This Maytag Centennial is the WORST piece of junk I ever purchased and I received the same uninterested response from Maytag as everyone else. Maytag sent a service man out who said it was functioning as it was intended. Once started, this washing machine cant stop if you forget to add an item. It dumps out all the water and starts the hour-long cycle over. All settings are an hour-long cycle. Unless Bulky or Delicate is selected you only get 2 inches of water -- Even for Heavy Duty. No matter what the setting, the clothes do not come out clean. You must hand wash them first. Maytags are no longer a desired product.

I bought this Maytag oven (MEW 7627HB) to replace a 20-year-old GE double oven. Upon the first use, I found that it has noisy cooling fans which run continuously as soon as it is turned on and, for some time, after it is turned off. These fans make an irritating, loud, whistling noise. The dealer responded to my complaint, pulled the oven out and performed a complete system test. He then called engineers at the Whirlpool factory, who told him that the fans were a recent redesign made because the previous design didnt satisfactorily cool the electronic control circuit and that there was nothing to be done about the noise. After several weeks, the oven, when in use, continues to stink of overheated electronics. I fear it wont last long.Note that my old GE model, which also had electronic controls, didnt run a fan at all unless both ovens had been on for some time or the self-cleaning feature had been on for a while. And it didnt make a loud noise.

My Maytag Bravos washer is 6 years old. I had to have the motor replaced about 2 years ago. Now, it gets stuck on uL on every spin cycle. I had a technician come, and was told its just cheaper to replace the machine at this point. What happened to the Maytag man of old, the one who never has any work to do because the machines are built so well?!

These are the issues, Water level is ridiculous, clothes often have dry spots, I use only the high water level which is a joke. The tub bottom is very hard to reach because it is too deep even for a man with a long reach. The tub itself is about 16” deep but never fills more than 4” of water on the high water setting. Why such a deep wide tub when you can only put 4” of water? Cleaning is poor, the machine is very noisy, very. The worst machines we have ever purchased with ridiculous sensors, bells and whistles. The dryer takes forever to dry clothes and again the sensors are a joke. The high efficiency of the units means you work much longer for clothes that are wrinkled, spotted, less clean looking and sometimes damaged. Where is the savings? And don’t say hydro and water as the washer cleaner cost, wipes that out and more. We gave our 26 year old machines to Habitat, neither machine was ever serviced and were in perfect condition, they were Maytag. They have destroyed their name. So sorry we decided to modernize our laundry room.

Works quietly and efficiently and I love it! I dont even know its running and the dishes are sparkling clean when they come out. How could ask for anything more. I would always purchase this brand again. The reliability is another factor, I have had Maytag before.

This washing machine just sprinkles water on your clothes then ties them up in knots. And to add insult to injury, needs repairing every year or so. Horrible! It does have a couple of redeeming qualities, but they definitely dont outweigh the cons. It spins the clothes quite dry and has a large capacity. I have dogs and kids who play football and a husband who does construction, and its not unusual to find lumps of dirt and fur trapped in an article of clothing or blanket. All my bras and sweaters get ruined, it twists them up horribly. The blankets and sheets end up in a mushroom shape. Sad to say, NOT good. I like Maytag, but not BRAVOS.

The Bravo HE Washer was a cheap piece of garbage and I am very surprised Maytag put its name on it. It broke down exactly one year after the warranty went. It did not ever clean clothes properly and all stains remained even when you spot clean first and double rinse. Maytag basically ripped us all off and somebody should start a class action lawsuit for this thing they call a washing machine! What a joke! I wont repair it. It will just fall apart again. Im not stupid. I know this is how they pay their employees doing house calls! So now, I have to go to garage sales and look for one made in the 1970s because that is when machines were made in the USA and things were built to last, not this crud. Maytag should be ashamed. It is time for them to close its doors. Sorry but its true. They are just crooks now selling crud that falls apart! They owe me a full refund.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

Save money. I have always had Maytag & loved them until I bought the Bravos xl top load washer. The salesperson insisted it was a large capacity energy efficient w/ great maintenance record -- greatly misleading. The water level does not rise enough to effectively clean or rinse so clothes do not get cleaned or detergent doesnt rinse out thus allowing only 2 to 3 towels or jeans to wash per load. Such ineffective cleaning cycles create the ongoing need for loads to be rewashed and be extremely small, yielding credence to other consumers’ accusations of being mislead and false advertising of xl capacity. As such, it takes hours to wash a family of threes clothes. The machine shakes like crazy and clothes get ruined as they get twisted and tangled into each other ripping, tearing, misshaping and ruining them.

I bought a front loading Maytag Cloths washer model# MHW3505FW1, SER# C71451407 new in April 2017, from Home Depot, since then it has broken down three times, with a water pump, a master board, and now another master board, we were told by the appliance repair service that is used by Home Depot extended warranty service, that it will take a month to receive the master board. Thats it... Never again will we buy another Maytag or Whirlpool product. This is unacceptable. Gone are the years when Whirlpool and Maytag made quality products!

Purchased a Maytag fridge April of 2012. Within a few months the freezer was not keeping the food cold enough. I had a lot of food loss. I called Home Depot and they refused to give me a new fridge. They said to call the Mfg. That I did and all they did was send out a service man. This has been fixed 5 times for the same thing. The problem now is that the Extended warranty company refuse to repair it now that they know that it was a pre-existing condition that should have been taken care of under the Mfg. warranty. I paid 180.00 for an extended warranty that now is worthless. I just threw out roughly 200.00 worth of food. Now my lettuce is frozen, eggs are frozen. My husband is disabled and money is not plentiful. I dont know where to turn. Frustrated.

Maytag Dryer MED6000XR2 - Purchased in Sept. 2012 - first service call 1/13/14; 2nd service call 2/20/2015 and less than one month on 3/14/15 it goes out again. It takes one week to get service company out and then another week for the part to be ordered and put in. This means I am without a dryer for over 2 weeks. An $1,100 dryer goes out every year and sometimes within one month?! According to the service company, it just is the way this dryer works. Really? If Maytag ever wants my business again, I better get a more justified reason and better than 2 weeks service call. This is absolutely ridiculous.

The Maytag Washer and Dryer we bought new and they have been great. The dryer was bought in 1972 and still works well. The washer was bought in 1997 and still does a good job. We are satisfied with the long time these 2 appliances have lasted. Do any appliances manufactured today last that long?

Do NOT purchase a Maytag dishwasher. What happened to the Maytag repairman being so lonely. Now he has lots of company in the way of angry consumers. Purchased a Maytag dishwasher and less than a year later the control panel failed. It was still under warranty but the service person just tweaked it instead of replacing it. Now, less than a year later it has failed and will cost over $200 to replace and repair. This is disgusting.

I just purchased this Maytag Commercial Technology Washer and Dryer on August 31st, 2018 and We hooked it up today Sept 4th 2018. I put a small load of towels in this machine and it said it would take an hour and thirty seven minutes to wash. I added my detergent and pressed all of the necessary buttons and started the load. the machine started spinning and testing and adjusting. I waited to hear the water start to come into the washer but nothing. I then checked my water lines thinking they are not on but they were. Through the smokey glass on the washing machine, I could see water dripping as if it is hooked up to a slow drip IV Machine.I am taking this thing back ASAP!!! First thing in the morning on Sept 5th 2018 I do not need to call Maytag Customer Service because they know it is a piece of junk, so I do not need to waste a moment with this crap on my property. I see Maytag does not believe in a QUALITY ASSURANCE DEPARTMENT because that department would put a stamp of approval on this Junk for distribution.No Washing machine should take more than 30 minutes (40 mins max) to wash no clothes. I will have to invest in an old school scrub board and rocks, then I can understand an hour and thirty minutes worth of wash time. I have set the timer on my phone when I started this load and My towels have been in the washer for an hour so far and I can still hear the slow IV DRIP OF WATER going. I just checked the machine and the digital reading is saying it has an hour and thirty three minutes to go. there is no water in the tub of this washing machine. The towels are wet from the IV drip and the machine is now pretending to agitate the dirty towels but it is only going in one direction. It is truly a sad state of affairs, your hard earned money gets you nothing but junk and a runaround.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

After 1.5 years, our Maytag bottom freezer ref has started leaking water on the floor. There is a sheet of ice on the bottom of the freezer, and ice in the slots on the back wall. This sounds like a frozen moisture drain. This seems to be a common problem. There should be a recall.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

I also bought a Maytag refrigerator in 2013. Right after the warranty expired it was forming ice on the bottom and back of the freezer and was not making ice. I called Maytag and they told me they have no complaints on this type of refrigerator. It was also always making a lot of noise. Maytag was supposed to be the quiet one. I will never buy another Maytag product and I will do anything to make sure nobody else does either.

I purchased a Maytag 4-door model, a little over three years ago. A little over a year ago, I noticed small puddles of water around the bottom of my refrigerator on the floor. I blamed the dog for having accidents and shrugged it off. Well, after months of putting up with this I came to the realization that it wasnt my dog, so I started looking for leaks on the seal, etc. Thats when I realized that the entire floor of the freezer was one solid block of ice! So, I looked online for people that might be having the same problem. Sure enough, there are A LOT of us!!! Now to add insult to injury, I have to have a MAYTAG certified repairman come and look at what needs to be done! He only charges $85.00 just to come to my house!!!! Thanks MAYTAG, I spend $2500.00 for a refrigerator thats obviously defective, and still have to pay more to have it repaired!!!

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

Ive been a Maytag consumer since 1980. I bought washer, dryer, refrigerator and a smooth top oven. I replaced the washer and dryer with the Bravos series on November 22, 2011. Everything was fine until 6 weeks ago. The bearing went bad under the drum. 2 techs and 2 weeks later, at the cost of $527 and change spent on repair for a $650.00 machine, I started to look into reviews. Not! Can you say class action lawsuit! The fine gentlemen informed me 5 years ago about the Canada buyout, a local retailer that only sold Maytags. He shut his doors due to the fact that he will not work on junk! Oh well, he was right. 13 months worth of use and Im going to spend that kind of money. Now I understand why the repairman in the commercials retired! Shame on you. Love, crazy Mike.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

I love it. Laundry as well as horse blankets. It does it all! I have never ever had one problem with it. Love the delay start setting as well as the extra rinse cycle.Easy to clean the gasket and keep the soap dispenser out to air between washes!

Bravo Series Washer and Dryer. I hate, hate, hate this washer and dryer. I have had it for 2 years and hate it more every day. What makes is worse is the over $2,000 spent to buy this piece of crap technology. The engineer should be fired and sham on Maytag for selling such a piece of crap. Washer does not get clothes clean and I have pictures to prove the amount of dirt and lint and soap left on clothes and bedding. Very poor design, and worse yet absolutely horrible engineering.To wash one item on delicate takes 47 minutes. No way around it and you are limited to the water temperature you want to use and the spin cycle that you want for that item. Water level is too low no matter what setting you use. I have read and reread and gone step by step according to instructions with no success of clothes coming out clean. Clothes are also twisted and knotted and wrinkled like no other machine I have used in over 50 years. The washer is very limited in what it allows you to do. Bedding cycle is a joke that does not work at all. One of the reasons I bought this was so that I would no longer have to take the time to drive to a laundromat. I washed a comforter and so much soap and lint and dirt was left on the comforter. I still had to take it to the laundromat to get it clean.Dryer is just as bad. Even with the energy saver off it still takes 1 hour and 20 minutes to dry 4 towels that are 5 years old. I cant imagine how long it would take to dry brand new fluffy towels. It was engineered to sense when ONE piece of clothing is dry. I want ALL my clothes dry, not one piece and the machine shut off. How stupid is that??? Engineers - design it so it senses when clothes are still damp and the machine keeps running!!! I can only use the time dry setting because no other setting even comes close to getting the clothes dry.To top off the hatred of this machine some damn engineer apparently thought this was a car and needed to be aerodynamic with a curved lid on both washer and dryer so you cannot put anything on top of the machine!!! Not every house is 5,000 square feet with plenty of room and storage!!! They want to force you to buy the drawers to put underneath and then the washer becomes too tall for short people to reach down into to get the clothes out. There is not one positive thing I can say about the washer and on top of it I will never purchase another item from the store I bought this set from. I have had service come out time and time again and they say it is an installation problem. Installation says it is service and yet no one will admit it is just a very poorly designed machine. Do not buy this brand or series of washer and dryers. This series deserves a minus and the company should replace every set sold!!!

Our control panel just went out...purchased in November 2015. From reading reviews it appears our only option is to purchase a new control panel and hope for another two years. Ours (MDB7749SBM3 Dishwasher) was purchased from Sears and was not cheap. When is Maytag going to recall this panel? I read reviews that this problem goes back to 2011.

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.

The washer w10420491A is 2 1/2 years old and got the F51 code. The result is the hub bearing are shot along with a circuit board. I would stay away from any Maytag Bravos washers.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

I purchased a 2006 model Maytag Top load Washer and Dryer used 9 years ago January 2010 to replace a 2009 Samsung front load washer/dryer. I had to replace the agitator on Maytag washing machine before I could use it. Fast forward November 2018 the washing machine stopped agitating the clothes, but would spin the water out. I replaced 2 belts and thoroughly cleaned underneath and inside washer to remove soap residue. Maytag washing machine has been used twice a week since 2010-2019 and still going strong. Maytag dryer has never had any issues. I also own a set of 25+ year old Maytag Washer/Dryer both still working.

Since the day I bought the Maytag Bravos XL washer it never worked correctly. An entire year of several repair men, which half said there was something wrong and other half said nothing was wrong with it. Now it sits in my garage as the most expensive paperweight. After repeated requests, the Whirlpool company that owns Maytag now refuses to stand by their product, replace it, refund it or anything at all. They have washed their hands, yet I cannot wash my clothes in it!

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

My Bravos XL is worthless!!! This lack of agitator design is totally ineffective. Dark clothes come out with white powder on them and I use the liquid detergent. Whites I soak with detergent and bleach then full wash cycle. Still stains on dish towels and socks. Never had a problem with the old agitator Maytag. And yes the wrinkle free cycle creates wrinkles. Deep water wash is only cycle that even comes close to cleaning and its far from perfect. Horrible waste of money, buyers beware!!! I thought all those negative reviews were overblown and since I couldnt find a large enough machine with an agitator, I ignored warnings and bought this garbage. Matching dryer is fine.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

less than 2 yrs old and has completely failed to operate. We have been patient with this model. It does roll the clothes to point they are wrapped around and among each other and must be pulled apart before placing in dryer. The wash cycle now takes more than 45 minutes, It fails to spin the load often. Now, it has failed to the point it will not operate with or without any clothes in it.

Bought my Maytag washer and dryer as a set in Feb 2011...like many, I did not get the extended warranty, as I thought this was a great brand. Ive had nothing but problems with both. The dryer takes two rounds to dry, the lint filter is wet and rusted. The belt has popped off and needed to be put back on..The washer does not clean very well. Ive replaced the shift actuator because it was not spinning, now it sounds like a turbo jet taking off. And as of a week ago, my washer started leaking underneath. Paid a tech to come look at it and said my motor was done and Im better off buying a new washer and even recommended that I do Not buy Maytag! So I googled Maytag Bravos and seen all the poor reviews and realized I wasnt the only one! My set is 3 years old and its ridiculous that Ive had these issues, as so many has. Extremely disappointed of this brand and I too, will not be buying Maytag ever again!!

First front loader washer and love it. Saving on water, less tangling of clothes. So far they are quieter than others that I have had. The dryer is almost 10 years old and the washer less than a year. The machine I had previous to this was top loader that had to be replaced, would no longer spin.

In July, 2014. I bought brand new Maytag refrigerator with bottom freezer. After 4 years, compressor leaked, and not cooling at all. I tried to check warranty, and Whirlpool Canada said that only specific model has 10-year warranty on compressor issue and mines does not have. So frustrating. Simply dont buy Whirlpool product. This is totally garbage and not reliable company. LG or Samsung has 10-year warranty on compressor for every product.

I love the bottom freezer & refrigerator on top. Its so convenient... but it really could have a little more refrigerator space though. I love the stainless steel. It makes the fridge look regal. Also, the fingerprints do not show.

In December of 2013 I purchased a Maytag clothes dryer model Neptune. In July of 2014, I was hearing a banging sound as the drum rotated. As a mechanical inclined person that I am I removed the top of the dryer and turned the drum by hand. As I turned the drum I noticed that the stainless steel crimped bead around the drum had separated just enough to hit the side wall of the dryer. I was able to bang down the raised portion of the raised bead. This was a quick fix and there was no more banging as the drum turned around. Then in June of this month it started to make that banging sound again. So I removed the top of the dryer and discovered that the bead separated again and then there was a crack that spread to about 1 1/2 inches. I banged down the raised portion again and this lasted for 2 weeks. That’s when I noticed that the crack spread further apart and actually ripped a hole in the left side wall of the machine and froze in position where it would not turn at all. So I reversed the turn of the drum by hand to allow the drum to turn again. At this point I decided to order a new drum which came to $264.00 which included shipping. When it arrives I will replace the entire drum. Being that Maytag/Whirlpool refused to honor their product because this issue happened after the warranty had just expired and the company didnt want to replace the drum. I have never heard of a dryer drum seal bead coming apart in all my experience with repairing an appliance. No I wouldnt suggest purchasing a Maytag/Whirlpool product to anyone. I feel the company should have done the right thing and replaced the drum. In life if you do the right thing all the time, then there would never be an issue with the consumer and corporation. Always do the right thing and you will never go wrong.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

We renovated our kitchen in 2008 and installed all Maytag appliances. We had purchased a Maytag dishwasher 3 years prior to the renovation-- that we kept. Well, the dishwasher was the first Maytag appliance to go. After replacing several cheap plastic parts on the dish racks (I resorted to use twist ties at one point to hold the racks together) the racks started to chip and rust, leaving stains on our dishes. The cost to replace the racks was about $150 so we just replaced the dishwasher (with a Bosch - so far, no problems!)Then, a couple of the igniters on our gas cooktop stopped working. Since they were the back burners that we didnt use much, we just used a match to light them and let it go. Next, one of the hinges on the double wall oven door snapped. This is a little concerning because the doors are heavy and will need to be replaced. And the final straw concerns our French door refrigerator. The control panel started flashing wildly and the ice door was opening and closing with a loud clicking sound. Of course this happened on a weekend so I looked online and found hundreds, if not thousands, of similar complaints. So I called Maytag and spent nearly an hour on the phone only to be told that my model number was not one of the recalled ones. I explained that my problem was exactly like the others and was told that the best they could do was offer me 50% off any parts. The service call and shipping would not be covered either. The Maytag representative that I spoke to tried to cheer me up by telling me that at least they had the part I would need in stock, unlike the recalled models. Those parts are discontinued and have to be specially manufactured and have a two month waiting period. The part is about $250 and add to that the shipping and service call and I am sure this is going to cost me several hundred dollars even with the discount on the part. Very, very disappointed. Never again will I buy Maytag, never again!

Purchased a new Maytag dishwasher just under 1 year ago. After a 5 months it started not working. We called the dealer - who gave us a number to call because it was under warranty. We called the number and it took days to get someone to look at it and not fix it. It needed a new part. Its been over a week now and we havent heard anything, and still no working dishwasher. Our last two dishwashers lasted over 18 years. Kenmore and Whirlpool, never had any issues. This is our first Maytag. Service has been snail pace slow. Dont buy a Maytag dishwasher unless you want to spend your life washing dishes.

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

The dishwasher turns on of its own accord. Sometimes when you get too close to it, once in a while in the middle of the night, and most of the time when you latch the door. It does a great job cleaning the dishes, but to no avail because its always in the middle of a cycle when you need them.

My Maytag dishwasher MDB780AWW2 was recalled due to electrical problems. They gave me a voucher to purchase another one, plus I had to pay another installation fee. New unit was installed in February 2011, and here I am with a control panel issue. Seems like a similar problem, too. The lights light up, but the dishwasher wont start. Its another $345.00 plus tax repair by a repairman.

Just bought a washer and my clothes are always left with dust and dirt on them after washing. Called Maytag, they sent a technician over, but he found nothing wrong. Company refuses to do anything about it, including exchanging it for a different model, since weve had it for more than a month. I am extremely dissatisfied since I just lost over a grand on a washer that doesnt actually wash my clothes.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

I spoke to Destiny today at the Resolution Center, she knew one phrase, its a low usage washer. I would reply, 3 inches of water in a drum does not wash my familys clothes. Every load is covered in white soap specks, whether powder, liquid or pods are used. Again, Id hear, its a lower usage washer. Ok, I got it.The machine has been cleaned with Affresh.This washer cannot clean a single shirt let alone a full load of wash. Maytag (actually made by Whirlpool) should be ashamed to produce such a shoddy product and expect to the consumer to keep paying for repairs. From reading the reviews on a couple of websites, consumers have to keep repairing this washer time and time again. Destiny told me she would send a technician out at my expense. The machine will be in the landfill on Saturday. Never again Maytag/Whirlpool.

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

I bought a full Maytag kitchen in 2010 because like many others, I trusted the brand. However, before I knew it, the dishwasher broke down. I live in Canada so I get Whirlpool (owns Maytag) 2 year limited warranty. Thank God for that because I have had the repair guy come 7 times. Each time for the same problem (control board) and they have replaced a listed of parts with no success. I have asked them to honor their no lemon policy but am given excuses as to why someone has to come see it first before they can give me a new one. Once the service guy arrived he obviously has no idea about anything and just goes for the repair. Its so frustrating.I am fed up. It is completely unacceptable because now Im losing money staying home waiting for the repair guy. Maytag is the biggest piece of junk I have ever bought. I only hope you see this before buying a Maytag product. Like many others here I use my dishwashers once a week. Now Im faced with a dilemma where I might have to purchase a new dishwasher as soon as my 2 year warranty runs out. My $700 went down the drain.

Oven failed after 2.5 years of normal use (1-2x / week). Apparently a relay failed (and burned out bake element). Contacted service & parts dept and learned that repair would cost $100 for service visit and $413 to replace the control board. Only the $80 bake element is covered by the limited warranty. Wonderful oven if your hobby is appliance repair. After 2.5 years, it now functions better as a toilet than an oven.

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

We purchased our Maytag Refrigerator Model # MBF2258DEHM on 12/21/2015. Just a couple of issues I would like to bring to your attention before you purchase your Maytag. The single refrigerator door does not close automatically. You have to close the door. The metal handle is metal and has a metal smell and feel to it. The stainless steel door and the handles are not the same finish. Although this might not be a problem for some who like the industrial look I prefer my hands to be free of chemicals while I am preparing food. The ice maker takes up too much room. The ice maker should have been an option, not a standard item. I had a Kitchen Aid for 10 years and loved it. I thought I was going to have my Kitchen Aid for 15 years or more. I would have purchased another Kitchen Aid, but the reviews were not good.

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

I purchased a Maytag dryer several years ago, not a fancy one but just a plain simple dryer (model number MDE2706AYW). Thank goodness from the other complaints I have read I didn’t buy one that is computer controlled. The heating element has burned out twice, main thermostat and limit thermostat has burned out, and if you look close, it seems the wires are trying to melt or at least the insulation. Well, the insulation is melting. And the venting system is cleaned regularly so they can’t blame that. The last dryer I had lasted well over ten years with zero problems. I should have just fixed it. I’m sure I wouldn’t have spent as much money on repairs as I have with this one. You remember that lazy Maytag repairman that was on TV for so many years, you know why you don’t see him any longer? He is at my house repairing my ** dryer! You never, never hear me say this but the next dryer I buy will be made overseas. My last appliance purchase with any of these name brands on them: Maytag, Jenn-Air, Amana, Admiral, Crosley, Magic Chef, Performa by Maytag, and Norge.

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

The mid level dishwasher is excellent, easy to install. Very quiet. The dishwasher cleans well and does a great job. I wish the default would go to the last setting instead of auto. Highly recommend.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

Need to keep cleaning washer otherwise it leaves white marks on clothes. I used vinegar but that didnt help. Used the wash cycle and that didnt help. I found a washer cleaner and it works great. Overall performance of washer is fine but I would be hesitant on purchasing another Maytag Bravo washer only for this reason.

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

My Maytag refrigerator is less than 5 years old; the compressor went out (only warrantied for 1 year, 5 years used to be the minimum). I contacted the company who now owns Maytag, I believe Whirlpool. They told me they can fix it, no matter what the problem is, for $380.00. It turns out they sold me an extended warranty, but that was never explained in the conversation. Prior to contacting them, I had Sears out to fix it; they are the ones that told me it was the compressor. 1 week after buying the extended warranty, the repair company came out to fix it and found out the refrigerator was unplugged and informed me it needed to be plugged in for 24 hours in order for him to determine what was wrong with it. I scheduled an appointment 1 week later. When they came back, they said it was the compressor, and they needed to order the parts. 1 week later, they came back, and the compressor they came with did not work. 3 weeks now, no refrigerator. They said they would put a rush on the order, haha. Now, I have to wait another 8 days for them to come out to repair. 4 weeks without a refrigerator? I think there is some type of implied warranty when you purchase large appliances; these companies are getting away with murder. Are refrigerators now disposable commodities? Cheaper to buy new ones than repair the new ones? What will happen to our landfills?

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

The machine runs and runs and runs and still the clothes come out dirty. Clothes are often not even wet all over. The Maytag HE water-saving washer is a terrible Hoax. The dryer also is faulty. It rolls the clothes into a big, undried ball of dirty clothes.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

I purchased Maytag washer/dryer set in Feb 2021. In June the washer broke. It took 2 weeks to get repair person to look at it. During the appt no faulty product was identified so they dont know what to replace. No parts were available. A follow-up appt was set for 1 month later. No parts are available to make the repair so a follow-up appt would be futile. . The only communications other than No Parts is that they want me to purchased an extended warranty. I will never purchase another Maytag product or recommend them to anyone. Meanwhile my warranty continues to time-out and they dont have any parts or idea when they will be available. Im not sure how a company can sell products that they do not have some level of support for those products. Beware of purchasing Maytag Products.

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

Same complaint as most of the others: bought a refrigerator in 2013 and about one month after the 1 year warranty had run out the freezer started leaking water all over the floor and build up is on the bottom of the freezer, making it difficult to pull out the metal drawer. :( We do not have the water even hooked up to the automatic icemaker so have no clue where the water is coming from. Clothes washer has never worked properly from day one, didnt fill up with enough water. Had the repair man here while the warranty was still in effect and he verified that the washer DID not fill with enough water therefore leaving soap and grime on our clothes. :( He had to order an entire new brain and replaced it. Worked for a couple of months better than it ever DID and now back to soapy, grimy, dirty clothes again. Why isnt there a recall on the part that keeps backing up on these bottom freezer Maytag refrigerators? Someone needs to start a class action lawsuit and get these things recalled and replaced. Spent a lot of money on this brand new refrigerator and was so jazzed to get a brand new one for the first time in my life. :( Well that was surly short-lived. Shame on you Maytag, your company has really gone downhill. I would love it if an attorney could start a class action lawsuit with Maytag on their bottom freezers.

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

I purchased a Maytag MDB7749AWW dishwasher in March of 2012. The electronic control on this unit failed in June of 2013 (3 months out of warranty). I have been trying to get a replacement part for over a month; the part is on backorder and unavailable. Whirlpool is unable to tell me when the part will be available. So, I have had no dishwasher for over a month and have no idea when, or if it will be repairable. Additionally this part is $150.00 and another $75.00 to have it changed. So it is going to cost me $225.00 to repair a 15 month old dishwasher that I paid $450.00 for. I have received ZERO support from Whirlpool. They told me today, 7-31-13, that the part is still unavailable and they will notify me in 3-6 business days as to if they can find a part. After seeing all the issues other people have had with this part, Whirlpools total lack of concern or support for the consumer and the cost issue it makes no sense to repair this unit only to see it fail again in a year or so. Basically I have a $450.00 boat anchor. The retailer purchased it from feels bad and is offering me another manufactures machine at a reduced price. Maytag has refused to do anything for me. I will never buy another Whirlpool / Maytag item again and I do intend to add my name to the pending class action suit.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

I purchased a Maytag Bravos XL Top Loading Washer and matching dryer in 2013. I had a repairman out to install a new screen on the dryer because the lint was spilling over into the surrounding area. The new screen has been catching most of the lint, but I still have to vacuum the surrounding area after a few loads. Also, I have to turn the dryer on two (2) cycles in order to dry most of the clothes, and the machine makes a lot of noise. Those are minor problems compared to the washer. It constantly tears holes in my towels and wash clothes. I NEVER put in a full load because the water level is so low, and it does not clean the clothes. It takes a long time to go through cycles and it is EXTREMELY noisy.I called Maytag and they said that they never heard of the problem of creating holes in towels and wash clothes, and wanted to charge me over $100 to have a repairman come out. They also said that the repairman might not find anything wrong. I feel that the washing machine is very hard on the clothes - like the salesman at Lowes said It’s like beating the clothes against a rock. The washer and dryer are JUNK, and I would not recommend these to anyone! I would trash them, but they were very expensive and we cannot afford to buy new at this time.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

The Maytag Neptune FAV6800AWW Washer has to be the crappiest product I have ever bought. I bought it brand new and hardly ever used it. The first time it broke it was luckily under warranty, although we had to pay for the repair man to install it. It took two new circuit boards before it was fixed. A few months later, the circuit board went again, and it was conveniently for Maytag now out of warranty. The repair man told us that their company never carried these washers because from the get go they had a ton of problems. He said that the odds of it breaking again were great and that we would be better off putting the money into a new washer.I dont understand how the company, in good conscience, could continue to sell a product to consumers that they knew was faulty. It was not a cheap washer and I have never been so disappointed in my life. You would think they would have had a mass recall or, knowing how many problems consumers were having with the product, offer so much money towards a new one.I laugh at the commercials where the Maytag man was bored because their product never broke I could have kept that man busy for months!

We purchased our Maytag Neptune washer and dryer in 2006. Months after our purchase, we tried every HE detergent we could find to see if our towels would smell fresh. Nothing we have tried has worked. I just went to Maytags web site. I found out there was a recall on this washing machine due to the mold on the door gasket. Why didnt they send me a recall notice so this could be corrected with a refund or something?

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

I can see by the comments on this page that the letter I sent to Whirlpool was in vain. I purchased a Maytag double oven gas range (MGT8775XW00) from our local Lowes. We were remodeling a home we had purchased. Unfortunately (as anyone whos been involved in home remodeling/renovation knows well), it took much longer than I thought it would before range could be installed. It was several months later before it was installed. First time I tried to use the top oven, it would heat to set temp (I assume) and then shut down. The larger bottom oven had erratic heating. I tried adjusting oven temps but it was a guessing game. We had Fix-Rite Corp out twice and they were puzzled by the problem. Two times, they replaced the control panel. After the second repair, it was decided the only thing to fix the kitchen was a complete gutting, new cabinets and floor. The oven was pulled out before I had a chance to use it again. By the time we got the kitchen finished and range reinstalled, I discovered the oven still had the same problems and the broiler would ignite sometimes and when it did, the flame would go out after 30 to 60 seconds and would not come back on. By this time, we were past the one-year warranty. After the first repair did not work, I tried to get Lowes to take it back and assured them I would purchase another range from them. They said they could not do that. Now I can see Im going to end up buying another range. Be assured it wont be Maytag and it wont be Lowes. I also own and use Maytag washer and dryer.

I love my washer. I have had it for 13 yrs and has only needed repair once. My complaint is the gasket on the tub has black mold that grows on it. I have cleaned it with bleach, bathroom cleaner, alcohol, but it always comes back. What can I do to prevent illness from mold?

I bought a Maytag MEDB835DW0 s/n M51202974 just about 2 months ago brand new. After less than 2 months it malfunctioned that it would not start. I called the customer service center on Sept 11, 2015 to report my problem. The rep I got was polite and caring and said she would keep on top of this. On Monday I called the customer service again to get an update. They could not locate one of the authorized repair people. The one they found did call me back but I was out of their service area and would not service my dryer. I was told that my problem was turned over to their Maytag/Whirlpool research or resource to find a repair and I would be advised within 7 days. They did give me options, I could take my clothes to a laundromat, which is 17 miles away where I love and they wont pay for my gas. Or I could get my own repair center but they would only cover up to $150 of the repair in labor cost and the part would have to come from Maytag/Whirlpool center. Then I would have to send my invoice to Maytag/Whirlpool for reimbursement. Now a company that cant get me a company to fix my dryer is going to send me my money back to me in a timely manner? I dont think so... Now on Monday after talking to the customer service I got a request to fill out a survey of my experience. I filled it in with details and today they called me from the corporate off in Benton Harbor regarding my survey. Well I finally thought I would have some action on this... Oh no was I wrong, they wanted to know why I filled it that way. I told them that this is a warranty issue. They did not offer me anything new but the same crap that the customer service offered. I now have a dryer less than 2 months old that I paid cash for. I am also 70 years old and on a fixed income as I explained to the Benton Harbor. It is quite evident that they could care less about customer service and their warranty. They do advertise on TV the Maytag repairman. Trust me this person does not exist and now I have $700+ item that I should put out on my lawn, take off the door and use it as a planter... and have a sign on THIS IS MAYTAG. DO NOT PURCHASE ANYTHING FROM THEM. I am so frustrated with this issue I want to scream.

Buyer beware. This machine has received several complaints. Not long after purchase, the washer started to stop during the fill cycle and give an error code no. This is supposed to be sure to overloading the machine. The other reason they give is something stuck item the baskets. Again not the case. Supposedly it must be a motor issue. Maytag was my trusted band. Our last Maytag lasted us almost twenty five years.I was excited to get this machine but disappointed with the lack of clean clothes, error codes, and noisy operation. My first clue should have been the one year only warranty. Thats how much they believe in their products. Ill never trust Maytag again. So sad that whirlpool should sabotage the Maytag brand and turn an otherwise great washer manufacturer into a piece of junk manufacturer. Dont buy whirlpool either as thats how much they care for customers.

Never waste your money and buy Maytag washer. Mine is XL large tub and has extra wash for extra clean. Dont waste your money. Never fills up with enough water. Almost everytime I wash I have to rewash the load because the clothes are still dirty, have soap spots and most of the time the clothes didnt even get wet. Horrible Horrible washer!!! My water bill has gone up a lot because I have to rewash the load so thats twice... I cant even use the XL tub because it wont fill up with water. Horrible product. Cant believe Maytag is still in business. They dont stand behind product. Called. Complained. They gave me nothing except for some free pods to clean a washer thats only 6 months old. Ive tried every cycle to see which one will wash the best. Still Horrible Horrible. Doesnt get anything cleaned. Here I thought nothing could get worse than a front loader? Well the Maytag is worse Horrible product. Dont buy. Dont waste your money. Try another brand!!!

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

Fire Hazard - poorly designed with vent at bottom of oven, Warped Drawer and Melted cabinet surface. Nowhere in the install instructions does it say not to mount above drawers. Whirlpool tried to blame dealer. Buyer beware.

The machine can clean even king size quilts, and clothes come out very clean. It is a front load and there are no problems with odors. There are many cycles to choose from. Cycles spin gently enough while getting out most of the moisture.

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.