The washer stopped and displayed F51. It had that growling, horrible sound like it was dying. After restarting and trying everything, including going back to Lowes to see if a serviceman could fix it, with no luck, and father reading all the reviews on the F51 error and all of the displeased customers we divided after two years on a $900.00 machine, we would tear it apart and fix it ourselves! If possible and if not, what are we losing? Nothing! What we found was clothing between the outer casing and the drum preventing it from spinning. Unfortunately, we did not know how to get to them. With a lot of effort, we got the leggings out that was causing the drum not to spin. I am sure there is a lot more socks and a pair of fairy wings that I never found after Halloween in there. If there is anyone out there who knows how to get the outer casing off of the drum, please let me know. After removing the tights, I no longer have the error code F51 and my washer now works. I just wanted everyone with F51 error code to know it goes away after removing the clothing that gets stuck between the drum and the outer plastic casing around the drum.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

I also bought a Maytag Neptune MAH5500BWW and matching dryer model #MDG5500AWW in 2001 and within a month, I called Sears and Maytag. I told them about the terrible odor and mold growing. The repairman said it is normal and told me to use Tide detergent once every two weeks. The dryer had a major breakdown and I had to buy a whole header with all the electrical components. I too bought the brand name Maytag due to a good reputation that Maytag had. I never received a recall notice or anything from Maytag. I will never buy Maytag products again. I found out from a salesperson at Sears that Maytag was sold to Whirlpool. The salesperson said the reviews are terrible for Maytag products especially for my models. I will never buy from Sears, etc. What can you do for me? Maytag and Whirlpool need to take their responsibility for their products! I am truly lucky I did not buy a plane from them. I and a lot of people would be dead.

Purchased the Maytag Bravos washer and dryer at Home Depot. Previously had a Maytag set that was 25 plus years old that still ran well but was rusting out due flooding. Figured Maytag had great products. Have had mine for 4 years now and had nothing but trouble. Paid countless service calls, mainly on washer, will work for a short while and then stop again. Cant put more than 4 towels, or 3 pairs of pants or basically anything or the codes start popping up. I am so angry that a product I paid a lot of money for is such a piece of crap. Maytag Company has been no help and I see with all the complaints on this site I am not the only one who feels this way. A class action suit would be great!

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

This Maytag Centennial is the WORST piece of junk I ever purchased and I received the same uninterested response from Maytag as everyone else. Maytag sent a service man out who said it was functioning as it was intended. Once started, this washing machine cant stop if you forget to add an item. It dumps out all the water and starts the hour-long cycle over. All settings are an hour-long cycle. Unless Bulky or Delicate is selected you only get 2 inches of water -- Even for Heavy Duty. No matter what the setting, the clothes do not come out clean. You must hand wash them first. Maytags are no longer a desired product.

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

No problem with retailer. Problem is this top of the line Maytag dishwasher, Model# MD8895lAWW. Stinks all around. Takes long to wash and load, times are far apart and too few so holds few dishes. Dishes and glasses break because of the tine spaces. Horrible dishwasher for high price. I hate it so much it upsets me daily. All I get is a sorry from Maytag. Its not that old, only a year and a half. Why no satisfaction? I will avoid all Maytag products for life.

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

I have an MSD2542VEB01 model refrigerator purchased slightly over two years ago. I have the same problem as many others, which is the plastic breaking on the shelves. The first time, it was within a year and the part was under warranty. It is now a year and a half later and one is broken beyond use and another is cracking again. Maytag refuses to help me as there is no “recall and the plastic is not available separately from the easily removable glass of the shelf. The least expensive price that I can find for the shelf is $107 and I need two of them. $214 (plus shipping) when all I need is two pieces of plastic? Be very careful when selecting your appliances.

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

I purchased both a Maytag Neptune washer and dryer in 2007. This is without a doubt one of the biggest mistake I have made. I have had the dryer drum and rollers replaced and the washer will no longer run. It is going to cost me hundreds of dollars to repair. To think I bought these units for 2 reasons: 1. that Maytag are the dependability people, but its not! and 2. Energy efficiency. It is not too efficient when they are broken more than they work. The worst was when the repairman told me that I had purchased the worst product on the market. These units are in short, garbage! I will never buy another Maytag Product!

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

I am a Baby Boomer... just like so many of us, I watched those lonely Maytag Repairman television commercials. Yes, silly me I purchased our top loading Maytag Bravos XL because of the brand name and because the machine was large enough to wash our bedding. Well, like so many fellow purchasers have found, this machine does not get the clothes clean and leaves soap spots all over the clothes. Its embarrassing. Additionally, there is that funny smell after the clothes come out of the wash. Well, Maytag has really done a number on us all. Kudos to their research & development department for creating a washing machine where the clothes come out dirtier. Has Maytag thought about a RECALL? I will tell everyone I know to NEVER buy a Maytag.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

I would have given this washer/dryer a 0 star, but wasnt able to. Bought the pair and first thing, couldnt get enough water in the tub, clothes wallowing around for an hour in the few cups of dirty water that it allows. Cant even believe how terrible this combo washer and dryer is! Now I get to wash everything in this piece of ____ twice, thank you Maytag! Just took out a load and it is dingy and stinks, so now its wet, on the floor waiting its turn to go back for another wash (possibly even a third).If you want clean clothes, do NOT get this washer. Dryer has issues also. For whatever reason, the AF signal has been on for a couple of months. Turn it off and back on and its okay for a bit, then back on. Its the Air Filter. Its not plugged, so I dont know, I just keep using it with intervals of resetting it altogether. What a total waste of money. Am going to give it away for free as soon as I find a replacement! Save yourself a huge headache and look elsewhere than Maytag. Oh, and if Maytag happens to read my review, you can contact me for a refund any time, just respond to this post, you can even come pick it up and get it out of my home. Thanks a bunch!

We purchased a Maytag Commercial Technology washer from Lowes. After having the washer for only 3 months, the drum failed, an entire load of clothes was turned black with oil, and my washer was out of service for months. The drum had to be replaced. They did not offer me a replacement. I was just without a washer. They couldnt get the parts because of supply issues created by Covid. I was offered a 2-year additional warranty which should have carried me through 2022. Last week, I called to use the warranty - service was scheduled (and I was told that I did indeed have a warranty by the service team.) I was then told by the repair team that I was out of warranty. Maytags notes show I was only offered a 1 year additional warranty. I talked with Management at Maytag/Whirlpool - they will do nothing for me. Shame on me for not getting that in writing. Shame on Whirlpool/Maytag for lying to me. The washer has been a nightmare! Dont buy one.

I have had this refrigerator for less than 3 years. It recently started leaking water on the floor and all over the bottom of the freezer. Repairman said it is a flaw with the defrost drain design. He thinks Maytag MIGHT have changed it since I purchased mine, but I dont know. Originally they used this small rubber valve;repairman said they get clogged very easily (even though I vacuum around it regularly and dont have any pets). He replaced that part with something sturdy that looks like a p trap. I looked online and there are loads of complaints about this exact issue with the defrost drain clogging. It cost $250 to have it repaired. I called Maytag to ask to be reimbursed and of course they will not do anything since it is out of warranty. Its a shame Maytag wont stand behind their products. Since there are so many of us with this issue, cant something be done?

Dishwasher (MDB7709AWB2) stopped running mid-cycle, internet search revealed that control panel needs replacement at a cost of $135. excluding labor, for a dishwasher that originally cost $348. Notified Maytag and am awaiting a response.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

The Maytag Bravos XL low water washing machine is very disappointing. About 20% of the time it needs a second rinse because there isnt enough water released to rinse clothing. Forget washing anything large. It just doesnt do it. Waste of money. The matching dryer is just fine - no complaints.

I researched gas ranges for a few months before choosing our Maytag gas range - it was on sale when we ordered it and it arrived within a couple of weeks. We wanted to buy local and were successful with price matching the sale price. I would recommend this range as it functions great and we totally love the larger oven door.

We purchased a Maytag Washer and Dryer from The Home Depot in September of 2017. We did not purchase the extended warranty because of our confidence in the brand. Within less than a year, both appliances started making noises. By September of 2018, the washer sounded like it had a bag of mice squeaking inside every time we ran a load and had stopped spinning entirely. I called and spoke to a very kind lady who assured me that even if we were outside the one year manufacturers warranty, they would offer us the extended warranty without question because it was so close to the one year purchase. She took my credit card, we were charged for a five year plan and service was scheduled. After service, both units were still louder than I would prefer but the technician said it was common. Over the last few months, both have become louder and louder. Now the dryer shuts off and wont stay on. When I called back to schedule service again, the date of our purchase was all of a sudden in question. (I applied for the contract over the phone so THEIR rep entered the purchase date.) They are now telling us they will only honor the cost of parts and we are subject to pay for diagnostics and labor (which is the largest cost of repair). They are telling us our contract has to be cancelled and AFTER we receive and PAY FOR all but the parts, we can call and pay for a NEW contract. This has been the WORST appliance purchase we have EVER made and we have lost all confidence in the quality of Maytag/Whirlpool appliances. Both units have been VERY disappointing and we spent over $700 on each unit. NEVER AGAIN.

Maytag washer, dryer, oven, microwave over-the-range - all crapped out in four years. I will never buy or recommend Maytag. I believed them to be one of the best brands but apparently theyve learned a few too many shortcuts.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

We purchased a Maytag refrigerator with bottom freezer and French doors, in March of 2015, Model No. MFF2258DEM00. Its adjustable shelves and adjustable door bins were big points in its favor, at least in my eyes. So far both the fridge and freezer cool fine. The automatic ice maker was never connected, so we obviously have had no problems there. However, within a few months of purchase the bar that supports--and provides tracks for--the vegetable and fruit bins broke. It was replaced, but within another few months it had broken again.This is a DESIGN DEFECT that wont be remedied by replacing the item. The bar, which is plastic, hangs from a thin lip about 1/2 long by 1/8 thick. Thats way too flimsy to support the weight of one bin, much less two. There is no way to repair the bar. The entire assemblage needs to be redesigned and remade from sturdier material. Its not simply the inconvenience of having bins that dont operate smoothly. With their track broken, the bins rest on the glass top of the meat and cheese drawer--and threaten to break that. Theyve already caused the door to that drawer to crack.

Bought the top load water saving washer 3 years ago and paid around $500 dollars for it. It will not operate correctly. I always thought Maytag was the best!! My main complaint is I cannot get no one on the phone to ask questions about what might be wrong with it!! Now Im angry, its like you buy it, its yours, we arent worried about you after that!! I am on a fixed income and no one cares!! Ill never buy anything manufactured by Maytag ever again!!

I purchased my which I thought was a stainless steel French door refrigerator in 2011 that I was getting a great product. Not even 3 months later I was using my warranty to stop the leak from my freezer now. Mind you, I paid $1500 so I got it fixed. 3 months later I called for repair again... Getting annoyed because this time the freezer came off track. 6 months later were chopping ice chunks up to stop the leaking on the floor. This lasted until last October keeping towels and old clothes around the fridge to soak up the water. This is so embarrassing especially if you have company over. You have a pile of crap soaking up water. I am a wife and mother of 7 children. I cant afford to just go buy another fridge. This isnt fair... I spent hard earned money on that magnet attracting stainless steel fridge and Maytag could care less. Im so disappointed and broke. Now I have to scrap it.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

Purchased Maytag dishwasher July 2013, installed August 2013. Stopped working Oct 2, 2014. Called Maytag and they offered to let me buy a service pan for around $300. No thanks, stupid Im not. I also sent an email. Have not heard back but Im sure Im still out of luck. According to the California class action suit regarding the Maytag control panels, Maytag is saying there are no problems with them. Wish we all had some power to make them see otherwise. Will I ever buy a Maytag product again. No. They would be much better off keeping their customers happy rather than spending tons of money on ads trying to get new customers. Since Maytag is owned by Whirlpool, they will not get my money either.

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

The $1,100 Maytag Bravo XL does not have a dedicated spin cycle. Its rinse and spin. When out of balance, you rearrange and it rinses AGAIN - 15 minutes - before you know whether its balanced. By rinsing again, it can redistribute to be out of balance. Repairmen (w/ extra warranty) said you cant wash bath mats, bedspreads or pillows though it had giant capacity! They would charge me if I called again about it (3 strikes). So bought a used Kenmore with no computer panel... Its great! My dealer had the Maytag hauled to a dump, he would not sell it to anybody as he had integrity.

Has had problems with machine being off-balance and clothes getting clean. 3 years and now the machine is broken. Too costly to get repaired. Warranty only covers very specific things. Have had Maytags repair person come out and he did not access the problem properly. What a waste of time and money! Says it needs a very expensive part which with labor and parts cost almost as much as machine.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

I had the washer repaired twice in January, once in April and again in August, the same repair wire coming out of harness. I had to pay a second time before Willie, the repairman, finally put a longer wire on the harness. Maytag told me they would send a new repairman after I called to complain. All 4 times, its been the same man and it cost me money. It seems like a bait and switch with the repairman. I called both A& E and Maytag. Both refused to refund the $129 second charge because it was more than 90 days. I say its been the same issue, repairman is a scam when they dont fix it right and charge again. I had another man there who knows about repairs and finally told the repairman to change out the wire or it wouldnt have been done this time either. I do want an attorney to contact me about this as this is wrong. Im going to file a complaint with BBB.

We purchased a Maytag bottom-freezer refrigerator MBL2258XES1 from Home Depot on 12/30/2011. Other than being a bit noisy, it functioned without problem for a little over two years after which we noticed water pooling on the floor, just below the left-front corner of the bottom-freezer door. It was shortly thereafter we noticed the large sheet of ice that covered the entire floor of the freezer. Over the past several months I pull out the large towel, my spatula, my meat tenderizer and break up and lift out the ice onto the towel around every two weeks. Thanks Whirlpool/Maytag! At least that Maytag repairman isnt lonely anymore.UPDATED ON 03/18/2015: I called Maytag Customer Service, (800) 344-1274 to discuss remedies for my Maytag/Whirlpool bottom-freezer refrigerator which has a perpetual layer of ice on the floor of the freezer which leaks onto my floor. I was offered a product called Repair Plus One which includes parts and service for this repair and they throw in a 1-year warranty. The cost: $359.95. The representative informed me I only had 24 hours to make up my mind as the offer was time limited. I asked if there were any other remedies available to me and she said none other than a service call.

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

Constantly does not clean clothes, always out of balance, codes constantly come up, only 2 1/2 years old and already rusting out. No matter what you do this washer does not want to work. Has special cycles for bulky loads but try to wash 7 towels and it will dance all over floor then shut down with an unbalanced code and you have to unplug to reset then wash towels again but not use spin and have to wring out towels by hand. I cannot believe the Maytag company has not recalled this very expensive pile of junk, and their service department is very rude and not helpful at all.Also as soon as you call an appliance repair company and tell them its a Maytag Bravos they say we do not fix those, do yourself a favor and junk it and buy any other brand. I have 3 kids now grown so we have bought about 5 washers over the years and when we saw that this was supposed to save water and energy and do bigger loads we were sold. Big mistake! Whatever you do never buy any appliance from Maytag. Products are garbage, service is nonexistent, and the cost will make you boil.

My Neptune dryer purchased in November 2005 had the drum crack at about three years old. I complained so much that they finally agreed to send a replacement drum for free. Now, two years later, the drum has cracked again and tore through the housing on the front of the dryer. The repairman said it would be too expensive to repair. Consumers, beware.

This is not my first Maytag. Bought this one in August 2017 from Home Depot. Now all it does is make a grinding sound. No lights. Not anything but noise. I bought one without all the digital because I thought that could be more problems. The only part that is digital is the start/pause button. I liked the idea of less water and no center. It balloons the clothes when it is finished spinning. Didnt start out that way. I use the right detergent and wash it every 30 days as it suggests. Cant afford to call a repairman on such a new washer.

Bought new Maytag French Door with cooling drawer refrigerator in July, & have had nothing but problems with both product & customer service since. Have already had 2 service calls for the SAME problem. The in-door ice maker/dispenser is a horrendous mess. Place a container below the opening to get ice cubes & ice is sprayed in chunks all over the floor & around the kitchen. To get ice, you have to put the container in direct contact with the opening, & then place a towel over the entire in-door unit to keep ice chunks from spraying all over the floor. The unit has a small flap-door in the ice maker, which must open & close automatically when getting ice, but the flap failed to close, so the ice in the ice maker was melting & the water running into the refrigerator unit & onto the floor. Called warranty repair & they came out & said they fixed the door-flap, but they did not. Ice was still melting & the freezer unit would not even keep ice cream & pastry items frozen solid. Called repair a 2nd time during the first 4 months of ownership, & they came out & replaced the motor to the small door-flap in the in-door ice/water unit. When asked why the freezer would not keep ice cream & pastry items frozen solid, the repairman stated (quote): Freezers dont keep ice cream frozen solid because it has so much sugar in it, its like alcohol. Had no excuse about the pastry issue however. We replaced a 12-year-old Jenn-Air with this piece of junk, but at least the Jenn-Air kept ice & ice cream frozen solid, & the ice maker did not leak & spray ice around the kitchen. Jenn-Air must know something about freezing sugary ice cream, that Maytag/Whirlpool do not understand. Then today we got a notice that Whirlpool had denied payment for the 1st repair visit, even though the unit was only 2 months old then. As such, we expect them to deny payment for this 2nd visit, even though the unit is now only 4 months old. Bad product & sloppy customer service, from a company with ZERO consumer support.

I was always told the Maytag was the best, to my surprise not so. We purchased a washer at Home Depot and it’s been a bad experience. Loud noise compilation in operation. Turns on then off so many times /not sure if that’s what’s its suppose to. Can’t get an answer. Disappointed for the least. Not what I expected out from this purchase.

2 major repairs in 8 years, ridiculous! We purchased a washer and electric dryer pair in Feb. 2012, had a repair for the control board (CPU) 4+ years under extended warranty, had another in 2018 for the same thing. I was told power surges could cause it, however I have a WHOLE HOUSE SURGE SUPPRESSOR ON THE INCOMING 200 AMP SERVICE AND KNOW THATS NOT THE PROBLEM!!! Had the same CPU go out again in Nov. 2020 so, rather than pay $370 for the part plus labor, we bought a top loading GE with an extended warranty and factory 10 years on the motor. We will never buy another Maytag product again. We were told that we shouldnt expect to get more than 6-7 years from a washer now, ridiculous. Manufacturers are outsourcing electronic boards overseas to maximize profit and could care less about quality control!!! Junk!!!

Maytag Bravos Quiet Series 300 - Our motherboard on the washer went out after 2 years from purchase - just out of warranty. Motherboard was $550 so we bought a Samsung. Now our dryer has gone out for the second time. First time was the pulley assembly came apart. We self-repaired after watching YouTube. Now the motherboard has gone out on the dryer! I will NEVER buy another Maytag product. They are a waste of hard-earned money and have left me with piles of laundry numerous times. Maytag, you need a class action suit filed against you!

I purchased the Maytag 6.5 inch electric convection oven about 2 years ago. I wish I hadnt. The oven temp is way off, it cooks unevenly, the back burners hardly work, and the back burners on the stove top barely work, the knobs get stuck constantly, the self cleaning does not work, and the glass part of the door allows dust to get trapped in the glass. The range is $800+ piece of junk, best used at the scrap yard. Today, I turn my oven on, and the element underneath the oven pan caught on fire. Now its broken in half, and needs to be replaced. I look up the QR code, and come to find out the oven is actually a Whirlpool, with Maytag labels on the outside. I would have never purchased this range if I knew it was a Whirlpool. I have always had issues with Whirlpool appliances. This is a fraudulent product, and deceives the customer. Why sell it as a Maytag, when its really a Whirlpool? It should at least state that fact on the description, and salespeople should advise the customer. Now I know why its a piece of junk, because its a WHIRLPOOL!!! I will never buy a Maytag or Whirlpool product ever again. I have always stuck with Maytag appliances. Every appliance in my house is a Maytag, or are they Whirlpool?

I bought a Maytag MDB8959SBS2 December 2013 with several major appliances for our new home while they were all deeply discounted and bundled with cabinets etc from Lowes. Moved in June 2014. Said dishwasher crapped out last month (May 2015). Buttons all fouled up, push normal and 6 other lights come on. Tried different resets, reboots, power down all no good. I ordered parts to repair, control board, control box, no luck. No warranty because purchase date was December 2013. This thing didnt last 11 months of use, and its just my wife and I running maybe 2 loads per week. I will certainly do more research and buy a foreign make/model or at least one not made by Maytag or affiliated brand. Unfortunately this supposed Made in the USA sticker sure doesnt stand for quality with this company.

Gas double oven - range that has performed well over 12 years old with only one service call for thermostat. Very inexpensive to repair and parts are readily available. Easily cleaned inside and out.

Purchased this Maytag dishwasher from a local Home Depot in Feb. 2014, no problems until now in late July 2015 (about 18 months). The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond.Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, can not be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only about three days ago. I assumed user error so let that cycle run, then was able to choose a different cycle (cant remember which one) which also completed. But since then the control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem, so will probably replace (with something other than Maytag) rather than repair.

I purchased a Maytag dish washer (not even 2 years old yet). I bought it on 8/29/10 and I paid over $400.00 for it brand new. The model number is MDBH949AWW1 and the serial number is F03422327. I am only asking for the part (motherboard). I have lots of friends and associates at church, work and social that I have talked to about this Maytag. And I would like to give a good report about the company and what they make and that they stand behind their workmanship. I know for a fact that they have 22 motherboards on hand ready to go out and what I have read online is that many people are having the same problem. I need a motherboard. I believe this unit should easily last over 10 years, so I am not asking for much. I will have it installed myself. I just need the part. I trust that you are a reputable company that has been around for many years and Whirlpool has taken new ownership and they have been around for a long time, too! My own parents owned one for over 30 years. This is all that I would request. I’m thanking you in advance.

Like the other poor reviews here- this Bravos top load washer is the worst. So wish we had returned it!!! There is never enough water in the machine on normal cycle to get all the clothes wet so how in the world would anyone expect the clothes to get clean? Just ridiculous - and whoever invented this machine, plus those who tested it, need to have their head examined! Hate it so much.

We bought a Maytag Neptune Washer and from day one in 7/10/2004, we have had trouble with the washer and Sears. First, it stopped working within eight months after we paid over 1300 for washer and master protection agreement. We called over and over from that day and was told we didnt show in their system as owning one and that we didnt get the master protection agreement. This went on and on until they finally told us on 8/2010 that they finally did find us in the system and that the agreement had ended a year before and would send someone (that was on 8/31/10) to do the washer. After having sat for almost six years, it reset itself and worked that day. I told the guy from A&E that it was the computer but that wasnt what he replaced so the washer went right back on in a month. So we had to save to have someone else come out from A&E to charge us 143.10 to say it would cost a total of 310.51 for the computer and that it probably wouldnt work for too long.

Buy this washer! It has the best features! No matter what the setting, your clothes will come out as dirty as you put them in, only with even more odor! I just cannot believe how many different settings they managed to program into this washer, each one delivering the same miserable results. I am so happy that I spent so much money on a washing machine, that in some cases, doesnt even get my clothes wet. Truly amazing technology!

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

Neptune 4000 washer - Worst washer EVER! Two weeks after we bought it sounded like a jet engine during the spin cycle. They replaced the bearing parts. Only cost us 450 in labor. One year later, again the bearing but this time we insisted on full coverage. 6 months later, here we are again! Most expensive washer in the history of washers and this is a KNOWN issue - yet Maytag gets away with it while consumers foot the bill! Ridiculous! Never again will I purchase their product and make dang sure everyone I know stays away too and everyone that hears my washer is in shock that it hasnt injured something or someone. Its only a matter of time!

Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We have had several repair calls. From reading complaints from others, I have the same: clothes balloon, clothes rip, dark clothes have a scum on them, even a blanket goes off balance and it is hard to start the cycle. It goes off balance all the time, makes a squeaky sound when agitating and the housekeeper can never figure out what cycle to run the clothes on because they always go off balance, there is a loud vibration, etc. The last repair call was for an actual leak on the floor! The appliance company charged us $95 for the service call, did nothing, and told us the parts would be more expensive than a new washing machine. Went to Home Depot today and purchased an LG washer and dryer for over $1500. I am not even going to try to recoup anything from Maytag because this is the second Maytag that I have had a bad experience with and didnt learn a lesson in the first place. Junk. :(

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

My Maytag washer MVWB400VQ was purchased four years ago and was used by two people. It started making a sound like an airplane taking off and is very loud. We called a service technician who said the outer tub was gone. I called Maytag to see if there was a recall or warranty of some kind. At that point I was told they do have a warranty but could not sell it to me because I had already had someone diagnose the issue. I paid $800 for the machine and the difference between the repair and the warranty was $40, so I thought it would be smarter to have some type of coverage if anything else went wrong. Nope they will not give you the coverage. The moral of the story is they really do not want to provide customer service unless you are unaware of the actual repairs needed so they can get more $$ from you.

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.

We had been a Whirlpool only brand household for as long as I can remember. When our Whirlpool washer and dryer gave out on us 11 years ago, we had a friend swear by the quality of Maytag appliances and decided to try something new. We purchased a Maytag Atlantis washer and dryer set. We have had our Maytag Atlantis washer and dryer since 2003 and both appliances are still as dependable and hard working as the day we purchased them. We live in a house with well water and our water is treated to be soft water.We have 2 daughters and 4 grandchildren who have come and put our machines through some heavy duty challenges when their non-Maytag brand washers and dryers have failed them. We are still very satisfied with our Maytag purchase some 11 years later, and so are our daughters and grandchildren!

Well Maytag, I have to say that I am very disappointed with your washer. When I put it on the bedding setting and try to wash a big load, it barely moves the load around. If you have a regular agitator to replace this useless one that is in this new washer I would like to have one. My laundry is barely getting washed and when you look inside the washer everything that is on the top stays on the top, not like the older washers where you could see that the laundry was getting sucked down with the proper agitator.

I bought the newest most energy efficient Maytag model M9BXXGMYM00 (for about 1K) from a local appliance store and after 9 months it wouldnt freeze. The local store picked up and left a loner for the fridge and made repairs in shop returning it in a week - great - except that approx. 11 months later the fridge again wouldnt freeze. The store sent repairman who charged 125$ to tell me it had leaked its freon again and would need repairs which were no longer covered under 1 year Maytag warranty. I asked the store to back their work but was only given a refill of the freon and half off the service visit. 2 months later the fridge is not freezing. I know because the repairman and store owner Mike told me that it had freon leak and that Mike himself had made repairs to the leak that the unit wasnt repaired.I have read that freon is toxic and can be hazardous to people with heart conditions and a list of bad effects. Maytag will only send someone to repair unit for a service call charge plus the repair charges and will not replace a defective unit. I can take the appliance store to small claims court over faulty warranty repairs but probably not the health risks - which are disputed by the experts. Ive read reviews and have heard from people who have appliance issues that the companies basically use a defective unit as a cash cow sending repairmen back again and again and never fixing the problem making a lot of money off of frustrated people who have bought a lemon from a company who doesnt back their product or their work. I was only looking for a decent refrigerator and paid plenty for one. I now have to get rid of a nuisance or pay to fix it - probably more than once and spend lots of time getting through the court vs. store owner process for any of the 1000 bucks lost on the defective toxic junk I got from Maytag.

Why is no one doing anything about the crappy product that Maytag is putting out. I am a single mom of 4 and I had to purchase a new refrigerator about 3 years ago. Spent a lot of money on this Maytag, approx. $1400 and it is now useless. I had nothing but issues with it from the time I got it. The bottom freezer kept icing up and then leaking all over my kitchen floor. I had to call a repair guy out, who charged arm and a leg and said it was fixed and 3 months later it was doing the same thing. Since I could not afford to pay ridiculous amount of money to repair it again (although I question what they said they fixed), I had to chop up the ice each month and take huge pieces outside and i had to keep towels always at the bottom of my fridge (yes very attractive) but it ruined my floor and carpet. Now all of a sudden the piece of junk just shut off and stopped working and keeps making this popping noise. Lights went out in front panel. So I had to call a service guy out again but this time I called an independent local guy that is not gonna rape you in charges like Maytag does and he told me to look into this that he has heard so many complaints that the front board with control button has been known to blow out the back circuit board, which is what happened. He told me that parts are MDs, so he would have to get another manufacturer and he heard that even with replacing both of them, it has been known to not work and Maytag takes NO responsibility at all for any of this. THIS IS WRONG. I cant afford to spend around $800 to now fix this or another $1,400 to buy a new one. So I am without a refrigerator. What a nightmare. MAYTAG, TAKE RESPONSIBILITY FOR YOUR CRAPPY PRODUCT. We are hard working people that spend our money and expect a good product. I also have an oven I bought and I can tell you it is a piece of crap too. I swear at it all of the time, as it takes forever to cook anything and the outside that is supposed to be stainless steel is all yoked up. It is like a tin can, looks horrible. I will never ever buy another Maytag product and I hope that ConsumerAffairs steps in and does something about this.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

I bought this washer less than 4 years ago and its already broken (leaking from the basket). Maytag refuses to honor their warranty and is charging $400 to send someone out to fix it even though it specifically says in the warranty that the basket is covered. When I mentioned this to the rep, I was told that does not apply to all washers. I expected better service from Maytag and thought it was a reputable company. I will now have to purchase another washer, rather than spend $400 to fix this one. It definitely will not be a Maytag!

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.

I purchased my home in 2008 at which time I bought all brand new Maytag appliances, well the above the stove microwave Ive had to replace the door handle because it broke off and the oven I can only use the very top or bottom to cook on and I cant move them, otherwise the racks will fall through. I have burned myself numerous times as I cant pull the racks in or out and I found that out cooking dinner and when I pulled it out the rack fell through and my dinner went crashing down and splashed everywhere. Due to this fact I hardly ever use it. I contacted Maytag with no help, told me to buy new racks and those did the same thing so it was a $100. It seems as though the liner cant handle the self clean heat and if you look at my oven, the left side is pushed in. If anyone gets help with this issue please let me know. My model number is MERH865RAS serial # 14348133LX. Oh and my refrigerator is a side by side and I have had to have it repaired twice because my food kept thawing out. That model number is MSD2651KES serial 60869476LV all of these are Maytag products and were purchased brand new from Home Depot.

I have a 6-month-old top load Bravo Washer. It has destroyed two bottom fitted king size sheets and 2 shirts that now have holes. It apparently slices the sheets during agitation. I have a service policy and called the service agency. The technician said there was nothing wrong with the machine, yet it literally ate 2 more items. Help! I need a solution to this problem.

Its a shame that I bought into the Maytag equals quality and customer service falsehood. Same problem as the others on this site and undoubtedly thousands of other consumers that bought a similar refrigerator freezer combo only to discover puddles in front of the unit and a 1 thick slab of ice under the freezer drawer. I contacted Maytag parts and when I described the issue he transferred me to warranty. The warranty department acknowledged this was a known problem and they would supply the part, no charge for the part but I would have to pay the serviceman to install it. They would not however, send the part to me to install. The unit is out of warranty, of course it develop the problem until right after the warranty expired. I plan to examine the drip pan and figure out how to improve on the design myself. I will not replace any appliances with Maytag, Whirlpool, Kenmore, or any other major appliances from this group of companies... Beware!

It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

Maytag Bravo XL -Model MVWB88OBWO. Washer quit after 13 months of light use. Repairman came, $148.00, worked on just a few setting for 4 loads. It has a bad controller and some other part. Total cost of repair, if I was stupid enough to make it, $650.00. Guess whats going to the trash. I guess that kind of negates the ECO-FRIENDLY, huh? I will NEVER own another Maytag appliance.

I bought a washer and dryer a few months ago from Home Depot Maytag. My clothes do not come out wrinkle-free. They are very wrinkled, to the point where I have to iron the perma press. The dryer I just got rid of was 30 years old, and always got the wrinkles out of the clothes. So I am very disappointed in the way yours works. I dont know what you can do, but this is not good. Thank you.

From the beginning, the blower motor (for the control panel? never needed one before) was too noisy. I just bought the oven from Lowe’s. They sent out a repairman. He replaced the motor, but has exactly the same level of noise. It is bad design/engineering. Im going to try some other brand. One problem is that you cant listen to the fan noise before you buy the oven and install it. And there are no decibel requirements or ratings. Industry regulations need improvement. Model MEW7527A, bought new in Dec. 2012.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

Just read Ann of Colorados (posting April of 2014) message about her Maytag Bravo washing machine and its like I wrote it myself! Our Bravo started with making a loud noise during the spin cycle which turned into oil or a dark liquid spraying out from under the machine, along with saying UL, so I would adjust the load and get it going again only for it to start the spin and rinse cycle all over too! We have 5 people in our family and cannot afford to not have a working machine. We purchased this machine only a few years back to replace another product that was also a piece of junk. I guess as a last resort I will try a Spin Queen which is American made and hopefully will work! Very disappointed in Maytag. Whatever happened to Machines lasting like they did for our Grandparents?

Recently purchased a washer from Home Depot. Machine is now on its 3rd repair. The wiring harness is fired. Could have caused a fire. Now they still will not replace and part is on order which will take 4 weeks to be in stock. I called Maytag and expressed my concerns to which they could not help me as every washer is theirs can be repaired. I really don’t understand what happened to making things right. Very frustrated that they will not repair or reimburse for that matter. Please refund my mom and pick it up.

I bought my washer just over 3 years ago and it started making loud clicking noises and it seems like the agitator function is not working at all. I have a repairman coming over in a few days. I knew I should have gotten the extended warranty!

Purchased French Door MF12269VM 22 inch from The Brick furniture April 1, 2012. Turned out to be a real April fools joke. Purchased extended warranty with TransGlobal for 5 years. First, fridge delivered after about a couple of weeks because it actually wasnt in stock. Naughty Brick lied about availability. Fridge arrives and after a service call from Maytag repair, they ascertain compressor doesnt work.Order fridge number 2. Two weeks later, get second fridge but lever for dispensing water is broken off. Order fridge number 3. Usual two-week wait and fridge finally arrives but the whole side panel is damaged. Send it back and order Fridge number 4. Service from Brick, Maytag and Whirlpool, terrible customer relations. Misrepresented delivery dates, supply issues, and operational damages.Fridge finally installed. Ice maker operates intermittently for the next year. Service techs from TransGlobal offer a variety of suggestions including changing filter, water pressure issues. Finally ice maker stops entirely in Summer of 2013. Is replaced after a month of waiting for parts of which the wrong part was sent. Ice maker continued to operate intermittently. Sometimes just a small of ice or no ice for a day. Finally in May after another service call, ice maker stopped working for about 4 days. Tech comes out and miraculously, it starts working again. A month later stops again and hasnt worked since.Contacted TransGlobal off shore call centre? And arranged to have an assessment to see if we needed a new fridge. Request declined and Maytag (Whirlpool) sent a tech out after another week. Service tech recommended new freezer. Waited a week for parts and arranged for Service tech to replace ice maker. Wrong ice maker part (for the second time) in less than a year.The latest trick from our possessed fridge is recent alarms from the temperature control. To say we are disappointed in this product, the retail experience, the quality of the manufacturing, the shipping procedures, the poor engineering and design, doesnt come close to describing the shoddiness surrounding this appliance and the service weve received.In conclusion, we are still awaiting an ice maker and are contemplating buying another fridge. What it is fair to say, we will never ever buy another appliance with their the Whirlpool or Maytag attached to it. Nor will we ever again buy anything from the Brick, or depend upon TransGlobal for repair services. Are there other Manufacturers and retailers out there who understand the meaning of service and quality. I certainly hope so. Otherwise Im going to invest in a good icebox.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

I bought my Maytag refrigerator Sept. 2013 and now in December, 2014 it is dead. After five visits from Maytag to repair it, they say it will cost $1,200 to repair it. The advice the man gave me was throw it out and buy something different. The refrigerator never worked right from the beginning. Four of the visits were in the warranty period. Compressor and evaporator shot. NEVER AGAIN. Maytag does not stand behind what they sell.

Maytag Bravo 300 Quiet Series - Bought this Maytag 5 years ago because Ive always had good experiences with them. After 3 years it started making rattling sounds so we had someone come out and fix it for around $275.00. 2 years later its still rattling, leaving black grease marks and putting holes in the clothes. Will not complete cycle unless it is unplugged, reset and plugged back in. I give up, I just bought an LG. I will never buy another Maytag washer again, still have the matching dryer though.

I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

My husband and I are retired. In 2006, we purchased a Maytag stove, refrigerator and dishwasher thinking we bought the best. Since purchase, we have had repairs on all 3 appliances costing us over $1000. We are installing our 4th electronic control touchpad replacement today at a cost of $250.00 each. We had a new oven electronic ignitor replaced on the same stove. The compressor on the refrigerator had to be replaced! The drawer mechanism on the dishwasher had to be replaced. We will never recommend or purchase your products ever again!

Bought Maytag dishwasher model number MDB894995BB3 serial # F41103073. About 2 months out of warranty the control panel went bad. Contacted Maytag. After quite some time they agreed to pay for parts. After some more conversation they also agreed to pay service and labor. This was on the first day of August and Maytag scheduled a repairman for the sixth of August. When he arrived spent five minutes and said he had to order parts. The control panel I had already told them was bad. Now here I sit waiting for part to arrive. No more Maytag or Whirlpool for me.