Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Washer is noisy and water does not saturate clothes on normal wash. Have to use sheet setting for small or large load. Washer changes gears and it is so loud and clanks like something is falling apart.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

Bought a Maytag Bravo washer, suppose to be the best of its kind from Home Depot. Should of known I was in trouble when it took them over four months to deliver it. It lasted two years before the bearing went on the machine. Whirlpool/Maytag was of no help. Ironically, the machine Im using today is my old Maytag I bought 17 years ago. The repair cost for the new machine was about 50% of the cost of the machine purchase.

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

I spoke to Destiny today at the Resolution Center, she knew one phrase, its a low usage washer. I would reply, 3 inches of water in a drum does not wash my familys clothes. Every load is covered in white soap specks, whether powder, liquid or pods are used. Again, Id hear, its a lower usage washer. Ok, I got it.The machine has been cleaned with Affresh.This washer cannot clean a single shirt let alone a full load of wash. Maytag (actually made by Whirlpool) should be ashamed to produce such a shoddy product and expect to the consumer to keep paying for repairs. From reading the reviews on a couple of websites, consumers have to keep repairing this washer time and time again. Destiny told me she would send a technician out at my expense. The machine will be in the landfill on Saturday. Never again Maytag/Whirlpool.

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

Come on people are you serious! Im talking about all those people who give this washer great reviews or even mediocre reviews. This washing machine sucks! Thank God for the glass lid so you can see how terrible it washes. No water in this thing. Clothes that sit on the edge of the bowl do not agitate enough to be washed if there was water in the wash cycle. Bleach that you use in your white wash cycle is left over and gets onto your colored cycle if you wash it the color cycle next. I ** you not, mark my words that stains are left on clothes even in a cycle that has lots of water in it. If you think Im high or crazy take a look at your local Home Depot or Lowes store. Check the area for washing machines that are for sale that have been used. You will find this Maytag Bravos XL machine there. They look good and are practically brand new and they will be there for weeks on and because people return them if they get lucky to return them. I called my store and they refuse to take it back and told me to call the manufacturer. I did just that... I called the manufacturer and they told me they can send out a serviceman to check the washing machine. Butt...and a big butt, if they find nothing wrong with the washing machine that I will be charged a service fee. Bunch of **! For all of us that get stuck with this pile of garbage we can thank the tree huggers for trying to save the world with low water consumption water washing machines.

I had a stackable Maytag dryer that was bought in 2016 but only used during the summer of 2017. Last May the dryer stopped heating. I contacted Maytag and they sent a repairman a week or so later. He identified the problem in the electronic control and ordered a replacement part. The part came and he installed it a week later. The part was faulty and he ordered a replacement for the replacement. It arrived a week later and also did not work. He said he had problems with replacement parts but contacted the technical service department at Maytag as he did the first time. The technical service person said there were problems associated with new software being not compatible with dryers in the last year and we needed a new control panel. I contacted Maytag again waiting the usual hour to get through on the phone. They agreed to replace the parts for free and ordered a control panel that arrived a week later. The technician installed both parts but they did not work. I contacted Maytag again and after waiting the required hour talked to a person who said she would contact the department who could arrange a replacement. They contacted me a few days later and said they would supply a replacement for $250. This was delivered a week or so later but they did not have a stacking kit and returned to the delivery company with the dryer. A week later they returned with the stacking kit but forgot the dryer. A week later they returned with both the dryer and stacking kit but the installer (always a different person) said he was too big to get in the space behind the dryer and that the venting supplied was wrong.I bought new venting from Home Depot and a new installer arrived a week later. He said the new venting was not necessary and in fact wrong and installed the dryer. It ran but foolishly I did not check to see if it heated and neither did the installers or if they did took off without letting me know that the dryer, like the one that was replaced did not heat. I discovered this a couple of days later when I tried to use it. I contacted Maytag and they setup an appointment for a new service technician to visit. I contacted Maytag again today hoping to get some explanation of what might happen next or some explanation. They had no idea but did inform me that they would not replace the new dryer but would start repairs again.

I own a Maytag dishwasher - it is a few years old now. I first filed a complaint in 2011. We have had it repaired several times - the control panel keeps breaking. Why is it that my grandmothers old dishwasher worked for 30-40 years and now you are lucky if you can get an appliance that works for a year without breaking? This planned obsolescence is ridiculous. Do not buy Maytag products - hit them where it hurts - in the wallet. They used to build quality products, but not anymore. I contacted the law firm in California that another person had listed as they have started a class action lawsuit. Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 - if you are having atrocious problems with your Maytag dishwasher (they mentioned Fridgidaire, too) - because of the control panel, please call. The company wont fix the issue unless they are forced to.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

In September 2008, I purchased a Maytag washing machine (Model MTW5700TQ0) that had a faulty transmission. The machine was immediately replaced. Three years later, the transmission is again faulty. Maytag has refused any responsibility for repair or replacement.

This is not a complaint but a love-letter. I know that todays Maytag Neptune is not the Maytag of old. But Im here to report that Im still using a Maytag washer that was built in 1982! The only thing wrong with my machine is that it occasionally goes off-balance when I wash heavy towels or blankets. Note: We inherited this machine with the purchase of a home in 1991. We were a family of 6, so this machine has done many heavy loads! Im looking forward to celebrating my Maytags 30th birthday, come Jan. 1, 2012. And I would love advice on how to replace it, eventually, with another machine that has just the basics - no bells and whistles, computerized control panels, etc.

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

I bought my Maytag Neptune washer and dryer in 08 or 09, and it has smelled like mold and mildew for years but I still have to use it because I cant afford to get a new one. I cant get the smell out. Also, I have to take the pump apart at least once a year due to the fact that sometimes, no matter how you check your pockets, change still gets left behind and they dont make a screen or filter that will keep the change out of the pump. It is not hard to do, but the first year I had it, it were in the service center as much as it was home. I was glad when someone told me what was happening because I fix it myself in like 15 minutes and move on. But it should come with a self service manual showing how to do this procedure to save people money.

Dishwasher Model #MDB7609AWW2 - I have replaced the touchpad once a year for 4 years. Went online and learned a DIY repair using a Permatex Rear Window Defogger Repair Kit to fill in the touchpad broken circuits. I have repaired it once a year for 2 years. My suggestion is to avoid purchasing this product. Apparently even after multiple consumers have contacted Maytag regarding this widespread defect, Maytag has not issued a recall or assisted anyone. They say if the part can be replaced there is no issue. When the dishwasher works, it is great, however it WILL NOT last. Touchpad will fail and you will be out $124 for the part plus labor unless you do the repair yourself.

We purchased a Maytag refrigerator model # MSF25D2EAS on 10-22-2012 at the Home Depot in Tracy, CA. On 2-2-2014 (15 months) we noticed a puddle on the kitchen floor. Upon inspection, we noticed that the refrigerator was not working. Went over to Home Depot and were given the name and number of the authorized Maytag repair dealer (A and E). The technician arrived on 2-5-2014 and replaced the compressor on-off /overload relay and charged $243.82. On 2-16-2014 (11 days later), the same thing happened again. The technician came on 2-19-2014. This time, it was the compressor at a cost of $800.00 plus the $75.00 service call. One can purchase the compressor online for $300.00 and I am sure that A and E buys it for a lot less. We thought about it and decided not to get it fixed because we did not know what else would go wrong and how long would the second compressor last. We talked to the Appliance Departments assistant manager and were told that Home Depot does not give any kind of consideration and she had worked there for 11 years and had not heard of any problems. She was not telling the truth or she was not aware of the numerous negative customer reviews online. She also informed me that I should have bought a warranty. We have bought quite a few refrigerators in 50 years and they lasted for many years. Home Depot sells inferior products. Maytag must sell these inferior products at discounted prices and of course, some stores are looking for larger profits. I do not trust Home Depot any longer and will not purchase appliances there anymore. It was a very expensive lesson - the price of the refrigerator, loss of food (twice) and the stress it caused. We bought a new refrigerator at Sears and it was not a MAYTAG.

I purchased this machine 6 months ago - have called 2 repair people. Thank God I purchased at Sears with extended warranty, was just replaced. I would tell you if you are looking for a machine run away from this one. It tears clothes, have to wash everything on bulk wash or I would not get enough water to say how bad this washer is. If someone called me and said I won this washer, I would say no thank you. And if I had to say Maytag repair called them, said she not getting enough water. Now this is what they told him: thats how we designed it. Forget about big drum, you cant put blankets or any larger items, goes off balance. And I have to say, if I had the money, I would put to the road and go back to wringer type. So again, do not make my mistake. Do not buy this washer and let me say the second day I made a complaint, was told it take time to get adjusted...NOT. I give this washer a 0.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

We purchased the Bravos XL Washer (top loader) and dryer about a year ago and have had issues with it since it was installed. Please note, we live between two homes so the machines are not heavily used at all. Our $250 machine we have in our Florida home works a million times better and is several years old. We purchased at the ABC appliance store and they have sent out a technician 4 times in the first few months. Bottom line, these are just pieces of crap machines. They cannot be returned! It is really a shame for the money spent and your clothes does not get clean on any cycle. The technician told us we should use the Deep water wash for all cycles which still does not work. I bought this machine for the XL capacity but also for the delicate cycle and stains do not come out, undergarments are still dirty, white power residue from OXI is left on the clothes etc... DO NOT BUY. This would get zero stars if I could. So disappointing and frustrating. If class action suit does happen, I would want to be part if it.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

Similar to dozens of others, we purchased a Maytag dishwasher from Home Depot in March 2011. Recently, it stopped working, dead - no lights, no action. Called Maytag and they referred me to a Maytag Repairman: Coastline Appliance Service of Huntington Beach, CA. The serviceman came out and spent 20 minutes, checked the door switch for continuity, and declared the control panel bad. How do you know its the control panel, I asked. Its my gut feel, based on experience, he said! He charged me $129 for the visit and said a new control panel would cost $380! After reading other posts online, I can only conclude that a new control panel (if that is, indeed, the problem) will also go bad in the next year or two. So, like so many others, were off to buy a new dishwasher - and we will never buy a Maytag or Whirlpool appliance again.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

The Maytag Neptune FAV6800AWW Washer has to be the crappiest product I have ever bought. I bought it brand new and hardly ever used it. The first time it broke it was luckily under warranty, although we had to pay for the repair man to install it. It took two new circuit boards before it was fixed. A few months later, the circuit board went again, and it was conveniently for Maytag now out of warranty. The repair man told us that their company never carried these washers because from the get go they had a ton of problems. He said that the odds of it breaking again were great and that we would be better off putting the money into a new washer.I dont understand how the company, in good conscience, could continue to sell a product to consumers that they knew was faulty. It was not a cheap washer and I have never been so disappointed in my life. You would think they would have had a mass recall or, knowing how many problems consumers were having with the product, offer so much money towards a new one.I laugh at the commercials where the Maytag man was bored because their product never broke I could have kept that man busy for months!

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

Bought a Maytag MVWX655DW top loader clothes washer from Best Buy on 7-7-2020 it was delivered as promised on Friday 7-10-2020. The people who delivered it were very professional and nice. They did a great job installing it. My wife went to use it for the first time Saturday morning 7-11-2020. Luckily this washer had a see through door. We could not believe our eyes, it never put enough water in the tub to cover the clothes. So as we watched the clothes on top never participated in the wash, they just moved around. When it went to spin cycle it was making a loud clicking sound as it was shaking. So we tried different settings, after 3 loads I called BB and said I want to return it. This machine has been mislabeled, its not a clothes washer, its a noise maker at best. DO NOT BUY THIS MACHINE. IT DOESNT WASH CLOTHES.

Bought brand new Maytag dishwasher. Worked great for 3 years. Then caught on fire. Couldnt contact maytag for a month because when you call your on hold for 30 minutes. Then when I do contact them they will only want to give 50%off another of their products that Ive already had catch on fire. I will never buy another one ever.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

First failed after 16 months. Second twice in 15 months. They are lucky to last 16-24 months. Stupid for a microwave that normally last 5 plus years for every other brand I ever bought.

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

Do not purchase this microwave! I checked the reviews and thought they couldnt all have the same problem. THEY DO! This Maytag Microwave MMV4205DS1 has some faulty switch in the door latch mechanism. The warranty repair company came and adjusted the switches... and then fully replaced the switches. Each time it worked for about 30-60 days and then the same error would repeat itself. Never resolved... buying a different microwave. Be sure to check all reviews for repetitive complaints.This microwave will NOT function AT ALL with the door open/close message. Here are the details of our microwave. Purchased from Home Depot December 2015. First experienced the open/close door message around June 2016 (6 months after purchase). With the open/close door message, the interior light will not come on, the keypad will accept entries but will give the open/close door message as soon as start is pressed. Repaired under warranty August 2016. Repairman tightened and replaced one of the two fuses behind the metal plate. Also moved the door connectors as far as they would go to help with the door sensor issue. Worked until mid-December. Same message reappeared. Called repair company. Still under warranty. He order new switch parts and installed in January 2017. Microwave worked for 2 months. Then same exact door/open close message. Called repair company. Since we do not have an extended warranty, the parts would be covered but not the labor. DO NOT PURCHASE THIS MICROWAVE or any other microwave that has reviews listing a door open/close issue. It will not go away! ...and you will be very frustrated.

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

For years I wanted a top loading Maytag washer. Last year I bought one at the cost of £720 plus VAT. Started using it last July and in November this year it broke down. The company I bought it from said, Sorry, youre out of our warranty... Really! Here’s some people who might fix it. Eventually Hotpoint took it on and honored a two year warranty. Since November I’ve had an engineer out twice. Still isn’t working. Won’t replace it because it’s now discontinued, so more parts ordered. Engineer advised me to go buy another washer. Thanks Maytag for totally disappointing me in what I thought would be my perfect washer. I will continue to email etc and hope that someone will help me. No point in phoning because no one listens. MY OPINION - DONT BUY AMERICAN PRODUCTS IN THE UK AS NO ONE CAN REPAIR THEM PROMPTLY IF AT ALL.

I purchased a Bravo 300 MVWB400VQ in 2009. I knew in 6 months that I had made a huge mistake. The clothes began coming out soaking wet - the dark clothes have lint, pet hair, and rings on them. The large capacity drum is just that... a big drum. If I wash bedding in it, it becomes off balance and sounds like its fallen over. I have used only HE detergents, and I wash the washer (yes, wash the washer, does that tell you anything?) before the light comes on. Now the machine sounds like its full of loose parts or rocks in it when it begins to fill up. Its even worse when the water starts to pump out. Now that Ive read all the other complaints, I realize that Im doomed. All of these trusting people have been cheated out of nearly a thousand dollars for a piece of junk. What good is Consumer Affairs if there is nothing done when there are so many complaints? I will join any lawsuit against Maytag if ever there is one. This is another lemon that promised everything and delivered nothing.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

Ice maker stopped making ice within first month. Repair man came out next day. Said ice maker only makes 7 cubes at a time 8 times a day. REALLY? A $2000 refrigerator only makes 50 ice cubes a day??? Why would I need a refrigerator that size if there was only one of me? Obviously, Ill be keeping a bag of ice nearby.

We purchased the Maytag double oven 30 inch 5 burner, stainless steel, model MGT8885XS. Oven worked good for six weeks. The igniter broke in the bottom oven and when the third party non-Maytag repairman came out to fix it, he was unable to remove the bottom oven door. It is not flush and heat escapes when the bottom oven is on and it causes the top oven to get condensation. The repair man was directed from a technician from Whirlpool that he had to order a new seal and hinges. I dont want it fixed. I want a new one. I have called Customer Service for Whirlpool and the third party and the store in which I bought it from and everyone is pushing it off onto someone else. Customer service is poor and stated they will only fix the oven and will not send us a new oven. We sent our rebate in the mail which was to arrive within 8 weeks and we have yet to receive it. Very poor customer service. Glad I purchased the 4 year warranty. I will never buy Maytag again.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

Have had this problem since week 2 of ownership. Even on the lowest setting, food in the fridge section is freezing and Im having to throw out fresh produce weekly. Called Whirlpool service since under warranty. The very nice service man replaced the thermostat. Only a little bit better as the temps do not range quite as extreme - only 25-46 now! I am now waiting once more for a service appointment, at least 10 days. Plus in Massachusetts they will only give you a 8-5 service window. They give a robocall the night before and you are given a 8-12 or a 1-4 time for your appointment. I also have had trouble with the meat drawer falling out of the track because the upper shelf bows with the weight of a normal amount of stuff. Now the bracket has cracked and the meat drawer no longer stays on the track when it pulled out partially (such as when you need to reach in and get something). Same thing happens with the lower drawer on the right side although the bracket hasnt cracked.

Such a horrible and expensive kitchen purchase. The stainless looking pieces are either fake or very poor quality - they scratch so easily. After the first year of use the top of the stove looked like it was 30 years old. The oven glass is extremely hard to get at to clean - you have to remove very finicky screws that dont go back into place easily. Oven temp is questionable and it takes a very long time to heat up. I would never recommend the Maytag Gemini oven to anyone.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

Purchased Maytag dishwasher model # MDBH979SAM1 on February 8, 2014. 6 months in paint came off door. Added 5 year extended warranty on 4/21/2015. Dishwasher started not working properly on 9/24/2015. Hit one button but a different would light up until finally on 10/2/2015 it quit working. Called for service On 10/2/2015 10:30 pm no answer. Tried again on 10/3/15 same answer. Tried again on 10-5-15 finally answered and they called repairman. No answer but they gave me his number so I could call him if he didnt call. Finally called him and He told me he was busy and could not come repair my dishwasher. I called MaytagNed they said he would come. When I called he said he was not coming. He had truck trouble. 10-12-15 Called Maytag back and they said they would find another repairman. They would call me back. Into 2 weeks waiting on appointment. I will never buy Maytag again. It didnt clean dishes good when it did work!

First bought a nice looking Samsung. Didn’t last 6 months. Upgraded to a nice Maytag with steam and have never regretted it. It’s been years of worry free and trouble free use. My Samsung dryer is on the way out the door and to be replaced with a Maytag too.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

We moved into our first house just over two years ago and decided we needed to get a new refrigerator. We did a ton of research online, reading reviews, etc. We found a few not so great complaints regarding Maytag; however, we took our chances. (Note that we live in a house built in the 40s, so the fridge space is small and we needed a fridge size that is smaller than normal. We didnt have many options.) Well, a little less than 12 months later (yes, luckily right before the warranty expired) our ice dispenser stopped working properly. The mini-ice door would not close properly, resulting in a lot of frost in where the ice door was located. (There was so much we couldnt open the freezer door. It would get stuck.) So, we called out the repair guy and he said he had never seen this issue before and basically had to replace the whole flap and parts. Sweet. It was fixed and cost was covered! Well, about 5 months later, it happened again! Ah, they got it fixed yet again. Well, another six months later and after the warranty expired (lucky us), the fridge completely stopped cooling. (And it just happened to be Halloween, not a great day for a house issue.) So, we had to remove all our perishable food and place it in a cooler (which works hundred times better than Maytag products), and move all frozen food to a family members house 15 minutes away (luckily!). We were also super lucky we found a repair company that could come out at 5pm the next day, which happened to be a Friday! Awesome company (Conners Repair in Metro-Detroit). He concluded the defrost board was broken, meaning it was freezing and creating frost and then not defrosting, clogs the vents and not allowing circulation to occur. He was shocked when he found out we only had this fridge for 2 years and said this is something that normally happens in 20-year old fridges. I then decided to call Maytag and nicely requested a refund for the issue. I was told no due to the warranty expiring and also because we didnt use a Maytag repair company. I didnt want to wait a week as I thought this was something that needed immediate attention. I also am not sure why it matters who you get to fix your fridge. I have an invoice for proof of the issue and the repairman even said hed call to verify the issue. I don’t understand why I have to pay for something that was not properly produced, and not to mention the time out of my schedule to deal with Maytags issues. I now know not to buy any Maytag products due to the lack quality. I guess I learned the hard way.

Purchased Maytag 3000 series washer and dryer in June 2009. Like many other reviews, the washer is making a terrible loud noise during the spin cycle. I contacted Maytag customer service and was told wait time is 10 minutes and opted for the call back option. Received a call back from an agent located in Tennessee, United States and he checked for recalls or projects and found nothing. Offered a technician call in my area for $112.00 for 30 minutes to diagnose the problem. I told him that if he checked on the reviews, he will see many regarding this problem and a bearing issue at a cost of up to $700.00. The Maytag repairman is not only lonely but out of business and Whirlpool bought them out. I would never again purchase Maytag or Whirlpool products. We are seniors and do not abuse our appliances and why do they not last at least 15 years. Talk about disposal washer machines, who can afford to purchase them every few years. The washer sounds like a jet going through our house when it is in the spin cycle.

Maytag top loader washer will not complete cycles. Washer is only fourteen months old. Repairman says parts will cost four hundred and seventy four dollars - almost what I paid for the washer.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

I bought this machine because it has a (deep water wash), which means there is a lot of water, enough to cover the clothes, at least I thought so, the salesman seemed to think so as well! But no, it does not come close to covering the clothes, false advertising! I must put my clothes in a large bucket, soak the clothes with water, then bring the bucket to the washer and empty it into it, because of the weight of the water, the machine adds almost enough water to cover the clothes.Another big problem with this washer is the fact that if I lift the top in mid-wash, while I do something, not wanting to listen to the irritating sound it makes in my apartment, after 10 minutes it starts to drain and there is no way to stop it, I must wait until it completely drains and restart the machine. This machine has the stench of government on it!!! My advice, keep your old machine.

My husband bought me a Maytag washer as a surprise gift. I was so excited to get a Maytag. I will never purchase a Maytag again. I am so tired of washing, rewashing and rerinsing my clothes and still not getting the soap out. I have used every different kind of detergent and used with and without fabric softener. I have also tried cold, warm and hot water. I would rather use more water and get the soap out instead of using more electricity to keep rewashing my clothes and then in the end having to take a wet cloth to get the soap out. Never had to do this with any other washer I owned. Very disappointed as I always thought Maytag was the best.

Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I paid $550.00 for this item, wanted to get a nicer one hoping it would last. Of course they only have a year guarantee for parts and Labor. Will not buy another Maytag appliance again!!!

I thought I was safe in buying Maytag for all of my appliances in my new kitchen. I bought a double wall oven Maytag MEW6630DDS. I bought it in late 2010 and have had no issues until August of 2018. I rarely use the bottom but used it in August of this year to cook cupcakes. After baking them and leaving the kitchen for a short while I heard a loud explosive, shattering sound. I walked to the kitchen to see that the bottom oven door had shattered into a million pieces. Thank the good Lord that I was not near it. I contacted Maytag to see if there was a reason it would have done this. They said that there had not been a recall. They sent a repairman at no cost to look at it. He came, took it apart and had no reason for why it would have done this. He left it in pieces and said that he was ordering the replacement door. Maytag advised us to turn off the breaker to the oven. After a month without ovens, the repairman called and said that the part had been discontinued. HA! You think?!? It has the potential to explode. It should have been recalled, not just discontinued. Maytag offered us 20% off a new set of $3000 wall ovens or $150 to pick ours up for disposal. Talk about saving the company money and screwing over the unlucky recipient of a defective product. They ought to be ashamed. I am going to have to replace the broken glass with aftermarket glass. What is going to happen when I use the self cleaning option? What happens when the top door explodes. I am scared to use my very expensive wall ovens that I thought would last at least 10 years. Shaneka at Whirlpool said that people have appliances fail all the time and just have to buy replacements. Do all of them have to replace ovens because doors explode for no reason? I am not the only one this has happened to. I have found several other complaints of this on the internet. Why did they discontinue these door? I wonder.

We trusted the Maytag name to give us a good product that would last. After six weeks the Maytag Bravo stopped working. Having to wait 7 days before a service repair person came to our home. The main motherboard needs replaced. So currently, we are still waiting for the part to arrive and have it installed. 2 weeks without a washer after spending 600.00 for a new washer. There is more problems also, this machine takes 1 hour to complete a single load of laundry. Plus it does not get the clothes clean and the rinse cycle does not get all the soap out of the clothes. Very unhappy with the Maytag Commercial Bravo. Will not buy another Maytag product. Save your money and get another brand. We plan to get this one fix and sell it.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

Maytag washer leaves clothes more wrinkled after a wash than they were in before being cleaned. And these are not full laundry loads. Then using the Maytag dryer is a joke. Need to run double times or extended times on most of the settings to get them completely dry. When it comes to the wrinkle free setting... what a joke. Clothes might be close to dry but wrinkled. Have always had Maytag products since forever. Tried Samsung for the last set-----washer lasted 6 years and then needed a full overhaul. Cheaper to buy a new set. Went back to Maytag. MISTAKE. Samsung did a lot better job of washing and drying. Now stuck with Maytag until... when? Retired and dont have the funds to get new replacements. Just my opinion though.

I really like the refrigerator. Its easy to maneuver and frost-free, but I should have gotten the side by side. Also, make sure of your family size before you make final decision. Other than the size I would recommend to family and friends to purchase.

The dishwasher is very stylish and looks great in our kitchen. I do wish there was a small knife drawer in top. It cleans very well and is super quiet. I would highly recommend this dishwasher, good value.

We had our kitchen redone by Home Depot in Sept. 2006. It was gutted and all was replaced: walls, heat windows, doors, lights, appliances. The Maytag refrigerator stopped working 7 years later. I feel an expensive appliance should last longer than that.

Things that I have read that are true: Rips clothes/towels/sheets. No real problems with motherboard like some have stated. Bought Maytag Bravos Washer/Dryer in 2009. No real problems with the dryer, HOWEVER, may with the Washer. Had the pump go out in 2/2010 to the tune of $199.20 due to a small object in the pump. The repairman said it would just take a very inexpensive part from Maytag to prevent this. In 6/2012 washer not draining, clogged pump. All right, new to HE Washers, so told to use less detergent than detergent manufacturer recommends. $79.13 to fix clogged drain. Even though being careful with items in pockets, loose buttons, etc. AGAIN had pump go in 1/13, $214.22 (same problem cheaper in 2010, repair inflation). Wed noticed it was loud on the spin cycle (like a rocket going off) and were told at that visit the bearings would need to be replaced, and quoted approximately $280 to repair those. Havent fixed, waiting for something else to go wrong and then decide what to do with it. So in 4 years paying almost the purchase price of the unit (if I fixed bearings also). Crazy. If you bought a house and had to pay 4/5 of the house to repair it in that short of a time, no one would own a house!!!

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

My Maytag Neptune washer was purchased last October 2010. In the past few months, the washer has been making a loud noise when spinning/washing. I had a Maytag repairman look at the washer, and all the barring, etc. needed to be replaced, which would have a cost of over $450.00! I am very upset with this outcome and just looked into it and found that this washer had recalls that the consumers were not properly notified about. The lack of recall communication is inexcusable, especially since I even went as far as to buy a 3-year extended warranty and still was not notified.What really set this situation was that the repairman suggested to not buy a Maytag washer and he added that it would not be a problem since Maytag has been purchased by Whirlpool and that the Neptune washer played a part of the ending of Maytag! This whole situation has really put a bad taste for any Maytag product, and all of my major appliances are Maytag as well as the dryer I just purchased a week ago, before I knew about all of the disappointment of Maytag. I am sure the response I will be getting will be as good as the notification of the recall, which will be nothing. Thanks!

Worst washer ever. My clothes I have to wash a few times before they all get wet. Not a good washer at all. Has all the bells and whistles. Lets me know when the washer is done or its unbalanced... my washer is crap. Ive had it maybe a year now. I now have to buy another one. Why? Because this one sucks literally... its Maytag commercial technology.

Ive had my Maytag (above range model) for about 4 months. The same as everyone else with open/close door error. Faulty door switch. When the interior light doesnt come on, I know I will get the error. You would think Maytag would have already repaired or replaced this door switch part.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

Wish I would have read the many, many, many reviews on the Maytag MDB8959SBS dishwasher before buying it. As noted by others, the touch control buttons stopped working 1 month after the 1 year warranty expired and Maytag wont do anything about it. BE WARY OF THE 10 YEAR WARRANTY CLAIM - IT DOESNT COVER THIS PROBLEM. Maytag should issue a recall on this product and do the right thing - take care of customers like they used to.

After writing a polite but stern complaint to several of the executives at Maytag and Whirlpool we got a call from their executive assistant. She arranged to have a technician come out to our house and assess the installation. He found nothing wrong and Maytag replaced the control panel for free. The technician has seen numerous faulty electronic control panels, and not just with Maytag. He would not recommend a preferred make or model. He longed for the old mechanical timer switches, which we could no longer find in the newer models. With enough customer complaints maybe they will do something about the electronic control panel in the future.

Bought mdb7609aww2 dishwasher in 2010. Now I cant use it as it will not start even though the panel lights of my selected wash cycle work. I looked up on internet how to reset it, but I only get a half cycle. Called customer service and for $269, I can get it fixed and get a one-year warranty. Wow, what a deal. Might as well get a new dishwasher. Joining the lawsuit. It is about time corporations take responsibility for defective merchandise, not make money to correct their mistakes by charging customers for overpriced parts and stupid worthless warranties. A pox on them.

Two and a half years ago I bought a Maytag dishwasher thinking it was time to upgrade from my Ge. After a year and a half the control panel went out in in it! So For a little over a $100 I replaced it. Now, a year later, the panel has gone out again!!!! What is this? Every year I have to spend over a $100 to repair this thing!! I think it is time to find a new dishwasher!

Recently started having puddles of water on floor every morning. Just noticed a thick sheet of ice on freezer floor when I had trouble closing the freezer door. Also the water dispenses very slowly. Removed filter and it would not dispense at all. Will try melting the sheet of ice to see if that helps. Purchased 2011.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

I bought the Maytag Centennial Washer a year ago. I have had nothing but problems. The clothes never get fully wet so you have to wash clothes 2 or 3 times. The lid does not open when running. So you cant put soap after the clothes are damp. I say damp because they dont get wet. Right now the sensing light has been on for 2 hours. I need to catch a flight in the morning and I cannot wash my clothes! My white clothes never get clean. I have to wash 2 or 3 times. Actually 4 time would work better. The water and electric wasted with washing over and over again is nuts. Stay away. Ive warned you!

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

Just bought a washer and my clothes are always left with dust and dirt on them after washing. Called Maytag, they sent a technician over, but he found nothing wrong. Company refuses to do anything about it, including exchanging it for a different model, since weve had it for more than a month. I am extremely dissatisfied since I just lost over a grand on a washer that doesnt actually wash my clothes.

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.