We were replacing a 4 year old Whirlpool Duet washer (bought on recommendation from sister-in-law) that needed the third repair and was putting holes in our clothes. We had purchased the warranty (which we had never done before) so Lowes gave us the choice of machines and we decided to go with the Maytag Bravos. Lo and behold, were still getting holes in clothes. Several repairman told us the issue is common and is caused by the force of the water flowing into the machines plus the rapid spin cycle which pushes the clothes through the punched holes in the tub and the clothes catch on the metal on opposite side of the tub. Turns out sister-in-law had the same problem with her Duet and (not knowing I bought the Bravos and had the same issues) bought the Bravos and also is still getting holes. So I know its not just me.We also have problem with the machine not putting in enough water so clothes do not come out clean. In fact, a lot of stuff comes out with areas that havent even gotten wet during the wash cycle. I just want an old fashioned machine with an agitator that fills the machine fully, washes my clothes and doesnt put holes in them.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

We bought 10 18-lb washers about a year ago. They are a maintenance nightmare. For example on June 5 7 out of 10 machine were out of service. One has been down since Jan 20 and the others for various lengths of time. The guarantee for these machines has been misleading since the parts for repair are never available. We are losing business and money because of the Maytag failure to provide equipment that operates as advertised. We need help now.

After having had Maytag Highlander washer and dryer for 28 years in our early married life, and continuing to think that Maytag was a quality product, we purchased the Neptune front load washer MAH6700AWW. Let me tell you this IS NOT your mothers washer, nor is this Maytag a quality product. First it was necessary to install water pipe shock arrestors because of the water valve on washer causing shock in the waterline when it closed. The automatic Softener/detergent dispenser didnt work from day one.Coins and etc. constantly kept getting under flippers and couldnt be easily removed. I found that it was impossible to remove the plastic flipper without breaking a plastic mounting tab. On my first call to customer the Maytag Customer Loyalty Team, aka Customer Service (CS), I was told that the plastic flippers were not available as a separate part, and that the entire tub assembly with plastic flippers would need to be replaced. WHAT???????? THATS LUDICROUS. After temporarily securing the broken flipper to the tub, I thought Id call again about a week later to see if the previous answer was correct. On this call, the customer service lady (whose name I have), said the flippers are available and that she would send two at no charge. A few days later two flippers arrived, but were not the correct ones. I then decided to drill two holes in the tub and remounted the broken flipper with two stainless screws as a permanent solution.Two pumps needed to be replaced. One was replaced under warranty and one by myself. The one replaced by me was damaged by a coin that made its way from the tub to the pump. Other washer manufacturers provide a means of trapping such objects before they get to the pump. The wash cycle stopped unexpectedly numerous times without reason, after which the code 5d was displayed. I called Maytag Customer service. The representative didnt know what 5d code meant. Her suggestion was to call a service man. Again, I called later to ask and was told 5d meant excessive suds which wasnt the cause. Might this have been a control problem?There were three incidents of water discharging onto the floor from under the washer over the last two months, which caused water to cover an area of approximately 5 by 12 resulting in extensive cleanup in addition to damage to stored items. Since these occurrences were weeks apart and unpredictable, I knew the problem would be difficult, if not impossible, to diagnose, even by a serviceman. I concluded that it was probably a problem with the control; either filling too long or not emptying the tub before refilling for the next cycle. Thats when I decided to send this troublesome Maytag piece of junk to the landfill.

DO NOT BUY THIS MAYTAG REFRIGERATOR. Purchased 9-30-19. Delivered 10-4-19. 12-9-19 - Not Cooling, Called Whirlpool on hold for exactly 1 hour. 12-11-19 - Repair service here - ordered new Control Panel. 12-17-19 - New Control Panel Replaced. 1-6-20 - Freezer is not freezing. Control Panel going up and down and blinking constantly. Called Whirlpool - on hold for exactly 1 hour. They called service repair. 1-8-20 - Service Repair here and ordered 2 thermostats: 1 for freezer and 1 for refrigerator. 1-15-20 - Service Repair here to install 2 thermostats - At this time I purchased the extended warranty for $119.30 for 3 years.3-1-21 - Control Panel completely went out again. I called Whirlpool - on hold exactly 1 hour before they answer phone. I am so pissed. They call Service Repair. 3-3-21 - Service Repair here. They order new Control Panel. States these panels are continuously going out and they are having to replace them everywhere. 3-12-21 - I called Service Repair since we havent heard anything. ETA on control panel from Whirlpool is not scheduled until 3-19. I am really pissed by now.In the meantime I have been on hold with Whirlpool for 47 minutes. At exactly 1 hour being on hold, they answer my call. Im told I have to wait. There is nothing they can do. I told her we were buying ice every other day at $10.07 for 2 20# bags and they wont replace money. Told me to throw my items away and they would replace all the food for $250.00 one time during the 3 year contract period. The service is Customer service on their contract is terrible. Waiting for parts is even worse. This is a piece of crap appliance and we will never buy another Maytag.

We currently have had our Maytag washing machine for approximately 15 years. The first thing we noticed was how user friendly it was. Also, the options that came with our washing machine met all of our needs. The second thing that we were excited about was how quiet it was. Our previous washing machine could be heard at the back of the house and was constantly out of balance. The third thing we noticed was how much cleaner our clothes were. Our clothes smelled better and had less wear thus saving us money. Speaking of which, the machine is an energy saver. One of the most significant attributes I can attest to is how reliable it is. There has never been an issue that required repair services. I am sure our Maytag will be in service for years to come. c

I purchased a Maytag dishwasher in Jan 2012 at Home Depot. It ran fine for 1 and 1/2 years and was only used 2-3 times per week. I returned from vacation and now needs a new control board at a cost of $300. I felt Maytag was a reputable company and am very disappointed. I am a senior and on fixed income and now sorry I chose a Maytag. I will get it fixed this time but that is the last money I will invest in Maytag appliances and repairs. I worry that the washer and dryer will go next as they are also Maytag and are just over 1 yr old.

I purchased my Maytag Bravos washer and dryer in July 2007. As with any appliance, we always purchase the extended warranty as it usually runs about $100 on appliance. My first experience with problems was in February 2010 when the control panel went out. If I had not purchased the extended warranty, I would have been in trouble. It ran out in July 2008. It was downhill from there. In September 2010, it quit spinning; and the fabric dispenser would not work. I called again in September 2010. The tub was out of balance. In June 2011, the panel control went out again. In November 2011, it would not spin. In June 2012, the panel for control had to be changed out again. In July 2012, now the pump is leaking. And guess what, my extended warranty is up 8/1/2012. I contacted Customer Service, which said unless there was the same problem within 12 months, there was nothing they could do. Well, Im fired up. I intend on making a complaint with the Better Business Bureau and anyone else who will listen to me. I paid over $2000 for the washer and dryer, and it should last more than 5 years. This is ridiculous! When Whirlpool bought out Maytag, then the product went to crap! Dont tell me the Maytag repairman does not have anything to do now, because I know I keep him real busy. I am so tired of the companys just blowing you off when you work hard for your money and purchase a product for your family that should last at least 10 years. I am a principled person, and this is not going to go away easy. The repairman is coming next week to fix it again. I am going to give him an earful as well. The last one who came to change out the panel board (3rd time) said they had nothing but problems with this unit. Well maybe they made it that way, so when the warranty runs out, they can charge you an arm and a leg for the part and the labor to repair. I will never buy a Maytag product ever again. My next one will be the new LG washer and dryer. Talk about the lemon law. This product from what I am reading here should very well fall within that category.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

We purchased a high capacity washer (MVWB835DW), along with the matching dryer, two years ago from Lowes. This review is not about Lowes. They did the best they could to make things right. The review is about the Maytag washer (made and serviced by WhirIpool). It has been nothing short of a debacle. The first two washers did not work and had to be replaced. The third and current washer has been repaired three times, including the drum and motor. We have been without the use of the washer for over a week each time while waiting for parts and Whirlpool to approve the repair. The washer is not high capacity as advertised. Filling the drum even half way results in the washer stopping mid cycle whereupon we have to adjust the contents back into balance. In addition, the machine leaves a lint residue on dark clothing that has to be wiped off by hand. We have asked Maytag/Whirlpool to replace the machine but they say it has to fail for the same issue four times in order to qualify for replacement. We are done and will purchase another washer from a different manufacturer. It’s easy to understand why Samsung and LG have become such a dominate force in the laundry sector. Whirlpool/Maytag does not care about you or the problems with their product. Buyer beware!

MF12269VEM7 - I purchased a refrigerator in September 2013 and my ice maker stopped working within 1 month of delivery. I had the motor and ice assembly changed 3 times and over 12 service visits within the first 6 months. I had the motor and ice assembly replaced in March 2014 and they offered to extend my warranty for a year. My ice maker has stopped working again. When calling Maytag customer service, I spoke to the Supervisor who will pay for the parts but require me to pay for the service calls. As well they only have a 6-month warranty extension on file. This fridge is obviously a lemon but they will not take any ownership because I did not purchase an extended warranty! The Supervisor state he does not report to anyone and he has the final say regarding my service. I will never buy a Maytag again. A year and a half of ongoing problems and no solution.

Neptune 4000 washer - Worst washer EVER! Two weeks after we bought it sounded like a jet engine during the spin cycle. They replaced the bearing parts. Only cost us 450 in labor. One year later, again the bearing but this time we insisted on full coverage. 6 months later, here we are again! Most expensive washer in the history of washers and this is a KNOWN issue - yet Maytag gets away with it while consumers foot the bill! Ridiculous! Never again will I purchase their product and make dang sure everyone I know stays away too and everyone that hears my washer is in shock that it hasnt injured something or someone. Its only a matter of time!

Food stored next to the ice dispenser freezes. Freezer floor builds up with 1 1/2 to 2 of ice every couple of weeks, door wont close and water leaks on floor.

Maytag products are a waste of money! I purchased a Maytag Front Load Washer a couple of years ago during the Cash for Clunkers rebate where we were asked to give up our reliable machines for so called energy efficient new models. After spending over $1,000 on this fancy front load machine and having it installed, I go to use it the first time and it won’t work. It took me a month to get someone to come and repair the bad board on it. I then started to use it and after a year, the thing started making a horrible loud noise. I called the repair folks and they told me it is out of warranty. I called a local repair guy who told me that the drum is shot and that it will cost $700 to repair. So I got a total of 10 months of use out of this stupid thing. Thats $100 a month to do my laundry! I would be better of dry cleaning! I have searched the web and see that this is a common issue and that Maytag refuses to make this right. Well, I can choose to never buy a Maytag again. I hope that others will heed our advice and do the same.

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

This is March 18, 2021. I bought a Maytag washer, model MHW5630HW2, which is their high end front load washer, in early July, 2020. The machine worked fine except that out of an available 10 cycles, only two would run. The seller, which was Sears, replaced it as defective. The second machine runs all the cycles but, though leveled carefully, it rattles, screeches, walks across the floor and generally seems to be trying to tear itself apart. The repair service replaced the shock absorbers in this new machine, after a six week wait for parts. This did nothing to fix the problem. The repairman finally just said he doesnt know how to fix it. After many patient hours on the phone with Maytag, they have said I have no recourse. The machine is under warranty and I purchased, for an extra $350, a five year warranty. Both warranties are useless. Maytag refuses to stand behind their product. I live in a small town in New Mexico. There is only one repairman. He cant fix it. Sooo...if you live in a small town, or dont want to spend endless fruitless hours with repair people or on the phone with Maytag, who will ultimately tell you they just cant help you, DONT BUY THIS MACHINE.

The 2013 Maytag dishwasher panel broke 13 months after the purchase. After several phone calls and complaints they agreed to replace the panel at no charge. Since yesterday I have the same problem and need them to replace this washer. I am on a limited SS income and I am not in a position to purchase another washer after 3 yrs. My previous one lasted almost 15 yrs. This is totally unfair and I hope that Maytag replaces this entire machine, not just another repair. It will cost them a lot less to do that by either sending or having LOWES to replace this one. Thank you so much.Updated on 09/16/2016: Maytag is asking $300 to fix it and they will not replace it. So, by coincidence a friend of mine had the same problem and she did the following and I repeated these steps and now dishwasher is working. Turn off the switch or unplug, or turn off from the circuit box, your dishwasher. This cuts off electricity to the washer totally. Wait 30 seconds. Push the cancel button and hold on pressing it for 30 seconds (precisely, not less). Push then, the start button and hold on for 30 seconds again. Turn on the power and the cancel light will come on and let the cycle finish do not touch anything, until it is turned off and the light goes off by itself. Then, choose your selection for washing push start and see if it works. It did with mine and hers. Good luck and LADIES- YOU CAN DO IT, if this little old woman did it by herself.

I bought a Maytag dishwasher MDB7749AWM1 in May of 2011. Yesterday, the on button would not work, so I called a serviceman out from Maytag. He said the whole panel needs to be replaced, parts and service will cost me $240.00. What a shame. 2 months out of warranty. I had two previous Maytag dishwashers, lasted for years with no problem. The newer models are junk, do not buy them! I can see by the other complaints that they had the same problem. They do not stand behind their product. I wonder how long the new panel will last? Im done with Maytag products!

I Hate this machine. It does an inferior job and I wish I never bought it. Our Bravos XL washer was purchased in spring. It left white residue constantly on my clothes. Even WORSE, the machine wrinkled the permanent press so the clothes had to be ironed before wearing. (I rarely had this with my last washer). I used the machine settings correctly and I called the company and basically...was told, Youre out of luck. I hoped that it would improve but No Way! Dont purchase this machine, dont waste your $$$.

Bought a Maytag 4000 series washer and dryer combo for about 2100 dollars in October 2011. Had a professional look at it today since the clothes stayed wet after the spin cycle. Told us it would cost 1000 dollars to repair the washing machine. So a total write-off in barely four years. I am very disappointed.

Bought in July 2015, brand new from Lowe’s or Sears. When working to its full potential it never cleaned clothing very well, had no designated spot for detergent or softener, just bleach. Just last 3 years and it’s a piece of crap that has to be replaced. Going to argue with the company to tomorrow to get them to replace the broken transmission which may or may not be considered part of the drive motor - all **. This is a very expensive machine that didn’t last a month beyond 3 years! The 10 year warranty covers the 2 most rugged parts of any washer... the agitator never truly cleaned my clothes and now it is fused to the wash basket and cannot even be replaced without being chiseled off. Worst machine, purchase, and brand ever???

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

Eighteen months after purchasing the Maytag Bravos, I had to have the motherboard replaced. Maytag offered nothing except a list of names for repairmen in my area. Now another 18 months later, the washer gets out of balance (this is a self-balancing machine, supposedly) at least three or four times for every load. Since it is all electronic, you cant select a spin cycle without the machine adding more water into the tub. Again, this does not self-correct the out of balance problem. Trying to balance the cloths several times during a wash cycle extends the length of time it takes to wash one load on average two hours. Maytag offers no customer service or customer support. Im sure their call center is not located in any part of the United States. I will never purchase another Maytag appliance.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

I like my fridge. Its a old one and still works. Its been very reliable and have never had a problem with. I dont think I would ever purchase a different brand for Maytag is the brand for me. They last for years.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

The way the outlet line and pump are set up, the Maytag Bravos does not remove all water from the bottom leaving about 2-3 inches. Even following the monthly cleaning and care has not stopped the inside of the tub from producing MOLD. When I contact Maytag there was nothing they could do about this problem. At this point my washer is only a few years old. I attempted to clean it myself but the drum would not break free. My options are, deal with the smell of mold and mildew, Pay Maytag $250 to come out and clean it (this would need to be done every 1-2 years) or buy a new washer. NOTE: I paid about $550 for this one. I have run a few clean cycles with bleach, but I think at this point the mold has embedded itself into the plastic tub.

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

Warranty dept. will not help you! I have been told by technicians sent to service my refrigerator after it spoiled food multiple times from not staying cold. The technician flat out told me that this refrigerator cannot be fixed but they are not allowed to say that it cannot be fixed. They will not return your calls and are just flat out rude. After asking to escalate a call, the rep said the manager will call me right back in a few minutes. Hours went by and I called again five minutes before they closed to speak to someone in management at that moment. This manager told me with no hesitation that they dont always believe what their technicians say because they send out techs that are good, okay, and not good. My first question is why is Maytag confident in the people they are sending to my house time and time again that stay for three hours?! She began to get rude and disrespectful and said, Well, if you had cancer, you wouldnt believe the first thing they say... I am in awe of these remarks. How do you compare a refrigerator to cancer?! I asked for a business address and stated that I would like the address to file with the Better Business Bureau and she told me that they have all the info I need. She refused to let me speak to anyone else. This situation is uncalled for when I have the technician telling me, This refrigerator is not repairable but they wont allow me to say that and Maytag will not make this an easy process for you. Unbelievable!

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

Purchase this machine Bravo XL Top Load Washer in Dec of 2016, noticed right away every load of dark clothes comes out of the washer with a scummy lint residue on them, some of the clothes are not completely wet when you take them out of the machine. Have talked to Maytag and tried their suggestions that did not work. Seems like a canned speech reading some of the other reviews. I am just at upset with the appliance store that we purchased this from after their sales pitch how these are the best machines made, made in Ohio, great company etc..etc.. Just one run around after another.

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

After one year of service from our Maytag Jetclean Plus Dishwasher with Toughscrub the circuit board went out. I have been seeing and hearing other people complaining about this problem. We purchased this device based in large part on Maytags reputation for reliability. I am not happy with this machine. I will complain to the company and write another review based on the results. I suggest Maytag goes back to the old knobs until they can assemble and protect the circuit board, which I believe was damaged by heat and moisture.

We purchased this washer 8 months ago, and still do not have a working unit. From the very beginning of installing the new washer we had repeated F4 and E1 error codes. A technician was sent out three separate times and they replaced the ACU each time only to have the same error codes recur. This unfortunately took 5 months as each time the ACU part was on backorder. After 3 failed attempts they agreed to replace the washer with a new one. We were dumbfounded when the new unit arrived and we had the same F4 and E1 error codes! They have again replaced the ACU and still we have the same error codes! They are sending yet another ACU but we have little confidence this will work and we are at a painful 8 months with no washer.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

This washer does not distribute enough water to wash clothes properly. I continually take clothes out of washer that are not completely wet. My darker clothes have white spots of detergent on them that did not get rinsed off. This product should be pulled from the stores. We have tried everything, using deep water wash, bedding wash, to get more water in the machine. Our clothes are not coming out clean. Complete waste of our money!

We have had a Maytag dishwasher for just over a year. The control panel acts up randomly and has finally quit altogether. The design of the handle is very poor as it pulls the control panel away from the door. Will never buy a Maytag product again. This is a very clear design flaw and when we called Maytag they offered no help as we are passed the guarantee.

Bought a Maytag HE top load washing machine (Model MVWB765FW) in Jan of 2019. As I write this the repairman is banging away on the machine to replace the gearbox that had gone bad. This is the second time a repairman has been out to work on the machine. The first time was to replace a bad water pump, which was when the machine was about six months old. Maytag would have you believe that Power and Durability Come Standard. So too, apparently, are visits from the repairman. To its credit it does a good job cleaning clothes - when its working. If youre going to buy this machine, I recommend purchasing an extended warranty - youre going to need it.

I bought a French door refrigerator on May 23, 2012. It is now July 9, 2014 and the repairman has told me the compressor is bad. Maytag will do nothing about it because it is out of the 1 year warranty. I am very disappointed because I thought I was buying a quality appliance. I will never purchase another Maytag appliance!

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

We do not use the range daily. Our household consists of only two persons. First time we operated the self-cleaning feature on the oven the outer pane of the double glass pane door had what appeared to be grease stains and dirt. In as much as it is a SEALED double pane glass door there is no access to the outer pane to clean it. The double range was only 16 months old and was purchased at RC Willey in Henderson, NV. We also purchased ALL Maytag appliances for our kitchen i.e. refrigerator, dishwasher, microwave, washer and dryer on the same date. In addition we purchased furniture for the entire house at RC Willey. The Service Department at RC Willey advised me to access the Whirlpool website for assistance or to call an independent service repair contractor at my expense. THANKS MAYTAG! After having had your laundry appliances for over 30 years, without any service problems whatsoever, I was lulled in a false sense of security over the quality of your appliances. Now I have a household full of Maytag appliances and am at the mercy of independent service repair contractors.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

My Neptune washing machine does not drain or spin. It keeps going unbalanced. I am told that I used the wrong detergent. The machine takes a whole day to wash a small load of clothes and then never finishes. Clothes and towels are constantly being ripped and torn. This Maytag product is inferior and we have paid a lot of money for this product that does not work. Repairs to this product are not advised, we have been told that we just need to buy a new one again. This is poor service and poor advice.

On February 2006, I purchased a Maytag Quiet Series 300 Dishwasher and on July 2007, a motor leak. Maytag fixed it for free even though it was out of warranty. Thereafter (December 2008), the touch pad failed and I replaced it for $50. It is now August 2011, and that new touch pad is bad again, and this time, the part is $170. The Maytag will not run and the lighted display will not function from the start button. This was a $450 dishwasher that is now only five years old and useless.In all fairness to Maytag, their customer service is very good and willing to work with customers. Unfortunately, the product is very inferior in my opinion. To have stupid stuff like a control touch pad failing every three years is absurd and the replacement cost makes fixing it a bad investment.I will be going out this weekend and buying a brand-new inexpensive dishwasher that is on sale for $229. This model is not a Whirlpool product but it is a name brand.

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

My Maytag range from the 1990’s is the easiest to clean top of the range I have ever had. Controlling the temperature of cooking is very easy. The oven is not as responsive As it takes about 10 minutes to preheat. Once heated it maintains an even temperature.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

Purchase of what we thought was high quality Maytag dishwasher. Paid $600 and $250 to get it installed, which was really just to take out the old dishwasher we wish now we had kept, and plug in the new one. After 2 years, repairs needed to replace the control panel and key pad must be replaced, cost $340 plus labor. We will never buy Maytag again. Called their hotline, 800-877-6777. They cannot offer any help. Called the co. we bought it from, a Maytag dealer, Haleys Maytag of Antigonish, Nova Scotia. They too offered nothing except to sell us parts... control panel and key pad. Called lawyer who has class action suit now against Maytag, Eppsteiner & Florica. They are not representing customers who live in Canada, only U.S.My recommendation to Maytag dealer who only sells Maytags, Haleys Maytag of Antigonish, Nova Scotia, find another company to represent. Maytag is a real loser. Never again purchase a Maytag, and I told 10 people who will tell 10 people... who will tell 10 people. Our model number... same as all of yours... the loser MDB6709AWW1. Dont waste your money buying this overpriced dishwasher that will then require you to spend more money every 2 years on a Control panel and Key pad that are defective from the factory.

I am a regular customer of Leons and used to buy all my home appliances from them, because I trusted their quality and service of their products. However, last time I bought French Door Maytag refrigerator from them, about two years ago, we suffered from defects in this type of fridge. The problem started before one year when my wife saw some leakage of water on floor in the front side under the fridge freezer door. In the beginning, this was occurring once a month or every two weeks, so she didnt think it would be a problem or it might happen occasionally. However, the water leakage now became worse and almost every day. We had to put a towel permanently under the freezer door to dry the water which appeared ugly. Also, I had couple of accidents that my child slide over because of that water leakage. I spoke to one technician, he told me resolving this type of problems is not guaranteed because the problem will appear again or after while. He said this could be a manufacturing defects in this type of Maytag fridge models!!! Another problem appeared also one year ago, that one of the door handle started to shake very little, but now it looks like moving from its position and there is no way to fix it!!!Therefore, when I requested the help from Leons they told me that, You didnt buy the extended warranty and we cant do anything for you!!! You can talk directly to Maytag. Then, I send email to Maytag explaining the problem. They even didnt bother to reply or call me. Now, I feel that I was bluffed by these companies. I didnt think that I was buying a $2,000 refrigerator to scrap it after two years. That is ridiculous when you buy defected product from them, but they dont care to resolve the issue.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

We purchased a Maytag front load washer in May 2006 (MAH6700AWW). In November 2012 we had a leak and called a repair service. We were told it was the dispensing hose which had a hole worn in it and was replaced. In February 2014, we called the same service and was told that we had the same problem. Now in November 2014 we are experiencing the same problem. We have notified Whirlpool of this problem and each time were told that the machine was too old to reimburse us in any way. Guess who wont be buying any Whirlpool products if they do not back up their faulty workmanship.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

Would need 3rd panel for 8-year dishwasher - Either no lights come on the panel or Load done lights, like now. It has happened so many times over the years from about a year after spending a lot of money on a Quality unit. Many times I was able to operate it after turning the breaker off/on or leaving it to sit for a week or so, multiple times! Also, the rubber on the racks did not do so great - peeled and rusty. I did apply rubber repair multiple times, then got new racks at my expense. Several other brands bought over the years lasted 10+ years with no repairs!

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

We purchased a Maytag Dishwasher (model number mdb6759aws3) about 3 years ago. After about 1 year, the control panel started to go. Certain options would not light up. If I used the options that did light and shut the door, the dishwasher would work. I had called Maytag, and they were charging almost $200.00 to come out to repair. Now after 3 years, the entire panel is out. We had someone come out. We ordered a new touch pad for $265, and it still did not work. It is the control panel that is dead. What bothers me is that after reading online, this seems to be a continual problem, and Maytag does nothing to help the consumer.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

2 major repairs in 8 years, ridiculous! We purchased a washer and electric dryer pair in Feb. 2012, had a repair for the control board (CPU) 4+ years under extended warranty, had another in 2018 for the same thing. I was told power surges could cause it, however I have a WHOLE HOUSE SURGE SUPPRESSOR ON THE INCOMING 200 AMP SERVICE AND KNOW THATS NOT THE PROBLEM!!! Had the same CPU go out again in Nov. 2020 so, rather than pay $370 for the part plus labor, we bought a top loading GE with an extended warranty and factory 10 years on the motor. We will never buy another Maytag product again. We were told that we shouldnt expect to get more than 6-7 years from a washer now, ridiculous. Manufacturers are outsourcing electronic boards overseas to maximize profit and could care less about quality control!!! Junk!!!

I was all too excited to FINALLY own a new set! I conducted research and read reviews. We decided on the Maytag Bravo XL set (Lowes) and was thrilled! For the first 6 months. They were both fantastic! 6 months later, several times the clothes washed were soaking wet as if they had been set on soak. It continuously alerted to clean after 3 loads. The dryer... Well, evidently, if you live in a high-humidity region, DO NOT HOOK TO THE WATER LINE FOR THE STEAM OPTION. It will soak your dry clothes! After 3 loads of drying, it fails to re-start for the 4th load for at least 12 hours! When paying over $1,590 for a new set, this should not be an issue. Mind you, I do laundry once a week - 5 to 7 loads including linen. Fortunately, we paid an additional $200 for the warranty at Lowes.Lets see what happens there!

The best we can tell, we got our Maytag in 1991. This was because the repairman told us that was the last year they made parts for it. It ran wonderfully until 2018. The water valve broke, but a repairman easily fixed it. In 2019, it stopped running. The repairman fixed it, temporarily, he said. He refused to charge us for his work because he said we might get a few more loads done before it completely pooped out. Were still using it. I love this machine. It has gone WAY past the expected life span of a washing machine. Weve had it for 29 years!

I purchased a 2006 model Maytag Top load Washer and Dryer used 9 years ago January 2010 to replace a 2009 Samsung front load washer/dryer. I had to replace the agitator on Maytag washing machine before I could use it. Fast forward November 2018 the washing machine stopped agitating the clothes, but would spin the water out. I replaced 2 belts and thoroughly cleaned underneath and inside washer to remove soap residue. Maytag washing machine has been used twice a week since 2010-2019 and still going strong. Maytag dryer has never had any issues. I also own a set of 25+ year old Maytag Washer/Dryer both still working.

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

This is Maytag model: MVWB765FWO-Top loader. HE rated. It handles mixed loads without balance issues but I cannot yet address reliability. The new machine averages 7+ loads weekly and is in the 8th week of use. The overall performance is clearly superior to the Kenmore Elite it replaced.

This is undoubtedly the worst washer I have ever owned or used! I have never before felt compelled to write a review on a product, but I wanted to make other buyers aware. There is not enough water to clean the clothes - the water level doesnt even cover the top of the clothes, so the top of the clothes are dry as they are agitating! After drying (dryer doesnt dry either) the clothes do not smell fresh or clean. Ive put up with it for 3 years and am disgusted every time I use it. Im just about ready to buy another set.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

Well I have the washer and dryer. I love the dryer, it is excellent! Now on to the washer. It tries to save water so I guess people in California would love it. I have a laundry room in the basement and one up on the top floor with the Bravos in it. I only do the clothes that are not dirty but a little smelly in the Bravos. Any clothes that are dirty I do in my 20 year old machine in the basement. Do not purchase this machine if you are under 56 because you will need a step stool. Everything I wash I do on the longest cycle because the other cycles do not get all the clothes wet. Think about what I just said. The machine does not get all the clothes wet. Do not purchase this machine. I really cannot call it a washing machine, but they look real pretty in the laundry room.

I purchased a Maytag Bravos Quiet Series 400 in 2010 and it is now leaking like crazy and sounds like the bearings are going or gone in it. I researched washing machines for over a month before purchasing, and it seemed like this would be the machine for our active family. So much for research. It washes clothes okay, but is a bit rough on them. I found that it has ripped some of my more delicate items. When I contacted Maytag, they sent me an email with contact information to purchase a maintenance contract for $395 which would cover the machine for only 1 year. My husband is very mechanical and took the washer apart thinking the seal/gasket may have come off. He cleaned up the seal and the area around it, and put the seal back on. It did not help. He also noticed that the drive shaft to the motor was beginning to RUST! This machine is only 2 1/2 years old! So, if you are noticing that your whites are getting orange spots on them, this is probably happening to your washer, as well. Maytag should step up to the plate and recall this machine.

Just got off the phone with Whirlpool Customer Care after getting the run around between parts and customer service for most of the morning. My issue is with the shelving on my MSF25D2EAS01 Maytag side-by-side refrigerator. The plastic surrounding the glass shelving is disintegrating and they are not admitting to a defective design only that the original part has been obsoleted and a new one is available for purchase (an over $300 expense to replace three shelves) on a unit that is just over 2 years old. I am willing to bet the old part has been replaced with a different design after they realized a substantial number of customer complaints. As an engineer, it is obvious to me that these shelves are poorly designed for their intended purpose, furthermore my work allows me to recommend appliance brands for large projects so I see no reason to recommend Whirlpool or any of its subsidiary brands (Kitchen Aid, Maytag, Amana, Jenn-Air) to any of our clients. Whirlpool quality and customer service is substandard and no better than any imported brand of appliances.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

I bought a Maytag Bravos washer and dryer two years ago. A week after the one year warranty was up, my dryer broke. That was in October. It took me until February to get it fixed, but within two months it broke again. It has taken me until now to get it fixed again and they found the same problem; the thermal fuse blew. Both times it has cost me over $100 to get fixed, but I still cant use every part of the top panel; I can only use timed dry cycle. I’m expecting the dryer to go again. The repair man had to re-glue the seal that went around the drum. The vents were all clean and were blowing fine, so we’re not sure why this keeps happening. Our family have always owned Maytags and they have always lasted for 20+ years. I am so disappointed with Maytag at this point and will never buy another again. Go back to the old days, Maytag! By the way, has anyone noticed they dont run the Maytag commercials anymore, because I have!

I purchased a brand new MHWE450WW01 Washer and MGDE500VW2 Dryer in February. The dryer takes forever to dry something; seriously, 3 hours for jeans! The washer sounded more like a jet engine taking off. I called Brothers Main, they sent a service person who identified right away that it was a known problem and he had over 6 repairs already, but be prepared to wait up to 3 months for the replacement parts. This is ridiculous. The service center, you can never get through to them and when you do, they dont seem to care. I had a 10-year old washer that made less noise than this brand new one that I spent $1800 for.

I purchased a Maytag side-by-side, model MSD2656DEQ, in June 2000. First service call within a couple of months was for a very noisy ice dispenser, which the tech said was normal. Other than the noise, the dispenser has worked fine. Aug. 2005, the freezer frosted up and the tech replaced the defrost timer and defrost thermostat. May 2010, I had the same problem again and again these two parts were replaced. This morning, I found the food thawing in the freezer, 3 1/2 yrs since last repair. It is Sunday so will have to call tech tomorrow. Third repair in 13 years for a $1500 (2000 year dollars) Maytag. I have never had an appliance with so many problems and it was the most money I ever spent on an appliance. I am done buying Maytag products.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

We purchased the Maytag Bravos XL MCT washer and dryer in July of 2013 and have been completely and totally dissatisfied with every use since. We immediately contacted the store where we purchased them and were told we had to contact Maytag. We contacted Maytag on numerous occasions only to be read ridiculous solutions from a notebook that were no different than the instructions in the users manual and never worked. We had our first set of washer (with agitator) and dryer for 23 wonderful years. The washer absolutely does not work. The decision to remove the agitator and reduce the water levels is absurd. The soap does not get distributed, the lack of water causes loads of clothes or sheets to get rolled up into tight balls with no hope of being cleaned, and the spin cycle is so powerful it rips your clothes apart unnecessarily. The dryer is smaller than the washer and cannot handle the same size load the washer can put out and typically requires more than one cycle to complete a drying. All in all this has been the most painful experience we have ever had with any appliance. We are completely dissatisfied with both the store where we purchased these units and the complete and total lack of response from Maytag after requesting either of them to take back these units or make some equitable adjustment so we could purchase different units. We have reached a point where we will most likely store these Maytag units in the garage and purchase a new washer and dryer, being forced to accept the financial loss.