I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

We bought a Bravos model in May 2010. Two years later, the machine started making noise during the final spin cycle. We finally called a repairman who came today and informed us it was a bearing in the outer drum. The cost for the part (the drum assembly) was $290, not to mention the cost for labor. Since we only got the original warranty, the service center at Maytag refused to help with the repair. We, as others who have had problems with Maytag, bought the washer because of Maytags reputation. This is why we have to buy extended service warranties. Companies make trash! What happened to the days when an appliance lasted longer than 10 years? Why cant we buy a good sturdy appliance without superficial bells and whistles? We have no idea if any other brand is better, but we will not buy another Maytag.

We purchase a matching Maytag washer and dryer set and within the first three months our washer began to give us error codes and would not wash our clothes completely on any cycle. It was repaired and we began to have the same issues within the next couple of months. This all happened within the first year. We called customer service about extending our service warranty due to the multiple malfunctions of this washer. We were given the run around and, quite frankly, the attitude that this was not their problem. I WILL NOT BUY ANOTHER MAYTAG PRODUCT! Thank you customer service for ensuring that I will not be a repeat customer!

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

I purchased a Maytag dryer several years ago, not a fancy one but just a plain simple dryer (model number MDE2706AYW). Thank goodness from the other complaints I have read I didn’t buy one that is computer controlled. The heating element has burned out twice, main thermostat and limit thermostat has burned out, and if you look close, it seems the wires are trying to melt or at least the insulation. Well, the insulation is melting. And the venting system is cleaned regularly so they can’t blame that. The last dryer I had lasted well over ten years with zero problems. I should have just fixed it. I’m sure I wouldn’t have spent as much money on repairs as I have with this one. You remember that lazy Maytag repairman that was on TV for so many years, you know why you don’t see him any longer? He is at my house repairing my ** dryer! You never, never hear me say this but the next dryer I buy will be made overseas. My last appliance purchase with any of these name brands on them: Maytag, Jenn-Air, Amana, Admiral, Crosley, Magic Chef, Performa by Maytag, and Norge.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

I purchased a Maytag front loading Epic z washer and I paid a great deal of money for it and now I have a broken part on it. We contacted the Maytag manufacturer and they have informed me that the part would not be available for up to two months maybe 6 months. I cannot afford to buy another washer, so now I have a broken washer and need to purchase another washer until the parts come in. I would not recommend this washer or dryer to anyone ever.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

What was shown on tv and the way it looked in home depot were much different when I got it home. The refrig. Is big as a bo car on the outside but inside nothing.

We can do nothing at the control panel even though the drum light will come on when the door is opened, we cannot turn it from the control panel. After a varying length of time, a fault code of F70 is displayed (which is not covered in the owners manual), the dryer can then be started by depressing the power button and all functions seem to be restored.

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

I purchased my microwave in 2012 and have had to have numerous repairs, mostly with the open/close door switch error. It is now 2018 and I see that the same problem is still occurring! Maytag obviously hasn’t read or doesn’t care that this problem has existed for years and they choose to do nothing about it. This past week when I had the microwave running, the beep went off indicating the popcorn was done but when I opened the door the microwave was STILL running! I thought it was a fluke but it happened again. Tonight the open/close door error once again appeared on the display. Having already had this repaired to the tune of over $150, not to mention the danger of a microwave running when the door is open, I called a mayday on the Maytag! I decided enough is enough and went out and purchased a new microwave... Obviously NOT a Maytag. The dangerous inoperable Maytag microwave is in the garage waiting for trash pickup.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

The bearings and motor went out in less than 3 years. The warranty good - the dealer I purchased from Siano Appliance gave me credit to purchase another Maytag washer - which I had to purchase an additional warranty for $320. The new Maytag is less than 5 months old - the motor has been replaced and waiting on a tech now to fix it. It would not come on. SO in warranties I have paid over $640 and am still having issues with the new washer. The first time I purchased a warranty for 10 year - when the machine was replaced I had to purchase another warranty for that machine - now if I have to replaced this one that will be an additional $320. IS this legal?

Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

I purchased the Maytag Bravos washer and dryer set one year ago, and have asked myself why ever since. The oversized laundry tub is what attracted me to the model, but it sure doesnt deliver for the money it cost. On normal settings, it doesnt use enough water for all the clothes to even get wet. After the load was complete, there were areas of my clothes bone dry, and obviously still dirty. I soon learned that the only way the washer uses enough water to get all the clothes wet and clean, was to set the machine on the bulky setting. This is the only setting I use now, but all of my clothes winds up twisted together, sometimes in one big ball. As for efficiency, that statement folks is a joke! Because I use the bulky setting, it uses much more water than a traditional washer ever did, and when the load is off balanced, it will go through another rinse cycle to try to even it out. This machine uses far more water and electricity than my old school set! I suppose if you dont get your clothes dirty, you may not need to use the bulky setting, but thats the only way I can wash my laundry with this machine. The old style set I had before this was Maytag also, and lasted about 20 years. I was more than happy to purchase Maytag again, but this set has been nothing but a disappointment. I dont plan to buy another energy efficient machine again, nor would I recommend this product to anyone!

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

Bought the Model MZD2766GEW and the MSD2454GRW side by side models of the Maytag side by side and the wide side by side from Home Depot in the year 2002 replacement appliances after a fire. For both units I paid $2526.92 dollars plus tax to put one in my kitchen and one in my basement. I was told by a plumber Maytag was the best, buy Maytag. It seems like from day one things went wrong. The ice maker kept building ice in the bottom of both freezers. The ice maker never worked right and would build up so much ice in the dispensing area, you would open the door and ice would fall all over the floor and you would have to take a knife to the shoot of the ice maker to unclog it. The drawers would freeze, the vegetables and anything in them, you had to keep the refrigerator temp to Zero and things would still freeze. Water eventually would leak all over the floor and I couldnt figure out where it was coming from. The freezers on the left but then water seem to be running to the right and out the refrigerator part. I couldnt afford to call anybody and the warranty was running out. I had 2 year parts and one year labor but at the time couldnt afford the service call charge. Eventually I was sent a recall notice for a compressor or such. I thought, Hurray, It will be fixed. Not at all. He replaced both those parts on both refrigerators and after he left it started leaking again. I called Maytag and they said, did he replace the part that was recalled? I said yes and they said They were not obligated to pay for anything past the recall. I should call and have the units serviced by a technician at my cost. If he says its the recall piece again, to call them back. Again I had no money to call a technician right away but when I did, he came to the house, told me it wasnt the recall and claimed to fix some kind of defrost sensor which cost $180.00 for the parts plus labor, plus service call and this had been a different technician than the first. He left and the problem continued to leak, freeze etc. In fact it seemed worse. I gave up calling and decided to deal with it hoping one day to replace but money problems happen and it is now 2014 I never could afford new refrigerators and have had to put up with the leak for all these years and continue to pick up and replace soaked towels everyday. In 2005 I disabled the ice maker which helped when I opened the door since ice doesnt fall out but both Refrigerators continue to make thick sheets of ice on the bottom and food is frozen into it so I cant use the bottom and when the buildup gets so bad it takes 2 days to defrost by shutting the entire unit off. All I can do is put my food in one freezer and refrigerator while the other defrosts. I also have turned the downstairs one off completely. Now as a second refrigerator I just dont trust keeping it on leaking also. I bought these units after a whole house fire and the last thing I want is another fire because Maytag just doesnt care but I cant afford new Refrigerators because these repairman and Maytag cant figure out whats wrong and fix the problem with this dangerous feature and I call it that because it seems to come with most of their units from when I bought the unit till now.12 years later people are still having the same problem with the same and copy cat units. Maytag, a plea goes out to you to recall and repair these units. The original recall did not work and like me a lot of people need to be redeemed for what you left go on and a lot of repairmen are ripping off people calling this problem what its not and stealing our money when you know what the problem is and can fix it. My plea is recall this problem or be responsible before God or who you believe in for letting it go on so long and the damage it may cost people. Maytag, people use to love you but youve ripped our hearts out and it will cost you in the long run.

Model #MDB8959SAS1 MAYTAG Dishwasher - purchased in 2014 at Home Depot. First we had to replace the rack adjuster, and after that another part broke. Finally, the electrical control board totally melted and smelled up the house. Fortunately our breaker switch worked and it didnt cause a fire. But Ive read other reviews of this happening with Maytag dishwashers where there was a fire. It now resides at the landfill.

I bought my fridge (Maytag French Door Fridge MFF2258VEW) in September 2009. It took forever to get it and when it was delivered, the door was dented so I had to wait for a new door to be replaced. The fridge stopped cooling just before Thanksgiving 2011. I had to throw out a lot of food. It was the circuit board and that was covered under the warranty. I noticed a couple of months later that the freezer was freezing up again and was worried that the fridge would go out again and in February 2012, they came out again and it turned out that the freezer had been put back incorrectly and the freezer gasket didnt fit right and thus, the freezing up on the circuit board. Now it is May 21, 2012, and I came home for lunch to find the fridge not working again! I cant get anyone out to fix it until Wednesday, the 23rd. Now we are in warm weather and I just went to the store and had a full fridge. I still have the warranty and will for another 14 months. I think if this continues to happen and when the warranty is up, we will have to replace this fridge. I can tell you for sure that it will not be another Maytag! What a piece of junk!

We bought a Maytag dryer and within two years the drum cracked. It will cost over $500 to repair it and then will the new drum be better? I bet not. Piece of junk.

My parents always bought Maytag and so did I. Ive experienced minimal problems in the past and have done my own repairs. My new MDB4949 dishwasher is GARBAGE! Imagine coming home and seeing water flowing out of the house under your back door! The water was coming from the kitchen across the kitchen floor and cascading down the stairs like a waterfall. I pressed the cancel button, nothing? Opened the door, NOTHING! Shut off the circuit breaker, NOTHING!Water continued to flow until I closed the supply valve! The dishwasher damaged my home! Six service visits later and still not fixed! 9 days out of warranty and still having the same problem! Customer service told me to hire a plumber to fix my plumbing problem with the dishwasher water supply! Thats funny because 3 other dishwashers (in the same exact place) had no problem with the water supply in the past 23 years? Two of them were Maytag!I never give less than a positive review but, this is outright FRAUD! The dishwasher has damaged my home on 2 occasions! Unless I want to stay home the whole time its running I cant use it? The customer service is pathetic at best. The control board issue is a scam by every company. Its all designed to keep you on a service plan and is a scam! Long gone are the days of the reliable rotary timer/control that lasted forever! You can thank everyone you know for not paying attention and letting this happen! I guess we can wash our own dishes by hand or comply with this obvious scam?

Do not buy this dishwasher unless you get the extended warranty. We purchased this dishwasher in Jan 2014. The first one delivered was completely busted up (which was probably the delivery companys fault for not handling it correctly). Then we had to wait for the replacement one to come in to get installed. In Sept 2014 the control panel stopped working. It was repaired under the warranty but it took several weeks for the authorized repair shop to be able to come out, diagnose, order part, and then come back to fix it. Now March 2015 (5 months later) we had the same exact problem with the control panel. The repair company was unwilling to order the part to bring with them even though they already had it in their records what we needed due to the previous repair. It was going to $300 to repair it since they only warranty the repair for 90 days. We decided to replace our 14-month old dishwasher rather than put any more money into it. Shame on you Maytag for putting out such a bad product - obviously this is a common problem. It is quiet and does a good job of washing but to have it take several weeks to get a repair done combined with having a problem that cost 50% of the purchase price to replace twice within a year of each other, absolutely not worth the money. Should have just spent the extra on a higher quality product. Will definitely get the extended warranty on whatever we replace it with.

Refrigerator - The freezer of the refrigerator would randomly leak on the floor. When I had it repaired on 12/30/14, at a cost of $253.97, the repairman showed me the defective part. He confirmed the online reports that the leaking was caused by a defective part. The defective part had been used because it was cheaper. Now the repaired refrigerator works well. Last month, the control panel on the dishwasher stopped working. According to the online reviews, this is a frequent problem requiring that a new control board be installed. The reported failure typically occurs after the one year warranty expires. My appliances are located in a second home so are only used about once a month. A salesperson at a different appliance store said that appliances usually last from 10 to 12 years. The four years of occasional use prior to failure is not acceptable. I would like to have Maytag repair the dishwasher at their cost. How do I get this to occur?

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

We purchased the Bravos XL in May 2017.. It quit working on April 30, 2019. Maytag sent me a form letter that basically said I was out of luck.. that sometimes things go wrong with a product or manufacturing. The fact that it wasnt 2 years old yet meant nothing to them. I would like to join or start a class action. This washer should not be sold.

I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

I purchased a 2011 Bravos top loader washer machine. Doing a minimal amount of laundry for 2 persons, the Bravos is in disrepair needing bearings and an inner and outer tub. I was told to purchase a prepaid service call for $350 that will cover repairs plus a mere 1 year additional warranty. The washer sounds like a jet plane, gives off fouls odors, has black tar like residue after each wash and clothes never smell clean. Maytag has no complaint process, except an online chat that tells you to buy the prepay. Maytag has dumped a lemon on consumers and arrogantly expects us to pay for their garbage. They are disrespectful, dishonest and greedy and dont deserve anyones hard earned money for their ill made products.

Do not buy a Maytag dishwasher with model # MDBH969AWB1. I bought this dishwasher last Dec. 2010. I could not use it for 2 weeks, because the door would not shut. The repair man came & fixed the door. Then when I actually got to use it and after it finished running the cycle, the tub was dripping with water all over--top, sides, door, bottom. I had to dry the dishes on the top rack, and I had to leave the door open for days in order for the inside to eventually get dry. The first thing I noticed about this dishwasher when it was installed was that it was smaller than my other dishwasher. I hate the design because of the way they have made the racks plus because it is smaller--it holds less dishes than my old one did. I could actually get almost twice as many dishes in my old one than I can with this one. Do they not think of asking the consumer about what they want in a dishwasher instead of going ahead and making something that is not functional?I am so frustrated with this thing; it has brought me to tears. I just today went to Sears and looked at their Kenmore dishwasher. It is designed more like my old one than any of the other makes out today. I wish I had checked this out, before I bought this Maytag. Weve always heard how Maytag is at the top of the line with no problems, right? Dont believe it. I will never buy another one. Whoever is designing these dishwashers need to go back to 1990 and take a look at how it was designed and then go back to making them like that. I loved my older dishwasher, and I wish I had never let them take it away. I wish I had taken the money I spent on this ridiculous Maytag and had my old one fixed no matter what the cost. I made a terrible mistake.If you have an older dishwasher and it has given you good service for years, I suggest you have it fixed and keep it, because you will not like the performance of what they are selling today. It does not matter what brand you buy, they are all designed the same. Just take a look and compare them. But if you buy, please check out the Kenmore. I dont know if the performance is better, but the racks are better designed. My old dishwasher was a Hotpoint. It was the cheapest one on the market, and it gave me the most wonderful service ever. The dishes were always very clean, the heating element was fantastic, and it always dried the dishes completely. I cant believe they would make a product like they do today and sell them for what they do. The heating element in them today is not as good or strong as what they used to make. That is why the dishes wont dry properly. You get way less than what you pay for. Thinking a new dishwasher is the way to go, think again. Please, if at all possible, keep your old one and have it fixed over & over again. I hate this dishwasher. What a joke on the unsuspecting buyer.

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

This washer ( MHW3505FW) leaks, is crazy loud, water wont drain, clothes smell bad after washing, defective drain pump, defective mother board. Only had 2 1/2 months and it broke. Maytag refused to refund me and Lowes refused as well. Thankfully I paid by credit card. Am disputing the charge. Terrible washer should be recalled. Many complaints on this washer. Very disappointed and upset.

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

I purchased a Maytag Dishwasher #MDB7749SBM1 as part of a complete kitchen remodel less than 3 years ago. Maytag was a great product years ago so I thought I would switch from GE to Maytag thinking that I had purchased a quality set that would give me years of great service! What a bad choice to say the least! This dishwasher has never dried the dishes completely with heated dry option. I never cared for the plastic latch and metal catch option either since I caught water dripping from the bottom since the door must not have been completely shut even though the latch was secure.Most recently, the start option on the flat control panel will not work. After opening and closing door multiple times I can get the start option to light up and run the cycle. Added bonus to start option not working correctly is that when the dishwasher door is shut, it automatically runs hours later with no human interaction. The dishwasher lights were lit up like a Christmas tree at 7 am this morning and running a cycle. Guess it thought the dishes werent clean enough. I am going to price out a board and determine whether I will throw this piece of crap in the dumpster and find a different brand! I HIGHLY RECOMMEND THAT YOU DONT BUY A MAYTAG DISHWASHER!

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

Purchased a Maytag Bravos 300 quiet series and am totally dissatisfied. I have a bandsaw, router and several saws in my workshop and by far my Maytag washer can drown them all out with the noise it makes. On top of all this it does not complete its cycles before it shuts off and if you try to restart it you never know where in the cycle it is going to start at. This may occur six or seven times before you are able to complete one wash. It may take a day to wash one load of clothes. Maytag should refund the total purchase price of this piece of junk!

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.

White clothes come out with some sort of grease stains on them and darks come out with a detergent white scum on them. I have to put them through twice to get the scum off and I have to scrub my whites by hand. So much for your new type washers. If I could find a washer with an agitator and water saver on it, I would buy it in a flash and get rid of this so called newest thing on the market. I have to put a cleaner through it every 2-3 weeks that costs me $10.00 for 3 pucks and having to rewash my clothes does not save water or time. There is a lot to be said for the washers that had water saver on them. First of all, I could open the lid during the wash cycle and add another item. (2) I could use the last of the 2 rinse cycles from my white clothes to start a load of dark clothes, that was truly a water saver and both loads were sparkling clean. Every women that I have discussed these new machines with (both front loaders and top loaders) say that you and other companies that think you have improved wash day for women have definitely not improved it but rather made it a nightmare. Absolutely hate this product. I hasnt given me a moments satisfaction since we spent the $1,000.00.

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

My Maytag refrigerator Model MFX2571XEMS has to constantly be defrosted due to ice accumulation in the bottom of the freezer. If not defrosted, water leaks out onto our hardwood floor. Maytag will not do anything to resolve this problem. We were told by a repairman that we have to defrost it manually to fix the problem. Yeah at least every 2 weeks. What a rip off.

I bought my Maytag dishwasher in February 2011. It seemed like a good model - basic functions, upper spray arm, stainless interior. Well this dishwasher has been all downhill since I got it. First it is cheaply made. The racks and plastic stoppers on the racks immediately started falling apart. The one year after we installed it the front control panel went out, rendering the dishwasher completely useless! The warranty had just run out! To my pleasant surprise, I received an extended warranty offer from Sears. Had the front panel replaced and it started working again.... but apparently it is a bad design and it is likely to happen again. After reading online I am not the only one with this problem.Now another year later we are having a the sprayer on the top and the back hose replaced..... (still waiting for sears to install). It makes grinding sounds, leaves white marks, doesnt clean.... it is a non-stop battle with this product. Upon calling Maytag, they said they could give me advice but cant pay for any parts or even give me a coupon towards a new product! I have tried everything with this dishwasher - fancy soap, cleaning solutions, jet dry... its not me, its Maytag! I will likely be in the market to buy another dishwasher next year because of all the issues, and it for sure will not be a Maytag.

Totally DISGUSTED!!!! Have owned my range for several years! Love have double ovens, however it is double the repair!!!! Every year we must have the handles replaced as the connection loosens and handles fall off!

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

Our range and oven are reliable and durable. Easy to clean and have lasted a long time. I do not regret spending a little extra money to have an appliance that has lasted a long time. The oven heats up at a standard rate. The self clean function is very thorough. I have a white set. I was worried they would stain with your typical spills that come along with cooking. However, They clean very easily.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

BROKE AFTER 3 YRS. Purchase a new Maytag model: MVWC425BW1 top load washer and dryer after just 3yrs of use. It failed and to find out this is a common problem with these new open drum washers. The bearings go out. Be aware do not purchase them and they also do not wash your clothes good, clothes just stay in same position and you have to wash 2-3 extra washes. It was going to cost 350.00 plus to repair so I purchased Speed Queen that has good reviews. Tech said that top load open barrel washers have been a nightmare.

This has been the worst washing machine I have ever owned!!! Purchased 3 years ago and this is the 3rd time the bearings dont work again. It make loud clanking noises. Then fails to spin at all. The first time it broke was the 1st year we owned it. It is sitting in our hallway and I can hardly wait for it to leave my house. Talked to the local appliance dealer and they never recommends these washers. I told dealer I must have gotten a lemon. He replied that it wasnt a lemon, that the machine tubs have gotten so much bigger and they have needed to upgrade the bearing system and are unwilling to do it. Dealer has highly recommended the Speed Queen. Based on the stellar reviews that is what will be coming to our house today. I can hardly wait. I know, its just a washing machine but frustration has overcome me. The Speed Queen has no plastic parts. We went with the knob style as opposed to the electronic push buttons. Less to go wrong. The warranty on the Speed Queen is top of the line, 5-year parts and labor. The salesperson didnt even try to sell me a warranty. No need to. Speed Queen stands by their product. I only recommend the Maytag Bravo XL if you dont have enough stress in your life.

We purchased the Maytag dishwasher model # MDB4949SDZ almost one year ago. Since the beginning there has been a smell to our drinking glasses when we put drink in them...smells like boiled eggs. We have always used Cascade dishwasher pods, but suddenly our dishes were being left with a gritty feeling film on them and I had to run them under water to rinse them after taking them out of the dishwasher. This model showed on Lowes website that it has a food grinder, but it cannot even get rid of a single kernel of corn that might get left on a plate. After a load is completely washed and you open the door, there is a strong smell of detergent. If you run an EMPTY dishwasher with NO soap it creates an abundance of suds like there is still soap all in the tub!!The repairman came out and called Maytag and they ran a diagnostic check on it and it said everything was okay. He said to run a cup of white vinegar through it and I did. It didnt help. Still lots of suds being produced when I run a cycle with NO dishes and NO soap!!! He said the food grinder doesnt actually grind or dispose of small particles of food, just grease!! What?!!!! We had to PAY $92 for the service call even though it is still under warranty just because the repairman and the Maytag guy on the phone couldnt figure out why this dishwasher is a hunk of junk!!!! Also, the top rack has clips on the side to lower and raise the rack. The outer sides of the top rack will only hold smaller glasses because these clips get in the way. I hate this dishwasher so much!!! My 18 year old Kenmore ran like a charm until Hurricane Harvey flooded our house. I will never buy a Maytag appliance again!!!

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

Code F51 showed up and my appliance repair man immediately said, I see this problem with the Maytag Bravos all the time. Its a control board and motor problem. He gave me a number to call to see if I could receive help through Maytag (Whirlpool), because its a major fix. He also thought that there might be a recall by now since there have been so many problems, but no. The Maytag customer rep was of no help. So disappointed in Maytag and the Bravos Washer. I will never buy another Maytag again!

About 4 years we purchased a dishwasher model # MDB7749AWM2 made by Maytag.The first part of Aug. 2015 it quit working. I had a repairman look at it and he said it was the control panel and he would order one. He ordered it and we waited a couple of weeks, no part. He called about it and they told him Sept. 9th it would be sent. Sept. 9 came went and no part. He called them again and they told him they had no record of the order. So he ordered it again in few weeks, was told it was back-ordered. This happened a couple more times and I told him to cancel the order. I would go buy a new one but not a Maytag.

Within the first six months the drive on the washer went out. Had to order it from another city cost over 200.00 for it then had it put in. The dryer works most of the time but now and then it just dont dry all the way.

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

Maytag Neptune MAH8700AWW and MDE9700AYH Washer and Dryer - Electrical overload to house circuit, multiple water pump replacements (Maytag would not sell rebuild kit with impeller and gasket or seal causing us to have to buy complete water pumps with mounts and motor.), electronic error readouts, odor and mold washing machine. The welds breaking on the drum causing possible fire hazard by filling case up with dryer lint fibers, around the electrical components, and air intake heater and also allowing metal fragments to get imbedded in the familys clothes. Also, Maytag Oversize Capacity Plus Quiet Pack Heavy Duty with Lifetime Tub.

My Maytag Neptune washer also has a problem with mold build-up and now the door lock assembly is totally gone. I was unaware of the class action suit or I would have joined. I am just disappointed!

I bought a Maytag Centennial Commercial washer, 3.8 cubic feet, Model # MVWC425BW on September 17, 2014. My clothes were never clean and barely wet. The machine took almost 2 hours to do a load of clothes and they werent even clean! I bought the 3-year extended warranty through Lowe’s. Three years and 8 days later the machine stopped working. Serviceman came out and told me the washer was fatally wounded. He said the transmission failed. He also told me the replacement part would be $400.00 and that it wasnt worth it. He said these machines are junk and Maytag has had all kinds of issues with them. So Maytag knows these machines fail and yet do nothing for their consumers. Maytag, you will only ride on your name for so long; consumers are catching on. Maybe back in my Moms day you were the go-to brand but Im afraid that ship has sailed. Ive always gone with Maytag but now I question that choice. I came on Consumer Affairs page to see what brand I could buy other than Maytag. Seems Kenmore gets high marks.

I wrecked on a bike, had surgery and in a wheelchair. I bought and had a Maytag dishwasher delivered from Beaumont Home Depot and this mdb7749sbw2 model never never worked. Home Depot told me I had to bring it back myself (Im in a wheelchair at the months that was impossible) and I called Maytag warranty. They sent a tech. He replaced a front power panel that didnt work. They sent out two more techs and they said use other soap Lemi Shine and the other guy said use Finish and turn your hot water heater all the way up. That never worked either. I have had this a yr and it just sit there and money in the trash. It makes me sick.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

Horrible machine. Purchased on 02/28/2014. I am 63 y/o retired housewife now. Machine used only for light washing, occasional king size sheets and weekly towels. I bought into the Maytag name, am so very angry that I did. Started a load at 1215 pm today... it is still sensing, washing, rinsing, spinning and then it starts all over again. Just unplugged from the power source, hopefully I can get the clothes spun out enough to dry!! Call and live chats to Maytag were frustrating to say the least. $400 plus Maytag service call to check out the machine not fix check out repairing would be extra. (I do not live in rural area, live 5 minutes from downtown Jacksonville FL!!!) Independent Repairmen will not touch this Maytag Model (cannot say I blame them!!). DO NOT PURCHASE A MAYTAG PRODUCT. This is a horrible company lacking in integrity, honesty and fairness. They sell shoddy, inferior products based upon past history.

I have a Maytag Neptune (model number MAH5500BWW and serial number 85981207AE). On February 22, 2012, the washer started smoking and a burn smell was apparent. Fire department was called. They pinpointed issue to the washer. On February 23, 2012, I spoke with Brenda from the Safety Department. She prioritized a diagnosis from a local certified technician. On February 24, 2012 , the technician diagnosis was defect motor and control runs hot after load. Then Lorna from the Safety Department stated they will not cover part/labor.Machine is

Maytag model mfd2561hes French door stainless steel purchased in June 2005 has been the worst appliance purchase ever. After 1 year warranty expired, icemaker and water dispenser stopped working. Was told by repairman to thaw the tube for water dispensing with a hair dryer. Are you kidding me? Why should I have to pull a huge refrigerator out from wall and put the hair dryer to it to thaw out the water line when I need water? What is the convenience to that? Cant buy fresh vegetables as it will freeze before I can use it. This is the worst appliance ever. Dont buy Maytag products. Maytag doesnt back products like the old days when they would last 20 + years. Cant last even a year anymore. Sad!

We bought a pair of Maytag Bravo MCT washer and dryer on May 30, 2011. On April 30th our dryer would not turn on. We called the Maytag service where we bought our machine, and were told it was a fried motherboard and would cost approx $600 parts plus labour. For a machine to last less than three years is very unreasonable. Maytag used to have such a good name. That is why we originally went for this brand. We were told by the service tech, that if we opted to buy a new replacement machine they would waive the service call charge. Is this how Maytag keeps selling units?? We bought the higher end units thinking that they would last 10+ years but now it seems Maytag has designed their machines that are disposable. Tisk tisk Maytag. No wonder your service men are lonely... Your sales staff are too busy reselling to loyal customers. Well, you have lost customer with us. We are going to Sears to buy a new dryer made by GE and will sell our Maytag washer on Craigslist and replace it with the matching washer from GE.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

First off, the drum split apart on the dryer. The drum part was not in this country, so instead of going ahead and replacing the clothes dryer, they told me to hang the clothes outside for six weeks or whenever the part comes in. That was three months after owning the piece of junk. I was having a bad day already, so I basically completely lost it. Im surprised I didnt get arrested for that. I wont ever lose my temper like that again. The clothes always smell bad, and sometimes really bad. Now, I find out that both washer and dryer could cause a fire. They are sending us a couple of really cheap GFCIs to keep them from a liability issue. Maytag is the absolute worst!

My Maytag dishwasher is 1.5 years old and wont start. The Maytag call center said they couldnt help me except to sell me a service warranty for $269. Then she wanted to argue with me when I asked her to pass on my dissatisfaction with their products to her supervisor. I thought Maytag was a good product. For what I pay for parts and labor, I can get a new dishwasher. She said do I expect not to have any problems with that dishwasher. I will never buy anything Maytag again. They do not stand behind their products. Plus, it sounds like many people have had the same problem with their Maytag dishwasher. This part is defective. (I am assuming it is a control panel problem.) Since corporations are people now is there someone I push into my dishwasher so they will fix it. LOL.

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

Maytag is the worst dryer ever purchased. We bought it in 2019 and the heating element broke. When I contacted Maytag directly, they said, nothing they could do. Really?? A major part was defected and there was nothing they could do! Its very sad when a major company that you purchased from shuts you down with a defected piece in their dryer and they chose not to help out the consumer. Shameful! I will NEVER purchase another product from them again...

After having issues with bearings in a front load of another brand, we decided upon a top load Maytag. We have had it less than a year and we are not happy with the performance. We are using more detergent because the dispenser seems to be bottomless. Only the front of the little pull out drawer is visible and it never seems to reach the fill line when adding liquid detergent. There is no quick wash cycle. Not everything needs a cycle of nearly an hour or more. The spin cycle does not remove nearly as much dampness/water as our previous frontload. The drum is deep making it difficult to retrieve small items such as socks. My biggest disappointment is finding lint residue on the clothing and it remains even after an extra rinse. This is especially visible on dark clothing. Even the lint filter in our dryer fills up much more quickly than before. After researching, I found that others complained of this same problem.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

My mom decided to splurge on a new Maytag Bravos washing machine and matching dryer thinking that at age 80 the machine would outlast her. But no. After 4 years and just past the warranty, the timer started going crazy. The repairman recommended a $250 motherboard and $90 pump and $500 labor (yes he is next on my list) and it still does not work. I WILL get her money back for the repair and we will NOT be getting a bravos to replace it.

I bought this Maytag dishwasher model mdb6709awq1 from Home Depot that installed it; they did a good job installing for a fair price. My gripe is with Maytag. I have owned a Maytag dishwasher since 1977. Back then it was the best you could buy. Since Maytag sold out to Whirlpool to save being bought by the Chinese, the design of the dishwasher has lost or gave up their unique design that made it so good and dependable. The inside of the rack/drawers has been totally changed. It used to have fold down racks on each side of bottom rack that was great for coffee mugs, small bowls/containers, and they came out sparkling clean. The utensil basket was centered front and again the utensils came out super clean. Maytag sold their soul when they sold out to Whirlpool. Dont know if that was part of the deal that they give up their unique design or why did they change the rack design. I wish I still had my old Maytag from 1998 that yes, worked without a problem, then I sold the house with the dishwasher. Why is it that so many appliance makers have taken dependable workhorse designs and phased them out? What is wrong with an appliance lasting for years, decades without problems? Only thing I can think of is that they wont make millions every year as they only would sell so many a year if they are dependable as they wont need to be replaced.

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

Maytag Glass top model #MER8600DHO. I bought it because it got good consumer reviews. This is supposed to be a self clean oven but the steam system in this model is not very effective. It doesnt clean the oven. Would never buy a range again with this oven cleaning system. I wanted to try a glass top stove but wish I hadnt. It is harder to clean and the glass scratches. I really dont like the self clean oven system in this stove - it flat out doesnt work and it takes a lot of elbow grease to clean the oven. The oven however seems true to temperature and does a good job. Overall I am Ok with this stove but wouldnt purchase a glass top again.

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

I purchased a Maytag French Door Refrigerator in July 2011 from Lowes online and had it delivered on August 16, 2011. In September 2011, I could not get the ice maker to work. So I called Lowes and they called in a repairman. He came and replaced a part to fix the problem. I dont have any complaint with his work but here it is, October, and the ice maker makes maybe four ice cubes at a time on a good day.I am really disappointed with this product and according to their commercials, I would like to know which of these techs are setting around doing nothing, maybe he could come and fix my fridge once and for all. I would sure find it difficult to recommend any Maytag appliance as a result of this mess. I could call a repairman myself, but I was under the impression thats what a warranty was for. According to Lowes we are required to call them and they will schedule a repairman or the warranty isnt any good. I replaced a GE French Door with this Maytag, I sure am sorry I chose this Maytag.I know an ice maker problem is minor compared to some of the complaints on this appliance, but when you pay good money for a product you have every right to expect everything about it to work. Im just wondering where these appliances are actually made?

I bought a Maytag washer and dryer in Cookeville TN. In 2018. After a year it quit. The service man from the authorized dealer in Cookeville could not repair it. After numerous calls Maytag sent a service man to repair it, this took about three weeks. This washer is a Maytag industrial, it has a 5 year parts and labor warranty, and 10 years on the motors. Now it is out again, after calling Maytag, and holding on the line for an hour, finally I had to chat with someone, and they set up an appointment for about 3 days. So service company call now and says it will be another week before they can sent someone to look at it, and another week to get the parts. They also questioned my warranty. I gave high dollar for this washer, what’s happened to Maytag?

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

The Bravo HE Washer was a cheap piece of garbage and I am very surprised Maytag put its name on it. It broke down exactly one year after the warranty went. It did not ever clean clothes properly and all stains remained even when you spot clean first and double rinse. Maytag basically ripped us all off and somebody should start a class action lawsuit for this thing they call a washing machine! What a joke! I wont repair it. It will just fall apart again. Im not stupid. I know this is how they pay their employees doing house calls! So now, I have to go to garage sales and look for one made in the 1970s because that is when machines were made in the USA and things were built to last, not this crud. Maytag should be ashamed. It is time for them to close its doors. Sorry but its true. They are just crooks now selling crud that falls apart! They owe me a full refund.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

I had a Maytag washing machine replaced under warranty back in 2011 via Maytags Extended Service Plan. This took me several months to get done because of back and forth issues with Maytag not wanting to honor the replacement. Executive Support had to get involved after I wrote a complaint on this site. When they replaced this, they sent me forms to extend my warranty, which I did. They never changed the model or serial number so Ive been paying for 2 years now for an extended warranty on a machine I do not own.The new washer broke and I called in for service on 11/18/13. Active Appliance was sent out, said it was an easy fix but they needed to order a part. On 11/20/13 they contacted me to tell me I needed to speak to Maytag because my Model/Serial didnt match with my warranty records. I double-checked these and called Maytag Extended Service and was told that I would need to speak to sales at 866-730-6094. I spoke to someone named Lindsey there who told me that I would need to send a letter in to cancel my policy and request a refund for the 2 years Id been paying for a non-existent unit and that they could start a new policy for me and get a service order in without issue. My call was disconnected during this and when I called back, I was told to call back in the morning to get back to Lindsey because the office was closing and they couldnt do callbacks.I called back on 11/21/13 and spoke to Sam who verified that the letter was needed to cancel and refund but that I would have to pay for the repair to the washer myself and theyd tack on the cost of the new warranty onto that bill so Id be covered AFTER THE FACT. Because the unit wasnt covered under warranty, Id have to cover the costs myself and it had been MY responsibility, not theirs, to make sure that the correct model/serial was on the coverage.Maytag sent me the forms and I would expect them to have added the new information on it...not send me forms with my original washing machine information. Especially as this had been escalated to Executive Support and the person I dealt with there had gone over everything to make sure it all got handled in a satisfactory matter. So for now, Im waiting for a callback from the original rep, Lindsey, but Maytag tends to Stonewall and not return calls so Im dreading how long this entire process is going to take and cost.

I bought a Maytag dishwasher from Home Depot in February 2012, $700. After a few months, the buttons stopped working and the machine was unresponsive. I called Home Depot and they fixed it under the warranty. This continued to happen every 2-3 months. After a year of dealing with this, the warranty expired and I had to purchase the manufacturer extended warranty with Maytag, $240 for 5-years of coverage. The problem continued, and every few months, the thing would stop working and I would have to call for service - 2 to 4 weeks without a dishwasher waiting for service appointment then parts and another appointment for the repair.Perhaps my machine was just a lemon. I dont think they make that model anymore. Heres the number so that you can avoid a three year headache of a machine, MD87749 AWM2. I will say that after MANY agonizing phone calls with warranty company, after 2 years of ongoing service calls, they eventually issued me a check to replace my lemon.

My original GE dishwasher that came with our house finally crapped out after about 8 years of use in 2007. Bought a Maytag from Home Depot for around $400. Dont remember the model number. It worked okay but then in the middle of 2010 we got a letter in the mail saying our machine was being recalled because the heating element might catch fire (!!!). The recall gave us the option of getting it fixed or getting a $150 rebate. We chose the rebate option so we trashed this dishwasher and went back to Home Depot to buy another one.We found a very nice Maytag with the stainless steel tub and the racks with the lifetime warranty against corrosion (which was good because our previous Maytag had started to leave rust on our dishes because the plastic on the tips of the rack tines was starting to come off), model #MDBA979AWB1, serial #FY2501885. The one we found was a no-box display model but it had all the accessories with it and still had the factory warranty. We got it for just over $300 and with our rebate applied we were out the door for under $200 including tax. I installed it myself and didnt have any issues for quite some time. My wife and I were both very happy with how clean the dishes got!Now, last night the dishwasher wouldnt start. I checked it out this morning, made sure it had power and was able to get some lights on the control panel to light up but still couldnt get it to start. Looks like Ive been victimized by the control board as most of these complaints have said. I guess I should consider us lucky since ours seems to have lasted longer than the average 18 months to 2 years. Will be contacting Maytag and Home Depot to see what they can do but after reading all these negative reviews Im not hopeful.

My Atlantis dryer has never been able to be used on more/less dryer settings, I have had 4 repairmen repair my dryer 3 were while dryer was under warranty to fix the same thing 3 times wiring 4th time, anyway last repairman said my More dry wont work because I never had a sensor installed in my dryer and there is not a place for one so since 2005. Ive used timed dry only or my dryer runs all the time. I am concerned the first 3 repairmen never caught this. I should not have to be responsible for this either. Please have a manager contact me and have them check into my Atlantis Maytag dryer bought in 2005 and all the repair slips sent to Maytag.I used Green Yates in Joplin. Pretty sure. I thought I just had to live with it they would put new parts on I think timer, thermostats anyway can someone tell me for sure or inspect for yourself. I am single and dryer never used that much. Concerned Consumer, Nancy **/ Nancy ** as that name had front loader set from Maytag that I was very pleased with but sold with home in KC area, wish I had that set again I was very pleased .Thanks for your time.