I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

Not yet two years old, my Maytag Bravos dryer stopped working. When I called a technician to see what the problem was, he told me that the circuit board was burned out and it would be $500.00 to replace. I then called Maytag to find out if there was a problem with this machine and was told no. This apparently is a lie as there were numerous complaints when I checked the internet. I have five Maytag appliances and at this point, only one has not caused a problem. Maytag is not the company of the past when if you had a Maytag, you had the best. The repairman no longer sits around with nothing to do.

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

Maytag junk MFW2055FRZ00. We had to replace our reliable 15 year old Frigidaire side by side fridge when it failed due to a compressor failure. We should have pressed the service company to replace it or found someone who would. We were limited in replacement units because of built in cabinets, thus a smaller French door (so we have to open two doors rather than one) Maytag. Perhaps our 30 year old Maytag washer and dryer made us believe Maytag still offers high quality products. We were wrong. Everything about the unit is poorly designed, cheap and flimsy. The freezer drawer pulls out unevenly and the ice maker is primitive. Above all no matter what appliance you choose be sure there exist factory authorized servicers in your area otherwise warranty issues are a problem.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

On December 22, 2013 I purchased a Maytag front loading washer Model # MHWEE201YW00 from The Home Depot. On July 28 the bearing failed and greased my clothes and rendered the washer unusable. On August 1st I contacted the Maytag Customer Service Line; the wait for contact was approximately 20 minutes, not a very good answer time and unfortunately the best I would receive during this process. Despite the wait, I received good response and had a service call set up for Wednesday August 6th.On Wednesday August 6th, a service technician from Quaker City Appliances took a look at our washer and determined that the bearings had failed and that the entire drum assembly would need to be replaced. He stated that anytime the bearings fail this soon, it typically means that the bearings weren’t pressed properly or the drum wasn’t tightened enough and that he would order the parts as soon as he got back to the office.On Friday August 8th, a representative from Quaker City Appliances called and notified us that the part was no longer available and instructed my wife to call Whirlpool Customer Service and give them this number **, to coordinate a replacement washer. I called later that afternoon and spent over an hour waiting and was transferred between departments. The first representative was very cordial and professional; the second who I believe was from the Tech-line was anything but. In my career I have held responsibility for customer service and while there are many golden rules, one of the most important was never to tell the customer “I can’t”, well Cheyenne (I believe that was her name) couldn’t help me with anything and clearly told me so. She explained that my problem was referred to the Trade Partners and I needed to call back to Quaker City Appliances on Monday.On Monday August 11th, I called Quaker City Appliances, who promptly informed me that the matter was turned over to Whirlpool and I need to contact them as there was nothing else that could be done. Later that day I called back to customer service, again waiting between two representatives at least an hour. I was informed that my matter was with the Trade Partners and that I will need to wait one to two days for a phone call. A phone call that never came…..Yesterday August 14th, I contacted Whirlpool customer service, again waiting over twenty-five minutes for the first contact, and then was eventually handed over to the tech line and another wait. Eventually, I spoke to a very pleasant representative who gave me the Trade Partner number and transferred me, unfortunately I was disconnected. I called back and found out that the office closed at 5:00. Today I called the Trade Partner line (1-800-874-4698) at about 3:30 and after 40 minutes I have given up and decided to write this letter. All I want is a functioning washing machine.

The washer buzzes. Period. I called Lowes...they said to unplug it then plug it back in so it will reset the computer. I did twice...Nothing. A light comes on for the sensor...Then nothing. I didnt see all the bad reviews for this machine. I had my other Maytag for 24 years and the tub was going bad. This scares me. I will be calling Lowes later. They are selling defective machines and they know it.

MVWC565FWO Maytag Top Load - Bought a new washing machine less than six months ago... extremely noisy: Clank, Clank, Clank, Clank, etc. Reviews said it was just noisy, nothing wrong with it. Last week it would not spin the clothes dry. Now when it is plugged in, it does nothing but run the pump! No lights, no water. Also the deep wash was never deep at all - barely covered a modest load of laundry. Repair coming today. Wish I could return it.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

I bought a Maytag electric stove steam lift oven 2 years ago, I regret it. I baked a pie, and used the steam cleaning, it didn’t clean, my oven is still dirty. The top of the stove is not easy to clean and scratches very easily. It’s not my first stove, different brand, and I never had problem like I have now. I should have stayed with the brand I had before. My other regret, I should have read the reviews.

The problem with this dryer (MGD7230HW) is the sensors for drying time dont work. The dryer keeps going even when the contents are dry. Have to use manual timer to conserve energy. Not worth the cost.

We bought all new appliances for our remodel. I wish I could return this dishwasher. It has a problem with the door staying closed. I added images of how we are able to make it work. A service person is coming by tomorrow to put a new latch on it (I read several reviews saying the latch is messed up). So I made sure the service person is coming with the part. I called Home Depot when the problem started (used for up to 5 washes or so). And Home Depot wont return it! I called Maytag and they tried selling me an extended warranty and I asked what about the 10 year warranty the machine is supposed to come with? I guess thats a joke as the lady told me I should of read the fine print. So buyers beware! I wish I would of know about Maytag. I would have about a Samsung instead!!!

Purchased Maytag Bravo High Capacity Top Loader Washer in 2011. Purchased at Lowes. They were great. I did not get the product warranty. Wish I did. At first seemed great. Washed comforters and clothes come clean. It does always get off balance and takes a while to wash the clothes. Well I am on my 4th time having it repaired. Put over 400 into it. Now it is leaking. Going to cost another 300 to fix. Only going on 6 yrs old so done. Just ordered a new washer LG Top Loader with warranty praying I have better luck with this washer. Just wanted let you know I had no luck really. Thought Maytag was a better product. Sad to say not for me???

My dishwasher is two years old and it just stopped working. I called the store I purchased it from and they sent out a repair man. He told me that the control panel was damaged and that he would have to replace it. The cost is $145.00 plus the $50.00 service call. He said something must have spilled and got into the control panel. It is a built-in dishwasher underneath a kitchen counter. I think it should somehow be protected against spills and/or moisture getting into the control panel as it is underneath the kitchen counter. I do not remember spilling anything that ran down the front on the dishwasher. But even if something spilled, if it was made properly it should still be working. I will not recommend a Maytag to anyone and will also spread the word about what happened. Unhappy in Pennsylvania.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

Do not buy this dishwasher unless you get the extended warranty. We purchased this dishwasher in Jan 2014. The first one delivered was completely busted up (which was probably the delivery companys fault for not handling it correctly). Then we had to wait for the replacement one to come in to get installed. In Sept 2014 the control panel stopped working. It was repaired under the warranty but it took several weeks for the authorized repair shop to be able to come out, diagnose, order part, and then come back to fix it. Now March 2015 (5 months later) we had the same exact problem with the control panel. The repair company was unwilling to order the part to bring with them even though they already had it in their records what we needed due to the previous repair. It was going to $300 to repair it since they only warranty the repair for 90 days. We decided to replace our 14-month old dishwasher rather than put any more money into it. Shame on you Maytag for putting out such a bad product - obviously this is a common problem. It is quiet and does a good job of washing but to have it take several weeks to get a repair done combined with having a problem that cost 50% of the purchase price to replace twice within a year of each other, absolutely not worth the money. Should have just spent the extra on a higher quality product. Will definitely get the extended warranty on whatever we replace it with.

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

Deceptive company and won’t stand behind their product! Purchased brand new washer. Identified and reported noise that I can hear upstairs in my house while washing to technician. Changed a part, not related to the noise. Called back out. He admitted he could hear the noise. Whirlpool engineering department says normal. Sorry, I should never hear a clicking noise upstairs with two closed doors and 150 feet between me and the washer. Will be going back to Samsung next time.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

Frigidaire makes a good fridge. It works good. It has an alarm when you leave as door open. Great appliance. If I could afford it Id get another one when this old model I have gives up on me.

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

I read the reviews before I bought this washer, went to a major department store to buy it. This way I knew that I could get good support if something happened to it. Its been 3 months, I use the washer everyday. There are 4 adults in my building, they use it daily. I have never had a problem yet, the clothes come out cleaner than the front loader I have. It seems Maytag still makes a good product. I am the first to admit, when you make large number of products you will have some with a defect. But this washer the Centennial by Maytag works great.. Plenty of water in the tub, the clothes come out clean.. Maybe those people having problems need to stop buy at big box home centers. Theyre known for lumber not washers.

This set of Maytag washer/dryer are nearly nineteen years old now and are still workhorses! They keep getting the job done time and time again! Absolutely no complaints. Absolutely and completely amazing!

Maytag Bravos XL washer and dryer. Best washer and dryer I have ever owned. I have owned about every major brand and these are by far the best. My husband is a hog farmer and the washer does a great job. I will always purchase Maytag appliances.

We purchased the washer and dryer pair...beautiful looking, no agitator, water efficient. Load sensing feature. TERRIBLE, TERRIBLE, TERRIBLE. WORST APPLIANCE WE HAVE EVER PURCHASED. Used it 3 times. Clothes would not rinse, left white soap residue in the folds of the black clothes, even after a second wash. Home Depot was just the GREATEST, they replaced it for us. We went with a less expensive model GE. With the agitator and full water load...save yourself A LOT OF TROUBLE, stay away from Maytag Bravos XL.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

Maytag Refrigerator Model MFI2665XEW6 piece of junk. * Builds up ice on bottom of freezer * Bottom freezer door will not close * Annoying alarm sounds* Water leaks on floor

Washer does not clean very well, clothes are left with spots. The water level is never comparable to the clothes thats in the machine, it causes me to lose a lot of water as well as detergent. This machine is the worst washer we have owned. Its also very noisy.

We purchased our range in May of 2012. It is now November 2014 and the stove has had three brains, three ignitors in the oven and one ignitor in the back of the stove. When I set it to bake at 350 degrees, the oven heats up and I put the food in the oven. When I go to check the food, I find the oven stone cold and the brain is still displaying 350 degrees. According to Home Depot Warranty department, if the oven has been fixed three times for the same problem, then the unit is considered a LEMON. Ok, what about the three brains? What about the three ignitors? The ignitor in the back of the stove controls the oven as well. SEVEN times for a technician to come out and fix my LEMON stove is ridiculous. California has lemon laws. I will file suit against Home Depot, Whirlpool, A&E and Quality Appliance if this stove is not replaced within the next seven days. IT IS A LEMON! I have lost way too much food in this oven because I dont know when it shuts off.

We purchased Maytag dishwasher model #MDBH989AW53 in January 2010. June of 2012 the control panel died. Luckily, we had the extended warranty. The service company came and replaced the panel. 3 weeks ago, the panel died again! The service company replaced the panel again. Today I got home and the dishwasher is completely dead! I am so furious!!! At this point, I may just have to bite the bullet and buy a brand new machine. This should NEVER happen to an appliance that is so new! What a laugh regarding the Maytag quality! It is the WORST I have ever seen in my life! Stay away from Maytag!!!! Buyer beware!!!!

My wife told me yesterday she was getting a f51 code... went on you tube and took the top off and the clothes holder out, found 1 quarter and 3 dimes... put it all back together... same thing... took the back off... hoses off, unplugged it and the allen that holds the motor had backed out... no more maytags for me... Tightened the allen, all is fine for now... my opinion, this should never ever happen... No lock washer anything engineering to prevent this from occurring... My grade: replace the engineer...

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

My brand new top of the line Maytag Bravo washing machine lid was broken and locked and would not open. I had clothes in there getting moldy. Three days in Pacific Sales trying to get help. The washer, of course, is under warranty (about 90 days). Finally a repairman came out from Appliance Doctor. He had no clue what he was doing. The company was rude. Then Maytag said High Tech was coming out yesterday, Monday, Dec 16, 2013 between 8 and noon. It never happened and when I called High Tech, he was rude and said it was not on his calendar.Maytag will not give my money back or a new machine or provide a competent repair company to fix it. I will be giving away the 1000.00 washing machine for someone else to fix and buying another brand. I would never buy Maytag anything after this experience. Please note, this is the first time I have ever complained to Consumer Affairs. Thank you for your time.

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

We have already replaced the motherboard and now it is throwing a code of and it takes a whole day to keep pressing start to get one load down. I hate these machines and tell everyone NOT to buy one. They are expensive to buy and too much trouble to fix or repair and too much money to fix. BUYER BEWARE!!!!

Belt broke in inside under tub after 13 months $150. Now another year and I am getting an error message F51 and it stops washing. Im done. Old Maytag lasted 14 years. This is done in 2. Im not paying any more to have it fixed for whatever F51 is. Im cutting my losses now. Hate this machine the way it washes anyway. Always feel like its gonna take off for Mars to join Matt Damon. HA. I try to laugh to stop being mad. Dont buy these. It gets no stars. And after reading other reviews, it deserves none. Shame on this company! Ugh, its making me put a star rating. But I say none.

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

After 9 months, the $850 Maytag Bravos started making extremely loud grinding noises during agitation cycle. We had 5 repair tech visits from A&E Repair, Maytags national repair vendor (and several cancellations + unscheduled visits by same). Each tech said a different part needed to be replaced requiring weeks of waiting for parts deliveries and getting huge boxes delivered to our office and dragging them home since my husband and I work for a living and are not home to accept large parcel deliveries. We had to unpack the washer basket in order to get it into our car and saw it was completely damaged. After 4 months of tech repair visits, using my home as a repair shop, forcing me to take days off from work and still no resolution to the problem, I was finally able to get Maytag to replace the machine. Our previous washer was original to our 25 year old house before it died. Unbelievably, the new Maytag has the very same problems and we are back on the same merry-go-round. This has become a part time job and super headache. I have never had such a horrible experience with a purchase or company. This is not a case of heavy usage either. We are ready to dump this machine! Do not buy a Maytag or affiliate product - Maytag is the worst!

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

First off, the drum split apart on the dryer. The drum part was not in this country, so instead of going ahead and replacing the clothes dryer, they told me to hang the clothes outside for six weeks or whenever the part comes in. That was three months after owning the piece of junk. I was having a bad day already, so I basically completely lost it. Im surprised I didnt get arrested for that. I wont ever lose my temper like that again. The clothes always smell bad, and sometimes really bad. Now, I find out that both washer and dryer could cause a fire. They are sending us a couple of really cheap GFCIs to keep them from a liability issue. Maytag is the absolute worst!

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

This dryer ripped a gaping hole with sharp shards of metal exposed. It was working fine, and then it made a weird noise. It stopped and I assumed my laundry was done. We go to remove clothing and cut hand open on exposed metal. As if that wasnt bad enough, several hundreds of dollars in clothing had cuts in them. This dryer worked great for years, and out of the blue this happened. Im a widowed disabled mother, and cant afford a new dryer.

Purchased dryer less than 6 months ago and now have an issue with the powder coating bubbling up and flaking off on the dryer drum. Maytag says not covered under warranty unless found in less than 30 days. If I had know that I would not have purchased the dryer.

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

Ive had this Maytag for more than 15 years and it still works well. Its a basic fridge, no special features. Just keeps food cold or frozen. Freezer at top, fruit & veggie bins at bottom, cheese bin. No problems, good performance.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

My dishwasher racks are disintegrating. I called to see what to do or if there was a recall. I was told that problem happens a lot, but there is no recall or other option other than to purchase new racks. I could almost buy a new dishwasher. I bought Maytag so that it would last a long time with few repairs. That has not been the case with this dishwasher. I had a medium grade Sears’s dishwasher for years before I supposedly upgraded to a better dishwasher. Maytag is obviously an overpriced name and the quality of their product is no better than any other cheap dishwasher.

Maytag Centennial - It came with the house. I think its a line made special for rent-to-own kind of places. I cannot stand the washer. It will not take fabric softener unless its in the ball and if you use extra rinse you dont get to use fab softener at all. (I like liquid fab softener on some things). Why it doesnt have a dispenser is beyond me. And the bleach dispenser is poorly designed, too close to the tub and splashes every time. Ive had this six months and would get rid of it in a heartbeat if I could afford to. Plus it snags towels. The washer is crap. And its a Maytag. I wish it would break so I could justify buying one that has some decent features like fab soft dispenser, bleach dispenser that doesnt splash, drum that doesnt snag.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

We bought a Maytag 2000 Series machine about 2 years ago. At first the machine worked great, as a new machine should. Then, after about 7 months water started pouring out of the top dispenser for detergent. I read the manual and looked online at the Maytag website for common problems. It said that sometimes small clothing gets sucked through the hose and needs to be unclogged. I followed the instructions to fix the problem. It worked fine for about 2 weeks later during the middle of a load the machine would stop and give me error codes. I looked these codes up and now I have another clog on the drain tube that needs to be fixed. Lo and behold these 2 problems have been continuing ever since. I cannot do a load of laundry without getting a code and having to take the machine apart. I called Maytag to explain my situation and the customer service representative said that because I fixed the problem myself at this point there is nothing that can be done. They do not guarantee that their equipment will work nor will they help solve the problem. I cannot believe that we spent so much money on something that I cant use. Not to mention the fact that when I do complete a load some of the clothes are ruined by the machine ripping holes in them. I would not recommend buying a Maytag because they dont care about customer satisfaction or the quality of machines they sell.

I purchased the Maytag Atlantis Washer and dryer in 2004. I had the washer transmission replaced in 2006, I believe. For about a year now, the washer makes an awful screeching noise. I am not sure if its towards the end of the spin cycle or the rinse cycle, or both. In addition (and over the last 3-4 years), the dial sticks or stalls every delicate cycle. It will stop during the initial agitating and all you can hear is a ticking noise, in which you then have to manually give the dial a slight turn for the cycle to continue. It does it once on the light delicate and twice on the normal delicate. It really is a shame that Maytag is not acknowledging all of these problems as it is not feasible for most people to have a spare $1500 kicking around for a new washer and dryer every time they unfortunately buy a lemon. My previous washer and dryer were 25 years old and still working perfectly when I decided to part with them because they were fairly small. I dont even ever recall having any issues with either one of them in the whole 25 years that I had them. To see all of these complaints makes me more irritated with my appliances and my selection!

I bought my Maytag Dishwasher (mdbh979aww3) about two years ago and just last week, the control buttons on the right stopped working. I see on this site that someone else had the same problem and explained that the wires got corroded, so now Im not sure I even want to replace the part when it only worked for 2 years. Now Im stuck buying a new dishwasher.

Maytag model MBF1958XEQ1 frost build up and ice build up bottom freezer 2011 model. Recently refrigerator not able to stay cold. Contacted Associated Service Corp. because my fridge had a ten year warranty on the compressor only. It cost me $377 dollars to have a service tech change the circuit board and remove a rubber drain valve that was blocking the excess water drain to the evaporator tray. It is working well now but will keep looking for ice build up.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

I paid over $600.00 for a new maytag washing machine two years ago. It quit working a few days ago and the man said itll cost over $400.00 to fix it. Why do you people build this type of junk? I would like to hear from someone on this and why I had to pay $300.00 a year for a washer that is totally worthless now??????? ** please contact me. This is crazy to buy this washer and it only last two years.

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

Purchased Maytag Jetclean Dishwasher Model # MDB7749SBM3 on March 19, 2014 and on June 10, 2017 the washer would not go through the cycles properly. So I got on the internet to check out the problem. Maytag has very flimsy wiring circuit on the back of the control panel that rusts out due to being close to high-temperature water. Obviously a design flaw. The only way to fix it is to replace the control panel for $150 dollars with another flawed part. Do not buy Maytag dishwasher.

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

Two years old, single person owned and will not operate - At 2:00 am, April 25th, 2012; I went to take a load of laundry out of the washer. It was still full of water and would not operate. I am a single person. I do not do load after load in two years. In fact, I was doing a weekly load of clothing, nothing large. I paid close to $1,000.00 for this unit. This sucks and why only one year warranty? Are you Maytag? A Youigo car would run better than this. And they are built cheap.

I have a Maytag Clothes Washer. Lid Closed Light is flashing and agitator will not spin. Troubleshooting shows when the washer does not detect the lid is closed the agitator will not spin. I went to Maytag Canada website and chose Live Agent. There is no Live Agent! You get a Virtual Assistant that does not work; bad software. Virtual Agent shows connected. I type in the details of my issue and the Virtual Agent responds with No Input Detected. I type in the details again and the Virtual Assistant responds with Connection Closed, try refreshing. Over and over again. Tried calling the Maytag Canada 1-800 number. I have now been in the queue for more than 40 minutes. Just stupid cycling for a recording for common problems dealing with products that are not a washing machine (about a 9 minute cycle). NO CUSTOMER SERVICE. Avoid Maytag, Whirlpool and Kitchen-Aid products. Buy from another manufacturer that has live people working at the company.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

This washer is a piece of expensive junk. It was used sparingly (2 people using it) for 16 months when a repair service had to be called. The estimate to fix the machine ($980) exceeded the initial cost. It did not clean the clothes adequately when it was working. There was a powdery substance on the clothes when they were removed. The clothes were always bunched up and intertwined. Only the proper type and amount of soap was used. I cant recommend this washer to anyone. We were very disappointed since we have always purchased Maytag washers/dryers. Never again.

2 Year old washer. First the actuator was replaced. A 150.00 charge. Two months later the pump is shot. Another 200,00 to replace the pump. This is worst piece of ** washer I have owned. I would not recommend to anyone. Stay away. I would give it 0 stars if I could.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

A month ago I purchased a 25 cu ft side by side. First the recirculating fan quit. It was repaired. But the water and ice hose in the door froze and cracked the entire freezer door. Must be replaced, unfortunately they dont have any, so I was quoted 6 weeks for a new door, that has turned into 12 weeks and they cant guarantee me a date. I requested a replacement fridge and was told, They cant do that. I purchased the full Maytag package - stove, dishwasher, microwave. I expect better customer service than that, Take a door off the assembly line and ship it to me.

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

I bought a set of 4 Maytag kitchen appliances. Terrible quality. Dishwasher racks poorly designed for anything except standard size dishes. Microwave has a hotspot and explodes whatever Im reheating. But refrigerator is the worst. According to my service man, Maytag is aware of known issue with poor quality evaporator coils that erode quickly, leaking freon. Causes problems with ice buildup in freezer, poor ice production until it loses enough freon to stop chilling correctly causing food spoilage. Im to that point now. This fridge is only good for offshore fishing site. Whirlpool is aware but will stall as long as possible, then refuse replacement, but they will offer to help you replace the appliance. HA! Fool me once, shame on you. Twice, shame on me.

My Maytag dishwasher control panel stopped working. The control panel failed, it was replaced. The replaced control panel failed. The control panel failed again and needs a fourth (4th) control panel. I have had to pay for service calls and control panels. I only use it 1 to 2 times per week. This is obviouly a lemon. I would like it fixed and to be reimbursed for the lemon part and service calls.

Purchased a Maytag refrigerator less than two years ago. Model M1txegmyb that was nothing special. Main purpose was to keep food cold/frozen. Now it makes noise and will not freeze anything. We called Maytag and they told us to take a hike or pay $469 for a new compressor on a fridge we spent $650 on. I would never buy their products again because the quality is so poor. Reading the other comments we have decided to throw the unit out at this point as we have pledged never to give Maytag another dollar.

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

Similar to dozens of others, we purchased a Maytag dishwasher from Home Depot in March 2011. Recently, it stopped working, dead - no lights, no action. Called Maytag and they referred me to a Maytag Repairman: Coastline Appliance Service of Huntington Beach, CA. The serviceman came out and spent 20 minutes, checked the door switch for continuity, and declared the control panel bad. How do you know its the control panel, I asked. Its my gut feel, based on experience, he said! He charged me $129 for the visit and said a new control panel would cost $380! After reading other posts online, I can only conclude that a new control panel (if that is, indeed, the problem) will also go bad in the next year or two. So, like so many others, were off to buy a new dishwasher - and we will never buy a Maytag or Whirlpool appliance again.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

Maytag washing machine Model # MHWE500VW - 2 control boards only last 4 years. I paid top dollar, $1229.00 to be exact and the parts and labor are $659.00 with no guarantee that there wont be further problems. Technician told me that this is typical of Maytag products. Contacted Maytag and they told me to take a hike and have a nice day. I will attempt to get some help from the place of purchase, Hamai Appliance, Maui, Hawaii.

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

We used to own a Neptune Model. After always leaving the door opened and following the recommended monthly cleaning and many extra cleanings with diluted bleach and water, we could not get the smell out. We paid for a new seal, Advice from Washing Machine Repair service even though we paid a lot for an extended warranty. We had to pay for this ourselves. We also had our year to year maintenance. Because we could not fix the issue, nor would MAYTAG, we donated the set to donated it to Salvation Army.We decided to give MAYTAG another chance, so we purchased a brand new FRONT-LOAD WASHER and DRYER in 2014. As I would repeat the same regiment, I would notice little black specks, so I would clean it an extra time with Afresh. I have continued to this date, repeating the same regiment of keeping my washer clean and serviced as we should, I now have the whole tray dispenser spotted with LARGE black goo that smells. So I have continued to clean my Washer.After returning home from the Cleveland Clinic, I was ready to do our laundry from the trip, more black goo and smell coming from my Maytag front-load washer. My sister had stayed with my 86 year old mother and had wash a load of towels while we were gone. She left the door opened also as she was instructed many times, and that is how we found it. So I took the dispenser tray out as usual and bleached it and scrubbed it. As I did this I noticed bigger areas of goo. I looked in the dispenser housing and OMG it was covered with black mold. I am appalled that our $900.00 Washing Machine is like this. This IS BLACK MOLD, There is no way to remove this mold. I have the sides and bottom cleaned with bleach, BUT I cannot get into the multiple crevices.I called Maytag and I was initially told by a Maytag Customer Service Person said that it sounds like BLACK MOLD and MAYTAG COULD DO NOTHING! I asked to speak with a supervisor. At first she seemed a little put off, but as we talked she became more pleasant, I offered to send pictures or a video of the WASHER WITH THE BLACK MOLD and she said no. She told me to pour bleach into each dispensing compartment and the drum. Then run a wash with no clothes on all HOT WATER 2 times, then rinse 2 times and this should get rid of it and to also leave the dispenser drawer open a crack as well as the door after each wash.The Supervisor said ok and thanked her for her help. Then she said good luck and thanks for calling MAYTAG. Ive did and already do everything our Washer manual says to do on cleaning and maintenance of my expensive Maytag Washer and dryer. The manual says nothing about leaving the dispenser drawer open a little so it dries. The bottom of the housing looks great from doing this, along with me scrubbing it until 5:00 am with diluted bleach water. However, in the MANY SEAMS, CREVICES, THE SCHUTE AND POSSIBLY THROUGHOUT THE WASHING MACHINE IS BLACK MOLD that we cannot access without disassembling the machine and voiding our extended warranty.MOLD GROWS RAPIDLY and causes many illness. I already have an ongoing illness since childhood, I take care of my 86 year old mother, my husband just finished cancer treatment in January. We certainly do not need any other health issues. I called my local Appliance repair company and they said that they normally do not handle anything like this, but if my husband couldnt take the outside of the machine off then the top I could pay for a repair person to come out to take it apart then call and have them come back to put it back, pay them again to reassemble our Washer.I believe Whirlpool in its purchase of Maytag has taken a Monkey on its back. Maytag will do nothing, why should they? They already have their money from when we purchased our machines along with money from many other consumers who also have ongoing issues with their WHIRLPOOL/MAYTAG Front-Load washing machines. It is undignified and deceitful how they treat their consumers with such disregard when we have filled their pockets by being loyal customers.Word of mouth is good or bad advertisement for any company. Everyone who has unresolved issues of any kind can write a formal complaint to the CEO and President of Whirlpool/Maytag. The address is on the internet. Shame on Whirlpool/Maytag for taking many consumers hard earned money, when apparently some of Whirlpool/Maytags money is ill gained by developing and manufacturing a consumer product that causes black mold and marketing it to sell to us, the consumer. THIS IS A SERIOUS ISSUE WHIRLPOOL/MAYTAG. OWN UP!!! My advertisement begins today!!!

I have a Maytag Neptune (model number MAH5500BWW and serial number 85981207AE). On February 22, 2012, the washer started smoking and a burn smell was apparent. Fire department was called. They pinpointed issue to the washer. On February 23, 2012, I spoke with Brenda from the Safety Department. She prioritized a diagnosis from a local certified technician. On February 24, 2012 , the technician diagnosis was defect motor and control runs hot after load. Then Lorna from the Safety Department stated they will not cover part/labor.Machine is

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

I have not found one feature that impresses me. Clothes do not always get clean (folds of debris). They do not spin dry enough. The cycle choices are ridiculously complicated. You cant add any clothes once the load has started. You have to wash the machine on a regular basis at about $3 per month. To get more water in the machine, you have to elect the Bulky cycle. Small amounts of bleach is so concentrated that clothing elastic is deteriorating and small holes may appear.The clothing most often comes out of the machine like twisted up tangled donuts. The cycles take about an hour and no longer match up to the dryer time - more trips up and down per load. The cycle guide is way too complicated - Normal Heavy, Heavy Duty Regular - whats the difference? Two service calls tell me there is nothing wrong with the machine - get used to it. I would much prefer the old agitator machine.

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

I purchased my Maytag HE washer from Home Depot. I immediately started getting spots on my clothes that looked like bleach had taken the color out. After trying 3 times to get a tech to my house, he came in and looked at it a few minutes. He said nothing was wrong and to run a cup of water through it. I called back the next day (5/17/11) and told them Im still having problem. They told me to call the appliance team and have a different tech come out. I called and left a message. No one called me back. I called the next day and asked for a supervisor (Kitty), who gave me specific numbers to call. I called an appliance repair, who was leaving on vacation and gave me yet another person to call. Finally, I got Scott out to look at the washer on 5/27/11. He said the only thing he sees wrong is it got very sudsy, so use less soap. I started using the smallest amount of soap and diluting it with water, running the washer on the bulky cycle and running water through the machine if I ever used bleach. Did it solve the problem? No. Finally in December 2011, the machine ruined a very expensive shirt. I called Maytag and was informed that if a tech comes out, I would have to prove the machine has failed or they would charge me. I have contacted Maytag and informed them of everything, including all of the damaged clothes. I was told they could not compensate for consumer error. I informed them the only error I made was buying a Maytag product, and I will never make that expensive error again.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

Purchased Maytag MDBH979AWW serial #FY4202009 from Lowes October 30, 2009. Control panel went out after warranty, and we replaced it. It quit working again in May 2012, and we replace the control panel, and then in November 2013 it quit and we replaced the control panel along with a new door latch just to be sure on December 4, 2013. The dishwasher quit working mid-cycle a couple of weeks ago only 9.5 months since we replaced the last control panel. Im fairly certain it is the control panel again. We have paid more to replace control panels for this dishwasher than we paid for the original appliance. There should be a recall and compensation on this issue. Very disappointed that Maytag and Whirlpool do not resolve this issue. We will be buying a different dishwasher, and it will not be Maytag or Whirlpool.