We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

The Maytag Commercial Technology wash machine, the one with the clear top, leaves soap residue on our clothes. We have tried different detergents, always high efficiency, using the extra rinse, using the deep fill and nothing works. We have tried cleaning with vinegar and using the clean washer cycle. We had 2 technicians look at it, one tore the machine apart, both said nothing is wrong with the machine. So, we are left to believe that we are stuck with a machine the leaves soap residue on our clothes as Maytag will do nothing for us because of the assessments of the technicians.

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

Paid $900 for this side by side stainless steel model 15 years ago. Pros: performance, appearance, simplicity. Cons: none. Only 1 minor repair, and the repairman said this is 1 of only 2 makes he recommends.

The cost was right for the quality of the product. Brand was also a factor. We have had no problems either machine, both work as expected and have fully met our expectations. We recommend these products. Energy efficiency, ease of use and capacity were all considerations in making the selection we made. Maytag continues to hold a good reputation. Regular repairs, low quality construction and a cheap finish which looks tacky and is also difficult to clean would each be deal breakers. We purchased our full-sized, side by side Maytag Neptune Washer and Dryer gently used from a private party who needed to obtain different models due to a remodel of their laundry/utility room. We paid about $600 for the pair.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

The washing machine is rusting and Maytag refuses to take care of their inferior product and obvious inferior materials used, and also inferior workmanship.

I purchased the Maytag MDB8959SBS dishwasher back in 2014. I have historically been a Bosch guy when it comes to dishwashers but I have been so happy with my Maytag Maxima washer and dryer, I wanted to give their dishwasher a chance. Well, it has been a major disappointment, to say the least. For starters, it just doesnt clean that well. I am very careful in how I load a dishwasher. I do not put baking sheets across the bottom rack lol. Consistently we find dirty dishes. Then after about a 6 months, I noticed the paint on the adjacent cabinets were peeling in spots (near the top and bottom corners). I started feeling around the outside of the door during the wash cycle and there was a fair amount of moisture collecting around the outside of the dishwasher seal (or non-seal). Fast forward to about a month ago, I noticed a burning smell in the kitchen while it was running. Did the typical check the heating element routine thinking something fell down and was burning. However, it was perfectly clean. Emptied it completely and ran a totally empty load. The smell was still there. I eventually figured out the smell was emanating from the upper right corner of the door. Coincidentally this was right above the location of the control board. I grabbed a tool and carefully removed the front panel and discovered wires were melted (some fused together) and even the inside of the panel (which is plastic) was melted in spots as well.So yes, I could have contacted Maytag and sent pictures and fought with them over a repair but to be honest, I have no interest in keeping this appliance. It has been trouble since day one. Again, to be fair, I have had good luck with their other appliances but this was an awful experience and a total waste of money. I have since gone back to Bosch and could not be happier.

I purchased my machine on June 2, 2021 and it was delivered and installed on June 4. I have successfully done two loads of laundry. On June 9, I attempted washing two small bath mats and 2 dish towels. When I returned to the laundry room to place the load in my dryer, I found the the items in soapy water. I tried many times to reset the load with no success. On June 10th I called Maytag’s customer service and spoke with an associate who walked me through a couple of common quick fixes. These also were unsuccessful. She referred me to warranty service. I will not be able to have my machine repaired until June 23rd! Obviously, if their repair department is so overwhelmed, the products they sell are a piece of junk. I am furious with both the product and the service I have received.

Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We have had several repair calls. From reading complaints from others, I have the same: clothes balloon, clothes rip, dark clothes have a scum on them, even a blanket goes off balance and it is hard to start the cycle. It goes off balance all the time, makes a squeaky sound when agitating and the housekeeper can never figure out what cycle to run the clothes on because they always go off balance, there is a loud vibration, etc. The last repair call was for an actual leak on the floor! The appliance company charged us $95 for the service call, did nothing, and told us the parts would be more expensive than a new washing machine. Went to Home Depot today and purchased an LG washer and dryer for over $1500. I am not even going to try to recoup anything from Maytag because this is the second Maytag that I have had a bad experience with and didnt learn a lesson in the first place. Junk. :(

We have had our oven for seven years this past October 2015 and has now been down for three weeks. Last February 2015 (8 months ago) we had to replace the bake igniter because the oven would not get up to temperature. The most recent incident happened a few days after Thanksgiving (2015), I was cooking dinner and noticed that the oven was not reaching desired temperature. I then opened the door to see if it was hot inside the oven and when I did it must have ignited making a huge poof and flames came out at me! Thank God my 12-year-old daughter had walked away from cooking with me to answer the telephone because the flames came out exactly where she had been standing!!!I contacted Maytag and explained what had happened and how we could have had an explosion or someone couldve burned. The first questions they did ask me was if anyone was injured or any damage to our house?!?! I was happy for that however, it also told me that this has happened before! They called the Maytag repairman in my area and supposedly made it a priority call in which he could not come until 12/10 which was two weeks after this happened. Therefore, my husband and I contacted a different appliance man who came out and told us it was the temperature sensor. Since fixing it, the oven works ok and cooks properly however, when initially lighting/igniting it is extremely loud and makes a very large/huge poof! Its as if the oven is filling up with gas and eventually lighting! The other night when I lit it to show my husband it was so loud that it rattled the door and he immediately turned off the gas to it. I googled this and it said that its basically a mini explosion where the oven is filling with gas and then igniting! Its to the point that we could lose everything we have worked for just to make a meal! We spend over a thousand dollars on our beautiful stainless steel convect oven. Its gorgeous and when working works great however, Im petrified to use it now because Im scared to being burned or exploding! Now we start over and yesterday on Sunday I contacted the original Maytag repairman who said to call back Maytag again and hell come immediately. Maytag originally told me on the phone that they would cover labor and the service call however, ironically enough they did not write that in the dispatch order! Im outraged! What will it take before its safe for our family and home! My husband is ready to junk it and buy a GE however, we do not have the money especially before Christmas to do so. Oh and let me add that the first week we had the oven we had to call them for the window seal to be replaced because it was hanging. So now seven years after owning it and 10 months apart we are having major issues. What happens if its fixed and a year later it happens again? It could explode in our home!!! SCARED & IRATE WITH MAYTAG & WHIRLPOOL.

Maytag Commercial # MVWB765FW0: My husband and I wanted to get rid of our GE front load. It was horrible. Even constant cleaning and leaving the door open all the time, our clothes still smelled like mildew and musty. My hubby wanted an LG and I said no way. As a little girl my mom had an old wringer washer and her first electric washer was a Maytag in the late 50s. She passed away in 2001 and in her lifetime she had 2 electric washing machines both were Maytags. They were so dependable and built to last so naturally I wanted a Maytag. Wrong! I am so disappointed. We purchased it in Sept of 2017 for $695. I was so excited the first time we used it. It was a little noisy, but living in the county and having a well we were glad it was an energy/water saver. The first couple of months it was so refreshing to have clothes that did not smell musty and mildewy. I noticed they were really wrinkled but I still iron anyway so it was not a big deal. However ironing over and over again on some items did not get rid of the wrinkles and the past 2 months I have been going thru lint rollers like crazy and it still does not come off. I have to use a slightly damp lint brush or go over the clothing with packing tape to get the lint off. It is horrible! I dont want my GE back but I dont want this one either! I wish I would have read reviews first and listened to my hubby. I wont ever have another Maytag and when this one goes I will certainly read reviews and go with something more dependable. Unfortunately for now we have wasted the money and it is ruining our clothes! I agree that we should all do the class action. There are just too many of us experiencing the same issues. Maytag should do right by the consumer! We have learned our lesson, review before you buy!

Maytag Bravos XL - I am having the same problem as everyone else with this washer. My clothes do not get clean and they smell. Maytag advertises tumbling, rubbing action to get clothes clean but my washer does neither. The clothes lay in the bottom of the tub and never move except when in the spin cycle. I am going to file a complaint with Maytag and if they do not refund my money am going to file a DTPA claim against them for false, misleading and deceptive advertisement. They will have to pay up to three (3) times the purchase price of the washer. Maybe everyone else should consider the same.

In May of 2009, my husband and I bought a new Maytag refrigerator side-by-side, model MSD-2572VEW. The day we bought it, pieces started breaking. The shelves started cracking, and now they are completely falling apart. There are also cracks in the inside walls of the refrigerator. Every single door shelf, inside shelf and wall is falling apart. I have fixed the ice-maker myself several times. I am now going to design and build some new shelves so that we can get as much use out if it as possible before it is unusable. I am angry that a company can make such a horrible product and not have to take responsibility. If my employer ever provided a client anything but the best, we would all be out a job.

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

I purchased a Neptune front-load washer in November 2005. Now that its out of warranty, theres nothing that Whirlpool can do for me. The front panel of the washer that surrounds the door has been rattling for a few weeks, so my husband took it off and found a crack on the top right section of the panel where its bolted to the frame. There is a rust bubble where the crack started. We couldnt see any of this until he took it apart. The cost of a new front panel is $185 and the response from Whirlpool? They are “very sorry” that this has happened, but there is nothing that they can do. Oh, really? Well, I come from a long line of Maytag owners and there is something I can do: spread the word about the disgusting piece of junk I paid $1,100 for! This washer wasnt even made here - it was made in Korea and its not worth $100! Note to Whirlpool: your customer service sucks!

Refrigerator (Model Mff2558vems) purchased end of November 2011. Early in 2013 notice refrigerator first forming ice all over freezer, including an ice sheet on bottom of freezer. Then noticed water around refrigerator. Called maytag and they sent repairman even though a little over year and out of warranty. Their service people seemed to know exactly what was causing the leak as they came in with the correct replacement part. Worked fine however, there was damage to my newly refinished hardwood floors which Maytag did pay to repair. A couple of days ago I opened the freezer and again noticed ice all over freezer. The next day, water all around freezer. I cleaned everything up, so I thought. The day after, we noticed the hardwood in kitchen buckling up far from refrigerator and the laminate in dining room bubbling, even though there was no visible sign of water. Called Maytag repair company but they couldnt come out for a couple of days. Called another local repair service familiar with Maytag refrigerators and he couldnt find anything wrong with refrigerator even though he knows leaking caused by refrigerator. Called insurance co. and they sent over service master. Leak is definitely coming from refrigerator. They had to pull up hardwood floor, part of walls, the dining room. They now have five large fans going and a defroster to dry things up. This is upsetting, as my daughters wedding is next month, my husband is currently laid off and I dont need this kind of aggravation again. I love the french door idea, so roomy for my large family, but I am now afraid of this refrigerator. I dont want it but think it is ridiculous I have to shell out more money when the refrigerator is less than 3 years old. I talked with a higher level supervisor at Maytag and they are only willing to give a 100.00 rebate towards a new refrigerator since the refrigerator is out of warranty. This is ridiculous. I thought by buying American I was helping our economy but what I got in return is heartache and crappy merchandise. If there is a lawsuit in California against Maytag about these refrigerators I want to join. My friend in N. CA who bought her Maytag refrigerator the same time I did is also experiencing leaking. So frustrating.

We bought a Maytag Dishwasher Model # MDB4709AWW4 about 2 years ago. Complete piece of junk. Just spent $350 on a new control panel. We called Maytag and they told us that our model wasnt under the recall for this issue. The old belief about the Maytag repairman not being busy is a lie. Avoid their products. They are poor quality.

The washer gets mildew all the time no matter how much I use the tablets and yes keep door open. It still has so much. I scrub it and it keeps growing. Sometimes my clothes come out ripped also which is another frustration. Please help these two issues.

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

Perfect for me. It would be better if I had a space to put it without adjacent walls. Mine sits with the refrigerator door against a wall and I have to pull it out to the door space to open it wide enough to pull out the drawers to take them out for cleaning. Otherwise, it has worked very well for me by myself, for me and my husband when he was alive and for my son and his family and myself, and he has 5 children.

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

Bought Maytag dishwasher model number MDB894995BB3 serial # F41103073. About 2 months out of warranty the control panel went bad. Contacted Maytag. After quite some time they agreed to pay for parts. After some more conversation they also agreed to pay service and labor. This was on the first day of August and Maytag scheduled a repairman for the sixth of August. When he arrived spent five minutes and said he had to order parts. The control panel I had already told them was bad. Now here I sit waiting for part to arrive. No more Maytag or Whirlpool for me.

I bought a Maytag Centennial HD washer and dryer. I have had no issues with the dryer but the washer is absolutely junk. I’ve had it 5 months and this is the second time it’s stopped spinning and I’m dipping my wet clothes out. Not only does it cost hundreds to fix it, it doesn’t wash well AT ALL. Your clothes still come out with deodorant stains and spots. It’s a complete waste of money and time. Run as fast and as far away from this worthless machine as possible.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

We purchased a front loading Maytag washer in January of 2011. We purchased an extended service plan in January of this year. I noticed a very loud noise and inappropriate operation during the spin cycle. I called the service plan, who contacted a repair service to come out and check my machine. I was told that there was a major problem that would be very expensive to fix and that the Assurant company would contact me in a few days. The company called and said that they would give me 75% of the value of the machine ($650) because fixing it was not economically feasible. I said that I did not want the money; I wanted the repair that I was guaranteed by my service contract. They referred me to the small print on the back of the sales letter. When I asked about any manufacturers warranty from Maytag (the washer was less than 2 years old), I was told that they had nothing to do with the manufacturer and I had to take that up with them. When I tried to call Maytag, they were decidedly unhelpful and referred me back to Assurant.There are several issues related to this event that I wish to complain about: 1) How dare a major company sell a thousand-dollar appliance that becomes unrepairable in less than 2 years and take no responsibility for the breakdown? There was obviously a defect in the machine that took over a year to show up (we are a household of 2 adults and did not overuse the machine). 2) How could a service contract issued under the Maytag name not be aware of parts covered by the manufacturer? 3) Should not the buyer of a service contract bearing the Maytag name be informed that it is not Maytag (the manufacturer) that is guaranteeing the product, but a third party?4) Should not the seller of a service contract be required to display the terms of the contract in a prominent place? The sales letter specifically states Repair or replace - If we cant repair your appliance due to a mechanical or or electrical breakdown, well replace it. The limits of coverage are in fact given in small print at the back of the letter and are on the contract, but this contradicts what is displayed prominently on the promotion letter. This is false advertising and should not be tolerated.

Would need 3rd panel for 8-year dishwasher - Either no lights come on the panel or Load done lights, like now. It has happened so many times over the years from about a year after spending a lot of money on a Quality unit. Many times I was able to operate it after turning the breaker off/on or leaving it to sit for a week or so, multiple times! Also, the rubber on the racks did not do so great - peeled and rusty. I did apply rubber repair multiple times, then got new racks at my expense. Several other brands bought over the years lasted 10+ years with no repairs!

I purchased a 2011 Bravos top loader washer machine. Doing a minimal amount of laundry for 2 persons, the Bravos is in disrepair needing bearings and an inner and outer tub. I was told to purchase a prepaid service call for $350 that will cover repairs plus a mere 1 year additional warranty. The washer sounds like a jet plane, gives off fouls odors, has black tar like residue after each wash and clothes never smell clean. Maytag has no complaint process, except an online chat that tells you to buy the prepay. Maytag has dumped a lemon on consumers and arrogantly expects us to pay for their garbage. They are disrespectful, dishonest and greedy and dont deserve anyones hard earned money for their ill made products.

Bought in July 2015, brand new from Lowe’s or Sears. When working to its full potential it never cleaned clothing very well, had no designated spot for detergent or softener, just bleach. Just last 3 years and it’s a piece of crap that has to be replaced. Going to argue with the company to tomorrow to get them to replace the broken transmission which may or may not be considered part of the drive motor - all **. This is a very expensive machine that didn’t last a month beyond 3 years! The 10 year warranty covers the 2 most rugged parts of any washer... the agitator never truly cleaned my clothes and now it is fused to the wash basket and cannot even be replaced without being chiseled off. Worst machine, purchase, and brand ever???

I purchased Maytag Quiet Series 300 Dishwasher in 2006. About 3 years ago, I got a letter that a recall had been issued due to an electrical problem. A service repair person came out and replaced the electrical element in question. Next the dishwasher did not work and a repair had to return again. Today I have the same electrical problem and after waiting on line 12 minutes to talk to Maytags customer service, I was told it could cost me a couple of hundred dollars to repair my 7-year old dishwasher. In my last home, my Kitchenaid dishwasher lasted 20 years before needing to be replaced. My daughters Maytag dishwasher lasted on 12 years. What ever happened to Maytags lonely repairman? I now have to get a new dishwasher and worry about my $3000.00 kitchen floor getting damaged with the removal of old and install of new. Believe me, my new one will not be Maytag.

My husband bought me a brand new Bravo Maytag washer and dryer from Home Depot in November 2010. In May of 2011, we moved and the dryer hookup was electric instead of gas. My husband knew how much I love the dryer, so he surprised me with another Bravo dryer to match the washer. We put the other dryer in storage and were happy with our purchase until April. In April 2012, the dryer stopped working. It wouldnt dry the clothes at all, and every time we tried to dry, the dryer was filled with wet lint. We were only a week away from moving again, so we waited until we got to the new house. The new house had gas hookups. So, we put the dryer that didnt work in storage and were thankful we didnt get rid of the other dryer. Now, just a few months later, the gas dryer isnt drying and is having the same issues as the electric dryer. How very disappointing! Both dryers are broken now, and it has only been 2 years. Each dryer has gotten about a year of use and then both quit. My husband, I and my two-year-old dont do that much laundry to break 2 dryers. My old GE washer and dryer lasted for years and is still working. We gave them to my husbands aunt who uses them and loves them. I agree someone should start a class action against Maytag. These issues are ridiculous!

I had a Maytag dishwasher that I purchased around 2005. I had no issues with it at all. Then, I got a notice that it was being recalled due to a fire hazard. My options were to either get a repairman to come out and fix it, or get a credit towards a purchase of a new dishwasher. I chose the second option. Even after getting a credit, the purchase cost was way more than my original dishwasher. I purchased the new dishwasher in June of 2010. Last spring (May 2012), I noticed a gap in my hardwood floors around the sink. A flooring rep looked around and said he would bet that theres a leak either at the sink or the dishwasher. I took off the front kick-plate to the dishwasher and discovered a wet spot. I monitored that area and discovered the leak coming from under the dishwasher (around the float switch). It wouldnt leak all the time, but every now and then, it would leak half to a full cup of water. I had the hardwood floor fixed (cost $350). At the same time, I schedule a service repair through Maytag. They sent a rep from a local repair company (Convenient Appliance Service, Inc.). The service rep couldnt identify the cause of the leak but said it was more than likely the seal around the door. So, I paid another $160 to get the repair done. I monitored the leak for a week and had no problems, so I put the kick-plate back on. In September 2012, I noticed a wet spot in front of the dishwasher. I took off the kick-plate and discovered that the dishwasher was leaking again. This time the leak was worse. It would leak 1 to 2 cups of water during a wash cycle. I called the repair company and they came out free of charge to take a look at it. The service rep said the float switch had gunk build up in it. He cleaned it out and said that should fix the problem. I monitored the area for 2 weeks and everything seemed to be fine. Last week (March 2013), I noticed some gaps in the hardwood flooring around the sink and dishwasher. I pulled off the kick-plate and discovered a wet spot. I ran the dishwasher and discovered that it leaked a ton of water (over 4 cups). I contacted the repair company that came out last time, and they said they would have to charge me $100 plus to come out and take a look at the problem. The rep recommended contacting Maytag. I contacted Maytag and they said I would either have to pay $129 for a service call (not including cost for parts), or $269 to get covered under their Repair Plus 1 program (everythings covered and it adds 1 year of warranty my dishwasher). I asked at what point Maytag would replace a dishwasher. The rep said when it is deemed unfixable. Other than that, they just keep coming out if I have issues. Part of me thought I need to cut my losses and just rip out the dishwasher and get a new one (cost somewhere around $700). But I went with the Repair Plus 1 program in hopes that they can resolve the issue. But Im definitely going to have to get the hardwoods ripped out again. It looks worse than before. It’s probably going to run another $500.

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

This has to be the biggest joke in the world for the respected name of Maytag! The engineers that developed this worst-of-all machines on the market must have been circumcised with pinking shears. 80 minutes for a wash cycle? Even rapid wash takes an hour of slowly spinning and spinning ad nauseam with almost no water. The clothes sit in the same position even on the very brief agitation cycle... Nope, the clothes do not come out clean, although if you add bleach to the dispenser, since there is no water in the tank, the bleach does triple duty and rots the clothes. Is this masquerading as energy efficient when all of the cycles are an hour long, about? Unfortunately it takes water to clean clothes and the environ-lack-of-mentalists must have bribed Maytag to develop the worst washer on the planet. Absolutely!

I purchased a Maytag refrigerator (MBR2258XES4) from Home Depot in 2012. I bought a five year extended warranty. It started leaking at the bottom. Repairmen said defrost drain clogged not covered! Cost: $180. DO NOT BUY MAYTAG, N.E.W. (Asurion Co.) warranties or Home Depot appliances! This is text book deceptive advertising. At no time did Home Depot associates in Kitchen and Bath departments say that this common design flaw existed and that it was not covered under the N.E.W. Asurion warranty which cost me an an additional $150.00! I am interested in joining a class action lawsuit against Home Depot and Asurion Co (N.E.W.) warranties.

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

The washer doesn’t have enough water to to get clothes clean. Even on deep water wash there’s is not enough water. It doesn’t get clothes clean, its very noisy. It takes a long time to was, even on short cycles. You can’t soak dirty clothes, it has a cycle for soak but it is not long enough. After about 3 months the lid licking doesn’t work and the progress lights remain on and never go off. This is the worst washer that I have ever owned. I just want to return it and get a different one!

I purchased a Maytag front loader washer less than a year ago. Based on their deceptive advertising, Maytags rarely need service (model MHWE201YW00). There was a loud banging within 11 months. I called service for the additional warranty I purchased. The service man told me this machine is shot. The bearing completely broke and the drum was loose. They ordered 3 huge boxes, 3-1/2 feet cubes delivered to my house. I had to drag them into my garage where they have been sitting for two weeks. I am now 4 weeks without a washer with 4 kids. Ive called Corporate Headquarters and have spoken to their Corporate Board Gwenn and Jackyln who seem to think they can diagnose the problem. I told them the machine smelled like it was burning and the last load was dripping wet and the clothes smelled burnt. This is a stackable in my kids bedroom and I told them I was concerned about an electrical fire. Ive already missed one day of work for this. I am now being told Jan. 11, 2013 is when it can be serviced. That would be 2 months without a machine. They are willing to endanger my children with wet wires and an electrical fire. Mr. Fettig is impossible to get in touch with and this customer service center apparently has no supervisors. What they say, goes. A class action should be started against Mr. Fettig and his team of crooks who are putting crap out into the market place, falsely advertising it and then not backing up when their product breaks less than a year and becomes a possible hazard in someones home. Ive sent to his home address a UPS letter to Mr. Fettig, letting him know if a fire starts in my home due to water on the wet wires (water that got behind the drum because of the faulty bearing), water that was leaking from the bottom of the washer that I hold him and his company personally responsible. They have been alerted to the problem numerous times and ignore it. I spoke to their Safety department and I asked what to do if I smell a burning smell when the machine was running. They told me to immediately shut it off and unplug. Yet Whirlpool is trying to put a Band-aid on a machine that has already been infected with water damage to the wires. This has been such a frustrating, stressful experience. Even 5 weeks from now, when my replacement parts are put in, I will worry each time the machine is run if there will be a spark from the damaged wire. Something must be done legally to stop these crooks from doing to this and getting away with it. All they care about is their profit margin. The Whirlpool creed to their customers is a bunch of bull! Mr. Fettig vacations at his home on Dolphine Island, Alabama while hardworking people are scrambling around trying to figure out what happened to their new appliance that promised to work but is broken in less than a year. He vacations at his home in Florida while the hard-earned money you spent on his product is a waste.

This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

My Atlantis dryer has never been able to be used on more/less dryer settings, I have had 4 repairmen repair my dryer 3 were while dryer was under warranty to fix the same thing 3 times wiring 4th time, anyway last repairman said my More dry wont work because I never had a sensor installed in my dryer and there is not a place for one so since 2005. Ive used timed dry only or my dryer runs all the time. I am concerned the first 3 repairmen never caught this. I should not have to be responsible for this either. Please have a manager contact me and have them check into my Atlantis Maytag dryer bought in 2005 and all the repair slips sent to Maytag.I used Green Yates in Joplin. Pretty sure. I thought I just had to live with it they would put new parts on I think timer, thermostats anyway can someone tell me for sure or inspect for yourself. I am single and dryer never used that much. Concerned Consumer, Nancy **/ Nancy ** as that name had front loader set from Maytag that I was very pleased with but sold with home in KC area, wish I had that set again I was very pleased .Thanks for your time.

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

I bought the dryer (Maytag Gas Bravo Dryer) from Home depot in December of 2010. The thermostat went out in July of 2011 and has replaced the same part 5 times up until August of 2011. Then they put a new burner with a thermostat and it lasted till June 1 of 2012. Now the warranty is out, they want me to repair this piece of **. I will never buy a Maytag product again.

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

Maytag MBD7749SB - We purchased this dishwasher for close to $800 at Home Depot. After close to 1 year we had to replace control panel. After another 5 months we have to replace control panel again, but product warranty is only 1 year. Now we have to either buy new warranty for ~$250 or replace control panel for same amount. Customer service: terrible. We will not buy product from Maytag again.

Peeling of paint off the oven finish, inconsistent heating, fan goes on and cant shut off until the oven cools, have to leave door open in order to shut fan off. The paint peeling is really bad. It is right where the heat escapes from the oven, have to touch up paint every so often so it doesnt look so bad and the discoloration is covered besides the peeling.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

I have a Maytag washer and dryer. The washer is a top loader with a metal drum. You can hardly hear the washer while it is running, and I have had no problems whatsoever in the past six years of ownership.

Theres nothing at all good about this machine. It is impossible to work with. Ive hated it since the day I got it. Dont buy it, ever, ever, ever. You cant put additional items in once its started, you cant adjust a load thats uneven and get it to complete a cycle, it takes forever to do one wash and it often rinses multiple times and theres no way to stop it. I HATE THIS MACHINE. HATE IT. LIKE ITS A PERSON. HATE. Is that clear enough?

Just passed warranty period and Maytag dishwasher broke. It would not start. Called and was allowed to purchase extended warranty for $135.00. A new panel was shipped and dishwasher lasted just under one more year with same issue. Another extended warranty was offered for $199.00. Needless to say we are buying a new dishwasher and not a Maytag or Whirlpool. The panels are notorious for rusting out. Hmmm moisture of a dishwasher and parts easily corrode.

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

This washer does not distribute enough water to wash clothes properly. I continually take clothes out of washer that are not completely wet. My darker clothes have white spots of detergent on them that did not get rinsed off. This product should be pulled from the stores. We have tried everything, using deep water wash, bedding wash, to get more water in the machine. Our clothes are not coming out clean. Complete waste of our money!

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

I spoke to Destiny today at the Resolution Center, she knew one phrase, its a low usage washer. I would reply, 3 inches of water in a drum does not wash my familys clothes. Every load is covered in white soap specks, whether powder, liquid or pods are used. Again, Id hear, its a lower usage washer. Ok, I got it.The machine has been cleaned with Affresh.This washer cannot clean a single shirt let alone a full load of wash. Maytag (actually made by Whirlpool) should be ashamed to produce such a shoddy product and expect to the consumer to keep paying for repairs. From reading the reviews on a couple of websites, consumers have to keep repairing this washer time and time again. Destiny told me she would send a technician out at my expense. The machine will be in the landfill on Saturday. Never again Maytag/Whirlpool.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

The fridge is very loud, leaks water from ice maker, runs all the time. I have had two repairman out to try and fix it but still not fixed. It is one year old now. If I could get my $2100.00 back I would take it and run. It so loud we have to turn up the TV so we can hear it. Drives us crazy.

Bought new and only had one service call in 20 years. The control panel was replaced. Since then, the dishwasher has performed well and, factually, was far less expensive than many other models! That figured in our decision when remodeling our kitchen back then.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level not correct, binding laundry together and replaced the same parts with cheap parts over and over... just wanted clean clothes in a no frills washer. NOT with this washer. Owned it 3 yrs and disliked it the first half washed load... $869.00 heap of junk.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

I bought a (Maytag brand) Whirlpool washer but it didnt clean clothes, so I had a repairman out. He ran it through their test and agreed that my clothes had lint, pet hair, and dirt on them, and said that was as good as it was going to get. No one called back from Whirlpool. I called them and a second repairman came out, but it was the same story. I got the same repairman back out again after several calls to Whirlpool and listened while he called in and answered questions from Whirlpool - Is she using HE laundry soap, etc. - the same things they asked me. I bought the machine because it was supposed to have one of the largest capacities available. I stood there while the repairman told them that the clothes hanging to dry were covered in lint, dirty, and extremely wrinkled because they twist into a big knot in the machine, among others. No one called back again, so I called them. The service representative told me that I was loading the machine wrong, I was not using the right soap, and that the report they got from the repairman stated that the machine was working as intended. I told them that I was standing there as the repairman told them that my laundry was not clean. They told me that it was not what their record stated. I thought washing machines were supposed to get laundry clean and get the smell of body odor out. They suggested that I use the bulky setting, so I asked them if I should have to use the bulky setting for a load of underwear. They said that the machine was working as intended, but I wanted to have someone else come back out. The appointment was scheduled, but then the repair company called me and asked if I was aware that I would have to pay for the service call. I explained that there must be some kind of mistake because it was a new machine. She told me that Whirlpool had been doing this for a while and they werent sending out repair techs anymore without notifying the customer, and that Whirlpool has been doing it as standard practice for some time now. I requested a written statement from Whirlpool about the incidents but I was refused.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

On June 17, 2013, we purchased this over the stove microwave for my elderly parents. They use it daily to heat their lunches. In December 2014, it would stop turning and finally in January 2015 it completely died... no heating and no turning. The technician quoted a repair at $200 when we only paid a little more to purchase it. I emailed Maytag to tell them that it was manufactured and purchased in 2013 with light use and that it should never have died in such a short period of time. An e-Solutions Specialist contacted me to tell me that they certainly understand my frustration, but that occasionally failures occur and that there was nothing they could do. I replied back that they could DO something because they were customer service and that was there job. No reply back yet, but after seeing so many of the same issues here, Im not holding my breath and I would never buy or recommend a Maytag product of any kind to anyone. I dont expect 15 years from an appliance, but I certainly think 18 months is just wrong.

I purchased my first and last Maytag double door bottom freezer in Aug 2018. The ice maker shoots ice out all over the floor, only half make it into the glass. It also sounds as though ice is falling down inside door. I had the ice maker replaced twice, the gasket as well, the back removed to check for water line blockage NO avail. Before the first ice maker replacement it sounded like a freight train. I questioned whether I had received a store second from Home Depot or a return as the stickers inside had been removed but HD couldn’t assist and Maytag didn’t care. Definitely NOT worth the 2000 I paid.

It takes almost a whole day to wash 1 load of clothes. The clothes dont get clean! The spin cycle wont let you spin. It runs your electric bill up! This is not a energy saver! I am so angry and disappointed! I thought Maytag was Supposed to be the best. Yall failed me. I wish I could get my money back!

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

I bought a Maytag washing machine September 2017. The lid is cracked. We were told by the repairman today that this is a common problem. The quote for a new lid was over $300. Of course we are not going to spend that much for just a lid. We will be buying a new washing machine and will not be buying a Maytag.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

I purchased model number MF12067AEW in 10/07. Motherboard has been ordered to be replaced. I have been waiting 2 weeks for the board--all over the Xmas holidays without a refrigerator! We bought this model and paid $2,800 to have a counter-depth refrigerator. I will never by anything from Maytag again. We are holding our breath to see what the cost will be and if it will it break down again. We lost all the food in the top. Ice machine flap continued to pound open and shut all the time.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

Bravos XL MCT model#MVWB835DW. Bought this new. After 2 weeks called Maytag. Washing machine did not work. I called off and on for 7 months to Maytag customer service. During this time they tried to do troubleshooting over the phone. Sent technician out. He said that there was problems with this model, that they were working on updates and would get back to me. 10 months after installation, technician came out. Washing machine worked, but still took 2 to 3 hours to wash one load of clothes. Started calling Maytag again. Washer now take 3 to 5 hours to wash load of clothes. You also have to do extra spin cycles (1 to 9 times) to get water out. A year later they send technician out. He tells me that this machine wasnt made to do loads larger than medium, that it cannot wash heavy items such as sweaters, sweatshirts, towels, blankets or comforters. That the normal cycle is not to be used. This is not a working function on this model. It is there because of regulations. Called back to Maytag. They said it was out of warranty and that there was nothing that they could do.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

Purchased Maytag dishwasher Model Number MDB7749AWM1 in June 2011. With a two person household, we need a new control panel in Sept 2014. Total cost of service call, repair and part is $325. This unit was a poor value for us. I see the trend is to discontinue a model after a short period of time, making it impossible for anyone to get a review of other peoples experiences. I went with Maytag because of this. It was a company with a strong reputation for quality equipment. Not so anymore. I would not purchase another product made by Maytag.

I love the front loading machines. Fabrics dont get beat up like they do with a top loading machine with an agitator. My Maytag front loader doesnt have as many bells and whistles as others, but I love it nonetheless. Reliability was very important to me when I bought it, so I talked to a couple repair men to see if this was one they worked on a lot. When I found out they didnt, I bought it.

Bought a new Maytag High Efficiency washer. I followed the directions closely, using the proper type and amount of soap, and the proper settings for the soil level. The clothes come out of the washer smelling almost the same way they went in. I contacted Maytag by email. Their response was to send me instructions on how to operate the washer. I responded again. Their response was basically Sucks to be you. This is the worst washer Ive ever owned, and the customer service is truly awful.

I have a Maytag dishwasher and the bottom rack has rusted out so that it cant hold dishes. The dividers break at the bottom. I was told by Maytag parts that this is a common problem and theyre hearing from a lot of consumers about this, but it will cost $196 to replace.I spoke with customer service who told me that dishwashers only last 8 to 10 years” and since mine is 8 years old, I should expect that it would rust. Thats unbelievable. They wont replace the rack, nor offer it at a discount.

My 1 year old Maytag Bravos 300 dryer caught fire on Nov. 21, 2011 after the first one was replaced. Firemen came. Luckily, it didnt spread to the house. The first one wouldnt dry my clothes.

I have not been satisfied with this Bravo washer since purchased 4 years ago. I have been holding back anger, hoping things would somehow improve. Clothes are never really cleaned, cant even fill washer with very many clothes because the washer goes off balance. It takes a lot longer to do laundry. Clothes spin so fast they are in knots when I put them in the dryer. I always have to iron clothes. Today, well today we have a leak coming from under the washer somewhere. So please tell me, what is the advantage to having a HE washer again? By the way, no warranty since its been 4 years. I will never buy another one.

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

I purchased a Maytag Dishwasher (MDB7749AWW1) just over a year ago from Sears. I did not get an extended warranty since the appliance wasnt over $1,000 and I thought I would take my chances. Sure enough, about one month after the warranty expired, it all falls apart. There is something wrong with the control panel and I cant get anything to work. Ive been looking online and see that this is a common problem. So rather than throw more dough into the money pit, Im purchasing a new, simple, uncomplicated GE Americana washer from Home Depot for $279. I figure this will cost me less than going through the repair dance with Sears and Maytag. I will never purchase an appliance from Sears again. Ive been through the mill already with a $2,000 Jenn-Air range that has broken down five times in the past three years (2 times it was the control panel). I was lucky that I purchased the 5 year extended warranty on that one, but never, ever again will I deal with Sears.

Purchased a Maytag Bravos top loading washing machine in Sept. 2015. First time we used it the machine vibrated enough to shake the walls. We thought the balance was off. Called Lowes (installers) and they came out and said it was level. There was something fishy about the grinding type noise it made. Also noticed that in spite of all the noise that the clothes essentially stayed in the same spot while the basket moved. Sometimes the clothes on top never got completely wet or rotated through the wash water. Called Lowes again and they looked at the machine and said it needed replaced. But the 90 time period for replacement had passed. Lowes said it would be repaired. A technician came and replaced the basket, saying it might have been out of round. He left, we used the washing machine and it was worse. He came back an hour later and talked with Whirlpool and they said there might be something wrong with a gear. Hes going to replace the gearbox sometime. Meanwhile we are stuck with a washer that makes a lot of noise, vibrates terribly and doesnt appear to do much washing. If noise equated to cleanliness then it would be fantastic. But had we known about the noise or the many complaints we would never have made this purchase. Whatever happened to Maytag quality? Bet that Maytag repairman isnt lonely anymore.