Bought brand new coin op washer and dryer. Washer had problem from day one. Took in for repair. Maytag warranty covered parts, no labor. Cost me $100.00 on brand new $900.00 washer. Last money they will ever see from me.

I have had KitchenAid and Whirlpool my whole life - lots of them - NEVER EVER have I had so much trouble with a washer. This front loader is the worst possible machine. My former Whirlpool was a front loader too - Never a problem. I purchased this Maytag set simply to have a matched set because our Whirlpool dryer died. This washer has to be babysat. The washer holds water and it gets musty - never ever before have I had this problem. Maytag says it is designed this way and I have to continue to buy AFFRESH (which is also very expensive). I have to use this two to three times a week and the pkg says once every 6 months - DONT DONT BUY MAYTAG. LOUSY.

In July 2001 my husband and I purchased a 6-year old home. We are still here. We have replaced the refrigerator, oven and microwave - all in stainless steel. I am still waiting for the Maytag dishwasher to wear out. It has never been repaired because it has never broken down. Cleans dishes and silverware great.

Nothing wrong with this dishwasher, a bit noisy, but it gets the dishes clean and thats whats important. This was a builder grade installation and it came with the house so I cant really say its the exact model I would have selected had I been given the opportunity to pick my own.

We have had this machine for too long. It starts banging and making tremendous amounts of noise. We have balanced it and tried loading it in different ways but when it starts to spin it apparently tries to even the load somehow that results in very loud noises and movement of the washer in the laundry room. Terrible machine. If we could afford it we would trash this one in a heartbeat and buy a different brand.

My experience over the past 2 years with my top loading Maytag washer is echoed in almost every review here. 1. Not enough water to clean the clothes 2. Clothes come out still dirty and covered with detergent 3. Barely agitates 4. Repeated repairs for leaking and computer board breakdown 5. Complete lack of interest by either Lowe’s and Maytag when contacted. I could write a long, detailed complaint but it has all been said quite well. We need to band together and file a class action lawsuit against Maytag. Any lawyers out there willing to take this on?

I have always thought of Maytag being the quality manufacturer of appliance products. We purchased a Maytag microwave (MMV4205DH-1) and after just two years it has begun to give us grief (we are in our early 70s, no family at home, so appliance receives medium usage). We constantly get the open/door message when we are trying to set the timer for operation. We open and close, open and close, etc. Just yesterday my wife noticed a slight crack on the door just below the handle, most likely due to frequent open and closing. Went online and read a number of reviews and found many others have had same or similar issues. Done with Maytag.

We purchased this microwave in Jan. 2012 to accompany a Maytag double oven for our kitchen remodel. Last night while using the microwave, 2 sparks shot up out of the top of the microwave and an electrical surge noise. I quickly un-plugged the appliance. The next day I attempted to use the microwave again and dense electrical smelling smoke poured from the top of the microwave, again un-plugged the machine. I have called an appliance repairman since the 1 year warranty is up. This machine is not even 2 years old and we will never again purchase a Maytag product. PS If the problem is the magnetron (whatever that is) I will contact Maytag for the warranty information.

I bought a Maytag dishwasher, when I bought my house (7/2010). I live alone and I use my dishwasher only once a week or once every two weeks. After 3 years of working perfect, it stopped working. I had someone come look at it. After troubleshooting with the basic steps, making sure the water was correctly hooked up, a fuse was not the problem. The dishwasher door was shut completely. He took the racks and all movable parts, & thought something, a piece of glass, etc, was stuck in the drain. Nope. After reading these reviews I realize it is got to be the control panel because the start button will not come on and all these people have the similar problem. It just stopped. Period. The panel lights come on, but not the stop button. I am a single person as stated and on disability and on a very tight budget. I bought a Maytag because of the name and reputation. How long would it have lasted under normal use, say a family of 4, using it nightly? Certainly less than a year. I have no idea what to do now. I cannot afford a repairman, & I am certain it is the control panel on the dishwasher. I do of course have all the model numbers, etc & papers, when I bought it. I can provide proper paperwork, when contacted.

My husband and I purchased both a Maytag washer MVWX655DW1 and dryer MEDX655DW1 less than 3 years ago from Sears. We had both the washer and dryer professionally installed. Yesterday, we had an authorized service man come in and look at the problems we were having. He told us our Maytag washer would need a new gear case and gears costing $750.Our Dryer, same age, needed a new cycling thermostat. He said it was due to not cleaning out the lint trap. My husband and clean the lint trap after every load religiously. He said there was a pile of lint built up in the dryer. I could only think this would be a design flaw. To repair the dryer it would cost $350. The grand total to repair our Maytag Washer and Dryers would be $1100. We paid $1082.38 at Sears for both. The only thing Maytag offered to cover was a part for the washer which would cost $640 and we would need to pay the extra $110 for service in addition the $150 diagnostic charge, due to use being out of our one year warranty.We decided to not fix this machine to avoid similar problems in the future. I talked to customer service and asked them to cover the diagnostic charge instead of sending the part, which is far more costly. I got the runaround and 3 rejections before they finally agreed to pay for the diagnostic charge. My husband and I are extremely disappointed in this experience. We currently own a Maytag Microwave and Electric Glass Top Range. We will never buy Maytag again. Our Stove is also lacking. We have the AquaLift cleaning stove. The AquaLift technology does not work.

As all the other reviews day 1 Dryer had no heat, washer unbalanced and knotting all the clothes. Sent out new dryer after trying to fix to no avail. One month after new dryer, normal cycle continues to run and not turn off. Repairs again - new computer board. Now washer is winding high pitch noise level - repair new bearings. Thank goodness for warranty. But washer and dryer act up again. I purchased extended warranty. Washer tub needed replacing because transmission went out, dryer again control panel problems. Last night the dryer started on FIRE. I’m sure because the control panel normal was not working again after it was replaced less than 2 yrs ago. Total time owned 6 miserable years. Going back to basics, ugh....

We 19 years and gently used. The door latch broke. We purchased a used quiet series Maytag dishwasher and found that the door latch failed on this. I recently found over 600 complaints for the same problem. If you are receiving this many complaints and its one of your most frequent complaint, do you think its time for a redesign of the door latch mechanic is??? Or are you relying on your reputation and dont care about quality anymore?This is it for Maytag. Im glad we didnt buy a new Maytag because we would be stuck again with a crappy door latch. If you cant be bothered with fixing your door latch issues and you know that you have a long term problem here, you at least can send a new door handle kit to those of us who are complaining. Of course you wont do that. And the only recourse I have as a consumer is to tell others about the ongoing problem with your front door latch on my social media. Sadly, you are now only another crappy dishwasher with no real quality control. I bought several appliances from you because of your reputation for appliances that last. Seems that is now a myth.

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

I spent over 2000 on a Maytag refrigerator. In less than 5 years, the coolant system has gone out twice! The only response I get is, “We are sorry, but it is 5 years old.” Are you kidding me? I have a 20-year-old fridge in the garage that is still working and I didnt spend over $2k on it! I thought Maytag was the best product out there and it certainly is not. Do not ever buy Maytag.

We purchased a Maytag stainless steel French door refrigerator from Home Depot in 2011. The thermostat control (a circuit board made in China) broke and was replaced in 2012 by a certified repair person. He reminded me to dust underneath regularly, which Ive done. A couple of weeks ago I noticed some darkening of my wood floor to the left of the refrigerator and so I pulled it out from the wall a bit. What I saw was that my entire floor was wet and falling apart under the left side and when I looked into the freezer, I pulled out the bottom basket and the bottom was covered in about an inch of ice.I called, posted on Facebook and was put on hold several times for as long as 20 minutes before I hung up. I called Home Depot and asked them to intervene and speak to a rep from Maytag. I have heard nothing. There is black mold in the corner of my kitchen and a soaked floor that may go way beyond. I googled the leak and apparently this is very common with Maytag French Door refrigerators. I have a meeting with an attorney. Getting through to Maytag is seemingly impossible unless you have hours to wait on the phone. We have been getting sick for months and not knowing the cause.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

After 6 months of use, I still HATE my Maytag washer. I will never buy Maytag again! The machine must be tricked into adding additional water to wash. It begins to agitate with very little water! Destroying my clothes! Also, I am having to hand wash all my underpants. They do not come out clean. If I could send it back, I would! Feel totally ripped off! I would give 0 stars, if I could!

My Maytag dishwasher is 1.5 years old and wont start. The Maytag call center said they couldnt help me except to sell me a service warranty for $269. Then she wanted to argue with me when I asked her to pass on my dissatisfaction with their products to her supervisor. I thought Maytag was a good product. For what I pay for parts and labor, I can get a new dishwasher. She said do I expect not to have any problems with that dishwasher. I will never buy anything Maytag again. They do not stand behind their products. Plus, it sounds like many people have had the same problem with their Maytag dishwasher. This part is defective. (I am assuming it is a control panel problem.) Since corporations are people now is there someone I push into my dishwasher so they will fix it. LOL.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

We bought a Model MDB7749AWB2 dishwasher 3 years ago. The first year the panel went out one week after the warranty wore off. They replaced it then and now two years, here we go again. Dont replace the part. I am not ever buying another Maytag again.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

I bought Tapan gas stove last year, but all your ranges have a problem. Whenever we clean the range, it never goes straight stay up ,even when I bought from Lowes Store and I told them they said that defect from manufacturer. You have to correct your manufacturers defect, I want an answer as soon as possible. Thank you.

We purchased our double free standing gas range about 6 years ago. Our top oven went out about 4 years after purchase. We purchased the extended warranty from Sears and it was fixed at no charge. About a year later, the top oven would not work again. We called Sears, our warranty was up so it would be a repair that we would have to pay for. We decided to go with the Maytag repair service since it is a Maytag appliance and we had to pay anyway. The repairman came in and said that the top box that holds the electronic in it had fried wires and it would have to be replaced. So for $480, he could replace it. It was more than likely caused by a power surge. I just read that this also coincidentally happened to someone else so I find this cause to ask more questions. I also note that the top of the oven behind the burners where there is some sort of vent gets extremely hot (I accidentally touched it and had a blister the next day) when the oven is being operated. This is directly under the box that holds the electronic components. I would think that may have something to do with the wires frying since it is that hot directly below the panel. Could this be a defect in the building of the stove? Has anyone else had this instance beside the one person that I read about on your website?

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

On December 22, 2013 I purchased a Maytag front loading washer Model # MHWEE201YW00 from The Home Depot. On July 28 the bearing failed and greased my clothes and rendered the washer unusable. On August 1st I contacted the Maytag Customer Service Line; the wait for contact was approximately 20 minutes, not a very good answer time and unfortunately the best I would receive during this process. Despite the wait, I received good response and had a service call set up for Wednesday August 6th.On Wednesday August 6th, a service technician from Quaker City Appliances took a look at our washer and determined that the bearings had failed and that the entire drum assembly would need to be replaced. He stated that anytime the bearings fail this soon, it typically means that the bearings weren’t pressed properly or the drum wasn’t tightened enough and that he would order the parts as soon as he got back to the office.On Friday August 8th, a representative from Quaker City Appliances called and notified us that the part was no longer available and instructed my wife to call Whirlpool Customer Service and give them this number **, to coordinate a replacement washer. I called later that afternoon and spent over an hour waiting and was transferred between departments. The first representative was very cordial and professional; the second who I believe was from the Tech-line was anything but. In my career I have held responsibility for customer service and while there are many golden rules, one of the most important was never to tell the customer “I can’t”, well Cheyenne (I believe that was her name) couldn’t help me with anything and clearly told me so. She explained that my problem was referred to the Trade Partners and I needed to call back to Quaker City Appliances on Monday.On Monday August 11th, I called Quaker City Appliances, who promptly informed me that the matter was turned over to Whirlpool and I need to contact them as there was nothing else that could be done. Later that day I called back to customer service, again waiting between two representatives at least an hour. I was informed that my matter was with the Trade Partners and that I will need to wait one to two days for a phone call. A phone call that never came…..Yesterday August 14th, I contacted Whirlpool customer service, again waiting over twenty-five minutes for the first contact, and then was eventually handed over to the tech line and another wait. Eventually, I spoke to a very pleasant representative who gave me the Trade Partner number and transferred me, unfortunately I was disconnected. I called back and found out that the office closed at 5:00. Today I called the Trade Partner line (1-800-874-4698) at about 3:30 and after 40 minutes I have given up and decided to write this letter. All I want is a functioning washing machine.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

I purchased an expensive front-load washer and dryer a few years ago. About a year after I purchased the washer, there was a foul smell that developed. I contacted Maytag and they informed me of the directions to follow - keep the washer door open when not in use and use Affresh tablets periodically. I followed these directions and was unable to prevent the washer from developing mold in the washer. Id like to file a formal complaint on my washer and dryer. I want a refund on it. I paid way too much money on these units to suffer. Here are the details on my units: Maytag 5000 Series with steam 4.5 cu.ft., Maytag Commercial Technology, Model: MHWE550WW01, Serial: CS00202582, Type: 199-02 732 WT/CR, 12 amps, 120 volts, 60 hz.

I purchased my which I thought was a stainless steel French door refrigerator in 2011 that I was getting a great product. Not even 3 months later I was using my warranty to stop the leak from my freezer now. Mind you, I paid $1500 so I got it fixed. 3 months later I called for repair again... Getting annoyed because this time the freezer came off track. 6 months later were chopping ice chunks up to stop the leaking on the floor. This lasted until last October keeping towels and old clothes around the fridge to soak up the water. This is so embarrassing especially if you have company over. You have a pile of crap soaking up water. I am a wife and mother of 7 children. I cant afford to just go buy another fridge. This isnt fair... I spent hard earned money on that magnet attracting stainless steel fridge and Maytag could care less. Im so disappointed and broke. Now I have to scrap it.

We bought a brand new Maytag refrigerator online model # MSD2660KES and it arrived dead. The first Maytag tech that was sent said he does not recommend us fixing the problem because refrigerant leaking will happen every few years. We were not able to return the refrigerator, so we opted to let Maytag fix it. Here we are 2 years later and sure enough, the refrigerator has stopped cooling. We are out of warranty period, so the service call cost us $65.00. The tech told us this time its the compressor and replacement would cost $650.00 to fix. We are not wasting any more money on this piece of junk.

I purchased a Maytag gas range in the past few weeks with Aqua Lift Cleaning System. I have only cooked once when grease spattered on the walls and floor of the oven. I have used the Aqua Lift Cleaning System 5 (five!) times and the grease is still there and very sticky. This system clearly does not do what it was supposed to do. I was fortunate to have bought the appliance where I could return it; however, it has been quite a hassle and I will have to pay an additional $100 to have the old one removed and the new one installed! I feel like Maytag should reimburse me the $100 because it is obvious to me now that I have found hundreds of reports of people not being satisfied with this feature.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

On May 23, 2009, I purchased a Maytag bottom mount refrigerator even though I knew that Maytag had many problems with this product and others. I innocently thought that by the year 2009, all their problems would have been taken care of - I was wrong. On April 2, 2011, the freezer part of the refrigerator was not defrosting. I had to make a service call to replace the control board. On March 3, 2013, the regular part of the refrigerator was not cooling. I had to make a service call to replace the control board.Complaining to Whirlpool is a waste of time. The best answer I have received is, I am sorry. There is no end to the garbage Whirlpool is manufacturing and by my experience they dont care. Why dont we, the consumers, hire a lawyer and start a class action suit to let Whirlpool know we are fed up with being ripped off?

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

I have owned my Maytag Neptune Washer since 1998 and this is the first time that it will not drain all the water... Doing some research before I call a repairman... Have a Great day!

Bought the Maytag top load high efficiency washer (also matching dryer which works perfectly) brand new less than 6 months ago. It is the worst. It leaves swirl marks on my clothes that doesnt come out. Leaves part of clothing dry without being a large load! If I put sheets in there it blows up like a mushroom and leaves that part dry. I use the correct detergent. I had a serviceman, that the manufacturer suggested, check it and determined there is nothing wrong with it which only leads me to the conclusion that it is a poorly designed product. Spoke to a manager at Maytag that said the machine works fine. And because it is in a business setting there is nothing they can do. (What? If it worked fine, I wouldnt be here.) Called to company I bought it from... Theres nothing wrong with the machine plus we are closing the business so its the manufacturer warranty that you need to call them. I would have been happy with a exchange. Poor design, poor customer service.

The control board is not working on my 2 year old dishwasher. I now see this is a common problem with Maytag dishwashers. I have called to see if there is a recall on this problem and they said no. I have been told it can cost up to $500 to fix it so I guess it is a throwaway. I should have called when it was purchased as the digital buttons didnt seem right from new. What a waste of money and I will never buy Maytag or Whirlpool.

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

I bought a Maytag dishwasher from Home Depot August 2018 and it has leaked soapy water every 3 out of 5 times that I run it. Home Depot said they dont cover installs after 2 weeks and to directly contact the manufacturer for service. Maytag sent out a tech 3 times but they werent able to replicate the problem, so nothing has been done to fix the dishwasher even though Ive shown the tech different photos of the dishwasher leaking. The service tech said they will now charge me $90 to return, even though the dishwasher is still under warranty and not repaired! Ive owned many different dishwashers (rentals and houses) without any problems. This is the first Maytag brand and it is horrible. I will never buy another Maytag and have warned all of my friends and family.

I purchased this at Home Depot October 2013. The oven heats well. I like the upper and lower oven feature. The broiler works fine. I rarely cook using convection. The self-cleaning feature, to this date works fine. Dislikes - the stainless is cheesy and scratches easily. The knobs on the front are of poor quality and the cook top stains easily and does not come clean. Disturbing - the gas cook top has come on twice with simple bumps and gone unnoticed for a period of time. Usually, you hear the clicking with the gas turning on, but not always. MOST DISTURBING - last night, 1:30 in the morning, I wake up to the heavy smell of gas. Neither my husband, nor I cooked that day, at all. I walked out to the kitchen (opening windows along the way) and the right front burner knob was turned just enough to expel gas, no clicking noise, no flame. This being the third incident (that I can recall), I think this appliance should be recalled. The knobs are not secure/safe enough to be on a gas appliance. Aside from the hazard described above, I too am dismayed at the fact that drips go between the glass and there is no way to clean it. Another poor design flaw.

Ive had my washer for about two years and have been disappointed from the get-go. I did a lot of research and found this to be top rated... Wrong! Even though I use the HE detergent and Ive even cut down the amount with no results, it leaves gobs of soap/lint residue on most of my darks and I wind up having to either rewash on clear or rinse by hand to get rid of the stuff.Ive also noticed some snagging on some brand new towels, but I attributed that to possibly the brand. Well, then I had an issue with some very expensive bottom sheets shredding and raveling and still didnt catch on. Today I noticed a different towel with similar problems, which led me here and walah! I see Im not the only one having these issues… Darn! Warranty is expired and Im stuck!

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

My husband and I purchased a brand new Maytag dryer in January 2012. Our first issue came when the sensors went out in March; then the belt slipped off the drum in June; then the thermistor was defective in July; and now, the same thermistor code has popped up twice since replacing it. I cannot afford to go to the Laundromat all the time thats why we bought a new dryer. Please give me a refund so that I may buy a different brand. Model number: MGDB850WR0, Serial #: M10301051

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

Pleased with all the features. I have had zero problems with this Maytag refrigerator; no problems with the ice maker; the crisper works well. The adjustable shelves are so convenient.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

One time at around yr 2 of our 10 yr warranty the repair guy removed my agitator, spline gone. Couldn’t find one anywhere! After a month of using a laundromat, I called the company in Montreal and they had the new agitator in my post office in 4 days. I am unable to wash anything that puts the Bravo washer out of balance ie: towels. The sides are busting out on the machine!! We have only had it 4 years so far. Not impressed! Does the warranty cover busting out sides? As it is a major part of the structure of the machine.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

We have a Maytag Neptune washer we purchased new in 2001. The Neptune was useless on My mechanic clothes, but good for delicates and blankets so we have an old style washer to clean my regular clothes. The Neptune was at work on a blanket when we smelled it burning. With it unplugged, I got around to investigating the situation and found the motor control was shorted and burned. I tried calling Maytag. I was asking about an upgraded part or recall. They didnt want to help. The representative was condescending and after I listened to her attitude, she said someone would be in touch. NOTHING. Now I see these suits and I guess I understand. My house could have burned down - they dont care. Maytag is garbage and Im sorry I ever thought otherwise.

We too bought a Maytag range (MER5755QAW) approximately 5 years ago. While making Christmas dinner, it quit working. The oven would not heat. Too bad it had to quit that day (or at all for that matter). Unfortunately, every single appliance I bought for my house 5 years ago is a Maytag appliance! The microwave quit last month and I have yet to replace it. I bought Maytag because for the longest time it was such a positive household brand name. Unfortunately, with 2 appliances less than 5 years old and out of warranty, I will never purchase one of their products again! I will spend the extra money and go with LG especially after reading some of the reviews on here on Maytag’s products (there are over 192 complaints on the Maytag ranges and ovens alone on this one forum).

I purchased this washing machine from Home Depot in 2012. I am amazed that it lasted this long after reading the reviews on here. It will not drain water, it will not spin. I see many customers bought the same washer and are having multiple issues. When will Maytag recall these machines? Overpriced and unfair to consumers to sell something that is broken or not reliable.

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

My Maytag has been out of service more than in service and this is my 2nd one in 2 years. They replaced my first one due to breaking down several times. I have spent so much $$ at the laundromat after paying big bucks for a washer.

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

My old Maytag is still working after 20 years but my husband surprised me with a new pair! Washers is just pure junk. Not enough water to hardly wet the clothes. They just rub together and get worn out looking, towels are rough and not soft but my biggest complaint is the AWFUL wrinkles! I have to iron everything! Only had it 3 days, called Menards and asked if we could return for an exchange or upgrade and they said no. If this is the best American Made has to offer, then I will look at the Samsung! Shame on you Maytag. Not one good review on here and you do nothing to restore confidence in American Made. I will spread the word - NEVER by a Maytag or an appliance from Menards. Neither one stands behind the piece of junk!

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

Maytag front loader model number MHWE251YG - Purchased washer and dryer 2 years ago. Purchased extended warranty from Lowes. Have had the washer worked on by Lowes repair service over 7 times. It stopped working again tonight. Full load of soaking wet clothes, it wont drain or wash anything. Just hums and then beeps just like all the other time it stop working.

This one of the worst purchases I have ever made! Paid over $850 in March, 2015 for the Maytag Bravos XL. At first, we experienced leaking and now there is a terrible banging and clanging noise! Had an appliance repairman come to see what was going on. Apparently it needs a hub replacement and bearing replacement. Was told by two companies that it is not cost effective to fix it due to the amount of parts and labor.Aside from this major issue, I never felt that the clothes came out clean. Many times, the clothes would come out with detergent all stuck to the clothes and had to be rewashed. The softener and bleach dispensers are not removable and it is nearly impossible to get all the way into the cup in order to clean the mildew that builds up. The fabric softener dispenser always had gummed up chunks.Called Maytag several times to no avail. Was basically told - too bad its out of warranty. I have never heard of a washer giving out after 3 years! The worst part is that I have searched many places on the Internet and apparently the bearing problem seems to be a common issue with this washer. I purposely bought an American made product and am extremely disappointed in not only this product, but the company as a whole. The customer service department is awful. I will NEVER purchase Maytag or Whirlpool ever again. They lost my business for putting a terrible product on the market and refusing to acknowledge flaws. Interesting that this model is now discontinued, but they refuse to acknowledge the problems. Stay away from Maytag and/or Whirlpool!

A pure piece of junk this wash machine is. It is more of a merry go round than a wash machine. I do not understand how it can be called energy efficient. All it does is spin and spin and clothes come out as beautifully dirty as they were loaded. If you make the mistake of putting a few extra clothes (machine calls itself a large capacity), clothes bunch up and one has to pull them apart. The bleach dispenser was used as one would use a bleach dispenser. However it is all rusted. I had bought extended warranty from Lowes but Lowes did not honor the warranty saying rust was a cosmetic issue. Yet when Lowes sold the extended warranty, they did not specify cosmetics were not covered. It is not even cosmetic. It simply is cheap enamel paint.I have used 200 dollar wash machines but never have I experienced such a horrible and annoying product. I will try one more time to see if Maytag will help out with the rust issue. If not, I will simply cut my losses and buy a regular cheap machine. Maytag should be ashamed of itself. I bought a Maytag because I thought they made the best machines!!! Oh! Well, maybe they did at one time.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

We bought a Maytag dishwasher on 9/22/2012. Model number MDB7759SAB. Within the past couple of months, it has been very temperamental. The control panel started beeping continuously and some of the functions wouldnt work anymore while others continued to work too well; in that the dishwasher on occasion would rewash several times without anyone starting the machine again. The dishwasher also started leaking water... As of yesterday, the dishwasher control panel stopped responding and then out of the blue, the dishwasher turned itself on in the middle of the night! We called customer service and they said they could send a repairman out for around $89 and then we would have to pay for the parts needed and the cost of labor. After reading many reviews sounding exactly the same as mine, my husband and I are against repairing this lousy machine. Its absolutely ridiculous for a dishwasher to quit unexpectedly like this. Our question now is, which brand to purchase for our next dishwasher? No more junk please!!

Had this front loading washer 13 months when the circuit board failed. I pitched a huge fit as Maytag wanted to charge me 75% of a new washer for the circuit board replacement. Fortunately they caved. I like how well it spins out and washes well. The door gasket is hard to keep clean. Has fresh setting so clothes do not get moldy if you leave them too long.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

We bought a Bravos washer 13 months ago and its been problem after problem. We had 6 service calls and the problems continue. From bearings being replaced to sensors to error codes, and now the washer drips water. This is the worst washer I ever owned.

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

I purchased this washer two years ago. It is supposed to be high efficiency so I was using cold water with the Water level sensor. The first load of dark clothes I washed came out with soap streaks all over them. This happened every time I washed dark clothes and sometimes they were barely wet. I emailed Maytag but they didn’t reply, so I called customer service and was told I should always use warm water and when washing dark clothes select a deep water wash. How is this HE?? When I wash towels or sheets everything comes out tangled and I am only putting in one set of queen size sheets. I will never buy another Maytag.

My Maytag fridge was purchased on 2006 and since then have had multiple service repairs. Too much freezing, not cooling at all, fan replaced. Now freezer door not sealing.I tried a few days ago to get extension on warranty but was told it had expired so I could not renew. Why wasnt I told I needed to renew back in April before it expired? I believe they are not renewing because of the history of the appliance as it has too many repairs, it will not be cost effective for the company. We have also, in the last 10 years, purchased a washer and dryer and a large screen TV and all have the same problems. What are the chances of getting all lemon appliances? Obviously we are not shopping there any longer but many people are going to have to deal with same issues we did. All the while the company keeps making money!

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

This is the worse designed product. The gaskets on the door keep making mold. The end caps that hold the pantry lid keeps snapping off, had to replace them twice. It is a very elaborate and complicated installation which of course they will not cover. The water dispenser is inside the left side of the fridge and the water runs so slow, that you lose a lot of the refrigeration by the time you fill a glass.This appliance is very noisy. The customer service is sometimes nonexistent. I called on 9-16, I waited 24 min on the line and decided to hang up. The next day I tried again after 15 min they hang up on me. I tried again later got Customer service, but no they could not help me with installation of a replacement for a warrantied part that snapped off for no reason at all. I have complained while this appliance was under warranty, and after. They do not care. My advice is stay clear of Maytag refrigerator, I CERTAINLY WILL.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

Refrigerator (Model Mff2558vems) purchased end of November 2011. Early in 2013 notice refrigerator first forming ice all over freezer, including an ice sheet on bottom of freezer. Then noticed water around refrigerator. Called maytag and they sent repairman even though a little over year and out of warranty. Their service people seemed to know exactly what was causing the leak as they came in with the correct replacement part. Worked fine however, there was damage to my newly refinished hardwood floors which Maytag did pay to repair. A couple of days ago I opened the freezer and again noticed ice all over freezer. The next day, water all around freezer. I cleaned everything up, so I thought. The day after, we noticed the hardwood in kitchen buckling up far from refrigerator and the laminate in dining room bubbling, even though there was no visible sign of water. Called Maytag repair company but they couldnt come out for a couple of days. Called another local repair service familiar with Maytag refrigerators and he couldnt find anything wrong with refrigerator even though he knows leaking caused by refrigerator. Called insurance co. and they sent over service master. Leak is definitely coming from refrigerator. They had to pull up hardwood floor, part of walls, the dining room. They now have five large fans going and a defroster to dry things up. This is upsetting, as my daughters wedding is next month, my husband is currently laid off and I dont need this kind of aggravation again. I love the french door idea, so roomy for my large family, but I am now afraid of this refrigerator. I dont want it but think it is ridiculous I have to shell out more money when the refrigerator is less than 3 years old. I talked with a higher level supervisor at Maytag and they are only willing to give a 100.00 rebate towards a new refrigerator since the refrigerator is out of warranty. This is ridiculous. I thought by buying American I was helping our economy but what I got in return is heartache and crappy merchandise. If there is a lawsuit in California against Maytag about these refrigerators I want to join. My friend in N. CA who bought her Maytag refrigerator the same time I did is also experiencing leaking. So frustrating.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

When my stackable washer finish its complete cycle, there is water left in the tub. You can manually turn the tub and you can hear water sloshing around.

I purchased this dishwasher from Sears in July of 2013. Barely 3 years ago. The last few months the controls have been acting odd. The control lock would automatically just turn on at odd times. Yesterday when I hit normal cycle it went to a different cycle and had many other options lit. It would not start. Finally it went dark, no lights, no nothing. I see many people have had these types of issues with this type of Maytag dishwasher. Disappointing. A dishwasher should last longer than 3 years. Sears said they would send a repairman out but it would have been minimum $200 after it was all said and done. Id rather own a non-Maytag dishwasher so we went and bought a different brand.

The Maytag Washer Model # MVWB835DW is the worst I have EVER had!! I have 6 kids, my husband and myself who I do laundry for and this was supposed to be a XL washer so I can do large loads! It does not do anything to stains and all my clothes come out with clumps of powder and if I use liquid it leaves greasy residue on them! Everyone in our home has had rashes from the washing powder not getting rinsed out and my husband who gets grease and oil on his clothes has all stained clothing because of this washer that does NOT clean anything! I used to be able to get every single grease and oil stain out until I purchased this washer! My 9 yr old now has a scalded skin from the washing powder not getting rinsed no matter how much I use!! I even tried using vinegar to make it dissolve and it does not help! No matter what we do it does not fill up nor wash the clothing properly!! This washer needs to be discontinued immediately and anyone who has it have the option of exchanging it with a better washer! It is absolutely ridiculous that they know this washer does this yet keep selling it!

Have not had either inspected, but last night the dryer started to rumble and then caught on fire... Fireman suspected bearing bad and caused a spark igniting dryer; washer has started making a shrill loud noise on the spin cycle.

I purchased this five-burner gas stove two years ago. I have this stove repaired three times. The first and second problem with the stove is when I turned on the oven, it would never click on. This was a month after I purchased the stove. They sent someone over to correct the problem and that did not work. The third time someone came. He changed something in the oven and it started to work. After that, I continue to have trouble with the oven. When I have the top eyes on, the oven will not work. When I only turn on the oven, it will go to 350 only. It will cook for an half hour and then cut off. I smell gas in my house and my food is smelling like gas. I have stop using the oven. I did not purchase a stove to not use the oven. This is totally ridiculous!!! I am tired of this situation. Maytag needs to recall these ovens, so I can purchase an oven that works. I have thrown food away because it smells like gas - because the oven will cut off in the middle of cooking. I am very tired of this situation and when you call Maytag, their customer service is terrible. I will never buy Maytags products again. Please help.

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

Ive owned the stainless steel version of the Maytag dishwasher model MDB7749SBM purchased on Sept 6th 2013. July of 2014, my first control panel went out. Lights not responding. Was within the 1 year warranty period. Now, that panel is acting up again. I called Platinum Factory service and they wanted to charge me for a new panel and the labor. Well, I used a few choice words on how I felt and the customer service person said the part would be free. Well, nothings free as I scheduled a visit by the Platinum Factory Service. They of course call 5 times to make sure you are home. The day of the service, the tech calls me to see if Im home. I of course said I am... then, he goes to tell me the labor charge for him to come out and hourly rate will come to $189!!! I said screw it and dont bother. Maytags quality and engineering SUCK. Avoid them...