I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

One month after warranty we had our first issue which cost us $380. Kinda my fault I was told by repair guy... My bra underwire came out during wash and destroyed the part we had to replace. Then a year later during spin cycle it sounds like an airplane taking off for about 10 minutes. Its so loud we cant even hear our TV! So guessing its bearings gone bad now? Which is a very difficult part to replace. And pricey. So guessing a new washer is in our future. We previously owned a Maytag washer and had it for 15 years and it still worked fine, we just wanted to upgrade. Big mistake! I wouldnt wish this washer on my enemies. I think the repair guys sets it to mess up when they do this reset thingy. Lol. Cause within a month of the renewed warranty we purchased was expired is when the 2nd issue began. I think the older washer are better because all this newer technology stuff is crap!! My advice do not buy Maytag Bravos series washer unless youve got lots of cash for repairs!!

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

I bought this washing machine 2 years ago or so. We have always bought Maytag. My mother still has hers she bought over 25 years ago and it still looks and works great. So my wife wanted a new washing machine so I said were going to get another Maytag. Boy did I screw up. What a piece of ** junk. Sounds like its grinding gears all the time, so loud. I close the door in the wash room and I can still hear my investment on a Maytag grinding my nerves because I spent so much on a product of a brand Maytag that I thought would be around for a while. Do not buy a Maytag.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

After only 2 years my microwave stopped working. Now I can purchase a new warranty which is just as much as a new microwave, have somebody come out and fix it, or pay a service charge which is just under $100 and does not include labor and parts. I figured out now why nobody calls the Maytag repairman. We cant afford it!

MDBH979SAM0 - Bought this dishwasher from Home Depot 2 years ago and have taken care of it, never abused it or anything. All of a sudden it just starts freaking out, once you start a cycle it will wash and then rewash and then keep going costing us money on electricity, water and wear and tear on the machine. Ive tried everything but it seems like its just stuck in start mode. The indicator lights on the panel flip out too, they will all blink randomly. So when I close the dishwasher and dont intend to start any cycles and it is off it will start up all on its own so Ive had to unplug it. Funny how I called to order a control panel part and its on back order... Very interesting how they are out of this part probably because everyones ordering it.

Bought a Maytag bottom door refrigerator/freezer about 3 years ago and within 6 months had the bottom drawer ice freeze issue that is so common all over the internet. Today is the THIRD ** time Ive had to take this piece of crap product apart and clear the ice. For all of you who have contacted Maytag in the past... Ill bet you got the same response I did when the fridge was new. They claim there are NO KNOWN ISSUES. They actually told me they had NO RECORD of previous complaints with this issue. MAYTAG SUCKS! I wouldnt take a free appliance from them. Worst customer service possible and they take no responsibility for their ** design and problems. There should be a class action suit for this issue. IF ANYONE IS EVEN CONSIDERING A MAYTAG APPLIANCE... Do yourself a favor and think twice.

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

The microwave does everything I need and want it to do perfectly. It has never needed to be repaired or replaced in five years. We bought it on sale from Best Buy and consider it one of the best bargains we have ever made. Easy to operate, easy to clean, sleek and, for an appliance, quite personable. I find it refreshing to say something nice about an inanimate object.

The washer buzzes. Period. I called Lowes...they said to unplug it then plug it back in so it will reset the computer. I did twice...Nothing. A light comes on for the sensor...Then nothing. I didnt see all the bad reviews for this machine. I had my other Maytag for 24 years and the tub was going bad. This scares me. I will be calling Lowes later. They are selling defective machines and they know it.

Updated on 10/09/2019: Well I wrote a review on my brand new Maytag washer that we bought at Lowes in June. When I wrote the last review I was waiting for our repair. They did come to repair and I was told by the repair guy (keep in mind the washer was only 2 months old at the time) that there were 3 fail codes. He said that it was overloaded or loaded wrong.That you cant wash towels with sheets, you cant wash any kind of rug no matter the size, which I only wash small bathroom rugs that are NOT oversized or heavy, you cant wash tennis shoes (which I have not). So I asked him what is the point of investing in what is supposed to be a top of the line, heavy duty, extra large tub, commercial washer? He said that you cant do that with any machine. I told him our old washer that we had 13 years had no problem with washing towels & sheets together. My point is that I am 100% disappointed in this washer & I encourage you to NOT buy Maytag, apparently they no longer live up to their brand.Original Review: We did our research & comparing & this machine came up on top. Its size suites our needs & we were excited about all the great features. We purchased it in mid July of 2019 so its 2 months old & for the last month it started to shut off in the middle of a wash cycle. At first we thought that maybe we were doing something wrong. So we would re-start it & it worked. Fast forward 3 weeks, it was doing it almost every time. Now it isnt working at all, it starts to fill up then shuts down before it starts to wash.Today is a Friday & I called Maytag to request a service call under the warranty (60 days old) Maytag had me on hold for 19 minutes before I could even talk to someone! The customer service person (once she was on) was very nice & sympathetic but couldnt get anyone out to service our machine until Tuesday, which is a HUGE inconvenience since we have not been able to wash for the last 3 days. I am highly disappointed in the machine for the simple reason that I paid for a new topnotch machine because my old one that 13 years old finally gave out & now am in the same situation & in for $1000 I paid for this new washer & having to go pay to do laundry 2 MONTHS later! I will add to my review once they have performed the service call to see if the issue is resolved or the machine replaced if they cant fix it.

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

I purchased a dishwasher and stove from Home Depot. Stove has already been replaced twice because of faulty manufacturing and now the dishwasher, after 1 1/2 years no longer works due to the control panel. I called a repair representative of Whirlpool/Maytag and explained the circumstances. Their own customer service people indicate that it is cheaper to replace a product then it is to repair it. Shame on Maytag and Whirlpool that they move their companies to countries outside of the United States and they no longer stand behind their product. Shame on them that what use to be the best product around is no longer worth paper you print on. I will no longer purchase any product from Maytag, Whirlpool or Home Depot since they all seem to line their pockets from products they know wont last. One mouth is worth a thousand complaints and I plan on screaming from the rooftops!

I built a new house in 2006. As part of a builders package, we had all new stainless steel Maytag appliances installed. The side by side refrigerator compressor stopped after 26 months (of course, passed any warranty). No customer support through Maytag and as previously posted very scripted responses. Maytag microwave handle has broken off several times, the glass seal in the oven door was compromised and the inside glass is stained - most recently the on-going issue with my Maytag dishwasher model mdb5601. Ive already replaced the handle /door latch assembly twice and am confronted with the current dilemma if I should replace the control panel that now appears not to be working. It goes without saying that I will never purchase Maytag products again. However, I am not in a position to replace what are fairly new products. That being said, I am reluctant to purchase costly replacement parts given their poor performance and ratings as mentioned in this thread.

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

Updated on 01/21/2019: I have contacted Maytag numerous times with no results. I purchased a washer and dryer on 2/7/2018 and the dryer takes hours to dry my clothes. I contacted them 2 months after my purchase and then waited and contacted again and again. I have contacted them numerous time with nobody contacting me back. I want a complete full refund in the amount of $1031.06! I want to purchase another washer and dryer from someone else and purchase both so they match.Original Review: Maytag MCT Dryer - The washer I purchase is great but the dryer doesnt dry worth anything. Dont buy it. Takes me hours to dry one load and the only reason I purchased this was because my old dryer was drying less but actually was better than this one. The time sensored dryer isnt worth 5 cents. So disappointed! I have had it 2 months, paid cash at Lowes and so unhappy!

Ive had my washer for about two years and have been disappointed from the get-go. I did a lot of research and found this to be top rated... Wrong! Even though I use the HE detergent and Ive even cut down the amount with no results, it leaves gobs of soap/lint residue on most of my darks and I wind up having to either rewash on clear or rinse by hand to get rid of the stuff.Ive also noticed some snagging on some brand new towels, but I attributed that to possibly the brand. Well, then I had an issue with some very expensive bottom sheets shredding and raveling and still didnt catch on. Today I noticed a different towel with similar problems, which led me here and walah! I see Im not the only one having these issues… Darn! Warranty is expired and Im stuck!

I dont know anything about the Maytag washers and dryers but have a Maytag washer and dryer. And I just recently bought a house that the owner is leaving both the washer/dryer, and both are Neptunes. I have an older set of Maytag washer/dryer and they are about 20 yrs old. They are both top load and I had one repair where a water line had a small leak and the service man came and fixed it and havent had any problems since. So I came on Maytags site to see how good these are, but from what I read, I think I will give the set of Neptunes away and just keep my old set as I am told them will last a good 35 or more years. They are heavy duty and large capacity. Thank you for letting me comment on your washers and dryers.

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.

Friends, Romans, Countrymen, At first I was skeptical and I once thought that I was the only one whose wife complained about the terrible soap stains and un-rinsed clothes. And finally my rinse and spin cycle stopped spinning and rinsing! However, after reading several reviews and complaints about the famous Bravo X He washer by Maytag and taking into consideration that there are over 650 complaints, making mine # 651. I now find I have lost all skeptical-ability and feel that we all may be comrades in this venture of purchasing the new trademark of the trade-mark Maytag. As almost all of us say our previous experience with Maytag was great. My parents had a Maytag since I was knee-high to a grasshopper and we were a family of eight. First we had the one with the rubber rollers, that was a work of mechanical genius. I even remember getting my arm caught in the rollers. Then my dad bought the spin dry model and that lasted a good 20 years. When I say the Bravo X at Sears it looked like the state of the art washer. However, and unfortunately I will have to agree with all of you. It is a piece of scrap metal and Maytag will not recall or recognize their mistake and make good on a recall or something. The least they should do is give us an old machine that does wash and spin to replace the new one that is less than 2 years old and does not work. I sure hope this letter does not fall on blind eyes. I think we may even have a collective lawsuit.Sincerely Yours;Mr. Lost All Skeptability!

Have used for several years, no problems. Not even with ice maker. The black color is good and matches other appliances. I like the pull out drawer for freezer items. However, the filter is very hard to change but other than that everything ok.

Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

I use a late model Maytag front loader. It does a great job cleaning and uses very little soap and water. To date I have NOT had to call the repairman to work on it. All in all I am VERY satisfied.

Purchased a refrigerator freezer in 2012. It freezes the refrigerator contents, ruins vegetables....freezer doesnt freeze the contents....stopped making ice. Clicks on and off every two seconds sometimes for twenty minutes......

Never waste your money and buy Maytag washer. Mine is XL large tub and has extra wash for extra clean. Dont waste your money. Never fills up with enough water. Almost everytime I wash I have to rewash the load because the clothes are still dirty, have soap spots and most of the time the clothes didnt even get wet. Horrible Horrible washer!!! My water bill has gone up a lot because I have to rewash the load so thats twice... I cant even use the XL tub because it wont fill up with water. Horrible product. Cant believe Maytag is still in business. They dont stand behind product. Called. Complained. They gave me nothing except for some free pods to clean a washer thats only 6 months old. Ive tried every cycle to see which one will wash the best. Still Horrible Horrible. Doesnt get anything cleaned. Here I thought nothing could get worse than a front loader? Well the Maytag is worse Horrible product. Dont buy. Dont waste your money. Try another brand!!!

My husband and I purchased our Bravo washer and dryer from Home Depot about 5 years ago. They have been the worst ever. Clothes always tear and we continue to receive an F1 error every time we try to wash something. I dont have the money to buy a new one, but I sure wish I did. I will never buy a Maytag anything ever!

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

We purchased a Maytag refrigerator, model #mf12269veb on 2/1/12 and for the past few months it has been leaking water out of the bottom freezer unto my floor and ice is forming inside the bottom of the freezer. I have read many complaints about this and if there is any recourse to this problem please let me know. So disappointed with this appliance.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

The Maytag washer is very quiet & economical by filling the amount of water needed per load so actually a money saver. Also got the huge drum to wash quilts & blankets. My old one lasted 10++ years. Hopefully get as many years out of the new one.

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

I purchased Maytag French door stainless fridge 5 years ago for $2200. The doors were out of alignment and I put in new control board; both items almost right away. Then in May 2011, we had to replace another control board for about $400. Then in July 2011, the compressor went out at a cost of $300 for the compressor, $350 for labor. I called to Maytag, Gwen agreed to pay for the compressor but not the labor to put it in. So we now have about $1400 invested in our $2200 refrigerator. Letters to Maytag CEO Mr. Fettig remain unanswered. Do not buy a Maytag appliance!

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

We purchased a gas range and over the range Maytag microwave a few years back and have had problem after problem with the microwave. Weve had 3-4, maybe more, repairman here and they replaced pretty much everything. Its been going for about a couple years now without a service call, but it went out again today. Very frustrating when you spend good money on junk. We are now to the point that we either replace it with another brand or we just put in a hood and have a microwave on the counter. Just so frustrating. I would not recommend Maytag over the range microwave to anyone!

Things that I have read that are true: Rips clothes/towels/sheets. No real problems with motherboard like some have stated. Bought Maytag Bravos Washer/Dryer in 2009. No real problems with the dryer, HOWEVER, may with the Washer. Had the pump go out in 2/2010 to the tune of $199.20 due to a small object in the pump. The repairman said it would just take a very inexpensive part from Maytag to prevent this. In 6/2012 washer not draining, clogged pump. All right, new to HE Washers, so told to use less detergent than detergent manufacturer recommends. $79.13 to fix clogged drain. Even though being careful with items in pockets, loose buttons, etc. AGAIN had pump go in 1/13, $214.22 (same problem cheaper in 2010, repair inflation). Wed noticed it was loud on the spin cycle (like a rocket going off) and were told at that visit the bearings would need to be replaced, and quoted approximately $280 to repair those. Havent fixed, waiting for something else to go wrong and then decide what to do with it. So in 4 years paying almost the purchase price of the unit (if I fixed bearings also). Crazy. If you bought a house and had to pay 4/5 of the house to repair it in that short of a time, no one would own a house!!!

Our washer stinks. We have done all the things suggested by Maytag, and it still stinks. Maytag suggested having it serviced by A&E, but I see on the Internet that they are probably not the best choice (very bad reviews). We called our local Maytag dealer, and they said that there is no fix available. They just stink. We will buy a new washer and will never buy anything Maytag again. I would suggest the same to everyone else.

Maytag french door bottom freezer model #MFF2558VEB5 - It stinks to read all the similar problems Ive had with my unit. Purchased Nov 2011. Problems started within a year. First minor, deli drawer broke. I use clear duck tape to operate it and that has been fine. But not acceptable. About a year ago the water leak out of bottom freezer was noticed. The bottom inside is frozen sheet. I break up and manually remove quite often. NOTE: I intentionally do not use, did not install, the ice maker - historically they are poor risk so I dont bother. The ice unit is in the machine but not installed. I assume my water build up which freezes on bottom related to poor design of defrost drain and that is supported by other comments here. I find it disgusting. Live and learn. Its B.S.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

Maytag XL Washer - My new machine is awful as well. Black clothes are smeared with I dont know what... looks like dirt. The wrinkle cycle doesnt work and the bedding cycle forget. Wish I read reviews... silly me.

I share the complaints of others about the Maytag Bravos washer (model MVWB300WQO), which I purchased in October of 2009.Besides being overpriced, its a washer that doesnt soak clothes, develops a bad odor, has silly things like unnecessary lights and music, and you cant add an item once the wash cycle has begun without the cycle starting over from the beginning. It also leaves washed items in twisted wads and the lid locks so you cant see whats going on inside. In addition, it damages items. Ill have to replace a full-sized blanket that it recently destroyed and now I cant trust that itll wash things safely, which is a problem. The person I spoke with at the companys customer service department simply said that I shouldve used the bulky item option instead of the regular cycle. I explained that Id used the bulky item cycle before and the same thing happened. The washer leaves larger items stretched very tightly across the tub and I suspect that is how my lightweight cotton blanket was destroyed. She offered to schedule someone to service the washer. But its not broken, its a poor design, so sending someone here would be a waste of time.

I purchased this dishwasher at least 12 years ago and it still works. However, after that much use some of the buttons no longer work. It has china, economy, regular, rinse only and extreme wash features.

I had two Maytag washers in my lifetime: one lasted 15 years and the other 20 years. Neither one had any service calls, just a sudden death. My newest Maytag is 1 year and 2 months old and Ive had two service calls so far due to the sensor unlocking the door. One time there were some socks caught “somewhere” and today the serviceman just reset the machine and it worked. He didnt know why it wouldnt work. It seems to me there needs to be some more detailed trials on these computer-operated machines. If I need another washer, it will most likely not be a Maytag.

Maytag Bravos washer MVWB750WQO frame assembly and cabinet rust - I sent letter of internal and external rust issues to Jeff Fettig (Whirlpool CEO) and received no response. Then, I sent letter a second time with an attached signed receipt. Then, I finally received a call from corporate staff member stating they would replace parts but not labor. Labor costs would cost between $350 - $500.00. This is without the initial service call and diagnosis cost between $100 - $125.00. The determined parts list cost would be $700 - 50% for Whirlpool internal cost + shipping be approximately $425.00. This is more than the cost of a new unit or the value of three-year depreciation value of the existing unit. This does not make any financial sense. Whirlpool should provide a new replacement unit at their costs. It has been three months and with no successful outcome. Also, via web research, there are many complaints about Maytag/Whirlpool and I am not the first in regards to rust issue. Therefore, Whirlpool is attempting to limit their financial exposure by only offering parts that they have to agree upon because the labor costs will not support this additional investment in a three-year unit. It makes more financial sense to purchase new or be offered a replacement unit.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

I bought my Maytag Dishwasher (mdbh979aww3) about two years ago and just last week, the control buttons on the right stopped working. I see on this site that someone else had the same problem and explained that the wires got corroded, so now Im not sure I even want to replace the part when it only worked for 2 years. Now Im stuck buying a new dishwasher.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

I purchased this new a year and 4 months ago and have had nothing but issues. We thought it cooked slow or cooked high/low but couldnt be sure if we were just imagining it until we had family come down at Christmas and complain about how slow the top burners are and why is it taking so long to boil water. Then again family for Easter where they cooked three days in a row and they complained that our top oven either burns or under-cooks the food which we had noticed but presumed we just mistimed a lot of food. Just recently the bottom oven wont heat past 350 and just constantly says preheating. The top oven followed suit shortly after. Nothing past 350.

I bought a Maytag Bravos washer in March 2015. Over the summer I had two items, both cotton t-shirts come out of the washer badly stretched and torn. Other items have come out badly stretched, but not destroyed. After the second shirt was destroyed, I called Maytag (Sept. 2015). A young man was sent over. He ran the diagnostic, finding nothing wrong. He did not check the agitator. He reported back that it must be the way I loaded the machine. I use the Normal and Active Wear settings, leaving the center clear. My loads are very small. Under these conditions items should not get caught. Maytag stands by their claim that it is my fault. I only figured out what was actually happening when I saw an item caught.

After 1 year and a month, the dishwasher would not work. When the Maytag repairman came, he told me that this was the 3rd one this month that had the same problem (the control panel). The cost to replace, it would be about $275. However, since I know of 3 that have broken, why would I replace it? I live alone and maybe have used the dishwasher once a week. There should be a recall on this machine. I called to see if there was a recall and was told Im sorry. I would advise anyone purchasing a dishwasher to avoid Maytag or any dishwasher made by them.

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

Washer Leaks, dryer noisy, cant balance washer, dry settings make little economical savings. Washer repair list, balance adjustment, filter body, door latch, door casket. Dryer lint basket felt repair. Door sensor, overall un-dependable.

I purchased this washer in January 2017 at our local Home Depot here in Mexico. It was a washer/dryer combo. Now, in July, a mere 6 months and only a few wash loads later, it has gone from the worst machine I have ever owned to what I consider to be garbage material. First of all, it boasts about not using much water. This is true... Only 1/4 of your load is in the 3 inches of water at the bottom of the machine and the top 3/4 never even gets wet. I couldnt believe it. Now, I put 2 sheets in this morning and it fills almost to the point of spilling out, though I have to give it credit for shutting off the water before it actually did so. This is a NEW washing machine!!! I, along with a lot of other folks from what I am now discovering, are all in the same boat. I remember Maytag being a mark of excellence way back in the day... This is no longer the case. Stay away from this company... I know I will.

I really like the refrigerator. Its easy to maneuver and frost-free, but I should have gotten the side by side. Also, make sure of your family size before you make final decision. Other than the size I would recommend to family and friends to purchase.

Products spoiling even if set at recommended temperature. Hard to clean bottom freezer. Not happy with this configuration. Had to have repairmen in because of stopped up drain which I could not access to clean myself. Does not close completely at times.

My 16-month old dishwasher, which is not being used everyday, broke its control panel. Maytag will not fix it for free because they only back it for one year. This is a major appliance, shouldnt it last more than 16 months? The cost to repair is almost as much as a new dishwasher.

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

After a year, the plastic parts of Maytag dishwasher is breaking and upstairs propeller is no longer running. Do not buy this product. I made that mistake.

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

So disappointed in Maytag - I have a 2013 Bravos washing machine that if I had it repaired again (less than a year after I had it repaired the first time and just over two years since we brought it home) the cost is going to two times the purchase price. And because it is just out of warranty Maytag is doing nothing about it, even though they know there is a flaw in their design.

3 months after we purchased our Maytag dishwasher in Jan 2014 (Sears) it broke. The service person told us that the ELECTRONIC CONTROL PANEL (START, CANCEL, WASH CYCLE SELECTIONS) was a common breakage issue and fixed it. It broke again around one year from our purchase date. Same issue, but kept working and not working. Finally we contacted Maytags customer service. Although courteous the only thing we were offered for this common Maytag issue was a $249.95 one year warranty for them to come and fix this recurring problem. I explained that we had already spent about $870 (including tax, delivery and installation) for our middle of the line dishwasher one and a half years ago and asked if they would consider either charging us for a smaller service call/repair or just do it because it seems to be a design and manufacturing issue. After one hour and no sympathy I had to pay the $249.95 to get a repair person out and be covered for one year from today. I dont trust the cheap quality and the lack of support for the product. THEY ARE OUT THERE TO SELL MORE INSURANCE AND CUSTOMER SERVICE DOESNT MATTER!

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

Washer does not clean very well, clothes are left with spots. The water level is never comparable to the clothes thats in the machine, it causes me to lose a lot of water as well as detergent. This machine is the worst washer we have owned. Its also very noisy.

I could care less if Maytag responds as I have already advised all my family and friends to avoid Maytag products. After spending over $1200 to buy this refrigerator it took 6 months for the ice maker to failed, and it needed a control board replaced. Maytag had a great reputation; however, in the past 5 years their products are worthless. I also have a Maytag dishwasher which failed and was stuck on cancel with a flashing light. The dishwasher panel needs to be replaced and I have just decided to replace both of these products with a different brand.

Maytag Washer was bought on May 2010 for $746.29 and it broke down. It was used only twice a week. It now requires repairs worth $991.36. All Maytag reps say is I am sorry, there is nothing we can do. Isnt there a lemon law for major appliances?

I own a MAYTAG BRAVOS XL* TOP-LOADING HIGH EFFICIENCY LOW-WATER WASHER. On 9/1/15, after reporting a problem, a service person arrived to assess the problem. His diagnosis led to a second visit on 9/8. On the second visit he replaced multiple parts, assuring us that the problem was fixed. When this proved to be false, we called for a third visit; this time a different person arrived. After disassembling the washer he found a large hole and another cracked area in the inner plastic portion of the tub. We made a fourth appointment for repairs, receiving assurances that it would be repaired at that time. I received an e-mail today (9/16/15) informing me that an additional 7 days would be required to arrange for delivery the required part. In the interim, my wife and I are forced to use a local coin operated laundry about every three days, totaling 7 visits at approximately $25 and 3 hours per visit before the next scheduled appointment. The compensation offered, 9 months extension of the existing warranty is woefully inadequate. I want the appliance replaced, as history has taught me that you are obviously unwilling or incapable of repairing it correctly in a timely manner. Additionally, I want the initial warranty that accompanies a new product extended to a full 3 years. We have paid out over $150 and wasted 18 to 21 hours of our time unnecessarily. I expect compensation for the funds spent as a direct result of the bungling, incompetence of your service staff. My questions are these: 1. Was the part defective prior to installation? 2. If so, why did the representative not notice it and refrain from installing a broken part? 3. Why was there no mention of the damage on the first visit? 4. If not, how did the damage occur? Did the service man damage it and fail to report it? 5. What caused the delay in obtaining the part? I have other questions, but will no longer spend any more time on this debacle. I cannot honestly say which is worse, their quality or their pathetic version of customer service.

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

I purchased a Maytag French Door Refrigerator in July 2011 from Lowes online and had it delivered on August 16, 2011. In September 2011, I could not get the ice maker to work. So I called Lowes and they called in a repairman. He came and replaced a part to fix the problem. I dont have any complaint with his work but here it is, October, and the ice maker makes maybe four ice cubes at a time on a good day.I am really disappointed with this product and according to their commercials, I would like to know which of these techs are setting around doing nothing, maybe he could come and fix my fridge once and for all. I would sure find it difficult to recommend any Maytag appliance as a result of this mess. I could call a repairman myself, but I was under the impression thats what a warranty was for. According to Lowes we are required to call them and they will schedule a repairman or the warranty isnt any good. I replaced a GE French Door with this Maytag, I sure am sorry I chose this Maytag.I know an ice maker problem is minor compared to some of the complaints on this appliance, but when you pay good money for a product you have every right to expect everything about it to work. Im just wondering where these appliances are actually made?

We bought a Maytag gas range in Feb of 2011. Shortly after that, we started having an intermittent problem with the oven not maintaining the temperature. It sometimes would not heat up to the proper temp or sometimes would get there but not maintain it. We have had several service calls all for this same problem. Each time they would replace things... nothing worked! We called Maytag and they said they wouldnt replace the unit until the same part had failed 3 times. Well, the service company came out 5-6 different times in the first year and replacing the main panel twice and the sensor and some other thingies I dont even remember. Pretty soon the warranty was running out, so I bought an extended warranty due to the fact that the unit had never been fixed. They sent out two different service companies who also were unable to fix the unit. It is now 18 months since we bought it, and Maytag refuses to do anything since it is out of warranty and the extended warranty company will only replace the unit up to 75% of its cost. So yes, we are very angry with Maytag and the way they wont stand behind their product and their total disregard for their customers.

Bought the pair of Maytags on sale at Lowes 6 years ago. They are commercial grade and wash everything. Have had no issues - works every time. It took a while to get used to not have an agitator but now it seems natural. Would buy again.

Maytag MVWB835DW was less than 2 years old (purchased 1-14-16) when it began to fail. Maytag sent repairman out, he declared it beyond repair. Machine locks, washes and adds more and more minutes and cant turn it off without unplugging 5-10+ times... sometime takes a week to get clothes out of machine because of locking itself. I have extended warranty and yet when I try to contact Maytag, to have them honor this, there is eternal wait on phone, online, no help whatsoever. I read via Consumer Affairs that there are almost 3,000 reviews on this specific machine being a problem yet amazingly the Maytag man never responds! I have spent many many hours with no resolution. Amazon says so many reviews have been written about this, that they are unable to take my review because of excessive reviewing.

Very disappointed with my 2014 purchase of model MDB8959SBS3 dishwasher. In fact it is no longer in service. We used the dishwasher approximately twice a day. The wheels on the pull out racks starting falling apart in the first 6 months. Then the soap dispenser failed. It would not shut. We replaced both the wheels and the dispenser only to find ourselves with the exact same problems in a matter of months. My hubby got really good at fixing both of these items. The final straw was earlier this year as when we turned it on the motor/water pump started making a screeching sound. Never had to replace an appliance that was only four years old in my lifetime. Just very disappointed with the quality of Maytags dishwasher.

I purchased a Maytag Dishwasher #MDB7749SBM1 as part of a complete kitchen remodel less than 3 years ago. Maytag was a great product years ago so I thought I would switch from GE to Maytag thinking that I had purchased a quality set that would give me years of great service! What a bad choice to say the least! This dishwasher has never dried the dishes completely with heated dry option. I never cared for the plastic latch and metal catch option either since I caught water dripping from the bottom since the door must not have been completely shut even though the latch was secure.Most recently, the start option on the flat control panel will not work. After opening and closing door multiple times I can get the start option to light up and run the cycle. Added bonus to start option not working correctly is that when the dishwasher door is shut, it automatically runs hours later with no human interaction. The dishwasher lights were lit up like a Christmas tree at 7 am this morning and running a cycle. Guess it thought the dishes werent clean enough. I am going to price out a board and determine whether I will throw this piece of crap in the dumpster and find a different brand! I HIGHLY RECOMMEND THAT YOU DONT BUY A MAYTAG DISHWASHER!

Love, love this washer. Does an amazing job cleaning colors, whites, and bulky bedding. If you like Tide Pods or other liquid pacs, this might not be the washer for you as they tend to end up inside the gasket. Powder-filled pacs are no problem however.

WORST MACHINE EVER! Besides the soap scum Maytag Bravos XL Washer leaves on all of our jeans and my husbands work pants, the machine decides when it wants to work and when it does not want to work. Weve had repairmen over, we have called the 800 numbers, just like all of the other reviews on here. Ive readjusted clothes in that thing more than Ive done laundry in my life!!! I HATE this machine. Ive memorized the manual from reading it so many times, have the correct detergents, tried washing large loads, small loads, lined up the clothes around the outside so the middle thingie is not covered, thrown clothes loosely in there. Every way possible. The machine senses, starts filling, then just stops. Today, no matter what I do with the load in there, it will NOT run, it keeps shutting itself down and I do not even know what else to do. NEVER EVER EVER buy this machine! We will never own another Maytag EVER.

My Maytag washing machine is nothing like the ones that my mom used to have. This thing is loud as it click, click clicks through cycles. Being a mechanical engineer, I assume that parts are taking a beating inside that machine to make all that noise. Then comes the wash time on this thing. With water level on auto sensing and one rinse, this machine takes over an hour to do a batch of wash. It literally stops dead for at least a full minute between each cycle then click, click, clicks its way to the next. It does not rinse very well as more often then not there is soap scum on the clothes when the washer finally stops. SPEND A FEW DOLLARS MORE AND BUY A DIFFERENT BRAND! Maytag is garbage!

We purchased a Maytag Refrigerator-Freezer from Home Depot, in July, 2014. The first two months we had this appliance, it would not make ice (we purchased one that had an ice maker it the freezer!). After numerous calls to Home Depot and about 7 service visits, the service company gave up trying to get the ice maker to work, and instructed Home Depot to give us a replacement refrigerator. The new one came with an ice maker that works some better, but still very slow in making ice, and the new refrig makes a grinding noise every time we open the door. The Maytag Company, whose service people never have anything to do, say this is a cosmetic problem, and they refuse to fix it.Have been in consultation with Whirlpool Company (who bought out Maytag I assume), trying to get the appliance repaired... or at least put an end to the grinding noise. We paid a lot of money for this refrigerator freezer, and have had nothing but trouble and issues with it. If you are thinking about buying a Maytag refrigerator -- Dont!!

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

Mine is the same sad story as all the others. Bought our Maytag dishwasher in 2013 (model MDB7749) and 15 months later, the control panel went out. We have contacted Maytag and they basically told us it could be our fault it doesnt work, so they wont fix it. Now we have learned that this is an issue that A LOT of people are having. We called their special number for this problem and were told they still wouldnt fix it since we called BEFORE having it repaired. So my question is, how is this legal and why arent they recalling this product? I know that there was a class action lawsuit against Maytag for this problem. Why dont we hold them accountable as well? This is bad business and we shouldnt allow them to take advantage of hard working people like this.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

Everything in my house is Maytag. I assumed they were the best. My dishwasher went out after three years, and I replaced it with a Maytag. Now, my over the range microwave is not working. I will not replace it with Maytag. I expect my washer and dryer to be next.

My machine is only 14 months old and will not even turn on. I opened the lid, and the tub was filled with water and the wet clothes sitting in there. There were only 6 items in there: 3 school skirts and 3 school pants, dripping wet. So I unplugged the unit to try and clear the circuit board - to no avail. The machine will still not turn on. The lights are on, the sensor turns on for about 3 seconds and shut off and everything just sits there. I did not get the extended warranty. My mom still has her Maytag she bought 30 years ago and its running like a champ. Wish I could say the same. I gave my sister my old Maytag - its 25 years old and its still running like a champ. This machine is a LEMON. I will never buy another Maytag again. I am so done with this brand. I hope that a Class Action suit is filed against them.

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

We purchased a Maytag dishwasher model number mdb7749sbm in April 2013. March of 2015 the controls stopped working completely. We looked online and instantly found it was a problem among many others, and said it was a result of corroded ribbon cable. We opened the panel and, sure enough, inside the ribbon cable the electrical wires were completely rusted through! We called Maytag, and, of course, despite the numerous complaints of the same problem, they would only fix it if we paid $250, or send us a replacement part for $350 to fix ourselves. Not going to spend that much on a dishwasher that already cost $600 and only lasted 22 months! We are attaching a picture that shows after we tried cleaning the rust (when Maytag refused to fix it) how much of the electrical wires disintegrated! We tried soldering a small wire to connect it again, but the ribbon was so thin it just melted right through.

I have had this washer for a few years now and it is the WORST machine ever. It never gets clothes fully clean as air gets trapped in some items so they stick out above the water. The drum only fills about 1/4 of the way no matter what you are washing. It is always unleveling and you have to constantly re-arrange bed sheets and larger items. I have to first soak larger items before the wash cycle. Nice HE machine. When I purchased this machine the sales person said you can wash 10 bath towels. I read the directions which said make small piles of clothes and I called and told her that after I had purchased the machine. Her reply was oh, I didnt know that. Obviously. This top loader without the agitator cleans great if you only throw in about 10 thong underwear at a time or two pair of jeans.

The washer gets mildew all the time no matter how much I use the tablets and yes keep door open. It still has so much. I scrub it and it keeps growing. Sometimes my clothes come out ripped also which is another frustration. Please help these two issues.

This is the worst washing machine I have ever had in my life. Machine started bouncing during the wash cycle and also the spin stopped. Never in my life have I had a machine fail on me like this one. I spent a lot of money on this. This machine should be recalled. I read up on all the complaints. Its a model #Tw6600TQ0.

The freezer will frost up and the shelves will not move. Repairman has been out three times, once to clean the drain. The second time he installed new tracks for 250.00. Two hours later they still wont move. The third time out he said it was repaired, but two hours later they didnt move again. We are very disappointed with Maytag.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

Hello, My recently purchased dishwasher has leaked water within less than half an hour of the fifth time to be used and showed error: F8E4, dishwasher model and SN are: Model: MDB4949SKZ. Serial # : FA3003347. Registered: 09/11/2021, Ive been calling Home Depot who in turn asked the installer to check the connection, and the latter advised and reported its a manufacturer issue. And calling Maytag for several times but no response or action. On-line service scheduling of Maytag is not working!!! And the live chat is not helping, as well. Now my dishwasher is not working since more than two weeks, knowing that it has been installed only a month ago.

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.

I always thought Maytag was the best, maybe because of their ad. Finally, I bought a refrigerator two months ago, which has turned into a nightmare. The company has sent a tech six times and they all say that it is a bad design which makes my vegetable drawer full of water because of moisture. And they refused to do anything about it every time (bad management). They have already spent more money on service than what I paid for the refrigerator. Figure that out.Do not buy Maytag. It was the biggest mistake I made. I also bought a washer and a dryer at the same time. I wish I could send them all back because of the ignorant people they have working for them in their complaint and service office. Anybody out there, if you want to buy an appliance, make sure it is not Maytag.