In December of 2013, I purchased a Middle of the Line Maytag Dishwasher model #MDB8949SBW for $600 plus $200.00 for install and removal of 5 yr old Kenmore. At that time I thought I did my research and saw no major negative flaws on this type of machine or similar machines. This replaced a 5 yr old low line Kenmore that just upped and died. Installed just before the holidays, this Maytag machine seemed to have worked tirelessly until a few days ago August 18/2015. The computer controls went haywire. I was hitting normal start buttons and other buttons on the other side of the control panel were blinking and lighting up. Worse was trying to cancel and the control boards were not responding. Even hitting the start button, the machine would not turn on. Finally looking at the facia, I see the tabs of the flexible plastic frame that hold the control panel popping out from underneath the white facia plate. Snapping the frame back in and applying a lot of pressure got the machine to operate. With a family of four and minimal storage space, this machine is used approx once a day. It appears over the year and 1/2 by pulling on the plastic handle - which also happens to be the computer control board frame, the computer has separated from its mount and has allowed moisture to hit the control board/computer and wreak havoc on the electronics. Looking up this model online NOW, I see I am not the only one with Dishwasher computers failing within a year or two- just out of the one year warranty. A Call to Maytags customer service has the computer control board alone cost $160.00 plus the service tech and his labor fees reaching in excess of $450.00. The CS rep gave me a repair discount to $267.00 and a week wait for the Service Tech for this problem to be fixed. I bought this machine on two premises - one for its price, it was the only machine that offered 3 spin jets that really do a good job in cleaning dishes and 2, I owned a 1984 Maytag dishwasher in another home with computer controls in the handle and to this day, that machine is still running flawlessly! My only issue with the 84 Maytag machine was after 4 years the door gasket went - too much soap - replaced and no issues since! I expected similar performance with this one. I guess I have to spend north of 3 bills for similar performance and quality. What was I thinking?

This Bravo Top Loading Washer does not thoroughly clean my clothes. It doesn’t fill properly with water, and it leaves soap residue on my clothes, because it’s not using enough water. I’m using the 2 rinse cycle trying to prevent this, and it’s still not enough. It has actually ruined a few of my items. It is the WORST washing machine I’ve ever purchased. I’m disappointed in Maytag for producing such an awful machine and Sears for selling such a sub par product.

We purchased all Maytag home appliances when our home was remodeled about five years ago. After the first year, the microwave had to be replaced because it malfunctioned. The dishwasher stopped working in the third year, and now, my refrigerator (model# mf12568AEB) wont cool. The technician told me that all of the Freon had leaked out because of a design flaw. Moisture had gotten into the compressor, and with the cost of repair or replacing the compressor, I would probably be better off buying a new refrigerator, preferably not a Maytag.

I bought the largest Maytag top load washer. From day 1 clothes come out with laundry detergent left all over them. I have to take a washcloth and wash off every piece of clothing coming out of the washer. Had a technician come out. He said he gets this complaint every day. His suggestion, put less clothes in and use less detergent. This washer is programmed to use minimal water and it just doesn’t have enough water to clean all the detergent off. So, I bought the biggest washer to wash bigger loads and now you are telling me that just doesn’t work.Spoke with Maytag customer service. They said very rudely if there is no problem found when the technician came out, there is nothing they will do. She told me it was user error. My dryer also stopped working. Sometimes it would turn on, sometimes not. The technician said the lint screen error code came up. He would try to get Maytag to replace the whole board but usually they don’t do that unless the whole board has a problem. Called Maytag the next day. The technician documented he fixed a connection problem and closed the ticket. What???? So, now I guess I need to schedule another service visit. Very unhappy with 5 month old appliances. Paid $1700 for the pair, you expect quality products.

I bought a new Maytag refrigerator on July 2, 2011. The ice continues to drop after removing your glass. Now you must pick the ice from the floor. Maytag said it has a 10 second delay and will continue to drop ice. Im tired of picking up ice and wiping water from the floor. Who wants a product that leaves a mess?

I bought brand new Maytag appliances top of the line. I put the stove, dishwasher and refrigerator in and was waiting for the cabinets to be done before installing the microwave, It was a couple of years; I took the microwave out of the original box and had it installed and it made a terrible noise and then shut off. There is something loose or something. I called Maytag to activate my warranty but they said the time is up but I had never opened the box so I didnt know there was a time limit on sending it in. There was no customer service! The stove I bought for close to $2000 has had to have the control panel replaced 3 times so I have to pay every year for an extended warranty just to guarantee I have a stove. Last year I went through the holidays without one because it was out then too! I would never buy another Maytag again!

My husband bought a washing machine in August 2019 and now it broke down a month ago. There is a sticker on it that the warranty is 10 years, but this warranty is for the motor and not for everything else. I read on the Internet what kind of error the machine gives me, it turned out to be either the motherboard or the front panel. I did not order the parts myself, called the service, in 5 minutes I had to pay 130 $ to he told me the same thing that I read in Google.... And he said that the repair would cost another 500$ part - 250$ and service fees to replace the front panel or the motherboard. Its ridiculous prices, so I find parts lil cheaper and ordered the motherboard myself, my husband installed it (there is nothing hard to do it) and the machine still gave the same error, I ordered the front panel for 220$ and the machine still gives the same error. Now front panel didnt respond at all, and this brand new panel... So I bet after I will pay to service they will tells me there is something else broken... Maytag??? NEVER AGAIN!So I send all part to the store, save money this way and now I buying a new one, when a year and a half ago I spent 1000$ on Maytag and the service is trying to rob me at the cost of a new machine, and no one gives me a guarantee after the service, I will not have a new one. The way out is possible to read more reviews and take a protective plan for 5 or more years so this is not your problem.

After one year of service from our Maytag Jetclean Plus Dishwasher with Toughscrub the circuit board went out. I have been seeing and hearing other people complaining about this problem. We purchased this device based in large part on Maytags reputation for reliability. I am not happy with this machine. I will complain to the company and write another review based on the results. I suggest Maytag goes back to the old knobs until they can assemble and protect the circuit board, which I believe was damaged by heat and moisture.

On April 8, 2017 I was sitting in my Dining room with Dishwasher in the kitchen in cycle cleaning. All of a sudden I heard electrical sizzling and turned to see my Dishwasher was on fire. I got up and opened the door and my Husband shut off the circuit breaker for the Dishwasher. He raced to turn off water under sink and went to disconnect the dishwasher when all of a sudden hot water was shooting all over the place. I tried to catch in a bucket but it was so hot and shooting out hose fast. Kitchen and Dining room were then filled with water. He realized the turnoff under sink was installed at time of house built and cant be fixed without a lot of chopping up under cement.Well finally we cleaned up the mess with mop and towels and relieved neither one of us fell at our age. He unconnected the Dishwasher and secured outside. About 2010 there was a recall on this model Maytag. I reported it and a repair man came to change the cycle panel and said it would be fine, not. Yes almost 7 years later a fire occurred. Just glad we caught it in time without losing our lives or my house. Never, never again will I purchase a Maytag.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

Part on fridge is defective. They have sent the part but tell me they dont have anyone in the area to work on it. Nor will they pay for someone to come out. We must replace it ourselves. This product should be on recall. Maytag fridge. Freezer door on bottom filling up with water. We have 2 of them doing this. One about 15 years old. Other one is 3 yrs old. Maytag knows of the problem but wont fix it. Wont recall their default product.

Purchased a Maytag Bravos 300 quiet series and am totally dissatisfied. I have a bandsaw, router and several saws in my workshop and by far my Maytag washer can drown them all out with the noise it makes. On top of all this it does not complete its cycles before it shuts off and if you try to restart it you never know where in the cycle it is going to start at. This may occur six or seven times before you are able to complete one wash. It may take a day to wash one load of clothes. Maytag should refund the total purchase price of this piece of junk!

We purchased this washer from Sears. Its always been loud during spin, but the past couple months it has gotten VERY loud. It jumps around. Also, it tends to ball clothing and towels. It has been hard on my clothes and bedding. Many times I have to rewash towels and bedding, even jeans at times. I have been very unhappy with this purchase from day 1. It was not a cheap washer.

Friends, Romans, Countrymen, At first I was skeptical and I once thought that I was the only one whose wife complained about the terrible soap stains and un-rinsed clothes. And finally my rinse and spin cycle stopped spinning and rinsing! However, after reading several reviews and complaints about the famous Bravo X He washer by Maytag and taking into consideration that there are over 650 complaints, making mine # 651. I now find I have lost all skeptical-ability and feel that we all may be comrades in this venture of purchasing the new trademark of the trade-mark Maytag. As almost all of us say our previous experience with Maytag was great. My parents had a Maytag since I was knee-high to a grasshopper and we were a family of eight. First we had the one with the rubber rollers, that was a work of mechanical genius. I even remember getting my arm caught in the rollers. Then my dad bought the spin dry model and that lasted a good 20 years. When I say the Bravo X at Sears it looked like the state of the art washer. However, and unfortunately I will have to agree with all of you. It is a piece of scrap metal and Maytag will not recall or recognize their mistake and make good on a recall or something. The least they should do is give us an old machine that does wash and spin to replace the new one that is less than 2 years old and does not work. I sure hope this letter does not fall on blind eyes. I think we may even have a collective lawsuit.Sincerely Yours;Mr. Lost All Skeptability!

It doesnt clean as well as the cheap GE model we have at our beach cottage. Also it is very noisy. Disappointing. Will never buy a Maytag dishwasher again.

I have a 50/50 chance of completing a wash cycle. Most times, the washer stops working at 8 minutes remaining in ANY cycle. The washer will leave me with wet clothing and refuses to spin even when most wet, dripping articles are removed. I have tried to put all light-weight items together and that still is not a guarantee that I can get this done in one cycle. Most often, the error code comes up, I spin the drum around, move the clothing around and try again. This process is NOT energy efficient which is why I bought the ** thing in the first place. I am ready to put it on the curb for the trash man to pick up.We had a service person out and he said it is either the bearings or the motor (both a $400 job). I will NEVER buy another front-loading washing machine. At least with the old-fashioned top loaders you can get the load balanced and at least get clothing to go through the spin cycle. I am now hand-wringing clothing once again since the machine tells me when it will spin my clothing. That stupid chime is about to send me out of my mind!

I love the way it can really handle large loads. The dryer is the best though. It actually dries your load without you having to turn it on more. There are many different choices that handle drying. So, no more to the bone drying.

My Maytag washer is only three years old and the control panel completely went. Not only did it cost me the service call, they want $360 to replace the control panel. I called Maytag/Whirlpool to see if they would help with the cost of the part. I am 60 years old and the only one who uses the washing machine. It is not beat up. Maytag would not offer any solution at all and refused to even pay for any part of the control panel. They said it was really my tough luck for not having bought the extended warranty. When you spend so much for an appliance, you do not expect it to only last three years and you should not need an extended warranty. I am so disappointed and I will never buy a Maytag or anything from its parent company Whirlpool.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

The machine does not rinse soap off clothes even after using 2nd rinse cycle. You have to wash clothes again using no soap at all. Defective machine maytag does not help or Clare wanted to charge service fee for tech even though machine is under warranty. This washer should be recalled. Very bad product. Lots of complaints.

What a disappointment. I guess this is why we no longer see that commercial about the Maytag repairman being bored. Because now, he is out fixing these pieces of shirt. Im trying to fix my washer (Model: MAH8700AWW), what a sweet pain in the **. Dont do it. Throw it away if it starts making noise like an aircraft landing.

We purchased this machine (Bravos XL top load washer) in August and its been nothing short of a disaster. It doesnt clean anything. Within two washes my cloth diapers were unusable, loaded with ammonia and stains. Our camping clothes wreaked of smoke. I tried multiple cycles, more detergent, less detergent, larger loads, smaller loads. Doesnt matter. It doesnt clean. I called customer service within a week and waited 6 weeks for a service call. Into third trimester of pregnancy and recovering from an MVA, I was washing soiled clothing by hand in bathtub desperate for help. I only wish Id known about their 30 day money back guarantee. After many calls, no shows and cancelled appointments, the first tech comes. He tells me the machine is fine. They just dont clean well. Hes not surprised. I call the appliance shop, they said the same thing. That they wouldnt have sold me the machine if they knew I had dirty laundry to wash. (Who washes clean laundry?). They wont help us. We call Maytag back. They send another tech. He says the same thing. Tells us to keep complaining to Maytag. I call again and they tell me that if I want a service tech, I have to pay. Theyve deleted all my feedback from their social media site and refuse to provide any assistance. The machine is nice looking and makes big promises but thats where it ends. Save your money. Youll get better results with your grandmas washboard.

We bought a Bravos model in May 2010. Two years later, the machine started making noise during the final spin cycle. We finally called a repairman who came today and informed us it was a bearing in the outer drum. The cost for the part (the drum assembly) was $290, not to mention the cost for labor. Since we only got the original warranty, the service center at Maytag refused to help with the repair. We, as others who have had problems with Maytag, bought the washer because of Maytags reputation. This is why we have to buy extended service warranties. Companies make trash! What happened to the days when an appliance lasted longer than 10 years? Why cant we buy a good sturdy appliance without superficial bells and whistles? We have no idea if any other brand is better, but we will not buy another Maytag.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

I have owned a Maytag washer since 1989 (25 years) that has had absolutely NO PROBLEMS WHATSOEVER. It now has a slight leak, so I am considering replacing it. I contacted an appliance store and advised them of my problem. The salesman made a comment which indeed surprised me. He said that, although he would like to make a sale, I should do everything in my power to keep that old Maytag machine because they dont make them like that any more! From reading the reviews about the new Maytag now I understand why! I do not plan on buying another Maytag, which really saddens me, as they were once a high quality, dependable product.

Have a Maytag refrigerator, less than 2 years old. Water is leaking from top of the inside of the refrigerator, presumably related to water dispenser, unrelated to filter, and dispenser still functions. In shock, Ill have to pay an additional $347.00 to Maytag for an additional warranty if I want them to remedy this!!! Model # MFT2672AEM10. Buyer beware! Upset that such a new refrigerator would have problems - more upset that the company is making no efforts to make it right without charging more. The refrigerator was not cheap in first place. Also the time spent to have someone come out... Maytag advertises repairman boredom.... Never had another problem with other appliances unless they were much older!!!

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

Purchased Maytag dishwasher model # MDBH979SAM1 on February 8, 2014. 6 months in paint came off door. Added 5 year extended warranty on 4/21/2015. Dishwasher started not working properly on 9/24/2015. Hit one button but a different would light up until finally on 10/2/2015 it quit working. Called for service On 10/2/2015 10:30 pm no answer. Tried again on 10/3/15 same answer. Tried again on 10-5-15 finally answered and they called repairman. No answer but they gave me his number so I could call him if he didnt call. Finally called him and He told me he was busy and could not come repair my dishwasher. I called MaytagNed they said he would come. When I called he said he was not coming. He had truck trouble. 10-12-15 Called Maytag back and they said they would find another repairman. They would call me back. Into 2 weeks waiting on appointment. I will never buy Maytag again. It didnt clean dishes good when it did work!

I purchased a Maytag Dishwasher April 6th, 2011. Its only 3 years old and now the control panel isnt working properly. Specifically, the start button. Contacted Maytag Customer Care service and they could not help me other than charging $80.00 for the Maytag Man.. which by the way, we arent suppose to see because of their superb quality in appliances. So I have a repairman scheduled for next week. I am an highly dissatisfied customer because the dishwasher is used once a week for the 3 years Ive owned it. Just a poor quality product which I will never purchase again. Model #MDB7609AWB3 Serial # F10202246.

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

Having had a household for over 40 years we have had a few washers come and go. I hate to say it but this line of washers should go. Worst pile of junk parts I have seen. Bought it from Costco a few years ago based on past histories of Maytags. Was I ever so wrong. It has never worked well. I chalked it up to being Water Efficient but after reading over 8 pages of scornful reviews, I was mistaken. Water level is always too low to do anything so clothes are needing rewashed. Have reverted to using the Bulky setting to do general washing as that fills the tub about 1/4 of the way. Then the spin cycles stops due to unbalanced load and loud banging of the wash drum, EVERY LOAD!!! And now for the past month Code DL pops up saying it is taking too long to drain. I have checked all hoses for blockages, none seen. And with the glass top, you can SEE the washer NOT WORKING right. We have a door on the laundry room and even with it closed the volume is over 70 dB and can overpower most conversations in our family room 20 feet away. I have been told that Costco may take it back but why punish Costco members for a design failure of Maytag??? Has anyone thought about a Class Action Lawsuit? The Bravos Quiet Series 400 dryer match to this washer has so far been flawless. I may have to dig the 20 year old Whirlpool washer out of the storage shed to replace this Maytag. Sad. I want to state my true feelings but I will not use profanity here.

The only reason I am giving 2 stars is because I didnt actually spend my hard earned money buying these machines, they came with our house purchase. At first I was excited to have a good quality washer/dryer... Now I understand why the previous owners left them behind. My complaints are like most of the others on here - takes way too long to do a load because of the stupid water sensor, it doesnt wash loads evenly so everything on top hardly gets wet and washed properly, lint all over our clothes, powder residue left behind even though I set it to 2 rinses, a lot of settings but missing useful ones like quick wash... just all around disappointing. At least one good thing has come out of this and we will not be buying Maytag for our new laundry room. Saying that I have also read so many bad/worrying reviews about Samsung and LG - cant any company make good, reliable, lasting products and stand behind a warranty anymore?!

Do not buy a Maytag dishwasher with model # MDBH969AWB1. I bought this dishwasher last Dec. 2010. I could not use it for 2 weeks, because the door would not shut. The repair man came & fixed the door. Then when I actually got to use it and after it finished running the cycle, the tub was dripping with water all over--top, sides, door, bottom. I had to dry the dishes on the top rack, and I had to leave the door open for days in order for the inside to eventually get dry. The first thing I noticed about this dishwasher when it was installed was that it was smaller than my other dishwasher. I hate the design because of the way they have made the racks plus because it is smaller--it holds less dishes than my old one did. I could actually get almost twice as many dishes in my old one than I can with this one. Do they not think of asking the consumer about what they want in a dishwasher instead of going ahead and making something that is not functional?I am so frustrated with this thing; it has brought me to tears. I just today went to Sears and looked at their Kenmore dishwasher. It is designed more like my old one than any of the other makes out today. I wish I had checked this out, before I bought this Maytag. Weve always heard how Maytag is at the top of the line with no problems, right? Dont believe it. I will never buy another one. Whoever is designing these dishwashers need to go back to 1990 and take a look at how it was designed and then go back to making them like that. I loved my older dishwasher, and I wish I had never let them take it away. I wish I had taken the money I spent on this ridiculous Maytag and had my old one fixed no matter what the cost. I made a terrible mistake.If you have an older dishwasher and it has given you good service for years, I suggest you have it fixed and keep it, because you will not like the performance of what they are selling today. It does not matter what brand you buy, they are all designed the same. Just take a look and compare them. But if you buy, please check out the Kenmore. I dont know if the performance is better, but the racks are better designed. My old dishwasher was a Hotpoint. It was the cheapest one on the market, and it gave me the most wonderful service ever. The dishes were always very clean, the heating element was fantastic, and it always dried the dishes completely. I cant believe they would make a product like they do today and sell them for what they do. The heating element in them today is not as good or strong as what they used to make. That is why the dishes wont dry properly. You get way less than what you pay for. Thinking a new dishwasher is the way to go, think again. Please, if at all possible, keep your old one and have it fixed over & over again. I hate this dishwasher. What a joke on the unsuspecting buyer.

My husband bought me a Maytag washer as a surprise gift. I was so excited to get a Maytag. I will never purchase a Maytag again. I am so tired of washing, rewashing and rerinsing my clothes and still not getting the soap out. I have used every different kind of detergent and used with and without fabric softener. I have also tried cold, warm and hot water. I would rather use more water and get the soap out instead of using more electricity to keep rewashing my clothes and then in the end having to take a wet cloth to get the soap out. Never had to do this with any other washer I owned. Very disappointed as I always thought Maytag was the best.

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

As with everyone else here I have had my second control panel go here. In the five years I have owned it the first was covered by an extended warranty that I had purchased when I bought it, the tough part is I was forced to buy another Maytag at a higher price because of a recall for dishwashers catching on fire. I found out about this by accident.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

My Husband bought a Maytag Bravos Washer 2 years ago this next month. The washer is extremely hard on clothes. We have to wash all clothes on hand wash to keep them from tearing up our clothes, and we are having to replace the door lock for the third time. Of course the last 2 times were not under warranty. So once again, I cant do laundry when I need to. Thanks.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

I’ve had my electric glass top range for four years. Normal use. I set the temperature to 425 degrees to bake a potato. At the 225 degree mark, the oven bursts into flames. The fire burned itself out in about a minute. I turned the oven off and immediately went to google to see happened. I’m pissed! This stove is only four years old!

Bought a Maytag front load washer. When it is operating it is very loud. Some parts of the washer are made of cheap plastic. The Optimum detergent dispenser also of cheap plastic failed after 1 month. Disappointed in finding out only the outside metal box was made in America. All inside components are made in China which raised the cost $300 due to recent tariffs.

Maytag Bravos XL - I am having the same problem as everyone else with this washer. My clothes do not get clean and they smell. Maytag advertises tumbling, rubbing action to get clothes clean but my washer does neither. The clothes lay in the bottom of the tub and never move except when in the spin cycle. I am going to file a complaint with Maytag and if they do not refund my money am going to file a DTPA claim against them for false, misleading and deceptive advertisement. They will have to pay up to three (3) times the purchase price of the washer. Maybe everyone else should consider the same.

I have owned a Maytag gas dryer for 10 years now. I have had to replace the idler and belt 4 times now. This dryer appears to be built as cheaply as humanly possible just to get it past its almost non existent warranty. The replacement parts are even worse. The idler has a bronze bearing in it as a wear item. Really??? Why was this never even considered as a part that could be lubricated at least occasionally?Granted, lots of people do not have any mechanical ability at all and just pay through the nose for a repairman to come to their place for any repair then pay dearly for the service but, I DO have mechanical ability so I do all the work myself. That is why I know firsthand about the terrible manufacturing results and the very cheaply built replacement parts available at outrageous prices.

My husband and I bought a Maytag Bravos HE washing machine 3 years ago at Home Depot. It is by far the WORST appliance purchase we have ever made in 40 years! This machine started making horrible grinding noises about 6 months. It is not rinsing properly and its leaving detergent stains on our clothing. This washer needs to be recalled. I will NEVER buy another Maytag product, EVER!

I purchased a Maytag Bravos HE top loading washing machine two years ago. The clothes hardly get wet enough to get clean. It leaves a residue on dark clothes and the basket goes unbalanced at the drop of a hat. Whatever you save in water, you spend on electricity because a cycle takes twice as long as a conventional washer. It goes out of balance and bangs the machine enough to walk it across a room. I purchased this machine from an appliance store, not some discount house. I have had machines last 20 years and this one is shot in 2. I will never, ever purchase another Maytag, Whirlpool or KitchenAid product again ever.

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

We bought a refrigerator June 4th 2014. 6 month ago the freezer and refrigerator was getting warm. Had to call repair service, it was the blower! On Saturday 12/9/17 freezer wasnt freezing, then fridge was clicking on and off. Unplugged it, called repair service, it was the compressor. $800.00 to fix it, the same amount as when we purchased it. Repair service told us to call Maytag, he said, Maybe they will help you, would not help at all. Talked to Lori, all she said was warranty is up after a year, I then said, I think a refrigerator should last longer than 3 years! Will never buy anything Maytag again! Yes Maytag does SUCK!!!

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

I wrote the below to Maytag on their FaceBook page, of course havent heard anything back from them. Adding this on since I forgot about it, I have dogs and wash their blankets often, not that theyre dirty just for the dog smell. I have to wash them on the sanitize cycle which is an 1.5 hours long because if I use the normal cycle which is only 43 minutes they come out smelling exactly the same way they went in. I saw someone else post that their mothers front loader doesnt put in enough water so Im wondering if thats what happens to mine. So wish I would have checked the reviews before buying, thought I was getting a great washer buying Maytag.This is what I wrote on their FB page: I bought a Maytag front loading washer on 5/10/16 which was delivered and set up on 5/13/16. On Wednesday 10/19/16 it stopped working, so just over 5 months from the day it was installed. I called your company on 10/20/16 for repairs, they couldnt get here until today, 10/24, so 5 days with no washer. The customer service rep had all the details on what happened and Im sure passed them along to the repair company. He ran diagnostics, said it was the drain pump which was obvious even to me, but claimed to not have one with him even though they were in stock. Cant make it back until Wednesday, so two more days with no washer. He then proceeded to tell me that the dryer had to come off (stacked on top since the washer is a front loader) before he got back, that the warranty wouldnt cover two people coming out. So Im supposed to spend more money to hire someone to come out, take off the dryer and then pay them again to come back and put it back on. I called the customer service department again and was told they dont cover installation which stacking is. She said the warranty doesnt cover stacked units, as far as I can find that isnt stated in the warranty so please let me know where that is stated in writing. So I have a just over 5-month-old washer that needs repair already (bodes well for the future doesnt it??), will be without a washer for almost a week because the repairman didnt bring the most obvious part with him (maybe wanted to be paid for two calls?) and have to pay someone else for installation so it can be fixed. So wheres the Maytag man? I am not a happy customer and will be letting as many people know as possible. Ill be in the market for other new appliances soon, will sure as hell make sure theyre not made by Maytag, Whirlpool et all.

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

I purchased this washer because of Maytags reputation of the repairman who was supposed to be needed less. Ha! Was that a joke? Ive only had this washer 5 years, repaired once and now it sounds like its gonna blow up. Please dont buy one… Maytag has a one year warranty, but unfortunately I didnt take one out due to their reputation. Plus its hard on the working class to come up with the extra for the extended warranty! I dont normally write reviews but thought maybe I could save someone else a little cash!

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

Maytag dishwasher does not clean dishes. It has hot water and we have had a repairman look at it and he said water jets working. We have to wash all our dishes by hand before loading them into the dishwasher to sanitize.

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

Maytag dishwasher, MDB4651AWW was purchased on 15/02/2010. Touch panel was replaced under warranty on 16/08/2010. Touch panel became defective on 04/07/2012. It was $103 for the service call: panel was not replaced (too costly, > $200). My 2-year old dishwasher is now useless. The touch panel on this model has failed twice in two years and is obviously a design failure. I would ask for a free replacement panel.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

A dishwasher was on sale $500 and stopped working in under two years. It was a stainless steel Maytag. No one will help service it, and it seems unreal that a dishwasher should break down so very quickly. To not already work in under two years is astounding.

I bought a high capacity Maytag Bravos washing machine, thinking it would be better than the ones that shred your clothes around the center post. Wrong. You still have to wrap your clothes around the edges as if there were a post, and even then the machine will become unbalanced (after much thumping and crashing), causing it to stop, which forces you to redistribute the weight, sometimes several times in one load of wash! I called the company and got nowhere -- I wont say nowhere fast because it took forever to get nowhere. I do not recommend this machine.

Purchased a non agitator washer 1 year ago. Constant frustration with the sensing technology. Cannot select a water level or load size. The expectation is that the machine will do that automatically. The water dispenses through the soap container adding soap to dry clothes which then leave white marks on dark clothes. All of the selections for loads do not have a water level close to covering the clothes. The only way to achieve coverage is to reopen the lid multiple times to restart the sensing feature. Another option is to add wet clothes to increase the weight to “fool” the sensor. Some clothes have come out of the wash still dry in areas. Every load, no matter what size takes a full hour to complete! There is no quick load to be done! I have paused the cycle to leave the house and the water drains from the machine causing you to begin your 1 hour cycle again. Epic fail by the Engineers to provide a user friendly machine. This one, as time goes on, just becomes more frustrating and yes very noisy during the spin cycle.

Purchased Maytag Bravos Washer in 2013. Used a little over a year and had to put it in storage for 2 years. Biggest piece of junk Ive ever had. Ive had cheap washers that lasted more than 20 years! Repairman said all diagnostics read normal. I put a very small load in to show him the water was not even wetting the clothes and only swishing them around a little. The shirt on top never got wet and was still in its same position when it went into the final spin. He said this is normal. He recommended I dump the machine and find an old NON Maytag model with the tall agitator!!! Ive tried using all the settings combinations; and the water level never gets all the clothes wet and clothes do not get clean. Will NEVER buy a Maytag product again.

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

Top loader Maytag Bravos type 588-03 - This washer is extremely slow and does a very poor job of cleaning. I use the recommended detergent (I use Tide HE) and follow the directions being careful not to overload. I can tolerate the slow operation I guess, but the poor cleaning is a real problem. When I put a plastic shower curtain in it, no clean happens. I just throw them out and but new every time. I will definitely go back to a Kenmore with an agitator.

Maytag Bravo Washer and Dryer XL Series - This the worst washer and dryer I have ever owned by Maytag. I wish I could give them away. The washer does not clean my clothes and the dryer does not dry my clothes. They are absolutely terrible. Do not buy them, you will be sorry.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

I purchased a new Maytag washer and dryer March 2021, I have owned past Maytag washer and dryers, thinking they were the top of the line products, not this time, The washer, I put the clothes in barely covers the clothes, so I put it on deep water wash, when the clothes are all done, they look like they did when I first put them in the washer, dirty clothes, whites are dirty, towels look like they got dirt spots on them. The machine makes really weird noises, my little dog starts to shake, gets so scared, she runs under the bed and wont come out. The dryer, makes a very loud buzzer sound, she gets so nervous, when she hears it, she jumps up into my husbands arms shaking. I will never buy a Maytag washer and dryer ever again, they are totally different then the old ones, they had a good product and ruined it.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

I unfortunately just had the same issue concerning my unit. The unit went berserk, stopped cooling and ruined all my food. I managed to get it outside after leaking spoiled food all over my floor. I washed it out and contacted Maytag after reading the hundreds of complaints. They sent someone out to fix the panel but he couldnt get it to cool. He said many times when a unit goes down that the acidity from produce along with moisture can eat through the aluminum components causing a freon leak. Obviously, this happened to me. I contacted Maytag and they said they would fix that too but once I called back, they said that it was a separate issue. Then I spoke with another person who said they would send a tech to inspect. I took off work and finally got a courtesy call from tech saying he was told not to come. I was amazed I missed work waiting and got no call from Maytag saying they changed their mind. I called back in and was told flat out I would not be covered, even though the fridge was fine before this happened. I suggest everyone read over the Consumer Protection Act which covers defective equipment causing issues by both injury and property damage. A class action lawsuit needs to be organized concerning this also. In the meantime, I implore each of you to file a complaint with the Better Business Bureau in your state along with Michigan where Maytag is headquartered. This will guarantee a response from corporate. Also, make copies of this forum and send it to your State Attorney General explaining how you have been sold a defective item. They say ABC news once did a segment on this fridge issue also, so I suggest contacting them asking for a follow-up story. For those that use social media, go onto their Facebook and Twitter page to post a link to this site and the way you have been treated after spending over $2,000 and a fridge that has lasted 7 years or less. Its time for small voices to unite to form one that is much larger.

I recently purchased a Maytag centennial washer and dryer from my local Home Depot. I set up a delivery date of 2/9/12. I was contacted on 2/6/12 by a Maytag staff telling me that my washer and dryer were on back-order until 2/29/12. This is unacceptable to me. Why does your company not tell its retailers that some items may be back ordered? I would have accepted this if told when I scheduled my original delivery, but being told days later and after taking the day off from work, is poor customer service to me. I am giving very serious consideration to voiding this order and finding a new company to deal with. I do not have the confidence that future issues will be shared or dealt with in a timely manner.

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

MFI2670XEMS - I bought a Maytag Fridge MFI2670XEMS in 2012. I dont remember how long it took to start leaking but it wasnt long. Same thing as what most people are complaining about - I also have hardwood floors that are ruined. I just had a kitchen remodel and now I wish the floors werent new. Warped badly under the fridge. It is a constant pain. I have to break up the ice with a blunt object to get it out. I was so excited to get a new fridge. Of course it was on sale, now I know why. I wish I had just kept the old one, at least my floors would look great. Lame.

I purchased a Maytag dishwasher model number MDB7749SBM in May of 2013. In August the dishwasher control panel stuck on Rinse only cycle. It has been stuck on this cycle for a month. I contacted Maytag and they walked me through a reset. It has not worked. It looks to me as if the control panel has failed. This seems to be a common problem with the Maytag dishwashers. As soon as the warranty expires, so does the dishwasher. I purchased this dishwasher from Home Depot for over $600 thinking I was buying a quality product. My previous dishwasher was also a Maytag, even a lower end one that lasted almost 14 years! This one has not even lasted 14 months!!I was told by Maytag that I could purchase an extended warranty for $267.45 that would last a year. I believe, 4402 based on other reviews that I will be dumping more money into this one even after that. Very disappointed!! I will never buy another Maytag product again! I should have bought the Bosch. It was roughly the same price and high quality. I bought Maytag based on my previous experience. No More!!

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

My wife and I bought the Maytag commercial Bravo set about 5 years ago and both the clothes washing and dryer machines are still working as great as the day we bought them. Im a bit biased though as I bought Maytag commercial products in the past and will continue to do so because its they are a dependable company made a reliable machines.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

We purchased a Maytag Gemini gas range last year in April and the extended warranty. The ovens have not worked correctly since we bought it. I never do this type of thing, however, I am just disgusted! I am going to exercise my right as a consumer to express my customer dissatisfaction and share using the social network. I dislike Maytag and even dislike A&E factory service more! I have never experienced such bad service on a new appliance. What is even more concerning and the reason I am posting this warning is there appears to be no recourse! I googled search both companies and the first things that came up were complaint pages. How sad! Buyer beware! If you buy a new appliance, research the warranty provider. It appears that Maytag has laid off the Maytag repairman and went to a lost cost unskilled service provider! A&E repairman has no idea how to fix the oven. He replaced the part. 4 weeks later, came out and walked in the house and did not even look at anything and ordered the same part again. He told us he would be back the following Friday. He did not schedule an appointment. I called on Thursday before he was due to show on Friday and A&E told me I had no appointment scheduled. They told me to inspect the parts that were shipped. I told them I would not even know what I was looking at! They told me the repairman would be back out between 1-5PM on Friday. No one showed. At 2PM, I called and A&E said the repairman must be on his way because he did not call and say he wasnt coming. But again, he did not show! I made no less than 6 calls to A&E and Maytag after that! A&E would not escalate the situation to a supervisor and on call number 6, when I finally got to an advocate, they told me to call Maytag! I have taken 4 days off as vacation to be home for the repairs and this last day was the final straw. When I researched escalating paths for both companies on Google, the first thing that came up was whole pages dedicated to complaints for both companies!

Love my Maytag washer! It is great to have a clear lid so I can see the clothes being washed. Not only the features, it really cleans my clothes. I was surprised at the stains that are removed just from washing them!

My Maytag dishwasher MDB7749SAM is not quite 5 years old. At the end of December 2016 a bubble appeared on my vinyl floor. The plumber could not find any broken pipes or reason for any moisture to have gotten under the flooring. A flooring company did not know what was causing the bubble, moisture or the vinyl glue had failed. The floor got worse and worse, more bubbles.Called the flooring company again. Raised the register cover and could see all the moisture under the vinyl and underlayment. Plumber discovered the dishwasher fill valve had failed but because there was so much insulation on the kick plate, at the bottom of the dishwasher, it forced the water, which was in a pan under the dishwasher, to push the water to the back by the wall and under the flooring. Plumber said, the insulation acted like a dam to keep the water from showing in the front of the dishwasher. The first and subsequent bubbles, in vinyl were 3 feet away from the dishwasher. No way to tell the dishwasher had the problem. Has anyone experienced this problem? If not, take care to remove the kickplate and check your dishwasher for water problems.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

I bought a new Maytag dryer model # MEDC555DW2 18 months ago. Prior I had owned a Whirlpool for 22 years and the only expense on maintenance was that I replaced 3 belts. This new Maytag started making a terrible noise so I called the store where I bought and they sent out a tech. $76.77 they charged me to...remove a penny from where it got lodged in the edge of the drum somehow. Maytag refuses to do anything about it and I feel like Ive gotten the shaft because I bought an inferior product. In 22 years Id guess I dried on accident over 100 dollars in change since I have kids. Should have bought a Whirlpool again and so should you. Ill never buy another Maytag product. Ever.

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

I purchased a Bravo washer and dryer set about a 2 1/2 years ago and had problems from the start. The dryer control panel went out the first day. No problem, they replace the panel. The washer is a different story. The agitator went out next and the wait time to repair it - 3 WEEKS. The agitator went out again for the second time and the tech stated that it had to be replace. Wait for it. Waiting time - 1 month including parts. To make this story short the agitator will go out every 4 months and the tech stated once its been replace it will work like a new washer. Wait for it. The agitator has been going out ever since and the wait time average 3 WEEKS. Wait for it. This Maytag is trash.