I have written to Whirlpool about complaints with this range and was very dissatisfied with response. The following were complaints on above range: Range does not have a light on it as the past ranges had. It is very much needed. Grates on burner are to high, therefore it takes longer for items in pot to heat up. Type of steel used on range is very thin and tiny, in other words very poor quality. This is what has happened since Whirlpool bought out Maytag. Quality of Steel that Maytag used is no longer since Whirlpool took over their products. This is true of All their Appliances (Refrigerators, Washers, Dryers, and Ranges). All meaning appliances manufactured by Whirlpool.Manual knobs for turning on oven have been replaced by touch screens, these eventually wear out and are very costly to replace. If it works why change it. Drawers on bottom of range used to be larger, now they are narrow and smaller height wise. Residue on base of burner appears quite frequently and has to be cleaned even if no overspills occur. And why cant Whirlpool make quality merchandise as good as Maytag use to make. Regarding the physical appearance of Range it is very attractive in looks, however Looking good and functioning poorly with inadequate materials used in construction of Appliances outweighs benefits of looking good. My wife and I regret not returning this appliance within 90 days of purchase. In the future we will not purchase Whirlpool or any other appliances manufactured by them if that is possible. Kenmore, LG and perhaps other appliances parts are made by Whirlpool. I received a response from Jake **, Whirlpool Corporation, Executive Office. The Comment from Jake that did not impress me was this: While we regret you are dissatisfied with the current design of your Maytag Range, this is the model that you selected. His comment says too bad better luck next time. Letter was dated March 5, 2014 received on March 13th or 14th.I sent a handwritten letter to Mr. Jeff Fettig on March 12th which was written on March 11, 2014. No response to handwritten letter to Mr. Jeff M. Fettig. Verification that the Executive Office that my email to you Mr. Jeff Fettig Chairman and Chief Executive Officer Whirlpool Corporation was received on February 20, 2014 by Delores **, Corporate Office Staff. Supposedly Mr. Jeff Fettig.

We have had a Maytag dishwasher for just over a year. The control panel acts up randomly and has finally quit altogether. The design of the handle is very poor as it pulls the control panel away from the door. Will never buy a Maytag product again. This is a very clear design flaw and when we called Maytag they offered no help as we are passed the guarantee.

I bought this stove thinking of the Maytag repair man commercial that was advertised on TV for washing machines. Apparently Maytag only knows how to make washing machines (I did not buy one of their washing machines after my experiments with their stove). From day one the oven door never closed right, the self cleaning oven device had to be replaced 3 times over the year after have a repairman tell me that they all fail. I stopped using the self cleaning feature. This stove has cost me so much in repairs. The cook top is very very hard to clean. It always looks dirty. All the plastic knobs have melted off because the oven door never closed right. And the knobs are crazy expensive to replace as is just about everything on this stove. The oven temperature can not be trusted never cooked at the temperature it was set at. I paid a lot of money for this stove 10 years ago. And I am finally able to replace it thanks to a Christmas present from my 3 children. I love to cook and this stove made it difficult. My advice is to look for a different company when buying a kitchen stove. This Maytag has been nothing but trouble for me.

Was a Maytag washer. First one lasted one year. Second one replacement one lasted for years. But the company’s warranty is replacing this one without too much hassle. When it runs it does a good job. It’s a big load. All in all a very good washer.

My dishwasher, purchased in 2013 sings the same tune as many of these complaints...stopped working correctly, turned on whenever it wanted to, etc. Thought it was the cpu...no. Called Whirlpool and they gave me the same runaround that they give everyone...more money for a temporary fix. Did some more research that led me here and discovered that the ribbon cable leading to the control panel was fried due to heat and moisture. Easy to check for yourself... looks like brown crap on the cable...if you have a meter, you can easily check it. Tried to repair it, very difficult, but I tried. NEWS?...I wrote a complaint to the Better Business B... and mentioned that this is a safety issue, which it is.Believe it or not, just received a call from the corporate office (Whirlpool) and they were interested...I actually got their attention. They said they would have someone contact me... she did today... so this is encouraging. I dont know what they are offering, but this poor design is a serious problem, and if you want to get in Whirlpools face better go through the BBB. I already have purchased a new part and am adding silicone to the cable to protect it from the heat...but Im really seeking full reimbursement because this is not going to end well. Good luck...

I purchased this relatively expensive range and could not have imagined how dissatisfied I would be. The Aqualift cleaning technology does not work. There is no way to clean the oven door. They stress not to use oven cleaner, but as the Aqualift system does nothing to clean the oven door, there is no choice but to use oven cleaner, which they say will ruin the oven coating. Also, the grates are very heavy and it is impractical to clean the range top. I wish I had researched further; this product is a MAJOR disappointment.

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

Maytag top load 300 series washer - This is the worst washer I have owned! It does not wash items- especially sheets - without getting totally tangled up and twisted! I wish I had my old one back that lasted 20+ years. I will NEVER buy another.

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

I would bought a Maytag Aqualift self clean oven. I just ran the clean cycle and it is just as dirty as it was before I ran the cycle. Absolutely nothing happened. Now I have the 2 cups of water at the bottom of my oven they said to put in prior to clean cycle, that I have to get in and clean out. This is absolutely unacceptable. I would like Maytag to get back to me asap and offer a solution. **.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

Purchased the Maytag Aqualift self-cleaning oven and this feature doesnt work at all. I would have never have made this purchase if I knew the oven would not self clean. This technology with the water in the bottom to self clean is pathetic! I thought maybe it wasnt working and called for a repair since it was under warranty. The service man told me not to expect it to clean like a regular self-cleaning oven. But I complained that it did nothing at all! So now I have a self-cleaning oven that I have to clean myself!

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

Bought this as W/D set brand new from Home Depot. Had been noticing incredible wear and tear on clothes, as things get so tangled up and need to be practically ripped apart before going into dryer. Cycle times are crazy long, up to over an hour in some cases. Doesn’t have a “Speed Wash” cycle. But WORST of all, after less than 3 years, it just stopped draining properly. Tried all the Codes test, etc. Finally called a repairman just to be told repair costs would probably cost more than the machine is worth. $125 to be told we ought to just buy a new washer. Not happy.

My Bravos 300 series is 3yrs. Initially it occasionally shredded an item. With 4 kids I chalked it up to wear & tear on the clothes. Its now ruining items almost every wash. I now wash much by hand. Cant wait to afford a new one.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

Nobody seems to know how to replace this part online. I have discovered what a POS this Maytag MGDC700VWO dryer is. The ONLY way to access this part is to beat an access hole in the bottom-left panel. After the repair, you are left with a nice 4 hole??? What an absolute POS! The back panel has screws but after removing them, I discovered the panel is also tack-welded! This is beyond stupid! Maytag used to be a great product before they were obviously sold to the Yugo factory. Time to move on.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

Constantly does not clean clothes, always out of balance, codes constantly come up, only 2 1/2 years old and already rusting out. No matter what you do this washer does not want to work. Has special cycles for bulky loads but try to wash 7 towels and it will dance all over floor then shut down with an unbalanced code and you have to unplug to reset then wash towels again but not use spin and have to wring out towels by hand. I cannot believe the Maytag company has not recalled this very expensive pile of junk, and their service department is very rude and not helpful at all.Also as soon as you call an appliance repair company and tell them its a Maytag Bravos they say we do not fix those, do yourself a favor and junk it and buy any other brand. I have 3 kids now grown so we have bought about 5 washers over the years and when we saw that this was supposed to save water and energy and do bigger loads we were sold. Big mistake! Whatever you do never buy any appliance from Maytag. Products are garbage, service is nonexistent, and the cost will make you boil.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

Built a new house, bought new appliances for the kitchen. Like others, did all the research, wanted to buy American made. Wow, did we ever make a mistake. Refrigerator is just over 2 years old. It is worthless. Repairman, Maytag Certified, says that it appears to be internal problems and probably come from the factory that way. He suggested I contact Maytag directly and they should be able to make things right for me and my family.So, I called, sat on hold for 10-15 minutes, and was finally connected to a customer service employee. I explained all that I knew about the problem, she pulled the repairmans notes and the notes of the technician that had spoken with the repairman. After reviewing the file, she informed me that my 2-year-old refrigerator was out of warranty and there was nothing that could be done.What ever happened to American Made companies standing behind their product? I didnt spend $2000 on a refrigerator that would last me 2 years. I expected 7-10 years, AT LEAST! I expected a company with the name MAYTAG to show some shame for creating a piece of junk and charging a customer this much money for something they know is obviously flawed from the factory. Shame? No. Guilt? None whatsoever.Caution to those considering a Maytag product. Run away! Go find a more reputable company. Go find a company who views customer service and quality products as a priority. I didnt purchase the cheapest refrigerator on purpose. I paid extra for American made and what I thought was a quality product sold by a quality company. Reality has now set in.

Maytag calls peeling paint a cosmetic issue. With a convection oven it could be a toxicity issue. Waiting for an answer to my question as the fan blows the peeling paint onto anything that is not covered. Dont put foil on the bottom as this compromises the paint due to design. Truly sorry to have purchased Maytag as this line is not the Maytag we grew up with! Old school ovens and products had the quality or workmanship to last.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

Bought Maytag dishwasher 2007 at Lowes. Model mdbtt60aww-37837606ll manufactured in Benton harbor, Michigan. First got a recall that something was faulty, could cause fire, needed replacement. Took 2/3 weeks to get repaired. So couldnt use. Never quite cleaned good - many times had to rewash silverware, glasses. Never took off food unless very well rinsed. Today the control panel went. Called a local repair he said, Dont even fix. Toss and get a new one because its too costly to repair. I asked what should I get. He said no GE, they are getting out of appliances, no Samsung. Hes got whirlpool so guess Ill give that a try. In the past Ive had dishwashers 20 years, appliances 20 years. This junk lasts a year or two. Plastic cracks. None of these appliances are great anymore. Doesnt matter who you buy. Someone needs to get some quality control on what these companies are peddling .

I have recently purchased a washing machine. Within the first week I was calling a repair person to fix it. I HATE this machine, and I dont think that its fair that I get stuck with it because of the way it was made. I have to constantly redo the load because it doesnt drain and rinse. When the load is done the clothes are still soaked. I dont understand how technology can go backwards when it comes to washing clothes. SOOO DISAPPOINTED!!!

I would like others to know that Maytag does not stand behind this product at all. I am not sure about other products, but after talking to Maytags customer service team I would guess you would get the same runaround with other products. We have had our washers for about eight years now and have had many things go wrong with it. The one that gets me the most is the one that my appliance repair service does not cover and that is the main bearing. I have done some research to why this is and most of them do not cover this, because they should last for the life of the washer. Most washers last for more than ten years. However this washer has only lasted a few years on each bearing. I have now put in my third bearing into this washer. The last bearing only lasted two years. If I had to pay for labor on replacing this part I would have not replaced it. I had been given a quote for replacing it and it was over $350. Some places wanted more than $400 to do it. To me the washer is not worth this. Yes we paid like $900 for the washer, but it is not worth putting that much money into this washer. If you cannot replace this part on your own then just walk away from it. Buy a Speed Queen. I know Maytag has sent parts to other people free of charge, but I have not been so lucky. When you send others part to fix the same problem, to me that is admitting that there is a flaw in this washer. With that said my wife and I already filed a BBB complaint against Maytag and will be sending a letter to the Minnesota Attorney General. I have proof they have sent replacement parts to others and dont see why they cannot do the same for me. Maytag is own by Whirlpool, you think it would be cheaper and easier to make customers happy than just brushing them off. I would say that customer service in many of these large companies and even small companies is gone. I remember when you would call a company and make a complaint and they would go out of their way to try to make you happy. Now they come up with reasons why it is all the customers fault that their products are bad. Maytag is just another example of a greedy business that does not care about their customers. So please do your research before you buy this product and good luck to those who have that are stuck with the junk that Maytag sells customers.

First of all, Whirlpool owns the Maytag brand. Ive seen a few reviewers on here say I will never buy Maytag! Im buying Whirlpool from now on! I picture the executives smiling and nodding, Good. Maytag used to be great - machines lasted 20 years or more. Now they last about three. After one year, the paint on the washer was bubbling and coming off, and now its starting to rust. The warranty doesnt cover cosmetic defects beyond 30 days, and the warranty for the rest of the machine is only one year. Theres a reason for that - the machine will undoubtedly have problems after that. Multiple calls to Maytag/Whirlpool and they do not care. Terrible product, terrible customer service. I tell everyone I know never to buy Maytag or Whirlpool.

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

I’ve had my dishwasher for over 10 yrs now and I probably need to upgrade but it suits us just fine and I’ve really never had any problem with it at all. My dishes and especially my glasses come out Sparkling.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

My dog had to be on a special diet to recover from a stomach disorder. I placed 1/3 cup of dog food plus chicken broth and baby food in a bowl. I intended to heat it for seconds. Minutes later, my dog was whining and sneezing. I immediately returned to the kitchen to find the food and bowl were completely charred. The biggest problem however was from the plastic splash guard that melted down. Smoke filled my home. I had to call the fire department. I was coughing and had difficulty breathing. The smell was horrible!The insurance company and I have had thousands of money in restoration cost due to the damage. I was out of my house for weeks and got very sick due to returning to the home that was not remediated properly (allergies and asthma). The microwave was an over the range Maytag MMV4205BA. I would like to find out if the fire was due to a malfunction in the microwave oven. If so, Maytag should be paying for the damages. I still need living room furniture and carpeting replaced due to smoke damage.

THIS PRODUCT IS CRAP!!!! I spend $699.00 at Home Depot, after 1/12 years the console stopped working. Maytags engineering staff should be fired!!! You stole my hard earned money. NOT once, but on a washing machine as well. I will never buy a Maytag product again. HEY NO WONDER THE REPAIR man sits on his ** the rest of the company does too! I dont have 250.00 dollars to fix this thing. Shame on your company. No wonder you dont want anything. DONT BUY MAYTAG, buyer beware. I am angry but this is not **!

We bought a Maytag 2000 Series machine about 2 years ago. At first the machine worked great, as a new machine should. Then, after about 7 months water started pouring out of the top dispenser for detergent. I read the manual and looked online at the Maytag website for common problems. It said that sometimes small clothing gets sucked through the hose and needs to be unclogged. I followed the instructions to fix the problem. It worked fine for about 2 weeks later during the middle of a load the machine would stop and give me error codes. I looked these codes up and now I have another clog on the drain tube that needs to be fixed. Lo and behold these 2 problems have been continuing ever since. I cannot do a load of laundry without getting a code and having to take the machine apart. I called Maytag to explain my situation and the customer service representative said that because I fixed the problem myself at this point there is nothing that can be done. They do not guarantee that their equipment will work nor will they help solve the problem. I cannot believe that we spent so much money on something that I cant use. Not to mention the fact that when I do complete a load some of the clothes are ruined by the machine ripping holes in them. I would not recommend buying a Maytag because they dont care about customer satisfaction or the quality of machines they sell.

We purchased a Maytag refrigerator, model #mf12269veb on 2/1/12 and for the past few months it has been leaking water out of the bottom freezer unto my floor and ice is forming inside the bottom of the freezer. I have read many complaints about this and if there is any recourse to this problem please let me know. So disappointed with this appliance.

Both the washer/dryer are of the Bravos models and both perform amazingly well. It seems everything works so well, including the vents which are thorough and vent the machine well. Our laundry is always clean and the settings on both machines work very accurately! We believe our Maytags are simply the best operating machines weve ever owned!

MBL2258XES1 - Like most of the other reviewers, we have a Maytag refrigerator just 3 years old with a lower freezer that leaks water onto the floor -- and has been doing it for the last two years. We have to take the freezer apart (NOT easy), defrost it, take the back panel off, and clear the drain tube. Obviously a defective design! Cant believe Maytag hasnt done something about this!

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

Does a good job. The only thing it has problems with is frying pans, but no dishwasher can do those. 4 cycles, option to turn off heated dry. Standard size. Fit the cabinet perfectly. Just a plain white front, which is fine, but it did not get 5 stars because the white plastic control panel seems to catch and show dirt easily compared to the white painted metal door. Ive had this machine 15 years and the only repair needed was replacement of one of the rollers on the lower dish rack.

I have been trying to get my refrigerator repaired for over 5 months through the extended service plan I paid for. They sent out a service repairman. He could not repair the refrigerator without some parts so he ordered parts. We waited months to find out he can not get the part anymore that he ordered. So now Maytag Extended Plans and Service Power said they would have to replace the whole refrigerator but every time I call about it, they give me the runaround and say someone will be calling me back within 48 hours.I never get a call back. I give them a few days, then I call back and get the same runaround again. Im getting nowhere with these people. My refrigerator is a $6,500 refrigerator that Im sure they just dont want to replace or offer me anything for that matter. They should abide by the contract I have with them.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

I went to Home Depot in Kennesaw, Ga to purchase new W&D combo. I had found what I wanted but when the sales went to complete my order, the units I selected werent available. She talked me into the Maytag Bravo, but I specifically stated I needed a large tub because I wash a lot of towels and sheets. Well this expensive piece of shhh, doesnt even get all the items wet. Ive had to lift the lift and physically flip items in tub, especially with towels and sheets. Also, the washer is loud, did I say loud, I mean freaking loud. The dryer is fine, but I bought combo for a reason... Pricetag $1200.00 with my discount. I waited a week for delivery, I am mad as hell. Whats point of having large tub, when you barely get enough water. Luckily I found out now, so I can have them pick this CRAP UP, Do not buy. Theyre cute looking, but washer does not get your clothes clean.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

I bought a Maytag dishwasher, when I bought my house (7/2010). I live alone and I use my dishwasher only once a week or once every two weeks. After 3 years of working perfect, it stopped working. I had someone come look at it. After troubleshooting with the basic steps, making sure the water was correctly hooked up, a fuse was not the problem. The dishwasher door was shut completely. He took the racks and all movable parts, & thought something, a piece of glass, etc, was stuck in the drain. Nope. After reading these reviews I realize it is got to be the control panel because the start button will not come on and all these people have the similar problem. It just stopped. Period. The panel lights come on, but not the stop button. I am a single person as stated and on disability and on a very tight budget. I bought a Maytag because of the name and reputation. How long would it have lasted under normal use, say a family of 4, using it nightly? Certainly less than a year. I have no idea what to do now. I cannot afford a repairman, & I am certain it is the control panel on the dishwasher. I do of course have all the model numbers, etc & papers, when I bought it. I can provide proper paperwork, when contacted.

We purchased a new Maytag french door refrigerator and from day one had issues with the ice maker. After three replacements Maytag informed me that this was an inherent issues and no fix available. So we had a $2000+ refrigerator with a non-functioning ice maker. Our 20 year old Frigidaire continues to make ice with no issues. Then the control panel lights started blinking and evidently this is also a known problem and when I called Maytag to buy the part, they said SORRY we dont offer parts on our appliances over 6 years old. This is the worst piece of ** I have ever owned coupled with the lousiest customer service in the world. I will never buy another Maytag.

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

I will never buy this product again or anything with the Maytag brand. I purchased my washer less than a year ago and it makes all these awful noises. When called company they would not come fix it. Money wasted.

I had the microwave serviced and they heated a cup of water which was fine. I heat food on the tray and only one side gets heated. I have to turn the plate to heat the rest of the food. I never had that problem with a turntable microwave. I cannot understand why they are still selling this inferior product. Maytag used to have excellent products. What happened to this company?

I purchased an appliance package of washer dryer, refrigerator and dishwasher. All of the appliances needed many repairs. It took four icemakers in the fridge before it actually was fixed. The worst appliance was the dishwasher it was repaired every three months for six years! Washer and dryer died after five years.

Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

Bought a stove in May of 2014. In July of 2014 we noticed a 1x6 stain inside the glass of the oven door. I called Maytag and they stated only 30 day warranty on cosmetic flaws. I said this was not there when we bought it. They asked if anything had boiled over because if liquids get in the vents on the oven door it can get in between the glass. I stated no, only cleaned with Stainless steel clear. They stated most likely when I sprayed the door it ran down in between the glass. I said that is a flaw. They said, no the vents are there to allow heat out. I asked if they also were designed to let liquids inside the glass, they said no, I said design flaw. They will do nothing. I also pointed out that nowhere in the owners manual is there a reference to this possibly happening. Our sons in laws have a 3 year old LG stainless steel with vents and have never had this problem. Maytag will not stand behind their products even when they are the ones at fault. Buy a different brand.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

I am extremely disappointed with Maytag and the representatives I spoke with this evening. One laughed after I told her I was 7 months pregnant and without a fridge for a week after owning it less than a year. I was repeatedly and curtly told, We dont cover that, when I asked only to replace the recent food I had purchased. After having to request a manager several times, I was put on the phone with Dana ID ** who said she would not be able to help with any food despite the delay of a week for repairs to our fridge. However, she could extend our warranty for 6 months.The only reason we were able to get someone out as early as we did was because we knew a licensed Maytag service repair company. Otherwise, we would still be waiting for someone to come out to tell us it would be another week before repairs. The originally assigned service repair company by Maytag did not return our call. There was no concern or empathy from the Maytag representatives that I was pregnant and could have eaten food that was not cooled to prevent bacteria growth that would harm me and my baby.Even their service repair technician recommended to contact them about the spoiled food since it was impossible for the repairs to be completed before the end of the week. We will never purchase Maytag again. The appliance failed with no warning in less than a year, and the representatives made no effort to resolve our issue of being without food for a week.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

I have had this dishwasher for 3 1/2 years. Replaced the touchpad 2 years ago and now the touchpad is dead. I read all the other comments that are similar to mine and am thinking to replace this junk dishwasher. I will not be buying from Home Depot as they are selling cheap products that are defective!

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

My Maytag Series 300 Dishwasher would not start. I read the reviews and took the door off (easy if you have the right tool), removed the control panel box (one screw), and cleaned the ribbon with electronic cleaner as per someones suggestion. It started right up. This is a bad design. Would I buy another Maytag? - No way! We will see how long this lasts. There is no seal on the door to keep out humidity. Do we really need a new control panel? When this is done...I am done with Maytag!

I bought the largest Maytag top load washer. From day 1 clothes come out with laundry detergent left all over them. I have to take a washcloth and wash off every piece of clothing coming out of the washer. Had a technician come out. He said he gets this complaint every day. His suggestion, put less clothes in and use less detergent. This washer is programmed to use minimal water and it just doesn’t have enough water to clean all the detergent off. So, I bought the biggest washer to wash bigger loads and now you are telling me that just doesn’t work.Spoke with Maytag customer service. They said very rudely if there is no problem found when the technician came out, there is nothing they will do. She told me it was user error. My dryer also stopped working. Sometimes it would turn on, sometimes not. The technician said the lint screen error code came up. He would try to get Maytag to replace the whole board but usually they don’t do that unless the whole board has a problem. Called Maytag the next day. The technician documented he fixed a connection problem and closed the ticket. What???? So, now I guess I need to schedule another service visit. Very unhappy with 5 month old appliances. Paid $1700 for the pair, you expect quality products.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

I have had this washer (Maytag Bravos) less than a year and it does not clean my familys clothes at all. I have had to throw away clothes that are stained and ruined because this washer does such a poor job of washing. For the cost of this appliance, I thought it would do an excellent job, only to be disappointed. I have owned other Maytag appliances without a problem. This one is a disaster and has turned me against Maytag.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Purchased a Maytag refrigerator in July 2011. The compressor failed May of 2013. After many phone calls to Maytag they replaced the parts (compressor) - my cost for labor (aprox $300.00). 30 days later, the service company had to repair a leak and recharge the system. March of 2015 the compressor failed again. Have spoken to Maytag (case # **) - they will provide no help what so ever. I was told I should have purchased an extended warranty.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

I purchased this Maytag Bravos Xl Top Loading Washing Machine approximately 2 1/2 years ago. It broke down shortly after the 1 year warranty was up and cost me $300.00 to fix. A bearing had broke and needed a service call to repair it. Well, I paid about $800.00 to begin with, so decided to fix it. Today it started draining water from bottom of it. I call Maytag and after a 20 minute wait on the phone because they were having higher than normal call volumes! They cannot help me, other than to charge me for yet another service call and perhaps a repair. Whirlpool/Maytag makes a high priced money pit of a washing machine! Dont waste your money!

I purchased this machine and after 2 loads it started making a very loud and awful noise. Maytag sent a local service person and he found a screw that had come undone and was in the motor. Since then there are a few strange noises that the machine makes during different cycles, usually involving spinning. Called Maytag and then sent repair person. This young man was non-verbal, was probably 20 and it was impossible to communicate and try to figure this out. Person sat through a full cycle and he said the noises are because the machine is out of balance. Well, why did the sync system not balance at the beginning of the cycle. No answer to that. He reported to Maytag that nothing was wrong with the machine.Machine is still making noises and I cannot wash a small load or it will still be wet at the end of the cycle. I am a widow and live alone. I dont wash large loads. So I called Maytag again. They dont care. Finally they agreed to send another 2nd opinion. I have a lot of videos of the machine making strange noises and the repair kid does not care...lots of blank stares from him. I highly suggest not going with Maytag. They dont back up their products and they leave you with a bad machine. My LG FL was perfect. Never an out of balance load. I could wash a single item with no problem. MAYTAG IS A TERRIBLE COMPANY.

We purchased a Maytag 4000 series washer and dryer in October 2011, and within 5 months, the main bearing failed. The Maytag repair person told us it was an inherent issue and to make sure we use HE detergent (We always have.). Maytag advised parts were not available for 3 weeks, so no washer after 5 months of use. The bearing failed a second time after 11 months. Maytag refused to replace the washer and advised it was repairable condition. Now, we have the bearing fail a third time, and Maytag has advised that they would not repair the washer under the extended warranty program. They offered us 75% refund on the washer (So I guess they expect their products to only last 4 years.), which is simply unacceptable. We are now faced with purchasing a new washer, which will not match the dryer; or we have to purchase a washer and dryer of another brand. Maytag has provided pathetic customer support, and their response or lack thereof shows that they simply just dont care about their brand image or the customer.

Fifteen months after purchase, the lid lock and motherboard goes off. It was replaced with new parts and the machine still doesnt work. Cost of repair is equal to the cost of the machine. With or without an extended warranty, the expense is not worth the investment. While shopping to replace the machine, the dealer finished my sentences on Maytag washers.

The control panel of my dishwasher is malfunctioning. I looked this up online and ran into a recall for the heating element. Sure enough, my dishwasher is effected. I asked why I was not contacted. First they made up a story as to not having my contact information. This is simply not true, as I purchased the dishwasher directly from Maytag. Three years ago there was another recall and the heating element caused another problem so Maytag replaced my dishwasher.If a heating element overheats, it seems to me that a short-term affect could be overheating the control panel, causing it to malfunction. I read through a few recent complains and would also like to inquire about having this issue looked into by the Consumer Affairs.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

Maytag Bravos Commercial Washer MVWX500XWO - This has been the worst experience with this $900 washer and breaking down in less than 2 yrs. Complete Garbage, New Locking Mechanism, now spin cycle not working. I am about to take back to Home Depot and let them have it. Garbage product - NOT WHAT MAYTAG USE TO BE... NORMAL 10 YRS NO ISSUES THIS MACHINE - STAY AWAY FROM.

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

I purchased this five-burner gas stove two years ago. I have this stove repaired three times. The first and second problem with the stove is when I turned on the oven, it would never click on. This was a month after I purchased the stove. They sent someone over to correct the problem and that did not work. The third time someone came. He changed something in the oven and it started to work. After that, I continue to have trouble with the oven. When I have the top eyes on, the oven will not work. When I only turn on the oven, it will go to 350 only. It will cook for an half hour and then cut off. I smell gas in my house and my food is smelling like gas. I have stop using the oven. I did not purchase a stove to not use the oven. This is totally ridiculous!!! I am tired of this situation. Maytag needs to recall these ovens, so I can purchase an oven that works. I have thrown food away because it smells like gas - because the oven will cut off in the middle of cooking. I am very tired of this situation and when you call Maytag, their customer service is terrible. I will never buy Maytags products again. Please help.

I just bought a brand new Maytag microwave a few weeks ago. The door is already broken! I’ve been sitting here 4 hours! waiting for a repairman man. No call, no show! I am missing work and gym time because MAYTAG sold me a faulty microwave in the first place! Never again will I buy Maytag products!

I have owned my Bravos XL for over a year. Loads of wash have come out with rust marks. These marks do not show up on all items, only one article of clothing/sheet/towel seems to pick up the rust marks (usually a couple of dots near each other surrounded by a circle). They are always the same. They have shown up on sheets which were washed in a white cycle and on other clothes of various colors.I have ruined numerous new clothes and must accept the fact that these random but frequent rust-colored dots are part of my life. I expected more. Im getting ready to purchase a W/D for our home up North and believe its necessary to return to a basic model, probably a GE. Maytag seems to have jumped the gun on this one… putting new product out there, aware these unresolved issues remain.

My machine is only 14 months old and will not even turn on. I opened the lid, and the tub was filled with water and the wet clothes sitting in there. There were only 6 items in there: 3 school skirts and 3 school pants, dripping wet. So I unplugged the unit to try and clear the circuit board - to no avail. The machine will still not turn on. The lights are on, the sensor turns on for about 3 seconds and shut off and everything just sits there. I did not get the extended warranty. My mom still has her Maytag she bought 30 years ago and its running like a champ. Wish I could say the same. I gave my sister my old Maytag - its 25 years old and its still running like a champ. This machine is a LEMON. I will never buy another Maytag again. I am so done with this brand. I hope that a Class Action suit is filed against them.

To anyone out there who is considering purchasing a Maytag washer. My husband & I purchased a Maytag Bravo top loader washer from Sears Hardware here in Columbus, OH. We had always received great review regarding Maytag products. This washer is expensive & does not work. We started having problems from the day we purchased & had Sears come out three times for repairs. This washer has a built in scale which is extremely sensitive. We are very disappointed in this washer. It takes an entire day to do 3 loads of laundry. The washer goes off balance on every load. It doesnt do a god job cleaning the laundry. I do not suggest the Bravos series to anyone consider purchasing this product. It is a piece of JUNK! We purchased in Aug 2010 and the washer will need to be replaced within the next several months. Keep in mind that more expensive & lots of fancy extras doesnt mean a better quality washer or dryer. Stay away from Maytag or you will have the Old Maytag repair guy @ your door frequently.

In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

Have had this set for about three years (was a gift from my parents on having our first child), and its horrible. Clothes come out partially dry, with NEW stains on them, torn or frayed, and twisted into knots. Its supposed to be a high-efficiency washer but we often have to wash things twice to get them clean. We now have two little boys and Im starting to save to buy a different set (no Maytag ever again); disgusted that I cant even sell this set in good conscience. Will either be a donation or an eyesore for the landfill. Worst $1100 ever spent.

At two different times today I was left on hold for thirty minutes each. I was told the compressor only had a year warranty on it, cant do anything about it. I then went online to Maytag web page and it read only on compressor the warranty had ten years. I called them after a very long wait and was told that was just started with the ten year warranty. I have owned many different refrigerators never heard of compressor only lasting 5 years. The serviceman who came out to tell me compressor was bad said the name Maytag used to stand for something but now stands for junk. Worse customer service, worse product.