I bought a Maytag Washer Bravos XL approximately 13 months ago. To be exact, July 16th, 2016 through Home Depot. Model #MVW8775DW. Since I bought, the washer shakes, and doesnt complete the cycle as it gets stuck on the spin cycle. I have called Maytag and they have sent out a technician... They have told me that there is nothing they can do. I told Maytag that their product was a lemon and this should not happen... And to please it with one that is not defective. Since then, the cycle does complete, but the clothes are soaking wet and I have to run the cycle again, just on the spin cycle.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

I bought a Maytag Bravo washer with the new stainless tub and the bottom agitator. It also has a clear glass lid. Mistake. I can see the action of the washer thru the glass lid and it definitely doesnt wash the clothes very well. They just stay in the same position and the bottom clothes get agitation but the tops ones just sit there. The towels especially smell musty after they have been washed. Probably because they dont get agitation. The water level is so low that the clothes barely get wet. It was a good idea of the company to save water and electricity. But they must not have thought about getting the clothes clean. If I could I would get rid of this machine but I wouldnt want to subject anyone else to this type of washing machine. I would feel badly selling it knowing that it doesnt get the clothes clean. So I would never suggest getting a Maytag washer with a glass lid because you dont want to see what it is not doing.

Bravos WL purchased in May 2015. Terrible product. Last week stained 2 shirts beyond repair. Maytag service repairmen stated these machines were poor quality and the only settings that somewhat work are Deep Wash and Bedding. They recommended I buy something other than Maytag. I am not making this up - it was unbelievable. I got Maytag on the phone while the service techs were here so they could hear the comments. The supervisor, Kimberly, said I could not get resolution unless the technician declared it a functional failure. I asked for the definition, as I would assume the basic function of a washing machine is to clean clothes. Still working the steps to resolution, but I believe there is evidence for a class action lawsuit.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

I always thought Maytag was the best, maybe because of their ad. Finally, I bought a refrigerator two months ago, which has turned into a nightmare. The company has sent a tech six times and they all say that it is a bad design which makes my vegetable drawer full of water because of moisture. And they refused to do anything about it every time (bad management). They have already spent more money on service than what I paid for the refrigerator. Figure that out.Do not buy Maytag. It was the biggest mistake I made. I also bought a washer and a dryer at the same time. I wish I could send them all back because of the ignorant people they have working for them in their complaint and service office. Anybody out there, if you want to buy an appliance, make sure it is not Maytag.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

I just want everyone to be aware that Maytag went bankrupt several years ago. They were bought out by another company that still puts the little Maytag sticker on, and all the products are made in Mexico. Apparently all the lawsuits wiped out the company. I did not know this when spent several thousand dollars on one of the best Maytag refrigerators a few years ago. I had nothing but problems with it, and literally had to fight with customer service while it was still under warranty. Needless to say, it only lasted 7 years before the compressor went out, which is roughly $1000 to fix. Kenmore here come...

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

We have purchased several washer/dryer sets in the past decade & will never purchase another Maytag. After 3 years of very light use, it stopped working. We had a certified Maytag repairman come & tell us we needed a $600 circuit board replaced. We reluctantly paid for it and 3 months later, intermittent problems began. Plus, it is obnoxiously loud. The repairman said this is normal. Randomly stopping the cycle, not starting the cycle at all without multiple restarts ... the list goes on. The 3 Lg sets we have bought are awesome. Maytag may have been king in the 60s, but the quality of their products has tanked. Dont waste your money on their products.

Our Maytag dryer is only, maybe, 3 years old. I do not dry towels, jeans or heavy sweatshirts in it (I line dry and then soften up in dryer). I clean the lint filter each time. Our heating element has gone for the second time. The first time it cost $200-250 to repair. It is so sad that our appliances are not made to last as they did. Or is it just Maytag? You can be sure we will not buy another Maytag item. I am looking into recalls at this time.

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level not correct, binding laundry together and replaced the same parts with cheap parts over and over... just wanted clean clothes in a no frills washer. NOT with this washer. Owned it 3 yrs and disliked it the first half washed load... $869.00 heap of junk.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

Second time I have purchased a Maytag washer. Both units failed within six months of extended warranty running out. Maytag repairman is sitting on his **, not because they have a quality product but because consumers are seeing that it is a subpar product. Don’t waste your money on them or any of their off brands.

Maytag model mfd2561hes French door stainless steel purchased in June 2005 has been the worst appliance purchase ever. After 1 year warranty expired, icemaker and water dispenser stopped working. Was told by repairman to thaw the tube for water dispensing with a hair dryer. Are you kidding me? Why should I have to pull a huge refrigerator out from wall and put the hair dryer to it to thaw out the water line when I need water? What is the convenience to that? Cant buy fresh vegetables as it will freeze before I can use it. This is the worst appliance ever. Dont buy Maytag products. Maytag doesnt back products like the old days when they would last 20 + years. Cant last even a year anymore. Sad!

My Maytag Series 300 Dishwasher would not start. I read the reviews and took the door off (easy if you have the right tool), removed the control panel box (one screw), and cleaned the ribbon with electronic cleaner as per someones suggestion. It started right up. This is a bad design. Would I buy another Maytag? - No way! We will see how long this lasts. There is no seal on the door to keep out humidity. Do we really need a new control panel? When this is done...I am done with Maytag!

We purchased a Maytag brand thinking it would be a quality long lasting machine. Wrong, the washer shakes from day one, We complained to Lowes, they brought out and installed a second unit, it does the same. The clothes dont get clean, sometimes you can see the blue HE Tide still on the clothes (sheets) after cycle is complete. Junk, waste of money, Ill never buy another Maytag product again. Dont waste your money on a Bravos Maytag top loading HE machine.

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

Recently I purchased a Maytag Bravo Washer and Dryer. These two items are the single worst appliances I have ever purchased. They are loud, ball the clothes into a knot and run forever. I plan to sell them on Craigslist and buy a Speed Queen.

The only reason I am giving 2 stars is because I didnt actually spend my hard earned money buying these machines, they came with our house purchase. At first I was excited to have a good quality washer/dryer... Now I understand why the previous owners left them behind. My complaints are like most of the others on here - takes way too long to do a load because of the stupid water sensor, it doesnt wash loads evenly so everything on top hardly gets wet and washed properly, lint all over our clothes, powder residue left behind even though I set it to 2 rinses, a lot of settings but missing useful ones like quick wash... just all around disappointing. At least one good thing has come out of this and we will not be buying Maytag for our new laundry room. Saying that I have also read so many bad/worrying reviews about Samsung and LG - cant any company make good, reliable, lasting products and stand behind a warranty anymore?!

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

About 6 years ago we purchased a new french door style refrigerator. It lasted one year and one month then needed over $700 in repairs. First you need to know I am into electronics, DeVry graduate with 30+ years experience in repairing electronic devices. The Maytag basically frosted over in the freezer and was warm in the upper part of the fridge. I called a friend who had experience fixing fridges and lo and behold we found something really unusual.The way this machine operates is by blowing the cold air from the freezer up into the fridge. There is a fan located in the back of the freezer wall that does this. We found the fan, which was mounted in a grey box, spinning at about 2 revolutions a minute. My friend took me to the wholesale parts distributor he uses and we gave them the brand (Maytag) model (MFD2561HES) and they gave us a fan... just a fan with two wires. No grey box with fan inside... At this point I got curious, I mean WTF?!?The grey box was made not to be opened and I had to get clever so as to not damage whatever was inside it. After getting it open I discovered the fan inside was wired to a circuit board which upon inspection was a timing circuit. This is why the fan still turned only too slow to function. The new fan was installed and my only problem with the fridge now is the ice maker, which I disconnected.Conclusion: Maytag actually designed this fridge to break down and require hundreds of dollars of repairs AFTER the warranty expired by installing a timing circuit that disables the fan that drives the cool air to the upper part of the fridge to keep your food cold and your freezer frost free. Replace the grey box with a normal fan and youll get years of good use out of your French Door Maytag! As long as you clean the seals regularly and dont mind buying ice to fill the tray with... The repair cost me $39 and a six pack of beer for my friend.

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

Oven failed after 2.5 years of normal use (1-2x / week). Apparently a relay failed (and burned out bake element). Contacted service & parts dept and learned that repair would cost $100 for service visit and $413 to replace the control board. Only the $80 bake element is covered by the limited warranty. Wonderful oven if your hobby is appliance repair. After 2.5 years, it now functions better as a toilet than an oven.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

I am absolutely disgusted with this Maytag Bravos XL washer. Have owned it 6 months and cant wait to get rid of it. We live on a farm and have cattle. If jeans go in the machine with mud on them, they will come out with mud on them. I have tried soak, deep water wash, power wash. Nothing works. I might as well put a wash tub in my back yard and wash by hand. Anything black must be washed by itself as it will come out covered in lint. How did this machine ever go on the market? Expensive mistake. Please do not buy this machine.

I purchased an automatic dishwasher for $660.00 on or about Aug of 2007 (Mod #MDB6759AWS3 ser # NY3417703). It was a model about to be discontinued however still carried the full one year warranty. After install one year and 28 days it failed. The tech described a faulty computer board and a replacement cost of $885.00, a cost of $215.00 more than it originally cost!! They did offer a warranty of one year after we installed the new part but at a cost of $215.00 more than we originally paid! Maytag promotes their brand as reliable. However I dispute this claim.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

My washer is less than 3 years old when I noticed the bleach dispenser has filled with water. I soaked the water out with a towel only to have it fill again the next time I washed. This in addition to the feeling I have that too much soap is left in clothes and spot removal is pretty consistently negligible.

Maytag Bravos Series 300 - I bought this machine less than a year ago. There is an awful smell coming from the machine that I never smelled from any other washer I have owned. The clothes do not look, feel or smell clean, and my towels are ripped. It is an extra large washer, yet when blankets are put in the machine bounces and shifts. After reading all the reviews, it seems I am not alone in my concern with a machine that was not only expensive, but was told it is a great product. Maytag needs to do the right thing and recall this machine.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

A year or so after purchasing our new home, we purchased new appliances. We thought Maytag was a good company to go with. We had serious issues with our 2005 Maytag bottom-drawer freezer refrigerator right off the bat. It arrived with a large dent in the door. They offered to take $50.00 off the price. We insisted on one without a dent. They replaced the refrigerator, and shortly after, the board and the ice-maker went out right away.Although the parts were under warranty, we had to pay for the labor. The refrigerator is 6 years old and now it is making a constant knocking sound. We paid a lot of money for what we thought was a quality appliance. What a joke. We had also bought a new Maytag washer and dryer set and they fell apart after 5 years. It’s the same with the Maytag dishwasher. Do not buy Maytag appliances. They are cheap. They fall apart. The customer service is poor. I feel cheated.

I bought the Maytag Bravos X, last year. The silver color and glass top fooled me into thinking this was better quality than it is. This washer is very easy to go out of balance. I had to open the top (easy) and install/glue a little styrofoam, to limit the amount the tub could travel. Second unresolvable problem is how to wash anything larger than ONE outfit. If you watch the videos, and read the information, this washer is supposed to flip your clothes so whats on top makes it to the bottom for agitation. Ha! Absolutely BS. Unless you wash a very small load single level. The clothes in a TYPICAL size load will sit exactly as you loaded it.the only attention the top layer of clothes is only sprayed with water, no agitation. Hope you dont have kids. Doesnt XL mean extra large? It sure does, you can wash one pair of extra large pants, and or one extra large shirt.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

We have had our washing machine for about 6 months, we got the F3 E6 error code. After doing some research, we found out that the control module was what we needed to replace. My husband and I called both Maytag and Lowe’s, (the store we purchased the washer from). We have been given the runaround. After talking with several managers in the Lowe’s warranty department, we were told that we had to contact Maytag directly about that particular problem. Okay, no big deal. We called and every single time we were put on hold for at least 30 minutes before we were hung up on. Not once did we even get to speak to a person. If we don’t get a response and our problem doesn’t get fixed, I will be going to the Better Business Bureau.

Christmas sale, needed a washer. Had a great experience with Whirlpool Duet so went for the on Sale Maytag Bravo MCT. No agitator which I thought odd. Bought the warranty. Did no good as soon as I hauled the washer home (3-hr trip one way). It wasnt washing my clothes clean. Hubby said try different cycles and soap and temperatures but at 8 months pregnant it wasnt long when I didnt fight with the machine but focused on a very busy life. Baby number 7 and I didnt care how the clothes washed as long as they didnt stink. Well baby is older, the warranty is not over and after much dialoging, no one will do anything for me. I put muddy pants in, they come out muddy. I put cloth diapers in, they come out smelling like pee. How hard can it be to come up with a machine that just turns clothes round and round with a little soap and water? Apparently really hard as Maytag failed to test this machine. Maybe city folk just have lightly soiled but on the farm with 7 kids, my kids play hard and their clothes are very dirty. They continue to stay dirty unless I wash them twice on Power Wash and Extra Heavy Load. Not impressed. Would like a replacement washer of equal or lesser value, anything that works. Oh P.S. I have the receipts and order number. Sorry its not put online to be verified buyer but dont feel like digging for paperwork at the moment.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

The dishwasher doesnt clean and the dishes and silverware come out greasy. What a piece of crap.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

We purchased a new Maytag Bravos washer and dryer. The washing machine senses the weight of the clothing and determines how much water to use. The machine does not put enough water in to completely immerse the clothes, therefore after the load has washed, the clothes come out of the washing machine partially dry. I have to wash the clothes a second time therefore using detergent twice, water twice, electricity twice and my time twice to wash each load. After a while the machine stopped washing altogether. I would load the laundry, add the soap, close the machine and start the machine. It would begin to put water on the clothes and sense the weight of the clothing and it would get stuck there. I would hear a buzzing sound and the clothes have been stuck on this same cycle for over 15 minutes and it would not wash the clothes. I tried starting the machine again, and it would drain the machine. Id have to add more soap, use more water, use more electricity and use my time again to try and wash the same load. They sent out a repair company who looked at the machine, did whatever they did (and left a bunch of water on the floor behind the dryer and didnt have the decency to tell me so that I could clean it up). They said they had to order parts and they would come back. They called me several hours later and said they had the parts in their warehouse and they could repair the machine.After a while, they said they were finished and that the machine was repaired. I tried to wash a load after they left and... the original issues were still there. I called the repair company and told them what happened. I typically do laundry once a week, so out of fairness to the technicians, I told the lady that I didnt have any more dirty laundry and that I wanted to try the machine again when I had dirty laundry the next week. I called the next week and Maytag said that I had to pay for the technicians to come out, even though they never repaired the washing machine.After complaints they offered me a $75 credit towards the repair company which I refused to accept. Then they told me I could buy another Maytag machine and they would give me a discount. So basically, I would get something like $76 off of a $600 machine. Really? And then the idiot had the nerve to tell me that it was customary for the clothes to come out partially dry. So in other words, he was telling me that these machines were designed with flaws to partially wash clothes so that consumers would have dirty clothes. I asked for a replacement machine of equal value and they told me that Maytag does NOT replace machines. They sell this crap, knowing that it is no good and they arent willing to replace it! I got someone else on the phone and he said that I will not have to pay for the technicians coming out a second time to attempt to fix the machine. I AM NOT A HAPPY CAMPER.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

I made the mistake of buying a Maytag fridge and dishwasher when I moved into my home 16 years ago. Ive had nothing but trouble with these inferior appliances since almost day one. The seals on the freezer quickly started to separate, causing ice chunks and insufficient temperatures. We had an extended warranty, but they refused to replace it. Weve had that fixed approximately 10 times - never resolved it. The plastic covering on the dishwasher racks began to peel early on, which caused the metal underneath to rust, in turn causing the clean dishes to come out with little rust flakes all over them. This company obviously cares only about profits. Save yourself a ton of headache and DO NOT BUY MAYTAG.

I, too, am having major problems with my Maytag Neptune washer, much like many of the writers are. I am extremely disappointed in the Maytag corporation for putting out such an inferior product that it wont stand by. I wonder if a new class action suit could be filed.

2011 model MVWC2oox W1- spin dry failure - We purchased above top loader in 2011 and have had no issues until now. Currently constant failures on spinning and drying. Spin cycle stops without getting up to speed and appears to be an unbalanced load sensor problem. Also draining is not completed (possible pump going bad). Area tech came out within a week as promise and ran the diagnostics and found no faults. Problem has continued. We do a load a week. Looking for better answers or a new washer.

I purchased the Maytag Bravo Series in August 2010. Two weeks ago, I had to replace the idler pulley on the dryer which was no easy task. Now today I was washing a load of clothes only to walk into my utility room and find it flooded. This didnt even start out as a small leak so at least you would have a warning. On the spin cycle, the washer is making a clanging sound. These were not cheap models. I paid $1600 for the set. I will never buy another Maytag product especially after reading all the complaints that people have had about this series. Why hasnt something been done to protect the consumer? I did not purchase the extended warranty as I thought Maytag sold a good product. I owned another set of Maytags that were almost 30 years old when we got rid of them and did minimal repairs over the years. We are only a household of 3. It is not like these appliances are overloaded or abused. Its very disheartening. In this economy, most dont have money to just throw away and that is what I feel like I did!

In May 2007, I bought a matching Maytag Neptune washer Model MAH5500 and dryer. I also bought the 3-year extended warranty. Approximately 4 years later, actually 1 month after the warranty had expired, the washer started to get very loud and sounded like a jet engine taking off. I called Brennen Repair Service in Midland, Michigan. The repair man came out and said he did not even have to look at the washer. He knew what was wrong. The bearings were going in the machine. He said I could fix it for approximately $600 or just run it till it quits. I was furious. I called Maytag and explained my issue and was told that there was not a recall and they could do nothing to help me. They even told me that they had not had any complaints of this nature regarding this model. I told them they were full of it. I know of at least 4 people in my family and workplace that have had to replace the Maytag front loader piece of ** washing machine. I think Maytag should stick behind their product with all the complaints out there. I would like to shove my washer through their front window. I previously owned a Maytag washer for 25 years and had not one issue. It ran perfectly. I will never buy another Maytag product nor will anyone in my family. Maytag, you suck. Your service and reputation is appalling.

I bought a brand-new dryer Maytag Bravos. It broke after 3 weeks. They came to fix. A few months later, same thing happened, but I have 6 people in my house. They told me someone would be here the next day, and then that person canceled. They called someone else. He came and said I have to wait 3 days for parts. I called at least 6x and waited 30 minutes each time. They kept telling me theyd call back, and theres absolutely no call back. Then I called corporate Yvette, who was totally cocky and rude (866 817 5404). She said she would try to get back to me another day because she had meetings! Then, I was irate. I mean how rude. So she called me back and said, I ordered you the parts. Now you call Dan Marc, the service company, and make the appointment. Is this woman kidding? Then she went on about how Maytag has a 13% rating (They are Maytag.) and how their product is so wonderful. Now this woman is competent cocky and rude, and shes the presidents secretary! So whatever I call Dan Marc, they have no appointments Tom and wont make me an appointment. This is how a new product should work? I asked her what I do when it breaks again and again and the warranty is up. She told me they dont work on what ifs and if that time comes, it will be her decision. I am disgusted and have a house full of kids with no dryer? And I have given them another chance after that Neptune disaster. Im appalled and dont even know what to do.

I bought a Maytag washer (Centennial) because of its reputation. I didnt even realize this site was out here and would have made another selection had I known. I bought the washer on June 7th of 2011. On June 15, 2012, the washer just quit working. I called Maytag. They said since the warranty was over that I had to pay a technician to come out and it would cost $129. I was upset but I had to have a washer so I scheduled it. The tech came out and said the motherboard was bad. He said that this has been a common problem with this machine and that Maytag should actually recall the part. The replacement part was much better. He suggested I call and complain. The part was $180. He said that Maytag may reimburse me because it was so close to the warranty cut off. I called Maytag to explain the situation, and what do you think their response was? Since you already paid for it, there isnt anything we can do. Nice! What a joke. I will never buy another product from them and neither should anyone else.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

My dishes come out super clean and I love it, even when there is calcium build-up around the filter. Thanks to Maytag and their great technology. You cant beat Maytag.

My stainless steel french door refrigerator started to rust 4-5 months after purchase. Upon contacting Maytag/Whirlpool I was advised that this is cosmetic and the cosmetic portion of my warranty is expired. I think this is a poor grade of stainless steel and should be recalled and/or replaced. I would not recommend.

My Neptune has been a great washing machine. I did have to change the door gasket twice and just recently changed the bearings. My machine sounded like a jet engine. I ordered the parts on eBay, watched a YouTube video, and fixed my Neptune washing machine. Its still working and runs quietly.

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.

For years I wanted a top loading Maytag washer. Last year I bought one at the cost of £720 plus VAT. Started using it last July and in November this year it broke down. The company I bought it from said, Sorry, youre out of our warranty... Really! Here’s some people who might fix it. Eventually Hotpoint took it on and honored a two year warranty. Since November I’ve had an engineer out twice. Still isn’t working. Won’t replace it because it’s now discontinued, so more parts ordered. Engineer advised me to go buy another washer. Thanks Maytag for totally disappointing me in what I thought would be my perfect washer. I will continue to email etc and hope that someone will help me. No point in phoning because no one listens. MY OPINION - DONT BUY AMERICAN PRODUCTS IN THE UK AS NO ONE CAN REPAIR THEM PROMPTLY IF AT ALL.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

My disappointment with this washer (Bravos xl) is that it smells moldy and musty no matter what I do. I clean with affresh when light comes on, leave the top open, etc. I have tried cleaning it with baking soda and vinegar poured down the detergent opening. Water does not drain from the bleach or softener openings. I have resorted to using baking soda in every single wash and adding an extra rinse to keep my clothes from smelling. The laundry room always smells. I would go back to an agitator in a heart beat if this hadnt been so expensive. DO NOT BUY THIS MACHINE.

The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

I would like to start with, my Mother had always used Maytag washer and dryers. Her machines would last 20 years or more. I bought a Maytag front loader washer and dryer in 2006, since owning these machines have spent in upwards of $1400 in repairs. Some being flood out of tub, mother board blow out a couple of times as well as various other issues. The biggest problem is the awful smell of our clothes, I must wash clothes multiple times to try and remove these smells. I tried contacting Maytag and they dont want to hear my complaints and push me off to purchasing another washer and dryer. Oh, I will be buying a new washer and dryer it just will not be Maytag. Do yourselves a favor and DO NOT buy another Maytag. This is not the same company my Mother knew and trusted.

We got our Maytag fridge approx.18 months ago. There was no trouble the first year and there has been nothing but trouble for the last five months. The freezer started frosting one day which causes temp to get in danger zone - we defrost it with a hair dryer about every week and it has continued to frost up ever since. We have a friend that works for a certified Maytag repair business. He came to our rescue five times and called Maytag hot line for help.Together, they could only suggest that the gasket be replaced. He could not see anything wrong with it but we changed it just in case. Still, the problem continues. When we called Maytag customer service (877-556-57420), we were told that no one has had the problem before us. We just looked online; there are 521 complaints about Maytag. My question now is, how do we get a class action lawsuit going?

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

Maytag Model # MMV4205DS - First Maytag microwave lasted just over a year before it quit. Replaced with same model to avoid install hassle and 1 year and 4 months later got the dreaded open and close door message. Read so many horror stories about repair service for Maytag that I decided not to bother and purchased a GE. I will never ever, ever buy anything Maytag ever again...

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

This is the worst washing machine I have ever had in my life. Machine started bouncing during the wash cycle and also the spin stopped. Never in my life have I had a machine fail on me like this one. I spent a lot of money on this. This machine should be recalled. I read up on all the complaints. Its a model #Tw6600TQ0.

Like so many other people reviewing Maytag refrigerators with bottom freezers, I am dealing with water on the floor. At 64+, I am not eager to tackle the problem as a DIY project. Once of defrosting and cleaning up was enough. I love the looks of my 2 yr old $2000 4 door fridge/freezer but hate the issues. I guess Maytag is going to ignore all of us. When someone finds a reliable company, sing it from the rooftops.

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

We bought a Maytag refrigerator serial # K11101146 and model # MBL2258XES1 on 5/7/2011. We started seeing puddles on the floor about a month ago coming from the bottom freezer. The warranty on the refrigerator was only good for a year. We investigated it further online and saw that a lot of other people were having the same problem. We found a video on Youtube on the solution, which was to tear the bottom frig apart (which is a pain and takes about 3 hours to complete) and to thaw out all the ice accumulated on the coils and run hot water down the drain until that thaws out. It makes a real mess. Now we see that this will probably have to be done again and again from others online who are having the same problem. We never had this problem with any of our refrigerators or any problem with them for that matter. Our last one was a 15-year old Amana and we wanted a more energy efficient refrigerator. We bought this one at Home Depot thinking that this one would last us for the rest of our lives. We are in our mid 60s now. This should not be happening at all especially as much as we paid for the refrigerator. I contacted Maytag and they more or less said, “Sorry about your luck.” I hope something can be done about this, especially for the amount of complaints filed. Unfortunately I did not take pictures but if it happens again, which I understand from other complaints that it will. Thank you.

WORST MACHINE EVER! Besides the soap scum Maytag Bravos XL Washer leaves on all of our jeans and my husbands work pants, the machine decides when it wants to work and when it does not want to work. Weve had repairmen over, we have called the 800 numbers, just like all of the other reviews on here. Ive readjusted clothes in that thing more than Ive done laundry in my life!!! I HATE this machine. Ive memorized the manual from reading it so many times, have the correct detergents, tried washing large loads, small loads, lined up the clothes around the outside so the middle thingie is not covered, thrown clothes loosely in there. Every way possible. The machine senses, starts filling, then just stops. Today, no matter what I do with the load in there, it will NOT run, it keeps shutting itself down and I do not even know what else to do. NEVER EVER EVER buy this machine! We will never own another Maytag EVER.

First off, the drum split apart on the dryer. The drum part was not in this country, so instead of going ahead and replacing the clothes dryer, they told me to hang the clothes outside for six weeks or whenever the part comes in. That was three months after owning the piece of junk. I was having a bad day already, so I basically completely lost it. Im surprised I didnt get arrested for that. I wont ever lose my temper like that again. The clothes always smell bad, and sometimes really bad. Now, I find out that both washer and dryer could cause a fire. They are sending us a couple of really cheap GFCIs to keep them from a liability issue. Maytag is the absolute worst!

Lid lock issue. 2 years old. I will never buy a Maytag, or any other Whirlpool brand for that matter. I am VERY disappointed. A service call will cost at least $200 dollars so why not just buy a new washer for that price. Also, I read that consumers should stay away from automatic water level washers. They never work right.

It looks big, but is small inside. Its hard to put in several large items. The water filter broke and too expensive to fix. I like the double doors and ice maker. I dont like the freezer drawer. It wont stay open to clean.

After the waranty ran out, oven failed to ignite. Called repairman who couldnt diagnose problem. Broiler works. Replaced some kind of wire & part for $350. Good for 6 months. Happening again. Paid a lot for this oven.

Almost two years after purchasing the Maytag Bravo XL, I am fed up. I have the exact same problems as everyone else in these reviews. Soap scum left on dark clothes since day 1. I thought maybe I was doing something wrong. I have read and re-read the manual especially the troubleshooting guide and still have the same thing happen. Its very frustrating. I constantly have to re-rinse clothes because of soap, lint, dirt, etc left on clothes. I wouldnt give away this washer to anyone, I would rather burn it. I am currently looking for a new washer, the last one I had for 11 years was a front loading Whirlpool. I should have stuck with a Whirlpool, I still have the matching dryer no problems at all.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

Ive had this Maytag microwave for about 4 years and the magnetron had to be replaced. The keypad was replaced three times due to SE code shutting down unit which happened again. When I explained this to Maytag, they said it is out of warranty. I explained to them that the last keypad which was replaced was only 6 months old. They replied but the unit is out of warranty! I would never recommend Maytag or any affiliated companies to anyone.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

Maytag Centennial Washer - Bought washer because of brand name and was that a mistake! This is the Loudest, noisiest, banging clanking washing machine I have ever heard. Every time I do a load of laundry the washer moves a foot from the wall and I have to continually move it back. Needless to say I hover over it all the time when I do laundry. It isnt even 2 years old and we are going to go buy a new machine, AFTER looking at reviews!!!

Maytag 18.5 cu ft Bottom Freezer Refrigerator purchased 12/10/12. 1/12/16 the bottom of the freezer had an inch of ice that leaked onto the floor. My plumber chipped away ice and unclogged drains $97.50. 4/19/18) the same $97.50. 5/22/18 an appliance repair business installed a drain kit $148.40. This was his 25th Maytag with the same problem. A whole website has complaints about this problem. I sent a letter to Maytag and they wanted to send out their technician to find out the problem (with a service cost to me). With all these complaints, and a kit to fix it, they already know the problem but refuse to do anything about it. Maytag used to be a reputable company. No more. The customer service said I should have bought an extended warranty. I said a $1400 refrigerator should last longer than 3 years (the first leaking occurrence). I will never buy a Maytag product (nor Whirlpool that makes it).

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

This product was purchased in March. In September, the agitator broke off. Thats a new one on me with a washer. Every other one Ive bought tended to last 10 years or so, then something like a motor wore out. It was an obvious design flaw on a topheavy agitator held on by a flimsy plastic sleeve. To make matters worse, their warranty service seems mostly geared to selling extended warranties, necessitated by the poor quality and bad design of their products. So, for a mere $182, I can have it covered for the next six or seven times the agitator breaks. No thanks, Ill figure out how to fix it myself when its no longer under warranty, or just cut my losses by buying another machine, and never another Maytag or Whirlpool product. I had a similar experience with a Whirlpool refrigerator purchased in April 2017, which had a defective module that went fortunately just before it was out of warranty.

Just when you think that youre able to do laundry. First, comes the musty smell. So, you clean cycle your HE machine using only the cleaning product directed by the manufacturer. Then, comes the pump being stuck on. Like it still have to drain yet your clothes are soaked but you heard full force of a good drain. Poof. Unplug and kick it. Look on YouTube and discover you should take it apart and clean out some obscure puddle holder & look! You discovered where the sock monster lives...its gross. Going to start my own business (125.00) to clean these things out. Hopefully not get some kind of fungus from the grossest mold ever. Its Maytag not a Home Depot issue.

SO SO disappointed. I thought by purchasing a Maytag washer and dryer that I was purchasing quality products. Not so. After only 3 yrs, the dryer is broken. It needs a new heating element assembly at $139 plus a visit from the technician and installation. In total, it will cost about $300 to repair. The washer is slowly going also. It takes about 2 minutes before it starts. Never used to do that. The technician told me that these do not last and that the computer is likely to go in another couple of years which will cost $400 to repair. I called Maytag to see what they could do for me. They offered the part at 1/2 price but insisted on another diagnosis even though Ive already had one. That along with their labor cost was going to cost more than anyone else. So no more Maytag products for me.

Faulty Maytag Bravos electronic dryer model MEDB400VQ0 - I purchased a new Maytag Bravos washer and dryer in Feb 2011. About 3 weeks ago, I noticed the dryer not drying my clothes. They were hot, but not dry, leaving them hot and steamy. There was also wet lint that kept accumulating inside of the dryer. I took the back off of the dryer to see if there was an obvious problem and I found the blower belt and large bolt that holds one end of the belt to be off and laying on the bottom of the dryer. I have also looked online and did a search on this make and model and the issue I was having, it brought numerous people having the same problem on multiple internet forum sites. Apparently, there is also a service bulletin on this exact issue, but according to the Maytag customer service department, no recall. Therefore, I am out of luck as far as getting any kind of repair (unless I pay for it) because I am out of warranty by 3 weeks. I purchased the Maytag brand thinking this was going to be the best and will last me a very long time. Unfortunately, I was wrong. It only lasted me one year without breaking down and the customer service department is horrible. You can tell they definitely dont stand by their name, the Maytag name is a thing of the past. I will never recommend this brand to anyone else for purchase and I regret having swayed my mother to purchase the very same set I did. This has been an awful experience and I am wishing I had chosen a different brand. Maytag leaves me angry and very much dissatisfied.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

I seem to be just another unhappy Maytag microwave oven customer. The SE code indicates a bad/faulty/short in the keypad. It seems this is a very common issue so buyers beware! If I dont get this resolved, I will no longer buy Maytag/Whirlpool products.