Disturbing that this product made it into production. I have the matching dryer too, and its just as bad. First the washer rolls up clothes into a tight ball better than I could do if I did it by hand. Then it spins, setting the wrinkles in thoroughly. Then, even though I shake out the clothes before putting in dryer, after the clothes come out of the dryer (without letting them sit in there) - the clothes look like someone drove over them with a car while they were rolled up in a ball. Bonus: the clothes dont even get dried. Ive watched the clothes in the dryer, the drum is designed so the clothes stick to the outside of it and go around, they never actually tumble or get any air circulation. What a disastrous product.

We purchased a Maytag Bravos set in 2011. The dryer works great, but the washer not so much. Every load of darks comes out with soap scum all over. I use the HE detergent and most time use less than what the load should have. We have soft water and I also use softener. Ive also tried up to 3 extra rinse cycles and a smaller load size and still have soap scum all over. Im sure the light colored loads come out same, just cant see it. Needless to say, very, very upset with this washer. I, too, will never buy another Maytag product, nor will I recommend one. Had our yearly maintenance check the other day and the service man couldnt give me the reason its doing this. So, so disappointed in this product!!

I purchased the Maytag Bravos washer and dryer set one year ago, and have asked myself why ever since. The oversized laundry tub is what attracted me to the model, but it sure doesnt deliver for the money it cost. On normal settings, it doesnt use enough water for all the clothes to even get wet. After the load was complete, there were areas of my clothes bone dry, and obviously still dirty. I soon learned that the only way the washer uses enough water to get all the clothes wet and clean, was to set the machine on the bulky setting. This is the only setting I use now, but all of my clothes winds up twisted together, sometimes in one big ball. As for efficiency, that statement folks is a joke! Because I use the bulky setting, it uses much more water than a traditional washer ever did, and when the load is off balanced, it will go through another rinse cycle to try to even it out. This machine uses far more water and electricity than my old school set! I suppose if you dont get your clothes dirty, you may not need to use the bulky setting, but thats the only way I can wash my laundry with this machine. The old style set I had before this was Maytag also, and lasted about 20 years. I was more than happy to purchase Maytag again, but this set has been nothing but a disappointment. I dont plan to buy another energy efficient machine again, nor would I recommend this product to anyone!

I bought a Maytag Neptune top load washer in 2002. It worked fine (with the exception of smelly clothes) until October 2011. Since then I tried replacing two new clutch assemblies, a new outer tub and bearings. What we were just told this week: it needs a new spinner. Finally throwing in the towel and taking the $500 credit from Sears and buying a new washer. And I can guarantee I will never buy another Maytag product again!

We purchased a Maytag front-load washer and dryer in October 2010. In March 2011, all bearings and the drum needed replacement. In July 2011, the pump needed service and now in Sept 2011, we were told a new drum and bearings are needed again. The washer is still under warranty by Maytag. We contacted Maytag to ask for an exchange or a refund but we were told that it wasnt possible.

My 2.5 year old hood range microwave stopped heating. I called repair guy, he charged $115.00 for barely a half hour and said he tightened a part and it should be fine OR the part would need to be replaced. Guess what!... That night microwave is still not heating anything. Dinos Appliance Repair is responsible to repair but Maytag doesnt stand behind its product. How do I get my money back when a repair doesnt repair anything? I wont buy Maytag again or GE.

I bought a Maytag Bravo washer and dryer 18 months ago. While taking clothes out of my washer, I noticed that the plastic collar above the washtub was shredding around the edges. I called the manufacturer about it. Because it was more than 12 months old, they refused to do anything about it. I feel that shouldnt happen so soon after purchase. Im a single person and dont do that much laundry. The piece should be made of something more durable. I will never buy another Maytag product. Is there anything further I can do to pursue this?

We purchased our home in late 2010 and was excited about our HE front-load washer (and dryer). Immediately, we noticed mold on the rubber boot, and the smell was horrible. We ran the washer with Affresh several times and left the door to open when not in use, and that seemed to help. Then most recently, the washers been shutting off mid-cycle through normal wash setting. I used to pound the washer out of frustration, and that seemed to get the machine working, but now it doesnt work at all. We had a repairman come out, and he charged us $94 to basically remove debris from the drain hose, and he told us that if the washer fails again, wed be looking at an expensive repair cost pertaining to the central control unit. We had a second repairman come out and replace the central control unit. It worked while he was here, but now its messing up again, shutting down mid-cycle. I have to unplug the washer for hours, replug, put it on rapid wash cycle (and hope it doesnt fail), and if it fails, then unplug, wait, put it on spin cycle... Its aggravating, and were looking at $300 to $400 in repair costs. Our repair man says front loaders are a nightmare (and he still has his non-HE washer from the 80s, and its still working). Our washer is Maytag Epic Z, model number MHWZ600TE00. Avoid front loaders, and definitely Maytag or Whirlpool front loaders. Well need to shop around for a new washer, an old-fashioned top loader this time.

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

I purchased my 10kg commercial Maytag dryer in March 2015 and started using it in May 2015. Within two months the heater had broken. I contacted the people I bought it off and it turned out I had to contact Whirlpool. It took them 8 weeks to get my dryer going again. The dryer broke down again in November. This time it was a sensor. Again I had to contact Whirlpool, it took them three weeks to get it going again. Being a care home the dryer is essential to our business. We were led to believe when we took out the extended warranty that the dryer would be fixed within a week. I will never purchase a Maytag again or anything to do with Whirlpool.

I purchased Maytag Centennial Commercial washer and dryer eleven years ago. Both are still going strong. It has been a great purchase. Only issue is a couple of stains have appeared on outside of appliances.

We are on our 2nd Maytag washer with the 1st being a top load with agitator and the second without. Both were also bought used. The 1st one broke after I was cleaning it so totally my fault but the second one the door lock broke. Aside from that they do wash clothes well and but I do wish there were more or different cycle settings. Overall they are good machines for out price. (Being used that is.)

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

Good deal, recommended by dealer friend. Front loaders, high efficiency, 12 years or so. Finally needs new bearings on the washer. Replaced electronic board 5 years ago. High repair costs would be the worst which is related to low-quality construction. I expect my next pair to last as long as the last 1. Full size, not stackable but oversized drums. Relatively low water usage, lots of different settings for different loads for washing and drying, automatic water level and wrinkle guard.

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

Maytag MHW3505FW Washer and dryer were purchased 13 months ago. I purchased and spent $2,000 because the Lowes salesperson and the stickers on the machine said they had a 10 year GUARANTEE AND commercial quality/technology. Exactly 2 weeks after 12 months the washer started flashing erratically when I was able to turn it on. Wouldnt react to any of the touch controls and stopped working. Called Lowes who told me because I hadnt bought an extended warranty they would do nothing. When I told them I was told a 10 year warranty was in place they said they only cover a year. I was told to call Maytag. Maytag said the 10 year warranty only covers the steel drum and motor! Nothing else is covered after one year. I was offered an extended warranty for $600. Not something I will be doing. I will replace with non-computer washer and dryer and will NEVER BUY MAYTAG again. They should be sued for false advertising.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

My mom decided to splurge on a new Maytag Bravos washing machine and matching dryer thinking that at age 80 the machine would outlast her. But no. After 4 years and just past the warranty, the timer started going crazy. The repairman recommended a $250 motherboard and $90 pump and $500 labor (yes he is next on my list) and it still does not work. I WILL get her money back for the repair and we will NOT be getting a bravos to replace it.

Maytag, you are still trading on your good name but that will not last! I owned a Maytag, agitator style, for 20 years and it was still running just fine when we built a new house. I thought it would be wise to buy new appliances for my new laundry room so I chose the beautiful and expensive Maytag Bravos XL. I regret that decision. The washer lasted 4 years and began to have problems draining last week. The liquid that stayed in the washtub until the repairman could get here was so foul smelling! He came back today to replace the drain pump and now the washer is showing that the interface and CCU are not communicating. So now we are ordering another CCU and I hope this fixes the problem. I agree with all of you who say you will NEVER buy another Maytag again. Maytag, are you listening?

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

I purchased a Maytag dishwasher 15 months ago and was told the control panel is bad. It would cost me $120 to have someone look at it. I might as well buy a new one by the time the parts are added. I called Maytag and they said that there was nothing they could do for me since I was three months past my warranty. Meanwhile, I see all of these complaints about the same problem and Im wondering why there has not been a recall on this. What does it take for that to happen? I will never purchase a Maytag again! Their customer service leaves a lot to be desired. All they do is apologize like its programmed in their heads. This feels like a fraud!

I purchased my Maytag Bravos from Lowes in early 2014. A few weeks after the motherboard fried and Lowes replaced it with a new one. Within my 1 year warranty the new machine had another fried motherboard. Maytag replaced it for free. Now less than a year later the motherboard is fried again. Needless to say I just purchased another washing machine. Definitely not a Maytag. Now I just have to deal with a dysfunctional piece a junk for a few days until I get my new one. After reading all the complaints on here and other sites, Im very disappointed with Maytag. These machines are obviously lemons and any good company should recall them. Mine will be going straight to the junkyard. I have no interest in having a washer that breaks down every 10 months. Definitely the last thing I will ever purchase from Maytag.

We purchased a Maytag Refrigerator-Freezer from Home Depot, in July, 2014. The first two months we had this appliance, it would not make ice (we purchased one that had an ice maker it the freezer!). After numerous calls to Home Depot and about 7 service visits, the service company gave up trying to get the ice maker to work, and instructed Home Depot to give us a replacement refrigerator. The new one came with an ice maker that works some better, but still very slow in making ice, and the new refrig makes a grinding noise every time we open the door. The Maytag Company, whose service people never have anything to do, say this is a cosmetic problem, and they refuse to fix it.Have been in consultation with Whirlpool Company (who bought out Maytag I assume), trying to get the appliance repaired... or at least put an end to the grinding noise. We paid a lot of money for this refrigerator freezer, and have had nothing but trouble and issues with it. If you are thinking about buying a Maytag refrigerator -- Dont!!

Purchased Maytag Dishwasher Model MDB7749SBW3 in April 2014 along with other Maytag appliances to go into our home in the Georgia Mountains. Purchased Maytag for 2 reasons: 1. American made 2. Reputation. Bottom line, after just 2 years the dishwasher has failed. I prewash by hand everything that goes in. First the normal cycle stopped working. Then lights on front panel would randomly turn on and dishwasher would turn on by itself, and run for hours. I suspect this could be a fire hazard. I have tried front panel resets, cycling power, etc. Nothing works... It is really sad that American products are third world. I will replace the board myself in hopes of getting another couple of years out of it. No more Maytag for me. Rest assured every time I see someone in Home Depot or Lowes, looking at Maytag appliances, I will go out of my way to warn them.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

I chose Maytag because they received a good rating from Consumer Reports. I liked that they were for extra large loads however now that Ive had them for 12 years I know the large loads are no more than my old Kenmore washer and dryer. The real deal breaker for me is the size of load that you can actually wash. I was hoping I would be able to wash a blanket without worrying about the washer going off balance. My washer and dryer are Maytag although I dont know the model number. They are full size but the extra large load is not extra large. The knob on my washer broke and Maytag wanted $15 for a plastic knob! I found it on eBay for $3. The washer goes off balance too easily.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

After speaking to a Kim today... Im more than angry. The control panel on my dishwasher is broken. Had repair come out and they told me a few months past warranty. Kim tells me the only thing still under warranty are the racks?! Im extremely angry at the poor service we are receiving but pleased as we have cancelled the washer and dryer (Maytag). If youre thinking of going Maytag or Whirlpool, cancel! Not worth the headaches or cost.

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

All in all I have liked my electric range, but I have 2 issues that I am having trouble resolving. I bought the range in 2003 and to find the model number I have to pull the range out from the cupboards on each side which would be extremely difficult under the circumstances. The reason I want to get the model number is so that I might find replacement parts for the doors edging that has flaked and rusted and is quite unattractive.

We purchased a Maytag Top Load 5.4 cu ft efficiency washing machine. May 2019. It was making a funny noise already mid October and we had 8 parts replaced. After that it completely stopped working. We have been without a working washing machine for 2 months now. The technician has been to our house 4 times. When he came on Dec 31st to replace the mother board, that didnt solve the problem. He says the washing machine can not be repaired. We have been fighting with Maytag Canada and Lowes since the beginning of December. Neither company cares. We will never own another Maytag product. The company are crooks.

Unless you’re doing laundry for an army don’t buy the Maytag commercial washer MVWP575GW. I should have gone with my original choice but my husband was concerned with the durability and warranty hence why we purchased this washer. It’s just the 2 of us and I frequently use the delicate cycle. Unknown to me at the time you can not adjust your water level so if you’re washing delicates plan on wasting a lot of water unless you only wash your delicates once a month. In my opinion delicates are undergarments, blouses, etc. delicate cycle in “deep water wash” only. As far as we can tell the wash cycle at its longest is 8 minutes which I guess for commercial grade is probably correct. However there is a presoak option that I don’t the believe does the work of a longer wash cycle. If you have to do a quick scrub on a piece of clothing as the washer is filling up you can not do this as everything stops once the lid is up.Last but not least the washer is loud it sounds like it’s going to break down at any minute. I’m sure many of the issues people have with products today are due to government regulations. I’ve tried contacting Maytag customer service on numerous occasions to see if I’ve been doing something wrong even though I’ve read through the operating manual several times, I’m currently on hold for 20 minutes. Doing the laundry has never been the highlight of my day but I never minded it until now. I absolutely dread it now. My suggestion would be if you like the features on your current washer, spend what you need to to get it working properly which is what I wish I had done with my 23 yr old washer. Worst purchase I’ve ever made!

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

My Maytag Neptune washer was purchased last October 2010. In the past few months, the washer has been making a loud noise when spinning/washing. I had a Maytag repairman look at the washer, and all the barring, etc. needed to be replaced, which would have a cost of over $450.00! I am very upset with this outcome and just looked into it and found that this washer had recalls that the consumers were not properly notified about. The lack of recall communication is inexcusable, especially since I even went as far as to buy a 3-year extended warranty and still was not notified.What really set this situation was that the repairman suggested to not buy a Maytag washer and he added that it would not be a problem since Maytag has been purchased by Whirlpool and that the Neptune washer played a part of the ending of Maytag! This whole situation has really put a bad taste for any Maytag product, and all of my major appliances are Maytag as well as the dryer I just purchased a week ago, before I knew about all of the disappointment of Maytag. I am sure the response I will be getting will be as good as the notification of the recall, which will be nothing. Thanks!

I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

Purchased a new Maytag washer (MAH5500BWW) and matching dryer along with the pedestal that they sit on in late November of 2003. Spent well over $1900.00 for everything including the delivery charge. I noticed the build up of mold/mildew inside the washer starting in early 2005 but cleaned it every week or so and it seemed to go away. As time went along the mold/mildew smell got stronger even after each cleaning that I did with bleach. Nothing seemed to help.It wasnt until 3 days ago when I had my dryer vent cleaned by a professional company that the technician looked over at the washer and said You know that washer was recalled and that there was a class action lawsuit against Maytag about mold/mildew issues involving that model. He opened up the washer door and looked and was shocked. He told me that he himself had the same Maytag model washer and was notified by Maytag years ago about the class action lawsuit. He told me that he had received what he called a buy back check from Maytag. I wondered why I had not been notified since I had purchased both units new and registered both with Maytag after my purchase.I decided to do a search for my washer model number and looked for mold/mildew issues and was shocked to find thousands of complaints involving this issue with this model of washer. I then called Maytag/Whirlpool and this is where the fun begins. I called and explained to the customer service rep at Maytag/Whirlpool what the problem was with my washer and asked her why I was never notified of any recall or class action lawsuit involving my washer. After thinking for a minute or two she says that she is unaware of any problems with my model of washer and asked me to recheck my model number. I do this and again she says that she is unaware of any problems associated with my washer. I explain to her about the thousands of complaints on the internet about this mold/mildew problem and she then says I shouldnt believe everything I read on the internet.At this point I ask to speak to her supervisor which she says she transfers me to and the fun continues. The supervisor then tells me that the customer service rep whom I was speaking with is new and doesnt remember the issues with my model of Maytag washer but she herself does remember the issue of mold/mildew build up inside the washer. I ask her why wouldnt this issue of mold/mildew in this washer be in your system for this rep to be able to refer to? She then says that since this issue was so long ago its not in their system anymore. Huh???She asks me if I was part of the class action lawsuit involving this washer and I explain to her that I was never notified of any such lawsuit so I couldnt have been part of it. She then says that Maytag has since settled this issue long ago and since I missed signing up for the class action lawsuit I was just out of luck. Somehow its now my fault for them not notifying me about the class action lawsuit years ago!She then offers to send out a repair person to look at my washer and to look at the mold/mildew problem. I ask her if the service call was free and she snickered and said no, why would it be free? I tell her I thought it should be free because I paid nearly $2000.00 for these machines because I was looking to get the top of the line machines. Now I have a mold/mildew infested Maytag washer that smells and looks so bad its a assumed health risk. She again tells me that the service call will not be free and asks if I want her to schedule it now. I quickly decline!She then tries explain to me in some odd fashion that I should be happy that I got 10 years of service from my washer/dryer and hoped that I would continue to purchase Maytag. What??? Are you crazy woman!? Now its me who is laughing at this point. I almost say some very bad things to her but better judgment takes hold and I just hang up. Now you have heard my story and Im now looking for another washer/dryer so I can remove this health hazard from my home. I will never ever buy anything that has a Maytag/Whirlpool named attached to it.

I bought a Maytag dishwasher (MDB7749SBM) and 1 yr and 4 months the control panel went out and all Maytag would do is tell me that they will pay for the parts, and I have to pay for the labor. I remember when Maytag had the best Warranty on their appliances. I am very disappointing with paying for labor. They also offer an extended plan of $269.00 for a year. What a joke!!!

So I get the matching set washer and dryer when I moved into my new house. I thought I was getting a nice set. I paid around $1600 for them with the sale they had going on. From day one the washer wouldnt get a full size comforter wet on the bulky cycle or heavy duty cycle. I even tried the extra rinse cycle on both as well. I would have stop it mid wash and rotate the comforter. Clothes wouldnt settle sometimes and would leave the top dry and bottom soaking wet. In the first year the lid latch started going bad. So sometimes you would go back to realize the load hadnt even started. Clothes dont get clean no matter what setting you use. It is the worst purchase Ive ever made. The dryer was ok until its almost second year. It just stopped drying it seemed. I cleaned EVERYTHING! No effect. It takes 3 full cycles at minimum to dry clothes. I cant understand why these machines arent pulled from the market or recalled because they are junk.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

I have filed a class action lawsuit against Whirlpool for their faulty control panels in their Whirlpool and Maytag dishwashers. Please contact my attorney, Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 and let them know if you own or owned a dishwasher with control panel failures.

We had a Whirlpool dishwasher for 24 years, and when it was time to purchase a new one, I did a lot of research before choosing our Maytag. Reviews by other consumers who had purchased dishwashers was very helpful in making our decision, and we have had no problems in the almost 18 months that we have had this dishwasher. It is very quiet. It washes and dries the dishes with no streaks, although I wash off the dishes before loading them. It provides 5 cycles and 4 options and lights blink, when the washing and drying cycles are complete. I would recommend the Maytag, Model #MDB4949SHBO wholeheartedly.

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

I have recently purchased a washing machine. Within the first week I was calling a repair person to fix it. I HATE this machine, and I dont think that its fair that I get stuck with it because of the way it was made. I have to constantly redo the load because it doesnt drain and rinse. When the load is done the clothes are still soaked. I dont understand how technology can go backwards when it comes to washing clothes. SOOO DISAPPOINTED!!!

My Maytag microwave MMV4205BAB gave out this a.m...again. I bought it in 2008. The repairman has become a close personal friend because he visits so often. In Jan. 2012, I bought an extended warranty, which expired in Jan 2013. This is the best example of planned obsolescence Ive ever seen. We wish we had kept our GE with the broken handle, which we had for 20 years with no other problems than that. If you are wise, do not buy Maytag.

This Maytag Bravos HE machine has the poorest design! It doesnt use enough water on the normal cycle so I always have to use the bulky load just to get the clothes wet. The old washers used to spin the water out thus keeping the load even. This machine drains the water first and then tries to spin an uneven load! When this happens the machine bangs loudly from side to side, stops, refills with more water and starts the whole process again until it fixes its problem or until you go shake out the entire load and reposition everything. Then it uses more water to start the process all over again. It takes twice as long to do a load of laundry.Every time I use it I say I hate this machine! This machine should have never been released without extensive testing. Maytag could have figured out all of their own problems and fixed them so we wouldnt be writing all of these bad reviews. A recall should have been done years ago and the problems all fixed. I will never buy Maytag again!

The washing machine is rusting and Maytag refuses to take care of their inferior product and obvious inferior materials used, and also inferior workmanship.

We bought the fridge (MFF2258VEW2) about 5 years ago. We have had nothing but problems. First it was the water leaking all over the floor. The repair man said the drain tube in the back was too small. That was replaced. Then the door gaskets were replaced. The doors still do not stay closed. Again water leaking all over the floor. The bottom of freezer had ice all over it. I had to take the back of the fridge and freezer. For 2 days I had a fan blowing on to defrost it. The door shelves are cracked and falling off. I had to pay for the hooks that hold up the bottom shelf 5 times and again they are broken. The long narrow slide out shelf is broken. Food in the back of the fridge are freezing. I have contacted Maytag a lot and they will not fix the problems. At the same time I bought the fridge I bought a Maytag top load HE washer and a drier. I had to throw out the washing machine last year. It would have cost me too much money to fix it. I will never EVER buy Maytag again.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

The Bravo HE Washer was a cheap piece of garbage and I am very surprised Maytag put its name on it. It broke down exactly one year after the warranty went. It did not ever clean clothes properly and all stains remained even when you spot clean first and double rinse. Maytag basically ripped us all off and somebody should start a class action lawsuit for this thing they call a washing machine! What a joke! I wont repair it. It will just fall apart again. Im not stupid. I know this is how they pay their employees doing house calls! So now, I have to go to garage sales and look for one made in the 1970s because that is when machines were made in the USA and things were built to last, not this crud. Maytag should be ashamed. It is time for them to close its doors. Sorry but its true. They are just crooks now selling crud that falls apart! They owe me a full refund.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

Purchased dishwasher from Highway Appliance in Dunlevy, PA on August 21, 2013. In August, 2015 control panel apparently went bad. When pushing normal, other buttons light up, but not the one you select. Tried throwing the breaker to reset, to no avail. Based on reviews, seems like many others have the same problem. Step up and do the right thing Maytag - recall & replace these machines!!!

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

This is the worst washing machine I have ever had in my life. Machine started bouncing during the wash cycle and also the spin stopped. Never in my life have I had a machine fail on me like this one. I spent a lot of money on this. This machine should be recalled. I read up on all the complaints. Its a model #Tw6600TQ0.

Because of the power of advertising, we replaced every appliance in our home in 2005 with Maytags. Since then, weve had minor problems with the stove and dryer, many problems with the dishwasher and washing machine, and complete failure of two Maytag microwaves, the last one was only two years old. The washing machine failures resulted in major flood damage two separate times due to two separate failures. Our refrigerator, model MBB2256GEW, has yet to let us down, however, since new it makes loud snapping noises that wake us up at night. It sounds like someone banging two large sticks together. Fortunately, I can repair most of these issues when they arise, but Id much rather get some rest like the Maytag repair man...

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

I have had KitchenAid and Whirlpool my whole life - lots of them - NEVER EVER have I had so much trouble with a washer. This front loader is the worst possible machine. My former Whirlpool was a front loader too - Never a problem. I purchased this Maytag set simply to have a matched set because our Whirlpool dryer died. This washer has to be babysat. The washer holds water and it gets musty - never ever before have I had this problem. Maytag says it is designed this way and I have to continue to buy AFFRESH (which is also very expensive). I have to use this two to three times a week and the pkg says once every 6 months - DONT DONT BUY MAYTAG. LOUSY.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I purchased this machine 6 months ago - have called 2 repair people. Thank God I purchased at Sears with extended warranty, was just replaced. I would tell you if you are looking for a machine run away from this one. It tears clothes, have to wash everything on bulk wash or I would not get enough water to say how bad this washer is. If someone called me and said I won this washer, I would say no thank you. And if I had to say Maytag repair called them, said she not getting enough water. Now this is what they told him: thats how we designed it. Forget about big drum, you cant put blankets or any larger items, goes off balance. And I have to say, if I had the money, I would put to the road and go back to wringer type. So again, do not make my mistake. Do not buy this washer and let me say the second day I made a complaint, was told it take time to get adjusted...NOT. I give this washer a 0.

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

The middle piece of glass on my four-year-old gas oven shattered. It was not being used, but when I called Maytag, they told me that that was not covered because I did not have an extended warranty, and that I can purchase a new oven door and would have to pay the service person. I hope they go out of business. Maytag stinks, and everyone should know this.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

Refrigerator 1F122269VEM7 not making ice, shelves broke, freezer drawers stuck, and motor running like an automobile. Refrigerator only 2 years old. Paid 4000 dollars and this is not acceptable. Reviews online very disappointing. Other reviews on this product not good. People having all kinds of products with not resolve.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

We have a model MF12269VEMS. Approx 3 years old. Ice maker and water dispenser work great. Fridge works well. We have experienced over the last 6 months a buildup of ice that forms inside the freezer under the drawers. If we dont catch it every 4-5 days we cannot open the drawers as the ice catches the bottom plastic drawers. I called Maytag directly and the pleasant young lady told me after checking that it did not seem to be an issue...clearly after looking into the internet I am not alone! Maybe someone can email me a fix?

Before today I was happy with my washer. Well yesterday I heard this loud noise. It turns out to be the gear case on my washer. To my surprise the repairman told me that it would cost between $450 and $500 to replace. I called Maytag to check on the 10 years warranty and was told that it would cover the basket and the motor but not the gear case. That is very stupid because without the gear case the washer will not work. This gear case help the sensor work, the basket work. DO NOT BUY ANY A MAYTAG PRODUCT. They do not stand by their product. I have had my washer for 2 years and 10 months. Before this the last washer I purchase was a Lady Kenmore through Sears. I had that washer and dryer for 25 years.

Ive had my Maytag refrigerator for 19 years and it still performs well. I keep it clean both inside and underneath. The lighting is one aspect I really appreciate as there are two bulbs in the interior so theres never a problem seeing all the contents. Also appreciated are the movable shelves on the door and the ability to raise or lower the main shelves in the body of the fridge.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

We purchased a Maytag dishwasher mdb7749sbm1 in 2014 and have had nothing but problems with it since it was delivered. Within a year of owning it, the top jet fell off. We had it replaced and the repairman warned us that it would probably come off again due to a faulty latching system. In the last six months one of the brackets that holds the upper shelf has broken off and the dishwasher leaks every time we use it.My last cycle leaked so bad that essentially it completely soaked the extra large bath towel we place in front of it and travelled halfway through my kitchen. Not to mention that it never washed dishes well, regardless of what cycle we use, which/how little or much detergent/rinse agent and it does not filter at all, as theres debris all over my dishes and glasses. I am now looking to replace it before like other reviewers a control panel fire occurs. Strongly recommend staying away from this brand.

I have a Maytag dishwasher and the rollers for the racks are failing due to heat: plastic wheels breaking up. $35 each to buy and replace. There are eight total. So $280 because of poor testing and quality of materials. Manufacturers should test to ensure the parts last a reasonable period of time and are designed for the environment in which they are being used.

Model # MF12269VEQ1 French doors with bottom freezer - This refrigerator was purchased March 2011 and it is forming a sheet of ice on the bottom of the freezer. We tried unplugging it overnight to see if it would correct itself and it hadnt. I googled this complaint and called the manufacturer to see if there was a recall. It seems a lot of people are having this problem. Several comments are to pour hot water in the drain plug or use a blow dryer to to the plug; however, you have to disassemble the whole bottom freezer, then unscrew the back to get to the drain plug. I feel this is a defect in this refrigerator.This unit was approx. $1600.00 and should not be having this type of problem. Who knows if I could actually get to it to try these things, that it could keep recurring. Im very upset as my husband and I are seniors on a fixed budget. We bought the name Maytag because we thought they built good products.

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

The water drainage tube on the Maytag Refrigerators is DEFECTIVE and needs to be replaced during manufacturing of the appliances!!!!!!! The existing drainage tube kit in the appliance has a very tiny opening for the water to drain and what was not factored in during this manufacturing of the refrigerators was bacteria and dirt build up from the water draining to CLOG this very TINY opening in the existing drainage tube system. This results in the water having no place to drain except causing an ice build up in the freezer and then water draining onto the floor when it has no where to drain in the appliance. I am told by my reputable Maytag repairman, who also needed the same repair, that replacing the water tube drain #W10619951 occurs with customers 4-8 times PER WEEK in his practice. This is obviously an ONGOING defect that Whirlpool is IGNORING and needs to be addressed and corrected with some type of compensation for its customers. The service call and the replacement of the drain tube kit #W10619951 cost me $122.31. My Maytag refrigerator with a bottom freezer is less than 3 years old.Amazing also if you google MAYTAG refrigerator leaking water there is a MULTITUDE of youtube videos and websites instructing the consumer on HOW to replace this part in the refrigerator. Obviously there is a strong need for this instructional information to the consumer for this repair since it is an ONGOING PROBLEM that has not been addressed legally with manufacturer. Action needs to be taken. I am saving the original part that was removed from the appliance in case a class action remedy is necessary to correct this costly defect in the Maytag Refrigerators.

Bought top of the line Maytag Commercial Technology washer because it was supposed to be the most advanced on the market. My experience has taught me that advanced does not equate to efficient, effective, and expedient. The washer settings for an average load (sheets or towels or clothing) is about 111 minutes per load (nearly 2 hours!!). To adjust to what would be a quick wash is about 25-30 minutes BUT the washing part of that is only about 5-7 minutes. I feel like a Pioneer Woman because I must spend most of a day to run four (4) loads of laundry (sheets, towels, dark clothing, white clothing). This is extremely frustrating!! I am sorry I purchased this product.

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

2013 We purchased from Lowes Maytag washer and dryer front load stackable. We live in a house 1890. We have a closet that these units go into so we are restricted to what brand we can buy. WE read the reviews. People must lie or are paid to write good ones. Within a few weeks the washer was giving us trouble. The door latch was not closing properly and it would take up to 20-30 min. to get it to start. Called and they said the latch was stuck. Again started having problems on and off. Months went by and had another service call. Same issue. Fixed it again. 2014 again same problem. We have to order a new latch and some other part. They could not get the part. Called Maytag directly and they were back ordered. What does that tell you. This is a major problem so much so that no one anywhere had the parts. 6 wks to finally get it and got it fixed. But in the meantime, the dryer was not working correctly. The clothes were damp and lint was all over. It was like a steam bath. They came out and when they looked at the back of the dryer it was burnt. Now this is what upset me. He said it could have caught fire and burnt down our house. Nice. The dryer was shot. They said to fix it would cost more than it was worth. Our warranty gave us a new dryer. 3 wks later I have my washer and dryer back working. In the meantime we have spent more time at the laundromat than at home. Brand new washer and dryer and are going to the laundromat. We had the dryer 5 days before it stopped working. Brand new dryer. Called and got a service call. The spring on the start button was not correctly put in. Who inspects these products. This was not right from the factory. So they fix it. Said if it happened again they would need to replace the entire thing. I do not know what that means. That was Dec. End of Dec. the washing machine is not running through the cycle. It had weird display on the washer. Thought maybe it was overloaded. Had to cancel and drain and then hit drain and spin. This takes not only more time but more electricity. I put in 2 sheets and it did it again. Had a few loads that ran properly and again it started. Called for service. He comes out and the motor that runs the belt to spin and some circuit board is shot. They call 2 days later and say that no parts can be found anywhere. WTH! It is 18 mos old and already the parts are extinct. So the warranty company said it was not worth fixing. They are giving us a new washer.I remember the commercials about Maytag that the repairmen had nothing to do. Well I thought it was because they did not break down. No... they cannot find parts. This is unacceptable. We have to go through the inconvenience of them not working and schlepping to the laundromat baskets of clothes. In the winter this is not fun. We are retired. Have to walk down icy steps. I have a washer/dryer upstairs and I cannot use them. Dont work. Not just the aggravation of dealing with repairs but not getting parts available, then having to wait to get money back to order a new washer and dryer and then get the dryer and 5 days later it doesnt work. Now we have to wait 2 wks for a new washer. It better work. Have to buy the warranty over again on each product cause they fulfill it when they buy you a new product. So this costs us extra money. The money we pay at the laundromat. The cost of electricity every time we have to run the washer 3-4 times to get it to spin out the water so I can dry them.To say I am upset is an understatement. I was told by a rep at Lowes, well Maytag has about 3 lemons a yr and you just got all of them. That was their consolation to our problem. I think Maytag needs to inspect their product. Our house could have burnt down. It is not a matter of parts going bad but damn the stuff is not even 2 yrs old. And the dryer was 5 days old when it stopped working. WE had a Maytag dishwasher and it was installed brand new and did not work. It had a defect in it. I never got to wash one dish in it and it had to be repaired. So I am not happy with Maytag. You go on Facebook and tell your story and all the Maytag horror stories come out. You need to do something to save yourself. Your company name is going down the tubes. Thought you should know this.

I purchased a Top Loading Maytag January 2019 (High Efficiency Washer) and I have had problems with it every time I do laundry. It doesnt matter what cycle I have it on. It doesnt fill properly when I put it on deep full. It tangles my clothes so I have to untwist them when I take them out. It has torn some of my things due to twisting. Some areas of the clothes dont even get wet. Some areas also do not get rinsed properly and I have to repeat the cycle. I have had repair people come out and they cant find anything wrong. I am so unhappy with the washing machine and Maytag just ignores the issues I am having. Im going to have to give it away and get some other brand. I am just devastated that I spent all of this money and clothes are getting ruined.