Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

I have never had washing machine that caused this many headaches. The point of a machine is to save you time and energy washing by hand. When the cycle is over, the clothes are tightly spun together that we spend half an hour attempting to untie all the clothes that are woven together. The clothes come back to us in knots, or torn because of the rough nature this machine has created. I have never seen anything like this before and would gladly throw this piece of junk out. We are moving and it would create more headaches to deal with this at the moment. I read that the company had severe money problems and it was due to this very issue. I cant believe a company this well known would allow this to ever hit the market! To openly LIE to people and make money off a product that is faulty deserves the karma they get. Please stay away from this company and their rubbish machines they make and then sell. BUYER BEWARE!

Two years ago I bought a matched set of Maytag Neptune washer and dryer. Although I bought really liked the front loading and large capacity, I bought them because they were Maytags. I remember my parents grumbling that they couldnt afford a decent washer or dryer like Maytag and had to settle for Kenmore or some other brand that they figured was inferior. I noticed that they struggled through 20-25 years of maintenance free use of their inferior appliances. So when I found a pair of Maytag, I thought I had finally arrived. I was 60 years old and I knew this would be the last washer and dryer I would ever have to buy.It is now 2 years later and we developed dryer problems. The repairman found the computer malfunctioning and suggested it would be cheaper to replace than to repair. We asked him to check the washer while he was here and his diagnosis was similar. The drum bearings were gone and probably too expensive to repair. The Maytags are now in some scrap yard and I now have an inferior washer and dryer and I am looking forward to many years of maintenance free struggles. I used to think that Maytag repairmen are the loneliest people because their machines were reliable. I now know that they are lonely because all of the Maytags are garbage and not worth fixing.

We recently purchased a Maytag refrigerator, love it, no problems until the mystery person in my house accidentally broke the slide out door for bottom drawer. So I called Maytag, and with no questions asked they sent me a new part by Purolator! Great customer service makes everything better! Thanks Maytag.

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.

Maytag junk MFW2055FRZ00. We had to replace our reliable 15 year old Frigidaire side by side fridge when it failed due to a compressor failure. We should have pressed the service company to replace it or found someone who would. We were limited in replacement units because of built in cabinets, thus a smaller French door (so we have to open two doors rather than one) Maytag. Perhaps our 30 year old Maytag washer and dryer made us believe Maytag still offers high quality products. We were wrong. Everything about the unit is poorly designed, cheap and flimsy. The freezer drawer pulls out unevenly and the ice maker is primitive. Above all no matter what appliance you choose be sure there exist factory authorized servicers in your area otherwise warranty issues are a problem.

I bought a Maytag washer and dryer so many years ago that I have forgotten when it was. They have performed admirably under trying conditions. Our washer finally needs replacing due to the buildup of scale from our very hard well water. This after about 30 years of good service. Looking to replace them and will probably buy another Maytag set when they go on sale.

Maytag Centennial Washer - Bought washer because of brand name and was that a mistake! This is the Loudest, noisiest, banging clanking washing machine I have ever heard. Every time I do a load of laundry the washer moves a foot from the wall and I have to continually move it back. Needless to say I hover over it all the time when I do laundry. It isnt even 2 years old and we are going to go buy a new machine, AFTER looking at reviews!!!

The washer is very aggressive - it will tangle the clothes and actually tear them if they are thin. There is little control with the speed or water temperature or with the amount of water for a load of clothes.

I tried emailing Maytag but from what I read on consumer reports I doubt Ill get an email back. After our 20 plus year old Kenmore fridge was taken by hurricane Sandy I decided to try Maytag. What junk! We have a bottom freezer and were getting water build up on the bottom under the basket. In order to keep the water from leaking on floor I had to chop the ice out of the bottom every 2 days. My husband got frustrated and took the whole freezer apart only to find all the coils were covered in ice. Soon after that the ice maker stopped working. Tried different things to get it working. We finally took it apart and found the factory did not screw in all the screws on the inside so they fell out on the circuit board and shorted the thing out. Lucky it didnt burn the house down. All I can say is junk! Do not buy!

This was my first Maytag, will definitely be my last. I purchased the combo washer and dryer from Home Depot in 2014. So far it has broken down 4 times needing major parts replaced. The first 2 times it broke within 3 months of owning the machine, so I called Maytag and made very irate complaints and was able to get the 1-year factory warranty extended by another 6 months. This month (May) marks the end of their extended warranty and lo and behold, the machine broke again! I called Maytag again, asking to speak with supervisors instead of customer service reps. They refused to put me on the phone with anyone higher up. I got as far as a customer service manager and she wouldnt budge. Her response was: If the machine breaks again, call us back and we will be happy to review your case at that time. I assured her that the machine would definitely break again, because it is a lemon and has broken 4 times already and wanted satisfaction NOW!! She refused to continue speaking with me and told me to call back if and when the machine breaks again. I am deeply disappointed in Maytag as a company. They had a wonderful reputation way back when, but their customer service department is sorely lacking along with selling a sub-standard product that they will not stand by. I plan on taking this matter further. I am a business owner as well as a single mom, and have no time for broken down machines and nonsense.

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

This is the worse washing machine ever. Wish Id never have bought it. Clothes come out unclean, washer cleaner cycle doesnt work, water level is almost none, etc etc. I could go on and on, you get the picture. Coming here and seeing 100s of negative reviews and complaints many of which I suffer from as well, just clarifies how bad this machine really is. There has got to be a way to bring a class action lawsuit or arbitrary suit against them. Im pretty confident that there are probably 100s more who are dealing with this shoddy washing machine as we all are.

We had purchased a Maytag refrigerator from a local appliance store in May 2012. The fridge was delivered in June and come August 5, 2013, it does not work. First, the temperature of the refrigerator declined drastically causing us to lose over $500 worth of food. Items that were even unopened had to be thrown down the drain. The first call was made to Maytag customer service. They decided to send a technician. Great. The technician came and informed us that it was the refrigerant. WRONG. The second technician comes and states that the compressor is shot and that is why it is not staying cold. Time to order the compressor that is on back order. Shocking. Another week goes by without a fridge. Cut to the third technician who comes and installs the new compressor. Fridge is cool and at about 32 degrees for probably 4 hours. The food goes back in the fridge and the temperature climbs to 70 within minutes. Strike two. Contact Customer Service and demand answers on what can be done. Speak with the first representative named Melinda. If you get her good luck. She states she doesnt care and hangs up. Call back to speak with another representative who is very sweet and compassionate and tries her best to help. Unfortunately, she was unable to do so. Asked to speak with a supervisor and had the displeasure of speaking with Scott. For all the trouble that we have been going through, time wasted, food thrown away, Scott can offer $100. Yeah, okay, nice try. The more we speak with Scott, he ups the ante to $150 and the final offer of $200. I advised Scott that there is someone higher than him that needs to be involved after he told me that he was the highest I could go. Wrong again. Time goes by and nothing happens. We receive a call from Yvette ** that was missed and call her back in the corporate executive office. We have contacted her and left her 4 voice mails and the response has been nothing. Actually, calling her you get her message that she is not available. This is over the span of a week. Nothing. ANOTHER technician is sent to look at the fridge and what was supposed to be a brand new compressor that was installed and states that the fridge is condemned. Well isnt that lovely?! Of course because the parts are made in Brazil and Maytag is charged $15 for them and they charge the consumer $200. There is no reason why they should work. We got in touch with the appliance store who told us that we need to speak with Maytag to ask for our money back because we are NOT taking the same fridge as a replacement. Now, we are plagued with the appliance store not taking our calls, the corporate executives not taking our calls, and a $1300 stainless steel french door paperweight. With a call in to our attorney and the phone poised to be dialing our local news stations, I am not sure of what the next move for Maytag will be. Im sitting here after 21 days of not having a refrigerator hoping that a call and resolution comes soon. My family will NEVER EVER purchase a Maytag appliance again. I wouldnt even purchase Maytag brand toilet paper because Im sure that it would need to have one function and even that function as easy as it is would not work. People, please save yourself the headache and the money and the time of dealing with Maytag, Whirlpool, and Amana. Their customer service does not care about you, their products are crap, and they will swindle you and leave you high and dry. I hope to have some good news about this issue but I can guarantee that nothing good is going to come of this, well, at least for Maytag. Get on your social media and let people know how TERRIBLE this company is. STOP BUYING THEIR PRODUCTS. Sorry Maytag, the buck stops here.

A 14-month-old cabinet dryer required a new motor. I was promised delivery in 3/4 days. Following several calls, all of which resulted in the delivery date being extended to over eight weeks, the same engineer called to install the new motor. He refused to do it as the surrounding paneling had not been removed to give him access to the cabinet. It took another four days for him to return after we called in our builder to remove the panel--three screws and four-minute work. I asked for the warranty to be extended, by way of recognition of Maytags awful service. My request was rejected out of hand and the reasons do not accord with the chronological evidence I hold. I am about to bring a claim in the local County Court.

Worst washer ever. My clothes I have to wash a few times before they all get wet. Not a good washer at all. Has all the bells and whistles. Lets me know when the washer is done or its unbalanced... my washer is crap. Ive had it maybe a year now. I now have to buy another one. Why? Because this one sucks literally... its Maytag commercial technology.

My Maytag refrigerator was purchased from Home Depot less than 3 years ago. It is a French door, bottom freezer draw model #MFI2569VEA1. Every four days, there is a huge puddle of water at the base of the unit and it is starting to ruin my ceramic tiles. I tried the online video solutions to no avail. Home Depot wont repair it, they told me to contact Maytag. Maytag wants me to purchase a $375 warranty, which is 30% of what I paid for the refrigerator. I will never buy a Maytag refrigerator again, or any Maytag product for that matter. They once stood for solid reliability and peace of mind, now you get a piece of junk instead. I cant even sell it on Craigslist if I wanted to because who would want it? If a class action suit is ever initiated, Ill be on board. I hope Consumer Affairs contacts me.

We purchased our Maytag fridge on May 13, 2013. On June 19, 2013, it stopped working. We called Home Depot where we bought the fridge and they told us that we would have to deal with Maytag. What a nightmare. The repair guy came out and ordered a compressor for the fridge. 2 days later, when the compressor came in, the repair guy told us that the fridge was unrepairable. Great, what was I supposed to do with this hunk of metal now? I called Home Depot back, and they ordered me a new fridge, added a five-year warranty for free, and the Store Manager even dropped off a small dorm size fridge for us till our new one came in. Yeah for Home Depot!!!! I would recommend no one ever buy a Maytag product again - what a piece of junk. Their customer service didnt even care; they had the same old story - We will get back with you in 72 hours. Maytag was good when it was built in the US; now its just more China Junk.

Recently May 2019, bought a Maytag Bravos Washer, HE. Its now installed and so disappointed with this product. Not enough water to wash Clothes. Would of taken cashback from Maytag, but cant wait 6 to 8 weeks for cashback. 6 to 8 weeks after they have washer picked up. How long did we want to go without clean clothes, hummm. Problem was looked at by a professional appliance repair company sent by Maytag. His opinion, suggestion was, washer just didnt deliver enough water to wash clothes. I know its HE, suppose to me water miser, but Maytag Bravos just doesnt give enough WATER. How do we get clean cloth like that. As I mentioned in summary, I have added attachment close proximity to add water to washer raising water level to wash Cloth. Yes with proper water it does clean good, JUST NOT A AUTOMATIC WASHER now. Were only two, Rural NB, up to 3-4 washes per week, more when company around.

Purchased Maytag dishwasher July 2013, installed August 2013. Stopped working Oct 2, 2014. Called Maytag and they offered to let me buy a service pan for around $300. No thanks, stupid Im not. I also sent an email. Have not heard back but Im sure Im still out of luck. According to the California class action suit regarding the Maytag control panels, Maytag is saying there are no problems with them. Wish we all had some power to make them see otherwise. Will I ever buy a Maytag product again. No. They would be much better off keeping their customers happy rather than spending tons of money on ads trying to get new customers. Since Maytag is owned by Whirlpool, they will not get my money either.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

I purchased a Maytag refrigerator (MBR2258XES4) from Home Depot in 2012. I bought a five year extended warranty. It started leaking at the bottom. Repairmen said defrost drain clogged not covered! Cost: $180. DO NOT BUY MAYTAG, N.E.W. (Asurion Co.) warranties or Home Depot appliances! This is text book deceptive advertising. At no time did Home Depot associates in Kitchen and Bath departments say that this common design flaw existed and that it was not covered under the N.E.W. Asurion warranty which cost me an an additional $150.00! I am interested in joining a class action lawsuit against Home Depot and Asurion Co (N.E.W.) warranties.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

We bought the Maytag Bravos XL washer 6 years ago when we moved into a new home. We have a large family and after reading many reviews, we settled on this washer. It has served us well for the past 6 years. At the moment, however, it is out of commission. The bearings wore out. My husband ordered new parts and we hope to have our washer up and running again in a couple of days.

Same thing as everyone else. The motherboard/control board, the main face of the washer went out and this part isnt covered on an $800 commercial washer after only 3 years of residential use on a commercial washer. Menards refused to swap it out, saying this is Maytags issue. Maytag boasts their 10 year warranty and labels it right on the motherboard as a 10 year warranty, but the motherboard isnt covered? If the main computer isnt covered, What is covered? Just screws? I called Menards and got nowhere. Called Maytag and held for an hour then had to hang up so I can work. The warranty is extremely misleading and is the reason we bought this particular washer, because it says 10 year parts warranty right there, but Maytag conveniently doesnt consider the main control board a part.

Model #MDB8959SAS1 MAYTAG Dishwasher - purchased in 2014 at Home Depot. First we had to replace the rack adjuster, and after that another part broke. Finally, the electrical control board totally melted and smelled up the house. Fortunately our breaker switch worked and it didnt cause a fire. But Ive read other reviews of this happening with Maytag dishwashers where there was a fire. It now resides at the landfill.

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

I HATE this washer. It had such good reviews before I bought it, but I have never been so disappointed. Doesnt use NEARLY enough water to get anything clean, even when I try deep water wash, bedding, or power wash. You cant switch modes in the middle of a load, and if you leave it paused too long, it drains on you. Ive tried balling everything up as the manufacturer advised. I tried using less detergent, again as advised. Nothing works. Sometimes the clothes on top dont even get wet. Dont waste your money!! If I can find a way to fix my old washer, Im going to do that and throw this thing to the junk heap.

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

We renovated our kitchen in 2008 and installed all Maytag appliances. We had purchased a Maytag dishwasher 3 years prior to the renovation-- that we kept. Well, the dishwasher was the first Maytag appliance to go. After replacing several cheap plastic parts on the dish racks (I resorted to use twist ties at one point to hold the racks together) the racks started to chip and rust, leaving stains on our dishes. The cost to replace the racks was about $150 so we just replaced the dishwasher (with a Bosch - so far, no problems!)Then, a couple of the igniters on our gas cooktop stopped working. Since they were the back burners that we didnt use much, we just used a match to light them and let it go. Next, one of the hinges on the double wall oven door snapped. This is a little concerning because the doors are heavy and will need to be replaced. And the final straw concerns our French door refrigerator. The control panel started flashing wildly and the ice door was opening and closing with a loud clicking sound. Of course this happened on a weekend so I looked online and found hundreds, if not thousands, of similar complaints. So I called Maytag and spent nearly an hour on the phone only to be told that my model number was not one of the recalled ones. I explained that my problem was exactly like the others and was told that the best they could do was offer me 50% off any parts. The service call and shipping would not be covered either. The Maytag representative that I spoke to tried to cheer me up by telling me that at least they had the part I would need in stock, unlike the recalled models. Those parts are discontinued and have to be specially manufactured and have a two month waiting period. The part is about $250 and add to that the shipping and service call and I am sure this is going to cost me several hundred dollars even with the discount on the part. Very, very disappointed. Never again will I buy Maytag, never again!

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

In May 2007, I bought a matching Maytag Neptune washer Model MAH5500 and dryer. I also bought the 3-year extended warranty. Approximately 4 years later, actually 1 month after the warranty had expired, the washer started to get very loud and sounded like a jet engine taking off. I called Brennen Repair Service in Midland, Michigan. The repair man came out and said he did not even have to look at the washer. He knew what was wrong. The bearings were going in the machine. He said I could fix it for approximately $600 or just run it till it quits. I was furious. I called Maytag and explained my issue and was told that there was not a recall and they could do nothing to help me. They even told me that they had not had any complaints of this nature regarding this model. I told them they were full of it. I know of at least 4 people in my family and workplace that have had to replace the Maytag front loader piece of ** washing machine. I think Maytag should stick behind their product with all the complaints out there. I would like to shove my washer through their front window. I previously owned a Maytag washer for 25 years and had not one issue. It ran perfectly. I will never buy another Maytag product nor will anyone in my family. Maytag, you suck. Your service and reputation is appalling.

Purchased this washing machine 4 years ago and every time I do towels, blankets, linens etc. all ends up in the middle of the washer in an unbalanced situation. Cannot clear the balance even when rearranged. I assume this is what happens with all the upright washers now that the center agitation unit has been removed. I have to ask the question of who made this decision to remove the center part? A man who never does laundry?

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

Paid $900 for this side by side stainless steel model 15 years ago. Pros: performance, appearance, simplicity. Cons: none. Only 1 minor repair, and the repairman said this is 1 of only 2 makes he recommends.

I just got the washer 2 days ago! Its horrible! What type of quality assurance dept are running? Or is there even a QA team?? I put a big load and selected Hot & Power wash. There was hardly any water. It was cold. The detergent nor softener never dispensed. This is the worst washer ever!!!

We bought a Maytag Bravos XL assuming that because of the brand name it would be a great machine. WRONG. This washer is truly awful. Every single load of darks comes out covered in soap scum. I always have to rewash every dark load with no soap for a full normal cycle in order to get the scum off. My whites are probably also scummy but often I just throw them in the dryer as I cant see the scum. Its just a very, very poorly designed machine that obviously wasnt tested before they started manufacturing and selling it. Its criminal how Maytag continued to sell this piece of junk, and Ill never trust their brand again.

Purchased a Maytag Dishwasher (Serial # P33706417) in Sep. 2013. In the beginning was working fine. After a year and a half started having problems pushing the button to start, not starting. Had to wait a few hours then hit it again and all the lights would light up and then it would start washing. Then when done, some lights stayed on and never went off. Then a month or 2 later, same problem but only a couple of lights would go on and when done 2 lights would blink continuously. After several months now, none of the lights are working and cant get dishwasher to start. Called a tech and he said the control board and the touchpad were not working. Would cost me over $400 plus shipping, etc. to for new. Very frustrated with Maytag, as we havent even gotten 2 years out of this dishwasher and the 1 year warranty has expired. DONT BUY A MAYTAG!!!

I got a Maytag Bravos 18 months ago and liked it at first. After using the washer for a while my towels were falling apart. Did not connect to the washer at first but I began to notice pulled threads on my towels. Talked to Maytag customer service who said they had never heard of the problem. She did say mix the towels with other clothes to prevent the problem. When I got this machine we had about two dozen good quality towels. Now I am down to maybe a half dozen. Those came from the six my Dad bought us for Christmas and I stashed away. The towels have pulled threads all over and will be completely destroyed soon.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

We purchased the Maytag Bravos XL Washer and Dryer based on the good reviews. This has been the worst appliance purchase we have ever made. The washer had to be replaced on the 3rd day after it was installed due to a motherboard issue. The washer constantly has the UL error code so I cannot leave the house if I am going to wash any clothes - I readjust all the clothing in the washer; however, there is no rhyme or reason to the UL code - just made workmanship.We also have had many issues with the dryer as well. Our clothes stopped drying, the clothes had a mildew smell and the lint was wet even though we religiously clean out the lint element. We researched and found this was a common issue. The belt comes off on these dryers; apparently it happens quite often. We fixed it ourselves - twice- by watching a YouTube video. Now our dryer catch (latch) doesnt work and we have to repair that as well.It is obvious from all the complaints that both of these Maytag machines that there should be a class action lawsuit at this point in time. I will NEVER purchase a Maytag or Whirlpool product - EVER. Whenever anyone asks me for a recommendation I tell them to stay FAR FAR away from both Maytag and Whirlpool products since they are unreliable, have terrible workmanship and the company will not do the right thing and fix the issue and provide refunds to those that have purchased these terrible machines. A washer and dryer is a big investment and should last more than a couple of years. I never had issues with my Kenmore or GE products and wish I still had them. DO NOT PURCHASE ANY PRODUCTS MANUFACTURED BY MAYTAG OR WHIRLPOOL. EVER.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

BUYER BEWARE!!! We purchased a Maytag Dishwasher mdbh979sab1 on November 23, 2012. It is now July 31, 2014. One year and a half and the control panel is not working. Ive looked at estimates online of $450.00 for parts and labor. Customer service is no help at all, nothing they can do. She actually recommended KitchenAid for our next appliance. Maytag has become a terrible brand. We will never buy from them again. By the way, they also made our Jenn Air Oven, which turned itself on a number of times while we were away. 350 degrees. That was a total loss as well. We are filling up landfills with our Maytag/Whirlpool appliances and you will too.

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

We purchased a new Maytag Bravos X washer and dryer from Lowes in June of 2013. After a year and a half of normal use (2 people in the household) the washer needs a new gearbox bearing at a repair cost of $529.00. I called Maytag and spoke to a customer service representative who informed me that there was nothing they could do about it because it was past the one year warranty. I asked to speak with a supervisor who told me they would offer me a 50% discount on the bearing but would not pay for the repair work (the cost of the bearing is approximately $25).Needless to say I will not be having the washer repaired. We will be purchasing a new washer and it WILL NOT be a Maytag, Whirlpool or any other brand made by that company. Its just appalling to think a company like Maytag can scam customers the way they do by producing appliances that are of such poor quality and then offer third rate customer service on top of it. Maytags answer to the whole issue is selling everyone an extended warranty which we all know is as bogus as the companys integrity!!!

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

I purchased a complete Maytag set for my kitchen (fridge, double oven, microwave, dishwasher) from Home Depot on November 22nd 2012. About two months ago I noticed the dishwasher started to glitch here and there, but was still functional. I removed the panel and found that the wiring was completely corroded and would need to be replaced. I put everything back together and have managed to make it almost a month on the same cable. In the mean time, I searched for my receipts, my manuals, and anything else to show my purchase given the 10 YEAR WARRANTY Maytag wants to mention as a sale point. Aside from Home Depot not being able to find my order information to duplicate the receipt, I managed to find where I had ordered my set online and was emailed a copy. Home depot is not involved with the warranty process, unless you purchase the additional warranty. They deferred me to Maytag. I contacted Maytag and was informed that the warranty only covers the stainless internal tub, the racks, and the chopper. Seriously?? So, absolutely NOTHING mechanical about the product past one year.After paying the $699 for the washer, and another 57.99 for installation and kit, I was told by Maytag that I could buy another 1 year warranty that would cover the part, but it would cost me $289, or roughly half the price I paid to get a whole two years out of the dishwasher in the first place. This means I might as well be paying almost $300 a year just to have this product... ridiculous!! Just to buy the part and do the work myself, the part is $172 plus tax/shipping. Since it is only 4 screws and a couple clips holding this thing on, I am likely going to go that route.I have read many people saying similar things about the electronic wire corroding and this appears to be a well known issue with their products. They recommend sealing the entire area using a tube of silicone to help reduce the amount of time it takes to ruin another cable. Very very very poor craftsmanship. Nice racket they have through charging people so much every couple of years for their products!! As my $4000 kitchen appliance set falls apart, I doubt I will ever replace it with another Maytag item.

Just like all the other reviews, the control panel on our 3-year-old dishwasher stopped working. The obvious defect of the product and lack of customer support is unreal. We ended up replacing the Maytag with a Frigidaire. Hopefully it lasts more than three years.

I purchased a Maxima washer and dryer set, along with the pedestals. I had the set delivered to the new house the kids and I are moving into, but didnt use it for 2 weeks as we had not moved in yet. Guess what? I used the dryer 1 time and the drum stopped working. I called and got tech out. Motor is not working. They had to order a replacement, then back again to replace. Guess what? Less than a year later, same thing happened and another two visits from tech, motor was replaced. Get the pattern? And now, less than 2 years after purchasing and another two visits, motor drive and control board were ordered. They have not been installed yet. I have sent emails to Maytag and on the second one, they actually called me. The lady didnt think there was anything wrong with the fact that it broke after the FIRST use. Her reply to me was, But we fixed it... At this point, 2 years and 6 tech visits, three new motors and a control board, not to mention my time taking off from work and being held hostage waiting for the tech, they could have replaced it and saved themselves some money. They have lost all credibility. I am about to try regular mail to a supervisor. Wish me luck.

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

Purchased 6-1/2 years ago when we had kitchen remodeled. Bought the stainless steel with stainless interior. The interior design was perfect for placing the various dishes, glassware and utensils. There are a number of settings to choose from, however, we tend to use it as more of a sanitizer so the light or normal wash are the preferred and dont use the heat-dry as we dont find it necessary. Very pleased with the quietness of the cycles and have no regrets with our purchase.

I purchased my machine on June 2, 2021 and it was delivered and installed on June 4. I have successfully done two loads of laundry. On June 9, I attempted washing two small bath mats and 2 dish towels. When I returned to the laundry room to place the load in my dryer, I found the the items in soapy water. I tried many times to reset the load with no success. On June 10th I called Maytag’s customer service and spoke with an associate who walked me through a couple of common quick fixes. These also were unsuccessful. She referred me to warranty service. I will not be able to have my machine repaired until June 23rd! Obviously, if their repair department is so overwhelmed, the products they sell are a piece of junk. I am furious with both the product and the service I have received.

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

I purchase the Maytag Bravos washer & dryer set 3 1/2 years ago brand new. I figured being a Maytag it would last for a long time but nope I was wrong??? I will never buy another Maytag product as long as I live and I will tell all my friends and family not to purchase a Maytag product also!

I bought a Maytag dishwasher to match other appliances in kitchen. Work great, not loud and gets dishes clean. Have owned it for 10 years and have one problem with the door latch. But it was easy and inexpensive to replace.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

Nice refrigerator, but cheaply made. I paid 1800 with tax for my french door Maytag and expected higher durability. It operates well but one worries about breaking drawers made of such thin plastic.

I, too, have had major problems with this Maytag refrigerator! We have experienced everything from a malfunctioning ice maker, flashing control panel, overloaded compressor, erratic freezer (freezes much of the fridge contents), and doors not staying closed/inadvertently popping open. We have owned this fridge since 2007 and have repaired the ice maker and the freezing problems on our own dime. When the clicking sound woke the entire house up at 5 am, I finally decided to post! I realize that appliances are not perfect, and that Maytag had the best of intentions when designing and producing this product, but what really infuriates me is that Maytag has known about this widespread inherent problem since late 2006! Why no recall? Why no notice? Why no assistance? When I called the customer service line this morning, the representative acted like shed never even heard of this fridge having problems - yeah, right. All you have to do is Google the model number or just Maytag fridge panel flashing and clicking problem to discover thousands of similar complaints. I do not fault Maytag for manufacturing a less than perfect appliance, but I do hold them accountable for adequately repairing/replacing such a rampant and unsafe (compressor overload) product! Maybe it is time for a class action. Something needs to be done to protect the consumer from a company that is so slow to correct a long-standing and potentially dangerous problem!

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

Bought a Maytag refrigerator from Home Depot about 2 years ago. Like everyone else we are having leaking problems from the freezer drawers. I wonder if anyone has had it repaired and whether it was repaired

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

I recently bought a home that had a Maytag Neptune set. While they were newer than mine, I sold my Kenmore set, dirt cheap. Last night when I opened the washer door to take the load out, smoke billowed out. Im sick about this. There should be a recall on these washers!

We went to Lowe’s to buy a new washer when our old front loader would’ve cost more to repair than was worth it. This Bravo XL washer is the biggest rip off EVER!! I, like others, have watched with a flashlight & see that most clothes are nowhere NEAR being wet AT ALL!! Let me tell you... I am BEYOND LIVID!! I bought this washer thinking we could wash our comforter at home instead of a laundromat and WHAT A JOKE!! It would never even wet a FOURTH of a queen comforter, let alone the whole thing!! My husband had to actually LEAVE HIS JOB to go home and change because his shirts smelled like a wet animal! People actually were commenting on the smell!!Believe me, we tell EVERYONE how ridiculous this whole energy saving scam is!! AND... I am having to wash clothes TWO and THREE times to get them NEAR smelling normal!! My electric bill and water bill have gone up substantially and again, I AM LIVID BEYOND WORDS!! We spent over $900 for this washer with the extended warranty!!! NEVER EVER AGAIN WOULD I BUY MAYTAG!!! And I have tried EVERYTHING to try to rectify this; I added less detergent, I’ve used the deep water wash, extra rinses. I’ve had the Maytag technician here replacing the circuit board thinking perhaps THAT would give me more water. I sure wish we could all do something for SO MANY of us being taken advantage of!!! Did I mention I’m FUMING?!!?

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!

My $1500 2 yr old Maytag mbf2258Dem refrigerator stopped cooling properly (wont freeze). The icemaker was the slowest I have ever had. That may have been the problem when I bought it. The Maytag Repairman came out and said that even with Maytag sending me a new compressor (under warranty) this unit was not worth fixing. I called Maytag and they said sorry there was nothing they would do. So l looked up every review I could find... and this refrigerator is just bad. Not Worth Fixing. So Maytag deceived me. On the front of the door it says 10 year compressor warranty. Thats a big sales feature! They know that they have a problem. This is one bad company!

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

I purchased a new washer and dryer from Lowes a few months ago. I had my former washer and dryer for nearly 20 years and although the dryer started to have some issues, the washer worked wonderfully. To have a matching set, I decided to purchase both a new washer and dryer. I was told the Maytag Bravos XL model was the top of the line and could handle large loads. After just a few washes I realized this machine does not add enough water to get the top clothes wet and there is no agitator to pull the clothes into the water. I returned to Lowes and was told to use the deep water wash. I tried that and still had clothes coming out from the wash still dry and dirty. Unfortunately Lowes would not take the machines back and I was told to call Maytag. Maytag said there was nothing they could do except send out a technician for a service fee of $98 to help me determine if the machine is functioning correctly. I could not dislike a washer and dryer more! The dryer catches clothes on one of the screws inside and pulls fabric pieces out. This is in my opinion the worst washer dryer set I could imagine having. I will share my experience with as many people as I can to help others avoid making the costly mistake of purchasing a Maytag product. Maytag does not seem to care they have designed and sold a dysfunctional product!

In late March or early April 2010, I purchased a Maytag Microwave from Sears in Ocean, New Jersey. The microwave was installed by Sears technicians on April 9, 2010. The total price for the microwave and installation was $356.53. I specifically purchased the Maytag brand because of Maytags longstanding reputation for quality products with long lifespans.On October 5, 2014, the microwave became inoperative and displayed a code of SE. On or about October 9, 2014, I contacted Maytag Customer Experience Center, via email, and advised them of this problem. I also wrote to Maytag explaining the situation. On October 15, 2014, I was advised via email that, as my warranty had expired, any repairs were my responsibility. I requested that my email be forwarded to Maytags CEO for consideration and review and was advised on October 20, 2014 that a Maytag supervisor would call me within two to three business days (of October 20th). After a follow up letter to the CEO, I was again advised on October 28, 2014, that the microwave was out of warranty and any repairs were my responsibility.I should add that I contacted Maytag Repair Service and was advised that the price of the repair far exceeded the price of the microwave. I feel that four years is not the expected lifespan of a microwave, especially a Maytag, and can only conclude that the Maytag microwave which I purchased was defective. I have purchased less expensive microwaves that have lasted for at least ten years. I got absolutely nowhere with Maytag personnel, found them to be curt and dismissive and would NOT purchase another Maytag product nor would I recommend them. Buyer beware - Maytag is not what it used to be! Very disappointing.

We purchased a washer and dryer, spent in the neighborhood of 1000.00 hard earned $$... extended warranty, the whole enchilada. Maytag. dependable, lonely repair man, ha.. that is just so much stuff. Well anyway it was a Centennial set. What junk. Never really worked that well to begin with. I trashed them both after exhausting all avenues to make it right. Well I got the hair to report the mess to consumer affairs and see if they are what they claim to be. This is more of a warning to all consumers.The stuff you consume today isnt worth the money you pay for it. The money isnt worth the time you spent to earn it. I am gonna try to find a old washer and rebuild it, and a dryer as well. Or just use solar. Best to keep the old stuff repaired and running. I dont know how many people I have spoken to about this problem. Our infrastructure is crumbling. A consumer based economy. Only there is not anyone to service the products we consume... pitiful. I guess my wife will be out back with a tub and washboard before it is all said and done... she will not like it, I guarantee that. I could not even begin to repair the washer. It was a computer operated board that did not work correctly from the beginning. The dude came out from the repair shop and fixed it while still under warranty. It died a slow painful death shortly after that. I disassembled it with a screwdriver and now have potatoes growing in the tub.The dryer has not met the same fate yet. It just sits there, anticipating the moment when I remove it and dissect it with a Sawzall. And I guarantee that day is coming. Do not buy anything from Maytag or its subsidiaries, think long term. We have become a bic lighter economy. I have been on the forefront of that movement. I did not realize it at the time. I do now. and for that I am sorry. I always expect something to work when I need it and if it doesnt, I try to repair it. Cannot fix this stuff now. The support we used to take for granted has been outsourced as well as the production of the product. Bob Dylan said it best in the song union sundown... Thank you and e pluribus unum.

I purchased a Maytag microwave oven on July 22, 2011. It was delivered August 2. Model no. MMV4203DW, serial no. CK01001086. I paid $279 at Lowes Spokane Valley WA. I made a family brand name dinner for six in the original black carton, put the rack into the microwave, followed all the directions as the microwave was new. The carton melted inside and burned a place where the rack had rested. This melted before the time was up. I had followed all the directions. This was the first incident that was a problem. Next incident was a large bag of popcorn (microwave has two settings for popcorn--large or small). This burned the bag black before the allowed automatic setting. Third incident was another bag of popcorn, which resulted to a fire. I tried putting it out with a large lid, which now has permanent black smoke stains. The fire was so hot I could not remove the popcorn bag. I had to use two pancake spatulas to throw it outside where it continued to have flames and burned itself out. The next fire was with a baked potato. This was set for a regular potato setting. This fire was great flames. I tried putting this out with salt and a pan lid. I also removed it with a large metal strainer, an Asian type which is large, and used another spatula to scoop the flaming potato and took it outside while it continued to burn. This time the microwave burned itself out. All lights would not function so I unplugged it from the outlet. I have repeatedly told Ava that I had previously owned a Kenmore convection microwave and the only time I used the rack was when I baked something. She continued to ignore this and said that I used the rack to make popcorn, baked potato, etc.

We have a 4yr old model MFI2665XEM7, just started leaking water every other day. A puddle wipe it up and its gone. Have ice build up on the bottom of freezer. Any suggestions on what to do?

Maytag refrigerator model MFF2558VEM9 purchased in November 2012 from Home Depot for $1329 suddenly would not maintain freezer temperature under high 20s in April 2017 (4 years, 5 months). Repairman says it has coolant leak, probably due to corrosion within the sealed system. Cost to repair - $1500. Repairman says this is a common problem.

CHRISTMAS morning Set oven to 325 for ham. Control board caught fire and burnt wires and burnt inside of rear cover. It got hot enough to char the wood wall behind stove. This could have killed my family on CHRISTMAS.

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

This is a Bravos MTC machine. It is a top load and has an energy star rating. Made in the United States. Impressed by its low water usage and Its ability to clean clothes. This particular model comes with a 10 year limited parts warranty, drive motor and washbasket.

The only reason I am giving 2 stars is because I didnt actually spend my hard earned money buying these machines, they came with our house purchase. At first I was excited to have a good quality washer/dryer... Now I understand why the previous owners left them behind. My complaints are like most of the others on here - takes way too long to do a load because of the stupid water sensor, it doesnt wash loads evenly so everything on top hardly gets wet and washed properly, lint all over our clothes, powder residue left behind even though I set it to 2 rinses, a lot of settings but missing useful ones like quick wash... just all around disappointing. At least one good thing has come out of this and we will not be buying Maytag for our new laundry room. Saying that I have also read so many bad/worrying reviews about Samsung and LG - cant any company make good, reliable, lasting products and stand behind a warranty anymore?!

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

We bought a pair of Maytag Bravo MCT washer and dryer on May 30, 2011. On April 30th our dryer would not turn on. We called the Maytag service where we bought our machine, and were told it was a fried motherboard and would cost approx $600 parts plus labour. For a machine to last less than three years is very unreasonable. Maytag used to have such a good name. That is why we originally went for this brand. We were told by the service tech, that if we opted to buy a new replacement machine they would waive the service call charge. Is this how Maytag keeps selling units?? We bought the higher end units thinking that they would last 10+ years but now it seems Maytag has designed their machines that are disposable. Tisk tisk Maytag. No wonder your service men are lonely... Your sales staff are too busy reselling to loyal customers. Well, you have lost customer with us. We are going to Sears to buy a new dryer made by GE and will sell our Maytag washer on Craigslist and replace it with the matching washer from GE.

Ive read a few reviews and would have to agree. This is the worse washer I have ever purchased. I agree clothes go in dirty and come out dirty. I have to hand wash clothes to get them clean and wont even mention how long it takes a white t shirt to start looking like it was placed in mud vs being placed in a washer. Called Maytag and they said I was loading it wrong even though I was loading it as suggested by the manual. Then they suggested it needed service. I think not after reading these reviews.The irony is that I had called for service on a front loader due to prolonged washing cycles, the repairman was as useful as this MayTag washer. Come to find out I replaced a perfectly functioning washer, intake screen on cold water needed to be cleaned, for this piece of useless metal. I guess since reading that Maytag doesnt value its customers by offering some type of consideration I will replace this piece of crap. Please dont buy the Bravo series. You will be sorry and you will never have whites white again.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

Bought a Maytag HE top load washing machine (Model MVWB765FW) in Jan of 2019. As I write this the repairman is banging away on the machine to replace the gearbox that had gone bad. This is the second time a repairman has been out to work on the machine. The first time was to replace a bad water pump, which was when the machine was about six months old. Maytag would have you believe that Power and Durability Come Standard. So too, apparently, are visits from the repairman. To its credit it does a good job cleaning clothes - when its working. If youre going to buy this machine, I recommend purchasing an extended warranty - youre going to need it.

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.