The way the outlet line and pump are set up, the Maytag Bravos does not remove all water from the bottom leaving about 2-3 inches. Even following the monthly cleaning and care has not stopped the inside of the tub from producing MOLD. When I contact Maytag there was nothing they could do about this problem. At this point my washer is only a few years old. I attempted to clean it myself but the drum would not break free. My options are, deal with the smell of mold and mildew, Pay Maytag $250 to come out and clean it (this would need to be done every 1-2 years) or buy a new washer. NOTE: I paid about $550 for this one. I have run a few clean cycles with bleach, but I think at this point the mold has embedded itself into the plastic tub.

The 2013 Maytag dishwasher panel broke 13 months after the purchase. After several phone calls and complaints they agreed to replace the panel at no charge. Since yesterday I have the same problem and need them to replace this washer. I am on a limited SS income and I am not in a position to purchase another washer after 3 yrs. My previous one lasted almost 15 yrs. This is totally unfair and I hope that Maytag replaces this entire machine, not just another repair. It will cost them a lot less to do that by either sending or having LOWES to replace this one. Thank you so much.Updated on 09/16/2016: Maytag is asking $300 to fix it and they will not replace it. So, by coincidence a friend of mine had the same problem and she did the following and I repeated these steps and now dishwasher is working. Turn off the switch or unplug, or turn off from the circuit box, your dishwasher. This cuts off electricity to the washer totally. Wait 30 seconds. Push the cancel button and hold on pressing it for 30 seconds (precisely, not less). Push then, the start button and hold on for 30 seconds again. Turn on the power and the cancel light will come on and let the cycle finish do not touch anything, until it is turned off and the light goes off by itself. Then, choose your selection for washing push start and see if it works. It did with mine and hers. Good luck and LADIES- YOU CAN DO IT, if this little old woman did it by herself.

I bought the product thinking Maytag - should last a long time. Sadly I was wrong. Bought the microwave from Home Depot in May, 2016 and had it installed by them. The product worked fine for the first 14 months. In fact I thought it was great. It was quiet, heated things quickly - a great product. In July, 2017 I started having problems. The product would start. I was getting a message to Close the door to start the microwave, even though it was closed. When this would happen I noticed that when the door was open, the light wouldnt come on. It would require multiple open/close until finally the light would come on (when door was open). Only then, when I closed the door would the microwave operated as it should. I lived with this inconvenience until Dec, 2017. Of course - over the holidays is when it decided to quit working entirely.I did my digging and found problems with the switches. I replaced 1 switch - still didnt work. The cost to have a repairman come out is ridiculous (Sears wants $250). My frustration was growing and my confidence in the product was waning. So time to get another microwave. I was done. Frustration and anger doesnt begin to describe my feelings. I went with another brand. It isnt installed yet, it should happen this week. In the future I will tell friends to avoid Maytag microwaves. Apparently they just dont last. I realize this isnt a top of the line microwave, I only spent $299 (plus tax, installation...) but really - shouldnt it last more than 14 months before it starts giving me problems? Very disappointed!!!

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

The Maytag Maxima XL front load steam washer is awesome. Its reliable and does an amazing job. There are so many features and settings and it makes my life easier when it comes to doing laundry. My favorite feature is the allergen setting which gets rid of allergens in my fabrics.

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

Purchased Maytag Dishwasher Model MDB7749SBW3 in April 2014 along with other Maytag appliances to go into our home in the Georgia Mountains. Purchased Maytag for 2 reasons: 1. American made 2. Reputation. Bottom line, after just 2 years the dishwasher has failed. I prewash by hand everything that goes in. First the normal cycle stopped working. Then lights on front panel would randomly turn on and dishwasher would turn on by itself, and run for hours. I suspect this could be a fire hazard. I have tried front panel resets, cycling power, etc. Nothing works... It is really sad that American products are third world. I will replace the board myself in hopes of getting another couple of years out of it. No more Maytag for me. Rest assured every time I see someone in Home Depot or Lowes, looking at Maytag appliances, I will go out of my way to warn them.

I believe the Maytag Bravo washer and dryer was manufactured so the Maytag man would have something to do once again! Buyers Beware! My $800 washer broke down 1 week after warranty costing me $400 to repair!!! Half the cost of a new one... now the dryer is making horrible noises. I fear calling for repair... or should I just buy a new different one?? My last washer and dryer lasted 30 years!!! Bravo certainly did not have all the kinks out of them before marketing them! The cost is to the consumer who trusted the name! You cannot return a 2 year old appliance! The laundromat would have been less costly than this washer and dryer! Maytag should be made to recall these defective machines or at least repair for free. Do not buy!

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

Purchased my Bravos June 2012. This is a horrible washer. It does not clean. It leaves a detergent scum line on clothing. My work clothes are visibly soiled and sometimes come out in a tangled mess. Maytag ignored a first complaint from my wife. I complained again today. Regardless what Maytag does, I will purchase another brand after research. We bought on Maytag’s reputation.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

I bought a Maytag washer November Thanksgiving of 2013. This washer started giving problems three months after; problems such as the cycle stop turn over properly, the light would say wash but its not washing. It would just stop but the light stuck on wash for long periods of time. Press the pause/start/cancel button, it would sometimes start again and stop and let out the water quickly. The clothes would be filled with water and not wash properly. This the funny part, serious funny part. I contacted Maytag on countless time. They had me on hold so long I had to hang up; a hold for hour I am talking about. One day I finally got through. They gave me a number to contact because where I am located there is no tech. I never got anyone but the machine when I called the number after countless times of trying. I decided to called back Brandsmart, because I just think its not right and fair to me to purchase a washer for so much, to had it shipped for more money. It didnt last me NO time at all and I cannot get any help. Well! Brandsmart told had to have paid export shipping, something I never was offered and since I took it out of the country, there is nothing they can do for me. I hunted for my receipt and to this day I I still have it. All was offered was warranty parts and labor for a month, thirty days. I said no because I would not think anything would go wrong in that short period of time. Nevertheless was not offered any export shipping warranty like what they are trying to ** me with. Here is my receipt number **. I grieve presently how I was just robbed of my money so openly when all I wanted was a replacement.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

I am very happy with my washer. It is easy to use and does an outstanding cleaning job. I have had it for almost 7 years and have not had any problems with it. It has many different settings so it can handle virtually any cleaning job. I am particularly happy with the spin speed which is adjustable but the high speed spin really wrings the water out so the dryer which incidentally is also a Maytag drys in a fairly short time. The washer is a front loader and doesn’t use much water.

The control board is not working on my 2 year old dishwasher. I now see this is a common problem with Maytag dishwashers. I have called to see if there is a recall on this problem and they said no. I have been told it can cost up to $500 to fix it so I guess it is a throwaway. I should have called when it was purchased as the digital buttons didnt seem right from new. What a waste of money and I will never buy Maytag or Whirlpool.

My refrigerator is several years old, and I would buy the same brand when I need a new one, although I would hopefully buy a counter depth one because my kitchen is so small, and the one I have now is kind of big for the space.

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

Maytag Centennial HE Washer - Worse machine ever. Takes over an hour for a load of clothes, never clean. Had only for 18 months now, it wont advance past wash cycle.

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

I thought it was just my machine that sounded like an airplane taking off in my laundry room. Upon reading these reviews I see there is a real problem with this machine. My parents and grandparents trusted and swore by Maytag products. Maybe then, but certainly not now. Maytag for me stands for landfill. I have had 2 Maytag certified service companies come to repair my washer that is only 6 years old and its the same part both times which I am told by these service providers has been a problem and Maytag knows about it. But when I call Maytag all I get is some sound bite advising me there has been no recall and since I have an extended warranty I will have to take it up with them since that is who my contract is with. Of course they are only obligated to make a repair and cannot replace a defective unit. Of course not.Far be it for Maytag to step up and really stand behind the promises they are making all over our television channels with the new Maytag man. The top of the washer is also all rusted out around the soap, bleach, and softener openings. It is a poorly made machine with known issues by a manufacturer that I will never buy from again. Its a sad day that manufacturers are not held accountable for inferior products and even sadder that this Maytag manufacturer boasts its made in the USA for this machine. So is it back to China we go??? If you want America back you better support your product to your buyers.

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

Bought Maytag dishwasher model number MDB894995BB3 serial # F41103073. About 2 months out of warranty the control panel went bad. Contacted Maytag. After quite some time they agreed to pay for parts. After some more conversation they also agreed to pay service and labor. This was on the first day of August and Maytag scheduled a repairman for the sixth of August. When he arrived spent five minutes and said he had to order parts. The control panel I had already told them was bad. Now here I sit waiting for part to arrive. No more Maytag or Whirlpool for me.

Bought this Maytag Bravo washer in 2013 expecting long service life like I had with my previous machine. After 2 years spin cycle noise got progressively worse. Until now it roars loudly and keeps stopping in the spin cycle for rebalancing. Called Maytag. Experience was as described as others have reported with them and their repair service. Absolutely no help unless I spend another $310 for extended warranty to cover the $380 part (tub and bearing - 1 unit - cant get only the bearing). Paid $800 for the washer now more for the repair wanted. $1100-$1200 for a machine that will need repair again in a couple of years? Dont think so. This machine is only good for a boat anchor. Going out today to buy a replacement for $400 and it wont be a Maytag or its affiliates brand. Feel like a class action suit would be good for Maytag to wake up to.

Maytag Bravos XL - I purchased my maytag washer & gas dryer on 5/12/12. In Dec 2012 the heating element went out. I had to wait a week for a repairman to come out on Dec. 20 to fix it. Now for the second time on Dec. 30th, 2014 the heating element has gone out. I called for a repairman to come out. I have to wait until Jan. 12th 2015 for service. I have 8 people in my home including 3 grandchildren. This length of waiting is ridiculous and very inconvenient.

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

My built in electric double wall oven, Model MEW6630DDB, convection on the top, has been the most frustrating appliance I have ever owned. It has never kept an even temperature. It has been repaired several times and still does not keep an even temperature. It takes 14 hours to cook a 20 lb. turkey and baking cookies are not even an option. I have complained to Maytag and have paid for repair services. Their solution buy an extended warranty which is absolutely insane because they havent been able to repair it since it was new over four years ago.

I have owned several dishwashers thru the years and my favorite is Maytag. Maytag is quiet, barely hear it running which is rare for a dishwasher, dependable and plenty of space for dishes, pot and pans etc. I wouldnt have any other but Maytag. Also has several options for dishwashing which is a big plus. Love Maytag!!!

I cannot use my Maytag gas range and oven appliance until I can purchase part #W10213446, which your factory website shows as back-ordered until 2020. This means that I cant cook a meal or have the family and friends Ive invited come to my home for Christmas dinner. I need your help to provide better customer service than Ive received to date through working with the Maytag customer service call center, and the service Maytag parts distributors Reliable Parts and WC May company have received from working through your factory website.Ive owned Whirlpool appliances since I built my home in 1989. When I remodeled my kitchen in August 2010 I chose a Maytag range, fridge, dishwasher and microwave as Id had a good experience with your products for 21 years. Youve built a great reputation for quality products and service, and I hope that you will continue to deliver on the commitment promised in your brand by resolving my problem quickly. A burner control on my three-year-old gas range and oven (model #MGR6775; serial #D00934496) recently stopped working (a Maytag design defect - several screws were too weak to hold the cooktop at the correct level) and your customer service call center referred me to A&E Factory Service for the repair. A&E service staff have been to my home twice and are unable to fix my stove leaving me without a stove for the past two weeks and foreseeable future - as the necessary part, #W10213446, is shown as back-ordered with no estimated time of arrival. The WC May company let me know that your website shows an ETA of 2020 for this part on your factory parts website.When the service repairman informed me that the part was indefinitely back-ordered today, I called the Maytag customer service center asking them to locate and expedite delivery of the part. The line staff and her supervisor let me know that they would not provide that service, as I do not have a pre-existing extended warranty contract for the range. I am willing to pay for expediting the part, but they wont give me that option. So I called the parts retailers covering the western U.S. myself to learn that Whirlpools supply chain is so flawed that it cannot provide a part for a three-year-old range.Whirlpools core principles espoused on your website say that founders Lou, Emory and Fred Upton continually improved their washer; they cared about their community, their employees and their customers. They believed that there is no right way to do a wrong thing. It also states that what truly distinguishes Whirlpool Corporation is our commitment to building strong brands and a loyal consumer base. Were focused on maximizing the benefits of our worldwide network of resources, which is unmatched in the industry.I believe that leaving me for up to two months without a range, so that I cant cook meals for myself every day, and for my family during the Christmas holidays is not living up to your brand promise. Please let me know as soon as possible how you will solve this problem.

I purchased a Maytag front loader washer less than a year ago. Based on their deceptive advertising, Maytags rarely need service (model MHWE201YW00). There was a loud banging within 11 months. I called service for the additional warranty I purchased. The service man told me this machine is shot. The bearing completely broke and the drum was loose. They ordered 3 huge boxes, 3-1/2 feet cubes delivered to my house. I had to drag them into my garage where they have been sitting for two weeks. I am now 4 weeks without a washer with 4 kids. Ive called Corporate Headquarters and have spoken to their Corporate Board Gwenn and Jackyln who seem to think they can diagnose the problem. I told them the machine smelled like it was burning and the last load was dripping wet and the clothes smelled burnt. This is a stackable in my kids bedroom and I told them I was concerned about an electrical fire. Ive already missed one day of work for this. I am now being told Jan. 11, 2013 is when it can be serviced. That would be 2 months without a machine. They are willing to endanger my children with wet wires and an electrical fire. Mr. Fettig is impossible to get in touch with and this customer service center apparently has no supervisors. What they say, goes. A class action should be started against Mr. Fettig and his team of crooks who are putting crap out into the market place, falsely advertising it and then not backing up when their product breaks less than a year and becomes a possible hazard in someones home. Ive sent to his home address a UPS letter to Mr. Fettig, letting him know if a fire starts in my home due to water on the wet wires (water that got behind the drum because of the faulty bearing), water that was leaking from the bottom of the washer that I hold him and his company personally responsible. They have been alerted to the problem numerous times and ignore it. I spoke to their Safety department and I asked what to do if I smell a burning smell when the machine was running. They told me to immediately shut it off and unplug. Yet Whirlpool is trying to put a Band-aid on a machine that has already been infected with water damage to the wires. This has been such a frustrating, stressful experience. Even 5 weeks from now, when my replacement parts are put in, I will worry each time the machine is run if there will be a spark from the damaged wire. Something must be done legally to stop these crooks from doing to this and getting away with it. All they care about is their profit margin. The Whirlpool creed to their customers is a bunch of bull! Mr. Fettig vacations at his home on Dolphine Island, Alabama while hardworking people are scrambling around trying to figure out what happened to their new appliance that promised to work but is broken in less than a year. He vacations at his home in Florida while the hard-earned money you spent on his product is a waste.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

I have now owned my highly efficient and low-cost to operate washing machine for 6 years. It is a top loader and uses HC detergents.This means the washer needs minimal soap to clean the clothes. I especially appreciate the different types of loads such as deep cleaning or regular cleaning. The washer has sensors that evaluate the size of the load and thus only utilize the amount of water necessary. I really like the quietness and being able to get the very best wash because the washer does exactly what it needs to do. It has more than been the appliance that I had hoped for. Love it! It maintains itself.

This machine doesnt wash your clothes. It leaves them dry & the agitator sucks too. I am so annoyed. I just bought them & had them delivered 7/27/15. It has only been a few days & NOT satisfied. Overpriced over $800 for it & its crap! Same with the Bravo dryer, it takes forever to dry. I wish I still had my old washer & dryer (had them for 7 years, NO problems). Very unsatisfied. DONT buy these, they are total CRAP!

Bravo XL Washer & Dryer - I have owned this set for just over 90 days and have called Maytag several times just to get insulted. The customer service representative is not helpful at all, and tells me that I am not using HE detergent or that I am using too much HE detergent. Furthermore, they tell me that if a service technician comes to my home and nothing is wrong that I will get charged. So much for the extended warranty and what is wrote on the Maytag site. I explain each time that I am using name brand HE detergent and the recommended amount. The soap dispenser in the machine provides a fill line that I fill to. I have even tried using less detergent as recommended by the appliance store that I purchased the machine from, and still the washer does not clean my laundry and leaves residue on everything. I have even tried using the extra rinse, and extra heavy soil setting which does not make a difference at all.The other concern is that the clean washer feature light flashes weekly. I have purchased the cleaning tabs recommended to clean the machine, and run this clean cycle every time the light comes on. The dryer does not work all that well either and shuts off before the laundry is dry. Sometimes the dryer will show an error of airflow restriction or low airflow. This is confusing because the dryer vent and hose are clean, and the lint filter is also clean. This is so disappointing because I thought Maytag had great products. However, as I read other reviews about these machines and the customer service representatives it seems that there is a systemic problem with the machines and the customer service representatives that needs to be addressed by the leadership at Maytag.

The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

The dishwasher stopped working. The lights on left side of control panel arent working; so, machine wont start. Then machine was purchased in January 2010 for $525 and not including installation. Kim says it will cost $129 for their repairman to come look at it. I wished I had read the list of complaints on your site first.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

I purchased a Neptune front-load washer in November 2005. Now that its out of warranty, theres nothing that Whirlpool can do for me. The front panel of the washer that surrounds the door has been rattling for a few weeks, so my husband took it off and found a crack on the top right section of the panel where its bolted to the frame. There is a rust bubble where the crack started. We couldnt see any of this until he took it apart. The cost of a new front panel is $185 and the response from Whirlpool? They are “very sorry” that this has happened, but there is nothing that they can do. Oh, really? Well, I come from a long line of Maytag owners and there is something I can do: spread the word about the disgusting piece of junk I paid $1,100 for! This washer wasnt even made here - it was made in Korea and its not worth $100! Note to Whirlpool: your customer service sucks!

MHW7100DW Maytag Washer Steam & YMED7100DW Maytag Dryer Steam. Both of them are easy to use. They hold lots of clothing as well as bedding and many different settings. They both do an excellent job. Brand and excellent reputation. Had my last Maytag washer & dryer over 25-years and had no problems with either. Thats why I bought Maytag again. Repairs are very costly when you have to pay technicians. Dont like poor quality construction or enamel chipping when you place items on them. Very easy to clean both of them. Practically no lint dust emitted into the room from the dryer. Had no problems with my previous washer & dryer. Thats why I purchased a full size Maytag washer and dryer again.

I bought a Maytag washer and dryer in Cookeville TN. In 2018. After a year it quit. The service man from the authorized dealer in Cookeville could not repair it. After numerous calls Maytag sent a service man to repair it, this took about three weeks. This washer is a Maytag industrial, it has a 5 year parts and labor warranty, and 10 years on the motors. Now it is out again, after calling Maytag, and holding on the line for an hour, finally I had to chat with someone, and they set up an appointment for about 3 days. So service company call now and says it will be another week before they can sent someone to look at it, and another week to get the parts. They also questioned my warranty. I gave high dollar for this washer, what’s happened to Maytag?

I bought a Maytag electric stove steam lift oven 2 years ago, I regret it. I baked a pie, and used the steam cleaning, it didn’t clean, my oven is still dirty. The top of the stove is not easy to clean and scratches very easily. It’s not my first stove, different brand, and I never had problem like I have now. I should have stayed with the brand I had before. My other regret, I should have read the reviews.

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

In May 2007, I bought a matching Maytag Neptune washer Model MAH5500 and dryer. I also bought the 3-year extended warranty. Approximately 4 years later, actually 1 month after the warranty had expired, the washer started to get very loud and sounded like a jet engine taking off. I called Brennen Repair Service in Midland, Michigan. The repair man came out and said he did not even have to look at the washer. He knew what was wrong. The bearings were going in the machine. He said I could fix it for approximately $600 or just run it till it quits. I was furious. I called Maytag and explained my issue and was told that there was not a recall and they could do nothing to help me. They even told me that they had not had any complaints of this nature regarding this model. I told them they were full of it. I know of at least 4 people in my family and workplace that have had to replace the Maytag front loader piece of ** washing machine. I think Maytag should stick behind their product with all the complaints out there. I would like to shove my washer through their front window. I previously owned a Maytag washer for 25 years and had not one issue. It ran perfectly. I will never buy another Maytag product nor will anyone in my family. Maytag, you suck. Your service and reputation is appalling.

I have the Maytag Gemini Double oven 5 burner stove. It is great! I use the smaller oven more than the bigger oven. Holidays and cooking are a lot nicer with my range oven. The turkey can be cooking in the lower oven while pies are baking in the smaller upper oven. I have had my range for a while now but I have not once had a problem with it.

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

I absolutely love this Maytag Bravos XL washing machine... I bought this machine before doing any research because of a sale and then after reading multitudes of reviews... positive and negative... I thought I had made a mistake. The absolutely most important thing with this machine is to load it properly and select the proper wash cycles. You must stack your clothes around the outside of the drum leaving the center open. You must use HE detergent. This is a Commercial grade washer and is meant to be loaded. The twisting and wringing of clothes is because of the high speed nature of the spin cycle (commercial). If you have never been to a public laundromat then you should try it and see what those machines do to your clothes. I too was apprehensive about the water levels at first... So I stood there for an entire cycle multiple time and on diff settings.The machine is constantly adding water as needed and each time after about 10 min... no matter the size load I put in. The clothes eventually were covered by water. Have had no issues with clothes that come out dry in spots. I suspect this is due to improper loading. Again my info on using this machine... loading techniques etc.. all came from positive reviewers stressing the importance of these key factors. This machine was not designed or intended for light or delicate use. So if you do a lot of those type loads perhaps this machine is not for you. As for the loudness and banging I have read about I have not experienced that. I have read reviews that the problem in some case ended up being metal or plastic drip pans used under the machine. Mine sits on concrete. Anyway hope this helps someone out.

I purchased a Maytag dishwasher at Home Depot in Roanoke, TX on 07-14-2011. Model Number: MDB7749AWB2Serial Number: F12604431Unfortunately, Ive just been obliged to open my third service call on this new dishwasher. The first service call was made in August 2012, just outside of the first year warranty period to repair a wire which had come loose in the control panel, making the dishwasher inoperable. The second service call (May 2013) was to replace the front panel housing and touch pad which had broken off at the screw-mounts holding it on to the door. As the handle to open the dishwasher is part of the front panel (which must be pulled out pretty hard to open as it does not have a latching mechanism) screws set into unreinforced, thin, plastic posts holding the panel to the door seems like a serious design flaw.The third service call which I placed last week (August 2013) is to address the fact that the dishwasher has become completely inoperable with no lights on the front panel and is completely unresponsive. To say the least my experience with this product (and by extension the Maytag brand) has been a serious disappointment. I guess the reason I no longer see those TV commercials with the lonely Maytag repairman is because these days hes actually really busy fixing broken down ** Maytags. I will never, ever buy any Maytag or Maytag-family brand appliance ever again.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

Bought the pair of Maytags on sale at Lowes 6 years ago. They are commercial grade and wash everything. Have had no issues - works every time. It took a while to get used to not have an agitator but now it seems natural. Would buy again.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

So we purchased a whole package in sept 2014 for our newly constructed home. In Nov we received the CO and thats when everything was finally professionally installed. After its first wash the dishwasher broke and there was a flood in the house and soaked 20% of the newly installed high quality cabinets. We cleaned up everything and called Maytag to have someone inspect it to see what needs to be fixed. The gentleman came about a week or two later and said that the machine isnt worth fixing and to try to get Maytag to replace the whole machine, but he still listed all the parts that were needed to fix it. We tried calling Maytag and said what the repairman said but they said he must fix it and they will not provide a new one. So we wait for the parts and no one calls us. We follow up with Maytag and they say theyve ordered the wrong parts so it will take longer. We try calling the repair man and he doesnt call us back.Then call Maytag again and get them to call the repairman to see why he doesnt answer us. They told him to call us twice and every time he tells Maytag that hes called us and we dont pick up. So we tell Maytag hes lying, the repairman hasnt called us for weeks and Maytag doesnt give a **. And seems like this repairman is freaking lazy and doesnt want to work, even if hes paid for it. You know whats happening now? Chargeback! Thats right Maytag, screw you. When I do another house I will never buy Maytag again! Horrible service and a very defective product. I thought we were paying for quality!! They lost a customer that is faithful and doesnt mind paying extra. Hope everyone can take this into consideration before buying. I wish I wouldve seen these comments before...

Bought this machine with the intention of having at LEAST 10 problem free years with it. Its a Maytag after all. Not an unreasonable expectation. Within the first 2 years, the machine sounded like the bearings were going out (heavy, grinding noises when it shifted gears). Repairman came, replaced the entire drum (only way to get to the gears, I guess). Didnt fix a thing. Then the rinse and spin cycle on ANY wash cycle randomly quits. Just stops. Full load of wet, soapy clothes, sitting in the tub while an LD error code quietly flashes.Its not uncommon for it to take two full days of screwing around with this machine to get one load of clothes done. Have to UNPLUG the machine, let it sit for about an hour, and try again. It is the biggest waste of money ever and I will NEVER buy another Maytag nothing. Contacted Maytag and they recommended I call a repairman...REALLY? REALLY? Gee, I wish I had thought of that. Repair guy has been to my house so damn many times for this machine, we are now friends on Facebook. Dont waste your money on this machine.

Absolutely the worst experience ever. The repair people that were sent to address the problem were great but the Maytag people did not care. I bought a new electric convection oven, the convection never worked. The repair people came out several times and checked and adjusted to try to fix the issues but the oven is totally inconsistent. Even the repair people thought I should have gotten a better response from Maytag! Maytag just said that I had a repair but not replace warranty - of course the warranty period is over now. I had trouble from the beginning, I would never buy another Maytag product. I thought that a company that supposedly has a great reputation would care more about their customer.

We are on our 2nd Maytag refrigerator in 6 years and both units have failed. Maytag will not stand behind their product and the service company declined to come out to look at the unit because we were upset and contacting the BBB. So we have spent thousands on 2 refrigerator units that have lasted 2.5 to 3 years a piece. If I could give no stars I would and I would advise to look at other companies and models.

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

I, too, have had a lousy experience with this washer – it does not correctly sense the amount of clothing in the load, and often fails to get everything wet. Once the cycle starts, it does not necessarily pull everything into the water. You must ball each item up around the center or have sleeves and legs of clothing end up very twisted. Clothing is often very wrinkled and I do not feel that enough water is used to achieve clean clothes. I did get a good response from Maytag, who sent a repairman free of charge after the one year warranty period. He was very gruff and condescending – implying that I am buying the wrong kind of clothing. He reset the washer which improved the water levels, but now it is back to its old tricks. Hate, hate, hate this washer. Now it is failing to start unless lid is slammed shut! May get a new one in a black Friday deal, but have to figure out how to ditch this one while retaining my integrity/honesty to buyer.

I own a Maytag dishwasher - it is a few years old now. I first filed a complaint in 2011. We have had it repaired several times - the control panel keeps breaking. Why is it that my grandmothers old dishwasher worked for 30-40 years and now you are lucky if you can get an appliance that works for a year without breaking? This planned obsolescence is ridiculous. Do not buy Maytag products - hit them where it hurts - in the wallet. They used to build quality products, but not anymore. I contacted the law firm in California that another person had listed as they have started a class action lawsuit. Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 - if you are having atrocious problems with your Maytag dishwasher (they mentioned Fridgidaire, too) - because of the control panel, please call. The company wont fix the issue unless they are forced to.

Purchased a Maytag microwave/range hood in 2005. So yes, it is almost 10 years old but should the handle break off in ones hand? I would say poor material is the culprit. No use contacting the company by the looks of it... they dont stand by their product. Warranty says 10 years but broken handle would likely be cosmetic...

Maytag model mfd2561hes French door stainless steel purchased in June 2005 has been the worst appliance purchase ever. After 1 year warranty expired, icemaker and water dispenser stopped working. Was told by repairman to thaw the tube for water dispensing with a hair dryer. Are you kidding me? Why should I have to pull a huge refrigerator out from wall and put the hair dryer to it to thaw out the water line when I need water? What is the convenience to that? Cant buy fresh vegetables as it will freeze before I can use it. This is the worst appliance ever. Dont buy Maytag products. Maytag doesnt back products like the old days when they would last 20 + years. Cant last even a year anymore. Sad!

My husband and I bought a Maytag dishwasher, Stove and Fridge. We were very reluctant because at our prior home we had Maytag appliances and they kept going out. Against our better judgement when we moved into our new home we decided to go with Maytag once again. First the dishwasher front panel stopped working. We had it replaced and it cost over 250.00 with replacement part and labor. Not a week later went by when our Fridge went out, that cost us another 300.00 plus to fix. Keep in mind we had only had these appliances for about 14 months. Less than a year of replacing the dishwasher panel it has gone out again. This is very frustrating and expensive. I dont usually write comments, but felt the public needed to know that Maytag has poorly made appliances. I recommend you spend the extra couple of hundred bucks and buy the better brands and warranties. Thank you.

The bearings and motor went out in less than 3 years. The warranty good - the dealer I purchased from Siano Appliance gave me credit to purchase another Maytag washer - which I had to purchase an additional warranty for $320. The new Maytag is less than 5 months old - the motor has been replaced and waiting on a tech now to fix it. It would not come on. SO in warranties I have paid over $640 and am still having issues with the new washer. The first time I purchased a warranty for 10 year - when the machine was replaced I had to purchase another warranty for that machine - now if I have to replaced this one that will be an additional $320. IS this legal?

WOW, I cant believe a group of educated professionals made, tested, and approved such a washing machine. What a piece of crap. I could put my clothes in a bathtub and let the kids jump up and down on them and they would come out cleaner. I would love to have a heart to heart talk with the engineers who designed this, to ask, What were you thinking. What a waste of money, and a once good company, that will soon be going out of business.

Thank all of you for saving me. I was about to buy a Maytag with bottom freezer from Home Depot. No wonder they are marked down an additional 20% off their sale price.

We purchased this oven (MGR5775QDS ) along with a Refrigerator/Freezer, Dishwasher and Microwave on 2007 when we remodeled our kitchen. Since then the Refrigerator had to be serviced twice, the Dishwasher had a recall for fire safety - repaired, but I still have a scorched bottom tray, and the oven after self cleaning once has warped and the racks will not hold anything with any weight without collapsing. Maytag sent me new racks about a year ago, but that didnt help. I grill most of my meals or cook on the stovetop but on the rare occasion we try and use the oven it’s a nightmare. We lost a Thanksgiving Turkey and Easter Ham and recently a lasagna and a glass pan. Every time we have one of these events I search the internet in hopes that there has been some kind of recall on this model. It’s not safe. When the 20 lb turkey came crashing down, my wife was nearly burned by the juices that splattered and the house filled up with smoke. Happy Thanksgiving from Maytag - everyone go stand outside in the cold for 1/2 an hour while we clear out the smoke in the house. Recently when the rack collapsed and hot lasagna came crashing down, the glass/pyrex tray broke and left a huge bubbly mess in the bottom of the oven. Yay Maytag, thanks again - ruined a dinner, broke a dish and since we can’t use the self clean option, spent the rest of the evening scrubbing out the oven... and eating takeout food on Valentine’s Day. Sounds like the perfect Romantic evening right? I am so sickened with this company. We purchased all Maytag appliances because of their reputation. But now they dont even stand behind their products. What a shame.

So disappointed in Maytag - I have a 2013 Bravos washing machine that if I had it repaired again (less than a year after I had it repaired the first time and just over two years since we brought it home) the cost is going to two times the purchase price. And because it is just out of warranty Maytag is doing nothing about it, even though they know there is a flaw in their design.

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

Maytag French door Bottom Mount Model # MFT2976AEW02 - Purchased this model refrigerator in late 2013. Had minor problems with ice maker for last 6 months, not have freezer problems, as the bottom freezer is not keeping food frozen. Called repairman today. He ran 64 checks on refrigerator, said to keep eye on problem and he will re check in 24 hours. Called private company, Maytag in Latrobe. They referred us to the Maytag repairman. We will keep you posted. We moved all of our frozen food to a downstairs older freezer for safekeeping. Keep checking, we will update.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

I am so fed up with my Bravos XL washing machine, that I felt compelled to vent and see if others have the same issue. The first two reviews I read complain of the same thing as I am finding. Some kind of scummy residue on my dark clothes, need to rinse, sometimes soak again to get the residue off. Have tried many different detergents. The guy at the store said try cold water! Yeah right. I use half the amount recommended. We have two boys who play baseball. The seller said this would be a great machine. Id almost consider trying to sell it on Craigslist and buy a good used one with an agitator. Spent a lot of money on a fancy looking machine. Definitely overpriced and overrated. Do not buy this machine!

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

We had Maytag brand washer and dryers in the past. They worked for years and I was able to repair or replace switches and some parts on my own. The new Bravos XL is a very inferior machine, nothing but problems. The clothes have to be washed two or more times to make them clean. There is no agitator, so your clothes have only other clothes to scrub up against, and the spin cycle is just thumping and banging and thrashing around until you’re able to get in and rescue it from itself. Our older machines had tiny steel shot in the rim of the machine to keep it balanced. Don’t buy this machine ever!!!

We went to Home Depot and bought a Maytag front load dishwasher and dryer and microwave 3-1/2 years ago. The washer and dryer were put in right away. The dishwasher and microwave stayed in their box for another year due to us remodelling the house room by room and the kitchen wasn’t done for a year. We put the appliances in and the dishwasher panel went out in October 2011. The washer in April 2012 started having a failure 8 when it gets to the last spin and rinse in which takes a lot of shuffling clothes to get it to finish its cycle. Then last night, May 14th, 2012, the microwave caught fire and all I was doing was brew tea in a glass Pyrex measuring cup not to mention the fan didnt work from day one. The whole house was full of smoke and it melted the plastic. So the most I got out of 3 of these products is 3 years at the most. This is very sad that we spent this much money and it lasted less than 5 years. I am writing this to warn consumers not to buy Maytag appliances. They should last longer than 3 years and are not cheap to buy. This makes me very angry and I hope someone takes this seriously and work on the problems before someone burns up due to these appliances catching fire. Our dishwasher had a recall shortly after we installed it due to the element catching fire and we had your repair man replace it.

25 months ago, I bought a brand new Maytag stainless steel microwave. We had upgraded all of our appliances except the microwave when we moved in our home. Our first purchase was the Maytag refrigerator. Should have learned my lesson from that because after less than a year, the freezer on the bottom went out twice! We bought this new microwave to replace an old one that didnt match the other appliances and was worn out. Two months ago, the code SE started appearing and then would go away after a few minutes. Now it doesnt go away and you cant use the microwave. I finally called a repair person since its out of warranty and was told that it would cost over $300 to fix it. Really! Im so angry because now I have to take money. I dont have to replace a microwave that should have another few years of use. Nothing at all reliable about a Maytag. I doubt Ill buy anything else they make.

We purchased the Maytag dishwasher model # MDB4949SDZ almost one year ago. Since the beginning there has been a smell to our drinking glasses when we put drink in them...smells like boiled eggs. We have always used Cascade dishwasher pods, but suddenly our dishes were being left with a gritty feeling film on them and I had to run them under water to rinse them after taking them out of the dishwasher. This model showed on Lowes website that it has a food grinder, but it cannot even get rid of a single kernel of corn that might get left on a plate. After a load is completely washed and you open the door, there is a strong smell of detergent. If you run an EMPTY dishwasher with NO soap it creates an abundance of suds like there is still soap all in the tub!!The repairman came out and called Maytag and they ran a diagnostic check on it and it said everything was okay. He said to run a cup of white vinegar through it and I did. It didnt help. Still lots of suds being produced when I run a cycle with NO dishes and NO soap!!! He said the food grinder doesnt actually grind or dispose of small particles of food, just grease!! What?!!!! We had to PAY $92 for the service call even though it is still under warranty just because the repairman and the Maytag guy on the phone couldnt figure out why this dishwasher is a hunk of junk!!!! Also, the top rack has clips on the side to lower and raise the rack. The outer sides of the top rack will only hold smaller glasses because these clips get in the way. I hate this dishwasher so much!!! My 18 year old Kenmore ran like a charm until Hurricane Harvey flooded our house. I will never buy a Maytag appliance again!!!

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

I have a Maytag side by side. In the first year, the ice maker failed and I had to replace it (in warranty/no charge). In the fifth year, the compressor failed (no warranty) and it hasnt been replaced. Since then, I have been looking at reviews and warranties of new refrigerators. The warranties (unless you want to pay $3,000+) are all one year limited. The reviews are scathing and it doesnt matter what brand. My question is, why dont you/we all get together and file a class action suit and demand millions in damages? Complaining wont get you anywhere with these people; however, hitting them in the pocket book will make them pay attention, especially if the penalty is severe enough.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

I purchased a Maytag MDB7749AWW dishwasher in March of 2012. The electronic control on this unit failed in June of 2013 (3 months out of warranty). I have been trying to get a replacement part for over a month; the part is on backorder and unavailable. Whirlpool is unable to tell me when the part will be available. So, I have had no dishwasher for over a month and have no idea when, or if it will be repairable. Additionally this part is $150.00 and another $75.00 to have it changed. So it is going to cost me $225.00 to repair a 15 month old dishwasher that I paid $450.00 for. I have received ZERO support from Whirlpool. They told me today, 7-31-13, that the part is still unavailable and they will notify me in 3-6 business days as to if they can find a part. After seeing all the issues other people have had with this part, Whirlpools total lack of concern or support for the consumer and the cost issue it makes no sense to repair this unit only to see it fail again in a year or so. Basically I have a $450.00 boat anchor. The retailer purchased it from feels bad and is offering me another manufactures machine at a reduced price. Maytag has refused to do anything for me. I will never buy another Whirlpool / Maytag item again and I do intend to add my name to the pending class action suit.

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

Maytag Dishwasher Model MDB 7749SAM0 - Bought this dishwasher from Lowes in 2012 for my daughter and son-in-laws new home. Thought I was making a good choice with Maytag. Wrong. Same control board problem that everyone else is having. Wiring ribbon is corroded and shorted. Why is this not a re-call? I will call Maytag and Lowes and complain, but likely will get no justice. Sounds like I should just bring this machine to the dump and take my losses.

My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.

Does not clean laundry, leaves dry untouched spots, all my clothes look unwashed & the rinse is terrible, leaves dirt on clothes due to little water in cycle. Im a senior on fixed income. I cant buy another machine.. I called Maytag within a couple of weeks of using washer. They told me We have No guarantee for Customer Satisfaction. This is a complete scam on their part. If I could of afforded a Lawyer I would of taken them to court. They knew what they were selling & somehow got away with it. Give the people what they pay for, not the Bravos piece of Junk. Can only wash on 1 cycle to get wet wash. But paid for other useless cycles. Who made this machine & who allowed it to pass to the unfortunate Consumers. If anyone can help getting Payback from Maytag, Please let us know... Better business Bureau should get after them.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

I purchased my Maytag Bravos XL washing machine in July 2016. In August 2016 it broke for the first time. I was just passed my 30 day moneyback guarantee, so Sears would not take the washer back. I have had more than 10 service calls on this washer in one year. I live in a rural area, so Maytag told me I was in a non-serviceable area and would have to wait WEEKS until they found a repair person willing to come to me. I only live 40 miles from Richmond VA, where I purchased the washing machine, so imagine my shock when they told me they couldnt fix it because of my location! Ive had countless people in and out of my house, and it still does not work right. You can only do very small loads, so the perk of having an XL machine is none. But even at that, it does not properly clean anything, tangles clothes, and will leave even the cleanest items looking terrible when they come out.Ive had a new circuit board, new transmission, new bearings and gears, new balancing rods, and still, Im left with a machine that does not wash and makes terrible grinding noises. I bought the washer and matching dryer as a set, and even the dryer had to get a new circuit board put in it in the 1st 60 days! After thousands of dollars in repairs on a $1000 washer, Maytag will not admit I have a defective machine and replace it! I just ran a load of laundry and have to call Maytag yet again, because the grinding noise gets louder with every run. Do not waste your money!I would give anything to have the 29 year old set I gave away when I bought this garbage back! I have literally been on the phone with Maytag in tears because it doesnt work properly, Ive had to throw away items that would not come clean because there is not a laundromat available in the town I live in. All I want is to be able to keep my family in clean clothing and linens, doesnt seem like too much to ask.

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.