Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

Purchased washer last Nov. It broke over month ago, tub cracked and would no longer spin. The part took month to get. Same day was repaired. It broke again after 2nd load of wash with the same issue. I want a buy out or a different washer. It also tangled the clothes. Model no WET4027HW0 Purchased from Lowes which had good service.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

This is Maytag model: MVWB765FWO-Top loader. HE rated. It handles mixed loads without balance issues but I cannot yet address reliability. The new machine averages 7+ loads weekly and is in the 8th week of use. The overall performance is clearly superior to the Kenmore Elite it replaced.

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

Maytag Frenchdoor MFX2570AEM3 - Was initially really excited with this brand new fridge. We have not even fully paid it off, as we bought with credit at Home Depot, and it continuously leaks water from freezer! I have taken everything out, defrosted, spent about two hours pushing hot water through the freezer drain with a turkey baster and it was only about four days before I had a puddle on my floor again! We have bought quite a few maytag products before, but after this fridge, probably never again! If there is a recall or a lawsuit pending, please, someone advise me of either.

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

In December 2017 I bought a Maytag Bravos (w/o agitator) based solely on past experience (56 yrs.) of buying from Maytag without any complaints. A friend told me I wouldnt be happy with my purchase and she was RIGHT! It doesnt get my clothes clean to my satisfaction, my towels are all getting snags as well as silky sheets and pillowcases and dark clothes have a soap scum line on them. I have slightly better luck if I wash everything with the deep water level option but I still need to wash dark clothes a second time without any soap or fabric softener to lighten the scum line.I am very careful to use minimal amounts of high efficiency detergent but that doesnt help. I called Maytag and complained within the first month but then we were gone for the month of February and I just never followed up with them. Now Im sure its too late to do anything. I wish I had listened to my friend. Hopefully I can save another consumer from making the same mistake I made.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

Purchased a Maytag smooth-top range about a year and a half ago. Ive only cooked frozen pizzas in it. Have only had it on six or seven times. Havent used the top burners at all. Its an electric range, and I just had it hooked up a couple of months ago, as I was trying to find a place for it in the tiny kitchen. The folks who lived here before me, had a huge refrigerator and gas stove right next to each other, and I didnt want to go that route. Anyway, I went to put yet another frozen pizza in the oven, and the light doesnt work!So, after only six or seven uses, the oven light is busted! My mom had an old Westinghouse Terrace Top range, and it lasted well over 20 years with no problems. The only reason she sold it was because she remodeled her kitchen. It still worked great after all those years. Its after-hours now, but when I call Maytag tomorrow, Im expecting to get the run-around, if the other reviews are accurate, and Im SURE they are. Wont ever buy another Maytag product again.

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

We bought a Maytag Bravo model top washer recently and have no good things to say about it. The startup time is too long and clothes are coming out with lint all over them now. If the unit could be returned we would do it immediately but we cannot.

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

I wish I had read the reviews before selecting this Bravos XL washing machine. I bought these from Conns Appliance as they were on sale 750. Rounded figure... They were delivered today and the company was professional and set them up, I have spent the last 4 hours washing the same medium load of childrens clothes trying to get them clean. Ive even separated them into smaller loads and am now into the 5th hour of laundering this same load... Im returning them but its gonna cost me 15% restocking fee. If theres a class action please count me in. I thought because our Maytag Neptune lasted so long wed have a great outcome again with these, boy were we WRONG!

I bought a Maytag front load washing machine. We paid $1,100 for this machine. About a month ago, it was making a loud noise. I called them and they said were going to come out and fix it. However, our washing machine did not have a serial number. It had the model number/purchase date, etc, but no serial number. Our drier had it, but not our washing machine. All Appliances stated they could not help us until we had a serial number. We spent around 3 hours on the phone with Maytag, trying to get a serial number. Melinda informed us that we were out of luck, and that there was nothing they could do for us. She stated to call Nebraska Furniture Mart, to get the serial number. We did. NFM does not keep serial numbers. They keep model numbers, and purchase dates, but not the serial number. I called Maytag back, and spoke with Arthur. Within 10 minutes, he gave me a serial number to use. Interesting. In the meantime, I have been without a washing machine for 2 days. I have a load of wash in the machine, because now the wash machine has gotten so bad it is shorting the breaker, and not allowing electricity to the machine. This caused the front door to lock and shut down. Inside the washing machine is a load of clothes. All Appliances now has the serial number to order the parts. The parts were supposed to be here yesterday, Jan. 9th. Surprise, they are on back order until Jan. 13th. I called Maytag to see what they could do regarding me without a washing machine for over 5 days, which could turn into 2 weeks. They simply replied that it takes time to order parts, and there is nothing they can do and apologized. I asked what about me having to go to a laundromat and sit for hours, doing laundry. What about sending me out a loaner, to do laundry until you can get the parts. They again replied; there is nothing they can do.I also stated I spent $1,100 for this front load top of the line, Maytag washing machine, because of its name, and supposedly good quality. They again said there was nothing they could do. They did tell me that the washing tub, the part that we needed, was on back order until January 28th. This puts me at about a month without a washing machine. They stated they would try and locate the part, and have it sent out to my house, not the appliance company that is supposed to fix it, but my house, so that once I did receive it, I could call All Appliances, and set up the time/fixing of the machine. This has been pure hell! Maytag is a joke. I paid a good price for a supposedly good company/machine. They are doing nothing to expedite the parts. They are doing nothing to back their products. They are not even offering compensation for my inconvenience of having to go to a laundromat, or being without a washing machine for over a week, and potentially up to a month.I have been without a washing machine for over a week. I have had a load of laundry locked in the washing machine. I have had to drive to a laundromat to do laundry, which includes time and mileage. I have been informed that the parts are on back order, and now could be up to a month without a washing machine. Maytag is not offering any compensation, no loaner machine, no replacement. Instead, they are just saying, sorry, you have to wait for the parts. I would really like the VPs. and Presidents of Maytag to go without a washing machine for a week, or their families to go without a washing machine for a week, possibly a month, and see what they have to say about that company.

I bought a Maytag dishwasher on June 2008. This new Maytag dishwasher replaced an older Maytag dishwasher that caught fire and was recalled (I found this out after calling Maytag). The new dishwasher (Model: MDB 5601 AWB) also had a recalled part (heater coil) in February 2011. Two months ago, (the unit is now 3 years old), the control board started malfunctioning (certain cycles no longer work). I called Maytag today (Aug 24, 2011) but I was told by a Maytag representative that there was nothing that they could do. After reading so many complaints, I am ready to file a class action suit. It seems that this company continues to perpetrate fraud against an unsuspecting consumer for they knowingly continue to manufacture defective products.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

I have gone several years with wasted food at random times because my Maytag refrigerator decides to stop cooling whenever it feels like it. This is a continuing thing that started since the appliance was brand new and it has never been resolved. Maytag claims that they cant do anything about my refrigerator. They can do what they want to. From my experience, I feel like the issue is that they dont care to make it right. I am finally fed up with this refrigerator and I am buying a new one. I can guarantee that it will not be a Maytag.

I like the full width drawer for large items. Our Maytag refrigerator is 12 years old and just beginning to make noises and get too cold. The little plastic features for setting the temp and humidity on the produce doors were the first to break. Water is inside door which is not as convenient.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

Bought new washer and dryer from Home Depot. The worst washer and dryer I ever bought. Own 11 house all have washer and dryers. Bought Maytag on brand reputation. Washer does not rinse close at all. They come out full of lint and soap. It rips sheets up. Takes like 70-90 minutes to wash and close have to be washed over cause they dont rinse out. Dryer takes (2) runs to dry. Depot said they couldnt take them back. $300 Roper washer and dryer work much better than these units I paid like $1100.00 for. Maytag reputation is **. I have Amana front loads in another house that wash in 29 minutes and they come out perfect. Amana dryer works great also. DONT BUY MAYTAG ON THEIR ** REPUTATION AND CONSUMER SERVICE WONT DO ANYTHING!!! I would add the receipt but it just a waste of time.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

The Aqua lift cleaning system is a complete joke. Have had to replace oven light bulb 6 times in 11 months. Control panel is completely discolored. Expected far more from a Maytag product.

I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

I, too, have had a lousy experience with this washer – it does not correctly sense the amount of clothing in the load, and often fails to get everything wet. Once the cycle starts, it does not necessarily pull everything into the water. You must ball each item up around the center or have sleeves and legs of clothing end up very twisted. Clothing is often very wrinkled and I do not feel that enough water is used to achieve clean clothes. I did get a good response from Maytag, who sent a repairman free of charge after the one year warranty period. He was very gruff and condescending – implying that I am buying the wrong kind of clothing. He reset the washer which improved the water levels, but now it is back to its old tricks. Hate, hate, hate this washer. Now it is failing to start unless lid is slammed shut! May get a new one in a black Friday deal, but have to figure out how to ditch this one while retaining my integrity/honesty to buyer.

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

Purchased Maytag 3000 series washer and dryer in June 2009. Like many other reviews, the washer is making a terrible loud noise during the spin cycle. I contacted Maytag customer service and was told wait time is 10 minutes and opted for the call back option. Received a call back from an agent located in Tennessee, United States and he checked for recalls or projects and found nothing. Offered a technician call in my area for $112.00 for 30 minutes to diagnose the problem. I told him that if he checked on the reviews, he will see many regarding this problem and a bearing issue at a cost of up to $700.00. The Maytag repairman is not only lonely but out of business and Whirlpool bought them out. I would never again purchase Maytag or Whirlpool products. We are seniors and do not abuse our appliances and why do they not last at least 15 years. Talk about disposal washer machines, who can afford to purchase them every few years. The washer sounds like a jet going through our house when it is in the spin cycle.

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

Do not recommend any top loader. The washer dont wash at all. My clothes just sits there floating in the water on deep fill. I have some white with metallic like marks. Ive have soap left in my clothes. I watched one load of clothes. It had a neon shirt, the shirt stayed on top with the bubbles, it just floated along around in circles. The service was crap too. I called about the metallic markings. They said it was normal and should go away after 15 - 20 loads. I cant afford to replace my clothes.

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

Maytag Bravos Quiet Series 300 - My machine is 3 yrs old and started making a very loud noise on the spin cycle. My last Maytag lasted 18 yrs and all my appliances have always been Maytag. I believe it now when Im told that Maytag does not make good quality washers anymore.

Bought a Maytag Washer, in 2010 the Bravo. Good looking washer and dryer. I bought a 4 yr warranty for both. My washer has needed service every yr of the warranty, leaks and has stopped running. Now it is out of warranty and it is leaking again. Was just fixed a little over a year ago. I am now seeing a lot of rust around the top of the washer. It has just about covered the one port where you put the bleach in. The seam around the top in the crease is full of rust. My dryer is fine, bought them both at the same time. I have never seen this on a washer before. My mom has had her Maytag for yrs no problem. I bought these thinking they would last, boy was I wrong.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

In 2011 we purchased a complete appliance grouping at Home Depot by Maytag to include the dishwasher. For some reason we neglected to purchase an extended warranty on the dishwasher. Lo and behold in 2013 our control panel went bad and the cost to repair it was almost as much as purchasing a new dishwasher. Thinking this was a fluke we were dumb enough to purchase another Maytag from Home Depot due to the loyalty made in the USA. Well here we are 2015 not even a full two years later the control panel started acting funny a few days ago and yesterday just plain old QUIT. Fortunately we were wise enough to purchase an extended warranty plan on this dishwasher so tomorrow we will be calling the repairman. Unfortunately Maytag has never solved the problem that has been occurring for at least 5 years and continues to sell this product to unsuspecting schmucks like us who try to be true to the made in the USA slogan. Shame on Maytag!!! Our model number is MDB7749SBM. Buyers beware.

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

In August my GE refrigerator of 22 years bit the dust. Went to our local appliance center and purchased this unit for $2100. Have only had it a month and am so dissatisfied with the water dispenser, ice machine and doors, I want to return it. I cant wait for all the other things to go wrong with it. I dont know who the engineer was behind this but he needs to be fired. I really wish I had reviewed this refrigerator before purchasing it as I will never recommend Maytag again after reading all the bad reviews. The name Maytag used to mean something dependable and made well... Rant over.

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

I have written to Whirlpool about complaints with this range and was very dissatisfied with response. The following were complaints on above range: Range does not have a light on it as the past ranges had. It is very much needed. Grates on burner are to high, therefore it takes longer for items in pot to heat up. Type of steel used on range is very thin and tiny, in other words very poor quality. This is what has happened since Whirlpool bought out Maytag. Quality of Steel that Maytag used is no longer since Whirlpool took over their products. This is true of All their Appliances (Refrigerators, Washers, Dryers, and Ranges). All meaning appliances manufactured by Whirlpool.Manual knobs for turning on oven have been replaced by touch screens, these eventually wear out and are very costly to replace. If it works why change it. Drawers on bottom of range used to be larger, now they are narrow and smaller height wise. Residue on base of burner appears quite frequently and has to be cleaned even if no overspills occur. And why cant Whirlpool make quality merchandise as good as Maytag use to make. Regarding the physical appearance of Range it is very attractive in looks, however Looking good and functioning poorly with inadequate materials used in construction of Appliances outweighs benefits of looking good. My wife and I regret not returning this appliance within 90 days of purchase. In the future we will not purchase Whirlpool or any other appliances manufactured by them if that is possible. Kenmore, LG and perhaps other appliances parts are made by Whirlpool. I received a response from Jake **, Whirlpool Corporation, Executive Office. The Comment from Jake that did not impress me was this: While we regret you are dissatisfied with the current design of your Maytag Range, this is the model that you selected. His comment says too bad better luck next time. Letter was dated March 5, 2014 received on March 13th or 14th.I sent a handwritten letter to Mr. Jeff Fettig on March 12th which was written on March 11, 2014. No response to handwritten letter to Mr. Jeff M. Fettig. Verification that the Executive Office that my email to you Mr. Jeff Fettig Chairman and Chief Executive Officer Whirlpool Corporation was received on February 20, 2014 by Delores **, Corporate Office Staff. Supposedly Mr. Jeff Fettig.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

I purchased an expensive Maytag washer & dryer, top loading, energy efficient, only to find it now shreds all of my towels, robes, dress, undies etc. Maytag reply was to put things like undies, t-shirts, & dresses in bags to wash... What about towels? I had an expensive white Terry cloth robe from Neiman Marcus which is now shredded, Im showing it to everyone. Plus the dryer has an area above the front door that snags everything. I open the door & clothing is hanging there, caught on this area. Tell everyone not to buy Maytag, theyre rip-off. Ive lost more money on ruined clothes & linens than the trash washer & dryer are worth, but Im disabled, handicapped, 61 yr old who cant afford to buy another new washer!

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

Bought a Maytag refrigerator model #MFT2673BEW10 in 2013 for $2100, the ice maker has leaked for two years. Paid for service come out and look at it, ice maker is shot, three years old, and it is junk. Tried to get help from Maytag Customer Support, what a joke. I was hung up on 4 times, and never did get any type of help except your unit is out of warranty. Bought at the Maytag Store in Saginaw, Michigan. No help there either. DONT BUY MAYTAG!!! They are junk!!!!

Two years old, single person owned and will not operate - At 2:00 am, April 25th, 2012; I went to take a load of laundry out of the washer. It was still full of water and would not operate. I am a single person. I do not do load after load in two years. In fact, I was doing a weekly load of clothing, nothing large. I paid close to $1,000.00 for this unit. This sucks and why only one year warranty? Are you Maytag? A Youigo car would run better than this. And they are built cheap.

I bought a Maytag washer from Lowes and bought the extended warranty. The warranty expired but Maytag is not taking responsibility for the lemons that they sell. I have seen many reviews stating that the bearings went on the washer. This is what happened to me and it happened twice already. I spent 798.00 on this washer thinking it would last for more than 6 yrs. They offered me a warranty for 368.00 or to purchase another washer at a discount price. Of course I refused but I want everyone to be aware of Maytag Washers - not worth the money.

Never dies, never have had to have it serviced. House burned down is reason why it died. So I rebuilt, bought another one, then moved took it with me, then left it with my daughter and moved to Mexico. The dryer is still working to date and this all happened over 10 years ago. I sooo want another one. Best brand period. I only buy Maytag as they last. Unfortunately I do not have one now as they were unavailable in this country so bought something different. I was told the machine I have currently was as good as a maytag - they lied. I recently found out they have them now, so when I can afford one again, I will purchase one.

I agree with everyone else on here. I would give this Maytag Neptune washer less than 1 star if I could. I also purchased this washer 5 years ago when I bought a new house. According to their commercials, the Maytag repairman is bored because their products are so great. I believe it is because the cost to fix their merchandise when it breaks costs so much.I had a 5-year warranty on my purchase and this washer started making this awful noise but the company wouldnt repair it because it was not broken. However, here I am less than 5 months later, and the bearings are so bad, the tube is scraping and falling apart and leaving plastic pieces in my clothes. I have a 3 year old I dont need plastic pieces in my clothes. You know my husband just left me and I do not have the money to spend on the repair ($500-700) nor have the money to spend on a new washer. Thanks Maytag for your great and wonderful service!

My husband and I bought this refrigerator on 11/24/17 at Lowes for $2969.00 (excluding tax and white glove delivery). Never thought that not even after less than 2 years we would be having so many issues with this unit. The fridge part stopped cooling a couple of months ago and we were told by a technician that it was due to some coolant issue which of course our home warranty (Choice Home Warranty) wouldnt cover the repair. Well my husband fought them and we were able to have a second technician come and told us it was a sensor issue which he replaced. In the meantime I called Maytag to complain and they wouldnt even send someone to take a look. Anyway, the fridge worked after they replaced the sensor but unfortunately last week we started having the same issue. You would think for such a price you would get a decent unit, but big mistake there...now we have to find a way to replace it and we have little kids in the house. I also find out that Lowes doesnt even carry that brand anymore, perhaps because its defective. Maytag doesnt want to help us and Lowes cant do anything about it. So please STAY AWAY!!!! Should we be compensated, yes I believe so and so does anyone going through the same issue. Money doesnt grow on trees, stop deceiving your consumers Maytag!

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

Bought washer in 2010 from Sears. Told me the washer had a sensor to measure how much water it needs. Was told by service guy that was a blatant misrepresentation by the sales person. It only fills up with 8 of water. When I wash my white towels with normal dirt (dog paws), with HE detergent and bleach on various cycles, my towels come out tie-dyed with dirt. Totally dislike this machine.

I bought a Maytag Gas Range in January 2010. In January 2012, the wiring caught fire, and now, the oven is unusable. Maytag was not very helpful in our loss of money and product.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

French door always has freezer closing problems. Whenever the freezer is not closed tight, the bottom will form ice block, and freezer doesnt close. I have extended warranty but the repair people do not give quick appointment. I sick of this product.

Purchased the Maytag Bravos washer and dryer at Home Depot. Previously had a Maytag set that was 25 plus years old that still ran well but was rusting out due flooding. Figured Maytag had great products. Have had mine for 4 years now and had nothing but trouble. Paid countless service calls, mainly on washer, will work for a short while and then stop again. Cant put more than 4 towels, or 3 pairs of pants or basically anything or the codes start popping up. I am so angry that a product I paid a lot of money for is such a piece of crap. Maytag Company has been no help and I see with all the complaints on this site I am not the only one who feels this way. A class action suit would be great!

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

This washer came with the home we recently purchased. I used the machine and OMG the spin cycle is NOT quiet.. I posted a video of it on FB. A friend of mine who owns and operates an appliance center watched it.. messaged me back and said Do not call repair man as it is cheaper to buy a new machine... I knew this machine sounded like a piece of **.. I know I wont replace with the same machine.

MDB8959SBB. Purchased this Maytag dishwasher late December 2013 and had it professionally installed on January 4, 2014. Could have burned down the house this weekend! Smoke everywhere! Thank goodness it was running during the day and not night so that we were able to shut off the power. Lights in the kitchen were blinking and smoke pouring out of the dishwasher. The house still smells of smoke. So disappointing. Ive always been a proud owner of the Maytag products. Never again. Especially after reading the reviews. Interesting enough, THIS dishwasher was purchased because of a recall on the PREVIOUS Maytag dishwasher I had trouble with. They gave me a credit to use towards my next purchase. Ive learned my lesson.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

I bought a new washer and dryer from Clarks Appliance on North Monroe St.,Tallahassee, FL. I do not like the washer. It is a top loader and has a lock on the lid. The pause button is supposed to let you open and then is supposed to continue the wash. But it releases all the water and shuts down. I asked to return the washer because I have had it only three weeks. They wont take it back. So now I would like to trade or sell it.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

It washes extremely well. Its reliable. The wifey loves it and thats enough for me!!! I have had no major mechanical issues. Since 2012 we use it heavily and every other day. I would purchase same brand if need be but Im confident that would probably be in 2024.

I have done absolutely nothing to this dryer except keep the lint screen clean. Have had it for 15 years. Keeps on tickin. It is used daily. Sometimes 3-4 times a day. The outside looks rough. But who cares. I bought a new lg washer with great looks and had it just a year and 2 weeks. Had to spend another $200 on it. Still doesnt work right. Im Maytag all the way!!! It is a simple dryer. But it is a workhorse. It was a gift from my mother and have so much appreciated it. It has been an amazing piece of equipment. From now on I will only look for the maytag brand for whatever appliance I purchase.

Brand new Maytag dishwasher, model #MDB6709AWBO, installed after one year warranty because of extended time needed to complete kitchen. It just never worked. Repairman says control panel faulty. Sears wont help or replace. Sears’ service is extremely poor, over one hour on phone transferred over and over and then told too bad by a Supervisor. After checking this site, I realized Maytag suck. And what to do now that I paid $700++ for fancy dishwasher that doesnt work. By looking at other peoples complaint, it will break down over and over.

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

Same problems as everyone else. Water not soaking the clothes, questionable load capacity, shaky (we have engineers in the house so there is no way they did not look for floor evenness as the stores/Maytag will tell you that you may not have done, complete bs) etc. Its absolutely horrible that were all now stuck with such a terrible machine. I really wish I had read these reviews before (I googled the machine earlier but got generic stuff and didnt stumble upon these reviews until much later). Maytag should take responsibility on this as retail stores do not take back appliances unless they are defective. The Bravos is definitely a defective product from the get-go though.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

The way the outlet line and pump are set up, the Maytag Bravos does not remove all water from the bottom leaving about 2-3 inches. Even following the monthly cleaning and care has not stopped the inside of the tub from producing MOLD. When I contact Maytag there was nothing they could do about this problem. At this point my washer is only a few years old. I attempted to clean it myself but the drum would not break free. My options are, deal with the smell of mold and mildew, Pay Maytag $250 to come out and clean it (this would need to be done every 1-2 years) or buy a new washer. NOTE: I paid about $550 for this one. I have run a few clean cycles with bleach, but I think at this point the mold has embedded itself into the plastic tub.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

Purchased the Maytag Bravo Nov 2010 and had to replace it after just 5 years. In the five years we owned it, it required a new water pump and the stabilizers had to be repaired. Its motor burned up and I was not able to find a replacement. I was quoted $224 (parts only) for a replacement motor and 10 weeks delivery. My wife never liked the machine as it was not able to clean clothes that well. We did not find much difference in any of the settings. We tended to put very few clothes in each load in order to get them clean. We were dissatisfied that it did not have a soak cycle and the lid lock was particularly annoying.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

We have had 2 sets of Maytag washer & dryers. Our first set was a top load. When we bought the Neptune front load machines we gave the top load to our daughter and it still runs great after 14 years! Our front load W&D are 7 years old. We have a dog breeding business and when we have puppies the W&D pretty much run nonstop for 16 hours a day or longer. The blankets and towels come out like new every time!! The only complaint I have is the top of the front load machines seem to be plastic and scratched really easy. But the enamel on the top load still looks new! We plan on shopping for a new set this weekend passing these on to our daughter. We will buy ONLY Maytag for the rest of our lives!!

Nice refrigerator, but cheaply made. I paid 1800 with tax for my french door Maytag and expected higher durability. It operates well but one worries about breaking drawers made of such thin plastic.

This washing machine has been very reliable.No repairs needed yet. This machine has stood the test of time. We use it at least.. four times a week. Light and heavy loads. It fits in our washroom and budget. Just perfect. I would recommend this brand to everyone.

Purchased a Maytag refrigerator in July 2011. The compressor failed May of 2013. After many phone calls to Maytag they replaced the parts (compressor) - my cost for labor (aprox $300.00). 30 days later, the service company had to repair a leak and recharge the system. March of 2015 the compressor failed again. Have spoken to Maytag (case # **) - they will provide no help what so ever. I was told I should have purchased an extended warranty.

I purchased a Maytag French door refrigerator (model MF12569) two years ago. The bottom drawer freezer does not work well. Apparently, the inner tubing of the freezer clogs and it creates huge puddles of water. My floor got damaged and I keep calling Maytag and all I get is their apologies. I purchased an extra warranty which will expire on the third year. I am really disappointed with their product. I see why there are so many complaints filed and what makes matter worse is that they dont seem to acknowledge the problem. Apologies do not cut it. They need to do something to reestablish customer satisfaction.

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.