WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

You cannot go wrong with Maytag, even if there were issues they are reliable in repair, and parts are available so you arent forced to purchase new like some technology. I have been pleased with the front load washer dryer since 1998.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

We purchased a Maytag front load washing machine and dryer about 5 years ago. The front load washer is completely full of mold even though I have always followed the directions of wiping it out after each wash, leaving the door cracked, washing the machine with Affresh and even trying bleach and vinegar rinses. When I called customer service they refused to do anything about it. Then the dryer stopped working after 5 years and we had to get it serviced. Now, the door has completely come apart, as in every little piece has come off the handle and surrounding door frame. I have never seen anything like this on the oldest of machines and I have taken care of these appliances. I will never buy another Maytag...

I purchased this $900 Maytag washer from Home Depot in Oct. 2010. Now, after Ive just paid $129 for a service call through their designated repair service, I was informed it will cost $700 to fix this washer. I use the washer on average of three times a week. Its unbelievable that this type of crap is sold by Home Depot and that Maytag warranties will not cover repair as one year has passed.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

I purchased a Maytag Top Loader Washer MVWX500XL last May 2011 from Home Depot to replaced our 15-year old GE washing machine. Two weeks ago, it started making horrible noise like a jet engine taking off during spin cycle. I called in the Maytag repairman and was told that the bearing is gone and it will cost $ 493.00 to repair it. He claims that the damage is caused by not using HE detergent exclusively and he refused to leave us a written estimate. We are only three adults in our household and we do our laundry once or twice a week. For this machine to be repaired only after 2 1/2 years of light service and for almost the same cost as a new one, I will never buy another Maytag/Whirlpool products ever again and I will encourage everyone the same.

Purchase brand new range a couple of months ago. Self-clean oven does NOT self-clean and leaves weird, flakes of something that stick to oven floor. Burners are inconsistent and difficult to control heat level. Take forever to get warm, and then either boil over or wont get warm enough. Purchased this with inheritance from my mother - how sad! Always had such faith in Maytag.

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

Purchased MBF1958 model refrigerator July 2012. Has had 3 major problems. 2nd time the compressor has failed. For over 1 month have been playing phone tag and given the runaround by Maytag. Never return calls when promised and get a different story with each person I speak with. After 2 service calls to diagnose a bad compressor, $69 service fee, two weeks for the replacement to come in, the third serviceman decides this is not the problem and the refrigerator cannot be fixed. Maytag has once again offered to SELL me a replacement at a discounted price. Do I really want to subject myself to the HORRENDOUS MAYTAG EXPERIENCE again?

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

I will never buy another energy efficient washer again. My Bravos is supposed to save money and be environment friendly, but when you have to wash clothes more than once to get them clean, theres no savings. Ive tried different detergents, cleaned the washer, rinsed twice, added vinegar, baking soda and everything imaginable to get the clothes smelling fresh without any luck. I have had several items ruined because the bleach dispenser pours onto dry laundry. Im disgusted.

Purchased Maytag MDBH979AWW serial #FY4202009 from Lowes October 30, 2009. Control panel went out after warranty, and we replaced it. It quit working again in May 2012, and we replace the control panel, and then in November 2013 it quit and we replaced the control panel along with a new door latch just to be sure on December 4, 2013. The dishwasher quit working mid-cycle a couple of weeks ago only 9.5 months since we replaced the last control panel. Im fairly certain it is the control panel again. We have paid more to replace control panels for this dishwasher than we paid for the original appliance. There should be a recall and compensation on this issue. Very disappointed that Maytag and Whirlpool do not resolve this issue. We will be buying a different dishwasher, and it will not be Maytag or Whirlpool.

Maytag Range Precision Touch Control 800 Electric Smoothtop - The racks in the oven fall down. I have replaced them with new ones but am having the same problem. I emailed my concerns to Maytag a few months ago but didnt get any response (so perhaps I didnt go to the right site). The oven was purchased in early 2008 and this is the only problem I have had with it. If I am extremely careful, I can bake cookies but if I try baking or roasting anything heavy, the racks fall. It is very frustrating but I was pleased, for lack of a better word, to see that someone else was having the same problem - at least I know it isnt just me. I will try contacting Maytag again.

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

I purchased Maytag washer, as it was rated the best of the best at the store. First of all, Delicates cycle washes exactly like Normal. All my sweaters got ruined as the agitation is VERY HARD. I dont think the manufacture even knows what that cycle means! Absolutely awful! Theres no difference between Delicates and any other cycle!Second, Deep fill cycle. If you select off on that cycle the clothes get hardly damp. HOW can you wash hardly damp clothes???? If you go with Deep fill, the washer is supposed to weigh your laundry 1st and ONLY pour the water according to the weight. Well.... you can put only 5 small items and the washer fills all the way to the top! What the hell is this???? How can few items fill such a ginormous washer???? It doesnt work! Im so pissed and want this washer out of my laundry room!

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

A company who sells a washer that makes washcloths/towels smell musty as you take them clean from the drawer should be ashamed and refund everyones money!!! I have always love Maytag/Whirlpool products until this piece of trash washer. My husband, who is retired from Maytag, gets a very nice deal when buying their products under the VIP program. However, how nice a deal is it when you have musty/sour smelling towels after washing??? Ridiculous! Seems that when the washer went to no agitator and water/electricity saving they forgot what the purpose of a washing machine was. Im very upset and would NEVER recommend Whirlpool/Maytag products to ANYONE!

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

We purchased a high end Maytag Dishwasher from Lowes just 2 years ago. Within a year the machine was turning itself on, beeping for no reason, and eventually the functions on the control panel stopped working. When I called Lowes they gave me a number for a repairman who informed me that the cost of a new control panel would be $514 and its a known issue with moisture getting into the control panel. This is unacceptable. There are hundreds of complaints and a class action lawsuit regarding this issue and yet Maytag has done nothing to remedy this situation. I am forced to purchase a new dishwasher and I will never purchase another Maytag product.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

Im very pleased with both the washer and the dryer. The front-load washer is very efficient with many washing options dependent on items being washed. Spin cycle spins very well which lessens the dry time of the washer.

I purchased a MTW6600TB0 Washer and Dryer on 6/17/07. I have had issues with the washer from the beginning; smell in towels and mechanical problems as well. The machine does not fill properly and receive error codes that are electrical issues per A & E service. I get LF errors occasionally and randomly on different cycles. I finally called for service because I now am receiving F51 Error, which has to do with the basket per A & E service technician. I was told on Black Friday that my machine required both baskets and the rotary motor. My machine is just 4/5 years old. No unusual wear and tear. There are only three people in my family and we live in a fairly warm climate so no heavy winter clothing, etc. I was told that my stainless steel basket was rusting to my plastic basket. I am still trying to comprehend the fact that two materials that are not supposed to rust are rusting. After looking for a new washer over Thanksgiving weekend, I find out that Maytag warranties their stainless steel basket and rotary motors for 10 years. So do they warranty the things they say the warranty or not? Of course, it is a holiday weekend and I cannot get a hold of Maytag. I paid for a service call and the technician told me I would be responsible for the repairs at about $500 for parts plus labor. I looked up the parts he recommended replacing and it was over $800. I paid $1000 for this machine less than 5 years ago. Thats $200 a year for the privilege to use a Maytag. Additionally, my set is black. I can not find a black washer anywhere.

My Maytag Front Load Washer Model MHWE200XW purchased from Sears had a malfunctioning spin cycle. The authorized Maytag repairman from Landers, with support from a Maytag technician by phone, did not know how to repair it. The machine had light use over the past 15 months, and hence was not covered under warranty. So I am out $650 for the machine and $200 for the repair that resulted in continued and even worse malfunctioning. Unfortunately for me, the tests did not show any errors and the machine did not state any error. It just would not spin and then would not allow the door to open. It is a lemon and I do not recommend its purchase.

Ive had this Maytag for more than 15 years and it still works well. Its a basic fridge, no special features. Just keeps food cold or frozen. Freezer at top, fruit & veggie bins at bottom, cheese bin. No problems, good performance.

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

We purchased our Maytag Neptune Washer and Dryer approximately 5 years ago. Over the past year or so, Ive noticed an odor coming from our washer and it’s becoming stronger. Water is staying in the drum and there is mold growing on the rubber seal when you open the door.

I had a GE washer and dryer when I first moved to my new home - lasted 15 years. Then... bought a set of Maytag and they have both been the biggest pain in the world. Spent 3000 and Im ready to toss them after 3 years. Dont buy Maytag!!!

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

Rust on two year old Maytag Bravos washing machine - I noticed some rust along the inside lip of the washing machine lid and along the seam near the top of the machine about a week ago. I contacted Sears where we had purchased an extended service agreement. However, the agreement does not cover rust. I contacted Maytag and there is nothing that they can do either. The machine is kept inside the house in the laundry area. We have had two washers in the past 21 years that my husband and I have lived at this house that were much less expensive than the Maytag Bravo. They did not rust. This will be the last Maytag product we will purchase.

I bought a Maytag dishwasher, when I bought my house (7/2010). I live alone and I use my dishwasher only once a week or once every two weeks. After 3 years of working perfect, it stopped working. I had someone come look at it. After troubleshooting with the basic steps, making sure the water was correctly hooked up, a fuse was not the problem. The dishwasher door was shut completely. He took the racks and all movable parts, & thought something, a piece of glass, etc, was stuck in the drain. Nope. After reading these reviews I realize it is got to be the control panel because the start button will not come on and all these people have the similar problem. It just stopped. Period. The panel lights come on, but not the stop button. I am a single person as stated and on disability and on a very tight budget. I bought a Maytag because of the name and reputation. How long would it have lasted under normal use, say a family of 4, using it nightly? Certainly less than a year. I have no idea what to do now. I cannot afford a repairman, & I am certain it is the control panel on the dishwasher. I do of course have all the model numbers, etc & papers, when I bought it. I can provide proper paperwork, when contacted.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

I saw something on your website about Maytag Neptune class action suit back in late 2005. I have owned one, never was notified of the settlement, and saw this since I have a mildew problem also in my washer. They are not willing to do anything about the repair on my machine, but send out someone and make me pay for it. Since I bought it in 2002, I would want to know why was I not included in the repairs and why wont they honor me in this since I am the machines original owner. Help, I worry that I am not having clean clothes and it is contributing to illness due to mold spores!

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

This is the worst washing machine I have ever had in my life. Machine started bouncing during the wash cycle and also the spin stopped. Never in my life have I had a machine fail on me like this one. I spent a lot of money on this. This machine should be recalled. I read up on all the complaints. Its a model #Tw6600TQ0.

I bought a Maytag washer in Sept. 2018 because the company had a reputation of making quality products that did not need repairs. I was wrong. Because I live alone so at most I washed two loads a week, so the company cannot say it had been overused. After a little more than a year I notice at times the wash cycle took too long. One time I tried the 2 rinse cycle and it would not quit washing. A repairman reset the computer to factory settings (he was at the house repairing a refrigerator) and it worked for a few months trouble free before dying. I will not purchase another Whirlpool product since the company did not stand by its product.

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

I have an MSD2542VEB01 model refrigerator purchased slightly over two years ago. I have the same problem as many others, which is the plastic breaking on the shelves. The first time, it was within a year and the part was under warranty. It is now a year and a half later and one is broken beyond use and another is cracking again. Maytag refuses to help me as there is no “recall and the plastic is not available separately from the easily removable glass of the shelf. The least expensive price that I can find for the shelf is $107 and I need two of them. $214 (plus shipping) when all I need is two pieces of plastic? Be very careful when selecting your appliances.

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

We bought a Maytag dryer and within two years the drum cracked. It will cost over $500 to repair it and then will the new drum be better? I bet not. Piece of junk.

Love my Maytag washer! It is great to have a clear lid so I can see the clothes being washed. Not only the features, it really cleans my clothes. I was surprised at the stains that are removed just from washing them!

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

I bought the Centennial top load washer and the dryer in May 2016 at Lowes. They are junk. I had a secondhand Craigslist Maytag washer that lasted 7 yrs and it was still running just fine when I got rid of it after purchasing this HE junk. The flimsy plastic door handle on the dryer fell off about 6 months ago. The clerk at Lowes assured me that the washer was high capacity & could handle heavy loads. Now I cant wash heavy loads because the agitator is already loose and getting ready to break. I have to wash smaller loads on the hand wash cycle. I cant wash my comforter or my rugs. The real kicker is I cant reach Maytag! I have tried calling to sit on hold for 30 mins to an hour. I tried the live chat during their regular business hours and it was not open. I am so disappointed in these machines. This is the first time I have ever purchased a new washer and dryer and this is what I get. I might as well have set $850 on fire. DO NOT BUY NEW MAYTAG MACHINES. THEY ARE JUNK.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

I purchased my first and last Maytag double door bottom freezer in Aug 2018. The ice maker shoots ice out all over the floor, only half make it into the glass. It also sounds as though ice is falling down inside door. I had the ice maker replaced twice, the gasket as well, the back removed to check for water line blockage NO avail. Before the first ice maker replacement it sounded like a freight train. I questioned whether I had received a store second from Home Depot or a return as the stickers inside had been removed but HD couldn’t assist and Maytag didn’t care. Definitely NOT worth the 2000 I paid.

After one year, this famous Neptune washing machine began to sound so noisy during the spin cycle that neighbors must have thought a 747 was taking off from our house. After researching the web, I found that the main bearing always fails in this machine and there is a new one-man repair industry started up across the US to just replace these bearings. In fact, someone invented a bearing puller just for this problem. I am deeply disappointed that a once fine company would knowingly put out such trash. I am replacing ours with another brand, even though we have used Maytag for 30 years. Customers always determine who wins and who loses in the long run. Bye, Maytag!

Called Maytag to set up service call at around 9am for my washer, was given a rate of $129.00. Thought it was High but it was my only off day and felt confident that it would be a reputable company. If Maytag Priority Service would refer A&E Factory Service to me for service they must be a reputable company. I was sadly disappointed after numerous calls to A&E Factory service, a 5 hour window was not met and they were not concerned other than they would document it. Then I find out that A&E Factory Service has a Rating of 1 1/2 Star rating out of 5 and thousands of complaints to BBB and Consumer Affairs, dropped by Lowes for horrible customer service but Maytag Priority Service recommends them to service their product, says Volume on how Maytag takes care of their Valued customer after the sale. Maytag has lost a customer for life. A product without customer service and trust is nothing but a piece of metal!!!! I will be picking another Brand that doesnt use A&E. Maytag you have lost my trust and you cant buy that back.

We bought a Maytag dishwasher on 9/22/2012. Model number MDB7759SAB. Within the past couple of months, it has been very temperamental. The control panel started beeping continuously and some of the functions wouldnt work anymore while others continued to work too well; in that the dishwasher on occasion would rewash several times without anyone starting the machine again. The dishwasher also started leaking water... As of yesterday, the dishwasher control panel stopped responding and then out of the blue, the dishwasher turned itself on in the middle of the night! We called customer service and they said they could send a repairman out for around $89 and then we would have to pay for the parts needed and the cost of labor. After reading many reviews sounding exactly the same as mine, my husband and I are against repairing this lousy machine. Its absolutely ridiculous for a dishwasher to quit unexpectedly like this. Our question now is, which brand to purchase for our next dishwasher? No more junk please!!

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

We purchased a Maytag Bravos Washer and companion dryer in March 2018. I like to wash our king size bedding often and liked that this model had no agitator and could accompany the large loads. I am using the extra rinse constantly since I dont trust the amount of water (not) used. The dryer however, is worthless! No matter the garment or setting, everything comes out in a ball. Tshirts are twisted and wrinkled and half wet. I end up rewashing almost everything then being a guardian for the dryer---checking and rechecking every load. Maytag says sorry, its out of warranty. I absolutely hate these appliances!

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

I purchased the Bravos Washer and Dryer from an elderly couple who didnt have it more than 6 months. About a year went by and the washer started making a noise when the water extracted and finally flooded my laundry room. I found that a penny had gotten into the plastic housing that extracts the water. This has happened on 2 different occasions. I have replaced the extraction unit 2 times and it now cracked again. Then I started getting F1 error codes and having to restart as much as 6 times so it would start the cycle. This washer has been a royal pain. It is frustrating when you think you are getting a quality product and have nothing but problems. I previously had a Kenmore washer and dryer that lasted me 15 years and was still functioning when we sold the set after buying the Maytag Monster. We only ever replaced the heating element in the dryer once. That was it. I will not consider a Maytag again and possibly not another HE at all. Glad I did not buy them new!

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

Purchased washer in 2015, worked pretty good for 4 years. In 2019 belt, support rods, and control board replaced. In 2020 clutch, pulleys, and suspension replaced, waiting for service technician to replace transmission later this week. I purchased extended warranty thru Lowes, glad I did as the machine literally jumps in the air during spin cycle. Lowes stated I needed 4 repair visits to place a claim for replacement! Machine will not spin properly on high speed. Luckily I have a spare machine in the garage to use while I waited for repairs to be made. However, nothing seems to be correcting the problem. Very disappointed in the Maytag washer.

I ordered my dream refrigerator (Maytag Model MFT2776FEZ) on 05-12-2017. I had to wait 4 weeks for it to arrive because it was on back-order. I was willing to wait. All was good for 6 months. January 2018, the six month old refrigerator quit cooling. It took 2 1/2 from the service call until the part came in to fix before I could use my refrigerator again. I lost all my food. The same thing happened again in March 2018 except that it took 4 weeks for the part to come in once the serviceman ordered it. I lost all my food for a second time. February 2019, the same thing happened again. I placed the service call on 01-31-2019 for service, but the tech could not come out until 2/6/19. The part had to be ordered and could not be installed until 2-28-2019. For the 3rd time, Ive lost my food. My best friend that has appliances that are nearly 30 years old. She was going to replace all of hers and get exactly what I ordered. She has changed her mind and has decided she would rather keep her outdated appliances because they work.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

THIS PRODUCT IS CRAP!!!! I spend $699.00 at Home Depot, after 1/12 years the console stopped working. Maytags engineering staff should be fired!!! You stole my hard earned money. NOT once, but on a washing machine as well. I will never buy a Maytag product again. HEY NO WONDER THE REPAIR man sits on his ** the rest of the company does too! I dont have 250.00 dollars to fix this thing. Shame on your company. No wonder you dont want anything. DONT BUY MAYTAG, buyer beware. I am angry but this is not **!

I bought this electric dryer Bravos (Model# MEDB850YW0) in Nov. 2011. Since I bought it, its giving me the same problem - it doesnt want to turn on. Today is the 6th time that I have been calling the customer service to fix it. Yesterday, it just got fixed; and today, its not working again for the same problem. I asked them if they can give me a new one, since its not even over 1 year. But they said they will not replace it because it cant be fixed. But it is so ridiculous, and its wasting my time. This is so unfair. I paid $800.00 for this machine.

I purchase my Maytag Side by Side Refrigerator back in 2006 New. I purchase a Maytag based on the supposedly quality of their Products. And I have stove, and dishwasher as well. A week ago, after purchasing groceries, and made it home. The Refrigerator had gone out. I tried calling Maytag without success and broke down and called sears repair to come out. Well they made it today, and I was informed the Compressor had gone out, and would cost me $998.00 to repair. Of course I told him to get out of my home, because at that price I could purchase a new one. And you can bet it want be a Maytag ever again. I am so disappointed in their claims of being the best. Hype!!!

Maytag wont fix new washer. Service person came 3X, but it still wont go to rinse cycle. Last 2X Maytag said service scheduled, but no one showed. MT mgr said cant help & to just keep calling back.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

Used my washer ONE time and when the load was done my clothes were soaking wet. Tried to get the clothes to spin dry but the washer would not work. Called for repair. They replaced the activator. I did one load of laundry. It worked fine. Did a second load of laundry and the clothes were soaking wet. The washer would not do anything else.

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

Maytag Bravo washer and dryer purchased April 2011. Dryer works fine and am pleased with results. Washer does not clean simple dirt and stains off clothing. Washer never fills to a water level that covers all the clothing. Some clothing never gets submerged, thus simple stains never get water contact throughout the cycle. I now spend more money purchasing spray stain removers and using the heavy duty cycles and extra rinses, would have been better off getting a Kenmore with an agitator. The concept does not work.

Purchased a Maytag Bravos washer model MTW6700TQ ON 5/5/2008. Also purchased extended service agreement. This washing machine was only five years old when it started rusting on the top of the body where you load the clothes and fill the detergent. Not in a million years did I expect a washing machine to be rust-prone. Its a washing machine. The service contract doesnt cover dust, mold, rodent damage, and RUST (like rust is an external source). When I called Maytag they were not surprised. They said the life expectancy of their product could be as little as a year and a half. Regardless of the extended maintenance expense I now must throw this piece of junk away. NEVER BUY A MAYTAG. This time I am buying an LG.

I have a warranty on my Maytag refrigerator. My icemaker has been broken for six months. I have had repair people show up frequently to try and fix it. Six months and six icemakers later, it still cant be fixed. Remember, I take off work to meet these repair people who sometimes show and sometimes dont. They elevated it to the manufacturer who was going to come out and look at it on Friday, November 23 between 8 and 12. (This is day after Thanksgiving is my only day off.) He doesnt show up nor does he call. So, I called and he is running behind. I should wait until he gets here. Evidently, he doesnt have a phone. These people are totally disrespectful of other peoples time. I didnt mind waiting for it to be fixed but I do mind people who have no consideration or respect for other peoples time.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

This dishwasher is at 10 years old, but is a real workhorse. This machine cleans like no other! Never worry about our dishes being clean. But we have replaced the seal once.

3 years ago, we purchased all new Maytag appliances for our home. Within one year, we had issues with the top load refrigerator getting warm and the bottom load freezer getting extremely cold. After calling Maytag and getting horrible customer service (long wait on the phone, no supportive/suggestive advice, rude representative), we were given a phone number for a local Maytag repair man who charged $300 just to walk into the house.He was literally in and then out of our house within 10 minutes. His advice was to unplug and defrost the refrigerator for 24 hours. Thankfully, his suggestion worked, but should have been given to us as a troubleshooter by the representative on the phone with Maytag.We have had to unplug and defrost the refrigerator about every 3 weeks since. It has become very annoying and stressful. There is obviously a defect in the refrigerator that should be replaced by Maytag! I will never buy a Maytag product again.

I bought a Maytag dishwasher, model MDB8551AWB, in 2007 and have kept purchasing maintenance agreements. From January 2011 to March 2012, I have had to have Maytag send out a repairman to replace the control panel five times. This is absolutely ridiculous, and the inconvenience. Plus the repairmen are surprised Maytag keeps on repairing this dishwasher and not replacing it. More the $2000 has been put into this dishwasher since January 2011. When calling Maytag, I was informed that the problem would have to be the same which it has been but on the same contract for it to be classified as a lemon. Well, it has now been four times. I will never purchase another Maytag.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

3 years into the buying of a Maytag Bravos XL MCT washing machine (Serial # **) and already had to replace the original control panel for a cost of $400+ in less than 2 years of the buy. Now AGAIN the replaced control panel is now once again shot and the machine is not starting. The appliance needs to have a #manufacturers recall for the control panel. #Maytag #Whirpool #BetterBusinessBureau Note -- all existing customers, please lodge manufacturers complaint for the control panel issues @ 1-800-344-1274. (Even if you dont pay because of extended warranty or plan coverage, if you are facing the control panel issue year on year). All future customers, buy this appliance at your own risk.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

Once again I purchased a maytag appliance. I was hesitant because of poor past experience. I bought a refrigerator, lasted 3 years, and a stove, a little better 4 years. When I went to buy a dishwasher at home depot, they assured me that maytag had improved their standards and now were more conscious of maintaining the quality of their products. Long story short, I bought the dishwasher in april of 2015 and now in october of 2015 the control panel is shut. I have requested a repair, but find this unacceptable as the life of appliances seems short at best. I am fearful this could be on going as I now am reading the customer reviews, and 90% of them have had this trouble more than once.

The microwave is 5 years 6 months since purchase model MMV4203DS. Fire started at rack clip left front rack, was cooking bacon. Called Maytag and according to them and manual on page 3 is only for 2-level cooking to avoid damage to microwave oven. DOES NOT SAY WILL CATCH FIRE OR THE RACK CAUSES SPARKS AND BACON SHOULD NOT BE COOKED IN A MAYTAG MICROWAVE. But according to Representatives of MAYTAG ** its my fault for not reading my manual. YES AND NOT HAVING THE SERIAL NUMBER THAT IS ON A PAPER TAG IN THE WHIP ZONE. The was gone from keeping it clean faded out. So I cannot be helped without the model and serial number.

I purchased a new Maytag top loader at Home Depot. They delivered and set up. From the first load, I have had problems with the washer stopping and jerking. Clothing becomes a tangled mess. I contacted Maytag, they suggested I make sure I put on proper setting for the items within the washer. I do not know how one can fail at putting sheets in the washer and putting the setting on sheets and they are so twisted you have to spend time pulling them apart. This happens to almost everything I wash. I believe that I have a lemon, still under warranty, Maytag believes I should pay for a house call. Home Depot will only forward the information to me that Maytag gives to them.

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

This has to be the biggest joke in the world for the respected name of Maytag! The engineers that developed this worst-of-all machines on the market must have been circumcised with pinking shears. 80 minutes for a wash cycle? Even rapid wash takes an hour of slowly spinning and spinning ad nauseam with almost no water. The clothes sit in the same position even on the very brief agitation cycle... Nope, the clothes do not come out clean, although if you add bleach to the dispenser, since there is no water in the tank, the bleach does triple duty and rots the clothes. Is this masquerading as energy efficient when all of the cycles are an hour long, about? Unfortunately it takes water to clean clothes and the environ-lack-of-mentalists must have bribed Maytag to develop the worst washer on the planet. Absolutely!

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!