Top rack fell off with load of dishes. Clips that hold rack to slides broke. Week for repairman, two days for parts, week for repairman. No repairman, call parts be in on 7/28 2014, repairman on 7/31/2014. ONLY HAD DISHER FOR A WEEK, NOW IT IS BROKE. WHAT A RIPOFF.

Some difficulty in cleaning the range around the burners when spatters occur, no matter what you use it is very tight to get around the actual burner to remove that residue. I have tried many approaches and several types of cleaners to get the residue marks off the brushed stainless surface.

My machine is only 14 months old and will not even turn on. I opened the lid, and the tub was filled with water and the wet clothes sitting in there. There were only 6 items in there: 3 school skirts and 3 school pants, dripping wet. So I unplugged the unit to try and clear the circuit board - to no avail. The machine will still not turn on. The lights are on, the sensor turns on for about 3 seconds and shut off and everything just sits there. I did not get the extended warranty. My mom still has her Maytag she bought 30 years ago and its running like a champ. Wish I could say the same. I gave my sister my old Maytag - its 25 years old and its still running like a champ. This machine is a LEMON. I will never buy another Maytag again. I am so done with this brand. I hope that a Class Action suit is filed against them.

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

We bought a Maytag Neptune Washer and dryer package from Home Depot in 2004 and had nothing but problems ever since. Such things as washer had mold constantly. Also, clothes seemed to have a foul odor after washing. The dryer always seemed to have to be ran twice to get clothes dry.

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

We bought the fridge (MFF2258VEW2) about 5 years ago. We have had nothing but problems. First it was the water leaking all over the floor. The repair man said the drain tube in the back was too small. That was replaced. Then the door gaskets were replaced. The doors still do not stay closed. Again water leaking all over the floor. The bottom of freezer had ice all over it. I had to take the back of the fridge and freezer. For 2 days I had a fan blowing on to defrost it. The door shelves are cracked and falling off. I had to pay for the hooks that hold up the bottom shelf 5 times and again they are broken. The long narrow slide out shelf is broken. Food in the back of the fridge are freezing. I have contacted Maytag a lot and they will not fix the problems. At the same time I bought the fridge I bought a Maytag top load HE washer and a drier. I had to throw out the washing machine last year. It would have cost me too much money to fix it. I will never EVER buy Maytag again.

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

One year ago I bought a Maytag Micro-wave and a Maytag dishwasher - big mistake. I should have done some homework. I had problems with the dishwasher since the day it was installed. I should have suspected something was wrong when it was delivered. I opened my front door and there stood a deliveryman holding my dishwasher in his arms. He said, Where do you want it? I couldnt believe he could be carrying it by himself, especially since it took three of us to move out the old Thermador which by the way was still working just fine after almost 30 years. But my wife insisted on a new washer for her new kitchen. The Thermador was actually made of steel. The new Maytag was made of plastic even the motor. It had some steel and copper parts but mostly plastic. I dont think it weighed forty pounds. The problems began the first day with leaks through the door and under it. I suppose eight or nine service calls happened in the next 3 months. The factory service men were different each time and each had their own guess as to what caused the leaks. Over time they replaced all the parts that could be leaking some of them twice, because subsequent servicemen discovered that a previous service man had installed the wrong parts. We often had to wait several weeks because replacement parts were not on hand, and would be ordered and shipped directly to us. Then we would have to schedule another service call, only to find out the wrong parts came - more delays. One service man told us we were using the wrong detergent, even though it was the detergent and spot-free rinse that came with it. Another service man removed the door cover so he could watch to see where it was leaking when it operated. He said the soap was foaming too much and flooding over, so we had to try another brand of soap, even though by now we had accumulated three other brands that were just barely used. The service men never did fix the problem. It took much experimentation from my wife to stop the leaks, which meant we could only use a fraction of the recommended amount soap. By now we were using so little soap that the dishes always came out dirty. So our choice was mop up a wet floor or have dirty dishes every time. Most of the time now we wash the dishes in the sink. One service man said in Maytags effort to make the dishwashers more efficient, and less expensive to build that the motor and pump were way under powered, and everything was made from petro-chemical by-products (cheap plastic) and that we should invest in the extended warranty. Its cheaper than paying service calls when the warranty runs out soon. What we should have done was exchanged it for another brand. My wife said had she only known, we would have never replaced the old Thermador which will be my next dishwasher. As for the micro-wave there are many things I dislike about it especially the rectangle glass tray which is extremely awkward to remove and replace each time you have to clean out crumbs and spills which happen often. The timer on/off bell is way too quiet with no volume control. The message and operation display is difficult to understand. And to top it off the cheap plastic handle broke one week after the warranty ran out which I found out that its less expensive to buy a whole new door than pay for parts and a service call to repair handle. Maytags track record made me not want to deal with service dept. again. I will probably be money ahead to trash the two appliances, start over and do some homework and maybe buy a European made appliance. I know German technology is not all about profit making, but quality, reliability, durability. I hate to sound un-American but greed in American corporations will be their downfall.

I purchased my Maytag washing machine in June 2011 and within the first couple of uses, noticed that my clothes did not appear clean. I went back to Home Depot and complained and was told I had to use HE laundry detergent and I was. I gave it a while longer and still, nothing I washed ever seemed to come out clean. Sometimes, the fabric softener dispenser fills with water; other times the fabric softener remains in the dispenser. The machine makes very loud clunking noises during the wash cycle. I knew this machine was a lemon from the get-go. I should have insisted that Home Depot come take it away. I will never buy a Maytag appliance again! Maytag should have recalled this washer long ago and, if there was a Class Action law suit, I would surely join in!

Im told even though my fridge is leaking water and making sizzling sound nothing can be done and my model number and serial number match the recall for this product and I was told that if my fridge catches fire then, Call us but to me thats ridiculous.

I bought a Maytag dishwasher (MDB7749SBM) and 1 yr and 4 months the control panel went out and all Maytag would do is tell me that they will pay for the parts, and I have to pay for the labor. I remember when Maytag had the best Warranty on their appliances. I am very disappointing with paying for labor. They also offer an extended plan of $269.00 for a year. What a joke!!!

We purchased this machine (Bravos XL top load washer) in August and its been nothing short of a disaster. It doesnt clean anything. Within two washes my cloth diapers were unusable, loaded with ammonia and stains. Our camping clothes wreaked of smoke. I tried multiple cycles, more detergent, less detergent, larger loads, smaller loads. Doesnt matter. It doesnt clean. I called customer service within a week and waited 6 weeks for a service call. Into third trimester of pregnancy and recovering from an MVA, I was washing soiled clothing by hand in bathtub desperate for help. I only wish Id known about their 30 day money back guarantee. After many calls, no shows and cancelled appointments, the first tech comes. He tells me the machine is fine. They just dont clean well. Hes not surprised. I call the appliance shop, they said the same thing. That they wouldnt have sold me the machine if they knew I had dirty laundry to wash. (Who washes clean laundry?). They wont help us. We call Maytag back. They send another tech. He says the same thing. Tells us to keep complaining to Maytag. I call again and they tell me that if I want a service tech, I have to pay. Theyve deleted all my feedback from their social media site and refuse to provide any assistance. The machine is nice looking and makes big promises but thats where it ends. Save your money. Youll get better results with your grandmas washboard.

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

The new Maytag commercial brand is different than the traditional Maytags. Uses less water. The new technology in the variety of choices for cycles and the steam cleaning for the dryer is a great feature.

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

It’s a nice look to your kitchen first, and an easy clean. Works great for heating up stuff in a hurry and makes popcorn perfect on the popcorn button. Does ok at melting things. I have been happy with mine for 3 yrs so far.

I like Maytag but my low water no agitator washer does not do the job as well as it could. Also if a coin gets in the washer it is very hard to get out of the crevasse in the tub area. Most people from time to time have some change ending up in the washer...it should be easier to retrieve.

I love the fact that there is no agitator in this machine. It give lots of room when washing bulky comforters. I also love the vast amount of settings for load size and the soil settings. The con of this washer is that it has broken down on us twice in the 2 years since we purchased it. The pump has gone out both times. Unfortunately it looks like we will be making a purchase of a new washer in the near future because another mechanical issue has arose.

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

Bought new Maytag French Door with cooling drawer refrigerator in July, & have had nothing but problems with both product & customer service since. Have already had 2 service calls for the SAME problem. The in-door ice maker/dispenser is a horrendous mess. Place a container below the opening to get ice cubes & ice is sprayed in chunks all over the floor & around the kitchen. To get ice, you have to put the container in direct contact with the opening, & then place a towel over the entire in-door unit to keep ice chunks from spraying all over the floor. The unit has a small flap-door in the ice maker, which must open & close automatically when getting ice, but the flap failed to close, so the ice in the ice maker was melting & the water running into the refrigerator unit & onto the floor. Called warranty repair & they came out & said they fixed the door-flap, but they did not. Ice was still melting & the freezer unit would not even keep ice cream & pastry items frozen solid. Called repair a 2nd time during the first 4 months of ownership, & they came out & replaced the motor to the small door-flap in the in-door ice/water unit. When asked why the freezer would not keep ice cream & pastry items frozen solid, the repairman stated (quote): Freezers dont keep ice cream frozen solid because it has so much sugar in it, its like alcohol. Had no excuse about the pastry issue however. We replaced a 12-year-old Jenn-Air with this piece of junk, but at least the Jenn-Air kept ice & ice cream frozen solid, & the ice maker did not leak & spray ice around the kitchen. Jenn-Air must know something about freezing sugary ice cream, that Maytag/Whirlpool do not understand. Then today we got a notice that Whirlpool had denied payment for the 1st repair visit, even though the unit was only 2 months old then. As such, we expect them to deny payment for this 2nd visit, even though the unit is now only 4 months old. Bad product & sloppy customer service, from a company with ZERO consumer support.

Maytag Top Loading Washer-We bought this machine a little over a year ago and it is one of the worst products weve ever purchased. More often than not clothes barely get wet and then wad up into a twisted mess which stops the machine. Ive had to restart a load over and over. And, the clothes are not as clean as they were from our former Maytag washer which lasted 14 years. The new washer has to be cleaned at least once a month or it smells. We purchased this washer from HHGregg and they are no longer in business or I would complain to them about selling faulty products. I dont know why the manufacturer decided to remove the agitator from new models. What a mistake! We have decided to get rid of this washer and buy another brand. No more Maytag (or Whirlpool) products... ever!

I purchased a refrigerator in Aug. 2012 from Home Depot. In June 2013, it broke. I contacted Maytag/Whirlpool and they had three companies come out to try and fix it over a four-week period when finally it was determined that it was unrepairable. Now I was told that we can get an exchange but now they have the incorrect delivery address and the person supposed to be handling my case has been on vacation and I left several messages. I contacted Maytag for someone else to help and cant seem to get anyone for the past 2 weeks. This has cost me money for food lost, time from work and time making calls.

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

Unsafe Maytag - We have had lousy service from our last purchase of a Maytag Atlantis washer and dryer. The washer failed after 14 months, and since it was more expensive to repair it, we replaced it. I needed to do a simple repair to the dryer today, and I had to take the front of the machine off. I found the inside too so full of lint. I believe it was only days away from catching fire. The blanket of lint I removed from the top of the heating element appeared to be charred and black, a fire ready to start in my opinion. I will not have this machine repaired. I want this fire trap out of my house. Before you ask, I must add, my wife cleaned the lint trap often. The Maytag Company has not been helpful. I will add that our first set of Maytags gave us many years of good dependable service. What happened to this company?

I wish I had read the reviews before selecting this Bravos XL washing machine. I bought these from Conns Appliance as they were on sale 750. Rounded figure... They were delivered today and the company was professional and set them up, I have spent the last 4 hours washing the same medium load of childrens clothes trying to get them clean. Ive even separated them into smaller loads and am now into the 5th hour of laundering this same load... Im returning them but its gonna cost me 15% restocking fee. If theres a class action please count me in. I thought because our Maytag Neptune lasted so long wed have a great outcome again with these, boy were we WRONG!

I bought a new Maytag stove and it is less than two years old and the oven has already quit working. It only has a one year warranty and will cost about $200 to fix. I am very dissatisfied with what I thought was a good product.

My wife and I purchased new Maytag dishwasher in 2011. Worked well for 9 months and then control panel went out. We bought a Sears with 1 year warranty. Sears fixed but then 2 more repairs followed with blown fuse and pump motor went out. We knew this was a lemon so we purchased an extended 3-year warranty through Maytag. Well the unit only works for a month or two then we are constantly calling for repairs. We just had the pump replaced a 3rd time and yep you guessed it the unit is loud again so here comes repair 15. The warranty contract states that if the same part fails 3 times, Maytag will replace the unit new one time and voids any further repairs. My wife and I are very frustrated and lost all confidence with the Maytag company. Our old one lasted 14 years and this new one is a piece of junk. The company reviewed my request of unit replacement but was denied for whatever stupid reason. This unit has over 5000 dollars worth of repairs not counting the lost time of appointments waiting for the repair. My wife has had to stay home and wait for 4 to 8 hours an appointment. She has many other obligations to do with her time. Its sad that Maytag does not stand behind their product. Its my conclusion that this company does not want to sell good product, they only want to sell extended warranties. Your products are not reliable if you have to offer warranties. I would like to see if I can get to repair 30 before my warranty expires by March of 2015. Maybe I could then see if 30 repairs would make the Guinness Book of Records on the most repairs done on a dishwasher with extended warranty. That would be something the company could be proud of dont ya think.

Purchased a new side by side American made Maytag refrigerator (Model: MSD2559XVEB ) in August 2010 from Best Buy. Just returned from a 3 week vacation and the refrigerator died shortly after we left on trip ( 14 months post purchase date ). $700 worth of food ruined.

This is a review of a washer that is no longer sold. I bought a top of the line Maytag washer 45 years ago. After around 25 years the control (all mechanical) started sticking during the cycle. I opened it up, sprayed it with TV Tuner cleaner, worked it a few times, and it has worked perfectly ever since. That is the only problem or repair on that machine since it was purchased!

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

It takes almost a whole day to wash 1 load of clothes. The clothes dont get clean! The spin cycle wont let you spin. It runs your electric bill up! This is not a energy saver! I am so angry and disappointed! I thought Maytag was Supposed to be the best. Yall failed me. I wish I could get my money back!

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

On February 2006, I purchased a Maytag Quiet Series 300 Dishwasher and on July 2007, a motor leak. Maytag fixed it for free even though it was out of warranty. Thereafter (December 2008), the touch pad failed and I replaced it for $50. It is now August 2011, and that new touch pad is bad again, and this time, the part is $170. The Maytag will not run and the lighted display will not function from the start button. This was a $450 dishwasher that is now only five years old and useless.In all fairness to Maytag, their customer service is very good and willing to work with customers. Unfortunately, the product is very inferior in my opinion. To have stupid stuff like a control touch pad failing every three years is absurd and the replacement cost makes fixing it a bad investment.I will be going out this weekend and buying a brand-new inexpensive dishwasher that is on sale for $229. This model is not a Whirlpool product but it is a name brand.

We purchased the Maytag Atlantis used (4 years old); it looked like new. When I opened the lid, I noticed a terrible smell like some left the clothes in the washer for days. I used white vinegar, baking soda, bleach, anything to try and get rid of the smell. Nothing worked. Finally, my husband took out the agitator and then the drum. Inside and around the drum was lint from all the years of washing clothes. He scraped it all off and bleached it and put it back together and it was okay for a while. It now smells again and I am afraid we will have to keep doing this or our clothes will always smell. I also leave the lid open after a wash so Im not attacked by the smell when we open it. I also had the Maytag Neptune front loader years ago, and the water pooled by the gasket on the door. That smelled too! We will be redoing our laundry area soon and will be shopping for a new washer and dryer. It will not be a Maytag!

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

Purchased Maytag dishwasher model # MDBH979SAM1 on February 8, 2014. 6 months in paint came off door. Added 5 year extended warranty on 4/21/2015. Dishwasher started not working properly on 9/24/2015. Hit one button but a different would light up until finally on 10/2/2015 it quit working. Called for service On 10/2/2015 10:30 pm no answer. Tried again on 10/3/15 same answer. Tried again on 10-5-15 finally answered and they called repairman. No answer but they gave me his number so I could call him if he didnt call. Finally called him and He told me he was busy and could not come repair my dishwasher. I called MaytagNed they said he would come. When I called he said he was not coming. He had truck trouble. 10-12-15 Called Maytag back and they said they would find another repairman. They would call me back. Into 2 weeks waiting on appointment. I will never buy Maytag again. It didnt clean dishes good when it did work!

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

We have a Maytag Dishwasher Model MDBH949AWB. We have purchased the extended warranty. Today, after more than 100 minutes on the phone, mostly on hold, we were unable to schedule an appointment to replace the control board, or even have them verify that we have extended warranty coverage. It generally took many many minutes to get a person, only to be referred to a different person at a different number. Nobody had access to our extended warranty info, and to go further into getting a repair scheduled, they said they needed that info. I finally went on their website, and after keying in extensive information, I got a screen saying they were having trouble with their website, and to please try again later. So I did their chat, and ultimately they told me to call 866-730-6094. The earlier numbers I called, in sequence, were 866-576-1660 (53 minutes on hold); then told to call 866-265-0029, for another long hold. And then told to call 800-626-4342. Long hold, and I hung up. At one point, I think the second person I actually spoke with gave me an incident number of **. My extended warranty expires in Feb. of 2017, and they even asked me to renew early. Since the warranty seems totally worthless, why would I do that? Terrible customer service. Wont do business with Maytag ever again, and am warning others not do so either.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

Received new washer & dryer on Oct 2nd, 2015. The dryer has been acceptable, but the washer has been one problem after another. First of all the washer is so noisy beyond belief. The engineering is one dreadful design. At first attempted use, washer would not begin cycle. Sensor would say lock, unlock, lock, unlock for so long, I would cancel & begin again. It became such an annoyance that I placed start of cycle on a timer (it sat at sensor mode for 20 min.) then I restarted next time sat for 15 minutes without starting. After beginning from start position it would start OR NOT. First repairmen told me timer might be off a bit. As days passed with same issue, second repairmen arrived and found that door was off (not completely closing). Repairmen would place an order for new seal. Upon repairmen arriving for third time (new seal did not solve issue) he believes that lid is uneven, & he will order a new lid & return in a few days to repair. I must admit that service has been quick, but the issue is still a headache. I would NEVER recommend this model to anyone and would like for Maytag to replace washer with a different model. The noise is a factor that no one should have to endure. The grinding noise can be heard from three rooms away from laundry area with laundry room door closed! Im absolutely a very very unhappy customer.

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

We have had our side by side Kenmore for years and it hasnt let us down! We eat mostly fresh food since we cook a lot and we always have plenty of space for our food. We are only a family of 2 though. They say the ice maker is the first to fail and it has not given us any issues for nearly 10 years now! Love Kenmore!

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

This has nothing to do with the vendor. This is clearly shoddy workmanship on the part of Maytag. I bought this refrigerator in 2005 and already the compressor is gone. So therefore, I have to replace the whole unit.What kind of ** is this? You mean to tell me that you people cant find someone to build a compressor that holds up more than a few years? Why dont you try American made and built.I am disillusioned by the whole industry. Im sure the people at the top could care less.

I purchased a Maytag Bravos XL Top Loading Washer and matching dryer in 2013. I had a repairman out to install a new screen on the dryer because the lint was spilling over into the surrounding area. The new screen has been catching most of the lint, but I still have to vacuum the surrounding area after a few loads. Also, I have to turn the dryer on two (2) cycles in order to dry most of the clothes, and the machine makes a lot of noise. Those are minor problems compared to the washer. It constantly tears holes in my towels and wash clothes. I NEVER put in a full load because the water level is so low, and it does not clean the clothes. It takes a long time to go through cycles and it is EXTREMELY noisy.I called Maytag and they said that they never heard of the problem of creating holes in towels and wash clothes, and wanted to charge me over $100 to have a repairman come out. They also said that the repairman might not find anything wrong. I feel that the washing machine is very hard on the clothes - like the salesman at Lowes said It’s like beating the clothes against a rock. The washer and dryer are JUNK, and I would not recommend these to anyone! I would trash them, but they were very expensive and we cannot afford to buy new at this time.

I had the washer repaired twice in January, once in April and again in August, the same repair wire coming out of harness. I had to pay a second time before Willie, the repairman, finally put a longer wire on the harness. Maytag told me they would send a new repairman after I called to complain. All 4 times, its been the same man and it cost me money. It seems like a bait and switch with the repairman. I called both A& E and Maytag. Both refused to refund the $129 second charge because it was more than 90 days. I say its been the same issue, repairman is a scam when they dont fix it right and charge again. I had another man there who knows about repairs and finally told the repairman to change out the wire or it wouldnt have been done this time either. I do want an attorney to contact me about this as this is wrong. Im going to file a complaint with BBB.

Bravo XL - This is the worst washing machine I have ever purchased! Loved it at first but after a year or so we couldnt wash a full load without error messages. Then we couldnt even wash one pair of jeans without an error message. Called to have it repaired and $300. Later the bearing was replaced and the washer worked wonderfully once again. Less than a year later and we are back to having a non functional washer. Cannot wash anything without the error message. Customer service is absolutely no help. For such an expensive washer and supposedly a good brand, this machine is a real disappointment.

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

I bought a Maytag Top Loader March 2021, this washer machine is the worst ever. It doesnt clean your clothes, & your clothes stink horribly. BBB and an Attorney needs to compensate for our all buyers.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

This washer stops every 10 minutes, sometimes taking 3 to 4 hours to complete one spin cycle if it is completed at all. All troubles began shortly after warranty expired. NEVER EVER will I ever buy Maytag again. I make certain that I tell everyone I come in contact with about the pathetic quality of Maytag.

I purchased a Maytag top load HE Bravo 700 3 yrs ago. I only wash 3 loads of laundry a week and the bearings went bad in the washer! Maytag/Whirlpool will do nothing to help me because they say I should have purchased the extended warranty. Well there is NO WAY that I could have worn out those bearings; it was a manufacturing defect that caused them to fail and hundreds of people online all say they have the same issue. The repair cost is $400 and would only have a 90-day warranty so I might as well purchase a new washer. Home Depot (where I purchased the washer) has been very helpful and is offering me help on the purchase of a new washer, but even they could not get Maytag to do the right thing and repair my Bravo. I am going back to a none HE machine with an agitator. This has been a horrible experience and Maytag has no business putting commercials on TV that say they are dependable.

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

I bought a Maytag Gemini double oven gas range 5 burners (model MGT8885XS000), even air true convection cooking. Within 4 months, 1 of the gas valves (knobs to turn gas on with) froze. I could not turn one of the top burners off. Maytag came out and fixed it. Three months later, another one froze. Again Maytag came out and fixed it. Our warranty ended. Over the next year, all five burner valves have frozen. I called Maytag, told them what happened. The most they could do for me was to give me the part half off. So I can pay $200.00 for parts and pay for a repairman to come out and fix it. The oven cost $2,000.00. I am still paying for it. Chances are if I repaired it would break again.

Maytag model MBF1958XEQ1 frost build up and ice build up bottom freezer 2011 model. Recently refrigerator not able to stay cold. Contacted Associated Service Corp. because my fridge had a ten year warranty on the compressor only. It cost me $377 dollars to have a service tech change the circuit board and remove a rubber drain valve that was blocking the excess water drain to the evaporator tray. It is working well now but will keep looking for ice build up.

I bought a Maytag dishwasher (model MDBH945AWB3) in March 27, 2010 to replace a Kitchen Aid dishwasher that was only six years old and no longer serviceable. After a little over a year, its dead. When I try to turn it on, nothing happens. If I press the delay button, the lights come on, but in about a minute, they go off.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

I bought a new stainless steel Maytag refrigerator last year. It had a one-year warranty. Wouldnt you know, 14 months after my purchase, the icemaker stopped working. Did not take out the extended warranty, as I thought I had purchased a quality appliance. I contacted the store where I purchased it. Was told it would cost $150 to replace. I have a feeling this appliance wont last very long. Suffice it to say, I will never purchase another Maytag appliance.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

Purchased MBF1958 model refrigerator July 2012. Has had 3 major problems. 2nd time the compressor has failed. For over 1 month have been playing phone tag and given the runaround by Maytag. Never return calls when promised and get a different story with each person I speak with. After 2 service calls to diagnose a bad compressor, $69 service fee, two weeks for the replacement to come in, the third serviceman decides this is not the problem and the refrigerator cannot be fixed. Maytag has once again offered to SELL me a replacement at a discounted price. Do I really want to subject myself to the HORRENDOUS MAYTAG EXPERIENCE again?

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

I have had this washer (Maytag Bravos) less than a year and it does not clean my familys clothes at all. I have had to throw away clothes that are stained and ruined because this washer does such a poor job of washing. For the cost of this appliance, I thought it would do an excellent job, only to be disappointed. I have owned other Maytag appliances without a problem. This one is a disaster and has turned me against Maytag.

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

Totally DISGUSTED!!!! Have owned my range for several years! Love have double ovens, however it is double the repair!!!! Every year we must have the handles replaced as the connection loosens and handles fall off!

I bought this washer and dryer (Bravos MCT MA655LDY) after receiving several notices from Hydro that I was consuming more electricity than my neighbours! It was delivered March 31, 2018. On July 5th 2018 I tried to use the washer. It lasted exactly 3 months! I called The Brick who sent a technician out, he said the control had gone. Not sure what that is, but 3 months? This is absurd. I would like them to replace this washer.

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

Have had this problem since week 2 of ownership. Even on the lowest setting, food in the fridge section is freezing and Im having to throw out fresh produce weekly. Called Whirlpool service since under warranty. The very nice service man replaced the thermostat. Only a little bit better as the temps do not range quite as extreme - only 25-46 now! I am now waiting once more for a service appointment, at least 10 days. Plus in Massachusetts they will only give you a 8-5 service window. They give a robocall the night before and you are given a 8-12 or a 1-4 time for your appointment. I also have had trouble with the meat drawer falling out of the track because the upper shelf bows with the weight of a normal amount of stuff. Now the bracket has cracked and the meat drawer no longer stays on the track when it pulled out partially (such as when you need to reach in and get something). Same thing happens with the lower drawer on the right side although the bracket hasnt cracked.

I like most others have experienced the same issues with the new Maytag top load WM. In addition my new machine dances across the floor like a drunk leprechaun. After Lowes told me that with my extended warranty Id have to miss work and pay 100 bucks for a service call I emailed Maytag. Needless to say they didnt even respond. Ive have learned a few valuable lessons. Dont assume that more money means better merchandise. Made in America doesnt say much. And please dont buy Maytag.

Overall I am satisfied with my Maytag Model MDB8859AWW2. I purchased the dishwasher 06/05/201. However, the door spring squeaks. It is a grating sound.

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

I have never liked the stove because it is too small (it came with the triplex) and it has porcelain like top. One burner burns to hot, the other three mediocre, there isnt enough space between the burners and the back of the stove. It doesnt cook evenly and it really does not have a low or simmering setting. You cant set a timer for simmering because it cooks too fast. The knobs are stuck and sometimes wont light when you turn them down. The oven is okay, but could be better. Wish it had self cleaning. The broiler in no existence. Food way too close to the flames. We have had this oven since we bought the triplex back in 2011.

I purchased a Maytag gas range in the past few weeks with Aqua Lift Cleaning System. I have only cooked once when grease spattered on the walls and floor of the oven. I have used the Aqua Lift Cleaning System 5 (five!) times and the grease is still there and very sticky. This system clearly does not do what it was supposed to do. I was fortunate to have bought the appliance where I could return it; however, it has been quite a hassle and I will have to pay an additional $100 to have the old one removed and the new one installed! I feel like Maytag should reimburse me the $100 because it is obvious to me now that I have found hundreds of reports of people not being satisfied with this feature.

I have a Maytag dishwasher MDBH980AWQ10, within the 1st month of owning it there were issues. Now the electronic control panel is shot, dishwasher wont turn on. To replace it...almost the cost of what I paid, warranty has run out. In the last 7 years we have had problems with 5 various Maytag products, replaced our Maytag dishwasher which lasted 20 yrs and Maytag washer & dryer that lasted 30+ years and ran without a hitch. Maytag has not been helpful at all and their authorized service repair. A&E Repair Service is a bigger scam than they are. It is a waste of my finances and time to buy major appliances every 5 years. Each and every one of their new appliances has died shortly after all the warranties have run out. Im beyond frustrated, disgusted, and financially drained. It does not pay to be brand loyal to Maytag for they are no longer respectful nor appreciative of their customers. I would love to give corporate the opportunity to enjoy the same products that are in my home...in their homes...as well as the experience of their customer service. Last Maytag purchase for me! Is there anything that I can do in the meantime so Im not stuck with their lemons?

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

Had this front loading washer 13 months when the circuit board failed. I pitched a huge fit as Maytag wanted to charge me 75% of a new washer for the circuit board replacement. Fortunately they caved. I like how well it spins out and washes well. The door gasket is hard to keep clean. Has fresh setting so clothes do not get moldy if you leave them too long.

Our first (and last) experience buying anything made by Whirlpool. I bought a matching Maytag Series 2000 washer and dryer in February 2011. By July, the washer was at 747 take-off noise level when hitting the spin cycle. I called Whirlpool, who directed me to their local repair firm. I called them on August 2nd and had a service rep visit on August 9th. He looked a 30-second look and advised that the bearing assembly was shot and that the spin basket required replacing.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

I depend on my front loading Maytag washer. It is very reliable, does a great job of cleaning even difficult items like comforters and pillows as well as items deeply soiled. I use the many features like water temp and level, fabric type, heavy or light load, etc. The only complaint I have is that the front cover of the detergent, fabric softener and bleach drawer came off and the exterior paint on top of appliance is rusting and peeling. A stronger substance for the surface where often detergent, fabric softener and other substances are often stored and they leak.

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

This Maytag Bravos HE machine has the poorest design! It doesnt use enough water on the normal cycle so I always have to use the bulky load just to get the clothes wet. The old washers used to spin the water out thus keeping the load even. This machine drains the water first and then tries to spin an uneven load! When this happens the machine bangs loudly from side to side, stops, refills with more water and starts the whole process again until it fixes its problem or until you go shake out the entire load and reposition everything. Then it uses more water to start the process all over again. It takes twice as long to do a load of laundry.Every time I use it I say I hate this machine! This machine should have never been released without extensive testing. Maytag could have figured out all of their own problems and fixed them so we wouldnt be writing all of these bad reviews. A recall should have been done years ago and the problems all fixed. I will never buy Maytag again!

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

Good deal, recommended by dealer friend. Front loaders, high efficiency, 12 years or so. Finally needs new bearings on the washer. Replaced electronic board 5 years ago. High repair costs would be the worst which is related to low-quality construction. I expect my next pair to last as long as the last 1. Full size, not stackable but oversized drums. Relatively low water usage, lots of different settings for different loads for washing and drying, automatic water level and wrinkle guard.

I will never recommend these products to anyone! My dryer has caught on fire 4 times! Cleaned lint every time we use it! It gets caught in bottom of dryer! Just lucky enough it has not caught our house on fire it is contained in the bottom of dyer itself! Washer gets UL code all the time! Will not rinse! Have to open top and try to balance clothes out! Cant even wash a comforter alone and the same thing happens! They are junk!!! Would not recommend at all to anyone!

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.