I bought a complete kitchen: stove, fridge, dishwasher microwave. Suppose to be stainless steel. All have rusted out within 6 months. Maytag does not stand behind their products. They sent me cleaners and all my appliances rusted more using their cleaners.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

We purchased a front-load Maytag washing machine (Model MHW3505FW1) two years ago this month. When the machine is empty, we always leave to door open. We dont allow clothes to stay in it for long, never for more than a day (the load is usually changed as soon as the cycle is over). Right now, the rubber seal on the front has tons of black mold on it, and when I lift the seal to look underneath, its way worse. There have been many problems like this reported on front-loaders. Wish Id known! Maytag will not send a replacement seal.

I made the mistake of buying the stainless steel bottom freezer (model# MBL2258XES1) approximately 1 year before the freezer started to make a periodic clunking sound. The repairman responded because my year warranty was still active and found no cause for the noise. Fast forward a couple of months later and it started pouring water out onto my hardwood floors!!! Unfortunately it happened while we were away and my floors were destroyed. Maytag wants nothing to do with me. Im so disgusted. I now have to have a towel permanently on my kitchen floor. Nice. I made the unfortunate mistake of buying an Amana dishwasher recently not knowing that they were also owned by Maytag. The dishwasher is a water waster :( This is very disappointing - you try and buy American and you get screwed. If any lawsuits start up, sign me up!!!

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

We purchased a Maytag Bravo Washer and Dryer in late 2007. We had a one-year warranty on the set. At just over 2 years, we started having problems with the washer. It started making a loud noise when spinning and started beeping all the time during the cycles. We contacted Maytag and they said the only thing they could do for us was to sell us an extended/repair warranty for $320.00. If the cost of fixing the machine was too much, they had the option to replace it with another machine equal to the value of the machine in todays market, or cash, or a gift card equal to that.We were angry about the cost of the warranty and we were unemployed at the time and couldnt afford that so we just had to let it go. The machine progressively got worse where only two of the cycles would work, but not without beeping several times where you had to fix the load, and the sound got so loud it sounded like you had a jet plane just overhead. Just the other day it completely quit working. We have been in contact with Maytag several times but their only answer is their repair warranty. Weve talked to numerous appliance repairman, who all knew exactly what was wrong because they have seen it so many times, and they told us that we have several things going wrong with the machine we would probably need a new drum, a new drain pump and a new control board.We were told that it would cost more to just buy the parts than it would be to buy a new machine. In the course of our phone calls to Maytag, they have continually told us that they are sorry but there is nothing they can do, in fact they only have record of two of our calls (how convenient!). Since experiencing the issues with the machine, we have researched it online and found that scores of consumers are dealing with the exact same problems we are having which shows that there are defects in the manufacturing of these machines. Maytag should be forced to fix these problems. They are well aware of them and they should have to back up their products.There should be a class action lawsuit out against them. We were told by an appliance repairman that Whirlpool (who bought out Maytag) has a washer called Cabrio that is the exact same model as the Bravo and that they do have a class action lawsuit out against this model. Consumers that purchased the Bravo should be included in that lawsuit. I am stuck with a broken down washer, mildewing clothes and dont know where to turn outside of paying out the money for the extended warranty with no guarantee of what we would get out of it, purchasing a used set with no guarantee, or putting out the expense for a new set.This set was an expense set and we went with Maytag because they used to have a good reputation, but we feel like we have been totally cheated. If the appliance companies were forced to offer a longer warranty on their products, they would have to manufacture them at a higher standard. For the cost of these new machines this is exactly what we as consumers should expect. Please help us to know which direction to go. Even with purchasing a new machine we are apprehensive!

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

Horrific, useless, inconsiderate, rude, discourteous, arrogant and banal! I bought a brand new washer and dryer. The dryer is steam type and defective and they will not exchange, despite never being used. Nowhere am I committed to an agreement saying that the machine will not be replaced if it is defective. I am getting the run-around from the store, the manufacturer and the service technicians that didnt even arrive with tools when they came to evaluate the problem. If I had my way, I would return the washer and dryer and change manufacturers. But it is a stacking unit and I used the washer which commits me to it! Maytag, Whirlpool, JennAir and KitchenAid are all the same company. I am running out of options except going to the European manufacturers! Miele will at least install the appliances. They will be my next machines and I will not have to pay a plumber twice to install them the next time!

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

Buyer beware. This machine has received several complaints. Not long after purchase, the washer started to stop during the fill cycle and give an error code no. This is supposed to be sure to overloading the machine. The other reason they give is something stuck item the baskets. Again not the case. Supposedly it must be a motor issue. Maytag was my trusted band. Our last Maytag lasted us almost twenty five years.I was excited to get this machine but disappointed with the lack of clean clothes, error codes, and noisy operation. My first clue should have been the one year only warranty. Thats how much they believe in their products. Ill never trust Maytag again. So sad that whirlpool should sabotage the Maytag brand and turn an otherwise great washer manufacturer into a piece of junk manufacturer. Dont buy whirlpool either as thats how much they care for customers.

Gemini Twin natural gas range - I bought this range approximately 18 months ago. I thought it had all the features I needed and it looked good -- looking good is just about all it does! If you are a real cook I would suggest you avoid this range. The burner controls are preset and it is impossible to turn the flame very low if a simmering heat is required. If you are making meringues, again, the oven heat cannot be turned to a cool enough temperature. Ovens bake/broil unevenly. It takes forever to bring a pot of water to a boil, not because the flame is not hot enough, but because the pots sit far too high above the flame. Bad, bad design. Probably designed by someone who eats take-out!!

Have a Maytag refrigerator, less than 2 years old. Water is leaking from top of the inside of the refrigerator, presumably related to water dispenser, unrelated to filter, and dispenser still functions. In shock, Ill have to pay an additional $347.00 to Maytag for an additional warranty if I want them to remedy this!!! Model # MFT2672AEM10. Buyer beware! Upset that such a new refrigerator would have problems - more upset that the company is making no efforts to make it right without charging more. The refrigerator was not cheap in first place. Also the time spent to have someone come out... Maytag advertises repairman boredom.... Never had another problem with other appliances unless they were much older!!!

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

We bought a Maytag Bravos three and a half years ago. We always tried to follow instructions for the machine. Only used he detergent, used the affresh, tried not to overload the machine etc. Had to call a repairman. Our washing machine started leaking water at the bottom. Hoping that it is only a three machine it would be fixable. Bad news the repairs would be over $600.00. It needs a new tub seal and bearings. For a THREE YEAR OLD washing machine! The repairman and I had quite a talk about appliances. He said they just dont make them to last anymore and the companies such as Whirlpool, Maytag, etc. do on purpose and they get away with it. Stay away from Maytag Bravos. It is a worthless piece of crap. It will not last long. Now we have a three year old washing machine that does NOT work right. Something has to be done in this country to come down hard on the companies that make appliances. I would NOT recommend this piece of crap of a washing machine.

I bought this washer three years ago. It is the worst washer I have ever owned. Washing a load of clothes, it goes off balance constantly, large load, small load...it doesnt matter. The smell because of low water usage is awful, and the clothes dont come out clean. I have to buy a new one and that really stinks. Maytag youre off my list for purchases. These days its quality that will keep you in business. We are too smart for this garbage.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

I have a two year old version of this dishwasher (MDB894995BB3) and now the start and cancel light on the control panel stopped working. I now see that this is a common theme with this model and I feel it is their obligation to repair these units with permanent fix and not the same thing that will fail again. I have 3 different Maytag appliances all bought 2 years ago from Home Depot and they are all broken. I will never buy a Maytag product again. I might replace this dishwasher as I know it will fail again. 2 years on a dishwasher is a complete failure. Unreliable Junk. Do not buy Maytag.

I bought Tapan gas stove last year, but all your ranges have a problem. Whenever we clean the range, it never goes straight stay up ,even when I bought from Lowes Store and I told them they said that defect from manufacturer. You have to correct your manufacturers defect, I want an answer as soon as possible. Thank you.

I am extremely unhappy. This is a terrible washer (Maytag washer MVWC565FW). I am so sorry I didnt buy a GE. Terrible loud noises, shakes and vibrates like a plane taking off. Funny smells as if something is burning. Repairman came 1 week after purchased and stated nothing was wrong. A huge waste of money, I HATE, HATE this horrible machine!!! Totally unsatisfied, I would never purchase anything with the Maytag name again!! Wish I could get my money back!

Purchased a Maytag Bravos top load washer and dryer in May of 2011. We had our other Maytag washer and dryer for 14 years, and they were working fine when we sold them. We saved a year for a new one. We spent $1,700.00 for them both. We assumed they would last as long as our old ones. Been buying Maytag our whole lives. Besides the clothes not getting cleaned. Besides the washer smelling, even after we clean it regularly with the product proposed. Besides it not working on the normal function. Besides it shredding our clothes if you put it on the highest spin speed. It started to make a very loud noise. Like an airplane taking off. Called a friend of ours that use to have an appliance store in Fenton, Michigan for decades. He said it was the bearings and that You have to replace the whole tub. A $300-$400 fix. And that it would do the same thing again in a short period of time. He said that they are junk.We would be better off buying a new one. He said, The ONLY one you can buy now that will last like they use to is Speed Queen. I had never heard of them. They start at about $750. But they are worth it. He said that they dont make any washers to last more than 3-4 years anymore. We will NEVER buy Maytag again. And Sears wouldnt give us the time of day. Each time we called and asked to be switched over to the recall department, we just got a busy signal, then a fax machine noise. We have shopped at Sears for years. Boy, loyalty doesnt mean anything in this day and age. Im sure Speed Queen will be happy to help us out. DO NOT buy any Maytag products. There should be a class action suit against them for this. There are thousands of us that got ripped off. I cant tell you how upset my husband and I are about this. We are retired, and on a fixed income, and I am disabled. The stress this has caused cannot be put into words.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

After reading several of the reviews, it looks like Maytag doesnt get it - or maybe they do and its a plot to make more money. Our dishwasher model MDB8959FSZ4 was installed in Dec. 2016. Within the year, it started leaking. After many service calls it was determined that the arms holding the upper rack were not installed properly and were pushing against the door and water was coming out. After that was replaced, weve had 2 years of relative good use. Now, it wont empty and that started after smelling something burning. The burning smell has gone away but it wont complete a cycle. Service tells us its the drainage pump and that will cost nearly $500 to replace. We wont be spending another dime on this piece of crap. Well replace it with NOT A MAYTAG. Im wondering if it has to do with the control panel as many others have mentioned. We dont care to find out at this point. We are buying something else.

Our control panel just went out...purchased in November 2015. From reading reviews it appears our only option is to purchase a new control panel and hope for another two years. Ours (MDB7749SBM3 Dishwasher) was purchased from Sears and was not cheap. When is Maytag going to recall this panel? I read reviews that this problem goes back to 2011.

Have not had either inspected, but last night the dryer started to rumble and then caught on fire... Fireman suspected bearing bad and caused a spark igniting dryer; washer has started making a shrill loud noise on the spin cycle.

I purchased all Maytag products for my new home three years age. The dishwasher stopped working 13 months after we purchased it. Since the home was under renovations for the first month, we only actually used it for 12 months. When I called Maytag, they told me that it was either the control panel or mother board and that they could not do anything because the warranty was only for 1 year... and didnt offer me anything to make good on this...NOW three years later, my microwave is displaying error code SE.. control panel is bad. Now I have not had a working dishwasher for two years and this just added salt to my wound. I called Maytag furious that this keeps happening with new products. The only thing they would offer to do is for me to purchase an extended warranty at $350.00 and they would have a repair guy fix the microwave. A brand new microwave would cost the same thing???? They flat out told me that there was nothing that they would do for me, and that they were not going to fix it for free.I filed a complaint with them and never heard back from anyone at Maytag. It seems strange that the control panels craps out within one to three years on two of the four Maytag products I purchased. I WILL NEVER BUY MAYTAG AGAIN... I went back to Home Depot and told them that MAYTAG has LOST me as a customer and that I purchased 4 major appliances from them and two stopped working with in 1 to 3 years. Home Depot was shocked and gave me $100.00 towards a new dishwasher. And I did not buy a Maytag.... I still do not have a working microwave... But when I do have the money to replace it, it will not be MAYTAG. Looking online, I notice a lot of the same complaints about Maytags control panels...... Could it be a scam on Maytags part???

Went from an old simple Maytag to newer model, but still somewhat basic compared to others. However still getting used to the water saver feature in that getting in the right amount of detergent as not to have it set on my clothes and having to put through another rinse cycle and a more slimmer agitator. But do like the Maytag brand.

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I purchased a Maytag Washer Model MVWB765FW in April 2017. Its transmission has failed, makes lot of noise. The cost to repair is about $500. for Parts and Labor, under the 10 year Limited Warranty, as advised by Factory Service. I am better off buying a new Washer for that cost. The days of Maytag reliability are gone. I would not recommend this product to anybody.

I have owned several dishwashers thru the years and my favorite is Maytag. Maytag is quiet, barely hear it running which is rare for a dishwasher, dependable and plenty of space for dishes, pot and pans etc. I wouldnt have any other but Maytag. Also has several options for dishwashing which is a big plus. Love Maytag!!!

We had our kitchen redone by Home Depot in Sept. 2006. It was gutted and all was replaced: walls, heat windows, doors, lights, appliances. The Maytag refrigerator stopped working 7 years later. I feel an expensive appliance should last longer than that.

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

Purchased a new stainless Maytag dishwasher model # MDB4949SDMO ser # F54240259 on 10-20-2015. Installed about three weeks after purchase. This unit is terrible -- has not properly operated or cleaned our dishes since installed. First service came shortly after install. Complaint was unit leaves white film on all dishes. (Soap used is cascade which was recommended by Maytag in owners manual.) Technician installed a new water fill valve because unit wasnt getting enough water. After that unit still no good as unit became noisier and noisier and still leaving white film on all dishes. Second service call: the technician indicated entire noisy pump assembly would have to be replaced and would need to order it. Third service call: the technician arrived and replaced entire pump assembly, taking the old one away with him. The technician said it will be good now. It wasnt, but at least it was quiet. That was in January 2016. This unit still does not clean dishes properly -- continues to leave a white film on everything requiring hand scrubbing to remove. All dishes are hand rinsed with hot water before loading them in dishwasher, but actually dishes are more dirty three hours later after the cleaning cycle has finished than before they were put in. After having to buy new glasses and plastic ware because stubborn white film will not come off and looks disgusting. Tried various different soaps and rinsing products to no avail.Finally contacted service department for the fourth time and today technician arrived and found the unit to be mechanically functioning as it should and can do no more to help. Said to try a product called lemi-shine. Maybe my water is too hard also he said, even though we are on city water! This is our third dishwasher at this home and have never had hard water associated issues. All I want is my full refund for this defective product and I only get the run around from Maytag. Stay away from this machine.

We bought a Maytag Refrigerator, Model MSB27C2XAMSS from BrandsMart on 2/4/2015. Today, I made my 4th Service Call for the Ice Maker not making ice. The service department has replaced the icemaker, repaired it and still does not work. When I call for service I usually have to wait 5-7 days before I can have a technician come to my home. Also, the refrigerator door does not close unless you push it completely to the refrigerator, unlike most refrigerators that I have had. I would never buy another Maytag refrigerator and certainly will make an informed and researched decision before buying another refrigerator. I am truly dissatisfied with this refrigerator and would suggest looking for other brands.

Bought new glass top Maytag electric range. Only used oven 7 or 8 times when I was unable to close the door. Had to wait 12 days for Maytag repairman. Has to order new parts. Still without use of oven. Says its a known problem the hinges holding the door arent strong enough. Last stove 24 years old. Never had a problem.

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

I had noticed the lights, such as for sanitizing cycle, hot water cycle, etc, would go out intermittently, but since the washer still ran, I was down with that. Loaded it up last Sunday, pressed the button to start and El Zippo. Nothing works. So here we go again with another crap product from Maytag. Yes, I have had this dishwasher, which was a pricier model but closeout priced, at Lowes in 2008, BUT I live alone, so how many dishes do I wash. At the same time this is the third time had a repairman out (with no help from Maytag other than trying to sell me an extended warranty for nearly $400) and these machines ought to last a lot longer than this. The part online is bad enough, $150, cant wait for the repairman to call me back tomorrow and see how much they are going to hose me for.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

Things that I have read that are true: Rips clothes/towels/sheets. No real problems with motherboard like some have stated. Bought Maytag Bravos Washer/Dryer in 2009. No real problems with the dryer, HOWEVER, may with the Washer. Had the pump go out in 2/2010 to the tune of $199.20 due to a small object in the pump. The repairman said it would just take a very inexpensive part from Maytag to prevent this. In 6/2012 washer not draining, clogged pump. All right, new to HE Washers, so told to use less detergent than detergent manufacturer recommends. $79.13 to fix clogged drain. Even though being careful with items in pockets, loose buttons, etc. AGAIN had pump go in 1/13, $214.22 (same problem cheaper in 2010, repair inflation). Wed noticed it was loud on the spin cycle (like a rocket going off) and were told at that visit the bearings would need to be replaced, and quoted approximately $280 to repair those. Havent fixed, waiting for something else to go wrong and then decide what to do with it. So in 4 years paying almost the purchase price of the unit (if I fixed bearings also). Crazy. If you bought a house and had to pay 4/5 of the house to repair it in that short of a time, no one would own a house!!!

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

We bought this refrigerator one year & 3 months ago & we have had various issues that are now no longer covered under the warranty. The pantry drawer has a peg on the side that is plastic & broke off on the right side. Will have to replace the whole right side panel. One of the door handles is coming loose which should be an easy fix, but its just annoying that it happened at all. Now the control panel is reading OFF/OFF & isnt responding at all. Tried unplugging for 10 secs, then plug it back in, but no luck. I cannot find any info online regarding this issue, so we will have to call Maytag. Hopefully, there is an easy resolution to this problem & we wont have to buy a new motherboard.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

Same issues as many others here, had to replace the main control board a couple of months after the warranty period was up. Funny thing is though, I brought the old board into my local electronic repair shop thinking it might be worth getting it fixed in order to have a spare on hand in case the new one was also short lived... He told me he examined the board and there was nothing physically wrong... The problem he said was in the programming or firmware. Unfortunately, he said Maytag does not offer an update and there is no way to clone the newer version from my new board onto the old one so it was garbage. Seriously Maytag? Hundreds of dollars later in parts and melted groceries all because you wont issue a firmware update? Also have water leaking out of the bottom of the fridge late at night so Im never awake to troubleshoot it. Considering how sporadic it seems to be, Im guessing it must have something to do with the defrost cycle... Have to figure it out though as its starting to cause damage to the floor and leaking down to the basement :( Never again Maytag.

Maytag topwasher 2011 model MVWB300WQ2, SERIAL C11271134 - Im from the old school, expecting to get my money worth. I purchased a Maytag Bravos automatic washer in 2011, now less than 5 years later, it has a very loud knocking noise during the draining and spin cycles.

Although this refrigerator is 10 yrs old it really performs well. I like the ice maker as it hardly ever hangs up, the freezer works great and the refrigerator part is really super in the veg drawer and the meat and cheese drawer. All in all this was a great buy.

Maytag MVWC300BW clothes washer makes holes in heavy duty T shirts & sheets. It stretches clothing. We are following directions in loading without success. We are washing everything on the gentle cycle twice to get the clothes clean without destroying them. Today we were stood up for our third service call.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

My Neptune has been a great washing machine. I did have to change the door gasket twice and just recently changed the bearings. My machine sounded like a jet engine. I ordered the parts on eBay, watched a YouTube video, and fixed my Neptune washing machine. Its still working and runs quietly.

We used to own a Neptune Model. After always leaving the door opened and following the recommended monthly cleaning and many extra cleanings with diluted bleach and water, we could not get the smell out. We paid for a new seal, Advice from Washing Machine Repair service even though we paid a lot for an extended warranty. We had to pay for this ourselves. We also had our year to year maintenance. Because we could not fix the issue, nor would MAYTAG, we donated the set to donated it to Salvation Army.We decided to give MAYTAG another chance, so we purchased a brand new FRONT-LOAD WASHER and DRYER in 2014. As I would repeat the same regiment, I would notice little black specks, so I would clean it an extra time with Afresh. I have continued to this date, repeating the same regiment of keeping my washer clean and serviced as we should, I now have the whole tray dispenser spotted with LARGE black goo that smells. So I have continued to clean my Washer.After returning home from the Cleveland Clinic, I was ready to do our laundry from the trip, more black goo and smell coming from my Maytag front-load washer. My sister had stayed with my 86 year old mother and had wash a load of towels while we were gone. She left the door opened also as she was instructed many times, and that is how we found it. So I took the dispenser tray out as usual and bleached it and scrubbed it. As I did this I noticed bigger areas of goo. I looked in the dispenser housing and OMG it was covered with black mold. I am appalled that our $900.00 Washing Machine is like this. This IS BLACK MOLD, There is no way to remove this mold. I have the sides and bottom cleaned with bleach, BUT I cannot get into the multiple crevices.I called Maytag and I was initially told by a Maytag Customer Service Person said that it sounds like BLACK MOLD and MAYTAG COULD DO NOTHING! I asked to speak with a supervisor. At first she seemed a little put off, but as we talked she became more pleasant, I offered to send pictures or a video of the WASHER WITH THE BLACK MOLD and she said no. She told me to pour bleach into each dispensing compartment and the drum. Then run a wash with no clothes on all HOT WATER 2 times, then rinse 2 times and this should get rid of it and to also leave the dispenser drawer open a crack as well as the door after each wash.The Supervisor said ok and thanked her for her help. Then she said good luck and thanks for calling MAYTAG. Ive did and already do everything our Washer manual says to do on cleaning and maintenance of my expensive Maytag Washer and dryer. The manual says nothing about leaving the dispenser drawer open a little so it dries. The bottom of the housing looks great from doing this, along with me scrubbing it until 5:00 am with diluted bleach water. However, in the MANY SEAMS, CREVICES, THE SCHUTE AND POSSIBLY THROUGHOUT THE WASHING MACHINE IS BLACK MOLD that we cannot access without disassembling the machine and voiding our extended warranty.MOLD GROWS RAPIDLY and causes many illness. I already have an ongoing illness since childhood, I take care of my 86 year old mother, my husband just finished cancer treatment in January. We certainly do not need any other health issues. I called my local Appliance repair company and they said that they normally do not handle anything like this, but if my husband couldnt take the outside of the machine off then the top I could pay for a repair person to come out to take it apart then call and have them come back to put it back, pay them again to reassemble our Washer.I believe Whirlpool in its purchase of Maytag has taken a Monkey on its back. Maytag will do nothing, why should they? They already have their money from when we purchased our machines along with money from many other consumers who also have ongoing issues with their WHIRLPOOL/MAYTAG Front-Load washing machines. It is undignified and deceitful how they treat their consumers with such disregard when we have filled their pockets by being loyal customers.Word of mouth is good or bad advertisement for any company. Everyone who has unresolved issues of any kind can write a formal complaint to the CEO and President of Whirlpool/Maytag. The address is on the internet. Shame on Whirlpool/Maytag for taking many consumers hard earned money, when apparently some of Whirlpool/Maytags money is ill gained by developing and manufacturing a consumer product that causes black mold and marketing it to sell to us, the consumer. THIS IS A SERIOUS ISSUE WHIRLPOOL/MAYTAG. OWN UP!!! My advertisement begins today!!!

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

Series 200 dishwasher wont start. Just over 1 year old. Control panel needs replacing which I found out, is a constant problem and a design flaw. Called Maytag and they would only offer 25% off new part. Why would I do that when it is just going to go bad again?

I seem to be just another unhappy Maytag microwave oven customer. The SE code indicates a bad/faulty/short in the keypad. It seems this is a very common issue so buyers beware! If I dont get this resolved, I will no longer buy Maytag/Whirlpool products.

Does a good job of cleaning but takes much longer to complete. Pretty much standard features. Has rinse only cycle, air dry only cycle, and cycle for pots and pans. Top rack had special holders for long stemmed glasses which I dont need. Standard size. Same size as my Kitchen Aid. White, front load, no special appearance. It takes much longer than my old dishwasher. Also the soap dispenser broke after 2 months and had to be replaced. It requires that two buttons have to be pushed to start. My old one only required one. It does a good job of cleaning.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

We like the refrigerator and we have had it several years. But the thing the top freezer conceals much of the top rack of refrigerator. We must duck and almost kneel to get to food inside. Next fridge will have drawers and doors that open on both sides.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

My dog had to be on a special diet to recover from a stomach disorder. I placed 1/3 cup of dog food plus chicken broth and baby food in a bowl. I intended to heat it for seconds. Minutes later, my dog was whining and sneezing. I immediately returned to the kitchen to find the food and bowl were completely charred. The biggest problem however was from the plastic splash guard that melted down. Smoke filled my home. I had to call the fire department. I was coughing and had difficulty breathing. The smell was horrible!The insurance company and I have had thousands of money in restoration cost due to the damage. I was out of my house for weeks and got very sick due to returning to the home that was not remediated properly (allergies and asthma). The microwave was an over the range Maytag MMV4205BA. I would like to find out if the fire was due to a malfunction in the microwave oven. If so, Maytag should be paying for the damages. I still need living room furniture and carpeting replaced due to smoke damage.

We purchased our Maytag Washer back in August of 2019 and already needs a Motherboard and Lid replacement. Not only do you have to wait almost an hour to get a hold of their customer service I got hung up on once after waiting that long and the a Customer Service Lead by the name of Brittany couldnt offer any help either. We have been without our washer for almost a month now and will have to wait another couple weeks for the part to come in on top of probably another week for a maintenance person to come out and repair. I asked to expedite the part but that went absolutely nowhere. It actually added time to get the part because it was suppose to be here on the 13th but now its up to 9 business days for that to happen. I would stay away from purchasing any appliance from Maytag with the experience we have gone through and terrible customer service as well.

Maytag Bravos Quite Series 300 - We purchased this washer from Lowes on 9-20-11. Weve had trouble with the spin cycle on this machine since we purchased and in December 2014 the washer stopped working and showed the symbol F:51-no part, to be found waited a month for the part; repair fixed and the machine stopped working in FEBRUARY AGAIN same part-still not fixed. Ive always purchased a Maytag but the new washer Im in the market for will not be a Maytag.

My husband and I purchased both a Maytag washer MVWX655DW1 and dryer MEDX655DW1 less than 3 years ago from Sears. We had both the washer and dryer professionally installed. Yesterday, we had an authorized service man come in and look at the problems we were having. He told us our Maytag washer would need a new gear case and gears costing $750.Our Dryer, same age, needed a new cycling thermostat. He said it was due to not cleaning out the lint trap. My husband and clean the lint trap after every load religiously. He said there was a pile of lint built up in the dryer. I could only think this would be a design flaw. To repair the dryer it would cost $350. The grand total to repair our Maytag Washer and Dryers would be $1100. We paid $1082.38 at Sears for both. The only thing Maytag offered to cover was a part for the washer which would cost $640 and we would need to pay the extra $110 for service in addition the $150 diagnostic charge, due to use being out of our one year warranty.We decided to not fix this machine to avoid similar problems in the future. I talked to customer service and asked them to cover the diagnostic charge instead of sending the part, which is far more costly. I got the runaround and 3 rejections before they finally agreed to pay for the diagnostic charge. My husband and I are extremely disappointed in this experience. We currently own a Maytag Microwave and Electric Glass Top Range. We will never buy Maytag again. Our Stove is also lacking. We have the AquaLift cleaning stove. The AquaLift technology does not work.

Maytag Model # MMV4205DS - First Maytag microwave lasted just over a year before it quit. Replaced with same model to avoid install hassle and 1 year and 4 months later got the dreaded open and close door message. Read so many horror stories about repair service for Maytag that I decided not to bother and purchased a GE. I will never ever, ever buy anything Maytag ever again...

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

We purchased a Maytag Dishwasher (model number mdb6759aws3) about 3 years ago. After about 1 year, the control panel started to go. Certain options would not light up. If I used the options that did light and shut the door, the dishwasher would work. I had called Maytag, and they were charging almost $200.00 to come out to repair. Now after 3 years, the entire panel is out. We had someone come out. We ordered a new touch pad for $265, and it still did not work. It is the control panel that is dead. What bothers me is that after reading online, this seems to be a continual problem, and Maytag does nothing to help the consumer.

I am in my 24th year of using my Maytag washer and dryer. The set was purchased in 1996, so it has been well worth the money. At this time, it does not spin out as well as it used to, but I just fluff the load and spin it again and then it is ready for the dryer. I have been very pleased with the set and have never had to have a repairman work on them. Cant ask for more than that!

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

Bought a Maytag front load washer and dryer, it rattled and shook from day 1, they have come out 3 times in 1 month to fix that, now it wont even spin. This will be the 4th day of work I have had to miss, and all they say is, We have to send someone out to repair. Sorry. Do not purchase their products!! They dont care.

A company who sells a washer that makes washcloths/towels smell musty as you take them clean from the drawer should be ashamed and refund everyones money!!! I have always love Maytag/Whirlpool products until this piece of trash washer. My husband, who is retired from Maytag, gets a very nice deal when buying their products under the VIP program. However, how nice a deal is it when you have musty/sour smelling towels after washing??? Ridiculous! Seems that when the washer went to no agitator and water/electricity saving they forgot what the purpose of a washing machine was. Im very upset and would NEVER recommend Whirlpool/Maytag products to ANYONE!

This model MGR5875QDW range is very difficult to use. When you press broil for instance, the display says set. There is absolutely no indication of how to set. Therefore, no broil. The same thing happens when you try to use the clean function. It is virtually impossible to use the control panel; it is just too difficult. Therefore, most of the functions are not usable.The kicker though is that the handle comes off. During the extended warranty period, a technician came out and fixed it. The toughest part of this job is to get the oven door back on. I tried for 2 hours everything I could think of. Then, I got an idea to use Maytags live chat. They told me that I would have to call for service and pay for a service call to get the door back on. I told them that their clean cycle is too painful to use, so I am assuming I am not the only one who has removed the door to clean the oven. Pay for a service call every time I want to clean my oven or fix their defective handle design because the handle falls off every 2 years? That is not acceptable.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

My 1 year old Maytag Bravos 300 dryer caught fire on Nov. 21, 2011 after the first one was replaced. Firemen came. Luckily, it didnt spread to the house. The first one wouldnt dry my clothes.

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

Ive owned my Maytag Neptune front loader since 2003. Since then, the whites have either turned gray or yellow. Ive tried minimizing the use of Tide HE, maximizing its use, and I still get the same results. Can anyone please assist me with this major problem? Ive owned Maytag appliances since the mid 60s, and I know the quality isnt there anymore.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

My Bravos Washer and Gas dryer are only a few years old, and they have both been problematic to say the least! Neither Home Depot nor Maytag have been helpful. My washer has had the shocks replaced already, because it would constantly go off balance and shut down and they cant grease the bearings because they are sealed. So, now it sounds like an airport is in my laundry room! The gas dryer takes an entire day to half dry a load and its burnt on the inside!

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

It does not matter what mode you select, every single piece of clothing comes out a scrunched up wrinkled mess. I have to wash all clothing in bulky sheets mode because it is the only mode where the clothing actually gets submerged in the water. This washing machine is extremely loud and it is without a doubt, the worst purchase I have ever made. I have never written a review before, but this product is so horrible and frustrating. If I can persuade one person not to purchase one, I feel that I have done a good deed.

Our washer/dryer combination (2005 Maytag Neptune MLE2000AZW) has given us nothing but problems. The main problem is the stink from the washer. The unit is no longer usable and we are searching for a top loading unit to fit in the space. I am so angry - how did this piece of junk ever pass Maytags quality control?

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

Have had Maytag HE washer for 4yrs, so far it has broke down three times. I contacted Maytag and they asked if I had bought extended service contract? No I paid $700.00 for this washer and had expected it to work a little longer than 2yrs before seal in door is cracked. Would NEVER buy another HE or Maytag product again!

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

I really love my front loader and it has no agitator to rip pockets and tear off buttons. The tub is very large and I can wash king quilts. I do miss being able to fill the tub and put in additives and then add the clothes to soak.

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

I bought this Maytag dishwasher model mdb6709awq1 from Home Depot that installed it; they did a good job installing for a fair price. My gripe is with Maytag. I have owned a Maytag dishwasher since 1977. Back then it was the best you could buy. Since Maytag sold out to Whirlpool to save being bought by the Chinese, the design of the dishwasher has lost or gave up their unique design that made it so good and dependable. The inside of the rack/drawers has been totally changed. It used to have fold down racks on each side of bottom rack that was great for coffee mugs, small bowls/containers, and they came out sparkling clean. The utensil basket was centered front and again the utensils came out super clean. Maytag sold their soul when they sold out to Whirlpool. Dont know if that was part of the deal that they give up their unique design or why did they change the rack design. I wish I still had my old Maytag from 1998 that yes, worked without a problem, then I sold the house with the dishwasher. Why is it that so many appliance makers have taken dependable workhorse designs and phased them out? What is wrong with an appliance lasting for years, decades without problems? Only thing I can think of is that they wont make millions every year as they only would sell so many a year if they are dependable as they wont need to be replaced.

Maytag dishwasher model #MDB7609AWB2 - The control panel on this dishwasher has just gone out for the fifth time since 12/10. Last time I also had to replace the control board also.

I have had my Maytag refrigerator for eight years and it is best one I have had in fifty years. It is dependable, quiet running and easy to maintain. The ice maker is wonderful; it always has ice ready even on the hottest summer day. If and when I ever need to purchase another refrigerator, I wouldnt hesitate to buy another Maytag!

I changed from another HE brand to this model. No comparison. This machine can do twice the work... but double the time. My former machine was quiet while this one is not. Maybe I got spoiled to the former brand, but Ive never heard so much noise from a washing machine! Ive always thought Maytag meant quality but I think they may have missed the boat here. I tried reviewing on their site but when I gave it two stars, I got an error message. Clever, Maytag.

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.