I am replacing my second Maytag Bravos washing machine. My first had heavy use and I rationalized that the 5 year life span was due to the heavy use. The one that I am replacing now is only 3 years old and has only done laundry for one 67 year old woman. It suddenly needed two parts with a repair bill that was going to be over $600.00. I decided it was in my best interest to spend a couple hundred more and replace it. I will not be buy Maytag again. The appliance company that I have bought most of my appliances from recommends Speed Queen which ironically also has a full 10 year warranty on all parts and labor.

I purchased this washer in January 2017 at our local Home Depot here in Mexico. It was a washer/dryer combo. Now, in July, a mere 6 months and only a few wash loads later, it has gone from the worst machine I have ever owned to what I consider to be garbage material. First of all, it boasts about not using much water. This is true... Only 1/4 of your load is in the 3 inches of water at the bottom of the machine and the top 3/4 never even gets wet. I couldnt believe it. Now, I put 2 sheets in this morning and it fills almost to the point of spilling out, though I have to give it credit for shutting off the water before it actually did so. This is a NEW washing machine!!! I, along with a lot of other folks from what I am now discovering, are all in the same boat. I remember Maytag being a mark of excellence way back in the day... This is no longer the case. Stay away from this company... I know I will.

I made the mistake of buying a Maytag fridge and dishwasher when I moved into my home 16 years ago. Ive had nothing but trouble with these inferior appliances since almost day one. The seals on the freezer quickly started to separate, causing ice chunks and insufficient temperatures. We had an extended warranty, but they refused to replace it. Weve had that fixed approximately 10 times - never resolved it. The plastic covering on the dishwasher racks began to peel early on, which caused the metal underneath to rust, in turn causing the clean dishes to come out with little rust flakes all over them. This company obviously cares only about profits. Save yourself a ton of headache and DO NOT BUY MAYTAG.

Within the first 2 years, the dryer stopped heating. After a $300, a few parts and a few attempts to repair the dryer worked again. The sensor still kept saying check the vent and we gave up and removed the outside vent cover. Works great now. The washer worked great until year 4 when it began to sound like a helicopter. It got so bad that it literally hurt my ears and could be heard outside. It also leaked. Called repairman and they couldnt even remove the drum because it had rusted solid. After a total of 4 years we are replacing the set. Do not WASTE your money!

We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

I purchased the Maytag Neptune pair in 2002 and was never informed of the product recall/class action lawsuit for the washing machine which occurred sometime around 2004-2005. We have had many problems with our washing machine over the years and ruined many clothes with what appears to be bleach stains, even though no bleach was used in the cycle of wash. I had to replace the board which controls the latch on the door and the clothes that are washed are not clean and have an undesirable odor to them. I would have been part of this class action; however, I was never informed of the lawsuit. I called Maytag today and they advised I could set up an appointment with a service person; they did not want to honor my complaint as the class action lawsuit has been resolved and they are not handling these types of complaints anymore. My children have started a new school after semester break and their brand new uniforms are now becoming ruined due to this defective machine that Maytag will not take responsibility for. What type of recourse do I have? I will never purchase a Maytag anything if this is how they treat their customers. Problem will not go away by hiding their head in the sand. Now I have to go out and purchase a new washing machine because Maytag didnt inform their customers of the inherent defect in their product and take care of them accordingly.

Maytag microwave MMV4205BAB - I purchased this microwave in 2007. By 2009, the whole inside was peeling down to the metal. Under the glass plate, the bottom is all rusted. Ive called customer service every year since 2009 and they say the same thing. No extended warranty, nothing they can do. They acknowledged that this was not normal, but they did nothing! Do not buy anything from Maytag. If you do, buy all of the expensive warranties or you will be sorry like I am.

It does not matter what mode you select, every single piece of clothing comes out a scrunched up wrinkled mess. I have to wash all clothing in bulky sheets mode because it is the only mode where the clothing actually gets submerged in the water. This washing machine is extremely loud and it is without a doubt, the worst purchase I have ever made. I have never written a review before, but this product is so horrible and frustrating. If I can persuade one person not to purchase one, I feel that I have done a good deed.

I have NEVER written a review however I am compelled to write up and if I can save at least 1 family from making the mistake I did then my review will be worth it so just before Christmas last year I treated myself to a new washer. I looked at so many. Only 2 things on my wish list were 1) American Made and 2) have a large capacity for blankets and bedding. Well, I was so excited about my Maytag Bravos XL Washer but my excitement didnt last long. 4. There is a major design flaw in this machine. I have given it plenty of time and have tried to talk myself to liking it but when you have to wash the white loads at least 3 times to get them clean and still not getting the results expected then its time to admit to yourself that I made a mistake.The large capacity drum is an irrelevant because once the clothes are wet they become too heavy for the drum base to actually agitate the clothes. What ends up actually happening is your wet clothes sit in a pile. The user tends to scale the loads back to help the machine. The above problem is partly due to the fact that the machine NEVER fills up the drum with enough water to submerge the clothes where perhaps they would be able to move freely with the base agitator and the drum rotating. This model was marketed as water conserving however we find ourselves washing loads 2-4 times to achieve the desired outcome. Conserving water at this point is a joke... we end up using more water and energy to get a load of clothes clean.Bleach dispenser does not empty completely during the white cycle even when less than recommended measurements are used. If a load of whites needs to be washed we have to wash with bleach on the 1st go, and then 2 more cycles without bleach. Otherwise anything washed after the whites gets spots of bleach on them. For these and many more reasons this machine should NOT be on the market and especially not for over $800 USD! And I would not want this product to represent US production. It does not deliver on any of its selling points and is overpriced.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

My Maytag model MDB7749AWWI was purchased from Home Depot on March 10, 2011. On July 12, 2012, my dishwasher would not start. I had out of town guests and then the repair person was out of town, so I did not get anyone out to look at it until July 31. He stated that we had bad controls. The parts would be approximately $420.61. He could not get any parts because everyone was out of this part. Does that mean that all the dishwashers of this model number are broken? Is there a recall? This is unreal. When I was asked if I wanted extended warranty, I said no. If I needed an extended warranty, the equipment must be junk. Well, I needed the extended warranty. It is junk! I will never, never, never purchase another Maytag appliance as long as I live!

Purchased the Maytag Bravo Nov 2010 and had to replace it after just 5 years. In the five years we owned it, it required a new water pump and the stabilizers had to be repaired. Its motor burned up and I was not able to find a replacement. I was quoted $224 (parts only) for a replacement motor and 10 weeks delivery. My wife never liked the machine as it was not able to clean clothes that well. We did not find much difference in any of the settings. We tended to put very few clothes in each load in order to get them clean. We were dissatisfied that it did not have a soak cycle and the lid lock was particularly annoying.

I purchased the Bravos XL washer and dryer from Lowes in March of 2011. I had only had my dryer for a couple of months when it stopped drying out of nowhere. The repair man came and replaced the fuse assembly and all was well until December 2011. Again the same problem happened. I had to wait almost 10 days for someone to repair it. Once again in January 2012 for the second time the fuse assembly was replaced. Its now December 2014 and again my dryer has stopped working. Have to wait again 10 days for anyone to come and fix this. I will never buy another Maytag dryer again.

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

Maytag dishwasher from Home Depot, model MDB7749SBM1. Bought it last May from Home Depot - in a little more than one year it has already needed 2 repairs to the control panel. We are having a lot of problems finding someone to come and repair it. We want our money back. This is a piece of junk!

My husband and I just purchased on 4/8/17 a BRAND NEW MAYTAG 4.3 CUBIC FEET CAPACITY FRONT LOADING WASHER WITH STEAM AFTER OUR PREVIOUS 15 year old washer that we both used just finally started having issues. So we decided to go new and with front loader with good brand. How sadly I was wrong! We brought our washer home, hooked it up and turned it on with 1/2 load of tiny laundry. It didnt even make it through one load! This POS started throwing error codes E1, E2, F8, F9, Suds and wouldnt drain any water. We reviewed the manual again, checked the filter hoses and detergent. All was fine but washer wouldnt work! I called Maytag 2 days later on Monday and after repairman came to look at it Thursday said it needs new drain pump and today now power wont turn on and nothing will work on front of machine, mind you this machine is brand new! I am so disgusted and angry that any company would sell this quality to anybody and at the prices they charge! NEVER AGAIN WILL I PURCHASE ANOTHER MAYTAG!

I bought a set of 4 Maytag kitchen appliances. Terrible quality. Dishwasher racks poorly designed for anything except standard size dishes. Microwave has a hotspot and explodes whatever Im reheating. But refrigerator is the worst. According to my service man, Maytag is aware of known issue with poor quality evaporator coils that erode quickly, leaking freon. Causes problems with ice buildup in freezer, poor ice production until it loses enough freon to stop chilling correctly causing food spoilage. Im to that point now. This fridge is only good for offshore fishing site. Whirlpool is aware but will stall as long as possible, then refuse replacement, but they will offer to help you replace the appliance. HA! Fool me once, shame on you. Twice, shame on me.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

It has all the features we like and use every day. Timer, lights, fan, built-in Above stove, use minutes or preprogrammed Turntable, quiet, white in color, easy cleaning. Easy to replace filter and light.

I have purchased my top loader Bravos washing machine 3 1/2 years ago and I have had nothing but troubles with my machine. I have had to replace the motherboard twice and I constantly have that foul smell in all our clothes. I have to wash each load twice and still the smell doesnt come out. I have also complained numerous times about the water level not being correct, but they keep saying that is how the high efficiency machine is. I can watch my load washing because we have the clear lid which I like. But at the same time, it gets me really angry seeing how this doesnt clean clothes like it should. I dont believe that the water levels are right at all. I have clothes that dont even get turned over as they are washing and I have even smaller loads than before. I can only clean 4 adult pairs of jeans at one time and I still think that is too much. I clean my machine every time the red light turns on with the Affresh tablets and sometimes I run a clean cycle with just bleach. Maytag has done nothing to try and correct these problems. Its so sad that I have to take my clothes to the laundry mat to go wash them and there I have absolutely no problems. They have the HE front loaders and they have enough water to wash my clothes and I can actually see them being washed. I will never buy a Maytag washer or dryer again. How sad you have all these complaints and no one to help you fix or correct them the right way.

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

I share the complaints of others about the Maytag Bravos washer (model MVWB300WQO), which I purchased in October of 2009.Besides being overpriced, its a washer that doesnt soak clothes, develops a bad odor, has silly things like unnecessary lights and music, and you cant add an item once the wash cycle has begun without the cycle starting over from the beginning. It also leaves washed items in twisted wads and the lid locks so you cant see whats going on inside. In addition, it damages items. Ill have to replace a full-sized blanket that it recently destroyed and now I cant trust that itll wash things safely, which is a problem. The person I spoke with at the companys customer service department simply said that I shouldve used the bulky item option instead of the regular cycle. I explained that Id used the bulky item cycle before and the same thing happened. The washer leaves larger items stretched very tightly across the tub and I suspect that is how my lightweight cotton blanket was destroyed. She offered to schedule someone to service the washer. But its not broken, its a poor design, so sending someone here would be a waste of time.

Original owner of $800 HE top loader washer since 2010. We heard a grinding noise for months, then finally it seized up. Repairman quoted me $300 to replace bearings. The repair guy seemed a bit too eager for the job, so I knew it must have been easier than expected. I Googled the heck out of it, and used this forum heavily for guidance. Seems the bearing failure is a pattern issue. It also seemed ridiculously involved and no one had posted a how to video matching my model’s layout. I took a peek with my own eyes and noticed a sock had gotten under the basket. The sock got caught in the drive belt and knocked everything loose. I removed the debris, tightened the pulley and everything worked. Cost me $0 to fix myself. So buyers beware before repair. And check the error codes yourself when in doubt! The first thing I did was check error codes. Found a great video here **.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

Purchased a new Maytag refrigerator in January 2013. In September 2013, the ice maker stopped working and Maytag sent out a repairman to replace the ice maker. In February 2014, the ice maker stopped working again. I contacted Maytag and was told the refrigerator was no longer in warranty. I told them that since the ice maker was replaced in September the warranty should have covered me for a year from that date. The Maytag representative told me that was not had it worked and asked if I wanted them to repair the item for a fee. I bought a non-Maytag ice maker and replaced it myself. It is now July 2015 and the ice maker is still working fine. I am not a repairman.

Bought a new Maytag Over the stove model Microwave from Lowes. It worked fine for a while. Then it started saying open close door. We opened the door and closed it, and sometimes it would work. This went on for a while till it finally would not work at all. Called for repair, the service guy came and took it apart and one of the door switches needed adjusting. He left and it was working, good deal. 2 days later open close door started all over again. We found if we lifted the door when closing it, then it would work sometimes, until one day it would no longer work. We called for another appointment, and got a new company to fix it called ABCO. The service guy showed up and tightened a screw and it worked again, said the other service guy might have forgot to tighten it down. I tried it and it worked. We did not touch it again till next morning and back to open close door again. Called ABCO back and got a new service time for Wednesday next week. Wednesday came and went, called to see why no show. They said we were not on the service list and were very sorry. So we set up a new time for them to show the following week Tuesday between 12 and 3 pm. At 3:49 they called and said sorry, but they were not going to be able to make it today. I told her then get us tomorrow and was told they were very busy and maybe Thursday would be better. I told her we were in line and and should get service before others that came on later. Her reply was maybe Monday of next week was better. After the runaround she said they would try for Wednesday tomorrow, but no promise made. After that I called Maytag direct and they said nothing they could do except make another service appointment. She told me I could get a service appointment tomorrow Wednesday between 8 and 12am or 12 and 3pm. I asked with who this time and was told ABCO who just told me they were too busy to show up tomorrow and had put me on standby. In the meantime I paid over $300 for the Maytag microwave that is never going to need service because the Maytag service man is so lonely. And bought a $ 200 Panasonic counter model so we could have a working microwave. So now we are in over $500 and still no Maytag working microwave. They did send me a letter offering me a discount on extended service plan if I want one. I told them it would be cheaper after the one year runs out under warranty, to just junk the microwave because it has cost me way more in wasted time, waiting for the lonely Maytag repairman to show up. Bottom line do not buy a Maytag Microwave model MMV4205DS-1 unless you just want a good looking decoration over your stove with a nice light, and have plenty of time waiting for the lonely Maytag repairman.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

I bought a refrig from Home Depot on 10-16-2012 two years ago and it doesnt work, but they only put one year warranty on. So had to go out and buy another. My complaint a refrig should last more than two years but they were going to send repairman out on my expense and more than likely would of cost me the price of a new one.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

Maytag topwasher 2011 model MVWB300WQ2, SERIAL C11271134 - Im from the old school, expecting to get my money worth. I purchased a Maytag Bravos automatic washer in 2011, now less than 5 years later, it has a very loud knocking noise during the draining and spin cycles.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

The functionality of this machine is so awful. I had the dealer replace it only to find that the awful noises that the machine makes, the fact that the clothes don’t get covered by the water and the clothes are so knotted after the spin cycle you have to untie them is normal for this awful appliance. In the sensing stage the machine groans like a laboring motor around 30 times, then stops with a jolt. My machine is next to the bedrooms and the noise wakes people up. Even in the “deep water” setting, the clothes are not covered by the water. The wash cycle is short and noisy and the spin cycle goes on forever. In the end I have to untie the legs of pants. Whoever designed this machine should be ashamed of herself or himself. Shame on Maytag.

Maytag Centennial Washer MVWC400XW2 - Bought this washer Fall 2011 -- first 6 months had to be serviced and now (February 2016) needs to be serviced again - has not cleaned my clothes for the last 3 months. Now, I have had to order a new washer - you can bet it wasnt a Maytag. My new washer will not be delivered for another 3 weeks. Past the part of not cleaning clothes, now it wont even empty the water, or pump out the water. It makes a horrible noise! Before it wouldnt use any water, now, it fills completely up. I do not know if it will make it through this current load much less another 3 weeks. Always bought Maytag before BUT WILL NOT AGAIN - after what I have been through with this washer!

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

I suppose I am the lucky one in that the Maytag Bravos was given to me free. I took out a perfectly good Maytag standard agitator washing machine and replaced it with this several years old unit. What a mistake! I read the other reviews and see that I share the same problems. I always get a the oL fault as soon as it goes to do the final spin. So I have to reset and try again. Also I have seen the same kind of dirt on the clothing as others report. I dont know that I will waste my time contacting anyone about the fault code. I may just put the old one back in and scrap this thing!

Maytag Bravos XL - This is the worst product I have ever owned! I purchased a Maytag because when my husband and I were married 29 years ago we bought a Maytag washer and dryer and still using the dryer. However we lost the washer and had to replace it. Worst mistake ever!!! Within a year a circuit board went out (they replaced but I was advised I needed an extended warranty which I do have) and was told by the technician that this model was junk! I called Maytag and expressed my great disappointment and all I was told is we document customers input. I then ask ok so what are you going to do about it? And I did not get a response. I asked for a different model but was declined. As you can see it is rusting at only a 1.5 years old and tearing up my clothes. It destroyed a doily that belonged to my late mother. Maytag used to have integrity in their product but not anymore. Not only all of these issues but I have to wash clothes twice and they still are not clean. Plus they have a dirt film on them and yes I used THE detergent!!

I purchased a matching set Maytag washer & dryer June 2013. Sept 2013 the drum went out - 4 weeks for that repair. March 2014 the electric panel went out. Took about 10 phone calls with hold waits of 30 to 70 minutes and 4 months, to find out the replacement part is no longer available and the washer is discontinued. To get a new matching set, I had to pay for a new dryer and they will give me a free washer. I have to give both washer and dryer back - I paid for 2 dryers. 6 month later and more phone calls, no washer and no one will return my calls. The dryer I paid for is at the appliance store waiting on the new washer. We consumers have nowhere to go. I have heard so many similar situations. Where are we to go? Who are we to call?

I purchased a Maytag refrigerator from Home Depot on 5/17/11. It would run, then not run. It spoiled all the food not in the freezer and most of the food in the freezer. This happened early November, being less than six months old. My wife called on 11/8/11, they repaired it on 11/18/11. Ten days of no refrigerator and a lost of about $200 in spoiled food. The company would not pay for any of the money I lost for the spoiled food!

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

Both work good. Washer could be a little lower and it has quit rinsing and I cannot use it. But it is 9 years old, I think for their age they were a good buy. I plan to get the washer repaired because have been satisfied with how clean it gets my clothes and it washes pretty quick. I got the large capacity and with a very large load the washer gets them clean. The dryer is very good. It is just as good on a large load as small, dries quick. I would buy this type washer and dryer again and would definitely recommend it to folks. I have been very happy with this washer and dryer. The paint is coming off the washer where you put detergent and fabric softener in and it has rusted out some but it is getting a little age on it so this is expected. I like it, I can throw my comforter in and it gets it clean and the large loads always come out great. I think anyone who bought the set would be very happy with it. It is also quiet which I like.

I bought this over the range Maytag microwave model MMV4205DH-1 5 months ago and today a hairline crack appeared alongside the door handle. I called Maytag to find out how I can get this repaired since, as time progresses, it will become worse due to using the handle to open and close the microwave. I was told this was a cosmetic warranty which expired after 30 days. They would fix it only if the microwave couldnt be opened. Apparently, the handle can become loose but as long as the door opens, they wont do anything.I bought Maytag because of their supposed reputation. Im so glad this happened with my $300 microwave as we were getting ready to replace our washer and dryer and were looking at Maytags. Good to know they dont back their products before I spend several thousand dollars on a washer and dryer. I will NEVER purchase another Maytag. My $120 generic microwave lasted 10 years and I gave it to my son and it is still going strong.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

Maytag washer not draining properly. Called Aug 15 for help. First tech in on August 23, makes a diagnosis, orders part; no news, I call, am given Sep 15 as next date. Come 9/15, I take off from work, only to find out tech cannot come that day, to reschedule. Next tech comes 9/25 with a different diagnosis and different part to order. By October 3, an announcement that part came in, to make an appointment. By now, its been a month and a half, I am so angry. I call a friend, who fixes it in 15 minutes by simply clearing a clogged drain filter. This is unacceptable: the inordinate wait, incompetent techs, unresponsiveness from customer service. I cancelled my contract with Maytag Warranty/AIG.

Bravos XL - This machine purchased in 2014 at Home Depot service plan, needed major repairs just over a year old. Tech working on this machine replaced the whole tub assy after Maytag want to just do the cheap repair and just do a bearing kit. Reading online all the hundreds and hundreds of the same complains Maytag has done nothing in good faith to replace these junk washers!! My washer is now leaking under the washer less than a year after the last repair!! My good friend purchased the same machine and has had the same issues and his has been down for weeks because the poor service person from Maytag service broke some of the new parts! Now the washer is leaking again. WHAT can be done. This not right!!! Public needs to be warned about these flawed machines and Home Depot is still promoting these Junk machines!!!

Two years old, single person owned and will not operate - At 2:00 am, April 25th, 2012; I went to take a load of laundry out of the washer. It was still full of water and would not operate. I am a single person. I do not do load after load in two years. In fact, I was doing a weekly load of clothing, nothing large. I paid close to $1,000.00 for this unit. This sucks and why only one year warranty? Are you Maytag? A Youigo car would run better than this. And they are built cheap.

If you are considering this product...RUN AS FAST AS YOU CAN!! This is the biggest piece of junk Ive ever owned!! I would be more than happy to take back my 20+ year old washer over this JUNK!! It is 2-2 1/2 years old tops. I cannot count how many times my husband has already had to repair this garbage!!! I will NEVER purchase another Maytag appliance! My stainless steel dishwasher isnt any better!!

Maytag Bravos XL MCT (Disposable). Model number MVWB835DW3 Top load washer. I’ve read many of the reviews on the site and feel your frustrations. Let me start by saying, at least you have a choice of products. I’m stationed in Okinawa Japan and have ONE place to buy my appliances and a choice of two machines. Both of them are garbage Maytag products. The first one (model noted above) died after 18 months. NOTHING they could do! The “technician” they sent didn’t have a clue. His answer was to replace the control board. Time to receive part? Up to 30 days. Really! My option? Buy the exact same product. I can’t even describe how screwed over I feel.

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

Apparently the Maytag Bravos HE top loading washer is poorly designed. We have sparingly used this washer for approx 3 years and it began to make a horrible noise in the spin cycle and then to give us UL error codes. After searching on the internet we discovered that the seal around the main spin shaft and the bearings were bad. Inspection under the machine revealed a terrible rust and grease spot and splatters of rust and grease on underside of unit. This is a typical problem and this machine should have been recalled or at the very least repaired by Maytag for little if any cost. They now make a kit to fix this problem, but this should not happen after only 2-4 years of use on a $700+ machine. Very, very disappointed with Maytag! Customer service, of course, offered us nothing as pathetic 1 year warranty was expired. Ten year on the tub, like anything will go wrong with that.

Neptune washer maxima XL steam - Our machine is only 2 years old and we feel the soap dispenser is defective. That little door inside to choose either liquid or powder is not flush with the basic cup and to make matter worse, there is a V shape hole at the bottom of that little door. Meaning, fill it up, and while you are looking for the softener in your closet, all the expensive liquid HE soap is on your floor! And when you close the door, if you wait for starting the load, all the soap goes into that rubber gulley instead of being sent over the clothes. I just got off the phone with them, they wanted to send a technician AT MY EXPENSE - when I do feel it is a deign mistake, not a use/abuse on my part. I proposed instead to send them a picture. They refused. I proposed to send them the soap drawer, they refused as well. I will never buy Maytag ever again and dont recommend to anyone to go to this Brand name!

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

Same complaint as most of the others: bought a refrigerator in 2013 and about one month after the 1 year warranty had run out the freezer started leaking water all over the floor and build up is on the bottom of the freezer, making it difficult to pull out the metal drawer. :( We do not have the water even hooked up to the automatic icemaker so have no clue where the water is coming from. Clothes washer has never worked properly from day one, didnt fill up with enough water. Had the repair man here while the warranty was still in effect and he verified that the washer DID not fill with enough water therefore leaving soap and grime on our clothes. :( He had to order an entire new brain and replaced it. Worked for a couple of months better than it ever DID and now back to soapy, grimy, dirty clothes again. Why isnt there a recall on the part that keeps backing up on these bottom freezer Maytag refrigerators? Someone needs to start a class action lawsuit and get these things recalled and replaced. Spent a lot of money on this brand new refrigerator and was so jazzed to get a brand new one for the first time in my life. :( Well that was surly short-lived. Shame on you Maytag, your company has really gone downhill. I would love it if an attorney could start a class action lawsuit with Maytag on their bottom freezers.

We have had a Maytag dishwasher for just over a year. The control panel acts up randomly and has finally quit altogether. The design of the handle is very poor as it pulls the control panel away from the door. Will never buy a Maytag product again. This is a very clear design flaw and when we called Maytag they offered no help as we are passed the guarantee.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

Just got off the phone with Whirlpool Customer Care after getting the run around between parts and customer service for most of the morning. My issue is with the shelving on my MSF25D2EAS01 Maytag side-by-side refrigerator. The plastic surrounding the glass shelving is disintegrating and they are not admitting to a defective design only that the original part has been obsoleted and a new one is available for purchase (an over $300 expense to replace three shelves) on a unit that is just over 2 years old. I am willing to bet the old part has been replaced with a different design after they realized a substantial number of customer complaints. As an engineer, it is obvious to me that these shelves are poorly designed for their intended purpose, furthermore my work allows me to recommend appliance brands for large projects so I see no reason to recommend Whirlpool or any of its subsidiary brands (Kitchen Aid, Maytag, Amana, Jenn-Air) to any of our clients. Whirlpool quality and customer service is substandard and no better than any imported brand of appliances.

Maytag, you left me disillusioned and disappointed. I used to believe you, trust you. How am I going to feed my kids without a fridge? I bought our side-by-side French door refrigerator a few years ago and even bought the extended warranty (which no longer is in effect, unfortunately). Yesterday, the refrigerator failed, We called a small local repair person who could be at my home in a couple of hours. He listened and said my compressor was out, a leak was probably in there too, and that it would cost about 900 dollars or more to repair. When I called Maytag to see what they thought, they said that because I called a non-Maytag assigned repair person (even though this small-business repair guy didnt even take apart the refrigerator), I could no longer get their repair plus one year warranty offer which runs 400 dollars. But there is nothing I see on their warranty page that says this. Here I was trying to help our local economy by calling a small mom-and-pop repair person who is known in our town and has a good reputation, but I guess that by doing that minor well-intentioned act, it goes against Maytag corporate policy. Wow, how foolish do I feel now? I feel ashamed to admit this, but I actually started crying when I was on the phone with their customer help rep and asked, Isnt there something that can be done? I was thinking to myself that two months after Christmas with three kids is a tough time to replace a 1300-dollar refrigerator. I offered to pay the 400 dollars to get the refrigerator fixed by a sanctioned Maytag official with their warranty, but that I didnt know that I wasnt supposed to call anyone else besides Maytag if my appliances broke down. I would have never called our small local guy if I had known that Maytag corporate had such a policy. She said that no, there was nothing that she could do, and that is what happens to customers who call a non-Maytag assigned repair person. I guess when this happens to your fridge, you ask your neighbors if they can keep some milk, lunch meat and cheese for you, at least until you can save up for another fridge. Thank goodness that dried pasta and Ragu sauce dont have to be refrigerated. There are also cans of peas and corn and dry cereal, so it should be okay.I cant express how absolutely disappointed I am with myself and with my purchase, and how this has soured me on everything Maytag. I feel like an idiot. Can you believe that I had actually scrimped and saved up for months to buy this Maytag refrigerator and the extended warranty (hah, just to be safe)? I had bought it because I thought Maytag was a reputable company and because it was supposed to help the environment with its energy saving technology. But dont you think that a $1300 refrigerator should last more than 7 years (Believe it or not, this newer Maytag fridge was replacing a 20-year-old fridge that I gave to my cousins and which is still running to this day!)? And to add insult to injury, I already had a major repair done 4 years ago on this same French door Maytag fridge when it was only 3 years old. Maytag should offer to come out and fix their mess, but all I received when I called Robin, the supervisor, at their Tennessee call center was a, Sorry, there is nothing that I can do and there is no one else that you can speak to, and Nope, there is no one at corporate that you can call for help either and I have no advice to offer you. I can give you a mailing address though, if you like. I think I did hear pity in her voice, so that was some comfort. Pity from a call center supervisor, think about that! How awful it must be for her if that is all that she can offer to the desperate people who look to her for guidance! I actually felt sorry for her after I hung up the phone. It must be terrible to know that the company that you work for is probably mistreating its customers and all that you can offer is an Im sorry. I wonder how often someone says a rosary for her and her workers taking on those endless calls for help. How often does she cry herself to sleep after a day of that?I really dont like complaining online and I rarely do it, but this experience was just so awful and hopeless that I feel I had to say something to save other people pain and money. I hope that everyone learns from my miserable Maytag mistakes and please pass on my experiences to all of your friends and family. Those big tax refund checks will be coming soon, and I know that a lot of people upgrade their appliances with that money. Please, please think twice before you buy anything Maytag. I would feel better if I knew that people could learn from my stupidity. Remarkably, I was once gullible enough to trust and believe in American-made Maytag - goodness, was I wrong to do that. I am considering Facebooking my friends and family to let them know what happened and save them the heartache too. I hope that everyone who reads this can learn from my own mistakes and misguided trust in a company. In a world where so many companies throw away or roll over on their loyal customers, all I can say is something that I learned from a wise high school English teacher - Et tu, Maytag? .

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

Part on fridge is defective. They have sent the part but tell me they dont have anyone in the area to work on it. Nor will they pay for someone to come out. We must replace it ourselves. This product should be on recall. Maytag fridge. Freezer door on bottom filling up with water. We have 2 of them doing this. One about 15 years old. Other one is 3 yrs old. Maytag knows of the problem but wont fix it. Wont recall their default product.

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

After replacing plastic parts that spin tub twice, now the computer is wasted. Purchased not even 3 yrs ago, now I have to buy a new washer because the computer system is not covered under warranty. REALLY!! The most expensive part. Not worth fixing. Never washed really dirty clothes when it wasnt broke down. Agree with the class action I would be in. Dont buy people and now I am off to pay to wash my clothes.

The Maytag Bravos XL low water washing machine is very disappointing. About 20% of the time it needs a second rinse because there isnt enough water released to rinse clothing. Forget washing anything large. It just doesnt do it. Waste of money. The matching dryer is just fine - no complaints.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

We bought our refrigerator 14 months ago and it has a 10 yr limited parts warranty. Both the freezer and refrigerator quit working, right after we spent $600 in groceries. I called the warranty dept and the soonest they could get here to service it, was 9 days later cause they only go thru Diamond Preferred, to do the repairs. Then on the 9th day, Diamond Preferred calls to let us know that unfortunately, they cant get here to fix it until another 5 DAYS!! Two weeks with NO refrigerator and freezer, is ridiculous. They should pay another repair place to come out instead of just relying on the ONE!! Our food is now ruined, $600 worth. And to top it off, weve had to eat out costing us more money, and then once its finally fixed, we have to go buy more groceries. I will NEVER buy a Maytag appliance, ever again!

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

I bought my Maytag Neptune washer and dryer in 08 or 09, and it has smelled like mold and mildew for years but I still have to use it because I cant afford to get a new one. I cant get the smell out. Also, I have to take the pump apart at least once a year due to the fact that sometimes, no matter how you check your pockets, change still gets left behind and they dont make a screen or filter that will keep the change out of the pump. It is not hard to do, but the first year I had it, it were in the service center as much as it was home. I was glad when someone told me what was happening because I fix it myself in like 15 minutes and move on. But it should come with a self service manual showing how to do this procedure to save people money.

I purchased a Maytag dishwasher (model MDB7609AWW1) from Sears on 09/11/2009. Its control panel failed twice in 3 years. In 02/2011, after just 17 months, the dishwasher wouldnt work. Nothing happened when I pressed the start button. I paid $294.39 ($129 for a new control panel plus labor) to have it fixed. Now, 17 months after the control panel was replaced, it has again crapped out with the same problem. I see by all the complaints here that this is a common problem. I wish I had read all these complaints before I had the control panel replaced the first time. Maytag, shame on you! Never again! I called Maytag and Sears, and as you would expect, they said, Sorry, its past the warranty period. When I buy my next dishwasher, it will not be a Maytag and it will not be from Sears.

We bought commercial Maytag washer & dryer Oct 20th 2020. Very expensive ones. Oct 13 2021 they stopped working so had it checked. The shifter on washer went out & dryer blower is not working really!!!! Not even a year! Been without washer & dryer for 1 month because they didn’t have availability & now have to order parts another 2 weeks!! Never buying this product again!! Don’t buy Maytag!

We had a wonderful Bisque Maytag double oven in 2002. We bought new stainless appliances this year, and have been very disappointed with the range. Why do you have to hold the temp and timer settings one increment at a time to set it, and why do you have to push Start after that? Frequently we set the temp or timer and walk away, only to find that the oven or timer did not begin because we forgot the new step. When the timer goes off, you have to push it twice to get it to reset. The burners themselves have too many confusing pictures for the settings. What happened to low heat, medium and high and hash marks in between? The stove top itself is a nightmare to keep clean. Give me back my coil stove any day!!!

My home has all Maytag appliances, all just over 2.5 years and I have had no issues with any of the other equipment excepting the fridge. The fridge itself works very well when it does, but some things are just wrong/flawed with the French door fridge.1. The Evaporator mechanism is flawed and keeps accumulating frost over the Thermistor sensor, which in turn shuts off the fan and the fridge itself stops cooling rendering all the produce bad within hours of purchase. The freezer and icemaker works fine during this time. The first time a tech came in during Warranty period and put come Aluminum foil over the thermostat and zip tied it and told us that the issue is resolved. Fast forward 18 months or so, same issue. This time they want to replace all parts since the last time it did not fix it. How convenient isnt it? So now I have to shell 500 plus bucks to solve what was not fixed the last time. Flawed design is all it is; do not purchase any of the French door fridge from Maytag/Whirlpool or be prepared to buy an extended warranty and a down fridge every 12-15 months at the minimum. In my case shell out 500 bucks every 15 months I guess.2. Sloppy icemaker: Ever heard of an icemaker that thinks and drops 4-5 cubes when requested and thinks again before giving another 4-5 cubes? We see it all the time at Soda fountains. This is what to expect off a Maytag ice maker. And lord knows if you have guests, they will run through the batch of ice by the very first meal and then the princess ice maker needs 12 hours to make another batch of ice.3. Noisy fridge: Ever heard a noisy fridge in a very quiet home? This Fridge excels at that. Just about the time it shuts off the compressor, boom it goes on again.

MHW60X - I experienced a problem in May of 2015, and the repairman told me it was the master board, and he has seen this many times. He said that the MCU board goes out after 3.0 - 3.5 years!! This is exactly how old my machine was! The cost to repair this was almost what the machine cost, and this is unacceptable. I have had Maytag washers my entire adult life, and my prior one lasted approximately 20 years, but after this I am not sure I will consider another one in the future. To have a major part burn out soon after the warranty expires should not happen. I contacted customer service to find out the experience and reported problems on this model, but could not obtain any information, other than they have received calls about this model. I asked Maytag to reimburse me for the part - at a minimum, and they refused stating it was out of warranty and they could do nothing. Apparently they do not care about their reputation anymore, which is sad, since they used to be so well regarded!

I would bought a Maytag Aqualift self clean oven. I just ran the clean cycle and it is just as dirty as it was before I ran the cycle. Absolutely nothing happened. Now I have the 2 cups of water at the bottom of my oven they said to put in prior to clean cycle, that I have to get in and clean out. This is absolutely unacceptable. I would like Maytag to get back to me asap and offer a solution. **.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

I purchased a Maytag gas range after remodeling my kitchen. I thought I was getting a good product, boy was I wrong. The ceramic gas grates are so slippery that pots tend to slide off but the real problem is that the racks inside the oven fall when you place pots on them. I tried cooking a Thanksgiving turkey in it and the racks fell to the bottom of the oven. It appears that the top rack and the bottom rack are the only two that stay in place. And it also appears that when the oven is on, the sides of the oven expand so that the racks fall. I have tried to contact Sears as thats where it was purchased to no avail. I will now attempt to contact Maytag directly but it appears that I will also not get anywhere there. I have read at least one other complaint of this exact same type happening to someone else. This is very dangerous. Do they really want a lawsuit?

Me and my wife bought a Maytag refrigerator from Home Depot. The top half freezes up in a big way and it gets real frosted up I have to pull it apart every 2 months to defrost it. The bottom half starts to get warm if I dont do that. I will not ever buy another Maytag refrigerator again.

I bought Maytag Bravo washer and dryer set in Nov 2012. Washer door lock broke shortly after 1 yr and now the gearbox has broken. DO NOT BUY MAYTAG BRAVO WASHER. The cost to fix is more than the value. Before the gearbox death the sound it made while spinning was so loud you could not hear the TV or have a conversation in the west end of the house. Visitors were stunned at the noise it made. I called Maytag warranty and explained I am having the same issues as everyone else, what are you going to do? The answer was nothing. Please read the other reviews, same issues. It never cleaned clothes anyway, bad design, bad company and bad corporate values. Model number MVWX700XLE.

No problem with retailer. Problem is this top of the line Maytag dishwasher, Model# MD8895lAWW. Stinks all around. Takes long to wash and load, times are far apart and too few so holds few dishes. Dishes and glasses break because of the tine spaces. Horrible dishwasher for high price. I hate it so much it upsets me daily. All I get is a sorry from Maytag. Its not that old, only a year and a half. Why no satisfaction? I will avoid all Maytag products for life.

I purchased a Maytag fridge with a freezer on bottom. As you know there are many complaints regarding ice build-up in freezer causing leakage out onto the floor. I will not purchase Maytag again. For 3 years I have fought the ice buildup and it has ruined my floor! Poor design - should have been recalled!

Gas double oven - range that has performed well over 12 years old with only one service call for thermostat. Very inexpensive to repair and parts are readily available. Easily cleaned inside and out.

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

Bought a 2400.00 refrigerator 1 year and 4 months ago. The freezer quit working and we lost everything in the freezer. We called and were out of warranty. The commercial on tv shows the bored repairman who never has any work because Maytag is so reliable. What a crock! We are going to have to pay for the labor which could be as high as 800.00. This is so wrong. This is a high end refrigerator and the fact that it only lasted a little over 1 year is unbelievable. I would dump it if I could afford to. It is a piece of junk. I will never ever buy Maytag again. Make a new commercial, one where the repairman is so busy he works 24/7. We got screwed by Maytag. They do not stand behind their product, they rob you blind.

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

I love the front loading machines. Fabrics dont get beat up like they do with a top loading machine with an agitator. My Maytag front loader doesnt have as many bells and whistles as others, but I love it nonetheless. Reliability was very important to me when I bought it, so I talked to a couple repair men to see if this was one they worked on a lot. When I found out they didnt, I bought it.

I think it would be nice to state on the box of dishwasher that customer may need a water connecting fitting and hose for their new dishwasher. Yes, I was asked if I needed anything else and I replied I dont think so! Well when I got home, I did need the water supply sweep 90 degree elbow. Or tell sales people to inform there are parts missing. I had to drive back to Huntsville, AL from Hazel Green. Not life or death, just saying! I do like Maytag products. The dishwasher I replaced was17 years old and we had good service! It’s just starting sounding like a rocket motor. Time to upgrade, I thought. Well my wife really thought so! ;)

My fiance bought this dishwasher 5 years ago but has never been able to use it due to the fact he is disabled and unable to open the door. When I moved in 4 months ago, I began using it regularly 2-3 times a week. Yesterday, I loaded it and when I hit the start button, it did nothing. The lights come on but the start button doesnt seem to be working. I have torn it apart twice and after looking all over the internet have determined that the control panel is bad. We live on a very fixed income and fixing something like this will take a large part of our budget. I am shocked that something so expensive can only last a few months then stop with no warning. We will be calling and adding our names to the list for the class action lawsuit here in California.

All I can say is, Wow. My Maytag washer and dryer have never needed anything in 21 years of service. Purchased in 1997 at Lowes in Chambersburg, PA. Both work and look like new! Both are top of the line units. Would buy again!

I bought the Maytag Bravo XL MVWB725W washing machine and dryer pair in August of 2015. 2 months after I bought the pair the thermostat went out on the dryer. It was under warranty so it was fixed and no problems after that. In July of 2016 I have my first stainless steel hose break at the fitting because of corrosion flooding my laundry room. I thought it was a fluke so I put another one. The next hose started to corrode in September 2016. We thought there was some weird chemical reaction going on between the hose and the filter on the back of the machine. So we changed to rubber hoses in September. Since then we have gone through 6 sets of rubber hoses. We have had the water company out, they say our water is fine. A plumber out, our new water heater is fine as is our plumbing. An electrician, who changed an outlet and put a grounding wire on our house water line. And an appliance repair man, he found the problem so he called Whirlpool who makes Maytag. There is corrosion on the water temp control. However nobody has EVER seen this problem and doesnt know how to fix it. Not even Whirlpool. And Whirlpool says its my house. Im at a dead end with a washer that is constantly going through hoses. It really doesnt wash clothes very well either unless you put a lot of stain remover on the clothing before and wash it in hot water. And yes it is noisy. Dont buy this product.