Purchased a Maytag - MDB7749AWM1 dishwasher in 2011 from Home Depot. The door seal has failed several times and been replaced by a serviceman. The warranty has since run out but the seal continues to fall out every time you run the dishwasher and open the door. Has anyone else had a similar problem? I have considered gluing the seal in place but cant find a glue that will handle the temperature. Im sure that Maytag will say they have never seen this problem before. Maytag is off my purchase list forever!!!

Purchased a Maytag washer and dryer 6 years ago and everything was fine until 3 weeks ago when the washer stopped spinning. We knew we were out of the 1 year warranty and contacted a repair service, who told us the bearing was no good. Contacted Maytag who offered in goodwill to pay for the parts and we would pay for the labor. A different repair person came in and told us the washer has no bearings but a transmission, which went bad. They ordered the transmission and today the repair person was in to install it. He installed the transmission, but while trying to take out the old one he dented the drum. According to my husband the repair person banged so hard that it sounded as if something could have been damaged, sure enough it was the drum. Contacted Maytag to see if anything can be done as now we still have no washer, and the repair person was their selection not ours. All we got from Maytag was they are not responsible and there is not much more they can do. I cannot believe the last Maytag product we had lasted over 20 years and this one is less than 6 years with problems. Will not purchase another of their products again.

I purchased a Maytag washer and dryer (Bravo series) in February 2011. The top edge of the drum in the washer is fraying. I contacted Maytag about the issue and never heard back. Now my dryer is not drying clothes. It feels like there is heat, but after 1 hour, the clothes are all hot and steamy, but still really wet. Our previous washer and dryer was over 10 years old and had no issues whatsoever, we just decided to upgrade to an HE W/D and now after just 14 months, the dryer doesnt work. They dont make them last anymore.

We purchased a Maytag refrigerator (MBF2258XEW) less than 6 weeks ago, and the compressor has already failed! Its not good, but the reason I am writing is their customer service (or lack of it)! We were told that it would take 3 weeks to get the replacement part, which was only 45 days old. Home Depot, where I had bought it, has been great; and they pushed Maytag/Whirlpool to agree to replace it. But Home Depot cannot not get us a new one until the paperwork comes from Maytag. We were told by their customer service that it would take 4 working days just to process the paperwork! Thats working days, and this is a Friday! So now, theyve all left for the weekend, and I still have no refrigerator and no idea when I will get one! They said no to getting the part faster, no to speeding up the paperwork, no to me returning it and getting a refund, and no to providing me with a rental. Please consider this when making any new appliance purchase.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

We bought a Maytag French Door 21 cu. ft. refrigerator in 2008. 2010, 3 repairs later, the ice machine went out, we went back to ice trays. Now the compressor died. The old ad of bored Maytag repairmen cause they never need repairs is bogus.

I purchased my microwave in 2012 and have had to have numerous repairs, mostly with the open/close door switch error. It is now 2018 and I see that the same problem is still occurring! Maytag obviously hasn’t read or doesn’t care that this problem has existed for years and they choose to do nothing about it. This past week when I had the microwave running, the beep went off indicating the popcorn was done but when I opened the door the microwave was STILL running! I thought it was a fluke but it happened again. Tonight the open/close door error once again appeared on the display. Having already had this repaired to the tune of over $150, not to mention the danger of a microwave running when the door is open, I called a mayday on the Maytag! I decided enough is enough and went out and purchased a new microwave... Obviously NOT a Maytag. The dangerous inoperable Maytag microwave is in the garage waiting for trash pickup.

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

Maytag Dryer MED6000XR2 - Purchased in Sept. 2012 - first service call 1/13/14; 2nd service call 2/20/2015 and less than one month on 3/14/15 it goes out again. It takes one week to get service company out and then another week for the part to be ordered and put in. This means I am without a dryer for over 2 weeks. An $1,100 dryer goes out every year and sometimes within one month?! According to the service company, it just is the way this dryer works. Really? If Maytag ever wants my business again, I better get a more justified reason and better than 2 weeks service call. This is absolutely ridiculous.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

I called Maytags customer service about an over the range microwave that was bought 2 years ago and barely used. The mechanism in the microwave on the latch for the door, clicked into the body of the unit and therefore the door does not register closed which doesnt allow it to come on. After explaining this issue to the customer service rep, she insisted that the only thing that Maytag would stand behind was the part if needed. A service call would be between $100 - $150. The microwave isnt even that old and why would Maytag not stand behind a like new unit? I bought 3 Maytag products and I am now regretting it. I had asked to speak to a supervisor and she just proceeded to repeat the same thing the sales rep did. They will only cover the cheap part if needed.What happened to Maytag being top of the line? Apparently they dont care about standing behind their products and would rather you buy an expensive extended warranty to cover their cheaply made appliance. I think they should be under review as a company. I would somewhat understand paying if my appliance was 5 to 10 years old. But its basically new. How is there no protection for customers when it comes to purchasing lemons from an appliance dealer? I will NEVER buy Maytag again and plan on selling my 2 other newly purchased appliances before they have issues. Maytags reviews on social media are terrible. All they offer are the words Im sorry and I understand your frustration. I assume thats just what they have written down in front of them to tell everyone who calls with issues. How do you not stand behind your products! I wish I could select no stars vs the 1.

I have to agree with all these other reviews. This washer twists clothes and does not wash them at all. If you open the lid mid cycle you will see dry clothes on top... Isnt that the whole purpose of a washer? WTF. Steer clear of Maytag. They realize that theyre selling washes to Generation Xers and they can get away with it because we were the first throwaway generation. Great business plan Maytag!

Recently I purchased a Maytag Bravo Washer and Dryer. These two items are the single worst appliances I have ever purchased. They are loud, ball the clothes into a knot and run forever. I plan to sell them on Craigslist and buy a Speed Queen.

Add me to the list of people who hate this washing machine. It does not use enough water to get clothes really clean, leaves spots, is hard on clothes and tears them up, and the spin cycle gets unbalanced too easily. It has taken me hours to wash one load with a blanket in it because of the spin problems. I have not been able to restart the spin cycle without starting the wash cycle from the beginning.

I purchase my Maytag electric glass top stove 9 years ago. 2 years ago, one of the burners went out and had to be replaced. Now, in the past 2 days, my oven is taking FOREVER to preheat from 0 to 455 degrees. So far, its been 78 minutes waiting for it to go from 0 degrees to 425! Apparently the heating element is defective. As far as the self cleaning oven, it is absolutely worthless, and does NOT work! Needless to say that Im very disappointed, and looking at another repair expense!

Maytag side-by-side fridge with water/ice dispenser (Model # MSD2572VEW00) was purchased in 2011. Mechanically, fridge is working, however, every piece of plastic inside the refrigerator section (the regular glass shelves with plastic rims, vegetable bins, and door ban shelves) are all cracking and falling apart. Additionally, the buttons on the ice/water dispenser fell off, exposing the actual buttons on the panel. All three of the regular sized shelves have severe cracks in the plastic that affect the sturdiness of the shelf. Both vegetable drawers are badly cracked, falling apart and one doesnt even stay secure on the track. Even all three of the door ban shelves are cracked with fractures along the sides and bottom. Weve resorted to putting clear packing tape just to hold the shelves together.We contacted Whirlpool, who owns Maytag and because our fridge is 4 years outside of the 1 year warranty, they could do nothing for us. In over 30 years of owning refrigerators, this is the first time Ive seen every shelf and bin crack the way this fridge has and in less than 5 years no less! Whirlpools solution to our issue was to send my call to their Parts Department. The total cost to replace all the cracked shelves, bin drawers plus the ice/water dispenser panel is $702.28. No thanks, thats as much as a new fridge. Whirlpool should be utterly ashamed of their total lack of Customer Satisfaction by distributing such a piece of junk. Who would have thought that an appliance costing a couple hundred dollars would be considered as disposable as an aluminum pan and in only 5 years! One thing is for sure, I will certainly think carefully again on ever buying another Whirlpool product again since they are so apt to take my money only for me to repurchase an expensive appliance again in less than 5 years.

Come on people are you serious! Im talking about all those people who give this washer great reviews or even mediocre reviews. This washing machine sucks! Thank God for the glass lid so you can see how terrible it washes. No water in this thing. Clothes that sit on the edge of the bowl do not agitate enough to be washed if there was water in the wash cycle. Bleach that you use in your white wash cycle is left over and gets onto your colored cycle if you wash it the color cycle next. I ** you not, mark my words that stains are left on clothes even in a cycle that has lots of water in it. If you think Im high or crazy take a look at your local Home Depot or Lowes store. Check the area for washing machines that are for sale that have been used. You will find this Maytag Bravos XL machine there. They look good and are practically brand new and they will be there for weeks on and because people return them if they get lucky to return them. I called my store and they refuse to take it back and told me to call the manufacturer. I did just that... I called the manufacturer and they told me they can send out a serviceman to check the washing machine. Butt...and a big butt, if they find nothing wrong with the washing machine that I will be charged a service fee. Bunch of **! For all of us that get stuck with this pile of garbage we can thank the tree huggers for trying to save the world with low water consumption water washing machines.

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

I really like the refrigerator. Its easy to maneuver and frost-free, but I should have gotten the side by side. Also, make sure of your family size before you make final decision. Other than the size I would recommend to family and friends to purchase.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

I had to rate at least a one star because there isn’t a negative to rate. We bought the Maytag mvwb955fc1. First off it doesn’t clean our clothes. I can not get stains out or whites bright. I don’t feel it uses enough water. I put a full load in and it only fills up less than half with water. I try half loads and still not clean. It’s always shutting off when I wash sheets. Indicating it’s off balance. Today I started it before work and the lid exploded. I don’t think I want to even replace it at all. This could have seriously hurt someone. Do not buy this washing machine. The dryer is great so far. I wish I could post a photo to show you all.

Purchased the Maytag Bravo Nov 2010 and had to replace it after just 5 years. In the five years we owned it, it required a new water pump and the stabilizers had to be repaired. Its motor burned up and I was not able to find a replacement. I was quoted $224 (parts only) for a replacement motor and 10 weeks delivery. My wife never liked the machine as it was not able to clean clothes that well. We did not find much difference in any of the settings. We tended to put very few clothes in each load in order to get them clean. We were dissatisfied that it did not have a soak cycle and the lid lock was particularly annoying.

We had perfectly working 20 year old top loading white Whirlpools w/ an agitator, when we remodeled our home and wanted new pretty grey appliances and decided to donate our machines to the church. I chose Maytag top loading due to their former reputation we experienced with dishwashers, etc. It had an agitator, deep fill option, extra rinse, etc. The sales person at Home Depot stated, the agitator is because people like you still want the agitator, and the deep fill will give you the water you have been used to. Not so at all!!Clothes get wound up together, even with filling the wash tub in bundles, there is almost NO water to thoroughly clean & the rinse cycle is a joke. Clothes do NOT come out clean. Im 58 yrs. old and have been doing laundry since I was 13 so I know what I am doing. Its just my husband and I now, and he is so upset that his clothes are pilling probably from rubbing together, even though I occasionally use laundry bags. I seriously wish I would have saved my money and kept the 2 perfectly working whirlpool units I had. This has been such a disappointment. I sincerely would not buy these.P.S. Weve had service out at least 5 times in the last year, and all they do is test the washer and tell us its working as intended... The last thing that is going to happen is we are going to get refunded for a different set, even though we were educated over and over what it would do by Home Depot associates. We are heartbroken. Maytag is going to lose their former reputation on these washers a dryers :( There is simply not enough water to clean or rinse things!

Bought a 2400.00 refrigerator 1 year and 4 months ago. The freezer quit working and we lost everything in the freezer. We called and were out of warranty. The commercial on tv shows the bored repairman who never has any work because Maytag is so reliable. What a crock! We are going to have to pay for the labor which could be as high as 800.00. This is so wrong. This is a high end refrigerator and the fact that it only lasted a little over 1 year is unbelievable. I would dump it if I could afford to. It is a piece of junk. I will never ever buy Maytag again. Make a new commercial, one where the repairman is so busy he works 24/7. We got screwed by Maytag. They do not stand behind their product, they rob you blind.

The Bravo HE Washer was a cheap piece of garbage and I am very surprised Maytag put its name on it. It broke down exactly one year after the warranty went. It did not ever clean clothes properly and all stains remained even when you spot clean first and double rinse. Maytag basically ripped us all off and somebody should start a class action lawsuit for this thing they call a washing machine! What a joke! I wont repair it. It will just fall apart again. Im not stupid. I know this is how they pay their employees doing house calls! So now, I have to go to garage sales and look for one made in the 1970s because that is when machines were made in the USA and things were built to last, not this crud. Maytag should be ashamed. It is time for them to close its doors. Sorry but its true. They are just crooks now selling crud that falls apart! They owe me a full refund.

This review is for a Maytag dishwasher. I do not know the Make/Model. It did a very poor job of washing the dishes. It may have been the city water, but no matter what I put into the machine to keep the dishes from being cloudy it never worked. It became disabled about a year after we moved in, and it was only about 6 years old. However, there were two families before me that used it and I have no idea how they used it. It was the first and last Maytag dishwasher I will ever use.

CHRISTMAS morning Set oven to 325 for ham. Control board caught fire and burnt wires and burnt inside of rear cover. It got hot enough to char the wood wall behind stove. This could have killed my family on CHRISTMAS.

I purchased a Maytag model 4000 Front Loading washer in April 2010 and in May 2011, the tub bearings went out which is a $600 repair. Now in January of 2012, the tub bearings are going out again. Neither Lowes nor Maytag are willing to do anything to remedy the situation. Do not buy Maytag and do not buy from Lowes. Their major appliance buyer has to know about this and continues to retail a product not fit for its intended purpose.

I bought the largest Maytag top load washer. From day 1 clothes come out with laundry detergent left all over them. I have to take a washcloth and wash off every piece of clothing coming out of the washer. Had a technician come out. He said he gets this complaint every day. His suggestion, put less clothes in and use less detergent. This washer is programmed to use minimal water and it just doesn’t have enough water to clean all the detergent off. So, I bought the biggest washer to wash bigger loads and now you are telling me that just doesn’t work.Spoke with Maytag customer service. They said very rudely if there is no problem found when the technician came out, there is nothing they will do. She told me it was user error. My dryer also stopped working. Sometimes it would turn on, sometimes not. The technician said the lint screen error code came up. He would try to get Maytag to replace the whole board but usually they don’t do that unless the whole board has a problem. Called Maytag the next day. The technician documented he fixed a connection problem and closed the ticket. What???? So, now I guess I need to schedule another service visit. Very unhappy with 5 month old appliances. Paid $1700 for the pair, you expect quality products.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

Maytag, you are still trading on your good name but that will not last! I owned a Maytag, agitator style, for 20 years and it was still running just fine when we built a new house. I thought it would be wise to buy new appliances for my new laundry room so I chose the beautiful and expensive Maytag Bravos XL. I regret that decision. The washer lasted 4 years and began to have problems draining last week. The liquid that stayed in the washtub until the repairman could get here was so foul smelling! He came back today to replace the drain pump and now the washer is showing that the interface and CCU are not communicating. So now we are ordering another CCU and I hope this fixes the problem. I agree with all of you who say you will NEVER buy another Maytag again. Maytag, are you listening?

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

The Maytag Dishwasher Model MDBTT50AWW started having problems cleaning dishes after about 3 years. I usually had to clean them first before placing in the washer. About 6 months ago (5 years of owning), some of the control panel buttons stopped working. Finally, the Start button stopped. Replacement part and service is about $400 per local appliance repair shop. They recommended buying a new dishwasher. They stated that the touch control panels have reduced the life of dishwashers to about 5 to 7 years. However, I had seen testimonials on the web of dishwashers lasting on average 9 years - not Maytags. I will be avoiding Maytag for next purchase. I have seen too many complaints online about the control panels dying. I consider myself lucky as my panel died after 5 years while many reviews say theirs died right after the 1-year warranty.

I had a Maytag dishwasher for 17 years, and it has still worked fine when we moved to another state. At the end of 2010, I bought a new Maytag (1) because my old one performed so well and (2) we left it at our old house. Well, slightly over two years later, this piece of junk (Model MDB6709AWAQ1) needs almost $300 worth of repairs. The repairman said they are no longer made to last and have been that way since about the year 2000. All of the inner workings are run by electronics which only last about two years. I said, What happened; the Maytag repairman got tired of sitting around doing nothing? I would never ever purchase another Maytag dishwasher, or any other appliance made by them or Whirlpool which took over Maytag.

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

I bought a Maytag dishwasher in Sept. 2013. This dishwasher looks great, but it leaves glasses stained with a cloudy haze. It also does NOT dry, even on jet steam dry mode. Bottom line, after a little research, I was the one who bought it, so I took accountability and just rolled with it. Well, the control panel stopped working this week (wont light up). I called maytag and the lady told me they would cover a service call and parts even though its not under warranty. When the service company called me, they said maytag will NOT cover cost, totally contradicting what the Maytag lady told me. After reading these other posts, I wish I would have visited this site before I bought this headache of a machine. I will never buy Maytag again!

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

I bought the Maytag because of its reputation and as a washer it hasnt disappointed me.. It gets my clothes clean with a minimum amount of effort on my part and it doesnt use a lot of water... I love my washer.

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

I have a Maytag Bravos XL and have white residue on all the clothes that get washed in this machine since I purchased it. I have always used HE Detergent and have followed all Maytags recommendations to reduce the white residue to no avail. I had to wash my clothes 5 times to get the residue off of my clothing and 4 of those were without any detergent and on all temperatures and wash cycles. Model # MVWB835DW.

Washer is Broken After 1-1/2 Years: Yes, the code F51 has come on quite often. Now, my washer does not work at all! Does not spin out, makes thumping noises even though I have taken good care of this machine. It cost me quite a lot of money and thought that this was a wise decision. It’s broken after a year, unbelievable! Also, clothes don’t get clean. I had to wash 2 - 3 times. The clothes wrap around each other and the machine does not clean them well. It’s a horrible machine. I have not called Maytag (Whirlpool) yet as I see from the comments that they will not stand behind their machine. I dont know what to do!

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

I have a Maytag refrigerator - the kind with the French doors with the freezer in the bottom and then the middle drawer is now leaking water all over my hardwood floors. This is ridiculous. Maytag better get off their butt. They need to send people out or send letters to people that have these freezers to fix them. When you pay a lot for something they should get a good product. If there a recall they should of send out letters or something.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

We 19 years and gently used. The door latch broke. We purchased a used quiet series Maytag dishwasher and found that the door latch failed on this. I recently found over 600 complaints for the same problem. If you are receiving this many complaints and its one of your most frequent complaint, do you think its time for a redesign of the door latch mechanic is??? Or are you relying on your reputation and dont care about quality anymore?This is it for Maytag. Im glad we didnt buy a new Maytag because we would be stuck again with a crappy door latch. If you cant be bothered with fixing your door latch issues and you know that you have a long term problem here, you at least can send a new door handle kit to those of us who are complaining. Of course you wont do that. And the only recourse I have as a consumer is to tell others about the ongoing problem with your front door latch on my social media. Sadly, you are now only another crappy dishwasher with no real quality control. I bought several appliances from you because of your reputation for appliances that last. Seems that is now a myth.

I bought this washing machine approximately two and a half years ago. I replaced the agitating wash plate three times. After several months, the wash plate will start free spinning from the gear and will spin like a top. It has to be replaced at $140.00 plus the service call. When it was working, it doesnt clean the clothes well. I contacted Maytag numerous times about this problem and they basically gave me a tough luck answer. I just went purchased a old style machine with a tall agitator that will clean like its suppose to. Its a shame Maytag has no compassion to try and compensate customers for the expenses. I also contacted Whirlpool which took over Maytag. My rating is a negative five.

The control panel of my dishwasher is malfunctioning. I looked this up online and ran into a recall for the heating element. Sure enough, my dishwasher is effected. I asked why I was not contacted. First they made up a story as to not having my contact information. This is simply not true, as I purchased the dishwasher directly from Maytag. Three years ago there was another recall and the heating element caused another problem so Maytag replaced my dishwasher.If a heating element overheats, it seems to me that a short-term affect could be overheating the control panel, causing it to malfunction. I read through a few recent complains and would also like to inquire about having this issue looked into by the Consumer Affairs.

The unit has an ice maker. On a regular basis, water would accumulate at the bottom of the freezer pan. When the bottom pan got filled up, water would run out on to my hardwood floor. I related the problem to the ice maker. Researching the problem, I learned that the ice maker has an adjustment for timing the on cycle for filling the ice tray. After several adjustments nothing changed. I ordered a water control valve and installed it. The problem persisted. I installed a water pressure regulator but the problem persisted. I installed a water filter, the problem persisted. I turned off the entire ice maker and the problem persisted. The problem wasnt the ice maker. The real problem was the defrost cycle of the evaporator. The drain for the water was plugged with ice. I made modifications to the design so I could monitor the drain hole in the back of the freezer. Will I purchase another Maytag… probably not?

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

JADE model RJRS4270. Had this model for 10 years with more than 10 service calls. Always breaking down and Whirlpool will not honor the warranty. Paid for an extended warranty service to Maytag/Whirlpool offered by the manufacturer. When unit broke Whirlpools warranty service provider Assurance said Whirlpool no longer provides the parts needed, sorry can’t honor the extended warranty you had paid for, no parts, and no refund. The evaporator drip tray had been replaced three times. Asked to have the unit replaced. Whirlpool was absolutely disrespectful and only offered me to the option to buy another discounted $8K unit for a with ~ $2K discount.So far approx. $6K unit + approx. $1K extended warranty (not honored) + approx. $1K parts and service out of my pocket (Whirlpool continued to tell me it was not warranted). Although the operator’s manual said it was covered. While under warranty Whirlpool doesnt have replacement parts to service it. Multiple service tech are telling me there are many known issues with this unit. Found out there’s class action law for the same issues Im experiencing. Whirlpool only offered a new unit at approx. $6K. So total for me to date if I choose to take the discounted unit would be $12K. Dont buy this unless you have a good lawyer. Hardly seems reasonable. Extraordinary time/money loss and aggravation.Bought 8/1/05 S/N ** Model RJRS4270C $5,400. Service call 5/10/06 Repair - Freezer dripping water and pooling on floor. Service call 6/28/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/5/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/12/06 Repair - Unit not defrosting. Service call 8/26/06 Repair - Freezer not cooling, ice backup, fan burn out, drip tray. Service call 9/2/06 Repair - Evaporator fan not working. Replaced unit 9/_/06 S/N ** Model RJRS4270D. Maytag Dependability Plus Cert No. ** $99.00 8/02/08 thru 8/02/11. Maytag Extended Service Plan Plan No. ** $297.19 9/02/09 thru 9/01/12. Maytag Extended Service Plan Plan No. ** $405.31 9/01/12 thru 9/01/2015. Service call 10/13/10 Repair - Ice build up in fan, freezer not working. Service call 10/20/10 Repair - Installed new drip pan, bi metal, fan motor. Service call ~ 8/_/15 Repair - Service tech states, Whirlpool no longer has parts. Even though we paid hundreds to have a still active Maytag contract extended warranty. Whirlpool outsourced service to third party. Service call ~8/_/15 Service tech refuses to repair because cant get parts from Whirlpool. Asked me to find part on eBay or some other source so he could repair since Whirlpool could not provide. Got part. He did fix. Freezer stopped working 4/2/16. Customer support 4/3/16 followed owners manual instructions for warranty and call number, Whirlpool said theres no warranty and to call any local service tech. (Owners manual said compressor was still under warranty). Service call 4/4/16. Tech refused to work this Whirlpool unit, believes to be issue with the compressor leaking or system blockage or bad valve in compressor. Customer support call back - Krisi, was warranted. Jade Specialty Department. Customer support call back - Jared, no warranty, sorry. Explained contract to him. Nope/Nada. Customer support transfer - Jan, yes was warranted. Asked to speak to manager/sup. Said if you won’t honor warranty then please provide replacement. Transfer to Mike said we must schedule service through Whirlpool to fix contradicts. We asked for reference number to track. Mike said they don’t use reference numbers (contradicts Jared from when he asked me for a reference number). Two days no call from Whirlpool. Customer support call back 4/7/16 - Kari, offered small discount for equivalent new or refurbished unit $5,739 for Model KBSN602ESS. Said although under warranty, Whirlpool may not be able to provide parts to repair unit, but they will sell me an equivalent unit.

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

My experience is very similar to Richards below. I have an MDBH979AWS3 that was purchased new in April of 2010. Just over one month after my warranty expired, the touch panel ceased to work. Since it was no longer in warranty, I had to replace it out of pocket. The wiring harness to the old panel looked heat damaged. Last winter, the central computer died. The machine was useless. I called Maytag customer service and actually seemed to find a sympathetic ear. They agreed to a new part if I paid $129 for one of the two companies doing certified repair to install it. During the summer, it blew several fuses. Then in late November of this year, the touch panel went again. I hesitated on how to respond and waited until after the holidays to call them. I got the most rude customer service rep that Ive dealt with in a long time. Somehow, I was blamed for a misdiagnosis on the computer panel (duh, no, that was a different issue and it was indeed broken), accused of misuse of the dishwasher, and flatly told that they werent going to do anything more on a machine. So far, out of warranty. Im sorry, but I cant accept that a machine under 3 years old should have 3 major failures. Maytag has to step up and at least look at this problem. From what Ive read, this is a common problem that has resulted in several fires. Maytag has to know about this and continues to do nothing, not even issue a recall on the current touch panel used. I am now faced with putting another $100 in (which puts me at about $350 total on a machine I paid almost $500 for) or just buy a new product. Rest assured I will never buy another Maytag-Whirlpool appliance.

I have owned several dishwashers thru the years and my favorite is Maytag. Maytag is quiet, barely hear it running which is rare for a dishwasher, dependable and plenty of space for dishes, pot and pans etc. I wouldnt have any other but Maytag. Also has several options for dishwashing which is a big plus. Love Maytag!!!

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

6 week old High Efficiency Washer leaves lint and soap lines. Ive tried deep water wash plus the 2 rinse settings and I still have to wash the load twice to get rid of the lint lines and soap lines. Ive also tried every combination of settings to no avail and I follow the guide to a tee because this machine actually weighs the clothes to determine the water level. Maytag customer service was polite but useless. Im assuming its the poor design but customer service says I will be charge for the warranty service call if no problem is found. Maytag, another fine company down the drain. PS, parts are made in China.

Purchased a Maytag fridge in August of 2010. Had issues January 2014 - needed a new circuit board. At the happy cost $230.00. Well it is now May 2014 and had to have the repair man here again for another circuit board $258.64. Maytag will not stand behind their product or parts they use in their products. They flat out told us that we shouldnt have to replace the circuit board that often and then said they wont stand behind it. So buyer beware. DO NOT BUY ANYTHING MAYTAG!!!!!

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

MDB8959SBB. Purchased this Maytag dishwasher late December 2013 and had it professionally installed on January 4, 2014. Could have burned down the house this weekend! Smoke everywhere! Thank goodness it was running during the day and not night so that we were able to shut off the power. Lights in the kitchen were blinking and smoke pouring out of the dishwasher. The house still smells of smoke. So disappointing. Ive always been a proud owner of the Maytag products. Never again. Especially after reading the reviews. Interesting enough, THIS dishwasher was purchased because of a recall on the PREVIOUS Maytag dishwasher I had trouble with. They gave me a credit to use towards my next purchase. Ive learned my lesson.

I purchased a Maytag Bravos XL Top Loading Washer and matching dryer in 2013. I had a repairman out to install a new screen on the dryer because the lint was spilling over into the surrounding area. The new screen has been catching most of the lint, but I still have to vacuum the surrounding area after a few loads. Also, I have to turn the dryer on two (2) cycles in order to dry most of the clothes, and the machine makes a lot of noise. Those are minor problems compared to the washer. It constantly tears holes in my towels and wash clothes. I NEVER put in a full load because the water level is so low, and it does not clean the clothes. It takes a long time to go through cycles and it is EXTREMELY noisy.I called Maytag and they said that they never heard of the problem of creating holes in towels and wash clothes, and wanted to charge me over $100 to have a repairman come out. They also said that the repairman might not find anything wrong. I feel that the washing machine is very hard on the clothes - like the salesman at Lowes said It’s like beating the clothes against a rock. The washer and dryer are JUNK, and I would not recommend these to anyone! I would trash them, but they were very expensive and we cannot afford to buy new at this time.

The only complaint is the lights on the bottom quit working about a month after we purchased. It was nice to light up the stovetop when cooking. Now it’s slightly dark. I have gotten used to this. We spent about $8000 on all the matching Maytag appliances we purchased. I would love to replace all but not in the budget. I am a dissatisfied Maytag customer.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

Well, my washer is 2 years old, yes thats right - 2 years old. And it only goes to the wash cycle, washes once and stops, wont complete a full cycle. Yes, the brand with the commercial with the repairman just sitting around because their products are so great you never have to work on them. Yeah right. And Ive seen videos on YouTube on the problem with the Maytags. So Maytag may want to look into it!

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

I purchased this $857 dishwasher from Lowes in May, 2021. It broke in June, 2021. S&S Repair was sent by Maytag to repair. It took 3 weeks for them to come, then they discovered the motor and pump assembly had gone out. Parts were on backorder. It is now August, 13, 2021 and I still have no dishwasher. Lowes would not replace this dishwasher. Maytag will not authorize a return. This is disgusting.

A few weeks after I purchased my Maytag MEDC300 dryer in April 26, 2009, I noticed it gradually did not dry as hot as when I first used it but the element did not go out totally until April 2011. Now its November 2011 and the element is out again. Maytag is sending a service man, of course I have to wait until Monday, I am now inconvenienced 2 times in a year.Theres also what appears to be a burn mark on the back of the drum. Two years ago, I paid more than $400.00 for this thing and when it does work, you have to run it over and over again to dry your clothes. Wow! really energy efficient. What a piece of junk! I had my old dryer 10 years before an element went out. I did buy the Lowes protection plan that was sold with a No Lemon Policy. If the product requires more than 3 repairs for the same failure, theyll replace it, it says in the front of the brochure.In the small print on the back, it states 3 repairs for the same failure in one year. These companies are making money off us consumers who buy Maytag because of the name and what is supposed to be quality, and are ripped off by these insurance programs that say one thing but another in the small print. Big business is nothing more than robbers who get away with robbing the hardworking American people. When is it going to stop?

I wrote earlier about my dishwasher needing to have an electronic board replaced again. So I called the helpful (I say that with sarcasm in my voice) 800 number. My dealer asked me to call for help with paying for the new part. After an hour and a half of being cut off and put on hold, I finally got through to a person that could take my request. The gentleman explained to me about why they would not stand behind their product which was only 3 1/2 years old, and a replacement part that lasted only 11 months. He expanded on his thought about how it was too old to fix and the part was more than 90 days old. I am out of my $1,100.00 with no help in sight. Totally upset with this company and how they will not stand behind a poorly made product!!!!

Purchased the Bravos XL top load washer a month ago. We work outside daily and our clothes get very dirty. I havent really taxed the machine yet (Im doing what I consider a normal load of wash. I know the machine could handle twice as many clothes as its the 5.3 cubic feet washer, but I havent had that many clothes to put in at one time). The washer works great. Clothes are clean and smell fresh. For those that say this washer is extremely loud - you must not have something set up incorrectly. Either the wet pan you put under the machine is making contact with parts it shouldnt or someone didnt level it properly. Really, this is NOT a loud machine. We purchased from Lowes and they delivered, set up and leveled both the washer and dryer. (Yes, we also purchased the matching Bravos XL front load dryer and were impressed that it dries our clothes in half the time our old one did). We would definitely recommend the Maytag Bravos XL washer and dryer.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

After 1 year and a month, the dishwasher would not work. When the Maytag repairman came, he told me that this was the 3rd one this month that had the same problem (the control panel). The cost to replace, it would be about $275. However, since I know of 3 that have broken, why would I replace it? I live alone and maybe have used the dishwasher once a week. There should be a recall on this machine. I called to see if there was a recall and was told Im sorry. I would advise anyone purchasing a dishwasher to avoid Maytag or any dishwasher made by them.

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

After my divorce, I bought a new house for my youngest son and me. It came without a fridge, so I used some of my settlement money to buy one I had been dying to get - stainless, French door, with bottom drawer freezer! It worked fine for the first 9 months or so. Then, water started pouring through the ceiling of my downstairs master bedroom. Turns out it was coming from the freezer water line. Ceiling tiles ruined, carpet stained. Then it started making this god awful noise. It starts, rumbles for a while (long enough to wake everyone up or give the dog a coronary), then is quiet for a while. Next, I open the freezer to find a sheet of ice across the bottom of the drawer. I assumed I had done something, so I got rid of it and thought nothing else of it. Last night, I get ready to make dinner and there is this blizzard of frost all over the freezer. It looks like a winter wonderland. I am afraid to see what is there when I go home and even more fearful to attempt to use my warranty.

Worst washer ever. My clothes I have to wash a few times before they all get wet. Not a good washer at all. Has all the bells and whistles. Lets me know when the washer is done or its unbalanced... my washer is crap. Ive had it maybe a year now. I now have to buy another one. Why? Because this one sucks literally... its Maytag commercial technology.

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

I bought this new washer and dryer pair at Lowes August 2018. I chose this brand because of the very large wash tub (5.3 cu ft) since I have king size bedding. My previous washer was a front loader, and there were problems with the door seal molding and stinking, and loads had dry spots on them after washing. So within a very short time, I realized I hated this new washer. Very noisy, no agitator, very long cycles. You cannot adjust the time or water levels, and the biggest problem... I CANNOT REACH THE BOTTOM OF THE TUB! I had to steal the grabby toy out of our toy box to pull the wet load out! The laundry comes out all tangled up and horribly wrinkled, even when using the wrinkle-free setting. I line dry a lot of my clothes and now have to iron everything. Never had to do that before. I know Im stuck with this set, but will look forward to the day when it dies and I can buy new ones again.

I was sooo excited to get this very very very expensive washer and dryer only to have the worst disappointment and let down...the washer in particular is horrible!!! It doesn’t wash!!! I thought I was crazy until I started reading all of these other reviews and found that many more people have had the same experience as I have... The tub never fills with water and the clothing never gets clean. I would love to start a class action against Maytag and get my money back or get a replacement.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

1. can not get enough water in the Maytag machine to cover the clothes. 2. All of the clothes come out twisted. 3. After watching the machine wash the clothes I notice that agitator did not move all of the clothes down into the water, and that was probably because there was not enough water in the tub. 4. The machine gets out of balance easily and at that time the machine door is locked and you need to push the pause button and wait for it to unlock the door. 5. Its louder than my old Kenmore washer that we have had for 15 years.6. The Maytag dryer does not dry as fast as my old Kenmore dryer that we have had for 15 years.Bottom line is I would not buy another Maytag product. Do your homework.