I just want to give an update on my frustration with Maytag dishwasher I wrote about on July 16. In the end, I found a DIY solution and fixed it. I wrote an instructables here: **. Not recommended if you dont feel comfortable repairing things. However, the diagnostic test at least can give you some clue whether its the control panel or control board is at fault before replacing both. Thanks.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

I went to Home Depot in Kennesaw, Ga to purchase new W&D combo. I had found what I wanted but when the sales went to complete my order, the units I selected werent available. She talked me into the Maytag Bravo, but I specifically stated I needed a large tub because I wash a lot of towels and sheets. Well this expensive piece of shhh, doesnt even get all the items wet. Ive had to lift the lift and physically flip items in tub, especially with towels and sheets. Also, the washer is loud, did I say loud, I mean freaking loud. The dryer is fine, but I bought combo for a reason... Pricetag $1200.00 with my discount. I waited a week for delivery, I am mad as hell. Whats point of having large tub, when you barely get enough water. Luckily I found out now, so I can have them pick this CRAP UP, Do not buy. Theyre cute looking, but washer does not get your clothes clean.

My Maytag washer is only three years old and the control panel completely went. Not only did it cost me the service call, they want $360 to replace the control panel. I called Maytag/Whirlpool to see if they would help with the cost of the part. I am 60 years old and the only one who uses the washing machine. It is not beat up. Maytag would not offer any solution at all and refused to even pay for any part of the control panel. They said it was really my tough luck for not having bought the extended warranty. When you spend so much for an appliance, you do not expect it to only last three years and you should not need an extended warranty. I am so disappointed and I will never buy a Maytag or anything from its parent company Whirlpool.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

The unit has an ice maker. On a regular basis, water would accumulate at the bottom of the freezer pan. When the bottom pan got filled up, water would run out on to my hardwood floor. I related the problem to the ice maker. Researching the problem, I learned that the ice maker has an adjustment for timing the on cycle for filling the ice tray. After several adjustments nothing changed. I ordered a water control valve and installed it. The problem persisted. I installed a water pressure regulator but the problem persisted. I installed a water filter, the problem persisted. I turned off the entire ice maker and the problem persisted. The problem wasnt the ice maker. The real problem was the defrost cycle of the evaporator. The drain for the water was plugged with ice. I made modifications to the design so I could monitor the drain hole in the back of the freezer. Will I purchase another Maytag… probably not?

Purchased washing machine, with insurance that was offered to me 9/17/10. May 2013, control panel went. June 2013, dial switch went. July 2014 washer motor drive & belt drive had to be replaced. August 2015 is broke again. Will never buy Maytag again.

Purchased what was supposed to be a good dishwasher. In less than 3 years the control panel went out. It would cost more to replace the panel than to buy a new dishwasher. I will never buy another Maytag product.

Bought a Maytag refrigerator model #MFT2673BEW10 in 2013 for $2100, the ice maker has leaked for two years. Paid for service come out and look at it, ice maker is shot, three years old, and it is junk. Tried to get help from Maytag Customer Support, what a joke. I was hung up on 4 times, and never did get any type of help except your unit is out of warranty. Bought at the Maytag Store in Saginaw, Michigan. No help there either. DONT BUY MAYTAG!!! They are junk!!!!

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

We purchased this product from Lowe’s in 2009. We liked it for the first 6 months. Then it started putting holes in our clothes, the washer smells bad, coins get stuck, and make noise. Something needs to be done because there are thousands of upset consumers out there, all with the same complaints and Maytag does nothing. It’s not Lowe’s fault. They didnt make the washer. Read all of the complaints here.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

We purchased a high end Maytag Dishwasher from Lowes just 2 years ago. Within a year the machine was turning itself on, beeping for no reason, and eventually the functions on the control panel stopped working. When I called Lowes they gave me a number for a repairman who informed me that the cost of a new control panel would be $514 and its a known issue with moisture getting into the control panel. This is unacceptable. There are hundreds of complaints and a class action lawsuit regarding this issue and yet Maytag has done nothing to remedy this situation. I am forced to purchase a new dishwasher and I will never purchase another Maytag product.

I cannot control the water level which results in smelly and not very clean clothes. I follow all the manufacturers guidelines but after several washes, the smell comes back.

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

I bought this washer from Home Depot and was told I could load large comforters and even sleeping bags in it because there was no center agitator. There NEVER seems to be enough water to wash and rinse clothes completely. The water saver feature cannot be used as I have to use extra rinse cycle EVERY load to rinse soap out of clothes or I get white residue spots. I have MANY MANY shirts that have small tears in them I believe caused by this washer. I have monitored shirts I put in the washer and again today lost another high quality fabric T shirt. I have saved all of the shirts in hopes that one day there will be a definitive report that this washer design stresses clothes and damages them. I am going to purchase a new washer and it will not be a model like this.

Had side-by-side refrigerator for over 12 months - Went completely dead - Would need $500 work!!!!! Just got less 6 months. Now need filter for water and air filter!!!!!! I wish I can give it less than one star!!!!

In January 2006, we bought a Neptune washer and dryer, model# MAH5500BWW, because we thought they were superior to any other at the time. In January 2012, the washer started making a very loud noise in the spin cycle. It just kept getting louder and a technician was called in check out the problem. We were told that the bearing was going out and he found a hole in the back of the tub. He said it was not cost effective to replace the bearing and the tub and suggested that we continue to use it until we could no longer tolerate the noise. We are very unhappy with the durability of this washer, with the amount of money we paid to be going out only after 6 years of service. We have been a Maytag customer for 15 years and will never buy another Maytag appliance. We are going to replace the washer and dryer to keep a matching set and it certainly will not be a Maytag.

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

Maytag washer not draining properly. Called Aug 15 for help. First tech in on August 23, makes a diagnosis, orders part; no news, I call, am given Sep 15 as next date. Come 9/15, I take off from work, only to find out tech cannot come that day, to reschedule. Next tech comes 9/25 with a different diagnosis and different part to order. By October 3, an announcement that part came in, to make an appointment. By now, its been a month and a half, I am so angry. I call a friend, who fixes it in 15 minutes by simply clearing a clogged drain filter. This is unacceptable: the inordinate wait, incompetent techs, unresponsiveness from customer service. I cancelled my contract with Maytag Warranty/AIG.

I bought a Maytag washer expecting To get the best and have already had Service on it three times and it still isn’t working. I have spent a fortune at the Laundromat when I have a 4 month old washing machine at home and not getting anywhere with getting anything back on this. I am very disappointed in this Washing Machine.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

TRASH! Bad, Destructive, Dangerous. I am in awe of the worthless, destructiveness of this machine. This washing machine does not add enough water to even cover clothing. It agitates, tangles & tears clothing. You end up with dirty filthy tangled clothing. And this is after waiting for it to make some kind of idiot decision as to whether or not to wash your clothes at all. I frequently go out and it’s made a decision not to start at all. There also is no lint filter, so subsequent loads of laundry are dirtier than the first. You can’t wash clothes without enough water to cover them. I read online that it adds water depending on the weight of the clothing, so wet the clothing first to make it think it’s a heavier load. When you do that it spins the clothes first before it begins to wash them. Your clothes still come out of the machine dirty. If you’re looking for revenge, make someone a gift of this washing machine. Otherwise, put it out with the trash.

Bought a Maytag dishwasher 2011! Use it 2 weeks, digital board went down had it replaced! Now 2013, the board is down as well as the motor!! Can you imagine I use it once a day, at most 2 people in this house, and it completely breaks down! Thank goodness I have a Home Depot warranty. I would strongly advise against this product that I spent over $500 for 2 years ago!! How they could sell this dishwasher is a mystery.

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

Bought a Maytag French door refrigerator MFT2976AEM01 in August 2013. Started having problems before the refrigerator was a year old. I called to get it serviced and it took 4 months to get a repairman to check it out. He fixed one part and then ordered another part that he needed which took 3 months to get. After he replaced that part the refrigerator continued to have problems. The serviceman has been out to repair my unit 6 times so far. He has no confidence in the Service Engineers from Maytag. They recommended yet another part be replaced, however now Maytag will not cover the parts cost.They offered to let me buy a new fridge at a discount. After spending about $2700 in August 2013, I dont have the $ to spend again for a refrigerator. My refrigerator is so loud it has been waking me up for about a month now and I am sick and tired of it. Shame on Maytag for having such terrible customer service! I will never ever ever recommend a Maytag because this has been a nightmare!

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

In the process of self cleaning mode, oven died with door locked. Thermostat and thermal fuse went out, couldnt get oven door open or control the situation in any way except pray for no fire and wait for hours till oven cooled down. Door could not be opened, it died in lock mode. Called repairman, already in to 2 repair bills, still not operating. Called Whirlpool and Maytag, no help!! But amazingly they have created a new kit for the blower unit in this oven, model # Mew7527AW00. I paid a bunch of money for this oven, which replaced a 40 yr. old oven that had been in its place, operating fine, but it was Aqua Blue!! Its so sad that a huge Company as this will not help with an almost new Oven??

I bought the bravo 2 1/2 years ago. It started making loud banging noises during the cycle. I constantly had to rebalance my load. Then it stopped spinning at the end of the cycle or it would leave clothes wet. We had a repairman in and he told us that it would cost at least 600.00 for a new computer. Plus labor. Wow!!! I think a washing machine should last longer than that. Maytag should have a recall on this machine as I have read so many complaints about it.

First failed after 16 months. Second twice in 15 months. They are lucky to last 16-24 months. Stupid for a microwave that normally last 5 plus years for every other brand I ever bought.

I have called numerous times and the satisfaction is out the window. The MOLD is so bad on the gasket that I can not get it off and it just keeps getting worse. My clothes smell musty even after they are washed. Really fed up... I have had different Maytags for at least 40 years and I will not purchase another one at this point. Apparently your customer service is as bad as some of your machines. My word of mouth is not good advertising for you.

My Maytag dishwasher (MDB7749AWM) stopped working at only 15 months. I had a technician check it and he said its the control panel not responding after he opened the door panel. Its when I searched online for replacement part I learned about the defective control panel. So I decided to forgo repair and bought a new dishwasher. I feel the manufacturer should be held responsible and called the number found on the internet, 858-646-8500, about a class action lawsuit filed in California federal court. The lawyer handling the case called me back that day explaining to me its a long road before the case qualifies for class lawsuit. Because I live in Texas, he will need someone to represent Texas plaintiffs in order to include Texas in the national settlement down the road. I said, I dont expect anything but would like to see a class action. Since I have no use of the defective dishwasher, he asked if I am willing to send the machine to him at his expense. I said yes. For all of you complaining about the defective dishwasher, I suggest you to call the number to join the lawsuit. Even though we may not see a penny for long, long time, its the only way to punish the deceptive business.

I have been struggling with this machine for the last year. Just does not wash. I have tried power wash. Bulky sheets. Double rinse and nothing works. I bought this machine last year from Lowes and its my worst investment. When the load is finished the clothes are still dirty. Actually worst than when they went in. Read the entire booklet to no avail. Hate this machine

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

Purchased this machine (Maytag Bravo Washer) in May, 2015. Drive motor blew Jan, 2017. 18 mo. old. 10 year parts warranty and a tag on the machine that reads MCT (Maytag commercial Technology), which leads the consumer to believe this heavy duty machine. I called the warranty number, as I had properly registered the machine on the day of install. Said he would have a new drive motor out to me in 7 to 10 weeks. Yes. WEEKS. Really? I advised the operator that 3 parts stores in my area had the part available, and asked if there wasnt something we could do. He said no they are back ordered. How is it that Maytag cant get their own parts. I purchased the motor for 118.00 and my clothes are now washing again. NICE job Maytag. I suggest finding another company to buy your appliance from. Promises made are not promises kept. DO NOT PURCHASE THIS MACHINE.

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

I purchased a Maytag Bravos XL Commercial Washer on Jan.31, 2020. I have had problems with the control board twice in less than two years. To replace the control board it cost $560 plus dollars. I may as well get another washer. So, I have to buy two washers in less than two years, but the next one will not be a Maytag. I will not recommend their products.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

I spent over 2000 on a Maytag refrigerator. In less than 5 years, the coolant system has gone out twice! The only response I get is, “We are sorry, but it is 5 years old.” Are you kidding me? I have a 20-year-old fridge in the garage that is still working and I didnt spend over $2k on it! I thought Maytag was the best product out there and it certainly is not. Do not ever buy Maytag.

I purchased my Maytag side by side Model No. MSB27C2XAM00 in August of 2013. Within a 2 Weeks the lettering was gone on the control panel for the ice and water dispenser. I contacted Maytag and they replaced it, but the next one did the same thing, and the next one! They replaced it three times and they have all done the same thing. Now they are refusing to do anything more because they say I must be using cleaner or something on the panel because I am the only one having an issue with this! I assure you I have not used any cleaner and there are only three people in my household so it doesnt even experience excessive usage! I know this problem isnt as extreme as some, but when you pay this much money for an appliance you would like to think it should last longer than this!

After only about a year or so - and it is out of warranty - the clothes are not clean - there are white type of scum marks left on clothes and especially dark clothes. This is even after I use the recommended detergent and less than normal and do a double rinse. Have to wash clothes again with no detergent with a double rinse again. Just so annoying. Would never buy Maytag again.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

After the waranty ran out, oven failed to ignite. Called repairman who couldnt diagnose problem. Broiler works. Replaced some kind of wire & part for $350. Good for 6 months. Happening again. Paid a lot for this oven.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

I am in my 24th year of using my Maytag washer and dryer. The set was purchased in 1996, so it has been well worth the money. At this time, it does not spin out as well as it used to, but I just fluff the load and spin it again and then it is ready for the dryer. I have been very pleased with the set and have never had to have a repairman work on them. Cant ask for more than that!

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

We have had our washer and dryer almost 18 years and just recently spent less than $280 to get the washer going again. The dryer we haven’t had serviced yet. Great quality. So worth it. Our Maytag appliances are used frequently and keep giving out the best performance.

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

I purchased a washer on 8/13/12. I had it installed on 8/20/12. It did not clean clothes properly. I went to Two Guys and they said they dont take returns and told me to call Maytag. I called Maytag and they sent a a service agent to check the machine on 9/10/12. They said the machine codes were imbalanced and over stud. They need to recalibrate the machine. I did laundry the same day and still find clothes do not come clean. I need to return the machine. I called Maytag and was told they dont take returns. This machine is not cleaning clothes as it should be and I want a refund!

I bought my first centennial washer less than four years ago, warrantied that machine out. It was replaced by best buy because of the warranty that I purchased. We are a family of four, with that in mind the replacement machine was a model year newer and it last just over a year and quit. I bought the machine anticipating that it will last me the next 10 years. With two children at home now that is not working, all I have to do on replace a new machine. The repair shop has told me that they get more of the Maytag centennial machines and then any other washing machine is going to cost me more to repair it than to buy a new machine because I had faith in the Maytag products for many many years. This particular machines are extremely hard to diagnose as to what causes the problem or what the problem is and could take a long time to get it fixed as well as the expense of getting it fixed. I would not recommend another Maytag product nor will Maytag ever get any more money from us. This particular product has become a piece of junk that I cant even get rid of to recycling. Maytag has become a joke and this machine has become a 500 dollar hunk of junk in my opinion.

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

Five years ago made a major investment on new techno with this washer/dryer. This is an updated review. Since the beginning the washer causes awful water hammer. Tried using arrestors, they dont work. Clothes are stretched out. You need to bundle each piece of laundry! The wash takes forever. Top loader has lid lock, very inconvenient - Dryer is OK but needs extra drying time. Would not buy this washer...

Oven worked ok for a year and went under right day after warranty expired. I called factory-approved repair people in Brooklyn but was told repair would cost more than buy new oven. I contacted factory but got no help either.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

I installed a new Maytag Wall Oven Microwave Combo 18 months ago. I had not used the microwave in over a week. Last night, we heard a loud pop and realized the beauty glass front on the microwave had shattered. No one had closed the door too hard, in fact, we had not used it. I see where others have had this problem.

As with everyone else here I have had my second control panel go here. In the five years I have owned it the first was covered by an extended warranty that I had purchased when I bought it, the tough part is I was forced to buy another Maytag at a higher price because of a recall for dishwashers catching on fire. I found out about this by accident.

My Maytag Neptune washer also has a problem with mold build-up and now the door lock assembly is totally gone. I was unaware of the class action suit or I would have joined. I am just disappointed!

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

Washer breaks after 2 years. I purchased a Maytag Bravos XL washer from Lowes just 2 years ago. One of the main driving factors for the purchase was the Maytag brand. The repair tech just told us the bearing was bad and we need to replace this and the drum. The service call was $100 and the repair will be over $500. I can purchase a new washer for this. I strongly recommend not buying any Maytag product. The brand used to stand for quality but not now. I dont think the Maytag repair is still the lonely tech they used to be.

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

Purchased standard Maytag refrigerator w/ freezer on top in 2012. Freezer has never been able to keep ice cream. Never called for repair because after reading several of these complaints, mine seemed to be a minor frustration. However, I am waiting for the other shoe to drop.

I had my dishwasher for several years. Never had an issue with it. Cleans well and is very quiet which is exactly what I needed. A quiet and effective dishwasher is hard to find. The price was about six hundred dollars. I pursuit at Lowe’s. It was on sale along with a military discount.

I purchased Maytag dishwasher Model #MDB7749SBW in November of 2013. The front touch panel no longer works. Everytime I push the selection for wash it automatically jumps to Cancel. This dishwasher is less than 2 years old. I didnt purchase the extended warranty simply because I thought I was purchasing a very reliable product. Lonely Maytag Repairman of old. Ha Ha. I am very disappointed and am telling friends about this and all of the reviews Ive read that are similar complaints. I would never purchase a Maytag product again.

We purchased a MAYTAG refrigerator when we recently built our present home. This refrigerator has been a nightmare! Ice forms in the bottom freezer and then constantly melts out of the bottom of the appliance all over the floor. Weve had a number of service calls with no real effect. The computerized function that sets functions do not work well and often shut down the appliance with little clear way to start it up again. The ice maker/dispenser often clogs up or will not produce ice. Weve had it! We broke down today and spent the money on a new GE refrigerator. My very strong advice is DONT BUY A MAYTAG refrigerator with the freezer on the bottom!

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

After owning Maytag Model MHWE450WW01 for nine months, we had to have the bearing and drum replaced. It was down two weeks, and I missed two half days of work. Two weeks after being supposedly fixed, it is down again, belt out this time and I will be missing two half days of work again.After missing two days of work, I still have a piece of junk washing machine.

I am extremely disappointed with Maytag and the representatives I spoke with this evening. One laughed after I told her I was 7 months pregnant and without a fridge for a week after owning it less than a year. I was repeatedly and curtly told, We dont cover that, when I asked only to replace the recent food I had purchased. After having to request a manager several times, I was put on the phone with Dana ID ** who said she would not be able to help with any food despite the delay of a week for repairs to our fridge. However, she could extend our warranty for 6 months.The only reason we were able to get someone out as early as we did was because we knew a licensed Maytag service repair company. Otherwise, we would still be waiting for someone to come out to tell us it would be another week before repairs. The originally assigned service repair company by Maytag did not return our call. There was no concern or empathy from the Maytag representatives that I was pregnant and could have eaten food that was not cooled to prevent bacteria growth that would harm me and my baby.Even their service repair technician recommended to contact them about the spoiled food since it was impossible for the repairs to be completed before the end of the week. We will never purchase Maytag again. The appliance failed with no warning in less than a year, and the representatives made no effort to resolve our issue of being without food for a week.

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

Purchased new washer mid-February from Maytag dealer. He said machine has few problems and it was a good machine. 3 and one half months later, the machine is dead. No lights on display but power at plug. Repairman comes at appointed time and says it needs a new circuit board. Within a week, the part arrives and an appointment is made to install the new board and still have the same problem. Have to order a new console panel. 3 and a half weeks later, the part comes in. I have a job which I used the money to buy this machine and now the service advisor wants me to take off work so they can try to fix this machine. He told me I cannot return the machine. Whirlpool Canada LP Customer Assistance said they could not do anything. When I asked to talk to her boss, she put me on hold. She came back and said they would give me 6 months extended factory warranty and she would email this which I have not received. Work schedules will dictate when the next appointment will be made.

Never dies, never have had to have it serviced. House burned down is reason why it died. So I rebuilt, bought another one, then moved took it with me, then left it with my daughter and moved to Mexico. The dryer is still working to date and this all happened over 10 years ago. I sooo want another one. Best brand period. I only buy Maytag as they last. Unfortunately I do not have one now as they were unavailable in this country so bought something different. I was told the machine I have currently was as good as a maytag - they lied. I recently found out they have them now, so when I can afford one again, I will purchase one.

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

We bought a maytag dishwasher three years ago. Approximately nine moths later the control panel went bad. They came and replaced it. Approximately six months later they came again and replaced it. Approximately a few months later it went bad again. I complained to Home Depot and they replaced the dishwasher. Too bad they would not change the brand. Guess what? Here we sit, not quite two years later and again the control panel went bad just past the warranty. The cost to repair almost $470.00. Paid $525.00 for the dishwasher in the first place. I regret ever leaving whirlpool. Our first very heavily used dishwasher (whirlpool) lasted 11 years no problems.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

We purchased a front loading Maytag washer in January of 2011. We purchased an extended service plan in January of this year. I noticed a very loud noise and inappropriate operation during the spin cycle. I called the service plan, who contacted a repair service to come out and check my machine. I was told that there was a major problem that would be very expensive to fix and that the Assurant company would contact me in a few days. The company called and said that they would give me 75% of the value of the machine ($650) because fixing it was not economically feasible. I said that I did not want the money; I wanted the repair that I was guaranteed by my service contract. They referred me to the small print on the back of the sales letter. When I asked about any manufacturers warranty from Maytag (the washer was less than 2 years old), I was told that they had nothing to do with the manufacturer and I had to take that up with them. When I tried to call Maytag, they were decidedly unhelpful and referred me back to Assurant.There are several issues related to this event that I wish to complain about: 1) How dare a major company sell a thousand-dollar appliance that becomes unrepairable in less than 2 years and take no responsibility for the breakdown? There was obviously a defect in the machine that took over a year to show up (we are a household of 2 adults and did not overuse the machine). 2) How could a service contract issued under the Maytag name not be aware of parts covered by the manufacturer? 3) Should not the buyer of a service contract bearing the Maytag name be informed that it is not Maytag (the manufacturer) that is guaranteeing the product, but a third party?4) Should not the seller of a service contract be required to display the terms of the contract in a prominent place? The sales letter specifically states Repair or replace - If we cant repair your appliance due to a mechanical or or electrical breakdown, well replace it. The limits of coverage are in fact given in small print at the back of the letter and are on the contract, but this contradicts what is displayed prominently on the promotion letter. This is false advertising and should not be tolerated.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

I moved into this house and the dishwasher came with it. For an appliance that is over 8 years old it works beautifully. It cleans my dishes well and doesnt leave residue on them. I ran it through a cleaning cycle recently and that has only improved its performance. I recommend dishwashers by Maytag because they last and perform well.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

I bought my Maytag washer and dryer in Monroe County in Georgia, USA in 1980. Its a 1979 product and it STILL works perfectly fine after 40 years! Im 64 years old now and Im hoping Ill never have to buy a new set although I would love one because theyre so pretty these days.

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

I bought the Centennial top load washer and the dryer in May 2016 at Lowes. They are junk. I had a secondhand Craigslist Maytag washer that lasted 7 yrs and it was still running just fine when I got rid of it after purchasing this HE junk. The flimsy plastic door handle on the dryer fell off about 6 months ago. The clerk at Lowes assured me that the washer was high capacity & could handle heavy loads. Now I cant wash heavy loads because the agitator is already loose and getting ready to break. I have to wash smaller loads on the hand wash cycle. I cant wash my comforter or my rugs. The real kicker is I cant reach Maytag! I have tried calling to sit on hold for 30 mins to an hour. I tried the live chat during their regular business hours and it was not open. I am so disappointed in these machines. This is the first time I have ever purchased a new washer and dryer and this is what I get. I might as well have set $850 on fire. DO NOT BUY NEW MAYTAG MACHINES. THEY ARE JUNK.

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

I bought a Maytag Neptune top load washer in 2002. It worked fine (with the exception of smelly clothes) until October 2011. Since then I tried replacing two new clutch assemblies, a new outer tub and bearings. What we were just told this week: it needs a new spinner. Finally throwing in the towel and taking the $500 credit from Sears and buying a new washer. And I can guarantee I will never buy another Maytag product again!

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

We purchased a Maytag dishwasher mdb7749sbm1 in 2014 and have had nothing but problems with it since it was delivered. Within a year of owning it, the top jet fell off. We had it replaced and the repairman warned us that it would probably come off again due to a faulty latching system. In the last six months one of the brackets that holds the upper shelf has broken off and the dishwasher leaks every time we use it.My last cycle leaked so bad that essentially it completely soaked the extra large bath towel we place in front of it and travelled halfway through my kitchen. Not to mention that it never washed dishes well, regardless of what cycle we use, which/how little or much detergent/rinse agent and it does not filter at all, as theres debris all over my dishes and glasses. I am now looking to replace it before like other reviewers a control panel fire occurs. Strongly recommend staying away from this brand.

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

I purchased the washer and dryer approx 6 or 7 years ago. Out of the gate about a year the pump had to be replaced on the washer- 2010. 1/2012 the tub needed to be replaced, 6/2012 the PUMP needed to be replaced again! Then 2013 the dryer need a new board at the tune of $391.00. And today, yes - yet once again I need a new pump! Over $2,000 in repairs on these awful machines. I called Maytag because I thought maybe they would care - not so much. The rep told me that the Bravos models were discontinued (shocker) but that she could give me a discount on a new comparable version at ONLY $600. How nice! I will use these until they fail again - which according to history - that wont take long and then I will NEVER EVER EVER purchase a Maytag product again. We work hard for our money and continually giving it to a company (for parts) for a product that they failed to make a quality product is not going to happen again! DO NOT BUY MAYTAG. Do your research and give your money to companies that care. MAYTAG should be held accountable and a class action suit should be filed. They need to GET IT and they never will if we sit back and let them take advantage of consumers.

We loved the Maytag dishwasher when we first bought it. After about 5 years it started leaking. Had rubber gasket replace, only held up 2 years. This was the only problem.

13 months after installing the dishwasher, the touch pad no longer functioned. Called Maytag 800 number and they said out of warranty. I sent out repair man and he gave me a price for repair totaling approx. $300. Called back to Maytag and asked for a supervisor, she agreed to send the parts for free and I had the repair man install. Out the $120 for the repair and wonder how long it will last this time! I will consider a buying an extended warranty? Next time I will buy a lesser priced dishwasher with a dial, no more touch pads.

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.