This washer is the worst! Dont buy it! I paid a huge amount of money only to have it break down in 3 years! My husband and I live without children so our use is minimal. The spin cycle started to make a noise sounding like an airplane taking off. The repairman said it could be fixed for $800 and his service call, he told me that there were over 2400 complaints with this washer for the same product. He also told me not to use it while Im out to avoid the risk of flooding my home! Save your money and DONT BUY MAYTAG products.

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

Purchased this washer in March of 2016 for a family of 2. In July of 2018 had to have system board replaced. Now here we are beginning of 2020 and washer is making grinding noise and did not spin out properly. Will not buy another Maytag, a washer should last more than 4 years. Poor quality product. Do not waste your money!

13 months after purchasing MDB7749SBM3 dishwasher this lights started making no sense. For me the buttons still work, but it seems like only a matter of time until they stop working too. Like many others, I opened up the door and found the corroded ribbon connector (see photo). It wasnt damp so since the corrosion happened at the point where a ridge of plastic presses the ribbon against the hot handle, I suspect heat. Obviously a design flaw. Come on Maytag. Recall?

I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

I purchased a floor model Maytag Dishwasher from Abt electronics about a year and a half ago. 2 months ago, various light started flashing. Somehow I managed to get it going. Some blogs reported it might be a drainage problem. Others suggested pressing a certain sequence of buttons. After Each time I got it to work, it became harder the next. I bought Maytag because my old dishwasher lasted 13 years. What is interesting is that a company whose name Ive forgotten sent me bimonthly requests to purchase a warranty from them. Now they have stopped. I am a single mom of 3 with an unemployed ex. I work and support my family without any assistance. I count every penny. I cannot afford repairs nor a replacement now or any time soon. This is a travesty.My door says 10-year limited warranty and the delineates stainless steel tub and racks and chopper blade, but not the panel. I do not understand how Maytags denial of the problem and their unwillingness to correct the problem can improve their image. I will never purchase from Maytag or its associated companies ever again. What a scam! To be honest though, I have not contacted the company since it is not under warranty and all the blogs have relayed the same message: Maytag denies there is a problem.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

I have to agree with all these other reviews. This washer twists clothes and does not wash them at all. If you open the lid mid cycle you will see dry clothes on top... Isnt that the whole purpose of a washer? WTF. Steer clear of Maytag. They realize that theyre selling washes to Generation Xers and they can get away with it because we were the first throwaway generation. Great business plan Maytag!

My washer is just past warranty and making horrible sounds! I have always liked Maytag but their quality is bad. I wish I had read reviews before purchasing my washer and want to tell anyone reading this to NOT buy one. My last Frigidaire washer lasted 15 years with minimal repair. Shame on you Maytag!!!

I have a MFX2570AEM French door refrigerator. Like many others on this site I have ice building up under the freezer drawer. Water also leaks onto the floor. We keep a towel there constantly. We bought this refrigerator along with a dishwasher and microwave, all Maytag and have been disappointed with all of them. We thought Maytag made quality appliances, but my experience tells a different story. I havent called for service yet, but will later today.

Bought this Maytag microwave mmv 4205ds March 2016. Have had open/close problems five times in 3 years. Unit replaced under warranty once. Now out of warranty. No need to mention inconveniences we’ve been through. Whirlpool-Maytag obviously have done nothing to correct this problem. I will never buy any of their product again. Wanted to give them ‘0’ stars but program won’t allow me.

Works quietly and efficiently and I love it! I dont even know its running and the dishes are sparkling clean when they come out. How could ask for anything more. I would always purchase this brand again. The reliability is another factor, I have had Maytag before.

So far we have replaced the belt. Clothes have never come out clean. High Efficiency... Yeah, we have to put it on extra rinse to rinse all the soap out or wash twice because the clothes just do not get clean. Now it stops right before it drains after the wash. So I had to pull out clothes and use pitchers to get water out before we could tip forward and pull hoses to drain the rest. We checked hoses and connections. All lights work, it did a wash cycle, and again stopped before the drain. Really. All I got was “Didnt you take out the extended warranty?” Well, No I did not. Why would I consider the fact that MAYTAG would need repairs within the first 3 years. Its not like I do a lot of wash. Or have big bulky items. I have a laundry mat close by for that stuff, because it wouldnt get it clean anyway. Never again…

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

We purchased a MDB8949SAW dishwasher in 2013. 1 month after the warranty expired the touch buttons went on it. If you selected normal it would opt for something else like rinse only. We researched online and my husband followed instruction online to take the door off and seal the moisture to prevent this from happening. This worked for about 2 months and now back to the same thing. We paid $500 for this and just living with the problem for now. All we can do is warn others.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

I purchased my Maytag Refrigerator in Feb 2013. It is model MFF2558VEW7. It has the French doors w/ freezer at the bottom. This past week, I lost everything in the freezer. I call the Home Depot where I purchased it and they said that I have to call Maytag. I did and they sent a repairman out. It needed a compressor. After only 8 months, the compressor goes out? Why should this fridge be repaired and I not be given a new one? With all the problems with the Maytag, there needs to be one big class action filed. I asked for a loaner because it would take up to five work days for them to order the part. The answer was, We do not provide loaners.

We bought a Maytag refrigerator less than two years ago because... its Maytag. Less than a year later we had five service calls. The refrigerator wasnt cold, the freezer was the temperature of the refrigerator and it took two months and two different repair companies to fix it. And now... yes, the same problem seems to be occurring. It was a leak that was supposed fix. Cant bear the idea of going through this all over again. NEVER again Maytag!!!

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

Purchased a new Maytag dishwasher just under 1 year ago. After a 5 months it started not working. We called the dealer - who gave us a number to call because it was under warranty. We called the number and it took days to get someone to look at it and not fix it. It needed a new part. Its been over a week now and we havent heard anything, and still no working dishwasher. Our last two dishwashers lasted over 18 years. Kenmore and Whirlpool, never had any issues. This is our first Maytag. Service has been snail pace slow. Dont buy a Maytag dishwasher unless you want to spend your life washing dishes.

If you are looking for the Maytag repairman he will be at my house Tues fixing my barely 1 yrs old dishwasher. This is ridiculous to pay this amount of money for the reputation that Maytag is known for or I will say was known for. $270.00 for a control panel. My last Maytag lasted over 30 yrs. Not made in the US - not built to last and this was told to me by the people that installed it so take it for what its worth. Look elsewhere. My last Maytag product.

We recently purchased a Maytag refrigerator, love it, no problems until the mystery person in my house accidentally broke the slide out door for bottom drawer. So I called Maytag, and with no questions asked they sent me a new part by Purolator! Great customer service makes everything better! Thanks Maytag.

My husband bought a washing machine in August 2019 and now it broke down a month ago. There is a sticker on it that the warranty is 10 years, but this warranty is for the motor and not for everything else. I read on the Internet what kind of error the machine gives me, it turned out to be either the motherboard or the front panel. I did not order the parts myself, called the service, in 5 minutes I had to pay 130 $ to he told me the same thing that I read in Google.... And he said that the repair would cost another 500$ part - 250$ and service fees to replace the front panel or the motherboard. Its ridiculous prices, so I find parts lil cheaper and ordered the motherboard myself, my husband installed it (there is nothing hard to do it) and the machine still gave the same error, I ordered the front panel for 220$ and the machine still gives the same error. Now front panel didnt respond at all, and this brand new panel... So I bet after I will pay to service they will tells me there is something else broken... Maytag??? NEVER AGAIN!So I send all part to the store, save money this way and now I buying a new one, when a year and a half ago I spent 1000$ on Maytag and the service is trying to rob me at the cost of a new machine, and no one gives me a guarantee after the service, I will not have a new one. The way out is possible to read more reviews and take a protective plan for 5 or more years so this is not your problem.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

The dishwasher stopped working. The lights on left side of control panel arent working; so, machine wont start. Then machine was purchased in January 2010 for $525 and not including installation. Kim says it will cost $129 for their repairman to come look at it. I wished I had read the list of complaints on your site first.

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

New side by side, water inlet to ice always freezes. Had a service man out, said some tube needed to be enlarged but still freezes up.The ice dispenser is total junk. Keeps spitting out ice after glass is removed and just a poor design. Dont recommend this brand.

I received my Maytag dishwasher in November of 2013 from Home Depot (It was a month overdue the expected delivery date). It was installed by a certified electrician/contractor. By February of 2014, the control panel had to have its first replacement. It is now July 2014 and we are having the repairman come out to replace the third control panel this Monday. Supposedly there was a recall on the control panel and the one replaced less than a month ago was the improved/repaired one. We are beyond frustrated. I too sought Home Depot for help after the first repairman they suggested charged us almost half the cost of the dishwasher for his repair. I have already sunk over the price of the product into repairs. My Maytag dryer broke last week as well. Someone needs to get involved with this situation, perhaps a contact to the media? I think we are all being scammed and deserve refunds by Maytag for the dishwashers and our repair costs.

I bought my Maytag dishwasher in February 2011. It seemed like a good model - basic functions, upper spray arm, stainless interior. Well this dishwasher has been all downhill since I got it. First it is cheaply made. The racks and plastic stoppers on the racks immediately started falling apart. The one year after we installed it the front control panel went out, rendering the dishwasher completely useless! The warranty had just run out! To my pleasant surprise, I received an extended warranty offer from Sears. Had the front panel replaced and it started working again.... but apparently it is a bad design and it is likely to happen again. After reading online I am not the only one with this problem.Now another year later we are having a the sprayer on the top and the back hose replaced..... (still waiting for sears to install). It makes grinding sounds, leaves white marks, doesnt clean.... it is a non-stop battle with this product. Upon calling Maytag, they said they could give me advice but cant pay for any parts or even give me a coupon towards a new product! I have tried everything with this dishwasher - fancy soap, cleaning solutions, jet dry... its not me, its Maytag! I will likely be in the market to buy another dishwasher next year because of all the issues, and it for sure will not be a Maytag.

Maytag Centennial HE Washer - Worse machine ever. Takes over an hour for a load of clothes, never clean. Had only for 18 months now, it wont advance past wash cycle.

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

In 2016 I purchased a matching Maytag washer and dryer. The reason why I purchased it because I was in a house and I no longer had a washer and dryer and I refuse to go to a laundry mat at the city to go to Nebraska Furniture Mart and it was a number of different washer and dryer combinations available. I had previously own a Samsung matching washer and dryer and it worked fine, my Maytag has dame of the same features and works great.

I purchased a Top Loading Maytag January 2019 (High Efficiency Washer) and I have had problems with it every time I do laundry. It doesnt matter what cycle I have it on. It doesnt fill properly when I put it on deep full. It tangles my clothes so I have to untwist them when I take them out. It has torn some of my things due to twisting. Some areas of the clothes dont even get wet. Some areas also do not get rinsed properly and I have to repeat the cycle. I have had repair people come out and they cant find anything wrong. I am so unhappy with the washing machine and Maytag just ignores the issues I am having. Im going to have to give it away and get some other brand. I am just devastated that I spent all of this money and clothes are getting ruined.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

I bought a Maytag Gas Range in January 2010. In January 2012, the wiring caught fire, and now, the oven is unusable. Maytag was not very helpful in our loss of money and product.

I bought it from a local dealer so that I could get it serviced locally. I bought it in 2012 and paid $750 for it. I hate just about everything about this (and all modern) washing machines. The deal breaker is all these safety features that are really inconvenient and pointless. If I could have found a good used washing machine at least 10 years old, I would have bought it. This is a Maytag Centennial. I dont like the automatically locking door, the inability to choose the water level myself, and the requirement to use a particular kind of soap. Also, I hate the idea that I have to clean the washing machine from time to time. Whoever heard of that? But you have to do it otherwise your clothes will have a sour smell. These new washing machines are not an advance in technology. I may have to go back to using a wringer machine.

MDB8959SBB. Purchased this Maytag dishwasher late December 2013 and had it professionally installed on January 4, 2014. Could have burned down the house this weekend! Smoke everywhere! Thank goodness it was running during the day and not night so that we were able to shut off the power. Lights in the kitchen were blinking and smoke pouring out of the dishwasher. The house still smells of smoke. So disappointing. Ive always been a proud owner of the Maytag products. Never again. Especially after reading the reviews. Interesting enough, THIS dishwasher was purchased because of a recall on the PREVIOUS Maytag dishwasher I had trouble with. They gave me a credit to use towards my next purchase. Ive learned my lesson.

After first dishwasher was recalled, this one (installed less than 4 years ago - Oct. 2010) had the electrical panel burn out - two years ago. Now - for second time. LAST TIME BUYING A MAYTAG!

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

I purchased Maytag Quiet Series 300 Dishwasher in 2006. About 3 years ago, I got a letter that a recall had been issued due to an electrical problem. A service repair person came out and replaced the electrical element in question. Next the dishwasher did not work and a repair had to return again. Today I have the same electrical problem and after waiting on line 12 minutes to talk to Maytags customer service, I was told it could cost me a couple of hundred dollars to repair my 7-year old dishwasher. In my last home, my Kitchenaid dishwasher lasted 20 years before needing to be replaced. My daughters Maytag dishwasher lasted on 12 years. What ever happened to Maytags lonely repairman? I now have to get a new dishwasher and worry about my $3000.00 kitchen floor getting damaged with the removal of old and install of new. Believe me, my new one will not be Maytag.

This is undoubtedly the worst washer I have ever owned or used! I have never before felt compelled to write a review on a product, but I wanted to make other buyers aware. There is not enough water to clean the clothes - the water level doesnt even cover the top of the clothes, so the top of the clothes are dry as they are agitating! After drying (dryer doesnt dry either) the clothes do not smell fresh or clean. Ive put up with it for 3 years and am disgusted every time I use it. Im just about ready to buy another set.

I purchased a Maytag Electric Range (Model: MER7662WS1) at Lowes in February 2011. After few months, we found many rusty areas on the stainless oven door and on the stainless drawer.On 9/8, I called Maytag at 1-800-688-9900 to complain that stainless steel is not supposed to rust. A representative took the initiative to schedule A&E Factory Service to come to my house for a warranty repair, and assigned me an order # 40629499. I did not request for this service call and naturally, I regard this as a warranty service or a service of quality check of a product.On 9/19, a technician came to check the rusty area and confirmed that the stainless steel have rusted and the rust will eat through the panel. The technician called Maytag, and got the answer that Maytag will not pay for his visit because its not under warranty. The technician then checked the warranty manual, but could find not any statement that neither rust is cosmetic nor rust is not covered. The technician asked me to pay $132 for his five-minute checking service. I was so upset and called Denice at A&E Factory Service at 1-800-905-9505 to bill Maytag directly. She ignored my request and said that I should take it to Maytag.After a couple of hours waiting, holding and transferring, I explained to two Maytag customer service representatives my problem, only to get a Sorry, its not covered, its cosmetic, reply. I insisted talking to a manager and finally got Melinda at Care Solution Team. She, too, refused to waive the charge for me and claimed herself as a supervisor and decision maker and theres no one above her who could resolve this issue.I emphasized that A&E service call was authorized by Maytag, I did not order the service. Who would have thought that a service authorized by manufacturer is not covered under warranty? Besides, this representative failed to inform me that rust would not be covered, she should have known better. Therefore, I believe that the person who initiated the service call to A&E should be held accountable. But Melinda never wanted to agree with this logic and kept saying, We dont force customer to have home service. You are liable for the bill.She refused to pay for the service and forced me to pay the bill from the mistake they made. She even refused to give out the persons ID # and name of the person who called A&E. She only documented my complaint--whats the point of their documentation? If this is the tactic that Maytag is using to categorize rust as cosmetic (if rust can damage material, then you should not call it cosmetic), and ban customers from claiming the rust damage so they can use poor quality of stainless steel on their appliances to save the cost, then, it is dishonest to advertise that this oven is stainless.A representative even said that Maytag should have emailed me with the confirmation of service call and noted that its a non-warranty service. Also, A&E should have informed me before arrival that the service is not covered. All these were not true. First, I did not receive such email from Maytag or Whirlpool. If Maytag would have warned me with non-covered policy such as this, they should have the courtesy to call me in case the email was unreliably routed to spam box. A&E only informed me that they are coming the next day, but no such thing as telling me that the service will not be covered. Even their technician did not know about the non-covered issue, and had to call Maytag today to find out.Had the person who scheduled the service told me that the rust on the stainless panels is not covered under warranty, will I still allow the service call and agree to pay $132 for a five-minute checkup and watch the technician leave without performing any repair? I asked Melinda to let me talk to her supervisor but she said that theres no one who can talk to me, and the only way to appeal is to write to the companys executives. The address is: Whirlpool Corporate Office553 Benson Rd Benton Harbor, Michigan 49022. I doubt that an appeal will help me at all. I will take this matter to small claim court, I wont let them force me to pay the bill when I am not at fault.

The refrigerator is barely over two years old and the bottom pan fills with water, freezes and leaks out onto floor. Is a very common problem with these refrigerators and Maytag is happy to pay for the new part to fix it, but will not pay for any person to fix it. They have known this is a problem for a while, but will do nothing to fix it. They clearly do not stand behind their product with a known ongoing problem. The Maytag repairman is no longer not busy. Will never buy a Maytag appliance again! Will take the new part and fix it ourselves.

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

Received new washer & dryer on Oct 2nd, 2015. The dryer has been acceptable, but the washer has been one problem after another. First of all the washer is so noisy beyond belief. The engineering is one dreadful design. At first attempted use, washer would not begin cycle. Sensor would say lock, unlock, lock, unlock for so long, I would cancel & begin again. It became such an annoyance that I placed start of cycle on a timer (it sat at sensor mode for 20 min.) then I restarted next time sat for 15 minutes without starting. After beginning from start position it would start OR NOT. First repairmen told me timer might be off a bit. As days passed with same issue, second repairmen arrived and found that door was off (not completely closing). Repairmen would place an order for new seal. Upon repairmen arriving for third time (new seal did not solve issue) he believes that lid is uneven, & he will order a new lid & return in a few days to repair. I must admit that service has been quick, but the issue is still a headache. I would NEVER recommend this model to anyone and would like for Maytag to replace washer with a different model. The noise is a factor that no one should have to endure. The grinding noise can be heard from three rooms away from laundry area with laundry room door closed! Im absolutely a very very unhappy customer.

Maytag Neptune MAH8700AWW and MDE9700AYH Washer and Dryer - Electrical overload to house circuit, multiple water pump replacements (Maytag would not sell rebuild kit with impeller and gasket or seal causing us to have to buy complete water pumps with mounts and motor.), electronic error readouts, odor and mold washing machine. The welds breaking on the drum causing possible fire hazard by filling case up with dryer lint fibers, around the electrical components, and air intake heater and also allowing metal fragments to get imbedded in the familys clothes. Also, Maytag Oversize Capacity Plus Quiet Pack Heavy Duty with Lifetime Tub.

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

The water drainage tube on the Maytag Refrigerators is DEFECTIVE and needs to be replaced during manufacturing of the appliances!!!!!!! The existing drainage tube kit in the appliance has a very tiny opening for the water to drain and what was not factored in during this manufacturing of the refrigerators was bacteria and dirt build up from the water draining to CLOG this very TINY opening in the existing drainage tube system. This results in the water having no place to drain except causing an ice build up in the freezer and then water draining onto the floor when it has no where to drain in the appliance. I am told by my reputable Maytag repairman, who also needed the same repair, that replacing the water tube drain #W10619951 occurs with customers 4-8 times PER WEEK in his practice. This is obviously an ONGOING defect that Whirlpool is IGNORING and needs to be addressed and corrected with some type of compensation for its customers. The service call and the replacement of the drain tube kit #W10619951 cost me $122.31. My Maytag refrigerator with a bottom freezer is less than 3 years old.Amazing also if you google MAYTAG refrigerator leaking water there is a MULTITUDE of youtube videos and websites instructing the consumer on HOW to replace this part in the refrigerator. Obviously there is a strong need for this instructional information to the consumer for this repair since it is an ONGOING PROBLEM that has not been addressed legally with manufacturer. Action needs to be taken. I am saving the original part that was removed from the appliance in case a class action remedy is necessary to correct this costly defect in the Maytag Refrigerators.

Wish I had reviewed Consumer Affairs reports. When our old Maytag stove required repairs we decided to upgrade old stove instead of putting money into old unit. Looks like a huge mistake. Not only was there a delay in receiving unit after placing order but oven will not preheat. Two weeks before Thanksgiving we were promised a working unit. Now we are only 2 days from Thanksgiving, 2 repair companies have been at home to repair. Requires new circuit board and a new regulator to repair and no promise we can obtain parts. Now I have to figure out how to feed my family for holiday. I am pretty well done and after reading other reports that they are better in junkyard I think I will try to make them take back this defective Model 8800 product. Sitting in our kitchen unusable for the holidays. Dont buy Maytag as customer service does not exist.

I purchased a new Maytag top freezer refrigerator. From the time it was delivered the freezer temp never went below 10 degrees. It ran between 10 and 20 degrees. Ice cream was soupy, bread did not freeze. I called Good Deals Appliance in Fort Myers, FL where I bought the refrigerator 3 days after delivery to report the freezer problem. They sent a service tech out who looked at it and said the model I bought has no freezer control so it could not be fixed. The store I bought it from said Whirlpool, who owns Maytag, said 10 degrees is acceptable for the model I bought so there was nothing the store or Whirlpool would do to replace it. I called Whirlpool numerous times, was on hold for over half an hour each time and was told 10 degree freezer temp is acceptable. After considerable arguing, they agreed to send a second repair person who came out and said the freezer temperature problem could not be fixed. After numerous additional calls, a complaint to the BBB and a stop payment on my Visa, Whirlpool sent a third service person who said it could not be repaired. I began the round of phone calls to Whirlpool again as well as to the Good Deals salesman who has been as useless as possible, continually saying it is our problem to deal with Whirlpool. The BBB contacted me and then Good Deals who said Whirlpool has agreed to replace the refrigerator but I have to contact Whirlpool. I have called Whirlpool, waited forever on hold, and left three messages and no one has returned my call. Whirlpool should not call what they do customer service. They are rude and argumentative and make it very difficult for customers to contact them and even more difficult to get a defective appliance replaced. DONT EVEN CONSIDER BUYING WHIRLPOOL OR MAYTAG APPLIANCES?

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

This is the loudest washing machine Ive ever had!!! I ask the installer if it was suppose to be so loud & he said yes. The machines sounds like metal scraping metal when its washing the clothes.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

I am extremely unhappy. This is a terrible washer (Maytag washer MVWC565FW). I am so sorry I didnt buy a GE. Terrible loud noises, shakes and vibrates like a plane taking off. Funny smells as if something is burning. Repairman came 1 week after purchased and stated nothing was wrong. A huge waste of money, I HATE, HATE this horrible machine!!! Totally unsatisfied, I would never purchase anything with the Maytag name again!! Wish I could get my money back!

I emailed Maytag https://www.maytag.com/contact-us/ about my model number MBL2258XES3 Fridge on Dec 31. They scheduled a local appliance repair company and they came out today, Jan 5 and did the repair and defrosted the compressor and freezer compartment. 45 Mins is all it took. Thanks Maytag.

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

I bought a Bravo XL Washer 3 yrs ago for $900 to $1000. The washer started beeping and not starting to eventually not turning on. I called customer service as I was told my washer was still under warranty. They scheduled a service man to come out with a $95 charge to come out. He came and it is the user interface. Apparently, this is a huge issue with this type of washer. He told me it would be cheaper to get a new washer than to have this one fixed. I called Whirlpool/Maytag after the fact and was told the part is $422.49 to fix the washer. I explained that I was told it was still under warranty and they denied this is the case. My previous washer I had for 18 years and not problems until the end. Having a washer for 3 years and being told to purchase another one because it would be too expensive to fix the current one is very disheartening! I do not recommend this product to anyone, nor do I recommend the company as they do not try to make things right or offer any assistance in any way! Buyer Beware.

We have had our washer and dryer almost 18 years and just recently spent less than $280 to get the washer going again. The dryer we haven’t had serviced yet. Great quality. So worth it. Our Maytag appliances are used frequently and keep giving out the best performance.

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

Purchase brand new range a couple of months ago. Self-clean oven does NOT self-clean and leaves weird, flakes of something that stick to oven floor. Burners are inconsistent and difficult to control heat level. Take forever to get warm, and then either boil over or wont get warm enough. Purchased this with inheritance from my mother - how sad! Always had such faith in Maytag.

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

We bought ALL new Maytag appliances for our home when we rebuilt after it was destroyed by Hurricane Katrina in 2005. We got the top of the line of every appliance. Our Maytag dryer model MDE2706AYW has broke for the 2nd time and cost to repair this time forces me to replace it. The dryer felts, idler pulley and belt went out several weeks ago. Used it about a week and the drum quit turning. The repair tech said the aluminum pulley for the belt on the motor is broke. The pulley is not serviced/available and you have to buy a new motor assembly. This puts repair price on up there where replacing the dryer is the only option. We are going shopping for a new dryer today. It wont be a Maytag.2 years ago, our Maytag washer broke. The repair tech said the transmission went out and it would cost less to replace the washer than to try and repair the Maytag washer. We bought a new washer, different brand. About 3 years ago, we had to have our Maytag dishwasher control panel replaced and 2 months later the pump housing broke. Repair tech said cost more to repair than new. Replaced with different brand.Shortly out of warranty, our Maytag Microwave broke. Everything worked except it would not heat anything. The repair tech said cost more to fix than new. Replaced with different brand. All we have left is the refrigerator which has had 2 expensive repairs done on it and the stove which has had the control board and several heating elements changed. I will never buy another Maytag product.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

We purchased a Maytag Bravos set in 2011. The dryer works great, but the washer not so much. Every load of darks comes out with soap scum all over. I use the HE detergent and most time use less than what the load should have. We have soft water and I also use softener. Ive also tried up to 3 extra rinse cycles and a smaller load size and still have soap scum all over. Im sure the light colored loads come out same, just cant see it. Needless to say, very, very upset with this washer. I, too, will never buy another Maytag product, nor will I recommend one. Had our yearly maintenance check the other day and the service man couldnt give me the reason its doing this. So, so disappointed in this product!!

We purchased the Maytag Atlantis used (4 years old); it looked like new. When I opened the lid, I noticed a terrible smell like some left the clothes in the washer for days. I used white vinegar, baking soda, bleach, anything to try and get rid of the smell. Nothing worked. Finally, my husband took out the agitator and then the drum. Inside and around the drum was lint from all the years of washing clothes. He scraped it all off and bleached it and put it back together and it was okay for a while. It now smells again and I am afraid we will have to keep doing this or our clothes will always smell. I also leave the lid open after a wash so Im not attacked by the smell when we open it. I also had the Maytag Neptune front loader years ago, and the water pooled by the gasket on the door. That smelled too! We will be redoing our laundry area soon and will be shopping for a new washer and dryer. It will not be a Maytag!

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

I have owned several dishwashers thru the years and my favorite is Maytag. Maytag is quiet, barely hear it running which is rare for a dishwasher, dependable and plenty of space for dishes, pot and pans etc. I wouldnt have any other but Maytag. Also has several options for dishwashing which is a big plus. Love Maytag!!!

Maytag Centennial Washer - If a wash load becomes off balanced, the machine stops. No signal or buzzer or anything to alert me to this. It happens all the time and wastes a lot of my time. Here I am thinking that the wash is going fine only to find out 2 hours later that it has stopped. Anytime I wash more than 3 items, this happens. I will never buy one again and I am telling everyone not to buy. I will be purchasing a good old fashion washer with a dial gauge so I can spin it any time I needed.

I bought a Maytag front load washing machine. We paid $1,100 for this machine. About a month ago, it was making a loud noise. I called them and they said were going to come out and fix it. However, our washing machine did not have a serial number. It had the model number/purchase date, etc, but no serial number. Our drier had it, but not our washing machine. All Appliances stated they could not help us until we had a serial number. We spent around 3 hours on the phone with Maytag, trying to get a serial number. Melinda informed us that we were out of luck, and that there was nothing they could do for us. She stated to call Nebraska Furniture Mart, to get the serial number. We did. NFM does not keep serial numbers. They keep model numbers, and purchase dates, but not the serial number. I called Maytag back, and spoke with Arthur. Within 10 minutes, he gave me a serial number to use. Interesting. In the meantime, I have been without a washing machine for 2 days. I have a load of wash in the machine, because now the wash machine has gotten so bad it is shorting the breaker, and not allowing electricity to the machine. This caused the front door to lock and shut down. Inside the washing machine is a load of clothes. All Appliances now has the serial number to order the parts. The parts were supposed to be here yesterday, Jan. 9th. Surprise, they are on back order until Jan. 13th. I called Maytag to see what they could do regarding me without a washing machine for over 5 days, which could turn into 2 weeks. They simply replied that it takes time to order parts, and there is nothing they can do and apologized. I asked what about me having to go to a laundromat and sit for hours, doing laundry. What about sending me out a loaner, to do laundry until you can get the parts. They again replied; there is nothing they can do.I also stated I spent $1,100 for this front load top of the line, Maytag washing machine, because of its name, and supposedly good quality. They again said there was nothing they could do. They did tell me that the washing tub, the part that we needed, was on back order until January 28th. This puts me at about a month without a washing machine. They stated they would try and locate the part, and have it sent out to my house, not the appliance company that is supposed to fix it, but my house, so that once I did receive it, I could call All Appliances, and set up the time/fixing of the machine. This has been pure hell! Maytag is a joke. I paid a good price for a supposedly good company/machine. They are doing nothing to expedite the parts. They are doing nothing to back their products. They are not even offering compensation for my inconvenience of having to go to a laundromat, or being without a washing machine for over a week, and potentially up to a month.I have been without a washing machine for over a week. I have had a load of laundry locked in the washing machine. I have had to drive to a laundromat to do laundry, which includes time and mileage. I have been informed that the parts are on back order, and now could be up to a month without a washing machine. Maytag is not offering any compensation, no loaner machine, no replacement. Instead, they are just saying, sorry, you have to wait for the parts. I would really like the VPs. and Presidents of Maytag to go without a washing machine for a week, or their families to go without a washing machine for a week, possibly a month, and see what they have to say about that company.

We love our Maytag ovens. It always cooks evenly and we never have HAD any issues over the past 2 years. We will always buy Maytag! It has a self cleaning option and I have never burned anything on the oven.

I have a Maytag Neptune washing machine which had a mold problem on the rubber grommet. I have been trying to call Maytag to no avail. I researched and saw there was a class action suit for this very problem and I was never informed. The washer may pose a health hazard and I would like Maytag to do something about it.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

I share the complaints of others about the Maytag Bravos washer (model MVWB300WQO), which I purchased in October of 2009.Besides being overpriced, its a washer that doesnt soak clothes, develops a bad odor, has silly things like unnecessary lights and music, and you cant add an item once the wash cycle has begun without the cycle starting over from the beginning. It also leaves washed items in twisted wads and the lid locks so you cant see whats going on inside. In addition, it damages items. Ill have to replace a full-sized blanket that it recently destroyed and now I cant trust that itll wash things safely, which is a problem. The person I spoke with at the companys customer service department simply said that I shouldve used the bulky item option instead of the regular cycle. I explained that Id used the bulky item cycle before and the same thing happened. The washer leaves larger items stretched very tightly across the tub and I suspect that is how my lightweight cotton blanket was destroyed. She offered to schedule someone to service the washer. But its not broken, its a poor design, so sending someone here would be a waste of time.

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

This is the best microwave that we have ever purchased. I especially like the baked potato choice. Its also very easy to use and clean. I would definitely recommend it.

We just purchased a house with new appliances. They are Maytag. When I use my stove the oven heats. I have no idea why. I wondered if anyone else has had this problem. When I turn it off it turned off but it turns back on when the oven is on.

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

April 26, 2011, I purchased a Maytag top and bottom fridge from Home Depot. After a few days, I noticed frost starting to form in my frost-free freezer and the fridge wasnt really that cold. I adjusted the dials thinking that may do the trick. Nothing changed, it was all the same and instead, frost was thicker. I contacted Maytag, which by the way was taken over by Whirlpool. I told them my situation and since I had just bought the fridge, I wanted a new replacement. They told me things didnt work that way, that I had to honor the warranty. Fine, we are almost entering October now. I have had several services calls, I have written to the Better Business Bureau, I have lost a few hundred dollars worth of food for it would be full of ice and had to be thrown out, I have contacted the executive offices of Whirlpool but they, along with the Better Business Bureau are not doing a thing. Tomorrow, once again, I am having a service call and once again, I know the issue will not be fixed. All I wanted was to either get my money back, along with extra for the loss of food or for them to just exchange it for another one, since this one was purchased with a problem. I really dont think that its right that they are able to get away with this. Just looking at this page, I see that there are plenty of people with this same issue. What is being done about it? If it were them with this issue instead of us, you know ** well they would have had a new fridge the following day. Here is my model# M1TXEMMWQ and serial# VS04658359 for this fridge. Please, I would really appreciate some help here.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.