I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

Bought a Maytag Washer, in 2010 the Bravo. Good looking washer and dryer. I bought a 4 yr warranty for both. My washer has needed service every yr of the warranty, leaks and has stopped running. Now it is out of warranty and it is leaking again. Was just fixed a little over a year ago. I am now seeing a lot of rust around the top of the washer. It has just about covered the one port where you put the bleach in. The seam around the top in the crease is full of rust. My dryer is fine, bought them both at the same time. I have never seen this on a washer before. My mom has had her Maytag for yrs no problem. I bought these thinking they would last, boy was I wrong.

After only 3 yrs of normal 2 person family use my Maytag washing machine completely failed. The ball bearings in the transmission seized requiring the replacement of the transmission. At the same time the control panel failed yielding the machine completely unusable. The repair cost was more than originally payed for the machine, forcing me to purchase a new one (not a Maytag). Maytag said since there was no recall on this model that they could not help me. I bought the Maytag because of their claim of quality. This was not my experience either with the product, or the customer service.

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

Model MMV4205FZ3 microwave hood combination. No problems with open door signal yet. However, light over the stove burnt out. When removing, it exploded.No didnt unplug first. Previous microwave didnt have a problem with this. Instructions are useless. Didnt say to unplug and doesnt provide a model number for the bulb. Consequently, we have now purchased 5 different bulbs and they dont work. Tested socket and power is going to it. Rep at Ace Hardware said he had heard about this happening several times and provided what was to be the correct bulb -- didnt work.

I purchased the Maytag Bravos MCT HE washer in 2011. Its about 3 1/2 years old and there was a very loud noise when the washer went into the spin cycle. Called the repair man and they told me the bearing and spin basket needed replaced. I had always had Kenmores with very little issues and they lasted for 12 years plus each. I get the HE model from Maytag and cant even go 3 1/2 years without some major issue. I called Maytag (Whirlpool) to complain and they said there wasnt anything they could do. I reminded them that I had checked for recalls on this model and looked into some of the complaints about this washer and that there were many of the same issues that I had plus many others. I felt like there should have been a recall on the bearing since they are going out too soon for this kind of a washer. I guess the Maytag repair man is now busier than ever since I dont see them on any advertisements anymore. Well, I will never buy a Maytag or Whirlpool appliance again after this.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

We purchased all Maytag home appliances when our home was remodeled about five years ago. After the first year, the microwave had to be replaced because it malfunctioned. The dishwasher stopped working in the third year, and now, my refrigerator (model# mf12568AEB) wont cool. The technician told me that all of the Freon had leaked out because of a design flaw. Moisture had gotten into the compressor, and with the cost of repair or replacing the compressor, I would probably be better off buying a new refrigerator, preferably not a Maytag.

My husband and I purchased both a Maytag washer MVWX655DW1 and dryer MEDX655DW1 less than 3 years ago from Sears. We had both the washer and dryer professionally installed. Yesterday, we had an authorized service man come in and look at the problems we were having. He told us our Maytag washer would need a new gear case and gears costing $750.Our Dryer, same age, needed a new cycling thermostat. He said it was due to not cleaning out the lint trap. My husband and clean the lint trap after every load religiously. He said there was a pile of lint built up in the dryer. I could only think this would be a design flaw. To repair the dryer it would cost $350. The grand total to repair our Maytag Washer and Dryers would be $1100. We paid $1082.38 at Sears for both. The only thing Maytag offered to cover was a part for the washer which would cost $640 and we would need to pay the extra $110 for service in addition the $150 diagnostic charge, due to use being out of our one year warranty.We decided to not fix this machine to avoid similar problems in the future. I talked to customer service and asked them to cover the diagnostic charge instead of sending the part, which is far more costly. I got the runaround and 3 rejections before they finally agreed to pay for the diagnostic charge. My husband and I are extremely disappointed in this experience. We currently own a Maytag Microwave and Electric Glass Top Range. We will never buy Maytag again. Our Stove is also lacking. We have the AquaLift cleaning stove. The AquaLift technology does not work.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

We purchased our Neptune washer and dryer combo MLG2000AWW from Circuit City in 1999 for $1900 also purchased the extended warranty. Here we are 15 years later and time to replace with new Samsung units. Besides having the main bearing replaced after 6 years in service, and having a sensor and a switch replaced on two separate occasions all covered by the warranty, our Neptune provided exceptional service throughout the 15 years. My understanding was that Maytag was bought out and run very poorly in the early 2000s as our unit was produced prior to that time... when Maytag was Maytag.

Our Maytag washer 4000 series was installed on September 2010. Within 12 months and 5 days, we are now waiting for our second spin bearing to be replaced. It is a repair that takes 2 guys and 2 hours, and they basically have to replace the guts of the machine. I can imagine this is, at minimum, a $500 repair. We didnt buy the extended warranty, but luckily, the appliance shop was able to talk Maytag into eating the cost since we were only 5 days out. With the purchase of our new house, we upgraded from our appliance allowance to this model. With everything going on with the new house and selling our old one, I didnt do my normal internet searches for customer reviews and that was a mistake!Maytag has since sent us a warranty extension offer for $350, covering 3 more years. I guess Ill be buying that. It sucks that you pay top dollar for a washer only to find out that you have to pay an extra 40% just to keep it running for 4 years. No more Maytags for me, ever. Note to Maytag, you sell junk and your business goes into the ground. You are selling junk! Stop trying to squeeze every penny out of design and build, or you wont have a job.

In April 17, 2015, I purchased another Maytag microwave but wanted the convection oven too from Home Depot. The convection fan quit working in January 2017. I called Maytag to ask how this was covered. Maytag only has 1 year warranty on parts and labor. So basically if you dont buy an extended warranty, you are stuck with a product that quits working. Apparently, Maytags work is only good for 1 year or they would have a longer warranty. I told the Rep this when I spoke to him. He told me they normally last 5-7 years. Wow, still not acceptable. He said I had two options. Maytag could send out a repairman and it would cost almost $300. The other option was just as ridiculous. I told him I paid almost $500 to start with and it only lasted 21 months. Of course he said if I had bought extended warranty it would have helped. If I paid $500 for an oven, why should I have to pay more to cover their bad workmanship?!! I am very disappointed in the quality and price of this convection oven. The bad thing is I bought all new Maytag stainless steel appliances in 2016 to match the convection oven. The products I replaced had been in my home for 12 years with no problems.

6 week old High Efficiency Washer leaves lint and soap lines. Ive tried deep water wash plus the 2 rinse settings and I still have to wash the load twice to get rid of the lint lines and soap lines. Ive also tried every combination of settings to no avail and I follow the guide to a tee because this machine actually weighs the clothes to determine the water level. Maytag customer service was polite but useless. Im assuming its the poor design but customer service says I will be charge for the warranty service call if no problem is found. Maytag, another fine company down the drain. PS, parts are made in China.

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

It's mounted above the stove, ten years old and still looks & operates like brand new. Have never had a problem with it and it's used almost daily. From heating up food to making dinner & popcorn. This is the longest lasting microwave I've ever purchased. Maytag made a great product.

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

We have a similar problem to the others who gave reviews on their still NEW Maytag refrigerators. Ours isnt even four years old and several weeks ago we started smelling a chemical odor which then permeated all of our food in the refrigerator and freezer. We didnt buy the extended warranty because we have owned a few refrigerators and all have lasted just fine for 15+ years with no problems. So I called Maytag. They said for a charge of $369.95 they would schedule a repair and would cover the service call, parts and repair and provide an 12 month warranty. If the service call results in an inability to repair the refrigerator, they will refund the full amount of $369.95. So I asked if Maytag would then replace the refrigerator, and the rep said we have to start with the service call before they would discuss any type of refund or replacement. Im angry and disappointed in Maytag. Its a good thing we have a spare refrigerator in our basement. What a hassle! Weve already had to throw away over $100 in food that picked up that horrible odor. Shame on Maytag!

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

Leaking water and puddles in front (each side) of refrigerator. Purchased from Home Depot on 12-20-2011... After doing a search on the internet I found that this is a common problem with the Maytag refrigerator. This model is a two door with ice maker on left door and freezer on bottom of unit. Looks like Maytag does not want to be bothered with my problem. Model #MF12569YEW. It certainly was not an inexpensive model. Whatever happened to the Maytag repairman who was never needed because the Maytag products were so great???Updated on 03/21/2015This is not the first time this Maytag product had problems. Expensive piece of junk in my book! First, as many consumers have experienced there was water leaking in front of the refrigerator onto our hardwood floor. Now the door gasket seal ripped on the end tabs. What happened to Maytag?

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

I just got the washer 2 days ago! Its horrible! What type of quality assurance dept are running? Or is there even a QA team?? I put a big load and selected Hot & Power wash. There was hardly any water. It was cold. The detergent nor softener never dispensed. This is the worst washer ever!!!

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

Maytag is the worst dryer ever purchased. We bought it in 2019 and the heating element broke. When I contacted Maytag directly, they said, nothing they could do. Really?? A major part was defected and there was nothing they could do! Its very sad when a major company that you purchased from shuts you down with a defected piece in their dryer and they chose not to help out the consumer. Shameful! I will NEVER purchase another product from them again...

I purchased this gas range from Home Depot in 2011. From the beginning I had problems with the cooking racks slipping off the oven wall. In some instances hot liquids poured on the oven floor. I had bought a service contract on this product and when I asked that this be repaired I was told that it was not covered as it was a design flaw. The condition has slowly worsened and now I cannot cook anything in the oven for fear of the racks falling down. This is a safety feature and the oven should be replaced my Maytag.

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

I purchased a Maytag refrigerator about two years ago because of the Maytag quality hype. The ice maker has been leaking almost from day one and I need to clear out the ice from the bottom of the freezer every few weeks. Now the thing has quit cooling all together. I contacted the Maytag website and they recommended a local authorized repair firm. I took a day off work to meet the service provider. After checking the fridge they informed me that the problem was with the sealed system and that they could not work on it, and that I would need to contact Maytag to get a real Maytag repair person to come and fix the thing (right back where I started). They were however more than happy to charge me $70.00 for a service call. I tried the Maytag 1 800 number which was a nightmare and it finally hung up on me. I then went back to the website and managed to get a service appointment in two weeks (had to wait for a Saturday appointment because I cant afford to take another day off work). I just hope that this time it will actually be someone who can fix the thing and not charge me just to refer me back to Maytag again. I am not happy with the so called Maytag quality or their BS methods for providing service. Caveat Emptor if you are contemplating a Maytag appliance.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

Our washer, still under 5 year parts and labor warranty, wasnt functioning properly. We went through proper procedure having repair personnel first attempt to repair; waited over allotted time for replacement parts, wanted to attempt to repair again, then to replace with sub-standard model. We are now in our 5th month of being told 3-5 business days, 10-14 business days, and I was just told it will be weeks (after waiting 19 days) that replacement will return our call as they are 4 to 6 weeks behind. I have pages documenting dates, times, names, departments and excuses. What can I do at this point? What are my options?

I bought a Maytag dishwasher (model MDBH945AWB3) in March 27, 2010 to replace a Kitchen Aid dishwasher that was only six years old and no longer serviceable. After a little over a year, its dead. When I try to turn it on, nothing happens. If I press the delay button, the lights come on, but in about a minute, they go off.

I purchased my Maytag Bravos XL MCT because It could wash King size comforters/bed linen. I needed a machine that was large capacity. Also it was an HE washer that cut my water usage down quite a bit and reduced my water cost. Also this machine did a great job of cleaning my clothes and household items. The features were good. Variety of load type water temp if it was delicate, bedding, denim and more. I have had it for 5 years and so far no problems. It came with a 10 year warranty.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

Updated on 02/13/2021: Maytag stove purchased 15 years ago for about $500. Replaced mother board about 5 years ago which wasnt cheap, but otherwise, stove has performed with no problems and still looks and behaves like a new stove.Original review: Our 6-7 year old well cared for Maytag range oven recently stopped working. After a service call for diagnostics, it was determined the electronic module controlling the clock and all oven functions was dead. We were told by the Maytag service tech the module cost was 300$. That cost plus labor for less than an hour, plus the 60$ diagnostic visit came to almost 500$ which is close to cost of a new stove. The technician answered yes to my question, Do you replace a lot of these? He also said the cause may be power fluctuations making me think that surely there is a way to prevent this kind of failure. So, since the price seemed exorbitant, I wrote Maytag to inquire about causation/prevention, etc. I received a fairly prompt and polite reply with totally no explanation. I wrote another email with relatively the same results. I dont recommend buying an electronically controlled Maytag stove.

I bought this washer almost 5 yrs ago and oil has been leaking from it. Called company who sent a tech to my home and declared it a total loss. All he did was tilt it for maybe 1 minute to determine this. I am out a washer. Nothing from this horrible company. They quit making the washer but cant even compensate the owner with anything to purchase a replacement. Will keep passing the word.

Bought a Maytag dishwasher early July. Worked great for 3 months. Drain pump went out. Called customer service, 30 minutes to get a person. 1 week to get a service tech here. Even though we told them pump was out. Sent with no repair parts. So has to come back at our inconvenience, company policy, not service tech fault. Tried to complain on live chat. 30 minutes for them to get with me. Still no satisfaction. Would not recommend the product for the company itself. Sadly thought we upgraded.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

We purchased our Maytag Bravos Top Load washer 3 years ago from Home Depot. I have to admit this is the worst washer ever. The clothes does not appear to get clean enough for the amount of time it takes for the clothes to wash. The white clothes look dingy after a wash that I have gotten to the point of pouring an additional amount of bleach in the wash tub. The amount of water that is in the tub is next to nothing, I have to either add additional water or place no more than 20 pieces of clothing in the wash. This is sad and I regret that I wasted my money on this product and I do not recommend it. As soon as I get some extra money to throw away, this washer is going out with the bulk trash.

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

Only 2 months after purchasing the Neptune Washer I required a service call as the washer was not draining. Technician replaced the pump and cleaned the drain filter. 4 months later the same issue happened. 3 months later the computer board was replaced and filter cleaned. Since purchasing this washer I have had to have 5 service calls to have it fixed. I called Maytag and they told me it is my fault the filter is clogged. Although the things in the filter are from my familys laundry the filter is located in the middle of the machine which requires the machine to be torn apart to clean the filter. This is a TERRIBLE design flaw which is NOT covered under the maintenance agreement as the service technician said this problem was caused by us. Maytag was the absolute worse to deal with as I have spoken to two levels of customer support managers and all of them said its my fault.

I have a Maytag dishwasher and the bottom rack has rusted out so that it cant hold dishes. The dividers break at the bottom. I was told by Maytag parts that this is a common problem and theyre hearing from a lot of consumers about this, but it will cost $196 to replace.I spoke with customer service who told me that dishwashers only last 8 to 10 years” and since mine is 8 years old, I should expect that it would rust. Thats unbelievable. They wont replace the rack, nor offer it at a discount.

I have the same complaint as everyone else. I have had my dishwasher since April 2013. Less than 9 months after having it the control panel went out and they came and replaced it. Now June 2015, 2 years and 2 months after purchasing and a year and a half after the control panel was replaced, none of the buttons work except the cancel button. How is it that these machines, as expensive as they are, crap out after 2 years! Such a waste on money!! Maytag has lost my business forever!!

Maytag dishwasher model #MDB7609AWB2 - The control panel on this dishwasher has just gone out for the fifth time since 12/10. Last time I also had to replace the control board also.

On 12/09/12, I purchased a Maytag washer, model mvwc200xw, from our local Menards store. About 6 months ago, the washer started making a slight banging noise, and would occasionally move in the spin cycle. Now, when washing a small to medium size load, the banging noise is very loud and does a lot of moving. I found nothing in the troubleshooting guide to help me on this, so I looked on-line and found several websites discussing this same problem. They stated that the problem was a snubber assembly and the replacement part would cost $4.55. They also said the washer would have to be taken apart to change out this $4.55 part.I watched a you-tube video of someone changing this part and quickly came to the conclusion that I would need help in doing this. A comment was left in the video from a Maytag repairman saying that the person changing this part was not doing it in a safe manner. The repairman stated that changing it in the way this person described in the video was DANGEROUS! I wrote an email to Maytag customer service explaining the problem and asked if there was anything they could do to help me on this 1 1/2 year old washer. I received an immediate email stating they would get back to me in 3 days. Ten days later, I finally received a reply. I was told there was nothing they could or would do even though I was a valued customer and that they understand and appreciate my feelings of disappointment.I worked for a large department store from 1970 to 1990 and sold appliances, one of them being the Maytag brand. At that time, they were considered to be a top of the line brand. This was why I purchased Maytag appliances for over 40 years. I am surprised and saddened to see a lot of on-line complaints against Maytag appliances and also that this 1 1/2 year washer needs to be repaired so soon. Obviously, times have changed. I figured it would cost me at least $100.00 to have this washer repaired. Rather than do that, I am going to take this in need of repair to a scrape recycling center and then go out and buy a new washer, but it will not be Maytag! Maytag will never disappoint me again!

Both the microwave and French door fridge handles are crap. The microwave has completely broken and the fridge is very loose and will soon break, Im sure. Both are less than 5 years old. I will never buy Maytag again.

Maytag Bravo was making loud noise in the Spin cycle. Ordered new bearing, shaft and parts from Amazon. Also had to order the Bearing tool, cost more than the bearing parts. Total cost $145. Watch a youtube video on replacement, took about 3.5 hrs by myself. Biggest problem I had was lifting the washer up over the drain pan it is in. Washer is on the 2nd floor.

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

I’ve had my dishwasher for over 10 yrs now and I probably need to upgrade but it suits us just fine and I’ve really never had any problem with it at all. My dishes and especially my glasses come out Sparkling.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

At 10 months old, the compressor fails. It took one week to fix. Exactly two months later, the compressor fails again. This time, there are no compressors in stock per the manufacturer and the extended warranty folks. Ten days and counting. 90 degrees outside. No idea when they will be available. It’s time to walk this one year old to the curb and get a responsibly built one. I should have held on to my old one. DO NOT CONSIDER A MAYTAG refrigerator.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

Did not know of the lawsuit or recall. Now I have to buy a new washer after fixing it out of pocket and mad that cant get part of the settlement. Not ever going to buy Maytag again!!

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

I purchased a Maytag Bravo washer and dryer in 2008. I had a repair person out today on both units. I was told that it will cost as much to fix the washer as it would be to purchase a new one. As far as the dryer was concerned, I was told to live with the timer issue rather than replace the expensive mother board. I was also told that the drum bearing issue with the washer is fairly common with the Maytag machines. It looks like the Maytag repairman isnt so lonely anymore! I paid a lot of money for these machines and they amount to a hill of garbage after three years. I may be buying a new washer, but you can bet your boots it wont be Maytag/Whirlpool!

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

I purchased an expensive Maytag washer & dryer, top loading, energy efficient, only to find it now shreds all of my towels, robes, dress, undies etc. Maytag reply was to put things like undies, t-shirts, & dresses in bags to wash... What about towels? I had an expensive white Terry cloth robe from Neiman Marcus which is now shredded, Im showing it to everyone. Plus the dryer has an area above the front door that snags everything. I open the door & clothing is hanging there, caught on this area. Tell everyone not to buy Maytag, theyre rip-off. Ive lost more money on ruined clothes & linens than the trash washer & dryer are worth, but Im disabled, handicapped, 61 yr old who cant afford to buy another new washer!

MVWC565FWO Maytag Top Load - Bought a new washing machine less than six months ago... extremely noisy: Clank, Clank, Clank, Clank, etc. Reviews said it was just noisy, nothing wrong with it. Last week it would not spin the clothes dry. Now when it is plugged in, it does nothing but run the pump! No lights, no water. Also the deep wash was never deep at all - barely covered a modest load of laundry. Repair coming today. Wish I could return it.

We are on our 2nd Maytag refrigerator in 6 years and both units have failed. Maytag will not stand behind their product and the service company declined to come out to look at the unit because we were upset and contacting the BBB. So we have spent thousands on 2 refrigerator units that have lasted 2.5 to 3 years a piece. If I could give no stars I would and I would advise to look at other companies and models.

I wish I had found this website before I bought my new Maytag washer and dryer from Home Depot on March 7, 2018. I replaced a 30 year old Maytag washer that I should have kept. I wash two loads a week so has not been used that much and now it will not drain. I tried everything, canceled the cycle out, checked the circuit breaker, unplugged it, removed the clothing, bucketed out the excess water, tried the drain and spin cycle, etc. Just will not drain or spin. Repairman is coming next week... Still under first year warranty but if it is not the “fault” of Maytag I was told there will be a $90+ minimum service charge.

Maytag Dishwasher with model number MDB6701AWS and Serial Number 41687985NJ.It does not clean dishes like it should. We tried every possible way to set control settings, and still the dishes come out dirty and spotted. Also, it doesnt dry like it should. We had a Kitchenaid before we moved and it worked great.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

I purchased my Bravos washer and dryer in about July of 2012. So far I have no complaints about the dryer but I hate the washing machine as do two friends of mine. My husband specifically wanted something energy efficient which is why we didnt purchase the basic traditional style washer weve always used. From the first time I used the washer, I was amazed and disappointed at the noise level. Because the lid is glass, I could observe the water level during each part of the laundry cycle. The water did not cover the laundry in the washer.When I mentioned this to one of my friends, she said that she has to wash some of her clothes twice. How is this energy efficient? I finally figured out that using the heavy duty wash cycle and heavy soil setting usually results in more water but requires an hour to wash and rinse the clothes. The downside is that the heavy duty cycle is too hard on some of my more delicate items so I have to hand wash many more clothes than I did with my old style washer that allowed me to select the water level I wanted. Most recently, when I washed a bulky mattress pad with a few other items, the water level never covered the pad because the load of laundry was so lightweight. At the end of the cycle, parts of the mattress pad were bone dry so I will have to take it to the laundromat if I cannot make the washing machine fill up with water high enough to cover the mattress pad. I dont want to spend the amount of time hand washing so much of my clothing, monitoring the water level in the washing machine and rewashing loads of laundry. After reading many of these comments, it appears that I have many more issues to look forward to. When this washer starts to break down, I will go back to an old style machine and a different brand.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

I purchased this $857 dishwasher from Lowes in May, 2021. It broke in June, 2021. S&S Repair was sent by Maytag to repair. It took 3 weeks for them to come, then they discovered the motor and pump assembly had gone out. Parts were on backorder. It is now August, 13, 2021 and I still have no dishwasher. Lowes would not replace this dishwasher. Maytag will not authorize a return. This is disgusting.

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

March 7th. My refrigerator ice door started flapping and the lights flickering. The next day it quit working. I called Maytag. They said they would have someone come fix it the next week. The repair service people called me back the same day to tell me that the part I needed has been on back order for 2 months. I called Maytag back. They told me to wait a week they put out an all alert for the part. I called back in a week. Now they tell me its 2 months. This is ridiculous and a huge inconvenience. I will not buy anything again from Maytag. $2,800.00 refrigerator should last a minimum of 20 years. This should be a recall. Thousands of people are having this problem.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

Model MDB7749AWB2 Dishwasher - we purchased this dishwasher 3 years ago on 12/23/2011 and it appears to be falling apart. We have replaced two thermo fuses, one door latch/switch and now need the front control panel and handle because two mounting locations for the six screws have broken off. I truly expected a much longer product life than three years when I purchased a Maytag. So much plastic in crucial high stress areas must have slipped by the engineering folks. Or was it just cost cuts. I believe it will be a long time before I consider a Maytag product again based on this one. Thank you.

Purchase this machine Bravo XL Top Load Washer in Dec of 2016, noticed right away every load of dark clothes comes out of the washer with a scummy lint residue on them, some of the clothes are not completely wet when you take them out of the machine. Have talked to Maytag and tried their suggestions that did not work. Seems like a canned speech reading some of the other reviews. I am just at upset with the appliance store that we purchased this from after their sales pitch how these are the best machines made, made in Ohio, great company etc..etc.. Just one run around after another.

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.

MAYTAG HAS ALWAYS BEEN MY W&D MACHINES OF CHOICE! In my opinion they are the most reliable, dependable machines on the market - for years! I would NEVER by another brand of either washer and/or dryer.

Very poor quality. Vegetables freeze at the back of the fridge I have tried everything. The vegetable drawer constantly comes off its track and the freezer door slide jams and stops the door from closing. It leaves about 1/2 inch gap. Now the Whirlpool/Maytag company changed their corporate policy and wont allow an appliance store that to come out and fix the fridge I have to go back to the manufacturer. Their website wouldnt take my email address when I tried to sign up for an account and they wont answer the phone. What a hassle. Ill buy another brand next time but never GE or Whirlpool again!

I had one set of Maytag washer and dryer and I loved it. I bought another set and hate it. The washer smells and has been fixed a couple of times and the dryer is bad. I had to have a drum replaced because of one of the bars inside. I paid for the insurance but the bar was considered cosmetic. It has fallen off again after about 2 years and Im sick of it. I will never buy another Maytag again. Repairman, of course, had to order the drum and then I had to take another day off work to be here when it was delivered and one more to wait for him to come. I am so unhappy with this brand - never again.

I purchased and installed a high end MAYTAG above the stove microwave. After 3 years of light use I hear an electric cracking sound and it dies. Of course no warranty coverage. Model MMV5208WB-1. I have to conclude MAYTAG builds junk and does not stand behind what they sell.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

Model# MVWC200BW1 bought in 2015 tangles/stretches clothing. This machine is/has been a true disappointment. The agitator wings are not attached at bottom allowing clothing to get caught and as the agitator turns, so does the clothing causing stretching and severe tangling. Poor design compared to the agitator that would rise and fall - those got clothing clean and did not ruin them. I cannot trust this machine to moderately cost clothing for fear of their demise. The lock-down mode is not convenient for those last minute added items. Will not be buying Maytag/Whirlpool ever again when another machine is purchased. This is a piece of rubbish!

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

It was alright for a while. Then it started ripping up my clothes. The machine is not overloaded, enough water has been added but, when I take the clothes out they are torn. Not a good experience. I have seen several reviews on the Centennials, none of them good. What is the problem. I am hoping my experience gets resolved.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

My Maytag MDB7609AWW2 dishwasher was purchased on 1/2010. Last month, the control board only worked on the right side of the panel and the dishwasher would not run. I called Maytag to see if this was a typical issue with the washer, which they denied. I ordered and replaced the control panel but this did not help. After reading all these posts, I do not think Maytag is being honest with their customers. Also, it looks like even if I am able to fix this issue, it is likely to repeat. I think I will cut my losses now and buy a different brand of dishwasher. I will never buy a Maytag again.

Maytag products are a waste of money! I purchased a Maytag Front Load Washer a couple of years ago during the Cash for Clunkers rebate where we were asked to give up our reliable machines for so called energy efficient new models. After spending over $1,000 on this fancy front load machine and having it installed, I go to use it the first time and it won’t work. It took me a month to get someone to come and repair the bad board on it. I then started to use it and after a year, the thing started making a horrible loud noise. I called the repair folks and they told me it is out of warranty. I called a local repair guy who told me that the drum is shot and that it will cost $700 to repair. So I got a total of 10 months of use out of this stupid thing. Thats $100 a month to do my laundry! I would be better of dry cleaning! I have searched the web and see that this is a common issue and that Maytag refuses to make this right. Well, I can choose to never buy a Maytag again. I hope that others will heed our advice and do the same.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

In reading the reviews of a Maytag Dishwasher, I am also frustrated in the dishwasher is only 3 years old and the start button does not work. It cost $75.00 for the repair person to come in to take a look at it which they deduct from the cost, total repair cost $300.00. Did not make sense at this time to have to pay the $75.00 repair person and then purchase another $500.00 dishwasher so paid the total $300.00 hoping to get a few more years out of Maytag dishwasher. By the other reviews, may not be possible. Just very frustrating.

I am a regular customer of Leons and used to buy all my home appliances from them, because I trusted their quality and service of their products. However, last time I bought French Door Maytag refrigerator from them, about two years ago, we suffered from defects in this type of fridge. The problem started before one year when my wife saw some leakage of water on floor in the front side under the fridge freezer door. In the beginning, this was occurring once a month or every two weeks, so she didnt think it would be a problem or it might happen occasionally. However, the water leakage now became worse and almost every day. We had to put a towel permanently under the freezer door to dry the water which appeared ugly. Also, I had couple of accidents that my child slide over because of that water leakage. I spoke to one technician, he told me resolving this type of problems is not guaranteed because the problem will appear again or after while. He said this could be a manufacturing defects in this type of Maytag fridge models!!! Another problem appeared also one year ago, that one of the door handle started to shake very little, but now it looks like moving from its position and there is no way to fix it!!!Therefore, when I requested the help from Leons they told me that, You didnt buy the extended warranty and we cant do anything for you!!! You can talk directly to Maytag. Then, I send email to Maytag explaining the problem. They even didnt bother to reply or call me. Now, I feel that I was bluffed by these companies. I didnt think that I was buying a $2,000 refrigerator to scrap it after two years. That is ridiculous when you buy defected product from them, but they dont care to resolve the issue.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.