My dishwasher like many others have mentioned is experiencing the same control panel issues. When I set it to Wash, it spontaneously goes to Rinse Only. I am unsure exactly the age, but given the number of complaints Ive read, with the same problem, it seems as though, there was a flaw many years ago in design and regardless of issues hasnt been resolved with the newer models either. I realize appliances dont last forever, but Maytag was always known for the lonely repairmen and Id hoped the brand would continue to live up to its advertising, despite being purchased by Whirlpool.

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

I purchased a Maytag side-by-side, model MSD2656DEQ, in June 2000. First service call within a couple of months was for a very noisy ice dispenser, which the tech said was normal. Other than the noise, the dispenser has worked fine. Aug. 2005, the freezer frosted up and the tech replaced the defrost timer and defrost thermostat. May 2010, I had the same problem again and again these two parts were replaced. This morning, I found the food thawing in the freezer, 3 1/2 yrs since last repair. It is Sunday so will have to call tech tomorrow. Third repair in 13 years for a $1500 (2000 year dollars) Maytag. I have never had an appliance with so many problems and it was the most money I ever spent on an appliance. I am done buying Maytag products.

The dishes need to be washed off to be sure they will be clean. It holds a lot of dishes. You can put it on a short wash or long one. Leaves water on base of glasses sometimes. Holds moisture. Heavy wash, normal wash, light wash, rinse only, auto clean, delay 1-9, heated dry, sanitize, tough scrub, extra rinse. Regular size 24. Beige color. Electronic buttons. Maytag Quiet Series 200: I do not like the racks for putting dishes in. Otherwise it holds a lot. It does not clean dishes if you do not rinse them off first. If you run the dishwasher immediately after putting dishes in it will clean them off. Sometimes it leaves water standing. Even with what I have said I really like this dishwasher. We have had the dishwasher a long time. We use it at least 2 times a week.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

Nobody seems to know how to replace this part online. I have discovered what a POS this Maytag MGDC700VWO dryer is. The ONLY way to access this part is to beat an access hole in the bottom-left panel. After the repair, you are left with a nice 4 hole??? What an absolute POS! The back panel has screws but after removing them, I discovered the panel is also tack-welded! This is beyond stupid! Maytag used to be a great product before they were obviously sold to the Yugo factory. Time to move on.

Our Maytag refrigerator was about a year old when we noticed rust on the edge of the stainless steel doors. I called Maytag and they were nice enough to replace the doors even though the warranty had expired by their standards. Keep in mind, the warranty starts when you purchase the product, not when you install it. We ordered our appliances from Lowes well in advance of our kitchen remodel so we would have them when we needed them. The time our appliances sat in Lowes warehouse used up two months of our warranty.Now, the new stainless steel doors are rusting and they are refusing to do any thing about it. Should stainless steel rust? Maytag doesnt seem to care whether their product performs the way they should. Its all about the warranty. Once the warranty lapses, they could care less whether their product blows up. Thats the customers problem. Whatever happened to building a quality product that lasted and customers bought for generations? Obviously, thats a thing of the past.My goal in writing this is to make consumers aware of appliance warranties. When I spoke to Lucas, a Maytag customer service supervisor, he informed me their products offered no warranty on the finish of the product. So, according to Lucas, the finish on your brand new Maytag appliance could flake off like dandruff and its your problem regardless whether its a manufacturing defect or not. Remember, buyer beware!

I would like to start with, my Mother had always used Maytag washer and dryers. Her machines would last 20 years or more. I bought a Maytag front loader washer and dryer in 2006, since owning these machines have spent in upwards of $1400 in repairs. Some being flood out of tub, mother board blow out a couple of times as well as various other issues. The biggest problem is the awful smell of our clothes, I must wash clothes multiple times to try and remove these smells. I tried contacting Maytag and they dont want to hear my complaints and push me off to purchasing another washer and dryer. Oh, I will be buying a new washer and dryer it just will not be Maytag. Do yourselves a favor and DO NOT buy another Maytag. This is not the same company my Mother knew and trusted.

We upgraded and purchased a new Maytag Dishwasher Quiet Series 300 MDBH955AWQ to benefit our new kitchen remodel. Initially, the dishwasher worked great. I routinely insist on keeping the filters and interior clean as I was raised up believing that if you take care of your equipment, it will take care of you. Very shortly after purchase, there was a fire recall which was taken care of by Maytag and a third party contractor. Then as time went on, it continuously rendered out dishes with debris and food on them. Then it stopped working. It turned out the latch or door handle broke on the pivot point on the interior of the door. I got that replaced and everything was good again. Then about three months later, of course after warranty, it would not start or anything. I verified power and connections and nothing. I spent about $60 on JustAnswer for further advice and the answer was to replace the control board. After about $250 for a service call and $130 additional, it turned out the control board went out. I observed how it appeared to be a poor design due to the control board being exposed to all of the humidity and other moisture from within the dishwasher door. Then after that being fixed, about six months later, the door latch broke again. Its minor enough that you may not realize its broken until you open the door panel back up again. The plastic is breaking Im sure due to the heat and moisture, but its just minor enough that it will not make contact to indicate the door is closed. I got that replaced again for another $140. Four months of that getting fixed and Im getting the same result, no functionality at all from the control panel. In other words, the control board is out again!Ive spent almost as much in repairs that I have for the dishwasher in the first place. As many have stated before, why are we not getting quality products anymore? I went to the Maytag website to see if there were any other additional recalls for this dishwasher, and the recall site was down, so I called. The lady on the phone, as pleasant as she was, indicated that the recall for the heater coil was already performed, which I already knew. I asked, due to the other problems Ive had and money Ive spent, if there were any additional recalls, and of course the reply was no. Im used to staying with a reputable company and providing loyalty to that company for quality products and service, even if I have to spend more initially in order to spend less overall. Obviously, Maytag is now out of the question for future business or referrals. This dishwasher is getting replaced before I put one more dime into it.

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

Fire Danger. We had a power outage and my Maytag gas range/double oven (Model: MGR6875ADS) was dead after the power came back on. We figured it was the control board and braced for the expense to replace it. A few days later, I plugged the oven back in just to see if it would work and it did! The control panel came back on and we were up and running. The good news end there. On Christmas Eve, we came home to a house full of smoke with fire alarms buzzing. A butcher block style cutting board that was on top of the range with Santas cookies on it was on fire. Twenty more minutes and the house would have been gone.

Was very happy with choice when it arrived. Bought October of 2010. Now, this summer, nothing but problems. Honestly weekly cleaning of vents underneath, sheets of ice in freezer, refrigerator not staying cool, constant frost plugging areas, and no more ideas of how to make it work. I already quit with Kenmore after terrible problems with their appliances and now when Maytag doesnt stand up for years what are we supposed to buy? OUTRAGED with American quality of products and disposables. UGH!!!

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

Prior to purchase, I did my due diligence and read reviews about this washing machine. Apparently, they were written by Maytag employees, because this washing machine has been a major disappointment. Yes, it tangles clothes and sheets, but I feel that is to be expected since it is HE and uses less water. I will give it that and I dont have to dry nearly as long. But that is where my positivity ends. Clothes dont always come out totally clean. And then there is the issue with the horrific grinding noise. The machine has been making a progressively louder, angry, grinding noise with a high-pitch end note. And as of today, a horn type noise has started. Lovely.I anticipate the machine is on its last legs and I have only had it a few years. I spent too much money on this and feel like I have been misguided and, quite honestly, ripped off by Maytag.

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

Maytag Bravo X-We bought this washing machine not even 4 years (February 2013) ago from Lowes. We had this issue before the warranty went up a couple of times and then it stopped and started working fine. We contacted Maytag before... But of course beings the issue resolved there was no way to send someone out here to troubleshoot the problem. Now it is doing it all the time. A few months ago it went out of warranty. We are having issues with it going into the spin cycle and it will stop there and it will not spin out my clothes and finish draining. Contacted them and they want to charge money for a service tech to come out just to look at it. Lord only knows how much it would cost to fix.

We bought a Maytag refrigerator about 3 years and have had so much trouble. The freezer section which is on the bottom half leaks water periodically on the floor unless, we take the bottom rack out and pry the ice from the shelf about every week. It started doing this about 6 months ago and well need to get a repair man out here. The doors on the refrigerator are also a problem. They often dont close properly, so one is partially open, but unless you look directly at it, it isnt noticeable.

I purchased this washer in January 2017 at our local Home Depot here in Mexico. It was a washer/dryer combo. Now, in July, a mere 6 months and only a few wash loads later, it has gone from the worst machine I have ever owned to what I consider to be garbage material. First of all, it boasts about not using much water. This is true... Only 1/4 of your load is in the 3 inches of water at the bottom of the machine and the top 3/4 never even gets wet. I couldnt believe it. Now, I put 2 sheets in this morning and it fills almost to the point of spilling out, though I have to give it credit for shutting off the water before it actually did so. This is a NEW washing machine!!! I, along with a lot of other folks from what I am now discovering, are all in the same boat. I remember Maytag being a mark of excellence way back in the day... This is no longer the case. Stay away from this company... I know I will.

MY MAYTAG WASHER and DRYER ARE 17 YEARS OLD. THEY are FRONT LOADERS WHICH I THINK MAKE A DIFFERENCE. I BOUGHT MAYTAG because I had trouble with Whirlpool products that didnt go the test of time. The only problem I have with my washer is the mildew.

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

7 years is all I got from these appliances. The Maytag Washer started making a horrible noise when washing then smoke and shut off. Dryer would not shut off. We have taken excellent care with these appliances servicing them as we had an extended warranty on both. They cost us over $600 for the washer and $589 for the dryer, a big rip off! I purchased them in hopes I would at least get 15-20 years of service as Maytag is to be one of the best. Do not purchase any products from this company, they also have sister companies. Make sure when you need an appliance, you ask who makes them.

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

I have had this Maytag washer maybe 2yrs at most and it is junk. I am a single mom who desperately needs my washing machine. My kids clothes get soiled, they ARE kids so I wanted a deep water fill option when looking for our newest washing machine. Well when I start a load of laundry, I can hear the water running and draining as it is filling the basin. So for 1 they get wet but not washed. Then when it gets to the rinse cycle it stops so the only option is to manually switch it over to drain and spin in order to not have sopping wet clothes, however, since the water doesnt fill, they arent being washed, the rinse cycle doesnt work so the soap is left in the clothes, then I just have to drain and spin in order to get access water out so they will dry in the dryer. Its very upsetting, I have no way to buy another washer, I assumed this costly purchase would last me a while.Sadly, I have seen many negative reviews re: their product. I didnt check reviews before purchasing, I knew I needed a large basin and wanted the deep fill option. I always thought maytag was a good brand. Now I am in a jam. :( If you are looking for a new washer read the Maytag reviews before considering this brand. Live and learn. :(

We bought this washer before Christmas. I was very excited. However my clothes don’t come out clean. I am actually washing my white uniform with hands because each time I wash, dark scums remain on my clothes. I think that the machine sensor does not sense how much clothes are in there and how much water is required. This machine is very disappointing, it needs to be recalled. See pictures below.

Our current dishwasher was already installed when we purchased this house. It is adequate, however, it does not do a great job with caked-on food. This means that the worst dishes need to be pre-cleaned.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

Its the worst experience I have ever had with any product. I grew up watching the Maytag man as a child and thinking that must be a top of the line product. Boy was I wrong. I went out six years ago when I purchased my new home and purchased for 1,550.00 a brand new refrigerator with side by side, and ice maker on the bottom, silver in color. It looked great, the quality was and is terrible. The freezer stopped freezing a couple of days after the first year was up. The Service department at Maytag is terrible, I called them for assistance and they were anything but helpful rude is a better word. Its been a nightmare! How could they ruin that good, or even great name of that product. Never will I buy a Maytag appliance again. I tell all of my friends as well. Oh yes so far as the leaking is concerned, my floor is damaged as well.

Less than four years ago we purchased a new set of Maytag appliances, refrigerator, stove, dishwasher, microwave, and upright freezer. To date, the only appliance we have not had a problem with is the microwave. The bottom element is not working on our stove model # MER8775AS. We will never buy Maytag or Whirlpool products again. Save yourself time and money!

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

We purchased our washer/dryer in June 2004. I have tried to clean off the rust where the water enters, but not successful. Is there any way to have this replaced at no charge?

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

Dinner ruined again... I bought all brand new Maytag stove MERS755RAW, I can only use one area and that has cant move them, the racks fall through. I have burned myself time after time when attempting to pull the racks in or out. Friends arrived and when we pulled cooked dinner out the rack fell through and it was so hot I could not hold it causing the entire dinner to come crashing down and spilling everywhere. I along with my family cannot use it again. Can anyone assist or make a recommendation? New racks do not work as it appears that oven has expanded and the dimension have changed. Do they have a recall or safety repair bulletin?

Bravos mct. Unbelievable, this washing machine is terrible, no water. The water level doesnt even cover 6 items. Have to wash triple the loads of my old washer just to get the clothes clean. I have to go to the laundromat twice a month. I shouldnt have to do that. Almost want to fill the washer with water, but dont know what will happen. Very unsatisfied with this washer.

I waited my entire life to age 47 to purchase a brand new matching Maytag washer and dryer. I was thrilled. That was August of 2012. 3 years and two months later, the $800 dryer (MEDE201YW) loses the entire control panel and Maytag refuses to offer any assistance. I deliberately purchase Maytag with its stellar reputation, an American based company only to be more disappointed in the product and the company than in any other appliance Ive ever purchased.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

The big problem is Lowes and Home Dopey, I mean Depot. I am an appliance repairman for 30 years. Their machines are built to a lower spec. Buying same machine from mom n pop store will help! Will cost you more but it will last longer with less repairs! P.S., While Maytag does make some of their own appliances, when Whirlpool bought Maytag years ago they shut down the Newton, Iowa plant. Whirlpool builds that washer and puts Maytags name on it. If you want a good washer buy a Speed Queen, go online and check their reviews! One more thing, LG and Samsung build terrible appliances. Do yourself a favor and stay away from them, just saying!

We purchased a Maytag Gemini with serial number D40941338 and model number MGR6875AD826. It has been a complete disaster. The control panel keeps breaking down, and its now going to be replaced for the 6th time. I have asked for a new stove when I called the Maytag Extended Warranty Department, and they will not replace this defective product. Please help me.

I purchased a Maytag dishwasher in Jan 2012 at Home Depot. It ran fine for 1 and 1/2 years and was only used 2-3 times per week. I returned from vacation and now needs a new control board at a cost of $300. I felt Maytag was a reputable company and am very disappointed. I am a senior and on fixed income and now sorry I chose a Maytag. I will get it fixed this time but that is the last money I will invest in Maytag appliances and repairs. I worry that the washer and dryer will go next as they are also Maytag and are just over 1 yr old.

Purchased the Bravos XL top load washer a month ago. We work outside daily and our clothes get very dirty. I havent really taxed the machine yet (Im doing what I consider a normal load of wash. I know the machine could handle twice as many clothes as its the 5.3 cubic feet washer, but I havent had that many clothes to put in at one time). The washer works great. Clothes are clean and smell fresh. For those that say this washer is extremely loud - you must not have something set up incorrectly. Either the wet pan you put under the machine is making contact with parts it shouldnt or someone didnt level it properly. Really, this is NOT a loud machine. We purchased from Lowes and they delivered, set up and leveled both the washer and dryer. (Yes, we also purchased the matching Bravos XL front load dryer and were impressed that it dries our clothes in half the time our old one did). We would definitely recommend the Maytag Bravos XL washer and dryer.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

My husband and I bought a Maytag Bravos HE washing machine 3 years ago at Home Depot. It is by far the WORST appliance purchase we have ever made in 40 years! This machine started making horrible grinding noises about 6 months. It is not rinsing properly and its leaving detergent stains on our clothing. This washer needs to be recalled. I will NEVER buy another Maytag product, EVER!

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

We purchased this washer from Sears. Its always been loud during spin, but the past couple months it has gotten VERY loud. It jumps around. Also, it tends to ball clothing and towels. It has been hard on my clothes and bedding. Many times I have to rewash towels and bedding, even jeans at times. I have been very unhappy with this purchase from day 1. It was not a cheap washer.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

I bought a Maytag MMV1153BAW Microwave. Within a year, the electronic key pad started cracking from normal use. After two years, the microwave intermittently starts then just stops, with the key pad showing 0000. We must unplug the device, or turn the breaker off and on. I called Maytag about the key pad and they said it wasnt covered, and a replacement key pad cost more than the microwave. After two and a half years, we purchased a new microwave, and have sworn never to buy Maytag again.

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

I bought the Maytag Bravo XL washer and dryer at Lowe’s on sale spending almost $2000. Loved both of them until the washer stopped with a load of laundry in it. No power to unit. Called for service. Could not provide serial number as locked in washer. Service company able to order parts without the serial number but part put on back order. Washer needs a master board. After 1 week of wet laundry stuck in the washer called store manager at Lowe’s. I contacted Maytag Service and had a rude customer service clerk who finally listened to me after I got angry with her. She contacted the appliance repair company and got the back ordered part sent to the appliance repair company. We are now 10 days out. Still do not have the part; just talked to appliance repair company supervisor. The appliance repair company supervisor said he would schedule installation as soon as he had the part. It will probably be 14 days when I get the washer fixed. I am dreading opening the washer to get the load out that I will have to throw away. When I called for service at Lowe’s the representative said, We have had a lot of issues with this. A 2 month old new washer should not have the control board go out. Shame on Maytag.

Bought brand new. No deal, not on sale, not a return. Just heres money... give me working washer. This thing doesnt wash anything. It leaves soap all over the clothes. When you turn it on and wait til it starts washing, look in there with the lid open... theres barely any water! The clothes on top stay dry! The only way to wash your clothes in it is to add three-3 gallon buckets of water at the start of each STAGE of EACH cycle! My wife showed me after three months of washing clothes like this. Anyway, to the garbage with this and back to Whirlpool basics with me.

On 8/26/16, we purchased a top-of-the-line Maytag dishwasher from Lowes of Palm Bay, Fl. It began leaking water out one side shortly after installation. Because of a hospitalization, we were not able to report the problem to Lowes until the first part of December. A repairman from Brandts in Sebastian, Fl. came out on 12/6/16 and said it might be the door gasket, but he did not have a new one with him and if it continued, to call back. I called again and another repairman from Brandts came out on 1/3/17. He said it was out of square and he took out 2 screws and said to cut back on detergent because too many suds could cause it to leak (which we find ludicrous). Now it leaks on both sides. This is not a small leak; it soaks the bath towel we put under the door. On 1/11/17 Brandts sent 2 repairmen out and they claimed we needed to cut way back on detergent and put in a capful of salad oil because our water softener is causing the suds which causes the leak. We now use 1/2 teaspoon of detergent and the capful of salad oil. It is still leaking. Our previous Kitchen Aid dishwasher never leaked and we used the recommended amount of detergent in it. We are apparently stuck with a brand-new dishwasher that cannot be fixed. We will NEVER buy another Maytag appliance.

I can’t seem to get any help with my dryer. I have replaced the drum 2 times and thermostat 3 times. Model number is mde9700ayw. Serial number is 13229569gp. I simply want a new dryer that works.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

The best we can tell, we got our Maytag in 1991. This was because the repairman told us that was the last year they made parts for it. It ran wonderfully until 2018. The water valve broke, but a repairman easily fixed it. In 2019, it stopped running. The repairman fixed it, temporarily, he said. He refused to charge us for his work because he said we might get a few more loads done before it completely pooped out. Were still using it. I love this machine. It has gone WAY past the expected life span of a washing machine. Weve had it for 29 years!

Purchased new Maytag MF 2558 VEM5 for over $1000 and have had nothing but problems. Water constantly leaking on floor, ruining kitchen wall trim. Now ice maker doesnt work. Bought in 2011 and started leaking after 2012 on out of Warranty. Now in 2014 ice maker stopped working. Bought at Home Depot who refused to fix. The worse fridge I have ever had.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

I purchased my first Maytag (Bravo Washer) appliance in 2013 and thought this washer would last me for a minimum of 10 years. It started making noises occasionally right away but I wasnt too concerned until it started sounding like someone was banging on it with a sledge hammer. I waited 8 days for a repairman who told me the bearings were going out and it would cost $400-500 to repair. This is the worst washing machine ever manufactured. My advice is to buy any other brand. Dont be fooled by the Maytag hype. Their quality is nonexistent. I am shopping for a new washer.

We replaced a 20 year old Kenmore washer with this Centennial washer (MVWC360AW), and after 2 years we are looking for another washer. The machine will not complete the wash cycle, and when we called for service, the factory authorized service tech couldnt figure out what was wrong with it. After 2 service visits in a months time, I tried contacting the company directly with my story to see if they would help resolve the issue. I sent them a letter by mail as well as on their contact us link on the company website. They have not responded to me in any form. We will never purchase another Maytag product, and will tell everyone we can how terrible this machine is and how the company apparently doesnt even care.

Me and my wife bought a Maytag refrigerator from Home Depot. The top half freezes up in a big way and it gets real frosted up I have to pull it apart every 2 months to defrost it. The bottom half starts to get warm if I dont do that. I will not ever buy another Maytag refrigerator again.

I, like SO many other people, am experiencing problems with a relatively new Maytag dishwasher. Mine is Model MDBH979SAB1. I have owned the dishwasher for 4 years but use it 6 months of the year and, because I live alone, maybe twice a week. In effect, it has the equivalent of less than a year of normal use. My problem is the same as countless other people. I can tell from how it behaves that it needs a new control board. I find little comfort in the fact that I one of several thousand people experiencing a problem with a newer Maytag appliance. What concerns me, after reading many negative reviews and seeing Maytags response, is that Maytag does not seem to care. We need to get the word out. We need a massive boycott of Maytag. We need to hit them where it hurts: in their bottom line. Since they seem to be content to continue to put out defective products, the only way to protect consumers is to put Maytag out of business.

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

I was told to at first to just leave the door open, then when that did not work I was told that I should bleach my machine at least once a week which I did. That did not work either. Then I was told to buy the product REFRESH and that would take care of the smell. That did not work either. So I am at my wits end with the stench of my clothes.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

I purchased this $900 Maytag washer from Home Depot in Oct. 2010. Now, after Ive just paid $129 for a service call through their designated repair service, I was informed it will cost $700 to fix this washer. I use the washer on average of three times a week. Its unbelievable that this type of crap is sold by Home Depot and that Maytag warranties will not cover repair as one year has passed.

Purchased my Maytag Bravo MVWX500XWO 4 years ago. While still under warranty I had to call for service once. I felt based on the Maytag reputation I didnt need to extend the warranty. WRONG!! My Maytag first started with the loud and fast spinning. Like it was about to explode! Then my washer started leaking. I thought I was having plumbing problems, so I called a plumber... wasnt the plumbing. My washer wasnt draining out completely so I finally called an appliance repairmen who immediately knew what the problem was ($109.90) for a 15 minute review. The leak was from the bottom of the washer... the seal around the transmission cracked, broke or whatever causing water to drain out in my garage. Also the main control board wasnt working. Repairman said it would cost me $700 to repair!! Really?!! My machine was practically new! Without hesitation the repairman said for me to call the Whirlpool/Maytag 800 number and they would offer me another washer for 50% off at their online outlet. Repairman said this always happens... Why would I want another Maytag or Whirlpool!! Please do not buy the Maytag Bravo... Can you imagine if this happened with a car purchased... 4 years and then having to buy another car??!! Not reliable or worth your money!!

I have had this dishwasher less than 2 years, Maytag model # MDB7749SBM2. The control panel started acting up, it would not let me select a wash cycle, it would select its own and I could not change it. After reading these reviews, I took off the control panel and discovered the wires which are encased in a plastic were all darkened and messed up. I will try to replace it on my own but if I have to I will buy another brand as this dishwasher hasnt really cleaned my dishes all that well to begin with.

I purchased and installed a high end MAYTAG above the stove microwave. After 3 years of light use I hear an electric cracking sound and it dies. Of course no warranty coverage. Model MMV5208WB-1. I have to conclude MAYTAG builds junk and does not stand behind what they sell.

Bravo Series Washer and Dryer. I hate, hate, hate this washer and dryer. I have had it for 2 years and hate it more every day. What makes is worse is the over $2,000 spent to buy this piece of crap technology. The engineer should be fired and sham on Maytag for selling such a piece of crap. Washer does not get clothes clean and I have pictures to prove the amount of dirt and lint and soap left on clothes and bedding. Very poor design, and worse yet absolutely horrible engineering.To wash one item on delicate takes 47 minutes. No way around it and you are limited to the water temperature you want to use and the spin cycle that you want for that item. Water level is too low no matter what setting you use. I have read and reread and gone step by step according to instructions with no success of clothes coming out clean. Clothes are also twisted and knotted and wrinkled like no other machine I have used in over 50 years. The washer is very limited in what it allows you to do. Bedding cycle is a joke that does not work at all. One of the reasons I bought this was so that I would no longer have to take the time to drive to a laundromat. I washed a comforter and so much soap and lint and dirt was left on the comforter. I still had to take it to the laundromat to get it clean.Dryer is just as bad. Even with the energy saver off it still takes 1 hour and 20 minutes to dry 4 towels that are 5 years old. I cant imagine how long it would take to dry brand new fluffy towels. It was engineered to sense when ONE piece of clothing is dry. I want ALL my clothes dry, not one piece and the machine shut off. How stupid is that??? Engineers - design it so it senses when clothes are still damp and the machine keeps running!!! I can only use the time dry setting because no other setting even comes close to getting the clothes dry.To top off the hatred of this machine some damn engineer apparently thought this was a car and needed to be aerodynamic with a curved lid on both washer and dryer so you cannot put anything on top of the machine!!! Not every house is 5,000 square feet with plenty of room and storage!!! They want to force you to buy the drawers to put underneath and then the washer becomes too tall for short people to reach down into to get the clothes out. There is not one positive thing I can say about the washer and on top of it I will never purchase another item from the store I bought this set from. I have had service come out time and time again and they say it is an installation problem. Installation says it is service and yet no one will admit it is just a very poorly designed machine. Do not buy this brand or series of washer and dryers. This series deserves a minus and the company should replace every set sold!!!

Had a Maytag washer, 3.5 tub, stopped working. The motor upper bearing lost it press, drive shaft dropped 3/4 inch and locked against lower housing, stripped out pump spline. No f/u by Maytag after many attempts. This is a design flaw, the upper housing is so thin, if it had .001 press on it I would be surprised. This flaw resulted in a cascade failure of motor and pump.

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

I have a self cleaning Maytag electric stove. I discovered the self cleaning starts after so many times of using the oven. But the stove didnt give me warning of this when I put my Thanksgiving turkey in the oven. Halfway through cooking, the oven door locked and went into cleaning mode which scorched my turkey and could have possibly caused a house fire. Also, my top burners have a mind of their own, while cooking they turn up on their own. This stove is very dangerous.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

I purchased my Maytag double oven (MEW6627DDB) in November 2008. In January 2013, with a setting on 375, it heated to 440 in 15 minutes. The repairman said $650 because it needs a new control panel and 2 new sensors, one for each oven. I contacted Maytag as I felt this oven should not have gone out in 4 years. I spoke with Ebony and then a supervisor, Vana. Basically, I was told that since I didnt purchase an extended warranty, there was nothing they could do. While I have a freezer 40 years old and still going strong, I realize that appliances manufactured many years ago were much more reliable. I feel that Maytag should stand behind their products and should have offered to send me replacement parts. I know I would have had to pay labor for installation. Their answer was I should have purchased the extended warranty. However, one should not have to purchase extended warranties for products. I had every confidence in Maytag. Why else would I have purchased my first Maytag product? I should have stuck with Whirlpool, which I was recently told, now owns Maytag. Maytag customer service personnel were extremely unhelpful. I wonder how many Maytag employees purchase extended warranties for their appliances or if theyre smart enough not to buy Maytag.

We have had our side by side Kenmore for years and it hasnt let us down! We eat mostly fresh food since we cook a lot and we always have plenty of space for our food. We are only a family of 2 though. They say the ice maker is the first to fail and it has not given us any issues for nearly 10 years now! Love Kenmore!

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

We spent over $1,200 on a Maytag washer on 12/2015 and it did not work properly. The door got locked, had a couple loads moldy because we could not get it open. Didnt drain either. Maytag had someone come look at it 3 times and it still didnt work. Called Maytag and now they told me that they cant do anything about it because is not under their 1 year guarantee. And of course they are very sorry for my unfortunate inconvenience. I thought they had a good honest reputation but... Im just disappointed!

We purchased the Bravos XL in May 2017.. It quit working on April 30, 2019. Maytag sent me a form letter that basically said I was out of luck.. that sometimes things go wrong with a product or manufacturing. The fact that it wasnt 2 years old yet meant nothing to them. I would like to join or start a class action. This washer should not be sold.

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

I have a Maytag Bravos XL and have white residue on all the clothes that get washed in this machine since I purchased it. I have always used HE Detergent and have followed all Maytags recommendations to reduce the white residue to no avail. I had to wash my clothes 5 times to get the residue off of my clothing and 4 of those were without any detergent and on all temperatures and wash cycles. Model # MVWB835DW.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.