Bought a Maytag front load washer. When it is operating it is very loud. Some parts of the washer are made of cheap plastic. The Optimum detergent dispenser also of cheap plastic failed after 1 month. Disappointed in finding out only the outside metal box was made in America. All inside components are made in China which raised the cost $300 due to recent tariffs.

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

We have had a Maytag Bravos washer for a while, which has a see-through top load lid and a very small or low agitator. I have to say that I really miss the old fashioned agitator which makes all the clothes being dragged underwater and scrubbed well. We have watched the loads being washed in this washer many times and the clothes are not being swished around very effectively. You feel like you need to help it getting the clothes washed as it seem like it just sit in the same place throughout the cycle. The clothes ends up in big knots around the edges, and you can see the same towel sitting on the top during the 2-minute rinse cycle, never getting completely under water. During the wash cycle, the lid gets locked, so you are not able to open it up to untangle or move towels around if it has gotten unevenly distributed. The wash cycle is very quick, so all in all, Im not sure how clean the laundry really is when its done. We will never buy this kind of washer again.

I bought all new Maytag appliances for a new house built 2 years ago. The oven fan, while in warranty, began coming on in the middle of the night. It would turn on, cancel, began not working, and then the ticking noise began. Maytag sent 5 different service people out, sometimes without the part. We are afraid to use it now and have turned off the breaker for it. Now, it is turning itself back on again. Maytag says we must now pay for any repairs/service calls as it is out of warranty. It was not out of warranty when all these troubles began.I called Maytag customer service today and could not have talked to a less customer friendly person. She didnt care that it was in warranty when the trouble began. It is out now and is our problem. There is no one else but her we can talk to about it. She is the decision maker. What experiences has anyone had with trying to call the president of Whirlpool, or filing a small claims court action? Any help is appreciated. Who is going to cook our Thanksgiving turkey?

Bought this machine with the intention of having at LEAST 10 problem free years with it. Its a Maytag after all. Not an unreasonable expectation. Within the first 2 years, the machine sounded like the bearings were going out (heavy, grinding noises when it shifted gears). Repairman came, replaced the entire drum (only way to get to the gears, I guess). Didnt fix a thing. Then the rinse and spin cycle on ANY wash cycle randomly quits. Just stops. Full load of wet, soapy clothes, sitting in the tub while an LD error code quietly flashes.Its not uncommon for it to take two full days of screwing around with this machine to get one load of clothes done. Have to UNPLUG the machine, let it sit for about an hour, and try again. It is the biggest waste of money ever and I will NEVER buy another Maytag nothing. Contacted Maytag and they recommended I call a repairman...REALLY? REALLY? Gee, I wish I had thought of that. Repair guy has been to my house so damn many times for this machine, we are now friends on Facebook. Dont waste your money on this machine.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

I purchased a Maytag Bravos HE top loading washing machine two years ago. The clothes hardly get wet enough to get clean. It leaves a residue on dark clothes and the basket goes unbalanced at the drop of a hat. Whatever you save in water, you spend on electricity because a cycle takes twice as long as a conventional washer. It goes out of balance and bangs the machine enough to walk it across a room. I purchased this machine from an appliance store, not some discount house. I have had machines last 20 years and this one is shot in 2. I will never, ever purchase another Maytag, Whirlpool or KitchenAid product again ever.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

We bought our Legacy Washer and Dryer from Home Depot in December, 2005. Luckily we also bought the one year warranty, because in January 2006, our washer quit running. We called Home Depot, we got the runaround and I think Maytag sent someone out. When he tipped the washing machine over, a belt was off. He said it happens. The next year, something else went wrong with the washing machine (not under warranty anymore) and I paid $129 for that visit. Three weeks ago, the spin dry quit doing a good job on the extended spin cycle. Tonight, I put a load of clothes in and though the washer sounded like it was agitating the clothes, when I lifted the top I saw it was just noise, no agitating. I cannot afford the service call, let alone the whole repair or a new washer.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

Internet stated refrigerators should last a minimum of 13 yrs and up. Mine is less than 5 yrs. old, a Maytag 25 cu. ft. French Door Bottom Mount Ref. with freezer on the bottom (MFF2558VEW). Had to replace upper gasket in less than 1 yr. of purchase and needs another now (not affecting the sealing aspect on doors, more aesthetic on upper door thin flap that tears easily).Drain plug & configuration for drain was a known manufacturers defect, but cost me money to replace as 3 yr. extended warranty expired. Lower gasket had to be replaced in yr. 4 of ownership, bottom of freezer was producing a sheet of ice that needed removal every week. Normal settings is #3 for both top and bottom, worked fine for 4 yrs at this setting.Last month irregular cooling started to occur- top down to 52 degrees and bottom freezer below -20 degrees - ice cream hard as rock, have to defrost each time in microwave. Maytag repairman said could find nothing wrong, but try emptying entire contents and unplug for 24 hrs. I could hear pieces of ice melting and dropping throughout the evening. Next morning towels I had put around frig were saturated with water. Restarted frig after 24 hrs. and was working fine for 5 wks.This week same exact problem returned so I did the same thing only this time I had to go out and buy a small chest freezer as I had a full one in my Maytag and no place to put frozen food. It is nearing 24 hrs. and no water has appeared on the floor nor did I hear any ice melting and dropping - so dont know what to do. Will call repair man again and see what he suggests. As soon as I can afford another $1400 frig (this was on sale for $1,002 after discounts, but I will buy a less expensive one this time) I will purchase another brand with NO French doors and no bottom freezer. I loved my frig the first 3 yrs. under warranty, but now causing me too much physical problems having to empty and restock frig for repairs. I have a Tappan Frigidaire in the garage that is from 1998 - I bought from a neighbor who was moving and it has been working fine for 16 yrs. with no repairs. They dont make them like they used to!

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

I purchased this machine 6 months ago - have called 2 repair people. Thank God I purchased at Sears with extended warranty, was just replaced. I would tell you if you are looking for a machine run away from this one. It tears clothes, have to wash everything on bulk wash or I would not get enough water to say how bad this washer is. If someone called me and said I won this washer, I would say no thank you. And if I had to say Maytag repair called them, said she not getting enough water. Now this is what they told him: thats how we designed it. Forget about big drum, you cant put blankets or any larger items, goes off balance. And I have to say, if I had the money, I would put to the road and go back to wringer type. So again, do not make my mistake. Do not buy this washer and let me say the second day I made a complaint, was told it take time to get adjusted...NOT. I give this washer a 0.

I purchased a new washer and dryer from Lowes a few months ago. I had my former washer and dryer for nearly 20 years and although the dryer started to have some issues, the washer worked wonderfully. To have a matching set, I decided to purchase both a new washer and dryer. I was told the Maytag Bravos XL model was the top of the line and could handle large loads. After just a few washes I realized this machine does not add enough water to get the top clothes wet and there is no agitator to pull the clothes into the water. I returned to Lowes and was told to use the deep water wash. I tried that and still had clothes coming out from the wash still dry and dirty. Unfortunately Lowes would not take the machines back and I was told to call Maytag. Maytag said there was nothing they could do except send out a technician for a service fee of $98 to help me determine if the machine is functioning correctly. I could not dislike a washer and dryer more! The dryer catches clothes on one of the screws inside and pulls fabric pieces out. This is in my opinion the worst washer dryer set I could imagine having. I will share my experience with as many people as I can to help others avoid making the costly mistake of purchasing a Maytag product. Maytag does not seem to care they have designed and sold a dysfunctional product!

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

Food freezes in the refrigerator. If I turn it down, the freezer does not freeze. What has happened to the quality of Maytag? This unit is so new. I think I am going to take it back and buy a better brand!

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

When I attempted to contact Maytag about an issue in my 3 month old washer all I received is an automated email back saying to contact one of the repair places on their website. There was one, so I notified Maytag I would contact them. I contacted them. They said Maytag had not notified them that this was a warranty repair and if I wanted them to come out I would have to pay for it. I have attempted to contact Maytag several times to get this straight. Guess they are trying to wait out the warranty to respond. Will NOT EVER buy another Maytag. Too bad they used to be a good product.

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

Do not buy this refrigerator!! It’s small on the inside but to top it off the vent is on the left side, not in the back, so everything freezes on the left side of the refrigerator. Plus they positioned the light right in the front at the top so you cannot put a gallon of milk or anything tall. Not orange juice, apple juice, nothing!! Horrible design. I’ve had the repairman out, he said he couldn’t do anything about the freezing on the left side unless he turned the temperature up on the fridge and on the freezer. We tried that & The ice cream was so soft, almost melted. The problem then was the temperature was too warm for milk and other items. Not a recommended temperature to keep cold items. He said I would have to keep everything away from the back & the left side to use it without freezing my items. I’ve lost a lot of food because of this. Very unhappy with this refrigerator!!

We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Just a couple of issues I would like to bring to your attention before you purchase your Maytag. The single refrigerator door does not close automatically. You have to close the door. The metal handle is metal and has a metal smell and feel to it. The stainless steel door and the handles are not the same finish. Although this might not be a problem for some who like the industrial look I prefer my hands to be free of chemicals while I am preparing food. The ice maker takes up too much room. The ice maker should have been an option, not a standard item. I had a Kitchen Aid for 10 years and loved it. I thought I was going to have my Kitchen Aid for 15 years or more. I would have purchased another Kitchen Aid, but the reviews were not good.

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

We bought a Maytag Bravos three and a half years ago. We always tried to follow instructions for the machine. Only used he detergent, used the affresh, tried not to overload the machine etc. Had to call a repairman. Our washing machine started leaking water at the bottom. Hoping that it is only a three machine it would be fixable. Bad news the repairs would be over $600.00. It needs a new tub seal and bearings. For a THREE YEAR OLD washing machine! The repairman and I had quite a talk about appliances. He said they just dont make them to last anymore and the companies such as Whirlpool, Maytag, etc. do on purpose and they get away with it. Stay away from Maytag Bravos. It is a worthless piece of crap. It will not last long. Now we have a three year old washing machine that does NOT work right. Something has to be done in this country to come down hard on the companies that make appliances. I would NOT recommend this piece of crap of a washing machine.

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

We purchased our home five years ago. We bought a new Maytag oven and fridge/freezer. Within one year, the oven control went out. Then a few months later, the heating element went out. Within two years, our fridge/freezer went out. I purchased Maytag products because of the commercial where the Maytag repairman is doing nothing. I will never purchase a Maytag product again.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

Purchased 6-1/2 years ago when we had kitchen remodeled. Bought the stainless steel with stainless interior. The interior design was perfect for placing the various dishes, glassware and utensils. There are a number of settings to choose from, however, we tend to use it as more of a sanitizer so the light or normal wash are the preferred and dont use the heat-dry as we dont find it necessary. Very pleased with the quietness of the cycles and have no regrets with our purchase.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

I am submitting this review today to express my disappointment with my Maytag washer. This is the Maytag MVWX655DW (Bravo), with Serial# C61842055. In August of 2016 I lost many treasured items due to a flood in Lafayette, Louisiana. My daughter and I were devastated and displaced because of this event. This is also in addition to completing Cancer treatment 2 days before the flood.I lost my GE washer which was a great product. It was a struggle for a long time, but we were finally get back on our feet. I was able to get another place to live, and it was time to purchase a washer. I was told that Maytag was one of the best products on the market, so I decided to purchase my first Maytag washer. This did not turn out well for me, and it was very disappointing. After 9 months of ownership of this product, it is broken! It is my belief that the product may have been defective.I put in a service call, and had a repairman come to my apartment on June 19th. I was told that my washer needs several parts to repair it, including a pump. I have never had this issue with prior washers. My previous washer before my GE purchase survived for over 10 years before it has had any issues. I called on June 26th to ask about Maytag issuing me a new washer or a full refund, instead of repairing this faulty product. I was told no, and was offered and extended warranty for 6 more months and $75.00. I expressed to her that I would rather have a new washer.The Bravo Washer is a very bad product. Instead of taking advantage of customers, Maytag needs to stand by that 10 year warranty sticker on the washer. Please understand this purchase is a LEMON. This washer did not last a year. After all I have been through, I did not need this financial hardship. In the long run, this product will die again. Unfortunately for me I may not be able to afford to purchase another washer. I am still getting follow-up treatment for my Cancer, and it is very expensive. Can someone please re-evaluate the need for a replacement washer or offer me a full refund? This product should not be broken after only 9 months of service.

We Purchased a Maytag gas oven/stove three years ago believing it to be the quality of the Maytag of yesteryear, Boy have we been disappointed! When Whirlpool Corp. bought out Maytag several years ago they continued using the Maytag name only.. The quality is now less than substandard, It is a cheaply built piece of crap.. We would sell it in a garage sale and replace it with a quality stove/oven but we dont want anyone else to have to deal with this piece of junk! It will soon go to the landfill!!!

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

In August of 2009, we had an opportunity to remodel our kitchen plus add new windows and doors. How exciting! SO we had put down new flooring in our kitchen that matched our oak cabinets and since we had a little money saved, we wanted to purchase new appliances to match. We purchased a Maytag side by side with ice and water in the door. It also had the fingerprint resistant stuff on the outside. It cost about $1300. You buy name brand so they will last a while but here we are November 12, 2014, 7 years later and the compressor goes out. If repaired, it will cost $8090 to fix. Why do I want another Maytag. I got a citation I bought in 1978 and it still runs. Hello Facebook, you will my next visitor.

I have a 50/50 chance of completing a wash cycle. Most times, the washer stops working at 8 minutes remaining in ANY cycle. The washer will leave me with wet clothing and refuses to spin even when most wet, dripping articles are removed. I have tried to put all light-weight items together and that still is not a guarantee that I can get this done in one cycle. Most often, the error code comes up, I spin the drum around, move the clothing around and try again. This process is NOT energy efficient which is why I bought the ** thing in the first place. I am ready to put it on the curb for the trash man to pick up.We had a service person out and he said it is either the bearings or the motor (both a $400 job). I will NEVER buy another front-loading washing machine. At least with the old-fashioned top loaders you can get the load balanced and at least get clothing to go through the spin cycle. I am now hand-wringing clothing once again since the machine tells me when it will spin my clothing. That stupid chime is about to send me out of my mind!

I really like the refrigerator. Its easy to maneuver and frost-free, but I should have gotten the side by side. Also, make sure of your family size before you make final decision. Other than the size I would recommend to family and friends to purchase.

Due to our previous washer breaking down, we had to purchase a new washer. We have always been loyal to Maytag since we were always pleased and satisfied with the performance. However, this new washer does not deliver in performance, cleanliness, energy savings when cycles take much longer and you end up maybe not using as much water, but our electric bill has gone up considerably. I have nothing good to report about this washer. We purchased it back in April of 2013, and Ive given it the benefit of the doubt by experimenting with all the different wash cycles. I am just not happy with it. I so want to trade it in for a front loader and give Maytag one more chance.

Our Maytag dishwasher was just past the 1-year mark when the control panel stopped working. A certified Maytag repair service came out to diagnose just that and charged us $89. Maytag sent the user interface out to us, and my husband noted that there was absolutely no way that the part could be installed wrong. The wires could only go one way. The repair service (DSM Appliance Service) wanted another $120 to install it. We installed it, and it still doesnt work. Maytag will no longer assist us in any way. I will never buy a Maytag or Whirlpool appliance again. After investigating, I see that this control panel issue has happened many, many times; and I wonder why there hasnt been something done about it.

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.

This is the WORSE POS I have ever owned/used/etc.... our clothes are dirty, w/ a scummy film, really bad in most cases. Some have weird stain appear that werent there. Electric & water bills up. Have to always use deep water wash, double rinse. My clothes are wet when I put them in due to sensor fill (extra weight), also a zillion mesh bags. Clothes are getting trashed, faded so bad & smell bad. Having to use a cleansing product monthly, in one aspect, should encourage the engineers that signed off on this POS to change careers. Maytag customer service says no complaints have been filed!!! Horse **!!! $ 800.00, trashed, unclean, wrinkled to the point of almost needing to iron all your clothes. I have been going to the laundromat. Engineers should have been FORCED to use this machine at least 2 months.... good reviews my **.

I have Maytag refrigerator that is only 2 years & 9 months old that I am told by a service tech that it has a sealed system leak. So the unit runs it just wont get cold. I have lost all the food that was in the refrigerator & freezer and I told by Maytag that its not covered under warranty. The tech gave me a ball park quote of $600.00- $700.00 to repair the unit & I lost at lest $200.00 or more in food. I cant believe a new refrigerator wont even last 3 years & they wont fix their problem. So much for buying American made products. Whirlpool YOU SUCK & SHOULD BE ASHAMED!!!

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

We purchased a Maytag dishwasher (model mdb4709aww1) from our local appliance store. A little over one year after purchase, the control panel (part w10254834) stopped working. Our appliance store replaced it. They charged us for the part but not for a service call. Its been two years since the new control panel was replaced and it just stopped working. Now, we have to pay $275.00 for the new part and service call. My previous dishwasher lasted twenty years and we never had a problem. I thought Maytag was a quality product. Sadly mistaken!!

Very poor quality. Vegetables freeze at the back of the fridge I have tried everything. The vegetable drawer constantly comes off its track and the freezer door slide jams and stops the door from closing. It leaves about 1/2 inch gap. Now the Whirlpool/Maytag company changed their corporate policy and wont allow an appliance store that to come out and fix the fridge I have to go back to the manufacturer. Their website wouldnt take my email address when I tried to sign up for an account and they wont answer the phone. What a hassle. Ill buy another brand next time but never GE or Whirlpool again!

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

I have had KitchenAid and Whirlpool my whole life - lots of them - NEVER EVER have I had so much trouble with a washer. This front loader is the worst possible machine. My former Whirlpool was a front loader too - Never a problem. I purchased this Maytag set simply to have a matched set because our Whirlpool dryer died. This washer has to be babysat. The washer holds water and it gets musty - never ever before have I had this problem. Maytag says it is designed this way and I have to continue to buy AFFRESH (which is also very expensive). I have to use this two to three times a week and the pkg says once every 6 months - DONT DONT BUY MAYTAG. LOUSY.

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.

Nobody seems to know how to replace this part online. I have discovered what a POS this Maytag MGDC700VWO dryer is. The ONLY way to access this part is to beat an access hole in the bottom-left panel. After the repair, you are left with a nice 4 hole??? What an absolute POS! The back panel has screws but after removing them, I discovered the panel is also tack-welded! This is beyond stupid! Maytag used to be a great product before they were obviously sold to the Yugo factory. Time to move on.

Maytag Dishwasher Model MDB 7749SAM0 - Bought this dishwasher from Lowes in 2012 for my daughter and son-in-laws new home. Thought I was making a good choice with Maytag. Wrong. Same control board problem that everyone else is having. Wiring ribbon is corroded and shorted. Why is this not a re-call? I will call Maytag and Lowes and complain, but likely will get no justice. Sounds like I should just bring this machine to the dump and take my losses.

My Husband bought a Maytag Bravos Washer 2 years ago this next month. The washer is extremely hard on clothes. We have to wash all clothes on hand wash to keep them from tearing up our clothes, and we are having to replace the door lock for the third time. Of course the last 2 times were not under warranty. So once again, I cant do laundry when I need to. Thanks.

This is a Bravos MTC machine. It is a top load and has an energy star rating. Made in the United States. Impressed by its low water usage and Its ability to clean clothes. This particular model comes with a 10 year limited parts warranty, drive motor and washbasket.

I would not recommend a Maytag front load washer to anyone. I bought a Maytag Maxima 4 years ago and it looks like its not even available any longer so Im writing my review on a similar machine because after much research Im finding that all the Maytags have a similar issue. I have an MHW7000XG1 model large capacity washer. After 4 years the MCU went out and the cost to repair is $500. I looked up the error online and sadly there are so many others with the same problem. I had always thought that Maytag was built to last, however, after lots of research I am finding that 3-5 years is all you get before either the MCU or CCU (or both) have to be replaced. After replacement most people get another few years and then it has to be replaced again. By that time I could have purchased a brand new washing machine. The appliance repair company told me to get a Speed Queen. Thats the washer/dryer he has. They are built to last up to 20-25 years. Im a single mom and cant afford to repair my washer or buy a new one so it looks like Ill be doing laundry at relatives house for a while. Terrible product and definitely not worth the $1500 I spent on it 4 years ago.

My husband and I purchased our Bravo washer and dryer from Home Depot about 5 years ago. They have been the worst ever. Clothes always tear and we continue to receive an F1 error every time we try to wash something. I dont have the money to buy a new one, but I sure wish I did. I will never buy a Maytag anything ever!

We are a family of three. We purchased our Washer and Dryer New, November 2011 at Lowes, in Lindale TX. I am disabled. I have had several spine surgeries and getting ready for another. I was injured at work and it left me crippled. I do not receive any benefits from my County Employer. My wife is a schoolteacher. We live on a limited income after my accident. We purchased this set with utmost confidence, our last set was twenty years old. We updated due to water, electric, and the environment. Our Maytags we had were still usable, it was just time for their retirement. They were hand me downs washer and dryer set. Truly! I dont know how old they were. When our washer started having troubles, it was making a horrible noise. We called Hughes Appliance. Theyre an authorized Maytag Repair Service Warranty Center. They sent Mark out we used them before. He stated the motor was not loctited from the factory. It worked its way loose almost coming completely off. This cost me a $85 service call. Mark also stated that the Tub Bearings were going out because off this. He called Maytag Customer Service and Dealer Warranty Service, said they wouldnt pay for the repairs or even the Service call for their factorys snotty WorkmanShip. I tried calling myself and got absolutely nowhere. I was polite, courteous and nice and they still Said, Sorry, We Know its less than three years old but thats the way it is. Sorry Sir! Have Nice Day! Its going to cost $389 to replace the tub bearings in top load washer. The washer only cost about 750 less than three years ago. Its the most expensive clothes washer Ive ever owned. One thing! If they dont make things right, I promise I will never own a Maytag again! And when I am in a store and see someone looking at their product I will make a point to tell them my situation and about my Maytag Washer. One thing is certain I can make sure young customer dont buy the wrong appliances while I sit patiently in my wheelchair waiting on my wife. Thanks Maytag! Its not What You Did For Me! Its What I Can Do For You!

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

I purchased my machine on June 2, 2021 and it was delivered and installed on June 4. I have successfully done two loads of laundry. On June 9, I attempted washing two small bath mats and 2 dish towels. When I returned to the laundry room to place the load in my dryer, I found the the items in soapy water. I tried many times to reset the load with no success. On June 10th I called Maytag’s customer service and spoke with an associate who walked me through a couple of common quick fixes. These also were unsuccessful. She referred me to warranty service. I will not be able to have my machine repaired until June 23rd! Obviously, if their repair department is so overwhelmed, the products they sell are a piece of junk. I am furious with both the product and the service I have received.

Bought this washer back in March of 2016. This is the biggest piece of garbage that I ever came across! That washer does not clean clothes, when they are dirty. If I stand in the rain dressed in dirty clothes, they get cleaner than in the washing machine. In 5 month I have tried every possible variation of washing to no avail. I have to handwash the clothes that I wear to work in the garden, or any other dirty job, because the washing machine does not do the job! I bought that washer at ABC warehouse, I paid almost $400 for the thing, and I have to handwash my dirty clothes!!! Shame on you!!!

Purchased a Maytag smooth-top range about a year and a half ago. Ive only cooked frozen pizzas in it. Have only had it on six or seven times. Havent used the top burners at all. Its an electric range, and I just had it hooked up a couple of months ago, as I was trying to find a place for it in the tiny kitchen. The folks who lived here before me, had a huge refrigerator and gas stove right next to each other, and I didnt want to go that route. Anyway, I went to put yet another frozen pizza in the oven, and the light doesnt work!So, after only six or seven uses, the oven light is busted! My mom had an old Westinghouse Terrace Top range, and it lasted well over 20 years with no problems. The only reason she sold it was because she remodeled her kitchen. It still worked great after all those years. Its after-hours now, but when I call Maytag tomorrow, Im expecting to get the run-around, if the other reviews are accurate, and Im SURE they are. Wont ever buy another Maytag product again.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

We bought this Maytag Bravos 300 Quiet series top loading washer 3 years ago. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer. I absolutely HATE this Maytag Washer. DO NOT buy it. I would rate it less than one star however they did not offer a 1/2 star. If there is class action lawsuit please include me.

Neptune washer and dryer, an all around good buy. Low water use and large capacity for the pair. Bought the pair in May of 2001 and have only had one, very minor, service call. Buying online usually proves to be the easiest and cheapest way to go. Economical delivery costs. Noise and vibration and overall solid construction. Dancing washers can be a real cause for being a deal breaker. Auto shut off for balance is a must. Cleanliness of wash and wear caused by washing and drying. Large capacity and multiple cycle selections for both the washer and the dryer are necessary.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

I purchased my Maytag Bravos Washer/Dryer several years ago, and I have hated them ever since. The clothes smell and are wrinkled. The dryer never gets the clothes dry. It will run and run and run, and the clothes will still be wet. I previously owned a Maytag Washer/Dryer for nearly 20 years and never had a problem. This set is a piece of junk. When I go to Lowes or any store for that matter and see someone considering this product, I warn them as quickly as possible to stay away from this product. I will continue to do so. Shame on you, Maytag, for making such a horrible product and for being too weak to stand behind your product. I will never buy Maytag again and will do my best to make sure none else does either.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

We were replacing a 4 year old Whirlpool Duet washer (bought on recommendation from sister-in-law) that needed the third repair and was putting holes in our clothes. We had purchased the warranty (which we had never done before) so Lowes gave us the choice of machines and we decided to go with the Maytag Bravos. Lo and behold, were still getting holes in clothes. Several repairman told us the issue is common and is caused by the force of the water flowing into the machines plus the rapid spin cycle which pushes the clothes through the punched holes in the tub and the clothes catch on the metal on opposite side of the tub. Turns out sister-in-law had the same problem with her Duet and (not knowing I bought the Bravos and had the same issues) bought the Bravos and also is still getting holes. So I know its not just me.We also have problem with the machine not putting in enough water so clothes do not come out clean. In fact, a lot of stuff comes out with areas that havent even gotten wet during the wash cycle. I just want an old fashioned machine with an agitator that fills the machine fully, washes my clothes and doesnt put holes in them.

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

I use a late model Maytag front loader. It does a great job cleaning and uses very little soap and water. To date I have NOT had to call the repairman to work on it. All in all I am VERY satisfied.

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

At two different times today I was left on hold for thirty minutes each. I was told the compressor only had a year warranty on it, cant do anything about it. I then went online to Maytag web page and it read only on compressor the warranty had ten years. I called them after a very long wait and was told that was just started with the ten year warranty. I have owned many different refrigerators never heard of compressor only lasting 5 years. The serviceman who came out to tell me compressor was bad said the name Maytag used to stand for something but now stands for junk. Worse customer service, worse product.

I purchased this new a year and 4 months ago and have had nothing but issues. We thought it cooked slow or cooked high/low but couldnt be sure if we were just imagining it until we had family come down at Christmas and complain about how slow the top burners are and why is it taking so long to boil water. Then again family for Easter where they cooked three days in a row and they complained that our top oven either burns or under-cooks the food which we had noticed but presumed we just mistimed a lot of food. Just recently the bottom oven wont heat past 350 and just constantly says preheating. The top oven followed suit shortly after. Nothing past 350.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

I purchased a Bravo Washer and Dryer from Home Depot. The Maytag Bravo washer and dryer we purchased from Home Depot did not work from the beginning. Before I called Maytag, I tried for several months to redo the way I was loading the washer and dryer.I tried several different settings however, the clothing keeps coming out smelling like it is still worn. Spots are in the clothing that normally comes out with a washing (with my prior washer). The clothing just does not get cleaned and it gets so tangled that it has ruined some of my clothing. There is clumping of the detergent, even though not a lot has been used.I had the repair company come out three times for both the washer and the dryer. They have checked and no errors codes where found. One gentleman told me again to redo the way I load the washer and the dryer. I have done it so many times, but I tried again and even purchased little dryer balls. It made no difference.I called Maytag again and was told they would have to have another company come in and do a second opinion. The person came and said that he agreed that the washer should be able to wash and the dryer should be working correctly. He recommended that a possible problem with the motherboard for the dryer (which was a possible problem mentioned by visit #2) could be handled, but he had to have it approved. He would check with the company and get back to me. I received a call the next day and a message was left telling me there is nothing he can do with the washer. He was told by Maytag/Whirlpool that I should only fill the tub lightly and not pack it down (I told everyone how I load and I never pack my clothing down). The washer should, when loaded with wet clothing, be only 1/3 to full otherwise it decreases the wash ability dramatically.The problem of the siphoning action for the softener section of the washer should be handled by running boiling water through the tube to loosen up the wax portion of the softener. The possible correction for the dryer exchanging the motherboard (it could be set incorrectly) was turned down by saying that the dryer is running to Maytag/Whirlpool’s satisfaction and nothing else would be done, since there are no error codes for both washer and dryer.My towels have a mildew odor to them when they are used. They have to be washed twice and run through the dryer a long time before I can put them away. I purchased a high capacity washer and dryer and I am told now not to fill it more then 1/2 full. That is not what I was told by the person selling it. Otherwise, I would not have purchased this set at all.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

After 16 months my Maytag dishwasher control panel went bad. The company told me they could not help me. I asked for a new control panel to install myself, no luck. I bit the bullet and bought one online for 110 dollars. 2 months later... you guessed it, its bad. Now I have to send it back under warranty. It was a Maytag name brand OEM part. I thought Maytag was a reliable name, I thought wrong. Never again.

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

Control Panel MDB8949SBB - I purchased my dishwasher in August of 2013. The control panel has stopped working and Maytag refuses to discuss the issue with us. Regardless of how many complaints they receive they are in denial about their product. They now offer a Repair +1 program which costs $260 for a repair and an additional 1 year warranty. If I do that I will get 1 year out of it before I run into the same problems. Any ideas?

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

We are on our 2nd Maytag washer with the 1st being a top load with agitator and the second without. Both were also bought used. The 1st one broke after I was cleaning it so totally my fault but the second one the door lock broke. Aside from that they do wash clothes well and but I do wish there were more or different cycle settings. Overall they are good machines for out price. (Being used that is.)

The Maytag Neptune TL washing machine has always been extremely loud! It smells awful and now our clothes too! I have found mold in the washer and cannot get it all out even with bleach. My children are extremely allergic to mold and they have had problems because of this. I am very disappointed in this washer and find it sad that no kind of action has taken place to help people who have bought them.

Horrible machine. Purchased on 02/28/2014. I am 63 y/o retired housewife now. Machine used only for light washing, occasional king size sheets and weekly towels. I bought into the Maytag name, am so very angry that I did. Started a load at 1215 pm today... it is still sensing, washing, rinsing, spinning and then it starts all over again. Just unplugged from the power source, hopefully I can get the clothes spun out enough to dry!! Call and live chats to Maytag were frustrating to say the least. $400 plus Maytag service call to check out the machine not fix check out repairing would be extra. (I do not live in rural area, live 5 minutes from downtown Jacksonville FL!!!) Independent Repairmen will not touch this Maytag Model (cannot say I blame them!!). DO NOT PURCHASE A MAYTAG PRODUCT. This is a horrible company lacking in integrity, honesty and fairness. They sell shoddy, inferior products based upon past history.

My husband and I are very disappointed and upset about our new Maytag Dishwasher model MDB8949SBM. We only have had this dishwasher a little over a year! We purchased in May of 2014 and in June 2015 the control panel lights were acting crazy. Actually I even think it started earlier but just thought it was me pushing buttons wrong and wasnt that bad. Then in June any button you push on would not even light up!! I have stopped using dishwasher since June and now it is October! I was so done trying to push the right cycle that I wanted! I will never purchase another Maytag ever!! Just saw there is a Lawsuit here California. Yes!! But I have not seen any information yet on this lawsuit. I am calling Maytag!

Like so many other people reviewing Maytag refrigerators with bottom freezers, I am dealing with water on the floor. At 64+, I am not eager to tackle the problem as a DIY project. Once of defrosting and cleaning up was enough. I love the looks of my 2 yr old $2000 4 door fridge/freezer but hate the issues. I guess Maytag is going to ignore all of us. When someone finds a reliable company, sing it from the rooftops.

We bought this washer in February of 2010. We had the pump replaced under warranty in January of 2011, and the pump appeared to have a hole in it from some type of hard object that had gotten inside the pump and damaged it. We then replaced the L-shaped hose between the tank and the pump because it had a small hole in it - very thin rubber. Last week, the washer was leaking again and the service technician said that the pump housing was cracked due to a penny rattling around inside the pump.This washer performs very well when it is working but it seems to be too fragile to handle on normal usage. The Whirlpool washer we replaced with this one ran for 23 years with no problems before it finally went out. From all appearances, it seems that every failure we have had with this washer has been due to damage from foreign objects getting trapped in the pump. Is there no screening mechanism to prevent hard objects from entering the pump? This seems to be a design flaw more than anything.