I have been using washing machines for 50 years. This is by far the worse piece of engineering I have ever used! On deep water wash, I would expect my clothes to be covered by water. I actually have to add by hand, four buckets of water and even then the clothes just float on top. The agitator NEVER pulls the clothes down to the bottom of the tub, they just move back and forth. The clothing that sits on top of the water, never gets totally submerged and is still on the top of the pile when the wash cycle is done. I will NEVER buy any MAYTAG product again. Lowes wont help me. I want to sell it, but in all good conscience, I cannot unload this on another person. I cant even feel good about donating it as it does not work...It is Junk!!!! Shame on Maytag for selling a scam. If there was any integrity in this company, someone would contact me and give me a better model.

I love the way it can really handle large loads. The dryer is the best though. It actually dries your load without you having to turn it on more. There are many different choices that handle drying. So, no more to the bone drying.

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

Washer goes off-balance even when clothes are evenly distributed in tub. When it is turned off to rearrange clothes (which may have to be performed a couple of times), washer goes back to starting cycle which means more water. Afraid to do laundry unattended.

Purchased a Maytag Bravos top load washer and dryer in May of 2011. We had our other Maytag washer and dryer for 14 years, and they were working fine when we sold them. We saved a year for a new one. We spent $1,700.00 for them both. We assumed they would last as long as our old ones. Been buying Maytag our whole lives. Besides the clothes not getting cleaned. Besides the washer smelling, even after we clean it regularly with the product proposed. Besides it not working on the normal function. Besides it shredding our clothes if you put it on the highest spin speed. It started to make a very loud noise. Like an airplane taking off. Called a friend of ours that use to have an appliance store in Fenton, Michigan for decades. He said it was the bearings and that You have to replace the whole tub. A $300-$400 fix. And that it would do the same thing again in a short period of time. He said that they are junk.We would be better off buying a new one. He said, The ONLY one you can buy now that will last like they use to is Speed Queen. I had never heard of them. They start at about $750. But they are worth it. He said that they dont make any washers to last more than 3-4 years anymore. We will NEVER buy Maytag again. And Sears wouldnt give us the time of day. Each time we called and asked to be switched over to the recall department, we just got a busy signal, then a fax machine noise. We have shopped at Sears for years. Boy, loyalty doesnt mean anything in this day and age. Im sure Speed Queen will be happy to help us out. DO NOT buy any Maytag products. There should be a class action suit against them for this. There are thousands of us that got ripped off. I cant tell you how upset my husband and I are about this. We are retired, and on a fixed income, and I am disabled. The stress this has caused cannot be put into words.

We bought our beautiful Maytag refrigerator model MFI2568AES at our local Home Depot approx. 4 to 5 years ago. The refrigerator stopped cooling last week and we had just renewed the warranty for 3 years. The service repair stated that the problem was not covered (internal corrosion) and they could not do anything for us. Is this how long Maytag refrigerators last? Home Depot was also not willing to do anything for us. Were very upset and disappointed and using ice chests for now.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

I bought the washer dryer combo. Dryer already broken. Washer is very loud when it changes gears. Would not recommend the washer or dryer.

I bought a Maytag dishwasher in Sept. 2013. This dishwasher looks great, but it leaves glasses stained with a cloudy haze. It also does NOT dry, even on jet steam dry mode. Bottom line, after a little research, I was the one who bought it, so I took accountability and just rolled with it. Well, the control panel stopped working this week (wont light up). I called maytag and the lady told me they would cover a service call and parts even though its not under warranty. When the service company called me, they said maytag will NOT cover cost, totally contradicting what the Maytag lady told me. After reading these other posts, I wish I would have visited this site before I bought this headache of a machine. I will never buy Maytag again!

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

Purchased a Maytag based on previous models that worked. Now when I do a load of wash, no matter how large or small, the clothes are still wet after the full spin cycle is finished. This has been going on for a few months. There are only two adults so the machine is not in constant use. We have had the machine 9 years and frankly would never buy Maytag again.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

I have done absolutely nothing to this dryer except keep the lint screen clean. Have had it for 15 years. Keeps on tickin. It is used daily. Sometimes 3-4 times a day. The outside looks rough. But who cares. I bought a new lg washer with great looks and had it just a year and 2 weeks. Had to spend another $200 on it. Still doesnt work right. Im Maytag all the way!!! It is a simple dryer. But it is a workhorse. It was a gift from my mother and have so much appreciated it. It has been an amazing piece of equipment. From now on I will only look for the maytag brand for whatever appliance I purchase.

Should have read reviews. Ill never buy another Maytag. This stove has been bad almost from start. Stove has burned marks from using broil. Repairman told me not to use broil anymore. One of eyes has been worked on 2 times; the knob does not work correctly; when you turn off, it goes past the off and keeps on going to the left. It is very hard to clean surface. I have had a few years. Company paid for one repair. They should have replaced stove from beginning. Not safe.

I purchased a small (14.5 cubic feet) refrigerator for my basement from Home Depot on January 26, 2013. It was delivered on January 30, 2013. On February 14, 2013, we found that it was not cooling like it was supposed to. The soft drinks in it were not cold. I called Home Depot and was told I had to call Maytag for a repairman to come out. Since it was so new, I felt it should be replaced. They disagree. The warranty only calls for repair. So a repairman came out on Feb. 19th. He said that it has no freon. He doesnt know why. It could have a leak. It could have leaked out in the warehouse. There is no way to know this. He said another repairman would be out to fix it on the 20th. On the 20th, no one showed up or called. I called the repair company, S & S Appliance of Bessemer. I was told the repairman that I needed is in Montgomery today and the repairman yesterday was told to tell me he would call me. He was told to not tell me someone would be out today. So now, I have to wait until tomorrow for someone else to call me and see when he can fit me in his schedule. I think Maytag has a problem with their refrigerators. I think Home Depot has a problem not standing behind what they sell. I think S & S has a problem with their servicemen. I am not happy with any of these companies and will never buy another Maytag refrigerator or washer, but thats another story.

I have a Maytag dishwasher and the rollers for the racks are failing due to heat: plastic wheels breaking up. $35 each to buy and replace. There are eight total. So $280 because of poor testing and quality of materials. Manufacturers should test to ensure the parts last a reasonable period of time and are designed for the environment in which they are being used.

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

Replacing a working but noisy 14 year old Sears dishwasher for the newer Maytag was my bone head move for 2011. It died the first year control panel shot, no warranty. Paid for repair. This month dead again; same problem. Recall this stainless steel garbage. Maytag model MDBH949. Maytag, never again. Bought twice and last time.

Maytag Washer was bought on May 2010 for $746.29 and it broke down. It was used only twice a week. It now requires repairs worth $991.36. All Maytag reps say is I am sorry, there is nothing we can do. Isnt there a lemon law for major appliances?

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.

I had a Kenmore that lasted 20 years. This didnt last 5. Paid a lot of money for a disposable washer. Red in color on top of that. When I bought I did my research and had good reviews. Dont buy any new technology -- not enough data. This a POS. No more Maytag for me. Spoke to a repairman -- water leaking from the bottom and bearings are out -- was told it was a bad design. 951.00 -- energy guide said the annual cost to operate was 30.00 a year -- my calculation is 30.00 + 190.00 = 220.00. What a ripoff. Never a Maytag for me again. I only really needed a dryer but thought that I would update and just get a matching set for my women. Now we will be going back to an unmatched set. What a terrible purchase. Review says 5 star -- that is for the Consumer Affairs -- not the washer.

Purchased a Maytag refrigerator in July 2011. The compressor failed May of 2013. After many phone calls to Maytag they replaced the parts (compressor) - my cost for labor (aprox $300.00). 30 days later, the service company had to repair a leak and recharge the system. March of 2015 the compressor failed again. Have spoken to Maytag (case # **) - they will provide no help what so ever. I was told I should have purchased an extended warranty.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

This Maytag Bravos is the worst washing machine I have ever had. Who ever heard of washing with almost no water? Takes way too long. Clothes not clean. Any water savings way offset by ridiculous length of washing time. I can wash and dry a load of clothes in an old stacking washer/dryer before one finishes washing in this thing. I was excited to get it and now cant wait for it to go. Wont make this mistake again.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

I purchased my Maytag Neptune pair on Jan. 24, 2005. I was unaware of the problems and lawsuit related to these items. Luckily, I didnt have any problems with them until May of this year. At that time, I spent $337.00 for a new control panel for the dryer. (Just because I didnt want to split up my set.) I expected them to last me for the rest of my life. Of course, the washer had started to do something even the repair man had never heard of before, right about the same time. I told him that the tub would fill up with gallons of water, and surprise me when I opened the door on various occasions, flooding my laundry room and the basement downstairs. Mind you, this would occur even with the water supply cut off to the machine, no hot or cold running to it.He performed a diagnostic test on it and said everything showed up fine. Of course, it didnt overflow while he was here. He is the one who told me about all the trouble and the lawsuits. I had wondered why I didnt see them for sale anymore. I have been keeping the water turned off except when I need to use it after all this time. It still happens! The repairman thought I was senile or something. I dont have a mold problem, no trouble with the door lock (yet), and out of all the comments and complaints Ive read online today, only this site had one with a problem of it flooding the house. My husband and I are on a fixed income, and here is this unit (that I thought would be my last) rotting out my floor and wall in the laundry room, and flooding my basement. Not to mention it rusting out the inside of the washer and its pedestal. I would like to hear from anyone else who had this water problem, and what it took to fix it.

We just purchased a house with new appliances. They are Maytag. When I use my stove the oven heats. I have no idea why. I wondered if anyone else has had this problem. When I turn it off it turned off but it turns back on when the oven is on.

Nothing wrong with this dishwasher, a bit noisy, but it gets the dishes clean and thats whats important. This was a builder grade installation and it came with the house so I cant really say its the exact model I would have selected had I been given the opportunity to pick my own.

Dishwasher Model #MDB7609AWW2 - I have replaced the touchpad once a year for 4 years. Went online and learned a DIY repair using a Permatex Rear Window Defogger Repair Kit to fill in the touchpad broken circuits. I have repaired it once a year for 2 years. My suggestion is to avoid purchasing this product. Apparently even after multiple consumers have contacted Maytag regarding this widespread defect, Maytag has not issued a recall or assisted anyone. They say if the part can be replaced there is no issue. When the dishwasher works, it is great, however it WILL NOT last. Touchpad will fail and you will be out $124 for the part plus labor unless you do the repair yourself.

Maytag Centennial Commercial washer - We purchased this washer approx 4 years ago and have never been satisfied with the job it does. Most loads require a second rinse cycle and then perhaps not a good job on the clothes. We have had it repaired twice as it makes a god awful noise and does not do a wash cycle. I believe the repairman has replaced plastic pulleys both times and now it needs the repair job done again. High efficiency has led to high disappointment. We will be looking at getting an older style agitator model as we know they work! Maytag will have to pay us to buy anymore of their products, not impressed at all.

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

The washer does not wash good on the initial wash. I have to wash my clothing twice. Cost and time consuming. The washer is “HE” and the water level is never enough. My clothes be saturated with dirt/lint scum and I never overload my washer. HELP!!!

We are extremely frustrated with this machine. It takes an extremely long time to go through the cycle, compared to past washing machines, even when it is working. It rarely completes the cycle and often goes back to wash and stops. We have no way of knowing if it washed or rinsed or what. To get it to finish, we have to turn the dial to drain and spin. The clothes always come out tightly twisted and tangled up and have to be untwisted and items pulled from each other....so they are extremely wrinkled! This is the first and last Maytag product we will ever buy. We HATE it!!! I would say it has been a lemon from day one but Home Hardware was no help when we complained. We tell everyone to stay away from this product.

Bought Bravos XL washer/dryer from Home Depot in November 2014; installed 12/8/14. First repair was in March 2015! Clean machine cycle quit working properly on 3rd attempt. Bearings were replaced, tub was replaced and main board was replaced all before May 2015. Wash load constantly becomes unbalanced if more than 3 bath towels are in the load or more than 2 pairs of jeans. Can not start a load of wash and leave home because the machine will start bouncing and rocking when unbalanced and will shut down after it tries to self-balance 3 times. You end up with a load of twisted up, totally wet mangled clothes. Maytag refused to replace the machine and Home Depot continues to sell this junk to unsuspecting buyers. Wish I had looked at reviews before I bought this model. Worst $1,200 Ive ever spent. I have always bought Maytag appliances--refrig, stove, dishwasher, microwave, other washers--but Maytag has lost me as a customer after this experience with them. Terrible design and poor customer service for not standing behind their products.

You can not add water to the fill, blankets dont even get wet when you wash them, you can do double rinse but cant control the fill, have to sit there and lift the lid up and down for 20 minutes to get enough water in the machine! The washing machines have turned into absolute garbage! Wish I would have come here first, whats the difference if I control the load size water or IF I SELECT DOUBLE RINSE? THIS WASHER 200% GUARANTEED I WILL NEVER BUY A MAYTAG AGAIN. ABSOLUTE TRASH FOR $700.

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

My experience is very similar to Richards below. I have an MDBH979AWS3 that was purchased new in April of 2010. Just over one month after my warranty expired, the touch panel ceased to work. Since it was no longer in warranty, I had to replace it out of pocket. The wiring harness to the old panel looked heat damaged. Last winter, the central computer died. The machine was useless. I called Maytag customer service and actually seemed to find a sympathetic ear. They agreed to a new part if I paid $129 for one of the two companies doing certified repair to install it. During the summer, it blew several fuses. Then in late November of this year, the touch panel went again. I hesitated on how to respond and waited until after the holidays to call them. I got the most rude customer service rep that Ive dealt with in a long time. Somehow, I was blamed for a misdiagnosis on the computer panel (duh, no, that was a different issue and it was indeed broken), accused of misuse of the dishwasher, and flatly told that they werent going to do anything more on a machine. So far, out of warranty. Im sorry, but I cant accept that a machine under 3 years old should have 3 major failures. Maytag has to step up and at least look at this problem. From what Ive read, this is a common problem that has resulted in several fires. Maytag has to know about this and continues to do nothing, not even issue a recall on the current touch panel used. I am now faced with putting another $100 in (which puts me at about $350 total on a machine I paid almost $500 for) or just buy a new product. Rest assured I will never buy another Maytag-Whirlpool appliance.

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

Bought this washer back in March of 2016. This is the biggest piece of garbage that I ever came across! That washer does not clean clothes, when they are dirty. If I stand in the rain dressed in dirty clothes, they get cleaner than in the washing machine. In 5 month I have tried every possible variation of washing to no avail. I have to handwash the clothes that I wear to work in the garden, or any other dirty job, because the washing machine does not do the job! I bought that washer at ABC warehouse, I paid almost $400 for the thing, and I have to handwash my dirty clothes!!! Shame on you!!!

We purchased a Maytag front load washer and matching dryer in 2007. In 2010, the main control board of the washer broke down. We spent $450 to replace it.In 2014, the washer stopped working. The dryer started producing horrid odor when we used it. We replaced both with LG recently. We NEVER buy or recommend Maytag products. Stay away from Maytag. There are many other reliable washers and dryers in the market. This is to help other consumers.

All of my brand new white wash cloths have black stains on them. They look like mechanics use them to check the oil. And, my white denim capri pants have weird stains on them. This washing machine is a joke. It may be water efficient, but sacrifices cleanliness and stain removal. Maytag should recall this ** Queen.

I have had this dishwasher for 3 1/2 years. Replaced the touchpad 2 years ago and now the touchpad is dead. I read all the other comments that are similar to mine and am thinking to replace this junk dishwasher. I will not be buying from Home Depot as they are selling cheap products that are defective!

This is my second washer in less than 5 years, going third. No customer satisfaction. Maytag/Whirlpool dont care, Customer Service doesnt care - all I hear when I call is, “too bad”, “so sad”, “call a repairman”, so you can spend another $100.00 plus. I hope this doesnt happen with someone elses brand when we buy it. Shame on such a big company.

We spent $600 on a Maytag Jet Steam Plus dishwasher and its junk. We bought it in May of 2013 and the top panel is burnt out and the ribbon or control wires is corroded. Maytag wont pay for replacement parts and I wouldnt recommend anyone buy Maytag again. I thought it was supposedly a good brand but its nothing but garbage.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

I specifically bought the washer because it has an agitator and you have a setting for more water if you need it. My previous washer had no agitation and really miss that. Seemed like clothes got cleaner. On this machine the agitator is certainly helpful, but there is so little water sometimes I find a pair of jeans with dry spots when load is complete. No, I do not overload the machine. If I change the setting to add more water I don’t see a difference in the amount of water that comes in. I find myself frequently adding an extra rinse. I feel that while making the new washing machines eco friendly they have cut back on water conservancy too much. At the very least the consumer should have more options as to levels of water. I would not buy this brand again.

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

Add me to the list of people who hate this washing machine. It does not use enough water to get clothes really clean, leaves spots, is hard on clothes and tears them up, and the spin cycle gets unbalanced too easily. It has taken me hours to wash one load with a blanket in it because of the spin problems. I have not been able to restart the spin cycle without starting the wash cycle from the beginning.

We purchased the Bravos XL in May 2017.. It quit working on April 30, 2019. Maytag sent me a form letter that basically said I was out of luck.. that sometimes things go wrong with a product or manufacturing. The fact that it wasnt 2 years old yet meant nothing to them. I would like to join or start a class action. This washer should not be sold.

Topload Maytag Bravos washer sounds like a jet on spin cycle. Called Maytag, no recalls or service issues. Just wanted to sell me a service contract for over 300.00 dollars that would fix it and be covered under warranty for a year on anything that went wrong. Could set me up with a service call, but it was six days from now - no thanks. The washer this replaced was a Sears which was 26 years old. It still worked and I sold it for 75.00 dollars. Guess I will stick with Sears!

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

I have a 4 year old Maytag refrigerator, model F2557HE, with French doors above and freezer below. The compressor is dying, which amounts to total failure of the fridge. Periodically the compressor tries to start, there is a whirring sound that lasts and lasts and repeats as the food defrosts. Then mysteriously hours or days later it starts to run again and the melted ice cube bin turns into an iceberg. The appliance repair company tried replacing the starter to no avail, and now tells me it is the compressor itself. Each time it stops, I transfer my food to the 30 year old Whirlpool in the garage which still works fine.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

Purchased new stove from Home Depot. Was delivered damaged after I opened it. Called Maytag and they cannot get a service man there to look at it. They keep on telling me I have a 30 day unconditional warranty, yet they cannot live up to their words. Absolutely amazing. Bought the Maytag because of the 10 year warranty. Do not waste your time. Buy locally at an appliance store not big box stores. Do not buy Maytag either - service is just a bunch of well qualified talkers and key punchers. Very poor buying experience.

My refrigerator temperature control panel started flashing lights and the ice maker flap started opening and closing over and over. I checked online and there are numerous model #s doing the same thing, most all contacted Maytag, some were fixed for no charge. Some were not even though they admitted there was a defect in the electronic control panel. I was one of the ones they refused to fix because they said it was an older model but they fixed a 2006 model, a defective part is a defective part no matter the age especially if they know and admit there is a problem with the control panel.I cant understand why they wont take care of their problem, so now I have to spend over $300.00 to fix a problem that they made in manufacturing, that is not an outrageous amount, thank goodness, but I just dont understand why they wont stand behind their product when they can fix out for probably half that cost to take care of their problem. I didnt make the refrigerator, they did.

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

Does a good job of cleaning but takes much longer to complete. Pretty much standard features. Has rinse only cycle, air dry only cycle, and cycle for pots and pans. Top rack had special holders for long stemmed glasses which I dont need. Standard size. Same size as my Kitchen Aid. White, front load, no special appearance. It takes much longer than my old dishwasher. Also the soap dispenser broke after 2 months and had to be replaced. It requires that two buttons have to be pushed to start. My old one only required one. It does a good job of cleaning.

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

I purchased an over the range microwave (OTR), boxing day 2018. It failed January 2021. It worked great before failing. The issue with Maytag/Whirlpool is their service. I told them before they came out that I was only interested in having it fixed if it could be done that day. They checked that they had the parts and said they could do it, so I moved forward with the appointment. Well they didnt fix it, and said that they need to order a part, which they said would take several weeks. They are trying to bill me the service fee $167, and expect me to wait a month or possibly more to get the part and fix the microwave. Now Im faced with having to pay a service fee for something not fixed and buying a new microwave. Lesson: Never try to repair, cheaper to buy a new product. Other lesson, never buy Maytag or Whirlpool product again. Despite what is on their website and advertising, they have terrible customer service.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

The Maytag Bravo Washing Machine was sold as the top of the line. In reality it is very difficult to work with for three specific reasons. First, the spin speed is too high causing the clothes to be wound into tight balls causing pilling and the need to iron everything from t-shirts to workout pants. Second, the spin speed is so high that you can only put a few towels in the washer at a time or the machine goes off kilter several times a cycle. Finally, if you lower the spin speed the items take forever to dry. I used this for less than 30 days and tried to return it but Maytag would not take it back. The only cycle type I can use is the rapid wash unless I want to spend all day washing and drying one load. I hate this washer more than I can describe and will NEVER purchase another Maytag product. It absolutely ruins your clothes and Maytag takes no responsibility for making a very bad product.

We have had this machine for too long. It starts banging and making tremendous amounts of noise. We have balanced it and tried loading it in different ways but when it starts to spin it apparently tries to even the load somehow that results in very loud noises and movement of the washer in the laundry room. Terrible machine. If we could afford it we would trash this one in a heartbeat and buy a different brand.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

This washer is the worst! Dont buy it! I paid a huge amount of money only to have it break down in 3 years! My husband and I live without children so our use is minimal. The spin cycle started to make a noise sounding like an airplane taking off. The repairman said it could be fixed for $800 and his service call, he told me that there were over 2400 complaints with this washer for the same product. He also told me not to use it while Im out to avoid the risk of flooding my home! Save your money and DONT BUY MAYTAG products.

2016 model washer. Bought a Maytag in 2016. Replaced in 2020. Problems: Spin cycle extremely noisy, have to close the door to utility room to stay in the house. Leaks a lot during wash cycle. Getting the lock to release takes awhile, sometimes I have to unplug it. Makes a grinding noise at times when starting the spin then.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

I bought a Maytag front load washing machine. We paid $1,100 for this machine. About a month ago, it was making a loud noise. I called them and they said were going to come out and fix it. However, our washing machine did not have a serial number. It had the model number/purchase date, etc, but no serial number. Our drier had it, but not our washing machine. All Appliances stated they could not help us until we had a serial number. We spent around 3 hours on the phone with Maytag, trying to get a serial number. Melinda informed us that we were out of luck, and that there was nothing they could do for us. She stated to call Nebraska Furniture Mart, to get the serial number. We did. NFM does not keep serial numbers. They keep model numbers, and purchase dates, but not the serial number. I called Maytag back, and spoke with Arthur. Within 10 minutes, he gave me a serial number to use. Interesting. In the meantime, I have been without a washing machine for 2 days. I have a load of wash in the machine, because now the wash machine has gotten so bad it is shorting the breaker, and not allowing electricity to the machine. This caused the front door to lock and shut down. Inside the washing machine is a load of clothes. All Appliances now has the serial number to order the parts. The parts were supposed to be here yesterday, Jan. 9th. Surprise, they are on back order until Jan. 13th. I called Maytag to see what they could do regarding me without a washing machine for over 5 days, which could turn into 2 weeks. They simply replied that it takes time to order parts, and there is nothing they can do and apologized. I asked what about me having to go to a laundromat and sit for hours, doing laundry. What about sending me out a loaner, to do laundry until you can get the parts. They again replied; there is nothing they can do.I also stated I spent $1,100 for this front load top of the line, Maytag washing machine, because of its name, and supposedly good quality. They again said there was nothing they could do. They did tell me that the washing tub, the part that we needed, was on back order until January 28th. This puts me at about a month without a washing machine. They stated they would try and locate the part, and have it sent out to my house, not the appliance company that is supposed to fix it, but my house, so that once I did receive it, I could call All Appliances, and set up the time/fixing of the machine. This has been pure hell! Maytag is a joke. I paid a good price for a supposedly good company/machine. They are doing nothing to expedite the parts. They are doing nothing to back their products. They are not even offering compensation for my inconvenience of having to go to a laundromat, or being without a washing machine for over a week, and potentially up to a month.I have been without a washing machine for over a week. I have had a load of laundry locked in the washing machine. I have had to drive to a laundromat to do laundry, which includes time and mileage. I have been informed that the parts are on back order, and now could be up to a month without a washing machine. Maytag is not offering any compensation, no loaner machine, no replacement. Instead, they are just saying, sorry, you have to wait for the parts. I would really like the VPs. and Presidents of Maytag to go without a washing machine for a week, or their families to go without a washing machine for a week, possibly a month, and see what they have to say about that company.

The range I have works awesome, which is surprising for an electric stove. For being 11 years old I am happy with how it is still holding up. The only thing I would improve is if it was a double oven instead of a single!

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

Washer knots clothes into unmanageable tangle. Poor rinse leaves soap scum unless rinse extra, thus not conserving water as appliance is supposed to do. Load easily becomes unbalanced and unable to restart machine if paused to rebalance load. Will never buy another Maytag washer or dryer.

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

I purchased a Maytag Bravos XL at the end of June 2013 because my washer of 14 years finally quit. On the 2nd load of laundry I ran, the machine began making a terrible grinding noise. It sounds as if I am washing a load of rocks while its on the wash cycle. I immediately called the local store I purchased it from and they sent a technician out to look at the machine. He couldnt figure out why it was making this noise, so he called Maytags techs for assistance. They had him run a battery of tests and they finally determined they needed to replace the motor. Are you kidding me? On a brand new machine?! Now Im thinking I have a lemon for sure. They replaced the motor and the machine continues to make the same noise. Ive called Maytags Customer Service to let them know about the garbage theyre producing and all I got was attitude. The warranty only covers parts and does not replace machines, so Im stuck in the song and dance of lets try to figure this out and see how they can make this piece of junk work. I then asked to speak to a manager. She offered me a 6 month extended warranty for free. I guess thats a big sign that Im going to need it since what they are producing is garbage. Whatever happened to customer satisfaction? Its now just the too bad attitude. Now, I feel like Im being held hostage by my machine because I have to take time off of work for appointments with service technicians. Wheres Maytags compensation for my time and the hassle of having to deal with this? I paid $1000 for something and I guess its too much to ask for it to actually work. I am all for buying American (the machine had a sticker, proudly made in Ohio) but if this is the quality of work that they are producing they should be embarrassed to work for this company. I will never buy a Maytag again and am making it my mission to warn others of my expensive mistake!