dishwashers lasted over 18 years. Kenmore and Whirlpool, never had any issues. This is our first Maytag. Service has been snail pace slow. Dont buy a Maytag dishwasher unless you want to spend your life washing dishes.

I purchase the Maytag dishwasher Model: MDB7749SBM from Home Depot in Plano Tx around June of 2013. The start/resume and cancel/drain button lights either flash or wont turn off and keeps trying to restart the wash cycle. I have only had this DW for 1 1/2 years. That’s pathetic! I went through the manual and tried everything it recommended but it didnt work. So far the unit still cleans dishes. Based on all the reviews I have seen on these Maytag dishwashers with the same issue, you would think there would be a recall. All the appliances in my home are Maytags and Whirlpools. Maytag and Whirlpool are now the same company. Depending on how they handle this issue will determine which appliances I buy in the future.

Maytag 18.5 cu ft Bottom Freezer Refrigerator purchased 12/10/12. 1/12/16 the bottom of the freezer had an inch of ice that leaked onto the floor. My plumber chipped away ice and unclogged drains $97.50. 4/19/18) the same $97.50. 5/22/18 an appliance repair business installed a drain kit $148.40. This was his 25th Maytag with the same problem. A whole website has complaints about this problem. I sent a letter to Maytag and they wanted to send out their technician to find out the problem (with a service cost to me). With all these complaints, and a kit to fix it, they already know the problem but refuse to do anything about it. Maytag used to be a reputable company. No more. The customer service said I should have bought an extended warranty. I said a $1400 refrigerator should last longer than 3 years (the first leaking occurrence). I will never buy a Maytag product (nor Whirlpool that makes it).

I bought a Maytag Bravo washer and dryer 18 months ago. While taking clothes out of my washer, I noticed that the plastic collar above the washtub was shredding around the edges. I called the manufacturer about it. Because it was more than 12 months old, they refused to do anything about it. I feel that shouldnt happen so soon after purchase. Im a single person and dont do that much laundry. The piece should be made of something more durable. I will never buy another Maytag product. Is there anything further I can do to pursue this?

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

MY 8 year old LG front load washing machine died late in 2019. I bought a new front loading MAYTAG machine from a local big box store. It was delivered and set up for me. I had always thought Maytag was a well made product. I wanted to stay with the LG machine, however NO local Repair Service Companies would service it! I was told LG and Samsung were substandard products. (My 9 year old LG clothes dryer is still in good condition).I am truly sorry to say the MAYTAG washer is dreadful. The door locks and cannot be opened the very second you touch the start button. There are fewer wash cycles to chose from. You can never tell if the clothes will spin or be soaked. The door needs to be left ajar and the interior wiped down at end of wash cycle. Etc.. I was ready to call the Store to return the machine - I should have - but I like store. The Maytag price was almost $900. I am very dissatisfied.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

I have had may BravosXL washing machine for 5 years and it is now sitting on the porch waiting to go to the landfill. It has not worked properly since day one, did not clean the clothes properly and even left dry spots where the fabric didnt get washed. Approximately 6 months ago it started making a loud noise while spinning. This week it literally exploded and there was water and oil everywhere, lifting the floor in the laundry room. I am shocked that Maytag would attach their name to such a poor product.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

After two years of light use of Maytag Washer 300 Series (MHWE300VW13), it stopped working. I bought Maytag Repair Plan Plus One on Oct. 8, 2012. I scheduled a service appointment on the 9th of October and was told the broken part needed to be backordered and that I should get the parts on November 5th. I have waited for almost one month. Today is November 6th and I received an email and was told I will have to wait another month! Am I in America? There are so many complaints about Maytag washers online. Can the consumer be protected? Am I complaining to the air here?!

Bought a nice looking Maytag fridge 2 years ago. For the past 6 months it has been leaking all over the kitchen floor. Most recently it has started leaking every 2 days. It is so frustrating as well as extremely dangerous! Both my younger kids have slipped and fell because of the slippery floor. We now have to keep a towel there all the time.Please let me know if there is a product recall. Not the Maytag we used to have. My parents bought all their Maytag appliances when they got married and they lasted over 30 years! This is why I bought the Maytag fridge... not sure of the quality now.

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

I bought the Maytag because of its reputation and as a washer it hasnt disappointed me.. It gets my clothes clean with a minimum amount of effort on my part and it doesnt use a lot of water... I love my washer.

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

Our Maytag dishwasher is a work horse. Never a problem just runs and runs. Could be a little quiet quieter. But does a t great job cleaning. I would definitely buy another one and would recommend it to any one.

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

My dog had to be on a special diet to recover from a stomach disorder. I placed 1/3 cup of dog food plus chicken broth and baby food in a bowl. I intended to heat it for seconds. Minutes later, my dog was whining and sneezing. I immediately returned to the kitchen to find the food and bowl were completely charred. The biggest problem however was from the plastic splash guard that melted down. Smoke filled my home. I had to call the fire department. I was coughing and had difficulty breathing. The smell was horrible!The insurance company and I have had thousands of money in restoration cost due to the damage. I was out of my house for weeks and got very sick due to returning to the home that was not remediated properly (allergies and asthma). The microwave was an over the range Maytag MMV4205BA. I would like to find out if the fire was due to a malfunction in the microwave oven. If so, Maytag should be paying for the damages. I still need living room furniture and carpeting replaced due to smoke damage.

This Maytag oven has lasted my mom for over twenty years. Now after her passing the oven is now serving me and my family. Have had it soon to be three years. Just now having to replace one of the eyes.

I bought this washing machine approximately two and a half years ago. I replaced the agitating wash plate three times. After several months, the wash plate will start free spinning from the gear and will spin like a top. It has to be replaced at $140.00 plus the service call. When it was working, it doesnt clean the clothes well. I contacted Maytag numerous times about this problem and they basically gave me a tough luck answer. I just went purchased a old style machine with a tall agitator that will clean like its suppose to. Its a shame Maytag has no compassion to try and compensate customers for the expenses. I also contacted Whirlpool which took over Maytag. My rating is a negative five.

Clothes do not turn over in the wash cycle. The clothes at the bottom get plenty of hard scrubbing from the agitator but the ones at the top barely get wet and never move down to the bottom. Insufficient amount of water enters the tub. The repairman says the washer is working as designed. Neither Maytag or Lowes will take back the washer. Worst appliance Ive ever owned. Bummer!

After seeing all the bad reviews about Maytag I decided to write my review, we purchased a Maytag washer and dryer 1990 when moving into our new home, and we still have the same set. Now it does not have a motherboard which I feel today is the major problem with most appliances. Get away from the motherboards. Turn the machine on and off when its supposed to, or let it run its Cycles. Dont overfill, because this causes wearing motor parts. The dryer belt wore out on the dryer but that was an easy replacement. Im a woman of 64 and get it myself. Maytag I hope that you get back to the plain ol simple washer and dryer because mine is probably going to wear out which I hope not but I would so love to get the same set I got now.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

1. can not get enough water in the Maytag machine to cover the clothes. 2. All of the clothes come out twisted. 3. After watching the machine wash the clothes I notice that agitator did not move all of the clothes down into the water, and that was probably because there was not enough water in the tub. 4. The machine gets out of balance easily and at that time the machine door is locked and you need to push the pause button and wait for it to unlock the door. 5. Its louder than my old Kenmore washer that we have had for 15 years.6. The Maytag dryer does not dry as fast as my old Kenmore dryer that we have had for 15 years.Bottom line is I would not buy another Maytag product. Do your homework.

Had previous Maytag for years. Good, reliable, easily repaired product. Cycle sequencing very recognizable. New washing machines are ridiculously designed. Neither you nor the repairman have any idea what the cycles are or if they are even working as designed. Many cycles start out trying to wash with little or no visible water in the drum (top loader). The clothes come out tied in knots. I now wait for the agitation to start then pause and add water for three to five minutes then restart. What a nuisance. I have called customer care many times and they are courteous but not very helpful. This machine is an engineering nightmare. If I were in charge I would retire the people who dreamt up this contraption and get back to something reasonable before all their credibility is lost FOREVER!!

Front load washer. When load is done. Removing is one long string of clothes... Is a large load washer which I like. But you cannot add any items after you close the door. And you always forget something that needs washing.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

Bought this because of the load capacity and it seemed like it would be a good purchase to help save on water. But worst mistake ever. The water level barely touches the clothes on top. It barely has any water whatsoever. All my dark colored clothes come out with residue. It’s disgusting and cleaning with Affresh does no good either. Very disappointed with the company.

In 2011 we purchased a complete appliance grouping at Home Depot by Maytag to include the dishwasher. For some reason we neglected to purchase an extended warranty on the dishwasher. Lo and behold in 2013 our control panel went bad and the cost to repair it was almost as much as purchasing a new dishwasher. Thinking this was a fluke we were dumb enough to purchase another Maytag from Home Depot due to the loyalty made in the USA. Well here we are 2015 not even a full two years later the control panel started acting funny a few days ago and yesterday just plain old QUIT. Fortunately we were wise enough to purchase an extended warranty plan on this dishwasher so tomorrow we will be calling the repairman. Unfortunately Maytag has never solved the problem that has been occurring for at least 5 years and continues to sell this product to unsuspecting schmucks like us who try to be true to the made in the USA slogan. Shame on Maytag!!! Our model number is MDB7749SBM. Buyers beware.

I paid a lot of money for this washer. It was recommended by a service guy from Sears. It is only 3 years old. I dont think it cleans well at all. Energy efficiency? Not seen on this machine at all. It takes at least an hour for a cycle. It is super loud on the spin cycle. Now it is leaking and has that stagnant odor that front loaders get. Really! Waste of money. Will never buy a Maytag again.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

Electronic control board fried after 3 yrs on Maytag Gemini range - certain buttons on control board would not set for ovens. Called Maytag, said was not covered, past 1 year warranty. Recommended repair shops, all overpriced. The piece cost between $300-500 for a 3 year old stove. Cheapest repairman wanted 90 to install piece. Ordered piece online and replaced it myself with help from YouTube video. Maytag has lousy repair records lately. Of 4 Maytag appliances purchased in 3 yr kitchen remodeling… already had issues with 3 of them. Do not recommend Maytag anymore!

I bought the Maytag stainless steel refrigerator with the top double doors and bottom freezer. I paid $3000 for this thing and the ice maker has broken twice, an ice sheet forms on the bottom of the freezer and the drawers broke due to being cheaply made with plastic. I had the old style refrigerator for 15 years with not one problem. I think these newly made appliances are made crappy! Will never buy a Maytag again!!!!

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

Maytag bravos xl - HORRIBLE at washing and cleaning the clothes. Broke a little after a year... Went to Maytag site, saw that they push 10 yr warranty. Transmission went out... but not covered?? Garbage.

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.

I had my kitchen remodeled less than 4 years ago with a Maytag refrigerator, Bosch dishwasher, and GE stove. I had a 1 year warranty, and purchased additional 2 years. The warranty ran out last year, and the refrigerator is not working. Maytag customer service said all they could offer was 1 year extended warranty for $300. I told them a refrigerator should last longer than 4 years. They agreed, but that is all they did. Ive read other online reviews, and it appears a lot of people are in the same situation (however my fridge is not on a recall list). I will never buy another Maytag product ever! My GE and Bosch appliances are working just fine.

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

We have had our side by side Kenmore for years and it hasnt let us down! We eat mostly fresh food since we cook a lot and we always have plenty of space for our food. We are only a family of 2 though. They say the ice maker is the first to fail and it has not given us any issues for nearly 10 years now! Love Kenmore!

I purchased this $900 Maytag washer from Home Depot in Oct. 2010. Now, after Ive just paid $129 for a service call through their designated repair service, I was informed it will cost $700 to fix this washer. I use the washer on average of three times a week. Its unbelievable that this type of crap is sold by Home Depot and that Maytag warranties will not cover repair as one year has passed.

Come on people are you serious! Im talking about all those people who give this washer great reviews or even mediocre reviews. This washing machine sucks! Thank God for the glass lid so you can see how terrible it washes. No water in this thing. Clothes that sit on the edge of the bowl do not agitate enough to be washed if there was water in the wash cycle. Bleach that you use in your white wash cycle is left over and gets onto your colored cycle if you wash it the color cycle next. I ** you not, mark my words that stains are left on clothes even in a cycle that has lots of water in it. If you think Im high or crazy take a look at your local Home Depot or Lowes store. Check the area for washing machines that are for sale that have been used. You will find this Maytag Bravos XL machine there. They look good and are practically brand new and they will be there for weeks on and because people return them if they get lucky to return them. I called my store and they refuse to take it back and told me to call the manufacturer. I did just that... I called the manufacturer and they told me they can send out a serviceman to check the washing machine. Butt...and a big butt, if they find nothing wrong with the washing machine that I will be charged a service fee. Bunch of **! For all of us that get stuck with this pile of garbage we can thank the tree huggers for trying to save the world with low water consumption water washing machines.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

After two years of dealing with this awful washer, I felt compelled to write a review. I have had $50 rebuilt washing machines, as well as new ones from the bargain aisle. They worked very well for us. But when it was time to purchase a new one, we wanted a washer with a larger capacity and ended up with this boobie prize. Honestly, whoever designed this washing machine should be ashamed. I cannot believe it made it past the testing stage! Blankets and quilts roll into a ball and never get clean, detergent gets trapped inside this ball of doom, the simplest dirt on clothes survive the cycles, and forget trying to clean stains. I scrub them out, then use the rinse cycle. JUST AWFUL!!! Honestly, this is THE WORST and most disappointing purchase I have ever made. Stay away from it.

Unsafe Maytag - We have had lousy service from our last purchase of a Maytag Atlantis washer and dryer. The washer failed after 14 months, and since it was more expensive to repair it, we replaced it. I needed to do a simple repair to the dryer today, and I had to take the front of the machine off. I found the inside too so full of lint. I believe it was only days away from catching fire. The blanket of lint I removed from the top of the heating element appeared to be charred and black, a fire ready to start in my opinion. I will not have this machine repaired. I want this fire trap out of my house. Before you ask, I must add, my wife cleaned the lint trap often. The Maytag Company has not been helpful. I will add that our first set of Maytags gave us many years of good dependable service. What happened to this company?

It seems to be a broken record with other reviews. I had a 2 year old microwave and the door doesnt recognize that its closed. Which means it wont turn on when I close the door. So you have to open and close it maybe 30-50 times and sometimes it works. I call Maytag who schedules a company but doesnt disclose anything about the warranty or service cost. I was thinking it would be a nominal fee since it falls under a 10 year warranty. The company calls and confirms the cost and I recheck with Maytag who said that the warranty only covers parts. So I buy a $300 microwave and have to pay $160 for a service visit because your company made inferior parts. Absolute sham of a company. Buyer Beware...

I purchased a Maytag side-by-side refrigerator in May 2010 to replace a 20-month-old Whirlpool fridge with a dead compressor. The now 14-month-old Maytag has a dead compressor. I have been told by the repairmen that I have come to know that the compressors used in these units are of poor quality and do not last. That must work out well for the appliance industry if consumers must replace a $1,000 + unit every year or two.To Maytags credit, I spoke to customer service and they agreed to cover the parts and labor for the repair even though it is two months past warranty. Maybe I can get another year out of this reliable appliance. I am told that all of the major brand appliances use the same compressor.

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

We have only had this Maytag Washer for 3 1/2 years and the bearings went out. There is just my husband and I in the household and we are retired. We only use the washer once or twice a week. The repairman said the whole tub (inner/outer) would also have to be replaced. We paid $1,126.03 for the machine and it will cost $700 to repair it. Needless to say we will not repair it but will buy another washer. We have always been satisfied with Maytag appliances until now. We probably will not buy another Maytag appliance due to this event.

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

Dishwasher could do better with washing the dishes better and less recycling time. Also, it would be better if it had a self cleaning unit on it.

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

The pulley on the dryer vent keeps falling off due to poor design. We had a repairman fix the problem under warranty, but the dryer was purchased in 2010 and this is the third time it has fallen off. I have taken the dryer apart and repaired it myself, as I am quite capable, but I called Maytag Customer Service to see if there is something else I should do or replace. They told me they never heard of the problem and they would recommend a service man repair it, which would cost me money and It wasnt needed. No updated part was recommended, or any other help at all, for that matter. I am very unhappy with the Maytag products and will never buy anything again.

We bought a Maytag Bravo model top washer recently and have no good things to say about it. The startup time is too long and clothes are coming out with lint all over them now. If the unit could be returned we would do it immediately but we cannot.

Would need 3rd panel for 8-year dishwasher - Either no lights come on the panel or Load done lights, like now. It has happened so many times over the years from about a year after spending a lot of money on a Quality unit. Many times I was able to operate it after turning the breaker off/on or leaving it to sit for a week or so, multiple times! Also, the rubber on the racks did not do so great - peeled and rusty. I did apply rubber repair multiple times, then got new racks at my expense. Several other brands bought over the years lasted 10+ years with no repairs!

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

I have a 4-year old Maytag refrigerator. The back of the top freezer compartment is frosted and frozen, and the bottom refrigerator is now too warm to put food into. I wonder if a lonely non-busy Maytag repairman can come and fix it? Oh wait! Thats the deceptive false advertising that I bought into when I wrongly assumed that these were great appliances. I cant afford to get this fixed and after what Ive read from other peoples experiences, it wouldnt matter anyway. It would just break again anyway. What a joke! Ill unplug it and try replugging it in after it thaws and maybe that will work.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

I bought a new Maytag refrigerator on July 2, 2011. The ice continues to drop after removing your glass. Now you must pick the ice from the floor. Maytag said it has a 10 second delay and will continue to drop ice. Im tired of picking up ice and wiping water from the floor. Who wants a product that leaves a mess?

I purchased a Maytag model # MRT 18 FFFHO1 refrigerator from Home Depot. After 7 months, it stopped cooling (wouldnt cool below 52 degrees). Fortunately, I had taken out a 5-year extended warranty. Thats the good news. The bad news is that after numerous trips by a certified repair man -- and three spring/summer months without reliable refrigeration -- Home Depot promised a refund. Well see.Bottom line: keep looking for a refrigerator that works. I have tried GE, Frigidaire, Maytag and Sanyo. Since many of these companies are really just one inept cooperation with more names than Frank Abagnale (Catch Me If You Can), let the buyer beware! I would give Home Depot protection plan 5 stars, though. They stayed with me through thick and thin: by emails, phone calls and text messages. However, their protection plan is worth more than Home Depots appliance products -- through no fault of theirs.

My washer is 3 years old, it sounds as though an earthquake is rocking my laundry room during the addition of water, rinse, and spin cycles. Cleanliness only when washed twice, along with the washer stopping at 12 minutes because of UL signal (unbalanced) - this happens even when I have a small load. The dryer does dry clothes however along with tons of Lint stuck to my clothes. I empty the lint screen after EVERY dry cycle. Have had repairman who charged me $70.00 and said he could not fix the washer.

All I can say is, Wow. My Maytag washer and dryer have never needed anything in 21 years of service. Purchased in 1997 at Lowes in Chambersburg, PA. Both work and look like new! Both are top of the line units. Would buy again!

Bought a washer and dryer from Lowes in June of 2016. Have had service on the dryer 3X and washer 1X since. Two person household that uses product a couple times a week. Dryer drum stops rotating / temp control fails / buzzer doesnt work / motor freezes up / washer makes loud banging sound at the end of the cycle every time....sounds like someone is hitting it with a hammer....Today I want a local serviceman to replace the motor but Maytag insists that I have one of their reps come out next Tuesday to examine the product and then go from there. I have been on the phone for 45 minutes trying to get them to pay me $128 for the failed motor that I will send them for inspection. They will not cooperate. They are hiding behind some BS policy. I want to inform you all in case you are contemplating a Maytag purchase. I will not purchase nor will I recommend Maytag to anyone.

I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

I PURCHASED A WALL OVEN ABOUT 4 months ago. Used the self cleaning, oven blew fuse and some other part, had to wait for almost 2 weeks for repair because of self cleaning liner is now peeling and leaving fine particles. Maytag said it was ok, they would not replace, the liner doesnt have a replacement part so Im going to have to buy a new oven to feel safe for my family meal.

I have read all the complaints. I have similar issues with Maytag Bravos. I’m frustrated that modern tech products stink to high heaven, especially when we refer to clean clothes not being cleaned well. The specific issues I keep getting are the following: the LF codes appear and the cold water does not fill so that it wont rinse or drain. I have replaced the defective washers and that helped for one load. I refuse to fix it. Why throw good money out for the same bad product? I’m looking for a no bells and whistles washer or dryer that works. I have issues with the dryer, too. No more Maytag products in the future. Question: Who truly makes a good reliable product nowadays?

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

Maytag Bravos XL MCT (Disposable). Model number MVWB835DW3 Top load washer. I’ve read many of the reviews on the site and feel your frustrations. Let me start by saying, at least you have a choice of products. I’m stationed in Okinawa Japan and have ONE place to buy my appliances and a choice of two machines. Both of them are garbage Maytag products. The first one (model noted above) died after 18 months. NOTHING they could do! The “technician” they sent didn’t have a clue. His answer was to replace the control board. Time to receive part? Up to 30 days. Really! My option? Buy the exact same product. I can’t even describe how screwed over I feel.

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.