Purchased this Maytag dishwasher from a local Home Depot in Feb. 2014, no problems until now in late July 2015 (about 18 months). The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond.Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, can not be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only about three days ago. I assumed user error so let that cycle run, then was able to choose a different cycle (cant remember which one) which also completed. But since then the control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem, so will probably replace (with something other than Maytag) rather than repair.

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.

Leaking water and puddles in front (each side) of refrigerator. Purchased from Home Depot on 12-20-2011... After doing a search on the internet I found that this is a common problem with the Maytag refrigerator. This model is a two door with ice maker on left door and freezer on bottom of unit. Looks like Maytag does not want to be bothered with my problem. Model #MF12569YEW. It certainly was not an inexpensive model. Whatever happened to the Maytag repairman who was never needed because the Maytag products were so great???Updated on 03/21/2015This is not the first time this Maytag product had problems. Expensive piece of junk in my book! First, as many consumers have experienced there was water leaking in front of the refrigerator onto our hardwood floor. Now the door gasket seal ripped on the end tabs. What happened to Maytag?

We used to own a Neptune Model. After always leaving the door opened and following the recommended monthly cleaning and many extra cleanings with diluted bleach and water, we could not get the smell out. We paid for a new seal, Advice from Washing Machine Repair service even though we paid a lot for an extended warranty. We had to pay for this ourselves. We also had our year to year maintenance. Because we could not fix the issue, nor would MAYTAG, we donated the set to donated it to Salvation Army.We decided to give MAYTAG another chance, so we purchased a brand new FRONT-LOAD WASHER and DRYER in 2014. As I would repeat the same regiment, I would notice little black specks, so I would clean it an extra time with Afresh. I have continued to this date, repeating the same regiment of keeping my washer clean and serviced as we should, I now have the whole tray dispenser spotted with LARGE black goo that smells. So I have continued to clean my Washer.After returning home from the Cleveland Clinic, I was ready to do our laundry from the trip, more black goo and smell coming from my Maytag front-load washer. My sister had stayed with my 86 year old mother and had wash a load of towels while we were gone. She left the door opened also as she was instructed many times, and that is how we found it. So I took the dispenser tray out as usual and bleached it and scrubbed it. As I did this I noticed bigger areas of goo. I looked in the dispenser housing and OMG it was covered with black mold. I am appalled that our $900.00 Washing Machine is like this. This IS BLACK MOLD, There is no way to remove this mold. I have the sides and bottom cleaned with bleach, BUT I cannot get into the multiple crevices.I called Maytag and I was initially told by a Maytag Customer Service Person said that it sounds like BLACK MOLD and MAYTAG COULD DO NOTHING! I asked to speak with a supervisor. At first she seemed a little put off, but as we talked she became more pleasant, I offered to send pictures or a video of the WASHER WITH THE BLACK MOLD and she said no. She told me to pour bleach into each dispensing compartment and the drum. Then run a wash with no clothes on all HOT WATER 2 times, then rinse 2 times and this should get rid of it and to also leave the dispenser drawer open a crack as well as the door after each wash.The Supervisor said ok and thanked her for her help. Then she said good luck and thanks for calling MAYTAG. Ive did and already do everything our Washer manual says to do on cleaning and maintenance of my expensive Maytag Washer and dryer. The manual says nothing about leaving the dispenser drawer open a little so it dries. The bottom of the housing looks great from doing this, along with me scrubbing it until 5:00 am with diluted bleach water. However, in the MANY SEAMS, CREVICES, THE SCHUTE AND POSSIBLY THROUGHOUT THE WASHING MACHINE IS BLACK MOLD that we cannot access without disassembling the machine and voiding our extended warranty.MOLD GROWS RAPIDLY and causes many illness. I already have an ongoing illness since childhood, I take care of my 86 year old mother, my husband just finished cancer treatment in January. We certainly do not need any other health issues. I called my local Appliance repair company and they said that they normally do not handle anything like this, but if my husband couldnt take the outside of the machine off then the top I could pay for a repair person to come out to take it apart then call and have them come back to put it back, pay them again to reassemble our Washer.I believe Whirlpool in its purchase of Maytag has taken a Monkey on its back. Maytag will do nothing, why should they? They already have their money from when we purchased our machines along with money from many other consumers who also have ongoing issues with their WHIRLPOOL/MAYTAG Front-Load washing machines. It is undignified and deceitful how they treat their consumers with such disregard when we have filled their pockets by being loyal customers.Word of mouth is good or bad advertisement for any company. Everyone who has unresolved issues of any kind can write a formal complaint to the CEO and President of Whirlpool/Maytag. The address is on the internet. Shame on Whirlpool/Maytag for taking many consumers hard earned money, when apparently some of Whirlpool/Maytags money is ill gained by developing and manufacturing a consumer product that causes black mold and marketing it to sell to us, the consumer. THIS IS A SERIOUS ISSUE WHIRLPOOL/MAYTAG. OWN UP!!! My advertisement begins today!!!

I have filed a class action lawsuit against Whirlpool for their faulty control panels in their Whirlpool and Maytag dishwashers. Please contact my attorney, Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 and let them know if you own or owned a dishwasher with control panel failures.

We purchased a Maytag front load washer and matching dryer in 2007. In 2010, the main control board of the washer broke down. We spent $450 to replace it.In 2014, the washer stopped working. The dryer started producing horrid odor when we used it. We replaced both with LG recently. We NEVER buy or recommend Maytag products. Stay away from Maytag. There are many other reliable washers and dryers in the market. This is to help other consumers.

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

I, too, have had a lousy experience with this washer – it does not correctly sense the amount of clothing in the load, and often fails to get everything wet. Once the cycle starts, it does not necessarily pull everything into the water. You must ball each item up around the center or have sleeves and legs of clothing end up very twisted. Clothing is often very wrinkled and I do not feel that enough water is used to achieve clean clothes. I did get a good response from Maytag, who sent a repairman free of charge after the one year warranty period. He was very gruff and condescending – implying that I am buying the wrong kind of clothing. He reset the washer which improved the water levels, but now it is back to its old tricks. Hate, hate, hate this washer. Now it is failing to start unless lid is slammed shut! May get a new one in a black Friday deal, but have to figure out how to ditch this one while retaining my integrity/honesty to buyer.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

Was very happy with choice when it arrived. Bought October of 2010. Now, this summer, nothing but problems. Honestly weekly cleaning of vents underneath, sheets of ice in freezer, refrigerator not staying cool, constant frost plugging areas, and no more ideas of how to make it work. I already quit with Kenmore after terrible problems with their appliances and now when Maytag doesnt stand up for years what are we supposed to buy? OUTRAGED with American quality of products and disposables. UGH!!!

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

We bought a Maytag range Nov 2013. My daughter has maytag appliance and stand by maytag. We grew up with maytag. But those days are no longer. It is not about quality, it is about how many did we make, how many did we sell. I am very disappointed with my range. I tried several times to use my upper oven, in disbelief my lower oven was heating. This happened so much that I touch to make sure that the Correct oven is on. I also have problems with my knobs for my burners. I could not turn off burner after finished cooking. We had to unplug range and turn off gas, if we did not do that the burner would have remain burning. This very uncomfortable for us.I still believe in maytag. I am sure we have not talk to the right person. There is too much at stake for the company, too many complaints are bad for any business. I too am a victim, very disappointed, I wont give up. I have a warranty with home depot and they have been great. It is not their product but they sold it. I hope everyone with a lemon will get problems solved. We only want what we pay for, even manufacturer when they buy other products they want quality as well, we all do. Hoping everyone will be able to get justice. Thank you.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

French door always has freezer closing problems. Whenever the freezer is not closed tight, the bottom will form ice block, and freezer doesnt close. I have extended warranty but the repair people do not give quick appointment. I sick of this product.

We had perfectly working 20 year old top loading white Whirlpools w/ an agitator, when we remodeled our home and wanted new pretty grey appliances and decided to donate our machines to the church. I chose Maytag top loading due to their former reputation we experienced with dishwashers, etc. It had an agitator, deep fill option, extra rinse, etc. The sales person at Home Depot stated, the agitator is because people like you still want the agitator, and the deep fill will give you the water you have been used to. Not so at all!!Clothes get wound up together, even with filling the wash tub in bundles, there is almost NO water to thoroughly clean & the rinse cycle is a joke. Clothes do NOT come out clean. Im 58 yrs. old and have been doing laundry since I was 13 so I know what I am doing. Its just my husband and I now, and he is so upset that his clothes are pilling probably from rubbing together, even though I occasionally use laundry bags. I seriously wish I would have saved my money and kept the 2 perfectly working whirlpool units I had. This has been such a disappointment. I sincerely would not buy these.P.S. Weve had service out at least 5 times in the last year, and all they do is test the washer and tell us its working as intended... The last thing that is going to happen is we are going to get refunded for a different set, even though we were educated over and over what it would do by Home Depot associates. We are heartbroken. Maytag is going to lose their former reputation on these washers a dryers :( There is simply not enough water to clean or rinse things!

We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

I installed a new Maytag Wall Oven Microwave Combo 18 months ago. I had not used the microwave in over a week. Last night, we heard a loud pop and realized the beauty glass front on the microwave had shattered. No one had closed the door too hard, in fact, we had not used it. I see where others have had this problem.

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

Purchased my 1st brand new washing machine almost 3 years ago, a Maytag Centennial Washer for a little more than $600.00. Now it needs over $400.00 worth of repairs to get it working. Theres a reason the Maytag repair guy has nothing to do. Its because their products cant be repaired and are disposable. 25 years ago we bought our first washing machine that was used. It lasted for 22 years before it died. Maytag cant make a product that can last for 3. Also got stuck with a $65.00 service fee for them to tell me its broke and not worth fixing. Do yourself a favor and steer clear of their products.

Paint bubbling & peeling off appliance: I purchased new double convection oven from Lows (Maytag). One month after delivery, paint began to bubble and peel off. Maytag takes the position that as long as the oven functions properly, the paint is simply cosmetic and the warranty does not cover cosmetic problems. Maytags position is that even if all the paint peels off but the appliance still functions properly, too bad for you!

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

We bought our Maytag washer and dryer a bit over 5 years ago. Now the UL warning comes on. Found out it will be over $400 to fix it. It only cost $500 new. Repairman says it is very common and not to pay him to fix it. Our GE went 20 years. Lesson learned, wife is out looking at new GE.

I have never reviewed anything and feel compelled to chime in. The Maytag Bravos XL is the WORST washer dryer set ever. My 20 year old tiny washer with agitator cleaned a million times better in half the time. In fact this washer doesnt even clean your clothes! The reason is because so little water comes in and you cannot manually control the amount of water. Ive tried deep water wash-total joke. Heavy duty wash and extra rinse, still no better. You can wash it 2-3 times with the same poor results. Who wants to put on dirty underwear! The dryer easily takes 2 cycles to get an average size load dry and forget sheets and towels! They take 2 hours.

We purchased our Maytag dishwasher from Nebraska Furniture Mart in February 2013. The touch panel on our Maytag dishwasher quit working in December 2014, several lights would come on or flash or not work at all. The first repairman that we had come out took the panel apart, cleaned it up and put it back together ($100). It started working again but a few days later it started doing the same thing again. So I called the repairman back and he said the touch panel would need to be replaced. He called all over Omaha and no one had the part in stock. He called the Chicago Maytag warehouse and was told by them that they were out of them because there were so many defective dishwashers that they used them all. Now they are trying to find a new manufacturer to make them. It could be months before they get them in. So I contacted Maytag and of course they said that is not true and put me through to a parts company that they said has all the parts available. When I told that company that it was the touch panel, I was told by them that you only replace the touch panel for cosmetic reasons! So we got a second opinion from another Maytag repair company and he spent about 10 minutes looking at the dishwasher and said its a defective touch panel. He said he has replaced a lot of them in Maytag dishwashers. He recommended that I contact Maytag customer service and try to get them to pay for the part. I did call them and of course they refused because it is out of warranty. The supervisor even told me that they have not had any complaints about the touchpad malfunctioning! They do not stand behind their products anymore. I will never buy a Maytag or Whirlpool product ever again. I told them exactly how I felt and their only reply was Im sorry you feel that way. I am surprised they continue to stay in business. I dont understand how major stores can continue to sell their products when they are garbage. Based on the other reviews Ive read, Im not even sure we should fix this for $250.

I bought a Maytag Bravos top loader washer and dryer less than 2 years ago. I started having problems with my dryer 3 months ago and after several service calls (and a few hundred dollars), it still does not dry our clothes. I spent over $1500 for the pair and was excited to have a top end washer and dryer. My biggest complaint is with the manufacturer, Maytag - they just dont seem to care. I did not buy the extended warranty for two reasons. First, I bought a nice unit and expect it to work properly for a reasonable amount of time (at least 4-5 years without any problems). Second, they are just a bad purchase and they cost about half of the unit and if you buy a nice unit, you shouldnt need one. I could have bought a new dryer for what I spent to try and have this one work properly. My wife and I spent $600 for our last set which lasted 7 years without a problem; they were manufactured by GE, which I now wish I would have bought another GE. My wife talked me into buying a new pair to accommodate the needs of our growing family. I wished I would have kept the GE pair that was working.I would not recommend any Maytag appliance: they really just dont care to provide any reasonable service to stand behind their products. What a shame. This reminds me of why many foreign manufacturers are beating us at what we used to do best - make products that last and work! The washer and dryer look nice and have many great features, but these dont matter much if they dont work.

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

We bought a top load washer and the matching dryer. A thermal switch (I think it’s called) blew in the dryer at about two years. Luckily my husband is an electrician, so he took care of that. WASHER-A little after 2 years the plastic “driver hub” stripped And the agitator has stopped working, the door is having trouble locking and it won’t spin fast enough to get the water out of the clothes. I’ve ordered a new “driver hub” for $53! It is a cheap plastic part. Probably 1 cent to make in China. Robbery. This will hopefully resolve all 3 issues I’m having with the washer. They even charged me 9.99 shipping. $2000 later Maytag/Whirlpool should treat their customers like royalty. I will never ever buy another Maytag or other brands associated with Whirlpool ever again.

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

I have a self cleaning Maytag electric stove. I discovered the self cleaning starts after so many times of using the oven. But the stove didnt give me warning of this when I put my Thanksgiving turkey in the oven. Halfway through cooking, the oven door locked and went into cleaning mode which scorched my turkey and could have possibly caused a house fire. Also, my top burners have a mind of their own, while cooking they turn up on their own. This stove is very dangerous.

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

I believe the Maytag Bravo washer and dryer was manufactured so the Maytag man would have something to do once again! Buyers Beware! My $800 washer broke down 1 week after warranty costing me $400 to repair!!! Half the cost of a new one... now the dryer is making horrible noises. I fear calling for repair... or should I just buy a new different one?? My last washer and dryer lasted 30 years!!! Bravo certainly did not have all the kinks out of them before marketing them! The cost is to the consumer who trusted the name! You cannot return a 2 year old appliance! The laundromat would have been less costly than this washer and dryer! Maytag should be made to recall these defective machines or at least repair for free. Do not buy!

The HE version of Maytag washer leaves the clothes smelling bad. There are suggestions to remedy this, but why do these type washers cause this? The suggestions dont work. No more HE washers of any brand.

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

My Maytag model MMV4205BAB microwave turns on and heats when the door is closed. We paid a lot of $$ for this overhead microwave and it has not been a satisfactory product. The turntable broke within a couple of months and now this. Im afraid it will burn my house down. This is a defective product and in my opinion it should be recalled. I have read several other posts about this exact model and problem. We purchased all Maytag appliances for our new home and we have had problems with all of them. The auger on the ice maker on the freezer broke within a couple of months. The handle on the oven door broke off while the builder was installing the appliances, and the top of the line dishwasher doesnt clean the dishes. It leave deposits on everything, no matter the detergent used. Ill never purchase Maytag again!

Started having problems summer 2017. My dishwasher leaked and tank replaced, followed by drain pump, followed by circuit board in 2017. Didn’t have use of it for months. It has started leaking again as of Sept. 17.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

Thanks for the other reviews about the control panel problems... I too have the same issue with the short circuit. My Maytag dishwasher mdb7749sam1 was installed in January 2013. I spent an hour on the phone and the chat... HERES THE SOLUTION: When I told them the machine started in the middle of the night on its own, it became a safety issue. I have all the same problems as everyone else, flashing lights, the washer does not properly respond to the input from the control panel... I was told that even though it was out of warranty, as a gesture of goodwill Maytag is sending out an authorized repair service to fix whatever is wrong at no cost to me at all... Tells me that there really is an underlying issue. Anyway best of luck to anyone else in the same boat. I rated them as a 3 - not happy that this machine failed and I wont buy another, but they seemed to jump on fixing it...

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

Maytag Model MDB7749SBW: Lights on control started flashing even when not it use, cycle lights varied, dishwasher would start on its own. Stopped at dealer and he said he never heard of problem. Checked online and found problem identified all over the internet. Called Maytag and they knew of problem and said they would send serviceman out to check. First trip free and parts would be free but I have to pay labor for second trip to repair. Dishwasher is just under 4 years old. Serial F31703877. Problem is corrosion on small flexible circuit at top of door. Same problem as others. Maytag states never been a recall!!! THIS CERTAINLY HAS THE POTENTIAL TO CAUSE A FIRE. Will never purchase another Maytag or Whirlpool appliance again. Poor quality and lies on the part of company and dealers as well.

Purchased a Maytag Dishwasher (Model MDB7749SBBO), total with tax $590.34 on 3/31/13. It wasnt a cheaper model, had stainless interior. Owning it after a 1-1/2 year, the Control Panel went bad. Maytag offered me for $267 for repairs and 1 yr warranty. Why thats about half the price I paid. My personal repairman told me the cost would be around $200 to replace the control panel. Why I could get a more inexpensive model for $300 and still get a year warranty. Very disappointed in Maytag quality of their product.

From the beginning, the blower motor (for the control panel? never needed one before) was too noisy. I just bought the oven from Lowe’s. They sent out a repairman. He replaced the motor, but has exactly the same level of noise. It is bad design/engineering. Im going to try some other brand. One problem is that you cant listen to the fan noise before you buy the oven and install it. And there are no decibel requirements or ratings. Industry regulations need improvement. Model MEW7527A, bought new in Dec. 2012.

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

My five year old refrigerator freezer was leaking due to a corner filler part left in the the freezer compartment that lodged over the drain hole in the freezer. It cost me $232.90 to have a repair technician dig it out. MAYTAG accepts no responsibility for poor inspection, workmanship or quality control and they will not reimburse my fee.

I bought this electric dryer Bravos (Model# MEDB850YW0) in Nov. 2011. Since I bought it, its giving me the same problem - it doesnt want to turn on. Today is the 6th time that I have been calling the customer service to fix it. Yesterday, it just got fixed; and today, its not working again for the same problem. I asked them if they can give me a new one, since its not even over 1 year. But they said they will not replace it because it cant be fixed. But it is so ridiculous, and its wasting my time. This is so unfair. I paid $800.00 for this machine.

We have had this refrigerator since January 2011. All was OK for 18 months. Then the lid to the deli drawer fell off, the plastic bar that holds the two drawers up broke (weve had to use roof shingles to prop them up) and another one of the plastic pieces crumbled. Now the ice maker wont work and the refrigerator makes a loud ticking noise. There are only two older adults here and we have not treated this appliance roughly. After reading all the complaints on this site, Im wondering if any of it is worth fixing. My GE refrigerator worked for almost 20 years.

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

Besides the fact that it barely agitates or turns over the clothes even on deep fill (which we need every time otherwise a whole HE cycle goes and the top clothes remain DRY), the oh-so-fancy power button stopped working at less than 2 yo! And guess what, because it is not a button or knob, but control panel sensor button you hover over to turn on, the fix is to replace the $400 little control panel box. On a $600 terrible washing machine! We trashed it and bought something else without a faulty button system. Very unhappy. Do not buy this.

I purchased our washer and dryer together in 2012. Now my washer is making a really bad sound on the spin cycle. I talked to Maytag in Tenn. and they wanted 130.00 just to show up. Plus 300 to 500 for the parts that was needed. Wow. I am retired and on a fix income. I called a local repairman in OkC. After telling him the brand of washer I had, he said he would not come out to fix it because of the money would be expensive. 300 to 500 dollars for parts. He said it would be cheaper for me to purchase a new one. This seems to be a real problem. I talked to Maytag supervisor and she could not wait for me to get off the phone. Nor would she give me her name. Buy Whirlpool!!!!!!!!

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

We bought a new dishwasher 2 years ago. Top of the line Maytag Model #MDB8959SBW3 $749 plus tax. We bought this one because they told us what a great 10 year warranty it had. Found out that is a lie. The only thing the 10 year warranty covers is the stainless steel tub, the racks and chopper blade. The stop button on the control panel (circuit board) quit working and the dishwasher wouldnt start. When I called Maytag they said So sorry. It broke so soon, but that is not covered.We were told by a repair shop that Maytag has had nothing but problems with their control panel and the control panel part alone is $150 plus tax plus installation. Our old Maytag lasted 13 years and was still running great, but needed to be replaced because the racks were rusting out. I wish I would have kept the old one. I will never buy Maytag again since it is now made by Whirlpool. If Maytag is having so many problems with their control panel, they should be recalling them.

We purchased a refrigerator in December 2013. It quit working less than 8 months later. The company contracted to repair it made us wait 4 days for service; they did not repair the unit. We are now expected to wait another 4 days for them to return. STAY AWAY from Maytag!!!

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

We purchased a new Maytag side-by-side refrigerator back in 2011 and for the last several months it has been leaking water into the bottom of the freezer unit when it goes through the automatic defrost process. The water freezes and after a few of these cycles causing the ice to accumulate and build up, it starts to leak out onto our kitchen floor. About every 10 days we have to open the freezer door, break up the accumulated ice on the bottom of the freezer and remove the ice chunks by hand. What a pain in the neck! Most of the time we can prevent the water from escaping, but not always. This is going to damage our kitchen floor, not to mention its a safety hazard for slip and falls, and/or fire or shock hazards. We have contacted Maytag directly, but nothing will be done as they say its beyond the 12 month standard warranty. They said one option is for us to purchase an extended warranty plan from them for only $359. Really? Are you kidding me?? They dont seem to care about a potential product liability property damage claim/suit, nor an exposure for a potential bodily injury claim. As Ive tried to explain, this is NOT a warranty situation, its a product defect situation and one probably worth a class action lawsuit based on the number of complaints Im aware of. They know its a product defect problem, but choose to ignore it at the expense of numerous innocent consumers. The only resolution seems to be filing your own lawsuit against them for some kind of remedy to this very aggravating situation that occurs every 10 days or so. Maytag used to be very good appliances, ones that were made of high quality materials, and lasted for years without any problems. Thats why I became a Maytag fan in the first place, but ever since they were purchased by Whirlpool Corporation, its not the same old Maytag we used to know and love. DO NOT BUY MAYTAG APPLIANCES - you will regret it!!

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

We have had and used this washing machine for over 25 years and only had one small problem and that was to replace the lid switch and the machine is working today as good as the day we bought it, it has went through raising four kids and many grandkids.

Magtag Bravos Washer top load Model MVWX700XW1 - I purchased my washer in June 2011 with the understanding that this was the best washer for my money and needs. I have family of 4, and laundry is a continual cycle at our home. I had the washer delivered and installed by the store where it was purchased. I was pleased with the machine even though the clothes were extremely wrinkled after each cycle, but the salesman was kind enough to tell me this would be so. 21 months into use, I had a water leak from the internal cold water valve. It’s not covered by warranty; I had the valve replaced. Within 2 weeks, the machine would not spin out the clothes; if it did, they were still wet, or would stop mid-spin cycle and start rinsing again. It took 2 hours to wash a 37 minute hand washables load this past Saturday, 4/6/2013, not to mention the other 4 hours washing to regular loads just to get the machine to rinse and spin. The service technician has spent the past 2 days at my home trying to repair my machine to tell me today that it is not the lid lock, but the master control panel which is still not covered under the manufacturer’s warranty. To say the least, I now have to purchase a new washer as I have invested $250.00 for a valve and the control panel is $275.55 plus labor.This machine is the biggest waste of money that I have ever spent. I have been a loyal Whirlpool customer having owned two other Whirlpool machines, each lasting 17-18 years each. I do not abuse my appliances, overload or in any other manner try to destroy a machine for personal gain. I do, however, feel that Whirlpool/Maytag needs to recall these washers or cover the parts beyond what is written. I have read numerous accounts of these and similar issues by others, yet the company will not stand behind their appliances. Really!

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

The machine runs and runs and runs and still the clothes come out dirty. Clothes are often not even wet all over. The Maytag HE water-saving washer is a terrible Hoax. The dryer also is faulty. It rolls the clothes into a big, undried ball of dirty clothes.

This is the WORSE POS I have ever owned/used/etc.... our clothes are dirty, w/ a scummy film, really bad in most cases. Some have weird stain appear that werent there. Electric & water bills up. Have to always use deep water wash, double rinse. My clothes are wet when I put them in due to sensor fill (extra weight), also a zillion mesh bags. Clothes are getting trashed, faded so bad & smell bad. Having to use a cleansing product monthly, in one aspect, should encourage the engineers that signed off on this POS to change careers. Maytag customer service says no complaints have been filed!!! Horse **!!! $ 800.00, trashed, unclean, wrinkled to the point of almost needing to iron all your clothes. I have been going to the laundromat. Engineers should have been FORCED to use this machine at least 2 months.... good reviews my **.

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

Just dont get clothes clean like the old agitators. Doesnt matter what brand you decide to get I guess. Had Samsung front loader before and was disappointed in that brand as well. Thought them both to be good buys... But miss my really washed clothes!

I purchased this washer in Oct. of 2017. From the beginning, it has not cleaned clothing properly and leaves a white residue on clothing. To get the residue off, I must wash the clothing again or sometimes it will come off in the dryer. The water level is too low to efficiently clean. I thought I would save water getting this but not at the price of multiple washes... What good is that? Since there is no agitator the clothes just sit at the bottom and move back and forth as one big clump, with just a few inches of water. I am sorry Ive waited so long since I am now past the point of returning this piece of junk.

Bought a Maytag front load washer and dryer, it rattled and shook from day 1, they have come out 3 times in 1 month to fix that, now it wont even spin. This will be the 4th day of work I have had to miss, and all they say is, We have to send someone out to repair. Sorry. Do not purchase their products!! They dont care.

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

Around three years ago, my wife and I bought a top loading Maytag washing machine. It worked fine at first but later on, my wife would constantly find socks at the bottom of the machine after the washing machine was done. The last straw was when another sock plugged up the pump and had to buy a new washing today on 12/29/15. My wife told me tonight that the serviceman told her that they were getting similar complaints from other people who were having that same problem with this particular washing machine made by Maytag. If I knew that Maytag knew that there was a problem with this particular washing machine of theirs that I would never had bought another washing machine from Maytag on 12/29/15 at all. I wish that Maytag would stand behind their product instead of selling this defective product to unknowing customers like me and countless others who thought they were buying a top notch washing machine from Maytag.

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

Purchased new Neptune stacks in 2002 and had several service calls on our expense and we noticed the hinges on the washer door were rusting! Ordered new ones from dealer but rust continues and has spread to top of machine over the bleach dispenser. The metal is falling off! Bad rust on the inside lip under door also. I contacted Maytag when I first noticed rust and they blew me off so I contacted the local dealer we bought from and they did nothing to help. Will never buy Maytag again and have not recommended it to anyone else either. ModelINGooZES. Serial: 51867064AJ.

We had our kitchen redone by Home Depot in Sept. 2006. It was gutted and all was replaced: walls, heat windows, doors, lights, appliances. The Maytag refrigerator stopped working 7 years later. I feel an expensive appliance should last longer than that.

We bought the Maytag Bravos XL washer 6 years ago when we moved into a new home. We have a large family and after reading many reviews, we settled on this washer. It has served us well for the past 6 years. At the moment, however, it is out of commission. The bearings wore out. My husband ordered new parts and we hope to have our washer up and running again in a couple of days.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

We purchased a Maytag dishwasher, Model #MDB7749, in the belief that it was a quality product. Many initial reviews were positive. Unfortunately, that decision was a mistake. The washer is only three years old and the control panel has failed. We are unable to select wash cycles. It defaults to Auto Clean/Heated Dry only. The washer has been lightly used.An online search found numerous complaints for control panel problems with this Maytag dishwasher. Please check ConsumerAffairs, Amazon, or Maytags own Facebook (Maytag was forced to create the Facebook page in 2010 under a mandate from the Consumer Product Safety Commission after a recall of dishwashers for fire hazards) before making any decision to buy a Maytag/Whirlpool appliance. It would also be wise to purchase an extended warranty.Our Whirlpool clothes washer failed after 5 years (bearings + controls). We cant afford to replace a major appliance every three to five years. The estimated cost to repair the dishwasher is $300 - $400. Maytag/Whirlpool customer service is indifferent to helping its customers. Its disappointing to see a made in America company produce such poor quality products and not support them.

On May 23rd 2009, I bought a Maytag Dishwasher and paid $360 for it. Within the first year, the circuit board had to be replaced, then one year later, the same thing. On October 8th 2011, it appears that the same thing needs to be done. I spoke with the customer service and they will not pay for it. Clearly, this dishwasher has a history of being unreliable and should be covered or replaced. The internet is full of complaints against Maytag for this very same model. How is it that they have not reacted or invoked a recall? I had a similar incident two years earlier with a Whirlpool dishwasher; it turns out that they are the same company. I will never buy their product again!

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.