Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

Works like a Dream!! My dryer is an older model Maytag and it works wondrous. I have tried the newer energy efficient kinds and I feel like they dont dry well or make my clothes smell clean. My older maytag works fast, efficiently and I love how my clothes feel fluffed and smell fantastic!

Worst washing machine!!! I purchased the top loader Maytag Bravos washer HE in 2011 and they are the worst!!! It has been repaired three times already and now is making such a loud noise and I have been told it is the bearings. I did purchase the extended warranty and it expired. The reason I did not get a renewal is Maytag & Home Depot do not allow the the extended warranty company to let you know the warranty is ending. So now I have a 3 1/2 year old washer that needs bearings and will cost $500 + for repairs. Will not be spending anymore money on this absolute piece of junk. I had a Maytag that was 22 years old that I replaced and thought I was buying the same quality but never again another Maytag. This company may want to employ only repairmen because you will need only them because no one should buy a new one going forward.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

I had a warranty that I bought over a year ago. The dishwasher since then has been a monster beyond control. I called Maytag and the woman asked how long it has been acting up. I said about a year, but I was not sure. They refused to honor my warranty because they said it would only go into effect 60 days after I purchased it. They are translating about a year as an absolute and refused to honor the warranty. I would never ever buy a Maytag product again. Never. I will contact every person I know not to buy such a faulty product.

Purchased a Maytag bravo washer model #MVWX500XLO 2yrs and 6 months ago April 28/2011. In Dec. 2013, I heard a loud clanking sound and was shocked. I thought that some coins were lodged somewhere.... not the case. I put up with the clanking until after Xmas.... Finally I called a licensed technician (in business more than 20 yrs). He immediately identified the problem.... THE TRANSMISSION was shot. Wow what a shock! 65.00 dollars house call to give me the news. I phoned head office to no avail. The office said that it is not covered and that the part would be in the neighborhood of 350.00 $ and probably the installation around $160.00. I am still in shock. We paid around $750.00 for the unit. The technician said that it is one of the worst machines he has ever worked on. I am now talking with Home Depot to see if they can get some compensation on the unit (speaking with the rep). Will I buy another Maytag (by the way) made by Whirlpool... I guess not.

Maytag side-by-side fridge with water/ice dispenser (Model # MSD2572VEW00) was purchased in 2011. Mechanically, fridge is working, however, every piece of plastic inside the refrigerator section (the regular glass shelves with plastic rims, vegetable bins, and door ban shelves) are all cracking and falling apart. Additionally, the buttons on the ice/water dispenser fell off, exposing the actual buttons on the panel. All three of the regular sized shelves have severe cracks in the plastic that affect the sturdiness of the shelf. Both vegetable drawers are badly cracked, falling apart and one doesnt even stay secure on the track. Even all three of the door ban shelves are cracked with fractures along the sides and bottom. Weve resorted to putting clear packing tape just to hold the shelves together.We contacted Whirlpool, who owns Maytag and because our fridge is 4 years outside of the 1 year warranty, they could do nothing for us. In over 30 years of owning refrigerators, this is the first time Ive seen every shelf and bin crack the way this fridge has and in less than 5 years no less! Whirlpools solution to our issue was to send my call to their Parts Department. The total cost to replace all the cracked shelves, bin drawers plus the ice/water dispenser panel is $702.28. No thanks, thats as much as a new fridge. Whirlpool should be utterly ashamed of their total lack of Customer Satisfaction by distributing such a piece of junk. Who would have thought that an appliance costing a couple hundred dollars would be considered as disposable as an aluminum pan and in only 5 years! One thing is for sure, I will certainly think carefully again on ever buying another Whirlpool product again since they are so apt to take my money only for me to repurchase an expensive appliance again in less than 5 years.

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.

I purchased my Maytag side by side refrigerator 11/2011 and by 3/2012 the compressor went out flooding my pool house floor. Maytag replaced the entire fridge because I was only a few months old. I bought the 2 year extended warranty, went down to the pool house (which has central heat and air) and the compressor has gone out again! The results leaving my baseboards molded! My warranty went out 3/17/2015 and Maytag is helping NONE! The only thing they have to say is you can buy a new repair one warranty for $363 to repair for one year. I have had this refrigerator for 3.5 years and now this is the second time its gone out! Customer service said, pool house is different than a regular kitchen. I told her that the pool house is 1,000 sq heated/cooled kitchen, bathroom, sitting room. Thats no different than some houses. Why would that make a difference?? My parents have a 30 year old fridge on the back porch thats still running! I will NEVER purchase another MAYTAG product! Stainless side by side with ice maker.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

This is not my first Maytag. Bought this one in August 2017 from Home Depot. Now all it does is make a grinding sound. No lights. Not anything but noise. I bought one without all the digital because I thought that could be more problems. The only part that is digital is the start/pause button. I liked the idea of less water and no center. It balloons the clothes when it is finished spinning. Didnt start out that way. I use the right detergent and wash it every 30 days as it suggests. Cant afford to call a repairman on such a new washer.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

7 years is all I got from these appliances. The Maytag Washer started making a horrible noise when washing then smoke and shut off. Dryer would not shut off. We have taken excellent care with these appliances servicing them as we had an extended warranty on both. They cost us over $600 for the washer and $589 for the dryer, a big rip off! I purchased them in hopes I would at least get 15-20 years of service as Maytag is to be one of the best. Do not purchase any products from this company, they also have sister companies. Make sure when you need an appliance, you ask who makes them.

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

I bought this stove thinking of the Maytag repair man commercial that was advertised on TV for washing machines. Apparently Maytag only knows how to make washing machines (I did not buy one of their washing machines after my experiments with their stove). From day one the oven door never closed right, the self cleaning oven device had to be replaced 3 times over the year after have a repairman tell me that they all fail. I stopped using the self cleaning feature. This stove has cost me so much in repairs. The cook top is very very hard to clean. It always looks dirty. All the plastic knobs have melted off because the oven door never closed right. And the knobs are crazy expensive to replace as is just about everything on this stove. The oven temperature can not be trusted never cooked at the temperature it was set at. I paid a lot of money for this stove 10 years ago. And I am finally able to replace it thanks to a Christmas present from my 3 children. I love to cook and this stove made it difficult. My advice is to look for a different company when buying a kitchen stove. This Maytag has been nothing but trouble for me.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

We Purchased a Maytag gas oven/stove three years ago believing it to be the quality of the Maytag of yesteryear, Boy have we been disappointed! When Whirlpool Corp. bought out Maytag several years ago they continued using the Maytag name only.. The quality is now less than substandard, It is a cheaply built piece of crap.. We would sell it in a garage sale and replace it with a quality stove/oven but we dont want anyone else to have to deal with this piece of junk! It will soon go to the landfill!!!

I have a fairly new washer Maytag model #MHWE500VW serial #CSY0303991. I need Part # W10415587 doesnt excist for my washing machine anymore. Its been on backorder since Apr-May 2011. Maytag/GE insists that they are not responsible. As long as they can say backorder technically they are not liable for anything and dont really care that me the customer is having a problem and they Blatantly refuse to even investigate. I spoke with a GE supervisor just today and she basically told me wont help you because my appliance is out of warrenty. And she explained to my that my complaint will go into a file that no one will ever see. I searched the internet only to find hundred of other consumers are waiting for this same part. Ive called distributors & manufactuers. Same answer, backorder. My warrenty people are trying very hard to help me but again Maytag/GE refuse to help. Very dissappointed with this company. Wont be purchasing Maytag/GE products again. Wheres that guy in the commercial with nothing to do when you need him??

I have owned my Bravos XL for over a year. Loads of wash have come out with rust marks. These marks do not show up on all items, only one article of clothing/sheet/towel seems to pick up the rust marks (usually a couple of dots near each other surrounded by a circle). They are always the same. They have shown up on sheets which were washed in a white cycle and on other clothes of various colors.I have ruined numerous new clothes and must accept the fact that these random but frequent rust-colored dots are part of my life. I expected more. Im getting ready to purchase a W/D for our home up North and believe its necessary to return to a basic model, probably a GE. Maytag seems to have jumped the gun on this one… putting new product out there, aware these unresolved issues remain.

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

I have to rewash many load of dark clothing because pale white smears appear on the clothing most times. Ive tried various cleaning methods to try to remove any residue that might be in the walls of the tub. Unfortunately, I cant afford to replace the Maytag white elephant model 500XWZ, serial C31430894. I no longer have the receipt. Buyer, beware. No Maytags in my future.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

Control panel broken for a second time in 23 months: I purchased a Maytag dishwasher less than 2 years ago at Home Depot. 11 months later, the control panel went out. Specifically, the start/cancel buttons stopped working. A service tech called me under warranty; the control panel was shipped to me, and the tech fixed it. He also told me that they had had numerous problems with the control panels.13 months later, the control panel went out; specifically, the start/cancel buttons stopped working (sounds familiar). I can get nothing from Maytag, except a demand for service fees or sales pitches for extended warranties (at a price that was half of what the dishwasher cost new). They also offered me the free part as long as I pay the service call fees. I told them to just to ship me the part and that Id do it myself. Nope. I must pay the repairman. Now, theyll ship me the part if I pay for it, but they wont ship me the free part. It only comes with a service call.Maytag also told me that there were no reports of problems with the start/cancel button, an obvious lie with a quick internet search. The customer service rep sounded like she knew I was getting treated badly and kept using the word policy. Her supervisor was much more cocky and made sure I knew that I wasnt getting anything from her company.They make horrible products, attach what once was a good name, provide zero customer service, and lie to your customers. Great business practices. I will never purchase a Maytag product again.

I purchase the Maytag Bravos washer & dryer set 3 1/2 years ago brand new. I figured being a Maytag it would last for a long time but nope I was wrong??? I will never buy another Maytag product as long as I live and I will tell all my friends and family not to purchase a Maytag product also!

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

Bought Maytag Dishwasher in 2/2012. 10/2015 dishwasher stopped working. My husband tried to replace the motherboard, however, dishwasher completely done. Called Maytag and they said they would send a repair company at their expense, however, repair service called to verify appointment and told us how much it would cost us! Maytag had no intention of paying the bill even after they said they would. Called Maytag back and said the other customer service person was incorrect. Now, buying another dishwasher only after 3.5 years.

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

Our Maytag washer 4000 series was installed on September 2010. Within 12 months and 5 days, we are now waiting for our second spin bearing to be replaced. It is a repair that takes 2 guys and 2 hours, and they basically have to replace the guts of the machine. I can imagine this is, at minimum, a $500 repair. We didnt buy the extended warranty, but luckily, the appliance shop was able to talk Maytag into eating the cost since we were only 5 days out. With the purchase of our new house, we upgraded from our appliance allowance to this model. With everything going on with the new house and selling our old one, I didnt do my normal internet searches for customer reviews and that was a mistake!Maytag has since sent us a warranty extension offer for $350, covering 3 more years. I guess Ill be buying that. It sucks that you pay top dollar for a washer only to find out that you have to pay an extra 40% just to keep it running for 4 years. No more Maytags for me, ever. Note to Maytag, you sell junk and your business goes into the ground. You are selling junk! Stop trying to squeeze every penny out of design and build, or you wont have a job.

I have had KitchenAid and Whirlpool my whole life - lots of them - NEVER EVER have I had so much trouble with a washer. This front loader is the worst possible machine. My former Whirlpool was a front loader too - Never a problem. I purchased this Maytag set simply to have a matched set because our Whirlpool dryer died. This washer has to be babysat. The washer holds water and it gets musty - never ever before have I had this problem. Maytag says it is designed this way and I have to continue to buy AFFRESH (which is also very expensive). I have to use this two to three times a week and the pkg says once every 6 months - DONT DONT BUY MAYTAG. LOUSY.

2 major repairs in 8 years, ridiculous! We purchased a washer and electric dryer pair in Feb. 2012, had a repair for the control board (CPU) 4+ years under extended warranty, had another in 2018 for the same thing. I was told power surges could cause it, however I have a WHOLE HOUSE SURGE SUPPRESSOR ON THE INCOMING 200 AMP SERVICE AND KNOW THATS NOT THE PROBLEM!!! Had the same CPU go out again in Nov. 2020 so, rather than pay $370 for the part plus labor, we bought a top loading GE with an extended warranty and factory 10 years on the motor. We will never buy another Maytag product again. We were told that we shouldnt expect to get more than 6-7 years from a washer now, ridiculous. Manufacturers are outsourcing electronic boards overseas to maximize profit and could care less about quality control!!! Junk!!!

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

I have had a Maytag smoothtop stove for over 20 years. The only drawback has been when someone left an empty pan on a hot burner. Some of the pan melted to the top which could not be removed. I have to get special pans to conduct the heat, too. Overall, I love it. It has a self-cleaning oven, too, which is a bonus.

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

It’s the worst washer I have ever encountered! I never have clothes that smell clean. The water seems to never completely spin out, the spin cycle is terrible!!! My whole house shakes when it’s spinning and the noise coming from it is so loud. The time on it is never correct; it will say there is 9 minutes left and then just go to 1 and quit! My clothes have never looked clean with this machine. And yes, I use very good detergents and everything else to try to help with no luck! The dryer just takes forever to dry anything. Needless to say, I will NEVER purchase another Maytag again!

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

Thankfully, Home Depot replaced the washer when Maytag wouldnt authorize a replacement after I had it for 3 days. Maytag wanted me to order a part, wait for the part, and then schedule their third party service contractor. It’s been about 2 weeks without a washer. Ive been posting about my experience and received an email from Maytag asking me to post feedback on their site, but it was rejected. Their note to me was “Our publication guidelines do not permit content that references a service policy, customer service interaction, or customer service question.” In other words, theyre not at all interested in customer service. Maytag/Whirlpool is no longer the brand to look for.

I am PISSED off at Maytag products in general. First I buy a washer and dryer from a Maytag store-buy a 12 year warranty. Call in for repairs - Maytag and A & E say I have no coverage. Now I am getting bills to pay for coverage on both because the form says my coverage ends this December 2011. I buy a Maytag dishwasher and its the one that catches fire. I get the rebate of 250 for buying the more expensive one - but am still out 500 dollars. Installation was bad by contractors from Lowes - just called that in to have it reinstalled. AND THE MOST RECENT IS THE FRENCH DOOR REFRIGERATOR I BOUGHT 9/4/2010. IT STARTED ACTING UP AROUND CHRISTMAS TIME - WEIRD NOISES, WOULDNT MAKE ICE - I AM SO BUSY WITH MY MOM I DONT CALL IT IN UNTIL JUN 25TH AND THE REPAIR PERSON SAYS IT IS UNREPAIRABLE AND HAS INTERNAL DAMAGE TO THE WIRES.

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

The Maytag has nice features but the shelves dont allow much room to adjust them and the freezer could stand to be a bit larger but overall its a good and hard working fridge for the price. Would love if those two things could be fixed without a huge price tag.

We trusted the Maytag name to give us a good product that would last. After six weeks the Maytag Bravo stopped working. Having to wait 7 days before a service repair person came to our home. The main motherboard needs replaced. So currently, we are still waiting for the part to arrive and have it installed. 2 weeks without a washer after spending 600.00 for a new washer. There is more problems also, this machine takes 1 hour to complete a single load of laundry. Plus it does not get the clothes clean and the rinse cycle does not get all the soap out of the clothes. Very unhappy with the Maytag Commercial Bravo. Will not buy another Maytag product. Save your money and get another brand. We plan to get this one fix and sell it.

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

Just like all the other reviews, 14 months after purchase and 2 months out of warranty the control panel on our Maytag Dishwasher stopped functioning. The “10 year warranty” is a joke a covers 3 things. We had model MDB4949SHX, $550 new.

At 10 months old, the compressor fails. It took one week to fix. Exactly two months later, the compressor fails again. This time, there are no compressors in stock per the manufacturer and the extended warranty folks. Ten days and counting. 90 degrees outside. No idea when they will be available. It’s time to walk this one year old to the curb and get a responsibly built one. I should have held on to my old one. DO NOT CONSIDER A MAYTAG refrigerator.

Maytag dishwasher mdb7749sbm2. Purchased the above Maytag dishwasher model in July 2013. Eight months later the control panel ribbon strip burnt out. The first of many times to come. I had the panel replaced three times during the first year (warrantied by Maytag, now Whirlpool). All I can say is thank goodness, I paid $30.00 for the extended 3-year warranty. It has been the best $30.00 I have ever spent. Unfortunately it doesnt count for all the frustration this appliance has caused me. Ever since the first repairman walked through the door, all he could say is that the control panel was poorly made, electricity and water does not mix and never will. When you use the steam option all you are doing is adding to the problem. (The steam option is the sole reason why I bought the model in the first place!)Anyhow, this model has broken down three more times and it is currently down again as I am writing this, awaiting for a service person to hopefully come out as promised next week. I purchased this appliance two years ago and still have one more year of warranty left. Once it is done, I will be shopping for another dishwasher. If I didnt have it covered with a warranty, I would be paying the service fees of about $251.00 each time they came to change the panel. Shame on Maytag/Whirlpool for not recalling this model.

I wish that I had looked up reviews before purchasing my washer 6 months ago! No matter which setting I use, the washer never fills up with enough water!! I have pulled clothes out that havent even gotten wet, due to not enough water in machine! All due to the government regulated water levels on the sensors!!!! So, I had my plumber put in hot and cold water faucets, then he put a short Y hose on, so this way I can add water to the machine.... The only thing is, you have to wait for the machine to fill with what it thinks is enough water to get your load clean.... stop the washer, then add the water you need. But if it reaches a certain point, it will automatically start draining. So you have to watch and make sure you stop adding the water, before reaching that point!

Purchased this Maytag microwave brand new on April 2017. In January 2019 began to have issues with the display reading open/close door. Maytag would send a repairman for $160 to take a look at the problem. Parts of course are extra. I will never buy a Maytag product again.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

After 18 months of use Our Maytag Dishwasher (MDB7749) has the same control panel problem as a lot of other user complaints. I wish I too had read the consumer reviews before my purchase. We will never buy another Whirlpool product!!

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

I purchased the Maytag Bravos XL washing machine because I wanted a top loader that was water saving. This washer boasts of a 10 year commercial capacity so I thought I was buying a decent machine. Unfortunately I have had a very disappointing experience. From the start this machine has not cleaned clothes properly. We circle clothes around the agitator and only fill the machine a third of the way full. This is the only way to ensure clean clothes. We use HE soap.As if this hasn’t been bad enough, the entire motherboard seems to be glitching out. It throws a different code each load and sometimes won’t start. Other times it won’t stop. It isn’t safe to use when we aren’t home or are asleep, making the time delay feature useless. Last night the machine ran for 2.5 hrs on a 1hr 30 min estimated deep water wash. I finally turned off the power and let it drain out after it insisted it had 45 min for the last hour.... this thing is a total waste of money. Will never buy another Maytag!!!!

I have been buying Maytag washer & dryers for 40 years. Have always been satisfied until now. The first 2 sets of washer & dryer were great. Very little ever went wrong. Now I have purchased another set approx. 3 years ago. As of today, I will be putting approx. $300.00 in repair to the washer. Repairman said it is a bad design. It is the second time for the same problem, which was repaired a year ago! I will not buy another Maytag product if they cannot be reliable. I should not have to pay $300.00 in repair for a 3 year old washing machine. I am very disappointed.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

My model has 2 ovens which I love. A smaller one & a regular sized one. It also has a cooktop. The cooktop always has “marks” on it from the pots & pans. No matter how careful we are, the pots leave marks. We even bought new pots & they leave marks. Something that we do like is that 2 of the burners have “select a size” so these burners can be used for small or larger pots.

This is the loudest washing machine Ive ever had!!! I ask the installer if it was suppose to be so loud & he said yes. The machines sounds like metal scraping metal when its washing the clothes.

I purchased the Maytag Bravos MCT HE washer in 2011. Its about 3 1/2 years old and there was a very loud noise when the washer went into the spin cycle. Called the repair man and they told me the bearing and spin basket needed replaced. I had always had Kenmores with very little issues and they lasted for 12 years plus each. I get the HE model from Maytag and cant even go 3 1/2 years without some major issue. I called Maytag (Whirlpool) to complain and they said there wasnt anything they could do. I reminded them that I had checked for recalls on this model and looked into some of the complaints about this washer and that there were many of the same issues that I had plus many others. I felt like there should have been a recall on the bearing since they are going out too soon for this kind of a washer. I guess the Maytag repair man is now busier than ever since I dont see them on any advertisements anymore. Well, I will never buy a Maytag or Whirlpool appliance again after this.

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

Having had a household for over 40 years we have had a few washers come and go. I hate to say it but this line of washers should go. Worst pile of junk parts I have seen. Bought it from Costco a few years ago based on past histories of Maytags. Was I ever so wrong. It has never worked well. I chalked it up to being Water Efficient but after reading over 8 pages of scornful reviews, I was mistaken. Water level is always too low to do anything so clothes are needing rewashed. Have reverted to using the Bulky setting to do general washing as that fills the tub about 1/4 of the way. Then the spin cycles stops due to unbalanced load and loud banging of the wash drum, EVERY LOAD!!! And now for the past month Code DL pops up saying it is taking too long to drain. I have checked all hoses for blockages, none seen. And with the glass top, you can SEE the washer NOT WORKING right. We have a door on the laundry room and even with it closed the volume is over 70 dB and can overpower most conversations in our family room 20 feet away. I have been told that Costco may take it back but why punish Costco members for a design failure of Maytag??? Has anyone thought about a Class Action Lawsuit? The Bravos Quiet Series 400 dryer match to this washer has so far been flawless. I may have to dig the 20 year old Whirlpool washer out of the storage shed to replace this Maytag. Sad. I want to state my true feelings but I will not use profanity here.

I purchased a Maytag MDB7749AWW dishwasher in March of 2012. The electronic control on this unit failed in June of 2013 (3 months out of warranty). I have been trying to get a replacement part for over a month; the part is on backorder and unavailable. Whirlpool is unable to tell me when the part will be available. So, I have had no dishwasher for over a month and have no idea when, or if it will be repairable. Additionally this part is $150.00 and another $75.00 to have it changed. So it is going to cost me $225.00 to repair a 15 month old dishwasher that I paid $450.00 for. I have received ZERO support from Whirlpool. They told me today, 7-31-13, that the part is still unavailable and they will notify me in 3-6 business days as to if they can find a part. After seeing all the issues other people have had with this part, Whirlpools total lack of concern or support for the consumer and the cost issue it makes no sense to repair this unit only to see it fail again in a year or so. Basically I have a $450.00 boat anchor. The retailer purchased it from feels bad and is offering me another manufactures machine at a reduced price. Maytag has refused to do anything for me. I will never buy another Whirlpool / Maytag item again and I do intend to add my name to the pending class action suit.

After less than 3 years the interior lip of the machine is rusting. I found this when I was cleaning the interior of the machine because my white clothes were coming out with black soot on them. I can estimate that bleach was used in the dispenser 3-4 times tops over these 3 years. Very disappointed in the equipment. Ive submitted a complaint to Maytag with hopes of a favorable response. This should not be a warranty item...its defective design.

Bravos XL was costly. Mistake! I owned my first Maytag for 20 plus years. The sticker shock of buying a new Maytag 4 years ago was pushed aside knowing how long my previous model lasted. The salesperson at Lowes closed the deal with his explanation of an improved gear driven system vs the old belt and pulley version. Oh how wrong! I too have the jet plane from hell landing in my home for over 2 years now everytime the spin cycle engages. This is a two person family and it failed at 2 years?!?!?As for water conservation... if I dont include the additional rinse cycle, my clothes dont get clean. Watched the YouTube on how to repair this unit... but what guarantee do I have that it wont go back to the same problem in another year? Cant afford another big investment like this now that I am retired, so I will run this baby until it seizes up. Dont wash clothes if company is coming or if you want to enjoy evening TV programs. Not sure why this unit hasnt been recalled based on all the complaints I have read on this site?? Worst decision I ever made! I bet the Maytag Repairman is spinning in his grave!

Machine is very loud. Clothes do not feel completely clean when wash cycle has finished. I have a sense that not all soap has been removed. Dark clothes have streaks of white residue. Must turn clothes inside out before washing. Very disappointed.

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

I have read all the complaints. I have similar issues with Maytag Bravos. I’m frustrated that modern tech products stink to high heaven, especially when we refer to clean clothes not being cleaned well. The specific issues I keep getting are the following: the LF codes appear and the cold water does not fill so that it wont rinse or drain. I have replaced the defective washers and that helped for one load. I refuse to fix it. Why throw good money out for the same bad product? I’m looking for a no bells and whistles washer or dryer that works. I have issues with the dryer, too. No more Maytag products in the future. Question: Who truly makes a good reliable product nowadays?

This is an awful product. I bought this product from Best Buy at the beginning of August 2018, and can no longer return it because it’s past their 14 day return policy. This washer does not wash clothes well. No matter what setting it’s on, clothes come out looking dirtier than prior to washing. Maytag should do what is right and refund customers for this worthless purchase.

I wrote the below to Maytag on their FaceBook page, of course havent heard anything back from them. Adding this on since I forgot about it, I have dogs and wash their blankets often, not that theyre dirty just for the dog smell. I have to wash them on the sanitize cycle which is an 1.5 hours long because if I use the normal cycle which is only 43 minutes they come out smelling exactly the same way they went in. I saw someone else post that their mothers front loader doesnt put in enough water so Im wondering if thats what happens to mine. So wish I would have checked the reviews before buying, thought I was getting a great washer buying Maytag.This is what I wrote on their FB page: I bought a Maytag front loading washer on 5/10/16 which was delivered and set up on 5/13/16. On Wednesday 10/19/16 it stopped working, so just over 5 months from the day it was installed. I called your company on 10/20/16 for repairs, they couldnt get here until today, 10/24, so 5 days with no washer. The customer service rep had all the details on what happened and Im sure passed them along to the repair company. He ran diagnostics, said it was the drain pump which was obvious even to me, but claimed to not have one with him even though they were in stock. Cant make it back until Wednesday, so two more days with no washer. He then proceeded to tell me that the dryer had to come off (stacked on top since the washer is a front loader) before he got back, that the warranty wouldnt cover two people coming out. So Im supposed to spend more money to hire someone to come out, take off the dryer and then pay them again to come back and put it back on. I called the customer service department again and was told they dont cover installation which stacking is. She said the warranty doesnt cover stacked units, as far as I can find that isnt stated in the warranty so please let me know where that is stated in writing. So I have a just over 5-month-old washer that needs repair already (bodes well for the future doesnt it??), will be without a washer for almost a week because the repairman didnt bring the most obvious part with him (maybe wanted to be paid for two calls?) and have to pay someone else for installation so it can be fixed. So wheres the Maytag man? I am not a happy customer and will be letting as many people know as possible. Ill be in the market for other new appliances soon, will sure as hell make sure theyre not made by Maytag, Whirlpool et all.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

I bought a Maytag Bravos top loader in Oct 2011. About a yr after having it, it started having problems. At the end of the cycle, theres still water in the tub and clothes are soaked. A couple of months after that, it started completely skipping the wash cycle, so the clothes would just sit in dirty water and do nothing. I called the small appliance co. I bought it from and by the time I get done paying a house call and parts, I might as well buy another one. I called Maytag because it seems theyre all having the same problem and at some point youd think they would be responsible for their product. They couldnt care less and the options they offered me were a joke!! Please, whatever you do, DO NOT BUY A MAYTAG because you will be on your own if anything goes wrong (unless you want to pay them the price of a new washer!!).

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

Before you purchase a Maytag washing machine...from anywhere (I got mine at Home Depot), think again. This machine doesnt wash clothes, it doesnt rinse clothing. What it does is takes forever to fill up the tub then it doesnt even come close to filling it to where all the clothing is covered for rinsing or washing, then it just stops and sits there for a few minutes (??) and then it proceeds to empty the tub and youre supposed to feel like your clothes were cleaned.Not in a million years will your clothing get cleaned in a Maytag washing machine. Youve been warned...dont waste your money. Go to a used appliance shop, but the best one they have that does NOT have the Govt. regs built into it, and be happy you saved as much money and did NOT have to go through all the frustration and hassle everyone else has that bought a new Maytag washing machine.

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

My five year old refrigerator freezer was leaking due to a corner filler part left in the the freezer compartment that lodged over the drain hole in the freezer. It cost me $232.90 to have a repair technician dig it out. MAYTAG accepts no responsibility for poor inspection, workmanship or quality control and they will not reimburse my fee.

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.

In December of 2013 I purchased a Maytag clothes dryer model Neptune. In July of 2014, I was hearing a banging sound as the drum rotated. As a mechanical inclined person that I am I removed the top of the dryer and turned the drum by hand. As I turned the drum I noticed that the stainless steel crimped bead around the drum had separated just enough to hit the side wall of the dryer. I was able to bang down the raised portion of the raised bead. This was a quick fix and there was no more banging as the drum turned around. Then in June of this month it started to make that banging sound again. So I removed the top of the dryer and discovered that the bead separated again and then there was a crack that spread to about 1 1/2 inches. I banged down the raised portion again and this lasted for 2 weeks. That’s when I noticed that the crack spread further apart and actually ripped a hole in the left side wall of the machine and froze in position where it would not turn at all. So I reversed the turn of the drum by hand to allow the drum to turn again. At this point I decided to order a new drum which came to $264.00 which included shipping. When it arrives I will replace the entire drum. Being that Maytag/Whirlpool refused to honor their product because this issue happened after the warranty had just expired and the company didnt want to replace the drum. I have never heard of a dryer drum seal bead coming apart in all my experience with repairing an appliance. No I wouldnt suggest purchasing a Maytag/Whirlpool product to anyone. I feel the company should have done the right thing and replaced the drum. In life if you do the right thing all the time, then there would never be an issue with the consumer and corporation. Always do the right thing and you will never go wrong.

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!

First off I dont usually spend my time writing complaints; however, I feel Maytag is deserving of my complaint. Purchased dishwasher Model #mdbh979sab1 in 2013 and days before the 1-year warranty was up the front control panel quit responding, rendering the appliance useless. Got that fixed under warranty. Now about 1 year later guess what... Its got the same problem. Began to read others post on this site and found that this is a common issue. One person posted that her dishwasher began to smoke and nearly caught her home on fire. Maytag was kind enough to offer a paid service call and enrollment into their extended warranty program. I think Ill cut the umbilical cord on this one and go get something more reliable and doesnt pose a potential fire hazard.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

My husband and I purchased a Maytag stainless steel French door/freezer bottom ice making fridge from Hhgregg in Brown Deer, WI and 8 months later (now), Ive been told that my food that is spoiled, cant be replaced and my service for the fridge wont be done until next week! I have 5 kids and a husband. This has turned our world upside down. I called them and spoke to a Nicole and she said they cant do anything for us, but we can try to contact the diamond repair service at 269-927-2519 to see if they can get us in sooner. I asked for a refund for the fridge and she said no, the 10 warranty only counts for repairs... I am so angry that I didnt research Maytag before now. I gave the Whirlpool fridge to the delivery guys of Hhgregg and I had that for 18 years and it never went out on me. If anyone is reading this and is upset as well, let us get together and start a class action suit!