I spoke with Mike today at the customer service department at Maytag to see if Maytag would pay for the parts to repair my 04/2010 Maytag front load washer (model MHWE450WW00). The bearing assembly needs to be replaced. So, that means the tub and basket need to be replaced too. The original cost in 04/2010 was $1,088 plus tax. The cost to repair is $1,048. Maytag will do nothing since it was purchased over 12 months ago. I cant believe I just threw almost $1100 away on a washer. Obviously, there is something wrong when an appliance doesnt work after 1.5 years.

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

Ive had this Maytag microwave for about 4 years and the magnetron had to be replaced. The keypad was replaced three times due to SE code shutting down unit which happened again. When I explained this to Maytag, they said it is out of warranty. I explained to them that the last keypad which was replaced was only 6 months old. They replied but the unit is out of warranty! I would never recommend Maytag or any affiliated companies to anyone.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

I purchased my microwave in 2012 and have had to have numerous repairs, mostly with the open/close door switch error. It is now 2018 and I see that the same problem is still occurring! Maytag obviously hasn’t read or doesn’t care that this problem has existed for years and they choose to do nothing about it. This past week when I had the microwave running, the beep went off indicating the popcorn was done but when I opened the door the microwave was STILL running! I thought it was a fluke but it happened again. Tonight the open/close door error once again appeared on the display. Having already had this repaired to the tune of over $150, not to mention the danger of a microwave running when the door is open, I called a mayday on the Maytag! I decided enough is enough and went out and purchased a new microwave... Obviously NOT a Maytag. The dangerous inoperable Maytag microwave is in the garage waiting for trash pickup.

We just received a Maytag delivered by Home Depot. THe box the diswasher came in was soaking wet. I called within 30 mins of delivery to report this. Home Depot called and Maytag refuses to replace the diswasher stating that it comes wrapped. No it does not, the diswasher and insulation were soaking wet. Maytags response is just let it air out. So Im supposed to air out a 470.00 brand new dishwasher. Home Depot is also getting its one star review for refusing to replace it and letting the third party contractor get away with delivering a damaged unit.

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

First we bought the washer and not even a month after it was ruined. In the span of the year that weve had it, it has broken down about three times. Then we bought the matching dryer in August and by the beginning of December it has broken down. Called customer service and they are not coming until January 18. Have me waiting over a month to fix it. Worst brand ever and even worse customer service. Never again will I buy anything from this brand.

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

After having issues with bearings in a front load of another brand, we decided upon a top load Maytag. We have had it less than a year and we are not happy with the performance. We are using more detergent because the dispenser seems to be bottomless. Only the front of the little pull out drawer is visible and it never seems to reach the fill line when adding liquid detergent. There is no quick wash cycle. Not everything needs a cycle of nearly an hour or more. The spin cycle does not remove nearly as much dampness/water as our previous frontload. The drum is deep making it difficult to retrieve small items such as socks. My biggest disappointment is finding lint residue on the clothing and it remains even after an extra rinse. This is especially visible on dark clothing. Even the lint filter in our dryer fills up much more quickly than before. After researching, I found that others complained of this same problem.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

Like many I have never wasted my time writing a review, this time I have had it. Purchased all new appliances from Maytag, biggest mistake I have made in the last 10 years. Front loading washer is the main culprit. Doesnt clean clothes, have had to replace the rubber boot on the inside twice now, machine is only 3 years old. Maytag basically treats you like youre stupid, resend instructions like that will fix their broken P.O.S machine. I will never buy another Maytag and will be sure to let everyone know what a piece of garbage, from machine to company! Sad that the overall reviews on my machine are 1.3/5 stars on Maytags own website. Oddly, I cannot write any review on their site, Maytag must have realized what a POS theyve been selling and now block reviews. Im thinking that we should get enough owners together and file a class action lawsuit, maybe that would change their tune??? Never BUY MAYTAG, PLEASE keep in mind THEY are UNDER AN UMBRELLA with WHIRLPOOL and MANY OTHER MAJOR PLAYERS... Do not let them scam you the way they did me! If you work hard for your money spend it on a more reputable brand that will not try to stick it to you because they build junk!

This is a Maytag Neptune MAH8700AWW. This machine has been repaired a couple of times already and it has a will of its own. When it goes into that fast spin cycle that will kicks in and it starts moving. I wonder if someday its going to attack me. So, last Friday night we put a load in and it went into that fast spin cycle. It was making a noise like an elephant in labor so I looked in the laundry room.... Clouds of smoke were billowing out of the top of the machine. Our house will filling up with washing machine smoke! My husband stopped it, but I think it was a gnats hair close to bursting into flames. He looked into the front of the machine when the smoke dissipated and the entire gasket was in shreds. No more Maytag. Never. Im done.

For the first time I bought a new washing machine in order to have one that lasted. Bought a brand new Maytag Front Loading HE washer model MHW3505FW1. Controls stopped working and the machine turns on and off by itself. Its either a faulty control board or computer, either of which are going to be more than a $400 repair. So more than half of what we can pay for a new machine. Maytag only warranties two parts for more than a year. So in reality, its not worth the repair and I will not buy a Maytag of Whirlpool product ever again.

I purchased a Maytag washer and dryer (Bravo series) in February 2011. The top edge of the drum in the washer is fraying. I contacted Maytag about the issue and never heard back. Now my dryer is not drying clothes. It feels like there is heat, but after 1 hour, the clothes are all hot and steamy, but still really wet. Our previous washer and dryer was over 10 years old and had no issues whatsoever, we just decided to upgrade to an HE W/D and now after just 14 months, the dryer doesnt work. They dont make them last anymore.

I have a Maytag dishwasher MDBH980AWQ10, within the 1st month of owning it there were issues. Now the electronic control panel is shot, dishwasher wont turn on. To replace it...almost the cost of what I paid, warranty has run out. In the last 7 years we have had problems with 5 various Maytag products, replaced our Maytag dishwasher which lasted 20 yrs and Maytag washer & dryer that lasted 30+ years and ran without a hitch. Maytag has not been helpful at all and their authorized service repair. A&E Repair Service is a bigger scam than they are. It is a waste of my finances and time to buy major appliances every 5 years. Each and every one of their new appliances has died shortly after all the warranties have run out. Im beyond frustrated, disgusted, and financially drained. It does not pay to be brand loyal to Maytag for they are no longer respectful nor appreciative of their customers. I would love to give corporate the opportunity to enjoy the same products that are in my home...in their homes...as well as the experience of their customer service. Last Maytag purchase for me! Is there anything that I can do in the meantime so Im not stuck with their lemons?

We had a three-year warranty which expired. We used a repair once for a rusting Clorox basin. Now, the tub swings wildly on every wash and will not complete because we get the UL warning. Weve tried making sure the washer was balanced but confirming that nothing helped. Most expensive washing machine ever and shortest life apparently.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

I bought a Maytag refrigerator model MBB1953XEW three weeks ago. According to its features on the Maytag website, its supposed to be quiet (QuietSeries 100 sound package). Ha ha, make me laugh. Its the noisiest refrigerator Ive ever had. The repair guy checked it out this morning. He spent about 5 minutes running some sort of test with the help of his iPad. He then told me everything was perfectly alright, the noise was normal for a Maytag, and that I was going to get used to it.Needless to say, he had a totally condescending attitude. Its the first time I ever bought a Maytag. Previously, I had a General Electric that was noisy but not as much as the new Maytag. Prior to that, I had a good old Kenmore that was perfectly alright but that I had to give away for other reasons. This time I chose Maytag because I thought it was good quality and I wanted it to be very quiet. Well, nope. Next time, for sure, it wont be a Maytag.

Christmas sale, needed a washer. Had a great experience with Whirlpool Duet so went for the on Sale Maytag Bravo MCT. No agitator which I thought odd. Bought the warranty. Did no good as soon as I hauled the washer home (3-hr trip one way). It wasnt washing my clothes clean. Hubby said try different cycles and soap and temperatures but at 8 months pregnant it wasnt long when I didnt fight with the machine but focused on a very busy life. Baby number 7 and I didnt care how the clothes washed as long as they didnt stink. Well baby is older, the warranty is not over and after much dialoging, no one will do anything for me. I put muddy pants in, they come out muddy. I put cloth diapers in, they come out smelling like pee. How hard can it be to come up with a machine that just turns clothes round and round with a little soap and water? Apparently really hard as Maytag failed to test this machine. Maybe city folk just have lightly soiled but on the farm with 7 kids, my kids play hard and their clothes are very dirty. They continue to stay dirty unless I wash them twice on Power Wash and Extra Heavy Load. Not impressed. Would like a replacement washer of equal or lesser value, anything that works. Oh P.S. I have the receipts and order number. Sorry its not put online to be verified buyer but dont feel like digging for paperwork at the moment.

In August my GE refrigerator of 22 years bit the dust. Went to our local appliance center and purchased this unit for $2100. Have only had it a month and am so dissatisfied with the water dispenser, ice machine and doors, I want to return it. I cant wait for all the other things to go wrong with it. I dont know who the engineer was behind this but he needs to be fired. I really wish I had reviewed this refrigerator before purchasing it as I will never recommend Maytag again after reading all the bad reviews. The name Maytag used to mean something dependable and made well... Rant over.

I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

The control panel went bad on our Maytag dishwasher of only 4 years that is only run about once a week, A replacement part would cost more than half of what the dishwasher originally cost, so we have decided to go with a KitchenAid. Not pleased at all with the longevity of the Maytag.

My husband and I are retired. In 2006, we purchased a Maytag stove, refrigerator and dishwasher thinking we bought the best. Since purchase, we have had repairs on all 3 appliances costing us over $1000. We are installing our 4th electronic control touchpad replacement today at a cost of $250.00 each. We had a new oven electronic ignitor replaced on the same stove. The compressor on the refrigerator had to be replaced! The drawer mechanism on the dishwasher had to be replaced. We will never recommend or purchase your products ever again!

I have a Maytag refrigerator - the kind with the French doors with the freezer in the bottom and then the middle drawer is now leaking water all over my hardwood floors. This is ridiculous. Maytag better get off their butt. They need to send people out or send letters to people that have these freezers to fix them. When you pay a lot for something they should get a good product. If there a recall they should of send out letters or something.

I bought this POS and paid almost 1000. Out the door with tax, hoses, delivery, etc. And it is by far the worst most useless pile of crap I have ever purchased. It just does not work!!! Its a washer that does not wash. It uses enough water to wash one sock and that still comes out stinky.. All my clothes no matter what cycle I use including deep fill power wash or if I add my own buckets full of water to the 1.5 hour wash cycle still come out dirty, stinky, stained and caked with detergent...Hey Maytag heres a hint. You need water to wash clothes and you need agitation to get out the soil, the dirt, the sweat, the stains, the stink and your washer does none of that. In fact I could get my clothes cleaner if I out them in the bath tub and swished them around with a broom stick for 3 mins. How could you go from the loneliest man on earth to the biggest scammer on earth by producing this boondoggle... P.S. Its only me and my wife. We are retired and our clothes are not even that dirty... Its just common sense. No water no action no clean. Ill never ever ever buy anything that says Maytag on it ever ever again and you can bet your life Im telling everyone I know this story.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

Bought a Maytag top loader washer from Lowes in July 2017. Have had nothing but problems due to faulty computerized guts. Worked intermittently and took a long time to wash compared to older machine. Repairman out twice... replaced computer board and still have problems. The machine was made in Canada according to the label. Hey Canada, what is going on making junk? Too bad that we did not know beforehand what junk the Maytag brand has become. Lowes should not sell this junk to help its reputation and valued customers.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

Bought a Maytag washer MVWC415EW in 4/2015. We dont use the washer heavily but over that time span the paint on the top cover and the side where the cover comes down has bubbled up. It looks like a bad rash but only on a washer. I think the company used inferior paint which can bubble up with the heat of the hot water during the wash cycle. I called the company but they do not cover cosmetic items on the warranty. I think since this was a flaw in the paint used they should at least replace the cover portion which would be an easy fix. Maytags are not what they use be! Last Maytag lasted 17 years with no paint problems or mechanical problems.

Oven door glass shatters after 6 years of having this oven and the company refuses to cover it. According to them it is not a safety concern. It is actually designed to shatter this way. Wow, thats comforting. Should be 0 stars not 1 star.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

Maytag Washer was bought on May 2010 for $746.29 and it broke down. It was used only twice a week. It now requires repairs worth $991.36. All Maytag reps say is I am sorry, there is nothing we can do. Isnt there a lemon law for major appliances?

Dishwasher is just 2 years old. Touch panel is bad, not Maytag of old. Waiting for the corporate apology. Seems to me that this is a common problem and a case of poor engineering. Also seems like a case of the middle American getting worked over by the big corporate giant. Not happy. Will not suggest Maytag to anyone. Not looking forward to having to replace something that should have lasted significantly longer.

Bought a Maytag front load washer and dryer, it rattled and shook from day 1, they have come out 3 times in 1 month to fix that, now it wont even spin. This will be the 4th day of work I have had to miss, and all they say is, We have to send someone out to repair. Sorry. Do not purchase their products!! They dont care.

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

Maytag Dryer model # MEDC400BW. I purchased this dryer in March 2015 the fuse went out in August. It is now November and it is out again! I have been buying Maytag since I left home at 18. I am 62 now, so I have been a loyal customer because Maytag was a great product. Not anymore since Whirlpool bought them out! You have to call them to schedule a technician and then it can take anywhere from 1 week to 3 depending on when they get the parts because they have to order them, and nobody else can come out to work on it if it is still under warranty! This is so lame and just not right.

Back a couple years ago, Dec. 29, 1983, I purchased a Maytag washer, model A209, and a Maytag Dryer, model DG110. Im still using them daily. The washer has given NO problems, other than the brake has taken to squealing. This causes nothing more than a notice that the load is done, so no repair is necessary. The dryer has proven more problematic, as I have had to replace the ignitor three times, the blower fan twice, and the motor (and belt) once. I still think I have gotten my moneys worth.

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

Nice refrigerator, but cheaply made. I paid 1800 with tax for my french door Maytag and expected higher durability. It operates well but one worries about breaking drawers made of such thin plastic.

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

We purchased at Home Depot on 5/12/2012 a Maytag dishwasher model MDBH979SAM. The following November it started not working correctly. We had to fiddle with the cancel button to get it to work at all. It just kept on getting worst to where it would not function at all. We called Maytag service. They set up a service call with a local warranty service provider who ordered a control board and a week later came and installed. No charges at this point. Now, here at the end of August 2013, out of warranty, it is doing the same thing! I just called Maytag customer service in Tennessee and was told they are so sorry but would sell me a one year service contract. This I immediately refused. I told the person I was talking to that I had seen this website and was aware that hundreds were having the same issues and that I knew first hand that they were doing nothing about it! I informed this person I will be in contact with my home states Attorney General’s Office Consumer Fraud Division and would ask for any assistance from them available. This person then offered to replace the part at no charge, but I would have to pay for the service people to come and determine the problem (real hard to figure out that it is the control board again, same as everyone else) and then pay to have them come and install it after they order and receive it! The service order left by the tech when he replaced the first board showed a $74 fee that was covered by the warranty. So from this I have determined that it will end up costing me $150 for this repair. I also realize this repair may last six months to a year if I am lucky! Needless to say I refused this last offer too. I will have to wait to hear from our Attorney Generals office. How can any reputable business do this?

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Bought this Maytag Bravo washer in 2013 expecting long service life like I had with my previous machine. After 2 years spin cycle noise got progressively worse. Until now it roars loudly and keeps stopping in the spin cycle for rebalancing. Called Maytag. Experience was as described as others have reported with them and their repair service. Absolutely no help unless I spend another $310 for extended warranty to cover the $380 part (tub and bearing - 1 unit - cant get only the bearing). Paid $800 for the washer now more for the repair wanted. $1100-$1200 for a machine that will need repair again in a couple of years? Dont think so. This machine is only good for a boat anchor. Going out today to buy a replacement for $400 and it wont be a Maytag or its affiliates brand. Feel like a class action suit would be good for Maytag to wake up to.

I purchased a floor model Maytag Dishwasher from Abt electronics about a year and a half ago. 2 months ago, various light started flashing. Somehow I managed to get it going. Some blogs reported it might be a drainage problem. Others suggested pressing a certain sequence of buttons. After Each time I got it to work, it became harder the next. I bought Maytag because my old dishwasher lasted 13 years. What is interesting is that a company whose name Ive forgotten sent me bimonthly requests to purchase a warranty from them. Now they have stopped. I am a single mom of 3 with an unemployed ex. I work and support my family without any assistance. I count every penny. I cannot afford repairs nor a replacement now or any time soon. This is a travesty.My door says 10-year limited warranty and the delineates stainless steel tub and racks and chopper blade, but not the panel. I do not understand how Maytags denial of the problem and their unwillingness to correct the problem can improve their image. I will never purchase from Maytag or its associated companies ever again. What a scam! To be honest though, I have not contacted the company since it is not under warranty and all the blogs have relayed the same message: Maytag denies there is a problem.

Washing machine required service approx 3 months after purchase. Dryer heating element stopped working just after the year warranty ended. To fix dryer will cost approximately 30% of the purchase price of the machine. And all the while I am tainted by the 10 Year Warranty sticker that I never removed from the machines. Never again will I purchase a Maytag product.

Washer breaks after 2 years. I purchased a Maytag Bravos XL washer from Lowes just 2 years ago. One of the main driving factors for the purchase was the Maytag brand. The repair tech just told us the bearing was bad and we need to replace this and the drum. The service call was $100 and the repair will be over $500. I can purchase a new washer for this. I strongly recommend not buying any Maytag product. The brand used to stand for quality but not now. I dont think the Maytag repair is still the lonely tech they used to be.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

I dont know where to start. This machine (Bravo XL Top Load Washer) is ridiculous! When I finally figured out how to start it, it did not rinse or spin clothes. I cannot figure out how to get it to do that so Im stuck with a washer full of wet clothes. To add insult to injury, I cannot reach into the washer to retrieve them. I am 52 and all washers are designed by freakishly tall people with NO REGARD FOR WOMEN apparently! Poorly designed! Poorly engineered! What a piece of junk!

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

I bought a Maytag Gas Range in January 2010. In January 2012, the wiring caught fire, and now, the oven is unusable. Maytag was not very helpful in our loss of money and product.

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

I have a Maytag Clothes Washer. Lid Closed Light is flashing and agitator will not spin. Troubleshooting shows when the washer does not detect the lid is closed the agitator will not spin. I went to Maytag Canada website and chose Live Agent. There is no Live Agent! You get a Virtual Assistant that does not work; bad software. Virtual Agent shows connected. I type in the details of my issue and the Virtual Agent responds with No Input Detected. I type in the details again and the Virtual Assistant responds with Connection Closed, try refreshing. Over and over again. Tried calling the Maytag Canada 1-800 number. I have now been in the queue for more than 40 minutes. Just stupid cycling for a recording for common problems dealing with products that are not a washing machine (about a 9 minute cycle). NO CUSTOMER SERVICE. Avoid Maytag, Whirlpool and Kitchen-Aid products. Buy from another manufacturer that has live people working at the company.

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

Purchased our Maytag in October 2009. From the beginning it would make loud, popping noises occasionally but seemed to work just fine. At the time of purchase, we opted to buy the 5 year extended warranty for $125.00 (just in case). Here we are at seven months after that warranty is no longer any good and the freezer leaks all over the floor and we have to keep a towel at the bottom to soak it up.This morning I wake up to the panel being completely out and fridge is not running at all!!! We thought when we purchased our Maytag that we were buying the best of the best... not even close! We just paid for an expensive piece of junk! Who has the extra money just lying around to go buy a new fridge? Not us! This is unacceptable!!! I have read other reviews that sound pretty much exact to our experience with this refrigerator. I hope somehow they can and will be held responsible for putting this product on the market knowing full well it is an over-priced piece of junk.

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

I have owned my Maytag Neptune Washer since 1998 and this is the first time that it will not drain all the water... Doing some research before I call a repairman... Have a Great day!

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

Maytag 2000 series front load washer - f you are looking for a front load washer DO NOT buy a Maytag! I purchased a new front load washer dryer set late 2013 and have regretted to washer ever since. Continual electrical problems, door gasket needed replaced almost immediately AND the worst part is that it has ruined over $1000 worth of clothing due to it trapping cloth between the drum and door and wearing holes in them. No matter how I load the clothes or sort them it continues. I have contacted Maytag and was told I have no recourse as the warranty is over. I was very disappointed because I have had Maytag products in the past and had no problems. Please, think twice before buying this washer! It will cost much more than just the ticket price!!!

We purchased this oven (MGR5775QDS ) along with a Refrigerator/Freezer, Dishwasher and Microwave on 2007 when we remodeled our kitchen. Since then the Refrigerator had to be serviced twice, the Dishwasher had a recall for fire safety - repaired, but I still have a scorched bottom tray, and the oven after self cleaning once has warped and the racks will not hold anything with any weight without collapsing. Maytag sent me new racks about a year ago, but that didnt help. I grill most of my meals or cook on the stovetop but on the rare occasion we try and use the oven it’s a nightmare. We lost a Thanksgiving Turkey and Easter Ham and recently a lasagna and a glass pan. Every time we have one of these events I search the internet in hopes that there has been some kind of recall on this model. It’s not safe. When the 20 lb turkey came crashing down, my wife was nearly burned by the juices that splattered and the house filled up with smoke. Happy Thanksgiving from Maytag - everyone go stand outside in the cold for 1/2 an hour while we clear out the smoke in the house. Recently when the rack collapsed and hot lasagna came crashing down, the glass/pyrex tray broke and left a huge bubbly mess in the bottom of the oven. Yay Maytag, thanks again - ruined a dinner, broke a dish and since we can’t use the self clean option, spent the rest of the evening scrubbing out the oven... and eating takeout food on Valentine’s Day. Sounds like the perfect Romantic evening right? I am so sickened with this company. We purchased all Maytag appliances because of their reputation. But now they dont even stand behind their products. What a shame.

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

Never had a Maytag before I bought my house. So far the only complaint is there’s a broken piece that prevents the drawer from functioning. Otherwise, pretty good stove/range for the price. Do wish it was easier to clean without scraping anything up.

I do not have a problem with Lowes; the problem is this crummy washer. Any digital anything is only as good as its programmer, and it seems that all digital stuff suffers from the same malady. I long for the old top loader I had 30 years ago. It actually did get the clothes cleaner and they did not smell after being washed. Plus, I could customize each load just exactly the way I wanted to with the knobs and dials. This Maytag goes to Error when adding water because I have an old well which does not supply enough water fast enough for the way it was programmed. I have to fill two two-gallon buckets and carry them to the laundry room and pour them into the washer. Every time. Hot, cold, or warm, it doesnt matter. And I, too, have to pre-wash some dirtier items. The old gasoline Maytag did a better job than this one. And this is progress!!!

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

Model MBF 2258XEW3. I am very annoyed with this fridge. Never will buy a Maytag again. I went to this site to see what the problem with my fridge was and read that I am not the only one with this problem. From the beginning it never worked right. Often the food in the fridge got ice crystals in them so I had to up the temp. This made the freezer not cold enough so I had to lower the temp again. This is a constant affair. Now the bottom of the freezer is collecting an ice sheet or a water bath that has to be removed every other day so that it doesnt built up or leak out. Will have to buy a new fridge. But now I am worried that I might buy another lemon.

Very disappointed with my 2014 purchase of model MDB8959SBS3 dishwasher. In fact it is no longer in service. We used the dishwasher approximately twice a day. The wheels on the pull out racks starting falling apart in the first 6 months. Then the soap dispenser failed. It would not shut. We replaced both the wheels and the dispenser only to find ourselves with the exact same problems in a matter of months. My hubby got really good at fixing both of these items. The final straw was earlier this year as when we turned it on the motor/water pump started making a screeching sound. Never had to replace an appliance that was only four years old in my lifetime. Just very disappointed with the quality of Maytags dishwasher.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

On May 23rd 2009, I bought a Maytag Dishwasher and paid $360 for it. Within the first year, the circuit board had to be replaced, then one year later, the same thing. On October 8th 2011, it appears that the same thing needs to be done. I spoke with the customer service and they will not pay for it. Clearly, this dishwasher has a history of being unreliable and should be covered or replaced. The internet is full of complaints against Maytag for this very same model. How is it that they have not reacted or invoked a recall? I had a similar incident two years earlier with a Whirlpool dishwasher; it turns out that they are the same company. I will never buy their product again!

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

Well I have the washer and dryer. I love the dryer, it is excellent! Now on to the washer. It tries to save water so I guess people in California would love it. I have a laundry room in the basement and one up on the top floor with the Bravos in it. I only do the clothes that are not dirty but a little smelly in the Bravos. Any clothes that are dirty I do in my 20 year old machine in the basement. Do not purchase this machine if you are under 56 because you will need a step stool. Everything I wash I do on the longest cycle because the other cycles do not get all the clothes wet. Think about what I just said. The machine does not get all the clothes wet. Do not purchase this machine. I really cannot call it a washing machine, but they look real pretty in the laundry room.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

In January 2006, we bought a Neptune washer and dryer, model# MAH5500BWW, because we thought they were superior to any other at the time. In January 2012, the washer started making a very loud noise in the spin cycle. It just kept getting louder and a technician was called in check out the problem. We were told that the bearing was going out and he found a hole in the back of the tub. He said it was not cost effective to replace the bearing and the tub and suggested that we continue to use it until we could no longer tolerate the noise. We are very unhappy with the durability of this washer, with the amount of money we paid to be going out only after 6 years of service. We have been a Maytag customer for 15 years and will never buy another Maytag appliance. We are going to replace the washer and dryer to keep a matching set and it certainly will not be a Maytag.

We bought a Maytag refrigerator. Big big mistake. It bangs, makes all kinds of noises. The bottom freezer has ice that builds up once in a while, has to be unloaded and thawed out. We have had several service calls and they do not know whats wrong. Trouble started about a month out of warranty. Called Maytag and they would not do anything. WE are very disappointed in Maytag. We spent more money to get a good product and ended up with junk. We are getting rid of it and buying one that is made by a company that knows what they are doing.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

Bought brand new Maytag dishwasher. Worked great for 3 years. Then caught on fire. Couldnt contact maytag for a month because when you call your on hold for 30 minutes. Then when I do contact them they will only want to give 50%off another of their products that Ive already had catch on fire. I will never buy another one ever.

We bought a new Maytag dishwasher MDB7609 as part of the 2010 recall. Within the first twelve months the black skirt at the bottom of the door collapsed to the floor. It was in small pieces and brittle as though exposed to excess heat. The repairman fixed it free but made the point it was not covered under warranty. Next the heated dry cycle baked the water onto the dishes forming a white crusty layer. We have a water softener that works very well. We stopped using heated dry because it is too hot. Last night before bed, I was standing in the kitchen and I smelled something burning. My wife had mistakenly programmed heated dry into the cycle. Obviously this dishwasher is as much a fire hazard as the one it replaced but no recall has been issued yet.

I wrote earlier about my dishwasher needing to have an electronic board replaced again. So I called the helpful (I say that with sarcasm in my voice) 800 number. My dealer asked me to call for help with paying for the new part. After an hour and a half of being cut off and put on hold, I finally got through to a person that could take my request. The gentleman explained to me about why they would not stand behind their product which was only 3 1/2 years old, and a replacement part that lasted only 11 months. He expanded on his thought about how it was too old to fix and the part was more than 90 days old. I am out of my $1,100.00 with no help in sight. Totally upset with this company and how they will not stand behind a poorly made product!!!!

Fire Hazard - poorly designed with vent at bottom of oven, Warped Drawer and Melted cabinet surface. Nowhere in the install instructions does it say not to mount above drawers. Whirlpool tried to blame dealer. Buyer beware.

I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.

I just purchased a Maytag Washer and Dryer. I am very pleased with the cleaning ability of this washer. It has set pre-timed washing and drying times. I would like to have availability of setting the times for a load to run. Same with the dryer. The book says you can do this but I have not figured out how. I have been very pleased with their abilities to do what they are supposed to do. Cleaning and Drying.

Bravos XL IS A JUNK. I have had this Maytag washer maybe 2 years at most and it is junk. I called. Told/complained them about the noise during wash cycle and spinning. The 10 years warranty is falsely. The 10 years warranty is covered only 2 components in the entire machine ???? and does not include the labor cost of $130.00 an hour. Sadly, I have seen many negative reviews their product. I didnt check reviews before purchasing, I knew I needed a large basin and wanted the deep fill option. I always thought maytag was a good brand. Now I am in a jam. ???? If you are looking for a new washer read the Maytag reviews before considering this brand. Live and learn. ????