I purchased a Maytag MDB7749AWM model dishwasher in March of 2012 for approximately $600. Fifteen months later, the control panel has gone out on it. From what I understand, this problem happens so often that its not even worth repairing this dishwasher.

Bought Maytag Electronic Washer and Dryer on Feb. 7th 2020. On July 10th control board went out in dryer. 3 weeks without a dryer and hanging clothes in 112-118 degree weather in Arizona. I am 77 years old and too old for this. Dont buy Maytag!!. Had Whirlpool Washer and Dryer for 22 years. Never a problem, regret buying a Maytag.

The washing machine is great as long as you’re washing small loads. If you try to wash a large load or heavily soiled items it does not get them fully clean. I have had absolutely no problems with the dryer except that I have had to replace the handle on the door which was a very inexpensive repair.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

There are few nightmares that worm their way into reality, but the forcing upon us of the low water washing machine has excelled beyond mans wildest imagination. A tool which everyone finds an absolute necessity is now a tool which does not work! In reference to this particular machine, there isnt enough water to wet the clothes, it beats the garments with such viciousness, even on hand wash, pieces go missing off the clothes, ripped into oblivion. You no longer can buy a machine which does not SENSE the water level, so we have all been reduced to either buying new clothes every week, or wearing crumpled wrinkled disasters which arent quite clean, and we get to use 3x the electricity and waste 3x more water, not to mention wasted time in repeating the process in hopes of getting our clothes clean and wearable.

My washer is 3 years old, it sounds as though an earthquake is rocking my laundry room during the addition of water, rinse, and spin cycles. Cleanliness only when washed twice, along with the washer stopping at 12 minutes because of UL signal (unbalanced) - this happens even when I have a small load. The dryer does dry clothes however along with tons of Lint stuck to my clothes. I empty the lint screen after EVERY dry cycle. Have had repairman who charged me $70.00 and said he could not fix the washer.

I moved into this house and the dishwasher came with it. For an appliance that is over 8 years old it works beautifully. It cleans my dishes well and doesnt leave residue on them. I ran it through a cleaning cycle recently and that has only improved its performance. I recommend dishwashers by Maytag because they last and perform well.

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

I bought a (Maytag brand) Whirlpool washer but it didnt clean clothes, so I had a repairman out. He ran it through their test and agreed that my clothes had lint, pet hair, and dirt on them, and said that was as good as it was going to get. No one called back from Whirlpool. I called them and a second repairman came out, but it was the same story. I got the same repairman back out again after several calls to Whirlpool and listened while he called in and answered questions from Whirlpool - Is she using HE laundry soap, etc. - the same things they asked me. I bought the machine because it was supposed to have one of the largest capacities available. I stood there while the repairman told them that the clothes hanging to dry were covered in lint, dirty, and extremely wrinkled because they twist into a big knot in the machine, among others. No one called back again, so I called them. The service representative told me that I was loading the machine wrong, I was not using the right soap, and that the report they got from the repairman stated that the machine was working as intended. I told them that I was standing there as the repairman told them that my laundry was not clean. They told me that it was not what their record stated. I thought washing machines were supposed to get laundry clean and get the smell of body odor out. They suggested that I use the bulky setting, so I asked them if I should have to use the bulky setting for a load of underwear. They said that the machine was working as intended, but I wanted to have someone else come back out. The appointment was scheduled, but then the repair company called me and asked if I was aware that I would have to pay for the service call. I explained that there must be some kind of mistake because it was a new machine. She told me that Whirlpool had been doing this for a while and they werent sending out repair techs anymore without notifying the customer, and that Whirlpool has been doing it as standard practice for some time now. I requested a written statement from Whirlpool about the incidents but I was refused.

I have a MGDB850WR0 Maytag Dryer. I have had to replace the thermo sensor/heat sensor three times in the past three years. Dryer takes forever to dry. I spoke to the repairman who told me in confidence that his company receives a lot of calls about this specific dryer for the same reason. He said the part was originally made faulty and thats why it keeps going out. The part being the thermo sensor/heat sensor.

I had a 1 1/2 yr old front load washer. I was worried the filter might have a lot of dog hair in it so I called to just have it looked out. I couldnt remember if I had an extended warranty. Thought it would be listed with Maytag. They said no. I said OK. They recommended A+ to come out and said it would be $60.00. That was OK because I wanted to prevent any problems with the washer in the future. I thought them checking it would be a preventative measure. The tech came out opened it up said there wasnt much hair or any other problems. Put it back together, plugged it in. There was a Big popping noise and smoke! Washer no longer worked. The man said doesnt make sense but he would fix it and not charge me for parts etc. I called Maytag. They refused to do anything since it was out of warranty even though they recommended this company and there was absolutely nothing wrong with it in the beginning.After about 2 months he still couldnt fix it. About this time I found papers for a warranty with the Home Depot. The repairman said he works with Home Depot as well. Told me to contact them but I needed to pay $120.00 to him and file a claim and then he would fix it. Apparently he does not do service work for Home Depot. They sent out other repairmen. They tried to fix it but apparently it was deemed unserviceable he blew the mother board. Home Depot said they would replace or reimburse me the amount I paid for washer. Then a machine called said they were sending me a check. We will probably never buy another Maytag! Even though I want to buy American if they wont help or stand behind their products. I now have an LG we bought from Pacific Sales with a cheaper warranty and much better customer service.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

My dishwasher, purchased in 2013 sings the same tune as many of these complaints...stopped working correctly, turned on whenever it wanted to, etc. Thought it was the cpu...no. Called Whirlpool and they gave me the same runaround that they give everyone...more money for a temporary fix. Did some more research that led me here and discovered that the ribbon cable leading to the control panel was fried due to heat and moisture. Easy to check for yourself... looks like brown crap on the cable...if you have a meter, you can easily check it. Tried to repair it, very difficult, but I tried. NEWS?...I wrote a complaint to the Better Business B... and mentioned that this is a safety issue, which it is.Believe it or not, just received a call from the corporate office (Whirlpool) and they were interested...I actually got their attention. They said they would have someone contact me... she did today... so this is encouraging. I dont know what they are offering, but this poor design is a serious problem, and if you want to get in Whirlpools face better go through the BBB. I already have purchased a new part and am adding silicone to the cable to protect it from the heat...but Im really seeking full reimbursement because this is not going to end well. Good luck...

Bad decision, Purchased in 2013 a Bravos by Maytag. After 3 years, it sounds like a jet engine taking off. The bearing is failing, sad as Maytag advertises to be the best. In 35 years, this is our 4th washer, actually the 1st was a hand-me-down that lasted longer. Unfortunately, we thought spending more and believing that Maytag would last longer was a mistake. Cost to repair is over half of the cost, so we have elected to run to fail. Then replace the Maytag that should have lasted at least 10 years. Warning. Purchase at your own risk. DO NOT buy this machine or any by Maytag, could be the same results. Or it could be that they are manufactured under Lowes specifications. From all the complaints the Maytag repair technicians are working, not setting around as they advertise. Only blaming myself for the purchase.

Please let me know if there is a class action suit. My lower freezer froze within a year, now 2 years later same problem. Im all in, this is clearly a design defect that we are all paying for. I would have bought something else. Ridiculous product.

Products spoiling even if set at recommended temperature. Hard to clean bottom freezer. Not happy with this configuration. Had to have repairmen in because of stopped up drain which I could not access to clean myself. Does not close completely at times.

Besides the fact that it barely agitates or turns over the clothes even on deep fill (which we need every time otherwise a whole HE cycle goes and the top clothes remain DRY), the oh-so-fancy power button stopped working at less than 2 yo! And guess what, because it is not a button or knob, but control panel sensor button you hover over to turn on, the fix is to replace the $400 little control panel box. On a $600 terrible washing machine! We trashed it and bought something else without a faulty button system. Very unhappy. Do not buy this.

Replaced an old Glenwood gas stove with this Consumer reports top rated Maytag. The boiler doesn’t work as well as we’d like, but after more than 20 years, no major issues. My wife & I both cook, & as with most things, I’m happier with it than she is.

Purchased a Maytag MBF2256HEW bottom freezer in 2005. About fours ago, I had to replace the control board to the tune of $140.00. Today the fridge quit working and this time it appears to be the compressor, so tomorrow we will be shopping for a new unit. It will not be a Maytag.

I am, was, a loyal Maytag owner. The Bravos design, center hub, catches the clothes and rips the material. Customer service will only state damaged material is not warrantied. So I now have a washer that in addition to washing clothes rips them.

Ive had a Maytag washer and dryer for 10 years. They have worked well, havent had any problems. I bought Maytag because of their excellent reliability, which has proven true. Design is not as modern as others, and doesnt have all the features, but overall solid reliable washer.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

I called. I was told nobody else ever had that problem. She hung up. I called again. The french door is nice to look at but it does not seal properly and there is CONSTANT build up of BLACK MOLD no matter how much cleaning. It returns. There is no other design for a seal either. There are several creases in the gaskets and there is mold in all of them no matter how deeply cleaned or sprayed. The seal is poorly constructed. DO NOT BUY THEIR FRENCH DOOR... Also their ice maker shoots ice all over the floor.

Purchased a Maytag four door refrigerator and it leaks water all over the floor. Every few days I remove ice from the bottom of the freezer.

I have not been satisfied with this Bravo washer since purchased 4 years ago. I have been holding back anger, hoping things would somehow improve. Clothes are never really cleaned, cant even fill washer with very many clothes because the washer goes off balance. It takes a lot longer to do laundry. Clothes spin so fast they are in knots when I put them in the dryer. I always have to iron clothes. Today, well today we have a leak coming from under the washer somewhere. So please tell me, what is the advantage to having a HE washer again? By the way, no warranty since its been 4 years. I will never buy another one.

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

I changed from another HE brand to this model. No comparison. This machine can do twice the work... but double the time. My former machine was quiet while this one is not. Maybe I got spoiled to the former brand, but Ive never heard so much noise from a washing machine! Ive always thought Maytag meant quality but I think they may have missed the boat here. I tried reviewing on their site but when I gave it two stars, I got an error message. Clever, Maytag.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

I had my kitchen remodeled less than 4 years ago with a Maytag refrigerator, Bosch dishwasher, and GE stove. I had a 1 year warranty, and purchased additional 2 years. The warranty ran out last year, and the refrigerator is not working. Maytag customer service said all they could offer was 1 year extended warranty for $300. I told them a refrigerator should last longer than 4 years. They agreed, but that is all they did. Ive read other online reviews, and it appears a lot of people are in the same situation (however my fridge is not on a recall list). I will never buy another Maytag product ever! My GE and Bosch appliances are working just fine.

Maytag washer Bravos MCT. Let me tell you your guidelines do not help at all. Would someone please tell me how to get my laundry clean when it doesnt even get all the clothes wet? Looks like Ill have to go to the laundromat at least I can get my clothes wet. You should be ashamed to put out such an inferior product. Worst washer ever.

Bravos XL washing machine is the worst washer I have ever used. IT DOESNT GET THE CLOTHES CLEAN! There is not enough water when filling up, and you cant control it. I put a load of dog blankets in the washer and at the end, they were in the same order as I put them in; they hadnt moved! All the stains were still there and there was soap scum everywhere. Also, while I appreciate a large drum, it is so large that I cant even reach down to get the clothes on the bottom, I have to use a stick to get them up. I am so irritated that I spent $1636 for the washer and dryer (dryer works fine but same trouble with the huge drum). I got mine from Sears online after checking the Consumer Reports which put it in the top 5 washers!!! Dont buy this washer. Waste of money. Will probably just have to throw it out and its brand new.

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

Dishwasher MAYTAG MDB7749SBM - Have the same problem as everyone else, panel board. Initially lights randomly blinked, flashed etc, but still washed dishes. Now it has completely died. Dishwasher is 3 years old.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

Purchased a pair washer/dryer Maytag Bravo XL module from Home Depot, Brentwood, CA #1076 branch. The first day I received my machines, the dryer had a defect. I called them within 24 hours to report the issue and requesting a return. Home Depot wont take it back; they said I have to go though the factory warranty to fix any problems. Its like buying a car, once you drive it off the lot its yours they said. 3 weeks after the washer started making noise. Home Depot kept delaying my claim for more than six month so I couldnt dispute the charges with the credit card company and avoid the California lemon law. I consider this a loss of money and time. Worst appliance purchase experience ever.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I have several rental properties and every Maytag dishwasher I have installed in the past three years does not work. It is crazy that a national class action lawsuit has not been filed. There would have to be a large sum of money in fees for the firm that takes the case on. I am not usually for class action lawsuits but this is a known problem that Maytag refuses to acknowledge.

Maytag Washer and Dryer XL Bravos - The worst machines ever. I have had many washers and dryers and every one of them were good enough to get my clothes clean and dry without wrinkles. This washer Maytag Bravos Washer and Dryerdoes not clean clothes no matter which setting it is on. The dryer does not dry the clothes without wrinkles if it dries them at all. They are only about 6 months old, I have followed the book on usage and it still doesnt help. If I could pick these up and put them at the curb I would. If Maytag would take them back I would return them. Buyer beware.Updated on 03/17/2018: Maytag wrote to me and wanted me to give them my contact information along with any other info regarding their appliances. Still havent heard from them, and I assume if I do it will be like all of the other replies, Sorry for your inconvenience yada, yada, yada. I did check online for Lemon laws for appliances and there are laws for the consumers to fight the companies. If and when they contact me I will be sure to mention this to them for what its worth. I think a class action suit might be the answer for all of us consumers. If banding together would help count me in!!!

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I purchased a Maytag Neptune Washer in 2006 for $665.00 from Sears. Three years later, the control board broke and I paid $400 to replace it. In 2011, the motor and motor board need replacing which will cost $410.00. We kept getting an LR code. So in 5 years, our repairs cost more than the original machine. Maytag can count on never getting my business again. Im only sorry that I purchased a Maytag dishwasher this Summer.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

I am extremely disappointed with Maytag and the representatives I spoke with this evening. One laughed after I told her I was 7 months pregnant and without a fridge for a week after owning it less than a year. I was repeatedly and curtly told, We dont cover that, when I asked only to replace the recent food I had purchased. After having to request a manager several times, I was put on the phone with Dana ID ** who said she would not be able to help with any food despite the delay of a week for repairs to our fridge. However, she could extend our warranty for 6 months.The only reason we were able to get someone out as early as we did was because we knew a licensed Maytag service repair company. Otherwise, we would still be waiting for someone to come out to tell us it would be another week before repairs. The originally assigned service repair company by Maytag did not return our call. There was no concern or empathy from the Maytag representatives that I was pregnant and could have eaten food that was not cooled to prevent bacteria growth that would harm me and my baby.Even their service repair technician recommended to contact them about the spoiled food since it was impossible for the repairs to be completed before the end of the week. We will never purchase Maytag again. The appliance failed with no warning in less than a year, and the representatives made no effort to resolve our issue of being without food for a week.

Its the worst experience I have ever had with any product. I grew up watching the Maytag man as a child and thinking that must be a top of the line product. Boy was I wrong. I went out six years ago when I purchased my new home and purchased for 1,550.00 a brand new refrigerator with side by side, and ice maker on the bottom, silver in color. It looked great, the quality was and is terrible. The freezer stopped freezing a couple of days after the first year was up. The Service department at Maytag is terrible, I called them for assistance and they were anything but helpful rude is a better word. Its been a nightmare! How could they ruin that good, or even great name of that product. Never will I buy a Maytag appliance again. I tell all of my friends as well. Oh yes so far as the leaking is concerned, my floor is damaged as well.

Had a problem with the control circuit board on my 6 year old refrigerator. Had it serviced and found that the problem was common, the main circuit board needed to be replaced. The service person advised me it wasnt currently available from his supplier. I call Maytag and they said it was back ordered from their parts source. When asked for an availability date, I was told the date was unknown? I started a search for the circuit board and found it was indeed a problem for many many other consumers who owned this model refrigerator. Lesson learned: Maytag is no longer a good brand to own.

My husband and I purchased this Maytag bravo washer in May 2014. It is not even three years old and the bearings went out. Call the repair man and it would cost over $300 to have it fixed. I paid a lot of money for this washer, expected it to last more than less than a little than three years and I think its terrible. Its loud, water was leaking all over the floor, its just a terrible terrible washer. Maytags reputation is not as good as it used to be. Model number mvwx5008wq and ser number. C41430792. If you are planning on buying a washer do not choose Maytag!

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

Two years ago I bought a matched set of Maytag Neptune washer and dryer. Although I bought really liked the front loading and large capacity, I bought them because they were Maytags. I remember my parents grumbling that they couldnt afford a decent washer or dryer like Maytag and had to settle for Kenmore or some other brand that they figured was inferior. I noticed that they struggled through 20-25 years of maintenance free use of their inferior appliances. So when I found a pair of Maytag, I thought I had finally arrived. I was 60 years old and I knew this would be the last washer and dryer I would ever have to buy.It is now 2 years later and we developed dryer problems. The repairman found the computer malfunctioning and suggested it would be cheaper to replace than to repair. We asked him to check the washer while he was here and his diagnosis was similar. The drum bearings were gone and probably too expensive to repair. The Maytags are now in some scrap yard and I now have an inferior washer and dryer and I am looking forward to many years of maintenance free struggles. I used to think that Maytag repairmen are the loneliest people because their machines were reliable. I now know that they are lonely because all of the Maytags are garbage and not worth fixing.

Maytag washer, model# mvwp575gw0, which is under warranty. This washer is less than one year old. Within the first couple months the transmission leaked oil and service tech had to replace the transmission. A few months later – another problem, clothes wet after spin cycle - tech told me the agitator base and/or couple parts need replaced. Quality control appears to have been lacking at the factory when this washer was made. This house has only one person presently. The washer was not abused.

I purchased a Maytag Microwave Oven MMV5208 WS 1 from Home Depot less than two years ago. Mine was actually manufactured in April 2013 according to the ID tag. A couple of months ago it started acting up because a switch when the door closes began to malfunction and you had to open and close the door several times to get the microwave started. Then all of a sudden when you set the timer and pushed the start button it would flash on and immediately shut off. This is extremely frustrating because I paid more than $400.00 and purchased it less than two years ago. I am disappointed because Maytag advertises its reliability and this microwave is anything but reliable.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

This washer is only two years old and does the wash for 2 people. The control board has broken down and the lid lock did too. Of course the warranty had just expired, so there is no help from the maker, Whirlpool. Save yourself a big loss and dont buy these brands. Mine is going to the dump where it belongs. Thats $500 down the drain. Do yourself a favor and get a Speed Queen.

We purchased the Bravos X set (Model Number: MEDX700XW0 and Model Number: MVWX700XW2) form Lowes in October 2012. When the items arrived and we used the dryer for the first time in the delicate setting, the machine kept cutting off! So, Lowes brought us a new one. At first it worked but then the delicate cycle on that machine ended up not working as well a few months later. I ignored it and used the other settings. Yesterday, the washer broke. The entire basket detached! We were washing a small blanket and sheet set and kept hearing a loud banging sound. I went to check and the clothes were soaked and the entire drum was detached. I am so friggin angry! We spent over 1200 for this set and less than 3 years later, the set is ruined. I am on the phone with Maytag now b/c they need to replace this set or give us an upgraded set. They know that this set had issues yet they decided to still market and sell it. I want to sue!

I purchased and installed a high end MAYTAG above the stove microwave. After 3 years of light use I hear an electric cracking sound and it dies. Of course no warranty coverage. Model MMV5208WB-1. I have to conclude MAYTAG builds junk and does not stand behind what they sell.

We purchased washer at Sears 6 years ago. Have had same issues for 5 or more years. Sears has been out to check it 6 to 7 times! They clean it out, tell me to use (expensive) Affresh tablets monthly, problem solved but it never is! When we run our washer and walk in laundry room it smells like a sewer. If we open lid its even worse. I use Norwex all naturally, biodegradable laundry detergent. There is nothing Ive done to create this smell. Its a manufactured problem that probably relates to ALL the other issues with this crappie washer that Maytag will do nothing about. I called Sears for 7th or 8th time, said they could send someone out AGAIN, I said thats a waste of my time and yours. They told me to call Maytag. They wont do anything (warranty is up). Of course there are NO ISSUES OR RECALLS on this washer and obviously there should be with not ONE good review! Im angry. You all should be too. We paid good $ for a product that used to have a good name and they are screwing us. I think we should ban together with a class action lawsuit. Please give me your thoughts. They know something isnt right and they shouldnt get away with this.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

I am replacing my second Maytag Bravos washing machine. My first had heavy use and I rationalized that the 5 year life span was due to the heavy use. The one that I am replacing now is only 3 years old and has only done laundry for one 67 year old woman. It suddenly needed two parts with a repair bill that was going to be over $600.00. I decided it was in my best interest to spend a couple hundred more and replace it. I will not be buy Maytag again. The appliance company that I have bought most of my appliances from recommends Speed Queen which ironically also has a full 10 year warranty on all parts and labor.

I bought this electric dryer Bravos (Model# MEDB850YW0) in Nov. 2011. Since I bought it, its giving me the same problem - it doesnt want to turn on. Today is the 6th time that I have been calling the customer service to fix it. Yesterday, it just got fixed; and today, its not working again for the same problem. I asked them if they can give me a new one, since its not even over 1 year. But they said they will not replace it because it cant be fixed. But it is so ridiculous, and its wasting my time. This is so unfair. I paid $800.00 for this machine.

I got no help whatsoever. I will never buy in Maytag again. My washer has had 3 problems in 1 year. They tell you that they will send someone out the next day but they dont come until 4-5 days later.

I, like SO many other people, am experiencing problems with a relatively new Maytag dishwasher. Mine is Model MDBH979SAB1. I have owned the dishwasher for 4 years but use it 6 months of the year and, because I live alone, maybe twice a week. In effect, it has the equivalent of less than a year of normal use. My problem is the same as countless other people. I can tell from how it behaves that it needs a new control board. I find little comfort in the fact that I one of several thousand people experiencing a problem with a newer Maytag appliance. What concerns me, after reading many negative reviews and seeing Maytags response, is that Maytag does not seem to care. We need to get the word out. We need a massive boycott of Maytag. We need to hit them where it hurts: in their bottom line. Since they seem to be content to continue to put out defective products, the only way to protect consumers is to put Maytag out of business.

It washes extremely well. Its reliable. The wifey loves it and thats enough for me!!! I have had no major mechanical issues. Since 2012 we use it heavily and every other day. I would purchase same brand if need be but Im confident that would probably be in 2024.

I would bought a Maytag Aqualift self clean oven. I just ran the clean cycle and it is just as dirty as it was before I ran the cycle. Absolutely nothing happened. Now I have the 2 cups of water at the bottom of my oven they said to put in prior to clean cycle, that I have to get in and clean out. This is absolutely unacceptable. I would like Maytag to get back to me asap and offer a solution. **.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

Bought a washer and dryer from Lowes in June of 2016. Have had service on the dryer 3X and washer 1X since. Two person household that uses product a couple times a week. Dryer drum stops rotating / temp control fails / buzzer doesnt work / motor freezes up / washer makes loud banging sound at the end of the cycle every time....sounds like someone is hitting it with a hammer....Today I want a local serviceman to replace the motor but Maytag insists that I have one of their reps come out next Tuesday to examine the product and then go from there. I have been on the phone for 45 minutes trying to get them to pay me $128 for the failed motor that I will send them for inspection. They will not cooperate. They are hiding behind some BS policy. I want to inform you all in case you are contemplating a Maytag purchase. I will not purchase nor will I recommend Maytag to anyone.

The machine runs and runs and runs and still the clothes come out dirty. Clothes are often not even wet all over. The Maytag HE water-saving washer is a terrible Hoax. The dryer also is faulty. It rolls the clothes into a big, undried ball of dirty clothes.

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

We purchased this set 6 months ago. The store we purchased it from is unwilling to help us. Maytag insists there is nothing wrong with the washing machine. The machine doesnt clean the clothes. After a wash cycle there is pet fur and lint all over the clothes, even after it comes out of the dryer. The clothes are all twisted in tight knots when the load is done. The washing Machine doesnt dispense enough water to wash. I have taken clothes out of the washer and the items are dry in spots, most times you can smell the mustiness of a dish towel after its been washed.I used the steam clean dryer to fresh in up the curtains and the panels came out different lengths. Not eager to try that feature again. This is our 2nd dryer set purchase, the last set was 10 yrs old. I couldnt find anyone willing to repair it. I was told they dont make machines like they used to and they are all designed to last 10 yrs and you’re lucky if it lasts 15 yrs. Yes, we contacted Maytag and yes, like the many other folks who have shared their stories we also got the run around. Sad to say we are going to do our research and will be looking for a new machine. Im going to shamefully donate the set to a charitable organization and use the receipt as a tax write off. IF you’re doing your research, DO NOT BUY A MAYTAG.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

Dont ever buy this washing machine. After warranty was up, the motherboard went. After that, the pump went. Now, the machine has been shaking and we have to realign the clothes in the washer on an average of 6 times before it completes the cycle. The banging is nerve-racking! Never again buying Maytag!

The control panel acts just like the other reviews on here. The cancel light stays on. If I close the door, the washer automatically starts up again. It is unusable and it costs too much to have it repaired. First and last Maytag product for me.

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

We purchased our Maytag dishwasher on 12-26-2013. It was installed in early Jan. We did not buy an additional warranty. We put our faith in the Maytag name. We had no problems with our dishwasher. It was smooth and quiet. The one year warranty ended in Jan. 2015. In March of 2015, our dishwasher control panel began to go crazy. A short while later our Maytag shut down completely. Every now and then the washer will come on by itself. We will try and cut it off. It cuts off when it is ready. We have got quotes on getting it fixed by Maytag. With installation and tax, our Maytag Dishwasher cost us $649.22. Our complaint is the same complaint of thousands of other customers - the control panel. Maytag should have a recall and fix this problem. Maytags remedy for this problem is to sell a warranty for each year that a family owns the dishwasher. That is not acceptable. Please consider a recall on this item. Our model is MDB7749SBW2. Our serial #F33406909. Thanks for your help.

Maytag Neptune Stacked Electric Washer & Dryer. Had to buy a motor for Washer but lasted 12 years before giving problems again; then couldnt find anyone that would service for cheaper than $100 for just coming to your house plus $75 an hour for labor. Thats HIGHER than my billable rate! Rip-off Service & parts charges. Found out it was easier & cheaper to troubleshoot ONLINE myself using FIXYA site and others. Expense for an appliance above what most run ~ 1500 for both units. Plus if it doesnt have or offer a 5-year warranty then something is wrong with the quality! Maytag Neptune Series MLE2000AYW 27 Inch Electric Laundry Center with 3.34 Cu. Ft. Washer Capacity, 4 Wash Cycles and 6.0 Cu. Ft. Dryer Capacity, 3 Dry Cycles: White. Worst part on this model was a WAX MOTOR that they used for the Washer to control the door being closed or open. Next worst DESIGN error was they didnt put a drain hole in the plastic rim seal for the Washer door, that area would build up mold & mildew if you didnt learn to keep Washer door open at all times AFTER a wash. We learned by removing the light bulb! Therefore it was easy for my crew to learn to leave the door open after washing. This model was Energy star certified and had a long life here 12 years. Unfortunately I think they build these things to only last 10 years; then you have to replace them. In years gone by... the 1970s Washing machines and dryers would last 20 years!!

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.