I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

Maytag MVWB835DW was less than 2 years old (purchased 1-14-16) when it began to fail. Maytag sent repairman out, he declared it beyond repair. Machine locks, washes and adds more and more minutes and cant turn it off without unplugging 5-10+ times... sometime takes a week to get clothes out of machine because of locking itself. I have extended warranty and yet when I try to contact Maytag, to have them honor this, there is eternal wait on phone, online, no help whatsoever. I read via Consumer Affairs that there are almost 3,000 reviews on this specific machine being a problem yet amazingly the Maytag man never responds! I have spent many many hours with no resolution. Amazon says so many reviews have been written about this, that they are unable to take my review because of excessive reviewing.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

Maytag Bravos XL top load. I purchased 2014. Three years old drum bearings went out, just two people in home. Very expensive to repair. Three years later I hear bearing going out again, in mean time had a F51 pop up and that means major failure call for service. I called Speed Queen and ordered a machine with all metal parts delivered the next day, and it is Made in America. I had purchased Maytag because of name but I will never purchase another Maytag. My friend had the same experience same time frames.

I purchased this Maytag Bravos Xl Top Loading Washing Machine approximately 2 1/2 years ago. It broke down shortly after the 1 year warranty was up and cost me $300.00 to fix. A bearing had broke and needed a service call to repair it. Well, I paid about $800.00 to begin with, so decided to fix it. Today it started draining water from bottom of it. I call Maytag and after a 20 minute wait on the phone because they were having higher than normal call volumes! They cannot help me, other than to charge me for yet another service call and perhaps a repair. Whirlpool/Maytag makes a high priced money pit of a washing machine! Dont waste your money!

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

Maytag has really gone downhill. Had trouble with a factory defect in a new French door Maytag refrigerator within a few months (had it returned) and now the Maytag Centennial EcoConserve Top Load Washer no longer spins after only just barely 2 years of use... I will NEVER buy Maytag again. That is a promise. I will put more money and buy more expensive products from your rivals if it means avoiding Maytag products. That is my advice to anyone reading this review. The washer was used for MAYBE 10 loads of laundry per month... Yes, just for two people who have desk jobs so It was never stressed out. Used HE laundry detergent. Quality is a thing of the past for this company. Your reputation is in the doghouse.

After reading several of the reviews, it looks like Maytag doesnt get it - or maybe they do and its a plot to make more money. Our dishwasher model MDB8959FSZ4 was installed in Dec. 2016. Within the year, it started leaking. After many service calls it was determined that the arms holding the upper rack were not installed properly and were pushing against the door and water was coming out. After that was replaced, weve had 2 years of relative good use. Now, it wont empty and that started after smelling something burning. The burning smell has gone away but it wont complete a cycle. Service tells us its the drainage pump and that will cost nearly $500 to replace. We wont be spending another dime on this piece of crap. Well replace it with NOT A MAYTAG. Im wondering if it has to do with the control panel as many others have mentioned. We dont care to find out at this point. We are buying something else.

I purchased a Neptune front-load washer in November 2005. Now that its out of warranty, theres nothing that Whirlpool can do for me. The front panel of the washer that surrounds the door has been rattling for a few weeks, so my husband took it off and found a crack on the top right section of the panel where its bolted to the frame. There is a rust bubble where the crack started. We couldnt see any of this until he took it apart. The cost of a new front panel is $185 and the response from Whirlpool? They are “very sorry” that this has happened, but there is nothing that they can do. Oh, really? Well, I come from a long line of Maytag owners and there is something I can do: spread the word about the disgusting piece of junk I paid $1,100 for! This washer wasnt even made here - it was made in Korea and its not worth $100! Note to Whirlpool: your customer service sucks!

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

Maytag Bravos Quite Series 300 - We purchased this washer from Lowes on 9-20-11. Weve had trouble with the spin cycle on this machine since we purchased and in December 2014 the washer stopped working and showed the symbol F:51-no part, to be found waited a month for the part; repair fixed and the machine stopped working in FEBRUARY AGAIN same part-still not fixed. Ive always purchased a Maytag but the new washer Im in the market for will not be a Maytag.

This is an awful product. I bought this product from Best Buy at the beginning of August 2018, and can no longer return it because it’s past their 14 day return policy. This washer does not wash clothes well. No matter what setting it’s on, clothes come out looking dirtier than prior to washing. Maytag should do what is right and refund customers for this worthless purchase.

Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

I purchased a Maytag dishwasher in Jan 2012 at Home Depot. It ran fine for 1 and 1/2 years and was only used 2-3 times per week. I returned from vacation and now needs a new control board at a cost of $300. I felt Maytag was a reputable company and am very disappointed. I am a senior and on fixed income and now sorry I chose a Maytag. I will get it fixed this time but that is the last money I will invest in Maytag appliances and repairs. I worry that the washer and dryer will go next as they are also Maytag and are just over 1 yr old.

I am submitting this review today to express my disappointment with my Maytag washer. This is the Maytag MVWX655DW (Bravo), with Serial# C61842055. In August of 2016 I lost many treasured items due to a flood in Lafayette, Louisiana. My daughter and I were devastated and displaced because of this event. This is also in addition to completing Cancer treatment 2 days before the flood.I lost my GE washer which was a great product. It was a struggle for a long time, but we were finally get back on our feet. I was able to get another place to live, and it was time to purchase a washer. I was told that Maytag was one of the best products on the market, so I decided to purchase my first Maytag washer. This did not turn out well for me, and it was very disappointing. After 9 months of ownership of this product, it is broken! It is my belief that the product may have been defective.I put in a service call, and had a repairman come to my apartment on June 19th. I was told that my washer needs several parts to repair it, including a pump. I have never had this issue with prior washers. My previous washer before my GE purchase survived for over 10 years before it has had any issues. I called on June 26th to ask about Maytag issuing me a new washer or a full refund, instead of repairing this faulty product. I was told no, and was offered and extended warranty for 6 more months and $75.00. I expressed to her that I would rather have a new washer.The Bravo Washer is a very bad product. Instead of taking advantage of customers, Maytag needs to stand by that 10 year warranty sticker on the washer. Please understand this purchase is a LEMON. This washer did not last a year. After all I have been through, I did not need this financial hardship. In the long run, this product will die again. Unfortunately for me I may not be able to afford to purchase another washer. I am still getting follow-up treatment for my Cancer, and it is very expensive. Can someone please re-evaluate the need for a replacement washer or offer me a full refund? This product should not be broken after only 9 months of service.

My built in electric double wall oven, Model MEW6630DDB, convection on the top, has been the most frustrating appliance I have ever owned. It has never kept an even temperature. It has been repaired several times and still does not keep an even temperature. It takes 14 hours to cook a 20 lb. turkey and baking cookies are not even an option. I have complained to Maytag and have paid for repair services. Their solution buy an extended warranty which is absolutely insane because they havent been able to repair it since it was new over four years ago.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

I bought my Maytag Quiet Series 300 about 6 or 7 years ago. About January this year the clean light quit working but the dishwasher was still doing its job. Every once in a while the clean light would come on again and then go away. I did not worry about this as the dishwasher was still working despite the absent clean light. I did call Maytag and told them about this. I believe I even asked if they (customer service rep.) had heard about this and was told no. Last Friday the start button no longer works which means the dishwasher will not function. Some of the other lights/buttons work but not start or clean. I have dealt with Maytag repair service/customer service before about my Maytag washer. I know they are not much help and I always end up paying a lot of money. I am not interested in calling a Maytag repair person in and paying from what 300.00 to 400.00 dollars to get it fixed. Past experience of others seem to prove that it will break down again. Last Maytag appliance that I will ever buy. I used to be a loyal customer. I want to join the class action suit. Please tell me how I can join.

In 2011 I bought a brand new Maytag (HA!) washer & dryer thinking it was going to be as good as my old Maytag - which is STILL working since 1980 in a 4 person household! Boy what a HUGE mistake that was! In 2 yrs the bearings went out and something else - big! and would have cost more to fix than the NEW Speedqueen I got (which does a HELLUVA better job and by far all around is better than Maytag CRAP!) AND has a 3 yr warranty and not just 1 like JUNK Maytag! Maytag name went down the drain with the dirty laundry water! FOREVER! Seems the more I look around the more complaints I see! Whoever owns this brand now should be crawling under a rock somewhere and be ASHAMED of the POOR quality products youre putting out there!

I have a Maytag Bravos washer and on almost every other load, the dark clothes (mainly slacks) come out with white splotches on them and then I have to re-wash the pants and the splotches go away. What could be causing this? Im tired of washing clothes more than once. Its incredibly wasteful and bad for our environment. Thank you.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

Got the dryer free when we moved into our townhouse. We had been doing 2-3 loads a day for almost 8 years. The dryer was old when we got it. No complaints. Just wish there was some way to fix it. But mechanic said, No way. Almost a valued member of the family. Say 2 loads a day, 7 days a week, 52 days a year. This is a lot of loads. Remarkable. New machines cant do that today says our mechanic, they are not built to be fixed. Now, when broke, replace, don t fix.

This machine sucks. Im down to washing three to four items only on an extra capacity machine because every single load becomes unbalanced. Feeling the weight of each item and then placing it correctly doesnt work. Repairman came out. Said it was balanced. Lie. At this point I want to take a sledgehammer to it and send the pieces one by one to Maytag. They should be embarrassed to even have this product for sale to the public with their name on it.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

Centennial commercial tech. washer - We purchased this piece of junk in Sept 2013, and had to have a repairman twice before it was six weeks in my home. I wrote several letters but the only thing that I received were applications for insurance to cover repairs. I should have received a replacement as it was bad from day one, but Maytag doesnt replace!!! Its been semi-reliable for the past several months, until early this year. It started jerking when it changed cycles, sounding as if the drum was hitting really hard against the sides. It has continued to do that regularly; now it wont function on the cycle its set on. It wont spin, sometimes the lid lock wont work. It starts filling when it should be draining. This evening, it stayed in the rinse cycle for 40 minutes and when I realized it was still rinsing I had to unplug it to get it stopped. It goes on and on, (and so could I out of frustration). The good name of Maytag has turned to trash, and when it leaves my home, no more Maytags!!! PS. The dryer we got with it takes at least 1 1/2 full cycles to dry a load, and since I couldnt get it to spin properly, Ill be lucky to get this last load dry in 2 to 2 1/2 cycles.

I have a washing machine that I purchased in August 2010 that is not working. A certified Maytag technician came out and informed me that the shifter assembly went bad and needs to be replaced. The machine is only 19 months old and they are telling me it will cost $352.25 to replace this part. I only paid $549 for the machine. This was a poorly manufactured part and a very expensive repair for a newer machine. This part did not give out to normal wear and tear. I just spoke to a supervisor at Maytag customer service and she said Maytag would not replace the part or offer any kind of discount. I am so disappointed in this answer and type of customer service from a major corporation. I am willing to pay for the labor (not that I should have to), but had hoped Maytag would at least help with the cost of the part. Basically, Im out of luck because the machine is no longer within the one year parts warranty. I will never buy Maytag again.

A month ago I purchased a 25 cu ft side by side. First the recirculating fan quit. It was repaired. But the water and ice hose in the door froze and cracked the entire freezer door. Must be replaced, unfortunately they dont have any, so I was quoted 6 weeks for a new door, that has turned into 12 weeks and they cant guarantee me a date. I requested a replacement fridge and was told, They cant do that. I purchased the full Maytag package - stove, dishwasher, microwave. I expect better customer service than that, Take a door off the assembly line and ship it to me.

Like so many other consumers, I was drawn to the Maytag name because of what I thought was the high quality of their products and their stellar reputation. So when our old wall-mount oven failed, I sought out a replacement from the Maytag line. I purchased a model MEW5530WDDB17 in 2011 and had it professionally installed. It worked well for a couple of years. Then, suddenly, three of the numbers on the digital control panel stopped working, making it impossible to set the oven to any temperature that included a 4, a 2 or a 5. When I contacted Maytag, I was informed that the unit was out of warranty, but that I could schedule a service call. I had already researched this issue online and knew that the service person would inform me that I needed a new control board and that one could be installed for around $300, and that the new board would come with a 90 day warranty. When I asked the person to whom I was speaking, she said that she had no further information for me. I know that a lot of others have had this same issue with their Maytag range/ovens, and many of them agree with me that we will never purchase another Maytag product.

Horrible Refrigerator MSB27C2XAM00. I bought this refrigerator November 2013. Over the past 5 months I have made over 10 calls to Maytag customer service. Each phone call averages 30-45 minutes in length. In total I have and have had 6 service repair visits. Within 4 weeks of acquiring the unit, the letters on the ice/water dispenser wore off. They replaced the panel and within 4 weeks the letters wore off on the replacement panel. The subsequent calls made to customer service were regarding slow water dispensing and shrinking ice cubes. I was advised in order to maintain water speed and decent sized ice cube production I would have to replace the filter every time the water dispensing slows, which is on average every 4 to 6 weeks (each filter costs $40).When I asked why I would have to change the filter so frequently when the packaging instructions with the water filter states you can expect an average of 6 months use or 200 gallons, (mind you we are a family of 2 adults and one child under the age of 10 surely not consuming 200 gallons of water within 4 weeks), Maytag advised me to attain a whole house water filtration system. I was told that the water supply to my home must require extra filtration which is why the filters are not lasting. I asked if other NYC residents have made such complaints. Maytag advised they cannot share this information for confidentiality reasons. I told the rep that I did not want specific names/address of the complainants. I just wanted to know if there were any other similar complaints! If its the NYC water supply I would have to believe there would be similar complaints. Maytag would not advise.They will not budge in replacing the unit. After spending $1,400 on this refrigerator I am now expected to invest $500 annually on water filters in order for the refrigerator to work properly. I was also advised that if another service tech came to my home and the issue was found to be the same I would be responsible for payment of the service call. I did my research before purchasing this Maytag product. I ultimately selected Maytag for their reputation. I am so disappointed with this unit and with the company that I will never purchase another Maytag appliance and I will advise everyone I know to never purchase from this company again. Such a disappointment!

I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

We have owned this range for a little over a year. Oven will not hold correct heat. Have temperature sensor replaced under warranty. Did not make any difference. You can adjust temperature up or down according to actual temperature readings, but the temperature swings so much that it is worthless to try. Very hard to get food baked right.

Do not buy this dishwasher unless you get the extended warranty. We purchased this dishwasher in Jan 2014. The first one delivered was completely busted up (which was probably the delivery companys fault for not handling it correctly). Then we had to wait for the replacement one to come in to get installed. In Sept 2014 the control panel stopped working. It was repaired under the warranty but it took several weeks for the authorized repair shop to be able to come out, diagnose, order part, and then come back to fix it. Now March 2015 (5 months later) we had the same exact problem with the control panel. The repair company was unwilling to order the part to bring with them even though they already had it in their records what we needed due to the previous repair. It was going to $300 to repair it since they only warranty the repair for 90 days. We decided to replace our 14-month old dishwasher rather than put any more money into it. Shame on you Maytag for putting out such a bad product - obviously this is a common problem. It is quiet and does a good job of washing but to have it take several weeks to get a repair done combined with having a problem that cost 50% of the purchase price to replace twice within a year of each other, absolutely not worth the money. Should have just spent the extra on a higher quality product. Will definitely get the extended warranty on whatever we replace it with.

Maytag centennial washing machine - I am pretty good as a mechanic or this machine would sit unused. Purchased in 2/15 at lowes. Poor installation. Then the machine... I hooked it up properly and ran it with extra load setting to see the machine develop a life all its own. The sheet metal breathed in and out like the chest of an old man running uphill. Lower exit hose not properly installed leaked on floor so I put on a new adjustable clip. Machine can only handle small loads. While it does wash clothes (it is a washing machine!) it requires close supervision in size of load. The machine needs a plumbing bang pressure gauge or you are likely to blow out your water pipes. It sounds like there are a bunch of people walking the machine with ball peen hammers. Who cares, but they were made in America and moved to Mexico. They should need visas to get back in. Absolute junk.

I have a Maytag washer that I bought new in 1995! It is still washing my clothes like a champ. It must be true - the Maytag repairman is a lonely soul, in all these years I have never had to call him!

Wish it was a French door style instead of freezer on top. Not good if you are tall. Other than that we are pleased with it but will look to trade for a French door style.

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

We bought a Bravos model in May 2010. Two years later, the machine started making noise during the final spin cycle. We finally called a repairman who came today and informed us it was a bearing in the outer drum. The cost for the part (the drum assembly) was $290, not to mention the cost for labor. Since we only got the original warranty, the service center at Maytag refused to help with the repair. We, as others who have had problems with Maytag, bought the washer because of Maytags reputation. This is why we have to buy extended service warranties. Companies make trash! What happened to the days when an appliance lasted longer than 10 years? Why cant we buy a good sturdy appliance without superficial bells and whistles? We have no idea if any other brand is better, but we will not buy another Maytag.

I purchased a Maytag front loading Epic z washer and I paid a great deal of money for it and now I have a broken part on it. We contacted the Maytag manufacturer and they have informed me that the part would not be available for up to two months maybe 6 months. I cannot afford to buy another washer, so now I have a broken washer and need to purchase another washer until the parts come in. I would not recommend this washer or dryer to anyone ever.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

I purchased a Maytag MDB7749AWW dishwasher in March of 2012. The electronic control on this unit failed in June of 2013 (3 months out of warranty). I have been trying to get a replacement part for over a month; the part is on backorder and unavailable. Whirlpool is unable to tell me when the part will be available. So, I have had no dishwasher for over a month and have no idea when, or if it will be repairable. Additionally this part is $150.00 and another $75.00 to have it changed. So it is going to cost me $225.00 to repair a 15 month old dishwasher that I paid $450.00 for. I have received ZERO support from Whirlpool. They told me today, 7-31-13, that the part is still unavailable and they will notify me in 3-6 business days as to if they can find a part. After seeing all the issues other people have had with this part, Whirlpools total lack of concern or support for the consumer and the cost issue it makes no sense to repair this unit only to see it fail again in a year or so. Basically I have a $450.00 boat anchor. The retailer purchased it from feels bad and is offering me another manufactures machine at a reduced price. Maytag has refused to do anything for me. I will never buy another Whirlpool / Maytag item again and I do intend to add my name to the pending class action suit.

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

Our Maytag refrigerator is leaking water all over my kitchen floor to the point that my floor tile has lifted. The ref. is a French door with water and ice in the door and freezer on the bottom. We have been cleaning up puddles of water at least several times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasnt ConsumerAffairs demanded a recall on these expensive defective refrigerators to date? I am truly disgusted.

In late March or early April 2010, I purchased a Maytag Microwave from Sears in Ocean, New Jersey. The microwave was installed by Sears technicians on April 9, 2010. The total price for the microwave and installation was $356.53. I specifically purchased the Maytag brand because of Maytags longstanding reputation for quality products with long lifespans.On October 5, 2014, the microwave became inoperative and displayed a code of SE. On or about October 9, 2014, I contacted Maytag Customer Experience Center, via email, and advised them of this problem. I also wrote to Maytag explaining the situation. On October 15, 2014, I was advised via email that, as my warranty had expired, any repairs were my responsibility. I requested that my email be forwarded to Maytags CEO for consideration and review and was advised on October 20, 2014 that a Maytag supervisor would call me within two to three business days (of October 20th). After a follow up letter to the CEO, I was again advised on October 28, 2014, that the microwave was out of warranty and any repairs were my responsibility.I should add that I contacted Maytag Repair Service and was advised that the price of the repair far exceeded the price of the microwave. I feel that four years is not the expected lifespan of a microwave, especially a Maytag, and can only conclude that the Maytag microwave which I purchased was defective. I have purchased less expensive microwaves that have lasted for at least ten years. I got absolutely nowhere with Maytag personnel, found them to be curt and dismissive and would NOT purchase another Maytag product nor would I recommend them. Buyer beware - Maytag is not what it used to be! Very disappointing.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

We purchased a Maytag dishwasher & installed Aug 15 2012. After installation the control panel wasnt working & Lowes replaced the dishwasher with the same model. After the years warranty was up I started having trouble with the second dishwasher panel. I limped along with it for months until I could not get it to work at all. A repairman came and said that the touchpad & board was damaged. He said it wasnt hooked up properly. After an estimate of over three hundred dollars we decided to rid ourselves of it and purchased another, cheaper brand. Was out 79 dollars for the repair estimate & over 500.00 for the Maytag dishwasher. Plus a new one installed for 700.00. Had the use of this appliance less than two years.

The Maytag Washer and Dryer we bought new and they have been great. The dryer was bought in 1972 and still works well. The washer was bought in 1997 and still does a good job. We are satisfied with the long time these 2 appliances have lasted. Do any appliances manufactured today last that long?

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

Very poor quality. Vegetables freeze at the back of the fridge I have tried everything. The vegetable drawer constantly comes off its track and the freezer door slide jams and stops the door from closing. It leaves about 1/2 inch gap. Now the Whirlpool/Maytag company changed their corporate policy and wont allow an appliance store that to come out and fix the fridge I have to go back to the manufacturer. Their website wouldnt take my email address when I tried to sign up for an account and they wont answer the phone. What a hassle. Ill buy another brand next time but never GE or Whirlpool again!

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

My wife and I bought a Maytag Bravos at the suggestion of a store employee at Lowes. Since we have owned it, I have seen the reviews and the washer has been a total let down. We have experienced all the same complaints. Loud noise, door lock not working, not enough water in the drum to wash clothes, and the bearings going out and it doesnt work. NEVER will we buy a MAYTAG again. To the scrap yard I go today. Thanks MAYTAG for wasting my money. Thanks LOWES for recommending this garbage.

Dryer doesn’t wash all the clothes and the dryer doesn’t dry anything correctly. All, regardless of materials or size of load, comes out damp. Repairman’s excuse was that it’s a learning curve(?) and our dryer vent was the cause (which it wasn’t as we had it checked out and there was nothing in it) and that was it. Very disappointed in the washer and dryer and now the company where we bought them as it seems that we’re stuck with over $2K worth of equipment that doesn’t wash or dry well. We’re awaiting to speak with manager for a replacement of anything not Maytag. Not holding our breath and definitely not a happy customer.

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

From day one I didnt like how this machine restricted how I can wash my clothing. There is no water volume controller. It is all automatic, which sounded fine in the store, but once I used it I quickly realized it is horrible. I can not add extra laundry or detergent in at the last minute because it says not to open the lid at all once you start the load. The settings are very glitchy. They do not seem consistent. There is a knob for level of soil on the clothing which doesnt seem to do anything at all. Ive had it now for four years and it has only gotten worse. Now I can only use one setting Hand Wash. Try doing a teenage boys clothes in Hand Wash and youll find out quickly that nothing gets clean that way. Oh, and all of the sudden the spin cycles are not working, they spin when they want to but they rarely get rid of the dirty water. Spinning in dirty water does not get clothes clean either. This machine is horrible, hands down, the worst washing machine I have ever owned.

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.

Oven was purchased and put in May 2014. I have not be able to use. The oven temperature is off. If the oven is used at 500 degrees the temperature is really 900. I thought I had a gas leak because I got a bad headache because of the smell. The gas co told me to get a repair person to look at it. Maytag has been horrible to deal with. I have taken 3 separate days off trying to get it fixed. The last Maytag repair man had the nerve to ask me where the gas line was. He shut the wrong off and had a gas leak in my house. I had to open all windows. He was supposed to come back the next day. He did not and I received no calls. I have paid for an oven that is dangerous that I cannot use. I feel Im being treated this way because I am an older woman. I will never buy another Maytag.

Maytag Bravo model MVWB750WQO. Bought this washer in 2009 for 1300 thinking it would last at least 10 years! Wrong! I loved it until a few months ago when it started making VERY LOUD noises during final spins. Sounded like the house was going to take off. Then today it started leaking water. Repairman said it needed a drum, seal and gasket. Would have cost 700-800 to fix. Needless to say we bought a new washer today, and it wasnt a Maytag!! For that much money I was expecting the washer to last a long time!

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

2016 model washer. Bought a Maytag in 2016. Replaced in 2020. Problems: Spin cycle extremely noisy, have to close the door to utility room to stay in the house. Leaks a lot during wash cycle. Getting the lock to release takes awhile, sometimes I have to unplug it. Makes a grinding noise at times when starting the spin then.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

We purchased a Maytag dishwasher from Home Depot in January 2009. We did not begin using it until perhaps March of 2009, so just over 2 years ago. It gets ran maybe 1 to 2 times per week. I went to turn it on a day ago and the right side of the control panel, where you press the start button, does not work. When I checked Maytags website, I discovered there was a recall due to the heating element. So, I had the repair technician out and he told me that the control panel was bad and it would cost $300 for parts and labor to repair. We paid $600 for this dishwasher. Of course, we have the option of purchasing a new dishwasher and receive a rebate but that ends up being more than just ordering parts and replacing them ourselves, but something only 2 years old should not break. From reading all the other complaints on this forum, I am surprised that Maytag has not done something about the control panel and the humidity issue which seems to cause the control panel to go out. This is an expensive fix which Maytag needs to address. Come on Maytag!

We have had this dishwasher [Model MDB7749SBW2] for about 1 1/2 years now, and gave had a lot of trouble with it. It will run a cycle on its own without anyone even touching a button. My current problem is the start button wont work. I reset the dishwasher by pushing the series of buttons I found online to do a reset, and the start light lit up, but after the reset cycle was finished I tried to run a wash cycle and couldnt get the start button to do anything. Ive seen a lot of reviews online on this being common with Maytag brand dishwashers this old. I will NEVER buy a Maytag product again nor would I recommend it to anyone as a good product. I am very frustrated and disappointed in Maytag!!!

Bought a Maytag Stainless Steel kitchen stove to upgrade my appliance before retirement. 14 months later the spring loaded hinge failed. A bad piece of engineering in the way of a retainer pin to hold the spring pressure tore out of its pressed metal hole. The hollow pin was fastened in place by a 3 fluted punch instead of with a proper rivet with a head. My local parts supplier had 10 on hand so you know they are aware of this. $70 and an hours labor and it is repaired. My local seller said, Too bad you didnt get the extended warranty. So much for Maytag dependability.

I bought a Maytag Centennial Commercial washer, 3.8 cubic feet, Model # MVWC425BW on September 17, 2014. My clothes were never clean and barely wet. The machine took almost 2 hours to do a load of clothes and they werent even clean! I bought the 3-year extended warranty through Lowe’s. Three years and 8 days later the machine stopped working. Serviceman came out and told me the washer was fatally wounded. He said the transmission failed. He also told me the replacement part would be $400.00 and that it wasnt worth it. He said these machines are junk and Maytag has had all kinds of issues with them. So Maytag knows these machines fail and yet do nothing for their consumers. Maytag, you will only ride on your name for so long; consumers are catching on. Maybe back in my Moms day you were the go-to brand but Im afraid that ship has sailed. Ive always gone with Maytag but now I question that choice. I came on Consumer Affairs page to see what brand I could buy other than Maytag. Seems Kenmore gets high marks.

Started having problems summer 2017. My dishwasher leaked and tank replaced, followed by drain pump, followed by circuit board in 2017. Didn’t have use of it for months. It has started leaking again as of Sept. 17.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

Replaced an old Glenwood gas stove with this Consumer reports top rated Maytag. The boiler doesn’t work as well as we’d like, but after more than 20 years, no major issues. My wife & I both cook, & as with most things, I’m happier with it than she is.

Not only does dryer come with missing parts and are told by Maytag 1 to 2 weeks for delivery or drive 25 miles to pick up one. You do not qualify for rebate even though you do not receive washer and dryer for 5 days after rebate starts. Should have kept my old GE was faster and got clothes cleaner. Was looking at a Maytag refrigerator not anymore with their service.

I purchased my Maytag Bravos XL washing machine in July 2016. In August 2016 it broke for the first time. I was just passed my 30 day moneyback guarantee, so Sears would not take the washer back. I have had more than 10 service calls on this washer in one year. I live in a rural area, so Maytag told me I was in a non-serviceable area and would have to wait WEEKS until they found a repair person willing to come to me. I only live 40 miles from Richmond VA, where I purchased the washing machine, so imagine my shock when they told me they couldnt fix it because of my location! Ive had countless people in and out of my house, and it still does not work right. You can only do very small loads, so the perk of having an XL machine is none. But even at that, it does not properly clean anything, tangles clothes, and will leave even the cleanest items looking terrible when they come out.Ive had a new circuit board, new transmission, new bearings and gears, new balancing rods, and still, Im left with a machine that does not wash and makes terrible grinding noises. I bought the washer and matching dryer as a set, and even the dryer had to get a new circuit board put in it in the 1st 60 days! After thousands of dollars in repairs on a $1000 washer, Maytag will not admit I have a defective machine and replace it! I just ran a load of laundry and have to call Maytag yet again, because the grinding noise gets louder with every run. Do not waste your money!I would give anything to have the 29 year old set I gave away when I bought this garbage back! I have literally been on the phone with Maytag in tears because it doesnt work properly, Ive had to throw away items that would not come clean because there is not a laundromat available in the town I live in. All I want is to be able to keep my family in clean clothing and linens, doesnt seem like too much to ask.

It is not worth the money. I paid $2500.00 for a Maytag refrigerator that I had for two months. Two service calls were made to Maytag as of 07/07/2014, the problem no ice and the refrigerator stays warm. The problem has not been resolve and Maytag refuses to replace the item.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

Purchased our Maytag in October 2009. From the beginning it would make loud, popping noises occasionally but seemed to work just fine. At the time of purchase, we opted to buy the 5 year extended warranty for $125.00 (just in case). Here we are at seven months after that warranty is no longer any good and the freezer leaks all over the floor and we have to keep a towel at the bottom to soak it up.This morning I wake up to the panel being completely out and fridge is not running at all!!! We thought when we purchased our Maytag that we were buying the best of the best... not even close! We just paid for an expensive piece of junk! Who has the extra money just lying around to go buy a new fridge? Not us! This is unacceptable!!! I have read other reviews that sound pretty much exact to our experience with this refrigerator. I hope somehow they can and will be held responsible for putting this product on the market knowing full well it is an over-priced piece of junk.

We purchased Maytag microwave (MMV4205DH1) less than two years ago. Within the first year, the microwave would not work and we would see an Open and Close Door message. We had it repaired and now 10 months later it is doing the same thing. The cost of repairs is high--the same as a new microwave. We have been inconvenienced throughout the holidays by our broken appliance. Disappointed.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Bravos WL purchased in May 2015. Terrible product. Last week stained 2 shirts beyond repair. Maytag service repairmen stated these machines were poor quality and the only settings that somewhat work are Deep Wash and Bedding. They recommended I buy something other than Maytag. I am not making this up - it was unbelievable. I got Maytag on the phone while the service techs were here so they could hear the comments. The supervisor, Kimberly, said I could not get resolution unless the technician declared it a functional failure. I asked for the definition, as I would assume the basic function of a washing machine is to clean clothes. Still working the steps to resolution, but I believe there is evidence for a class action lawsuit.

Bought this washer back in March of 2016. This is the biggest piece of garbage that I ever came across! That washer does not clean clothes, when they are dirty. If I stand in the rain dressed in dirty clothes, they get cleaner than in the washing machine. In 5 month I have tried every possible variation of washing to no avail. I have to handwash the clothes that I wear to work in the garden, or any other dirty job, because the washing machine does not do the job! I bought that washer at ABC warehouse, I paid almost $400 for the thing, and I have to handwash my dirty clothes!!! Shame on you!!!

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

We purchased the Maytag Neptune washer and dryer on May 2005. We purchased it for $2,000. We have had so many problems as we have replaced the drain pump 2 times because of objects getting stuck in it. We have also replaced the door switch, as well as flooding my laundry room floor several times.In 2006, we received a notice of recall. We responded to the recall and were supplied with a GFCI plug for our washer, as this was to prevent the control board from catching on fire. In September 2011, the control panel on the Neptune washer failed. I now have to purchase a new washer, as this is an expensive fix. With this poor workmanship and problems that we have encountered, I am very disappointed. This was a lot of money to spend on a washer, only to last 6 years.

Really havent had any problems. The Maytag repairman really is lonely. Great quality wash machines and dryers for that matter. I havent had to do anything. Spins well... Very quiet, no complaints. Dryer works well too. Many cycles area to put fabric softener and bleach. It has a extra extraction cycle and many other features.

I bought the Bravos glass top washer. It was always loud. I have a friend who had a cheaper model and his was loud too. My washer barely lasted two years before tearing up. It cost $85 to tell me it would be over $500 to fix it. I paid over $600 so it wasn’t worth fixing. Lid lock went out and gear went bad.

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

Our less than five yr old washer finally died. It had been making awful sounds. Started in only very small loads but then started in bigger loads too. It finally stopped altogether. Model number MVWC400XW4. I would NOT recommend this washer.

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

Purchase washer and dryer January 26th, had delivered said February 2nd. Had a horrible delivery service, delivery men were very rude and scratched the dryer. Washer never worked correctly, called and had exchange set up for February 9. Washer was delivered on February 9 and again we had a horrible experience with the delivery drivers. They scratched the washer. The owner of the delivery company came to our home making sure everything was correct. Washer worked well for two and a half weeks. Then I noticed the water was slowing down when it was filling. Then this morning the washer completely stopped filling. We called Maytag and they told us we could not get anybody here until next Saturday. They were rude on the phone. We then called Home Depot where we purchased it and said we want to return the washer and dryer. They said we cannot return it. We are stuck with it. Now weve been arguing with Home Depot and Maytag all morning trying to get someone to my home to get the washer fixed. This set cost $1,400 and Maytag is not supporting us on selling us 2 lemon washing machines. We are stuck because we cant return them or exchange them. Home Depot gave us an option to exchange for a lesser model that they have in stock. When you read the reviews for that model the reviews are terrible. I would highly recommend that you do not purchase a Maytag or Whirlpool product. Their company does not stand behind their products or their workmanship. If I had the opportunity I would return these to the store. But it has been over 30 days and I believe that is not an option. Stuck with a lemon. Very sad that customer service is so crappy on an American-made product.

I bought a new washer and dryer on Sept. 9, 2011. Front Load Commercial 2000 Series. I have had Lowes to my home 2 times since it was delivered because it shimmies across the floor. I am very upset with the purchase of the Maytag front load washer. If you could please get back to me on what can be done. I would like for a representative to contact me and come and look at the situation.