We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

I purchased the Maytag Neptune set in 2004 and was not informed there was a class action lawsuit and was never notified. When washer quit working, I called Maytag who sold me a $300 service contract. They came out and said they couldnt fix the washer and I needed to buy a new one. I paid a fortune for this piece of junk and now have to spend another $700 to get a new washer. I will never buy Maytag again. How can they get away with selling washers that are on recall and involved in a lawsuit?

Ive been a Maytag consumer since 1980. I bought washer, dryer, refrigerator and a smooth top oven. I replaced the washer and dryer with the Bravos series on November 22, 2011. Everything was fine until 6 weeks ago. The bearing went bad under the drum. 2 techs and 2 weeks later, at the cost of $527 and change spent on repair for a $650.00 machine, I started to look into reviews. Not! Can you say class action lawsuit! The fine gentlemen informed me 5 years ago about the Canada buyout, a local retailer that only sold Maytags. He shut his doors due to the fact that he will not work on junk! Oh well, he was right. 13 months worth of use and Im going to spend that kind of money. Now I understand why the repairman in the commercials retired! Shame on you. Love, crazy Mike.

I own a 2004 Neptune front end washer that Ive dealt with the terrible smell of stagnant water since I got it. Now the motor went and I was told I need a new washer even though the product warranty information clearly states the motor is covered for up to 10 years. The repairman told us that the motor thats in my machine is no longer being manufactured. How is that my fault? I do not have another $800.00 for a new one, which is now not even a lot of money for a washer. Ive already bought 2 washers since I built my home 14 years ago. Its just not right!

We purchased a high end Maytag Dishwasher from Lowes just 2 years ago. Within a year the machine was turning itself on, beeping for no reason, and eventually the functions on the control panel stopped working. When I called Lowes they gave me a number for a repairman who informed me that the cost of a new control panel would be $514 and its a known issue with moisture getting into the control panel. This is unacceptable. There are hundreds of complaints and a class action lawsuit regarding this issue and yet Maytag has done nothing to remedy this situation. I am forced to purchase a new dishwasher and I will never purchase another Maytag product.

Why is it when you wash dark clothes they come out with white spots which looks like soap. I have put very little soap and it still appears. I usually wash in cold water so I tried warm water - same result. I have had a Maytag for a least 40 years never had this problem - what is it I am doing wrong? I have to wash and rinse at least 2 more times. I would appreciate a answer so I can fix this.

I bought a Maytag side by side fridge freezer in 2010 at a cost of £2000. Having come back from a week away it had entirely defrosted spoiling all the contents. An engineer came to look at it but said the fault was unrepairable so he wrote it off. Maytag (Whirlpool) think that it is perfectly ok for a 5 year old fridge freezer costing two grand should now pack up. I, on the other hand, do not... They offered me £700 of the cost of a new Maytag. Joy! I thought. However, this one does not make ice or have chilled water (the principal reason for buying Maytag in the first place). I was then told that this was the ONLY fridge freezer in the entire Maytag or Whirlpool range. Is there nothing else you can do to help? I pleaded. No was the reply. The moral of this story is going posh on an American Fridge freezer is not guarantee that you will get the after sales service that the price would suggest.

I purchased the Maytag Bravo model MGDB950YG on April 22, 2012. It worked great for a while then stopped heating and drying the clothes. After going through the Maytag procedure, a repair person assessed the problem, had to order the part then came back to repair it. But the same thing just happened again! Both Maytag and HHGregg need to go through the appropriate procedures, which leaves me without a dryer for who knows how long this time. Maytag will not do next day service probably because it costs them a little more. I think Maytag should have enough common sense to sometimes make exception to this. Today is Thursday and I cant get an appointment until Monday! I have owned two dryers prior to this which each lasted 10 years plus. I would be much more understanding if I had my appliance for more than 4 months (out of commission 2-3 weeks of the 4 months). Ive never been so disappointed in an appliance!

I purchased an appliance package of washer dryer, refrigerator and dishwasher. All of the appliances needed many repairs. It took four icemakers in the fridge before it actually was fixed. The worst appliance was the dishwasher it was repaired every three months for six years! Washer and dryer died after five years.

Our refrigerator is 2 years old and still under warranty. The ice maker had to be replaced. Now the water leaks on the floor. The deli drawer cover broke and when you get ice out of the ice dispenser it flies all over and goes on the floor. Our dealer has been fairly helpful.

We purchased a Maytag refrigerator model # 1TXEGMYWOO. The refrigerator part froze all of the food in it. We moved the temperature selector to the last place (two notches away from the recommended setting), and the food still froze. The furniture store we purchased it from replaced it with another refrigerator (same model). And that one did the exact same thing. We had to throw out more groceries. Obviously, this model is defective. We are now waiting for the store to replace this one (with a different model and brand). They have been very good about trying to make things right for us. Maytag, however, is a different story. They were very rude and indifferent when I called to complain. Their policy is to repair or replace the part (temperature gauge). I dont want a new part. This is a new product. And I bought it expecting it to work. I have had to throw hundreds of dollars worth of groceries away. I was very disappointed in their attitude. I will not purchase another Maytag item again. They used to have a good reputation. They now sell inferior products and do not stand behind their products.

We bought a New Condo, all New Maytag appliances with a 10 yr. warranty, the microwave is a built-in model. I cant believe weve only been here a year and eight months and it just stop working. We use it for heating and short timed cooking like 1 to 2 minutes. I would think a name brand product would last a lot longer than this. I had an off brand microwave for five years before the condo. A couple of times the microwave door didnt close, I thought I forgot to close it. But after reading your reviews I now realize its one of the defects of the product. I called the Maytag company, they informed me that if a serviceman come out to fix it, it will cost me $180 until they can determine if the cause is something covered by their warranty??? The Home Builders bought Maytag junk and passed us the cost, now Maytag wants me to pay to see if their junk can be fixed??? Wow!!! This is unbelievable!

This machine was purchased two years ago at the Home Depot. I wanted a top loader that was not digital and without a lot of choices. It has been nothing but a headache with every wash. I had a Maytag serviceman come out immediately and he said nothing was wrong. Every wash load I do, has problems. The dark loads are always full of white spots and the towels are torn up. Just bought some new towels and after the first wash, they were ruined. I will never ever buy a Maytag machine. These new He machines are ridiculous! I no longer have a receipt, but the complaint should help consumers in their decision to NOT buy a Maytag machine.

We have a Maytag washer. It is the noisiest washer I have ever seen! It is in the garage as you could not have this washer in a house. The deep water wash is not deep enough. It bangs and knocks VERY loud! There have been times when all of the clothes are not even wet.

This product was purchased in March. In September, the agitator broke off. Thats a new one on me with a washer. Every other one Ive bought tended to last 10 years or so, then something like a motor wore out. It was an obvious design flaw on a topheavy agitator held on by a flimsy plastic sleeve. To make matters worse, their warranty service seems mostly geared to selling extended warranties, necessitated by the poor quality and bad design of their products. So, for a mere $182, I can have it covered for the next six or seven times the agitator breaks. No thanks, Ill figure out how to fix it myself when its no longer under warranty, or just cut my losses by buying another machine, and never another Maytag or Whirlpool product. I had a similar experience with a Whirlpool refrigerator purchased in April 2017, which had a defective module that went fortunately just before it was out of warranty.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

I purchased my Maytag Bravos from Lowes in early 2014. A few weeks after the motherboard fried and Lowes replaced it with a new one. Within my 1 year warranty the new machine had another fried motherboard. Maytag replaced it for free. Now less than a year later the motherboard is fried again. Needless to say I just purchased another washing machine. Definitely not a Maytag. Now I just have to deal with a dysfunctional piece a junk for a few days until I get my new one. After reading all the complaints on here and other sites, Im very disappointed with Maytag. These machines are obviously lemons and any good company should recall them. Mine will be going straight to the junkyard. I have no interest in having a washer that breaks down every 10 months. Definitely the last thing I will ever purchase from Maytag.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

I am renting to own a Maytag refrigerator and it is leaking water on my floor. Runt my floor already - had to replace the floor once. Sent it back to the place where I got it for them to fix it. Paying insurance by the way that isnt worth a crap either cause they wanting to tell me that I left it open at some point or the lights was off at some point. Anyway to make a long story short they gave me the run around and didnt want to fix it. But how do you fight big companies? This was a rental company by the way rent to own so now I have 4 payments left out of 24 at 180.00 each and they still dont want to fix it. I dont know who to be madder at - the rental company or Maytag from selling this piece of junk. But by me renting to own it if any problems occurred they were suppose to fix it. Youre already paying twice the amount to get one cause of credit issues. But thats no reason to double screw someone or should I say triple cause you getting doubled the rental company alone. They need to recall this refrigerator. It has been a lot of complaint and they want to tell you to go behind the refrigerator unstop a line. Well I didnt buy this refrigerator to have to work on pulling it out from the wall every two days to do this procedure. This is crazy. Any one out there looking to buy a refrigerator my advice to you would be do your research and stay away from rental places whatever you do because you will pay twice the amount and they wont stand behind their promise either to fix it as long as you renting from them! And stay away from Maytag!!!

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

Dryer doesn’t dry any size load in one cycle regardless of settings. Mysteriously, it triggers a message to check the lint filter and line when running a small load with nothing blocking the venting system. It never happens on large loads which would block more of the air flow. You could get a comparably sized dryer for much less. This not the premium product that you pay for.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

My Maytag Refrigerator Freezer model MFI2569VEM4 started leaking water into base under bottom freezer door. It then fills up and freezes into solid sheet of ice and overflows and leaks into floor. Ruins Hardwood Floor. BEWARE!!!!! I have now seen several similar complaints online. Mine started doing this less than 2 years old!!!!!

I have a similar story to Patricia. Been without a fridge for over a month. Refrigerator is almost brand new (bought last year) and a service-person has been out three times (going on 4) to fix it. The fixes NEVER work and then they have to order ANOTHER part and I have to wait for the part AND THEN the service person. I should not have to wait once the part comes in. People who have been waiting should be at the TOP of the list. Then again, this is Maytag...probably EVERYONE has been waiting for a fix.Ill never buy a Maytag appliance again unless they give me a new appliance, pay for the apartment sized refrigerator I was forced to buy while I waited--I have 3 children who need fresh food--and replace the $300 worth of groceries that went bad when I was assured the second fix would work (they wont replace my refrigerator--if they do, Ill be satisfied--unless it breaks in less than a year, too).

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

Maytag french door bottom freezer model #MFF2558VEB5 - It stinks to read all the similar problems Ive had with my unit. Purchased Nov 2011. Problems started within a year. First minor, deli drawer broke. I use clear duck tape to operate it and that has been fine. But not acceptable. About a year ago the water leak out of bottom freezer was noticed. The bottom inside is frozen sheet. I break up and manually remove quite often. NOTE: I intentionally do not use, did not install, the ice maker - historically they are poor risk so I dont bother. The ice unit is in the machine but not installed. I assume my water build up which freezes on bottom related to poor design of defrost drain and that is supported by other comments here. I find it disgusting. Live and learn. Its B.S.

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

I bought a French door refrigerator on May 23, 2012. It is now July 9, 2014 and the repairman has told me the compressor is bad. Maytag will do nothing about it because it is out of the 1 year warranty. I am very disappointed because I thought I was buying a quality appliance. I will never purchase another Maytag appliance!

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

We purchased our Maytag Bravos Top Load washer 3 years ago from Home Depot. I have to admit this is the worst washer ever. The clothes does not appear to get clean enough for the amount of time it takes for the clothes to wash. The white clothes look dingy after a wash that I have gotten to the point of pouring an additional amount of bleach in the wash tub. The amount of water that is in the tub is next to nothing, I have to either add additional water or place no more than 20 pieces of clothing in the wash. This is sad and I regret that I wasted my money on this product and I do not recommend it. As soon as I get some extra money to throw away, this washer is going out with the bulk trash.

I purchased this Maytag Washer and Dryer back in 2000 and have never been unhappy. It really gets my clothes clean and uses a lot less water than a top loader. The only issue is that if you do not clean it once in a while it will start to smell, but I have a cleaner I use every month and so far (knock on wood) it doesnt smell mildewy.

I have Control Panel issues with my Maytag Quiet Series 300 Dishwasher. I have saved myself hundreds of dollars! The problem occurs when oxidation or steam shorts out the ribbon on the control board. Simply shut off the power to your dishwasher. Open the 5 or 12 screws on the door. Open the black box where the Control Panel ribbon enters the Control Board, slide the white tension clasp away from ribbon and clean off ribbon using a paper towel. Re-insert ribbon and slide tensioner in place. Replace all parts and turn on power. Job done! I hope you have as much success as I did.

The dishwasher stopped working. The lights on left side of control panel arent working; so, machine wont start. Then machine was purchased in January 2010 for $525 and not including installation. Kim says it will cost $129 for their repairman to come look at it. I wished I had read the list of complaints on your site first.

Ran washer with extra rinse and clothes came out with dry spots. The only way to get clean wash is to wash everything on bulky/sheets. We lost every appliance in Sandy. If I had known the machine was so-called water saver I never would have purchased it. I was in a hurry. I hate the machine.

I bought this washer (Bravos Washer Model MVWX655DW) in June 2017. My wife and I did plenty of research and only complaint at that time was that it made load clicking noises. We bought it and it worked fine but never really filled with water to a level which would cover the clothes. Today I ran a load and brownish water was seeping out from underneath. When I lifted the machine my floor was covered with old stains which looked like oil or grease. I called a local service company and when they found out which model I had they refused to look at it. They said that particular model was known for having issues and when they fixed it, something else would go. They recommended looking online for reviews and calling Maytag.I did so and after explaining the situation to Maytag, they offered to send a technician to look at it to diagnose, not free of charge of course. While I cannot tell you avoid a particular company, I can say MY family will never buy Maytag again. If a washer is well known for having issues within its first 3 years and a company will not try to make it right simply because theres no recall on it I will spend my money elsewhere. Seems fishy that this machine has a ton of 1 star reviews within the last two months and Maytag does not want to eat the cost of servicing their junk.

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

My husband bought me a Maytag washer as a surprise gift. I was so excited to get a Maytag. I will never purchase a Maytag again. I am so tired of washing, rewashing and rerinsing my clothes and still not getting the soap out. I have used every different kind of detergent and used with and without fabric softener. I have also tried cold, warm and hot water. I would rather use more water and get the soap out instead of using more electricity to keep rewashing my clothes and then in the end having to take a wet cloth to get the soap out. Never had to do this with any other washer I owned. Very disappointed as I always thought Maytag was the best.

The washer is not cleaning the laundry. Its a HE my butt. Its been looked at and fixed numerous times. It sits too long and it doesnt really agitate the laundry at all. Laundry is in the exact position when you loaded it when its done. Its the worst washer ever! I can clean the laundry better in the sink!

Bravos XL MCT model#MVWB835DW. Bought this new. After 2 weeks called Maytag. Washing machine did not work. I called off and on for 7 months to Maytag customer service. During this time they tried to do troubleshooting over the phone. Sent technician out. He said that there was problems with this model, that they were working on updates and would get back to me. 10 months after installation, technician came out. Washing machine worked, but still took 2 to 3 hours to wash one load of clothes. Started calling Maytag again. Washer now take 3 to 5 hours to wash load of clothes. You also have to do extra spin cycles (1 to 9 times) to get water out. A year later they send technician out. He tells me that this machine wasnt made to do loads larger than medium, that it cannot wash heavy items such as sweaters, sweatshirts, towels, blankets or comforters. That the normal cycle is not to be used. This is not a working function on this model. It is there because of regulations. Called back to Maytag. They said it was out of warranty and that there was nothing that they could do.

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

I purchased the Maytag Washer & Dryer $1891.14 with Extended Warranties Model numbers: MHW5100DW0 & MED5100DWo. In September 2014 from salesman ** at ABC Warehouse for my Wife as a Wedding Gift. The dryer started malfunctioning toward the end of October, it was randomly flashing a red light indicating Check Lint Screen and when this happens the dryer will lock up not allowing you the OPERATOR to dry your clothing. We ALWAYS check our screen before use and clean after each use, so we found that light to be odd. But anyhow we checked the lint screen and nothing was on it nor was it bent out of shape, everything seemed normal to me & my wife besides the fact we spent $1891.14 on BRAND NEW washer & dryer set thats acting weird. I called ABC Warehouse spoke to **. He said Yeah they do that sometimes, you just gotta MAKE SURE YOU BLOW THOSE THINGS OUT MAN cause they dont like it dirty. I explained to him we keep it clean then he said the screen might be slightly bent. He went on to explain how he seen that happen a lot, I just said uh huh uh huh yeah yeah. So now its like the middle of November and the DRYER Check Lint Screen Light is coming on before every load now and staying on for long periods of time not allowing us to dry our clothing. So I called ** again 2nd week of December this time asking for a new unit. He told me to call the ABC Warehouse Store Warranty Department at 1-800-722-3333. I called and they gave me a number to Master Tech Appliance 1919 Federal Blvd, Ann Arbor, MI 48103 (734) 662-0641. I immediately asked why am I calling technicians instead of new unit when my unit is still under the 1yr factory warranty and in addition too, I have purchased an 5yr extended warranty? They wasnt trying to hear that. So I called Whirlpool 1-800-253-1301 told them the situation and asked for a new unit they said NO and then added by telling me their policies and how many times they can come and attempt to fix my unit before replacing it. I screamed and shouted at them explaining to them that I have spent $1891.14 on a non-working unit for my wife as a wedding gift and I am currently drying my clothes at the local Laundry Mat, they said NO still.So I called Master Tech, they couldnt come out until Feb 3, 2015. My wife took off from work. In the mean time it completely stopped working the first week of January, we had to go to the Laundry Mat every couple days cause we got 4 kids. SMH WOW my wife is pissed, I mean furious. When ** from Master Tech showed up he looked at our unit and said its also not getting hot so he called in to his job they told him to come back and order my parts and to schedule another day to come back. 2 weeks later Master Tech called with the appt. My wife took off from work again but this time they called the day of hours into the day to tell us the parts are on back order and they need to reschedule. My wife was VERY UPSET but we did it anyways. Now remind you are dryer is still out of commission. Were going to the LAUNDRY MAT. Master Tech came 3 days later (my wife took off from work) they literally took our dryer apart (Pics Below) for it to still not work, Master Tech called Whirlpool, Whirlpool told them to order us a NEW SWITCH BOARD. Wow what the hell are you serious? So Master Tech leaves again and orders the SWITCH BOARD. They came 5 days later (My wife took off from work) new switchboard and dryer still not working. Now throughout this whole ordeal Ive been in contact with all 3 companies begging for a new unit and nobody wanted to hear that especially WHIRLPOOL & ABC WAREHOUSE. With Whirlpool knowingly the switchboard didnt fix the issue the first time, they instructed Master Tech back to my home with the same but NEW SWITCHBOARD. LOL WOW I CANT BELIEVE THIS IS HAPPENING TO US. Master Tech schedules yet another day to come by 3-13-2015 & yes my wife took off from work AGAIN just to hear ** say sorry they keep sending me back with the same part and they know its not gonna work but anyhow Im here. He switched out the Switch Board again and still nothing. I called ABC Warehouse and they finally okayed us a new dryer with delivery day of next day, which is today 3-14-2015 and when it arrives THE WHOLE FRONT DOOR IS BENT OFF THE HINGE WOW WOW WOW WOW. Now they say our new will be delivered 3-17-2015 and yes my wife has to take off from work.Updated on April 9, 2015: 3/17/15 ABC Warehouse replaced the 1st broken dryer to only return with another broken dryer, same problem, red check screen light flashing & dryer wont spin. They left here.

My stainless steel french door refrigerator started to rust 4-5 months after purchase. Upon contacting Maytag/Whirlpool I was advised that this is cosmetic and the cosmetic portion of my warranty is expired. I think this is a poor grade of stainless steel and should be recalled and/or replaced. I would not recommend.

My Maytag refrigerator, french door freezer on bottom MFT2976AEMOO has had problems since I bought it. It is with the icemaker in the refrigerator door and freezer. My icemaker has been leaking since we have gotten it dripping water into the refrigerator. The freezer now is not working and all my frozen food thawed out. I am so tired of having workmen coming out to try to repair it. They even took the refrigerator back to the shop and had it for 3 weeks and said it was repaired and told me it was working fine. NOT frozen food, again thawed.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

Bought new Maytag French Door with cooling drawer refrigerator in July, & have had nothing but problems with both product & customer service since. Have already had 2 service calls for the SAME problem. The in-door ice maker/dispenser is a horrendous mess. Place a container below the opening to get ice cubes & ice is sprayed in chunks all over the floor & around the kitchen. To get ice, you have to put the container in direct contact with the opening, & then place a towel over the entire in-door unit to keep ice chunks from spraying all over the floor. The unit has a small flap-door in the ice maker, which must open & close automatically when getting ice, but the flap failed to close, so the ice in the ice maker was melting & the water running into the refrigerator unit & onto the floor. Called warranty repair & they came out & said they fixed the door-flap, but they did not. Ice was still melting & the freezer unit would not even keep ice cream & pastry items frozen solid. Called repair a 2nd time during the first 4 months of ownership, & they came out & replaced the motor to the small door-flap in the in-door ice/water unit. When asked why the freezer would not keep ice cream & pastry items frozen solid, the repairman stated (quote): Freezers dont keep ice cream frozen solid because it has so much sugar in it, its like alcohol. Had no excuse about the pastry issue however. We replaced a 12-year-old Jenn-Air with this piece of junk, but at least the Jenn-Air kept ice & ice cream frozen solid, & the ice maker did not leak & spray ice around the kitchen. Jenn-Air must know something about freezing sugary ice cream, that Maytag/Whirlpool do not understand. Then today we got a notice that Whirlpool had denied payment for the 1st repair visit, even though the unit was only 2 months old then. As such, we expect them to deny payment for this 2nd visit, even though the unit is now only 4 months old. Bad product & sloppy customer service, from a company with ZERO consumer support.

We bought new appliances when we moved to our new house last June (2016). Sears recommended the Maytag 600S pair (HE washer and dryer). We have contacted Sears numerous time to have service people out because many times (75%) the washer does not fill with enough water to wet all the clothes and there is a layer of dry clothes at the top when the wash cycle ends.I do not believe that dry clothes get clean because they are near wet clothes in the washer. But Sears insists this is by design. Some service people tell us that the top loading HE washer will be gone soon because of the complaints but we have to struggle on. Sears seems to hope we just get tired and stop calling as their Customer Service policy. I have to dump 1-2 buckets of water into almost every wash that we do. As a side note, the 600S series has a slanted top rather than the traditional flat top. It looks cute but things fall/roll off of it. It would be nice to put things on top of the washer or dryer while doing the laundry but they roll/slide/fall off. The design is not so cute anymore. Actually, really a stupid idea.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

I bought my refrigerator in May of 2012. Brand new from Home Depot. It is less than 3 years old. Now it is not working. I did not purchase an extended warranty. I never thought in less than 3 years my fridge would stop working. I called Maytag, first question from them was about warranty. So I knew I was screwed. So, basically for $300 they would come out and fix the problem. I only paid $800 for the fridge. I am lost as to why in 3 years my fridge is broke?? Makes no sense to me. So I paid a tech $100 to tell me what was wrong with it. The evaporator is leaking. It is leaking. So the evaporator is bad and I cannot fix myself. So for another $300 they would fix, so a total of $400 in an $800 fridge.I am pissed. I remember my parents having a fridge for over 25 years. Why does Maytag not take responsibility for their problem. The products we buy should last longer than 3 years. It is just a way for them to get us to buy another product. So needless to say, I am one pissed off customer. So let the emailing and letter writing begin.

We have a similar problem to the others who gave reviews on their still NEW Maytag refrigerators. Ours isnt even four years old and several weeks ago we started smelling a chemical odor which then permeated all of our food in the refrigerator and freezer. We didnt buy the extended warranty because we have owned a few refrigerators and all have lasted just fine for 15+ years with no problems. So I called Maytag. They said for a charge of $369.95 they would schedule a repair and would cover the service call, parts and repair and provide an 12 month warranty. If the service call results in an inability to repair the refrigerator, they will refund the full amount of $369.95. So I asked if Maytag would then replace the refrigerator, and the rep said we have to start with the service call before they would discuss any type of refund or replacement. Im angry and disappointed in Maytag. Its a good thing we have a spare refrigerator in our basement. What a hassle! Weve already had to throw away over $100 in food that picked up that horrible odor. Shame on Maytag!

Same problems as everyone else. Water not soaking the clothes, questionable load capacity, shaky (we have engineers in the house so there is no way they did not look for floor evenness as the stores/Maytag will tell you that you may not have done, complete bs) etc. Its absolutely horrible that were all now stuck with such a terrible machine. I really wish I had read these reviews before (I googled the machine earlier but got generic stuff and didnt stumble upon these reviews until much later). Maytag should take responsibility on this as retail stores do not take back appliances unless they are defective. The Bravos is definitely a defective product from the get-go though.

I had my dishwasher for several years. Never had an issue with it. Cleans well and is very quiet which is exactly what I needed. A quiet and effective dishwasher is hard to find. The price was about six hundred dollars. I pursuit at Lowe’s. It was on sale along with a military discount.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

Both the microwave and French door fridge handles are crap. The microwave has completely broken and the fridge is very loose and will soon break, Im sure. Both are less than 5 years old. I will never buy Maytag again.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

I thought I was safe in buying Maytag for all of my appliances in my new kitchen. I bought a double wall oven Maytag MEW6630DDS. I bought it in late 2010 and have had no issues until August of 2018. I rarely use the bottom but used it in August of this year to cook cupcakes. After baking them and leaving the kitchen for a short while I heard a loud explosive, shattering sound. I walked to the kitchen to see that the bottom oven door had shattered into a million pieces. Thank the good Lord that I was not near it. I contacted Maytag to see if there was a reason it would have done this. They said that there had not been a recall. They sent a repairman at no cost to look at it. He came, took it apart and had no reason for why it would have done this. He left it in pieces and said that he was ordering the replacement door. Maytag advised us to turn off the breaker to the oven. After a month without ovens, the repairman called and said that the part had been discontinued. HA! You think?!? It has the potential to explode. It should have been recalled, not just discontinued. Maytag offered us 20% off a new set of $3000 wall ovens or $150 to pick ours up for disposal. Talk about saving the company money and screwing over the unlucky recipient of a defective product. They ought to be ashamed. I am going to have to replace the broken glass with aftermarket glass. What is going to happen when I use the self cleaning option? What happens when the top door explodes. I am scared to use my very expensive wall ovens that I thought would last at least 10 years. Shaneka at Whirlpool said that people have appliances fail all the time and just have to buy replacements. Do all of them have to replace ovens because doors explode for no reason? I am not the only one this has happened to. I have found several other complaints of this on the internet. Why did they discontinue these door? I wonder.

Purchased a Maytag dishwasher in 2009 then had it repaired for a leak in 2010 (just past the 12-month warranty); next another leak in Nov 2013 so purchased another Maytag as repair appliance company said it wasnt worth fixing. Now in Feb 2015 it is leaking Again! So 2 dishwashers and 1 repair in 5 years! Both were purchased from Home Depot. I will Never buy a Maytag product again.

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

We purchased this washer (MHW05500FWD) and dryer set in 09/26/2016 and have had nothing but issues. I have had the repairmen out twice. The first time the washer wasnt rinsing out clothes, when the repairman came out he couldnt find anything. In June of 2017 the same thing happen. Once again the repairman came out. I found out that there was a recall on the part which was on Backordered. Now the matching dryer model MED5500FWD is not drying. This is the worst washer and dryer I have ever own. I will NEVER own another front loader again. Buyer Beware!!!

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

I purchased a Maytag Bravos Quiet Series washer and dryer in 2009. The repair people have been to my house 7 times. The dryer had a useless part on the drum that made a banging noise while running. The washer keeps getting coins and small undergarments stuck in the motor. Every now and then, one of us leaves a coin in the pocket by mistake. I did purchase the extended warranty on the set. The repairperson that comes to my house is great. I would, however, not want to have to keep leaving work to meet repairmen. The machines are not quiet. If you need quiet from your appliances, this is not the set for you. If you do not clean the washer with Affresh or Clorox product, your clothes and your room smells. The clothes are always so tangled after washing; they tend to wear out quickly. Im not sure about this high efficiency washer. I wish I had just purchased a regular machine.

I purchased a Maytag dishwasher in Jan 2012 at Home Depot. It ran fine for 1 and 1/2 years and was only used 2-3 times per week. I returned from vacation and now needs a new control board at a cost of $300. I felt Maytag was a reputable company and am very disappointed. I am a senior and on fixed income and now sorry I chose a Maytag. I will get it fixed this time but that is the last money I will invest in Maytag appliances and repairs. I worry that the washer and dryer will go next as they are also Maytag and are just over 1 yr old.

MODEL # MDB4949SDMO. Purchased Maytag Dishwasher. 07/2014 stop working. I have purchased a Maytag Washer also. It also did not last two years. I am very unhappy consumer. I will not purchase another Maytag appliance. Stop selling these lemon appliances. Need to repair free.

After first dishwasher was recalled, this one (installed less than 4 years ago - Oct. 2010) had the electrical panel burn out - two years ago. Now - for second time. LAST TIME BUYING A MAYTAG!

We bought the Maytag set of dryer and washer just over 5 years ago with ex. war. The dryer now doesnt heat up but the drum does turn. To fix it would cost about $500 maybe more and the parts may only last a few months. I believe that dryer should last longer when only used about once a week. I am now looking at Speed Queen. Cost more but am told they last longer.

I purchased a Maytag stove model mer7765wb in December 2011. Now its November 2014. My display board caught on fire and its burn out. How can a Maytag product go out within 3yrs. I purchased it from Sears outlet. As Sears customer I am very disappointed in this product. Thank God I was in the kitchen to put out the fire.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

I reviewed lots of reviews, and decided that the negative reviews ones were sour grapes or uninformed customers! WRONG! Do not buy this washer. I replaced a 16 year old Frontloader Bosch! Should have had the Bosch repaired, but wanted a topload for a change, new look etc. From day 2 the washer began to squeal during the early cycle and at the end as well. Maytag repair was out for an unrelated repair on another appliance. I told the tech about it and he suggested its brand new etc, give it time to settle in.Now 4 months in and another service call to tell me its nothing!! It squeals so loud I can not run it while in the next room. I have videoed it and sent it to the Maytag repair in Glenwood Springs, and he said I should load it only full enough to see the impeller at all times!!!! Forget a full load of work clothes or a pillow or blanket. Which is to be expected to be able to wash. He said I needed to spread the clothes out manually along the outer sides of the TUB only, prior to washing the clothes! not over the impeller. I am not kidding! This is a open tub, so the impeller is the little thing in the middle on the bottom. I advised him, I videoed the event and even with three socks in it for a test it still squeals like a (well you get the idea). Trying to get Maytag help, but nowhere. Matching dryer door hinge broke first week, it has been repaired. Not good quality at all for the top of line Maytag. Then Maytag Man must be busier these days, than of old.

Omg I am so shocked at all the complaints about these refrigerators.. I too bought refrigerator, stove, microwave, dishwasher from Lowes after a storm just about destroyed our home. I was so excited to have such a beautiful refrigerator and new kitchen...but shortly after it started freezing on the bottom of freezer and leaking all over. My new floors and kitchen cabinet are ruined. Every other day we have to break up ice and clean it out from freezer.. it still then leaks.. several family members have slipped and hurt themselves. Please if anyone knows how to get it fixed without it costing us a fortune let us know. Maytag (Whirlpool) knows it is a defect... Why will they not fix it? I cant afford a new refrigerator and shouldnt have to after only two years.. If a class action comes up.. please contact me. Shame on them...

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

Unless you’re doing laundry for an army don’t buy the Maytag commercial washer MVWP575GW. I should have gone with my original choice but my husband was concerned with the durability and warranty hence why we purchased this washer. It’s just the 2 of us and I frequently use the delicate cycle. Unknown to me at the time you can not adjust your water level so if you’re washing delicates plan on wasting a lot of water unless you only wash your delicates once a month. In my opinion delicates are undergarments, blouses, etc. delicate cycle in “deep water wash” only. As far as we can tell the wash cycle at its longest is 8 minutes which I guess for commercial grade is probably correct. However there is a presoak option that I don’t the believe does the work of a longer wash cycle. If you have to do a quick scrub on a piece of clothing as the washer is filling up you can not do this as everything stops once the lid is up.Last but not least the washer is loud it sounds like it’s going to break down at any minute. I’m sure many of the issues people have with products today are due to government regulations. I’ve tried contacting Maytag customer service on numerous occasions to see if I’ve been doing something wrong even though I’ve read through the operating manual several times, I’m currently on hold for 20 minutes. Doing the laundry has never been the highlight of my day but I never minded it until now. I absolutely dread it now. My suggestion would be if you like the features on your current washer, spend what you need to to get it working properly which is what I wish I had done with my 23 yr old washer. Worst purchase I’ve ever made!

My washer is just past warranty and making horrible sounds! I have always liked Maytag but their quality is bad. I wish I had read reviews before purchasing my washer and want to tell anyone reading this to NOT buy one. My last Frigidaire washer lasted 15 years with minimal repair. Shame on you Maytag!!!

I wish I had read these reviews before purchasing my dishwasher. I have used it 40 times max. The control board went out. They want 307.00 to fix it. Really? Why would I fix this piece of crap when I can buy a cheap one for that price that would work better. Ridiculous! I paid good money for this dishwasher and the warranty that comes with this is a joke. Save your money and brand from a company that stands behind their product.

I purchased my Bravos washer and dryer in about July of 2012. So far I have no complaints about the dryer but I hate the washing machine as do two friends of mine. My husband specifically wanted something energy efficient which is why we didnt purchase the basic traditional style washer weve always used. From the first time I used the washer, I was amazed and disappointed at the noise level. Because the lid is glass, I could observe the water level during each part of the laundry cycle. The water did not cover the laundry in the washer.When I mentioned this to one of my friends, she said that she has to wash some of her clothes twice. How is this energy efficient? I finally figured out that using the heavy duty wash cycle and heavy soil setting usually results in more water but requires an hour to wash and rinse the clothes. The downside is that the heavy duty cycle is too hard on some of my more delicate items so I have to hand wash many more clothes than I did with my old style washer that allowed me to select the water level I wanted. Most recently, when I washed a bulky mattress pad with a few other items, the water level never covered the pad because the load of laundry was so lightweight. At the end of the cycle, parts of the mattress pad were bone dry so I will have to take it to the laundromat if I cannot make the washing machine fill up with water high enough to cover the mattress pad. I dont want to spend the amount of time hand washing so much of my clothing, monitoring the water level in the washing machine and rewashing loads of laundry. After reading many of these comments, it appears that I have many more issues to look forward to. When this washer starts to break down, I will go back to an old style machine and a different brand.

I bought a Maytag washer November Thanksgiving of 2013. This washer started giving problems three months after; problems such as the cycle stop turn over properly, the light would say wash but its not washing. It would just stop but the light stuck on wash for long periods of time. Press the pause/start/cancel button, it would sometimes start again and stop and let out the water quickly. The clothes would be filled with water and not wash properly. This the funny part, serious funny part. I contacted Maytag on countless time. They had me on hold so long I had to hang up; a hold for hour I am talking about. One day I finally got through. They gave me a number to contact because where I am located there is no tech. I never got anyone but the machine when I called the number after countless times of trying. I decided to called back Brandsmart, because I just think its not right and fair to me to purchase a washer for so much, to had it shipped for more money. It didnt last me NO time at all and I cannot get any help. Well! Brandsmart told had to have paid export shipping, something I never was offered and since I took it out of the country, there is nothing they can do for me. I hunted for my receipt and to this day I I still have it. All was offered was warranty parts and labor for a month, thirty days. I said no because I would not think anything would go wrong in that short period of time. Nevertheless was not offered any export shipping warranty like what they are trying to ** me with. Here is my receipt number **. I grieve presently how I was just robbed of my money so openly when all I wanted was a replacement.

Maytag Bravos top load washing machine - This is the worst washing machine I have ever used. Like some of the other complaints it leaves lint on your clothing. It does not put enough water in the machine. The so called smart technology that senses your load does a terrible job. Your clothing is halfway out of the water, with dry spots, even after 10 minutes of agitation. I am constantly adding 3 to 5 gallons of water to my loads to get things in the water. And if I want to let thing soak for a while you have to unplug the machine, because after 10 minutes it will automatically drain the water out. 2 years of dissatisfaction. I cant wait for it to die. I should have come to this site first. Never buy a machine without an agitator!

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

My washer (Performance Series 4000) needed new bearings about 6 months after purchase. By the time the parts came in and after the A&E repairman rescheduled because he didnt know how to replace them, another two months had passed. Now, a year later and with no more warranty, the bearing needs replacing again! This washer is only 1 year 8 months old! The first repair cost well over $1,500 but was covered under warranty. There are hundreds of other people with Maytag washers having the same issues! Maytag is well aware of the defect and refuses to take responsibility. I would like to file a class action lawsuit against Maytag. Im in Tennessee. Please contact me. Thank you.

I bought a Maytag washing machine September 2017. The lid is cracked. We were told by the repairman today that this is a common problem. The quote for a new lid was over $300. Of course we are not going to spend that much for just a lid. We will be buying a new washing machine and will not be buying a Maytag.

It looks big, but is small inside. Its hard to put in several large items. The water filter broke and too expensive to fix. I like the double doors and ice maker. I dont like the freezer drawer. It wont stay open to clean.

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

Last year we replaced a Maytag dishwasher which had a faulty control panel after just a few years of light use (There are just the two of us). It was going to cost almost as much to repair it as to buy a new dishwasher, so we opted for an $800 model (MDB8959AWW6) with a control panel across the top of the door. There had been a recall on that first Maytag for the heating element or something, so we decided to put the credit towards a machine that would last us for years, we hoped!We have been in this house for 18 years and the original cheap builder-installed dishwasher lasted for 12 years. In fact, there was nothing wrong with it when we replaced it with the last one. Whatever happened to the lonely Maytag repair man? We did not buy an extended warranty, but I can see now that probably these things are only meant to last the lifetime of the warranty.We are semi-retired and cannot afford to have the dishwasher repaired, so it will be a decoration in the kitchen from on. Never ever will I recommend Maytag to anyone! One bad experience should have been enough, and we probably would not have bought a Maytag again had it not been for the credit we got for the product recall on the last one!

I, too, have had major problems with this Maytag refrigerator! We have experienced everything from a malfunctioning ice maker, flashing control panel, overloaded compressor, erratic freezer (freezes much of the fridge contents), and doors not staying closed/inadvertently popping open. We have owned this fridge since 2007 and have repaired the ice maker and the freezing problems on our own dime. When the clicking sound woke the entire house up at 5 am, I finally decided to post! I realize that appliances are not perfect, and that Maytag had the best of intentions when designing and producing this product, but what really infuriates me is that Maytag has known about this widespread inherent problem since late 2006! Why no recall? Why no notice? Why no assistance? When I called the customer service line this morning, the representative acted like shed never even heard of this fridge having problems - yeah, right. All you have to do is Google the model number or just Maytag fridge panel flashing and clicking problem to discover thousands of similar complaints. I do not fault Maytag for manufacturing a less than perfect appliance, but I do hold them accountable for adequately repairing/replacing such a rampant and unsafe (compressor overload) product! Maybe it is time for a class action. Something needs to be done to protect the consumer from a company that is so slow to correct a long-standing and potentially dangerous problem!

I bought a brand new Maytag bottom freezer fridge on Aug. 12th, 2012. The main compressor went out on Memorial Day of 2013. I contacted the store I bought it from; they referred me to a local repairman who fixes Maytag. I talked to him and told him the problem along with the make & model of mine. He ended up telling me what exactly the problem was, & there were about 5 people ahead of me with the same fridge, & same problem... all main compressor problems. Check this out. The compressor part is on back order... so now I have no fridge, & Im stuck with this piece of crap, until MAYTAG finds a compressor to ship to the local repairman. - Last Maytag product I will ever own in my lifetime!!!

Bought brand new. No deal, not on sale, not a return. Just heres money... give me working washer. This thing doesnt wash anything. It leaves soap all over the clothes. When you turn it on and wait til it starts washing, look in there with the lid open... theres barely any water! The clothes on top stay dry! The only way to wash your clothes in it is to add three-3 gallon buckets of water at the start of each STAGE of EACH cycle! My wife showed me after three months of washing clothes like this. Anyway, to the garbage with this and back to Whirlpool basics with me.

I bought a model MDB7749AWW1 Maytag dishwasher in May 2011. I thought I was getting a nice one, but no one really liked the way the racks were designed after we got it installed and began using it. My biggest complaint however is with the control panel. It failed in November 2011 and was replaced under warranty. It has now failed a second time in June 2012 (just over one year old and out of warranty). Theyve offered to pay for the parts since it is so close to one year and I pay labor. Well see how that goes. Looks like there are lots of problems with Maytag control panels.

This Maytag Centennial is the WORST piece of junk I ever purchased and I received the same uninterested response from Maytag as everyone else. Maytag sent a service man out who said it was functioning as it was intended. Once started, this washing machine cant stop if you forget to add an item. It dumps out all the water and starts the hour-long cycle over. All settings are an hour-long cycle. Unless Bulky or Delicate is selected you only get 2 inches of water -- Even for Heavy Duty. No matter what the setting, the clothes do not come out clean. You must hand wash them first. Maytags are no longer a desired product.

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

Under a year old @MaytagBrand fridge stopped working and they couldnt get a repairman here for a week. I said this was unacceptable--we would lose hundreds of dollars in groceries and months of breast milk. They didnt care. I asked if they would reimburse me for a private repairman, they said no. Less than a year old. Friends, I implore you, never buy @MaytagBrand. This customer service is truly unacceptable.

I bought this washing machine approximately two and a half years ago. I replaced the agitating wash plate three times. After several months, the wash plate will start free spinning from the gear and will spin like a top. It has to be replaced at $140.00 plus the service call. When it was working, it doesnt clean the clothes well. I contacted Maytag numerous times about this problem and they basically gave me a tough luck answer. I just went purchased a old style machine with a tall agitator that will clean like its suppose to. Its a shame Maytag has no compassion to try and compensate customers for the expenses. I also contacted Whirlpool which took over Maytag. My rating is a negative five.

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

The Maytag Commercial Technology wash machine, the one with the clear top, leaves soap residue on our clothes. We have tried different detergents, always high efficiency, using the extra rinse, using the deep fill and nothing works. We have tried cleaning with vinegar and using the clean washer cycle. We had 2 technicians look at it, one tore the machine apart, both said nothing is wrong with the machine. So, we are left to believe that we are stuck with a machine the leaves soap residue on our clothes as Maytag will do nothing for us because of the assessments of the technicians.