Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

Brand New 2019 Model 465 Washer and like others are saying is a piece of junk as they do not fill the drum with enough water even on the Deep Water fill option. The laundry does not circulate and nothing gets clean. Maytag is really poorly designed and manufactured these days and a complete Rip Off!

I purchased a Maytag refrigerator about two years ago because of the Maytag quality hype. The ice maker has been leaking almost from day one and I need to clear out the ice from the bottom of the freezer every few weeks. Now the thing has quit cooling all together. I contacted the Maytag website and they recommended a local authorized repair firm. I took a day off work to meet the service provider. After checking the fridge they informed me that the problem was with the sealed system and that they could not work on it, and that I would need to contact Maytag to get a real Maytag repair person to come and fix the thing (right back where I started). They were however more than happy to charge me $70.00 for a service call. I tried the Maytag 1 800 number which was a nightmare and it finally hung up on me. I then went back to the website and managed to get a service appointment in two weeks (had to wait for a Saturday appointment because I cant afford to take another day off work). I just hope that this time it will actually be someone who can fix the thing and not charge me just to refer me back to Maytag again. I am not happy with the so called Maytag quality or their BS methods for providing service. Caveat Emptor if you are contemplating a Maytag appliance.

Maytag Bravo X-We bought this washing machine not even 4 years (February 2013) ago from Lowes. We had this issue before the warranty went up a couple of times and then it stopped and started working fine. We contacted Maytag before... But of course beings the issue resolved there was no way to send someone out here to troubleshoot the problem. Now it is doing it all the time. A few months ago it went out of warranty. We are having issues with it going into the spin cycle and it will stop there and it will not spin out my clothes and finish draining. Contacted them and they want to charge money for a service tech to come out just to look at it. Lord only knows how much it would cost to fix.

I have never owned a Maytag in my life but was told it was the best on the market. That is so wrong. I purchased my Maytag Bravos washer and it has been a nightmare. Never again will I buy a Maytag. I have replaced two belts. It never spins the clothes out. Always have to restart it to respin. It turns off in the middle of the cycles. It will take hours and hours to do one load. At this time it just puts up the minutes and counts them down...does nothing. I am just fed up with this washer. I also bought a Maytag Centennial Commercial dryer. I have replaced a belt once. I would highly recommend not buying the Maytag Bravos washer. Save yourself the headache.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

I share the complaints of others about the Maytag Bravos washer (model MVWB300WQO), which I purchased in October of 2009.Besides being overpriced, its a washer that doesnt soak clothes, develops a bad odor, has silly things like unnecessary lights and music, and you cant add an item once the wash cycle has begun without the cycle starting over from the beginning. It also leaves washed items in twisted wads and the lid locks so you cant see whats going on inside. In addition, it damages items. Ill have to replace a full-sized blanket that it recently destroyed and now I cant trust that itll wash things safely, which is a problem. The person I spoke with at the companys customer service department simply said that I shouldve used the bulky item option instead of the regular cycle. I explained that Id used the bulky item cycle before and the same thing happened. The washer leaves larger items stretched very tightly across the tub and I suspect that is how my lightweight cotton blanket was destroyed. She offered to schedule someone to service the washer. But its not broken, its a poor design, so sending someone here would be a waste of time.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

Was coerced into purchasing this fridge three years ago. Told how Maytag is the highest quality fridge etc. From day one it was noisy and seemed to be running half the time. I had asked for a quieter fridge, partially why I paid $2000 for it. Now there is something wrong with it. Not sure what yet. But for $2000 it should not be failing three years later. My Samsung was quieter, 1/3 of the price and lasted at least 8 years. Thought about calling customer service but read too many bad experiences here in regard to that. Will never use Maytag again.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

Currently own model MTB1504ARW, serial number 12541413GT refrigerator. The defrost thermostat broke and it is causing the device to frost over and not cool. Maytag is trying to replace the part with part number 63001051 and that part does not match the part that came with the machine. I spoke with a supervisor, Mr. ** who certainly was not a problem solver or any help, in other words, lacks customer service. I explained the installation of the wrong part may be dangerous and could cause a potential fire or hazard. He assured me this was the part available, but also said it was discontinued and I would have to find it with an outside vendor. I explained I compared the part removed and the part they are suggestion, per the part list, and its the wrong part. As a supervisor, Mr. ** failed to provide true customer service for myself and future customers who may be in the same situation, with the potential of causing a hazard for customers. The Maytag supervisor should learn to provide customer service and prevent possible hazards for customers, taking the next necessary steps or research the issue with other departments within Maytag. The parts below are evidence of the issue, the suggested part has two wires, the one from the refrigerator has three... poor customer service, at best with potential hazards to families and children. It may because their appliances dont break, according to their commercials, they just have too much time on their hands and cant provide the assistance that is needed.

Maytag Bravos Quiet series 300 washer - I purchased this washer 14 months ago from LOWES. After having a huge issue with a Kenmore Oasis machine. $$$. Anyway, this machine started a week ago with F1 code and Ld code. This is getting to be a financial strain buying washers every year or two. This is my third in 5 years. Looks like I will need to get another one, again. It makes no sense to repair it at a high cost when the replacement parts are the same as the failed parts. Everyone seems to have the same problem with this washer. Get better electronics guys. The rest of the machine is in fantastic shape. My two cents.

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

The control (computer) stopped working. The Maytag Centennial washer would not turn off. I had to unplug it from the electrical outlet to get it to stop. The repairman had to replace the computer panel. He said it had burned up. I bought this machine from Lowes on January 11, 2011. It lasted 15 months and cost me $265 to get it repaired. I called Lowes and because I did not buy the extended warranty, they would not even talk to me. When I pay about $500 for a washing machine, I expect it to last longer than 15 months! I will never buy another Maytag appliance! Customers beware: these products are a bunch of junk. Even the repairman told me so.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

I, too, am having major problems with my Maytag Neptune washer, much like many of the writers are. I am extremely disappointed in the Maytag corporation for putting out such an inferior product that it wont stand by. I wonder if a new class action suit could be filed.

Stay away from Maytag Bravo washer. We bought one a year ago and fought with them this whole year. It leaves lots lint on clothes. Weve had 2 technicians here 4 times. Now they finally said we can replace but will only get a prorated credit even though its been junk since day one and we contacted them immediately. If we wouldve known they wouldnt stand by their warranty we wouldve hauled it back to store for full refund. They dragged us along a year and now warranty is no good but they will prorate. Not fair at all.

We purchased our Maytag fridge on May 13, 2013. On June 19, 2013, it stopped working. We called Home Depot where we bought the fridge and they told us that we would have to deal with Maytag. What a nightmare. The repair guy came out and ordered a compressor for the fridge. 2 days later, when the compressor came in, the repair guy told us that the fridge was unrepairable. Great, what was I supposed to do with this hunk of metal now? I called Home Depot back, and they ordered me a new fridge, added a five-year warranty for free, and the Store Manager even dropped off a small dorm size fridge for us till our new one came in. Yeah for Home Depot!!!! I would recommend no one ever buy a Maytag product again - what a piece of junk. Their customer service didnt even care; they had the same old story - We will get back with you in 72 hours. Maytag was good when it was built in the US; now its just more China Junk.

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

We spent $600 on a Maytag Jet Steam Plus dishwasher and its junk. We bought it in May of 2013 and the top panel is burnt out and the ribbon or control wires is corroded. Maytag wont pay for replacement parts and I wouldnt recommend anyone buy Maytag again. I thought it was supposedly a good brand but its nothing but garbage.

I bought a Maytag dishwasher to match other appliances in kitchen. Work great, not loud and gets dishes clean. Have owned it for 10 years and have one problem with the door latch. But it was easy and inexpensive to replace.

I have had a Maytag Bravo Model MVWX500XW0. Bought less than 3 yrs ago for over $550. Four days ago, the drum would not turn during wash or spin. It would act like it was going to turn but then the door lock lid kept flashing. Today Maytag repairman came by and put in a new lock circuit. Instead of fixing the problem, it made it worse. The washer started making rapid clicking sounds and finally the lid lock stopped working altogether. The repairman could not get his computer to even do a diagnostic. Instead he calls his boss who says it must be the motherboard, a $300 part. My research indicates that Maytag almost always says replace motherboard and customers find that doesnt work either. Ive never had a washer last less than 10 years. Three years for a high-priced washer is mind boggling. Ive also never had a repairman make things worse by installing new part but that happened. I will never buy a Maytag product again, even if its owned by Whirlpool, which used to be a name you could count on.

Bought all stainless steel Maytag appliances when we remodeled our kitchen in 2010. French door fridge freezer broke down three times. First the fridge lost its temp and we lost our food. The freezer went into overdrive and froze the vodka solid. Second time massive ice build up in bottom of freezer so we had to constantly chip it away to keep door closed. Third time was a repeat of the fridge not working at all and the freezer going insanely cold. Sad to say, we have given up and bought another fridge freezer for $1,500, not a Maytag!On to the washing machine: a super duper top of the line expensive Maytag. At the end of last year it started to make disturbing jet engine noises in spin mode. It for worse and worse so I had a repair man come and take a look at it. He said it would cost over $700 to fix. Once again, we decided to cut our loses and buy another washing machine. I have saved all the paperwork including the repair bills for both appliances so Im good to go on the class action lawsuit.

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

My parents always bought Maytag and so did I. Ive experienced minimal problems in the past and have done my own repairs. My new MDB4949 dishwasher is GARBAGE! Imagine coming home and seeing water flowing out of the house under your back door! The water was coming from the kitchen across the kitchen floor and cascading down the stairs like a waterfall. I pressed the cancel button, nothing? Opened the door, NOTHING! Shut off the circuit breaker, NOTHING!Water continued to flow until I closed the supply valve! The dishwasher damaged my home! Six service visits later and still not fixed! 9 days out of warranty and still having the same problem! Customer service told me to hire a plumber to fix my plumbing problem with the dishwasher water supply! Thats funny because 3 other dishwashers (in the same exact place) had no problem with the water supply in the past 23 years? Two of them were Maytag!I never give less than a positive review but, this is outright FRAUD! The dishwasher has damaged my home on 2 occasions! Unless I want to stay home the whole time its running I cant use it? The customer service is pathetic at best. The control board issue is a scam by every company. Its all designed to keep you on a service plan and is a scam! Long gone are the days of the reliable rotary timer/control that lasted forever! You can thank everyone you know for not paying attention and letting this happen! I guess we can wash our own dishes by hand or comply with this obvious scam?

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

Our Maytag Bravo washer provided so little water, that our clothes were rarely clean. My husbands jeans gradually developed stains around the knees that never came out, and his white underwear & socks didnt come clean either. After about 3 years, the spin cycle developed a loud sound, like a jet taking off, which was so loud and forceful, it sounded like it was literally going to spin out of the machine. We got rid of the Maytag Bravo after 6-7 years, and Darryls jeans and underwear were clean after two washings. All heavy items, such as blankets, have to be watched over because they always get out of balance several times a wash. We kept the Maytag Bravo, although it wasnt great, and didnt dry clothes completely. These are not machines that you can put clothes in, and just walk away. You have to babysit your laundry.

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

DO NOT BUY MAYTAG REFRIGERATOR. I purchased a Maytag refrigerator 3 years ago, now it started to leak water on the floor. Repairman said this happens after about 3 years to all Maytag refrigerators because the water hose is too small and gets plugged which causes water to flow into bottom of freezer; 2 inches of ice on bottom of freezer. Now we have to remove everything from freezer and refrigerator, unplug for 2 days to melt ice so we lose all of our food in freezer and refrigerator.

I purchased a Maytag top load HE Bravo 700 3 yrs ago. I only wash 3 loads of laundry a week and the bearings went bad in the washer! Maytag/Whirlpool will do nothing to help me because they say I should have purchased the extended warranty. Well there is NO WAY that I could have worn out those bearings; it was a manufacturing defect that caused them to fail and hundreds of people online all say they have the same issue. The repair cost is $400 and would only have a 90-day warranty so I might as well purchase a new washer. Home Depot (where I purchased the washer) has been very helpful and is offering me help on the purchase of a new washer, but even they could not get Maytag to do the right thing and repair my Bravo. I am going back to a none HE machine with an agitator. This has been a horrible experience and Maytag has no business putting commercials on TV that say they are dependable.

I bought a Maytag washer, dryer, and a dishwasher from Home Depot. It has only been a year and 1/2 and the washer has already broken down. Maytag wont help and neither will Home Depot. We are two elderly ladies (sisters) that used it once or twice a week. I feel we got ripped off. We cannot afford parts, labor, or a new washer. This product needs to be pulled. And Home Depot should not sell anything that is not a better quality. I trusted both companies and am sorry I did. Thanks.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

We purchased a new Maytag side-by-side refrigerator back in 2011 and for the last several months it has been leaking water into the bottom of the freezer unit when it goes through the automatic defrost process. The water freezes and after a few of these cycles causing the ice to accumulate and build up, it starts to leak out onto our kitchen floor. About every 10 days we have to open the freezer door, break up the accumulated ice on the bottom of the freezer and remove the ice chunks by hand. What a pain in the neck! Most of the time we can prevent the water from escaping, but not always. This is going to damage our kitchen floor, not to mention its a safety hazard for slip and falls, and/or fire or shock hazards. We have contacted Maytag directly, but nothing will be done as they say its beyond the 12 month standard warranty. They said one option is for us to purchase an extended warranty plan from them for only $359. Really? Are you kidding me?? They dont seem to care about a potential product liability property damage claim/suit, nor an exposure for a potential bodily injury claim. As Ive tried to explain, this is NOT a warranty situation, its a product defect situation and one probably worth a class action lawsuit based on the number of complaints Im aware of. They know its a product defect problem, but choose to ignore it at the expense of numerous innocent consumers. The only resolution seems to be filing your own lawsuit against them for some kind of remedy to this very aggravating situation that occurs every 10 days or so. Maytag used to be very good appliances, ones that were made of high quality materials, and lasted for years without any problems. Thats why I became a Maytag fan in the first place, but ever since they were purchased by Whirlpool Corporation, its not the same old Maytag we used to know and love. DO NOT BUY MAYTAG APPLIANCES - you will regret it!!

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Well, I thought I was buying quality products dishwasher and refrigerator and both are very disappointing. Of course the Maytag dishwasher (MBD7749AWB2) really upsets me since I just bought it in Aug of 2011. Now it will not finish a load of dishes and I did what the lady at Maytag told me. She said it was the control board. But it is not the control board. It is still working the same as it was. Now what should I do? When they said I had a 10year warranty I didnt think a known product like Maytag would let me down. MAYTAG, YOU SHOULD BE ASHAMED TO ADVERTISE YOUR PRODUCTS TO LASTS! THEY SUCK!

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

Things that I have read that are true: Rips clothes/towels/sheets. No real problems with motherboard like some have stated. Bought Maytag Bravos Washer/Dryer in 2009. No real problems with the dryer, HOWEVER, may with the Washer. Had the pump go out in 2/2010 to the tune of $199.20 due to a small object in the pump. The repairman said it would just take a very inexpensive part from Maytag to prevent this. In 6/2012 washer not draining, clogged pump. All right, new to HE Washers, so told to use less detergent than detergent manufacturer recommends. $79.13 to fix clogged drain. Even though being careful with items in pockets, loose buttons, etc. AGAIN had pump go in 1/13, $214.22 (same problem cheaper in 2010, repair inflation). Wed noticed it was loud on the spin cycle (like a rocket going off) and were told at that visit the bearings would need to be replaced, and quoted approximately $280 to repair those. Havent fixed, waiting for something else to go wrong and then decide what to do with it. So in 4 years paying almost the purchase price of the unit (if I fixed bearings also). Crazy. If you bought a house and had to pay 4/5 of the house to repair it in that short of a time, no one would own a house!!!

We purchased a refrigerator in December 2013. It quit working less than 8 months later. The company contracted to repair it made us wait 4 days for service; they did not repair the unit. We are now expected to wait another 4 days for them to return. STAY AWAY from Maytag!!!

I purchased the washer and dryer approx 6 or 7 years ago. Out of the gate about a year the pump had to be replaced on the washer- 2010. 1/2012 the tub needed to be replaced, 6/2012 the PUMP needed to be replaced again! Then 2013 the dryer need a new board at the tune of $391.00. And today, yes - yet once again I need a new pump! Over $2,000 in repairs on these awful machines. I called Maytag because I thought maybe they would care - not so much. The rep told me that the Bravos models were discontinued (shocker) but that she could give me a discount on a new comparable version at ONLY $600. How nice! I will use these until they fail again - which according to history - that wont take long and then I will NEVER EVER EVER purchase a Maytag product again. We work hard for our money and continually giving it to a company (for parts) for a product that they failed to make a quality product is not going to happen again! DO NOT BUY MAYTAG. Do your research and give your money to companies that care. MAYTAG should be held accountable and a class action suit should be filed. They need to GET IT and they never will if we sit back and let them take advantage of consumers.

I always thought Maytag was the best, maybe because of their ad. Finally, I bought a refrigerator two months ago, which has turned into a nightmare. The company has sent a tech six times and they all say that it is a bad design which makes my vegetable drawer full of water because of moisture. And they refused to do anything about it every time (bad management). They have already spent more money on service than what I paid for the refrigerator. Figure that out.Do not buy Maytag. It was the biggest mistake I made. I also bought a washer and a dryer at the same time. I wish I could send them all back because of the ignorant people they have working for them in their complaint and service office. Anybody out there, if you want to buy an appliance, make sure it is not Maytag.

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

This washer was the biggest disappointment I have ever had. When I looked at it in the store I was excited that the tub was so big and the Maytag Label has always been trustworthy to me and my family. This machine certainly has disillusioned me against Maytag. I can only wash clothes on the bulky sheet cycle because even with deep water wash it only puts about 2 of water to wash clothes. Clothes on top dont even get wet! It doesnt take an engineer to figure out that you cant wash clothes without water. Big mistake! Would never recommend this washer to anyone! I complained directly to Maytag and never received a response. I have had to rewash clothes because they did not get clean. Even with an extra rinse the clothes still have enough soap in them to make my skin irritated. My whites are not white even though I use hot water and follow all of the directions provided with the machine. If there was any way I could afford it, I would throw this machine out to the garbage and get one that actually cleans the clothes. I will never buy another Maytag machine in my life. 

This washer does not distribute enough water to wash clothes properly. I continually take clothes out of washer that are not completely wet. My darker clothes have white spots of detergent on them that did not get rinsed off. This product should be pulled from the stores. We have tried everything, using deep water wash, bedding wash, to get more water in the machine. Our clothes are not coming out clean. Complete waste of our money!

Hello, I purchased a Maytag Bravos washer model MVWX655DW from the Home Depot in June of 2017. I can provide the receipt. Within 6 months I had a broken lid switch and the unit would not move through the cycles. Luckily, I had the ability to replace the lid switch at the cost of about $100 just for the part. The repair was fairly involved. This summer, the unit failed to agitate, upon much research, I learned the washer drive hub (which makes the washer agitate and spin) was worn out. It was made of plastic and it is quite a job to get the cover plate off and to replace this part which ranges in price from $20-$45. This is a fairly difficult job and I would not recommend it to most people. It should not be needed in a 3 year old machine. Upon inspection of the drive shaft teeth when I took the washer apart, I found the steel teeth to have significant wear. Why? Now, in mid-November, same issue, the plastic drive hub is worn out again! I was told maybe my shock absorbers for the drum needed to be replaced as the drum may be shaking too much. My previous washer was good for 18 years and I replaced it with this highly recommended model Maytag with the chrome basket. This is absolutely the worst appliance I have had and with every repair, I viewed many, many people with the same complaints and feeling that Maytag should issue a recall on these machines. I will be contacting Maytag and Home depot with my review. The HD installer also stripped the plastic valve one of the water hoses goes on that I had also to replace. A $40 dollar part. This took some disassembly but not as bad as replacing the drive hub every three months. Needless to say, I have to buy a new machine after 3 years of unreliability with his machine. A waste of $500 + of my hard earned money. Very, very disappointed. If I wasnt mechanical and able to fix this washer, it would have cost me hundreds in repair bills. I have receipts of the parts I have purchased for this unit. I hope your experience is better if you have owned one of these machines. Maybe I just got a bad one but many people have complained about this model so I dont believe I am alone. I hate to see good people spend their money on poorly constructed machines. I certainly expected more than 3 years out of a brand new appliance. Maytag and Home Depot have lost a good, long time customer unless they want to make it right. Please feel free to contact me.

We purchased a Maytag front load washer in May 2006 (MAH6700AWW). In November 2012 we had a leak and called a repair service. We were told it was the dispensing hose which had a hole worn in it and was replaced. In February 2014, we called the same service and was told that we had the same problem. Now in November 2014 we are experiencing the same problem. We have notified Whirlpool of this problem and each time were told that the machine was too old to reimburse us in any way. Guess who wont be buying any Whirlpool products if they do not back up their faulty workmanship.

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

My dishwashers warranty expired in March 2011 and it stopped running in April 2011. I have not had the use of my dishwasher since then. I was able to finally afford to have a technician take a look at it. I am told that it is the circuit board and it is going to cost as much as the price I bought the dishwasher for. I thought Maytag products were better than the other products so I paid a little more and got a Maytag only to find out that they are garbage. I might as well bought an unknown brand at a cheaper price for all your products were worth. I guess you cannot trust anyone these days, and I will never buy a Maytag product of any kind again. I think that you should fix this.

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

We bought a top load washer and the matching dryer. A thermal switch (I think it’s called) blew in the dryer at about two years. Luckily my husband is an electrician, so he took care of that. WASHER-A little after 2 years the plastic “driver hub” stripped And the agitator has stopped working, the door is having trouble locking and it won’t spin fast enough to get the water out of the clothes. I’ve ordered a new “driver hub” for $53! It is a cheap plastic part. Probably 1 cent to make in China. Robbery. This will hopefully resolve all 3 issues I’m having with the washer. They even charged me 9.99 shipping. $2000 later Maytag/Whirlpool should treat their customers like royalty. I will never ever buy another Maytag or other brands associated with Whirlpool ever again.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

I purchased a Maytag 4-door model, a little over three years ago. A little over a year ago, I noticed small puddles of water around the bottom of my refrigerator on the floor. I blamed the dog for having accidents and shrugged it off. Well, after months of putting up with this I came to the realization that it wasnt my dog, so I started looking for leaks on the seal, etc. Thats when I realized that the entire floor of the freezer was one solid block of ice! So, I looked online for people that might be having the same problem. Sure enough, there are A LOT of us!!! Now to add insult to injury, I have to have a MAYTAG certified repairman come and look at what needs to be done! He only charges $85.00 just to come to my house!!!! Thanks MAYTAG, I spend $2500.00 for a refrigerator thats obviously defective, and still have to pay more to have it repaired!!!

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

I purchased this oven about 6 months ago. This is my second Maytag oven which I had for 18 years. I am extremely disappointed in the quality of this oven. I did my homework and shopped around and chose another Maytag. First, the ignitor clicks and clicks but doesnt ignite. After 4-5 times I have to shut the oven off and restart it. But worse than that is the enamel on top. The quality is HORRIBLE. You cannot use anything but a soapy sponge to clean the top. With my last oven I was able to use anything (softscrub, ajax, the scrubber side of a sponge) and the top was shiny clean. My stove top is covered with scratches and is not even thoroughly clean. There are grease spots around the burners that if I scrub any harder Ill take the enamel off completely. Very, very poor quality. Will never buy another Maytag.

Had this model MDB7749SBM1 for almost 3 years and paid over $700 for it. Thought I was purchasing a good machines. The last few months the control panel pops out and away from the front door panel. Do get it back. You have to unscrew the panel from the door. Inside is all plastic and broken. How can it be broken when it is an area never touched. Every time you open the door after a wash it pops out again. To get it repaired will cost too much. It is a badly designed unit which should have a latch instead of just pulling out.I am so disappointed and will think twice before buying Maytag. I have never had luck with any Maytag dishwasher lasting. At this point I dont know whether to just buy another brand or glue it. We are not keeping our home so I dont want to invest money. Awful machine and I see it is discontinued so there are a lot of complaints. Thanks for sticking us Maytag.

Dishwasher MAYTAG MDB7749SBM - Have the same problem as everyone else, panel board. Initially lights randomly blinked, flashed etc, but still washed dishes. Now it has completely died. Dishwasher is 3 years old.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

Purchased Maytag dishwasher model MDB7609AWW2 3 yrs ago. Started having problems with it not filling with water after first cycle. After examination determined that the control panel/handle on the top of the door had broken away from its attachment points/screws behind the pane. Every time the door was opened this would allow moisture and steam to infiltrate into the door interior. And guess what, it now needs a new electronic control panel. After seeing all the other reviews, it is safe to say this is not the Maytag of our parents or grandparents.

1. can not get enough water in the Maytag machine to cover the clothes. 2. All of the clothes come out twisted. 3. After watching the machine wash the clothes I notice that agitator did not move all of the clothes down into the water, and that was probably because there was not enough water in the tub. 4. The machine gets out of balance easily and at that time the machine door is locked and you need to push the pause button and wait for it to unlock the door. 5. Its louder than my old Kenmore washer that we have had for 15 years.6. The Maytag dryer does not dry as fast as my old Kenmore dryer that we have had for 15 years.Bottom line is I would not buy another Maytag product. Do your homework.

The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

For the first time I bought a new washing machine in order to have one that lasted. Bought a brand new Maytag Front Loading HE washer model MHW3505FW1. Controls stopped working and the machine turns on and off by itself. Its either a faulty control board or computer, either of which are going to be more than a $400 repair. So more than half of what we can pay for a new machine. Maytag only warranties two parts for more than a year. So in reality, its not worth the repair and I will not buy a Maytag of Whirlpool product ever again.

I can see by the comments on this page that the letter I sent to Whirlpool was in vain. I purchased a Maytag double oven gas range (MGT8775XW00) from our local Lowes. We were remodeling a home we had purchased. Unfortunately (as anyone whos been involved in home remodeling/renovation knows well), it took much longer than I thought it would before range could be installed. It was several months later before it was installed. First time I tried to use the top oven, it would heat to set temp (I assume) and then shut down. The larger bottom oven had erratic heating. I tried adjusting oven temps but it was a guessing game. We had Fix-Rite Corp out twice and they were puzzled by the problem. Two times, they replaced the control panel. After the second repair, it was decided the only thing to fix the kitchen was a complete gutting, new cabinets and floor. The oven was pulled out before I had a chance to use it again. By the time we got the kitchen finished and range reinstalled, I discovered the oven still had the same problems and the broiler would ignite sometimes and when it did, the flame would go out after 30 to 60 seconds and would not come back on. By this time, we were past the one-year warranty. After the first repair did not work, I tried to get Lowes to take it back and assured them I would purchase another range from them. They said they could not do that. Now I can see Im going to end up buying another range. Be assured it wont be Maytag and it wont be Lowes. I also own and use Maytag washer and dryer.

We purchased our washer/dryer in June 2004. I have tried to clean off the rust where the water enters, but not successful. Is there any way to have this replaced at no charge?

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

I write this as the repairman is fixing my Neptune washer. As with many other complaints, I was experiencing the awful mold smell with the only fix being leaving the washer door open when not in use. This works but for the past few years a switch on the front broke which means we have had to leave the top off the washer and rig it every time we used it. Sometimes it would work and sometimes an error code would show and I would have to just turn to spin and finish that way. At the same time in 2005, I purchased all Maytag appliances. First the microwave went out then the ice maker broke and is still broken, then the dishwasher went out and had to be replaced. Washer broke so basically the only thing that has had no issues is the oven and all happened just outside the five-year warranty. Never again will I buy Maytag.

Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!

This is the absolutely worse washer I have ever owned! My clothes actually come out dirtier after they are washed. It leaves white stains on clothes that I have to scrub out by hand. Maytag you should be ashamed of yourselves for coming out with a washer like this. It takes me 2 or 3 times to wash clothes and I have to use the power wash, extra rinse, and maximum clean setting to even come close to cleaning. It is cheaper to take my clothes to the dry cleaner now than use the washer. I called Maytag numerous times, and they said that they will charge for a service call unless there is actually a mechanical issues. They will not honor repairing the machine if it does not wash clean. I will definitely NOT recommend this washer.

We bought a Maytag refrigerator about 3 years and have had so much trouble. The freezer section which is on the bottom half leaks water periodically on the floor unless, we take the bottom rack out and pry the ice from the shelf about every week. It started doing this about 6 months ago and well need to get a repair man out here. The doors on the refrigerator are also a problem. They often dont close properly, so one is partially open, but unless you look directly at it, it isnt noticeable.

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

I purchased a Maytag French Door Refrigerator in July 2011 from Lowes online and had it delivered on August 16, 2011. In September 2011, I could not get the ice maker to work. So I called Lowes and they called in a repairman. He came and replaced a part to fix the problem. I dont have any complaint with his work but here it is, October, and the ice maker makes maybe four ice cubes at a time on a good day.I am really disappointed with this product and according to their commercials, I would like to know which of these techs are setting around doing nothing, maybe he could come and fix my fridge once and for all. I would sure find it difficult to recommend any Maytag appliance as a result of this mess. I could call a repairman myself, but I was under the impression thats what a warranty was for. According to Lowes we are required to call them and they will schedule a repairman or the warranty isnt any good. I replaced a GE French Door with this Maytag, I sure am sorry I chose this Maytag.I know an ice maker problem is minor compared to some of the complaints on this appliance, but when you pay good money for a product you have every right to expect everything about it to work. Im just wondering where these appliances are actually made?

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

It washes extremely well. Its reliable. The wifey loves it and thats enough for me!!! I have had no major mechanical issues. Since 2012 we use it heavily and every other day. I would purchase same brand if need be but Im confident that would probably be in 2024.

Bought this Dishwasher two years ago. Control panel was working intermittently now it does not work. I am looking for anyone with this same problem. I know lawyers who are class action specialists who fight for the consumer. We need to make Maytag responsible for the flaws they have in their product. From reading these other reviews it seems that this control panel issue is consistent no matter what model you have. They must all share the same electrical components that is causing this issue with the control panel. My model number is MDB8959SBS2.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!