Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!

MMV5207BAQ purchased in Feb 2009. I paid $512.00. 5-09 Bob Millers Appliance replaced the door because it bubbled. 10-11 Bob Miller appliance replace the door because the handle broke off. 3-12 Bob Miller appliance replace the door because the handle broke off. 10-16 Door handle broke off again under normal wear and tear. 12/14/16 I went to Bob Millers Appliances and was told to contact Whirlpool. 12/16/16 I called Whirlpool, Tina said, yes it is excessive but it is not under warranty and they do not make the microwave any longer and they cant do anything to repair it and they can not fix the issue. I find it how to believe Im the only person who has had this issue. I dont have kids. Its only me that uses it.

Neither appliance (Neptune dryer and washer purchased in 2006) was worth the price paid. The dryer drum actually cracked and the washer repeatedly gets hung up on 3E. I called about the dryer and got an Oh, well response. “We dont know whats happened to that dryer.” What happened to both appliances is that they were used for their intended purpose. I do laundry for my husband and me. Is that too much for a Maytag? Customer service is equal to indifference. So much for Neptune. And thanks for standing behind your products. What is the life expectancy of a dryer drum anyway?

Bought the washer last week. Balanced it per installation instructions. Washed several loads. The darn thing goes off balance almost routinely. Have rechecked the level on several occasions and found it LEVEL. Contacted Maytag. The lady I spoke with said to just use it and it will level itself out. So much for Maytag help! This will be the LAST Maytag product I buy.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

Ive had this Maytag microwave for about 4 years and the magnetron had to be replaced. The keypad was replaced three times due to SE code shutting down unit which happened again. When I explained this to Maytag, they said it is out of warranty. I explained to them that the last keypad which was replaced was only 6 months old. They replied but the unit is out of warranty! I would never recommend Maytag or any affiliated companies to anyone.

Water ran out of washer and flooded my garage. 1) Replace computer. 2) Wrong computer. 3) Water still flooding garage. 4) May need water valve. 5) Showed up didnt know what to do, then left. 6) Whole new tub - 3 hour repair - 2 weeks until they have time to repair. Still waiting. HELP.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

This is a review of a washer that is no longer sold. I bought a top of the line Maytag washer 45 years ago. After around 25 years the control (all mechanical) started sticking during the cycle. I opened it up, sprayed it with TV Tuner cleaner, worked it a few times, and it has worked perfectly ever since. That is the only problem or repair on that machine since it was purchased!

I purchased this Atlantis dryer several years ago. To this day, I have replaced the rollers and drum three times. What a piece of junk! This will be the last Maytag I ever own.

Maytag Centennial - It came with the house. I think its a line made special for rent-to-own kind of places. I cannot stand the washer. It will not take fabric softener unless its in the ball and if you use extra rinse you dont get to use fab softener at all. (I like liquid fab softener on some things). Why it doesnt have a dispenser is beyond me. And the bleach dispenser is poorly designed, too close to the tub and splashes every time. Ive had this six months and would get rid of it in a heartbeat if I could afford to. Plus it snags towels. The washer is crap. And its a Maytag. I wish it would break so I could justify buying one that has some decent features like fab soft dispenser, bleach dispenser that doesnt splash, drum that doesnt snag.

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

I bought a new Maytag refrigerator on July 2, 2011. The ice continues to drop after removing your glass. Now you must pick the ice from the floor. Maytag said it has a 10 second delay and will continue to drop ice. Im tired of picking up ice and wiping water from the floor. Who wants a product that leaves a mess?

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

We have a Maytag washer. It is the noisiest washer I have ever seen! It is in the garage as you could not have this washer in a house. The deep water wash is not deep enough. It bangs and knocks VERY loud! There have been times when all of the clothes are not even wet.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

I recently purchased a Maytag washer and dryer from Lowes. The performance of the washer was highly unsatisfactory. The water sensor does not allow sufficient water to enter the machine. Thinking it was a malfunctioning machine, I spoke to Lowes, and ask them to swap it out with another machine. They were cooperative and pleasant to deal with however, the replacement machine was no improvement. The water sensor does not allow enough water to enter the machine to even begin to saturate the load of laundry! I bought a washing machine, not a dry cleaning machine, but a dry machine was what I got and that is NOT okay with me. The literature states that load will not be covered with water, so that is how it is designed to work. With inferior water levels, and no agitator, there is not even a chance of water splash saturating and cleaning clothes. I am not an engineer, but common sense says this is efficient nonsense. VERY, VERY DISSATISFIED!

I bought this electric dryer Bravos (Model# MEDB850YW0) in Nov. 2011. Since I bought it, its giving me the same problem - it doesnt want to turn on. Today is the 6th time that I have been calling the customer service to fix it. Yesterday, it just got fixed; and today, its not working again for the same problem. I asked them if they can give me a new one, since its not even over 1 year. But they said they will not replace it because it cant be fixed. But it is so ridiculous, and its wasting my time. This is so unfair. I paid $800.00 for this machine.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

Like many others Ive read about online, our Maytag fridge model MFI2269VEW5 with bottom mount freezer has ice forming at the bottom of the freezer compartment. The ice then melts and runs onto the kitchen floor. At this point, I am able to prevent this leakage problem by removing the 1/2-inch layer of ice that builds up about once a week. Using a stiff plastic spatula, I am sometimes able to remove the ice in one large sheet but usually it breaks up and has to be removed in pieces. I have seen several videos online showing how this problem can be fixed but as a pensioner with limited income, I am sure the expense of a repairman would be prohibitive. I could likely make the suggested repairs myself but because of a knee replacement, I am not able to kneel for any length of time so that is out of the question. Besides, when we purchased this fridge 3 years ago, we expected it to run trouble free for the rest of our days. This is obviously a design problem and Maytag should be covering the cost for all repairs. However, it is a sad reality that Maytag and their owner, the Whirlpool Corporation is only interested in making a profit to satisfy their stock holders. They apparently only pay lip service to making quality products that last and customer satisfaction seems to be a thing of the past.

I have a dishwasher that would randomly leave chunks of food on dishes, above and beyond not working and would take entirely too long to clean the dishes. This silly thing would run for hours but still produce dishes that were clumped with food. The local Maytag could have cared less. They said that it was the wrong detergent or hard water or we have not pre-cleaned enough. I am taking the old dishwasher to the range for proper disposal as a backstop, and buying something not made by imbeciles.

Bravos WL purchased in May 2015. Terrible product. Last week stained 2 shirts beyond repair. Maytag service repairmen stated these machines were poor quality and the only settings that somewhat work are Deep Wash and Bedding. They recommended I buy something other than Maytag. I am not making this up - it was unbelievable. I got Maytag on the phone while the service techs were here so they could hear the comments. The supervisor, Kimberly, said I could not get resolution unless the technician declared it a functional failure. I asked for the definition, as I would assume the basic function of a washing machine is to clean clothes. Still working the steps to resolution, but I believe there is evidence for a class action lawsuit.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

Softener container is clogging up with softener. Worse, the drain in the fridge has frozen up twice and now again I am having to pay someone to clean it out. A pool of water accumulates in front of the fridge where the ice melts. Disgusting in new appliances.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

Faulty Maytag Bravos electronic dryer model MEDB400VQ0 - I purchased a new Maytag Bravos washer and dryer in Feb 2011. About 3 weeks ago, I noticed the dryer not drying my clothes. They were hot, but not dry, leaving them hot and steamy. There was also wet lint that kept accumulating inside of the dryer. I took the back off of the dryer to see if there was an obvious problem and I found the blower belt and large bolt that holds one end of the belt to be off and laying on the bottom of the dryer. I have also looked online and did a search on this make and model and the issue I was having, it brought numerous people having the same problem on multiple internet forum sites. Apparently, there is also a service bulletin on this exact issue, but according to the Maytag customer service department, no recall. Therefore, I am out of luck as far as getting any kind of repair (unless I pay for it) because I am out of warranty by 3 weeks. I purchased the Maytag brand thinking this was going to be the best and will last me a very long time. Unfortunately, I was wrong. It only lasted me one year without breaking down and the customer service department is horrible. You can tell they definitely dont stand by their name, the Maytag name is a thing of the past. I will never recommend this brand to anyone else for purchase and I regret having swayed my mother to purchase the very same set I did. This has been an awful experience and I am wishing I had chosen a different brand. Maytag leaves me angry and very much dissatisfied.

On June 17, 2013, we purchased this over the stove microwave for my elderly parents. They use it daily to heat their lunches. In December 2014, it would stop turning and finally in January 2015 it completely died... no heating and no turning. The technician quoted a repair at $200 when we only paid a little more to purchase it. I emailed Maytag to tell them that it was manufactured and purchased in 2013 with light use and that it should never have died in such a short period of time. An e-Solutions Specialist contacted me to tell me that they certainly understand my frustration, but that occasionally failures occur and that there was nothing they could do. I replied back that they could DO something because they were customer service and that was there job. No reply back yet, but after seeing so many of the same issues here, Im not holding my breath and I would never buy or recommend a Maytag product of any kind to anyone. I dont expect 15 years from an appliance, but I certainly think 18 months is just wrong.

Bravos XL Like so many others Ive read, this is a terrible product. Washer constantly goes off on unbalanced load. After 14 months, the plastic tub disintegrated. Maytag tried to sell me the service and extend a warranty for $300 also. Just like all the other reviews. Wow, has Maytag gone downhill.

I purchased a Maytag Centennial washer and dryer on February 4th. It was delivered on the 11th. I am dissatisfied with the performance of the washer. I use the same amount of detergent and fabric softener as I did for my 15-year old Maytag washer, but the wash is not as soft as with the old machine. Also, the wash when finished appears to be a lot wetter. What is wrong? What else can I do?

I purchased this washer in 2010. It has broken 4 times since purchase for the same reason. I was told by the appliance repairperson (which Maytag referred me to last time it broke on 03-11-11) that the manufacturer does not replace the machine until after it has broken down a 4th time. Now, the warranty has expired (in 09-11), and it has broken down again for the same problem - water wont fill. Sherry at call center informed me my machine does not qualify for replacement. Then, she would not give me a number or contact info for corporate office so I could forward my complaint. This machine is only slightly over a year old. I have had nothing but problems with it. I want a new machine, or at least unlimited repairs for the recurring problem. And I should not have to pay for a warranty that costs almost as much as the machine itself when Ive already paid for the machine, and at least an equal amount to the cost of the washer in repair bills just to keep this lemon on the road. I want a number and a name for someone that will listen. I may be part of the shrinking middle class, but I am a customer, and I should be treated right. Please help me.

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

I bought this washer brand new in 2011 for $650. I had bought a Maytag washer before in 1967 and it was still running in 1995 when I gave it away. Considering my first Maytag lasted me nearly 30 years (Last I heard the machine was still running in 2005), I never thought my new Maytag would give me any problems, until it was at least 10 years old. (I did know Maytag had been bought by Whirlpool but didnt expect any difference in quality). Boy, was I wrong! After using it for a month the machine broke down and it had to have the clutch and gear box replaced. Last week July 2016 the machine broke down again. It was the internal computer (referred to as the electric control unit) a printed circuit board that retails for approximately $300 (A ridiculous price given that much more complicated laptop and tablet computers today can be brought for $100, the circuit board should retail for no more than $40).With labor the repair bill came to $550, which was nearly as much as a new machine and did not justify the cost. Supposedly the electric control is susceptible to current surges and power outages. Given that this is the case, it makes no sense whatsoever that a machine billed as eco-friendly would carry a part that will doom it to the junk pile because of a power surge or outage and does not carry a surge protector. After learning of my experience Maytag called me the next day and offered to sell me a new Maytag at a discount price, which of course I flat-out refused.I would never ever again own a Maytag appliance or one made by its new owner (as of 2005) Whirlpool. With such susceptible electric units these appliances will sooner or later result in electric fires that will end the life of its owners. The US govt needs to protect US citizens from these predatory companies that make over-prized, throwaway products labeled as eco-friendly that are potentially dangerous. My advice for anyone that is thinking of buying a Whirlpool or Maytag washer dont do it. For those that already own these machines do not run them without a heavy duty surge protectors. It is not worth your life.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

I like the full width drawer for large items. Our Maytag refrigerator is 12 years old and just beginning to make noises and get too cold. The little plastic features for setting the temp and humidity on the produce doors were the first to break. Water is inside door which is not as convenient.

This washing machine has been very reliable.No repairs needed yet. This machine has stood the test of time. We use it at least.. four times a week. Light and heavy loads. It fits in our washroom and budget. Just perfect. I would recommend this brand to everyone.

My washing machine is 2 1/2 years old. It is not overused, just 2 people in the household. Maytag wanted to sell me a contract for $320, I declined. After research I see that this machine has many complaints against it. I bought Maytag because they never need repair. I would like Maytag to fix this machine without charge or recall the machine. From what I have read, these machines are defective. The electronics are failing at 2 to 3 years.

Purchased my Maytag range/oven 14 years ago and it still works to this day. I had to replace both oven heating elements. I am a do it yourselfer, took me less than 5min to replace both. The cook top is easy to clean. As long as you take care of it, it should last you a long time.

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

These are the issues, Water level is ridiculous, clothes often have dry spots, I use only the high water level which is a joke. The tub bottom is very hard to reach because it is too deep even for a man with a long reach. The tub itself is about 16” deep but never fills more than 4” of water on the high water setting. Why such a deep wide tub when you can only put 4” of water? Cleaning is poor, the machine is very noisy, very. The worst machines we have ever purchased with ridiculous sensors, bells and whistles. The dryer takes forever to dry clothes and again the sensors are a joke. The high efficiency of the units means you work much longer for clothes that are wrinkled, spotted, less clean looking and sometimes damaged. Where is the savings? And don’t say hydro and water as the washer cleaner cost, wipes that out and more. We gave our 26 year old machines to Habitat, neither machine was ever serviced and were in perfect condition, they were Maytag. They have destroyed their name. So sorry we decided to modernize our laundry room.

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

We purchased a Maytag from Lowes about 3 years ago. The spin function quit working properly last Feb 19. We paid $350 to have parts replaced thinking it was a fluke and we would be set for a long time to come. Well, last week the same thing happened... not even a year later. Lowes doesnt care and Maytag doesnt care. They want you to spend more to get a warranty to get you to 5 years... well as far as I am concerned that is not good enough. An appliance should last 10-15 years. This Maytag was to replace a Whirlpool that caught all of our clothes in the agitator fins, so after a short period of dealing with that we paid out for a Maytag without an agitator. So in the span of 6 years... we had about $1,500 of dissatisfaction. I believe our repair guy said they the companies are one and the same. Selling junk ought to be illegal.

Our Maytag refrigerator is leaking water all over my kitchen floor to the point that my floor tile has lifted. The ref. is a French door with water and ice in the door and freezer on the bottom. We have been cleaning up puddles of water at least several times a day. I see that this is not an isolated problem, as others have complained about this defect doing the same thing with their Maytag refs. Why hasnt ConsumerAffairs demanded a recall on these expensive defective refrigerators to date? I am truly disgusted.

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

Maytag washer was bought May 2010 with an extended warranty, which expired May 2014. This machine was used by two people with average wash loads. Five months later the machine computer programming didnt work and the machine sounded like a jet taking off. Whirlpool said a one-year warranty would cost $329! This would have been less expensive than a new machine, but I felt I couldnt trust having it repaired. A repairman very familiar with Maytag products said he had three service calls the same day with similar complaints for the Bravos 300 series. He told me the bearings were bad and the cost to fix was not worth the money and this machine should have been recalled. I bought another brand and will not buy Maytag again. When my new machine was delivered, there was grease on the floor from the Maytag.

We bought a Bravos washer 13 months ago and its been problem after problem. We had 6 service calls and the problems continue. From bearings being replaced to sensors to error codes, and now the washer drips water. This is the worst washer I ever owned.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

I purchased this Maytag Dishwasher Model MDB8949SBM on November 23, 2013 and installed dishwasher in late January after new cabinets/countertops were installed. After four months the control board failed. I live out in the country and Maytag does not pay for a repairman to make a special trip for repairs, so we had to wait 2 weeks when the repairman was in the area. We purchased this dishwasher on reviews which seemed pretty good, but never bothered to check on complaints of Maytag dishwashers. I can see most all complaints are the control panels failing. Well it is November 19th and the control panel has failed again. My wife said the lights blink and when she presses a wash cycle, a different wash cycle will light and blink. She will press the start button and nothing happens. You can bet I will call first thing in the morning as the warranty will expire in a few days and I will write the persons name down and the time that I talked being that Maytag seems to lose conversations with customers. I hope Maytag doesnt give me the runaround like may others on this site. I dont understand why Maytag doesnt correct this problem that they have known about for years.

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

My husband purchased the Bravos XL washing machine less than a year ago at Bensons Maytag in Peoria, Illinois. Within months of purchase we noticed our clothing coming out with stains they didnt have prior to washing. After hundreds of $$s of clothing ruined we realized it was due to the fabric softener dispenser. We cleaned the machine multiple times & ceased using fabric softener. No luck.Today I finally had enough & called Bensons service department. The fellow I spoke with told me, You are not supposed to use fabric softener with the Bravos XL. I asked why a $1000 washing machine would have a dispenser you were supposed to use. He told me it was because people like to use it BUT you werent supposed to use it. I asked, Why would there be a dispenser if you werent supposed to use it. He told me the salesperson should have explained it during the transaction or I should have read the owners manual more thoroughly. I asked how I needed to go about correcting the problem & he told me to clean out the machine with really, really hot water. I explained we had multiple times.He didnt have any other suggestions so I asked about setting up a service call & requested he access my information so we could verify the warranty. He confirmed the unit was under warranty. I asked to schedule service & was told there would be a $50 service call fee. I told him, I would figure that would be under warranty to which he explained it would only be under warranty if it was the machine ruining my clothes. I asked, What other reason would there be for my ruined clothes and he told me if the laundry was being ruined because I used fabric softener it would not be under warranty. So I repeated that saying So you are telling me if the machine is ruining my clothing because I used fabric softener it will not be under warranty? and he got flustered and basically said he didnt exactly say that and they couldnt confirm anything until a tech took a look at the machine. I told him I would have to speak to my husband.So this is my question... why on Earth do we have a company building $1000 washing machines WITH A FABRIC SOFTENER DISPENSER if you are not supposed to use it? I have never, ever, EVER had a washing machine do such a lousy job. I have never, ever, EVER been afraid to put clothing in a washing machine... not even in a cheap, crappy laundromat. Shame on you, Maytag!

I purchased my 10kg commercial Maytag dryer in March 2015 and started using it in May 2015. Within two months the heater had broken. I contacted the people I bought it off and it turned out I had to contact Whirlpool. It took them 8 weeks to get my dryer going again. The dryer broke down again in November. This time it was a sensor. Again I had to contact Whirlpool, it took them three weeks to get it going again. Being a care home the dryer is essential to our business. We were led to believe when we took out the extended warranty that the dryer would be fixed within a week. I will never purchase a Maytag again or anything to do with Whirlpool.

I bought a new Maytag French door refrigerator a few years ago and have been disappointed ever since. The quality is second rate and now the ice maker has failed. The product looks good but performs poorly. Buy a more quality foreign made product instead. Before this I had an LG which was quieter and never had a problem after 10 years.

Within the first 2 years, the dryer stopped heating. After a $300, a few parts and a few attempts to repair the dryer worked again. The sensor still kept saying check the vent and we gave up and removed the outside vent cover. Works great now. The washer worked great until year 4 when it began to sound like a helicopter. It got so bad that it literally hurt my ears and could be heard outside. It also leaked. Called repairman and they couldnt even remove the drum because it had rusted solid. After a total of 4 years we are replacing the set. Do not WASTE your money!

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

We purchased a Maytag 4000 series washer and dryer in October 2011, and within 5 months, the main bearing failed. The Maytag repair person told us it was an inherent issue and to make sure we use HE detergent (We always have.). Maytag advised parts were not available for 3 weeks, so no washer after 5 months of use. The bearing failed a second time after 11 months. Maytag refused to replace the washer and advised it was repairable condition. Now, we have the bearing fail a third time, and Maytag has advised that they would not repair the washer under the extended warranty program. They offered us 75% refund on the washer (So I guess they expect their products to only last 4 years.), which is simply unacceptable. We are now faced with purchasing a new washer, which will not match the dryer; or we have to purchase a washer and dryer of another brand. Maytag has provided pathetic customer support, and their response or lack thereof shows that they simply just dont care about their brand image or the customer.

I ordered my dream refrigerator (Maytag Model MFT2776FEZ) on 05-12-2017. I had to wait 4 weeks for it to arrive because it was on back-order. I was willing to wait. All was good for 6 months. January 2018, the six month old refrigerator quit cooling. It took 2 1/2 from the service call until the part came in to fix before I could use my refrigerator again. I lost all my food. The same thing happened again in March 2018 except that it took 4 weeks for the part to come in once the serviceman ordered it. I lost all my food for a second time. February 2019, the same thing happened again. I placed the service call on 01-31-2019 for service, but the tech could not come out until 2/6/19. The part had to be ordered and could not be installed until 2-28-2019. For the 3rd time, Ive lost my food. My best friend that has appliances that are nearly 30 years old. She was going to replace all of hers and get exactly what I ordered. She has changed her mind and has decided she would rather keep her outdated appliances because they work.

I have had a number of Maytag washing machines in my life and have never disliked a machine as much as the last one I purchased! The bleach dispenser is awful and any bleach that happens to land on the outer rim has ruined many clothes. I took them to my dealer to show him the ruined clothes and was told bleach does not evaporate do must be wiped off each time. With no soap dispenser I find I have to put the soap in first and keep trying to fill the machine some before I add the clothes. This takes forever but if dont do this my clothes are stained. I purchased this machine on April 11, 2017 and can not afford to go buy another washer at this time. The Dealer can not help me and when I called Maytag they were not interested! Buyer beware!

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

Maytag Model #MBR2258XES refrigerator purchased May 2014 from Home Depot. Problem #1: Freezing in refrigerator compartment (frozen vegetables). Problem #2: Water leakage on floor from defrost. Wood floor is/has expanded and may now be ruined. This model is now discontinued. Looking into contacting an attorney.

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

Washer purchased in May 2013 last month it stopped completing the drain and spin cycle and cloth stayed wet. To have the machine repaired, we would have to replace the control panel. The cost of replacing the control panel plus the service call was 76% of the cost of buying a brand new machine. As such we are disposing of the machine and will be purchasing a competitive product.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

The washer does not wash properly at all. There is not enough water. The clothes come out covered in lint and still soiled. MOD: MVWX655DWI, SER: C63142093. DO NOT PURCHASE THIS PRODUCT unless you want a ton of frustration!

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

I bought a Maytag microwave model mmv4203ds00 on May 2010. On 8-20-10, the microwave stopped working. It was serviced under warranty. However, on 10-31-11, the microwave stopped working again.

Bought a Maytag MVWX655DW top loader clothes washer from Best Buy on 7-7-2020 it was delivered as promised on Friday 7-10-2020. The people who delivered it were very professional and nice. They did a great job installing it. My wife went to use it for the first time Saturday morning 7-11-2020. Luckily this washer had a see through door. We could not believe our eyes, it never put enough water in the tub to cover the clothes. So as we watched the clothes on top never participated in the wash, they just moved around. When it went to spin cycle it was making a loud clicking sound as it was shaking. So we tried different settings, after 3 loads I called BB and said I want to return it. This machine has been mislabeled, its not a clothes washer, its a noise maker at best. DO NOT BUY THIS MACHINE. IT DOESNT WASH CLOTHES.

My dishwasher just stopped working 1 year after purchase. Apparently a control panel issue. I have sold Maytag appliances for over 10 years and this is the thanks I get Maytag... Unreal. I wont buy a Maytag, Amana, Whirlpool, Jenn-Air, KitchenAid, etc.

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

Maytag bravos xl - HORRIBLE at washing and cleaning the clothes. Broke a little after a year... Went to Maytag site, saw that they push 10 yr warranty. Transmission went out... but not covered?? Garbage.

This washer is garbage. Control panel went out twice in less than a year

Does not clean properly! Water level is too low for clothes to move around properly. This appears to be a very poorly engineered product. We have had Maytag products for many years. The only good thing I can say about this product is that it beats a scrub board. Would not recommend Maytag product to anyone. Looking at other complaints it appears that Maytag is doing nothing about this. Will try to sell this at a yard sale and hope no one asks my opinion. Then go buy something that works.

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

Have had problems with the set since day one. Bought brand new from Home Depot. Got a great deal and now know why. Never cleaned the clothes properly, water marks on so many items, musty smelling regardless of how many times we cleaned it, horrible at removing stains, and finally not even 5 yo the motor stopped worked. The dryer has been repaired too and hasnt ever done a stellar job. Will never buy another Maytag product again!

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

The functionality of this machine is so awful. I had the dealer replace it only to find that the awful noises that the machine makes, the fact that the clothes don’t get covered by the water and the clothes are so knotted after the spin cycle you have to untie them is normal for this awful appliance. In the sensing stage the machine groans like a laboring motor around 30 times, then stops with a jolt. My machine is next to the bedrooms and the noise wakes people up. Even in the “deep water” setting, the clothes are not covered by the water. The wash cycle is short and noisy and the spin cycle goes on forever. In the end I have to untie the legs of pants. Whoever designed this machine should be ashamed of herself or himself. Shame on Maytag.

I would like others to know that Maytag does not stand behind this product at all. I am not sure about other products, but after talking to Maytags customer service team I would guess you would get the same runaround with other products. We have had our washers for about eight years now and have had many things go wrong with it. The one that gets me the most is the one that my appliance repair service does not cover and that is the main bearing. I have done some research to why this is and most of them do not cover this, because they should last for the life of the washer. Most washers last for more than ten years. However this washer has only lasted a few years on each bearing. I have now put in my third bearing into this washer. The last bearing only lasted two years. If I had to pay for labor on replacing this part I would have not replaced it. I had been given a quote for replacing it and it was over $350. Some places wanted more than $400 to do it. To me the washer is not worth this. Yes we paid like $900 for the washer, but it is not worth putting that much money into this washer. If you cannot replace this part on your own then just walk away from it. Buy a Speed Queen. I know Maytag has sent parts to other people free of charge, but I have not been so lucky. When you send others part to fix the same problem, to me that is admitting that there is a flaw in this washer. With that said my wife and I already filed a BBB complaint against Maytag and will be sending a letter to the Minnesota Attorney General. I have proof they have sent replacement parts to others and dont see why they cannot do the same for me. Maytag is own by Whirlpool, you think it would be cheaper and easier to make customers happy than just brushing them off. I would say that customer service in many of these large companies and even small companies is gone. I remember when you would call a company and make a complaint and they would go out of their way to try to make you happy. Now they come up with reasons why it is all the customers fault that their products are bad. Maytag is just another example of a greedy business that does not care about their customers. So please do your research before you buy this product and good luck to those who have that are stuck with the junk that Maytag sells customers.

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

I bought the dryer (Maytag Gas Bravo Dryer) from Home depot in December of 2010. The thermostat went out in July of 2011 and has replaced the same part 5 times up until August of 2011. Then they put a new burner with a thermostat and it lasted till June 1 of 2012. Now the warranty is out, they want me to repair this piece of **. I will never buy a Maytag product again.

Ice maker stopped making ice within first month. Repair man came out next day. Said ice maker only makes 7 cubes at a time 8 times a day. REALLY? A $2000 refrigerator only makes 50 ice cubes a day??? Why would I need a refrigerator that size if there was only one of me? Obviously, Ill be keeping a bag of ice nearby.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

I have a MGDB850WR0 Maytag Dryer. I have had to replace the thermo sensor/heat sensor three times in the past three years. Dryer takes forever to dry. I spoke to the repairman who told me in confidence that his company receives a lot of calls about this specific dryer for the same reason. He said the part was originally made faulty and thats why it keeps going out. The part being the thermo sensor/heat sensor.