I have owned this washer for 3 years and purchased it to match the Centennial Dryer and because of its advertised commercial grade components. The washer has just now turned 3 years old and has never been abused but I have been told the drum bearings are going out.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

Disturbing that this product made it into production. I have the matching dryer too, and its just as bad. First the washer rolls up clothes into a tight ball better than I could do if I did it by hand. Then it spins, setting the wrinkles in thoroughly. Then, even though I shake out the clothes before putting in dryer, after the clothes come out of the dryer (without letting them sit in there) - the clothes look like someone drove over them with a car while they were rolled up in a ball. Bonus: the clothes dont even get dried. Ive watched the clothes in the dryer, the drum is designed so the clothes stick to the outside of it and go around, they never actually tumble or get any air circulation. What a disastrous product.

The dishwasher is only one and a half years old and like many others are having trouble with the control panel. The model is MDB89495AWO which cost nearly $800. The dishwasher does not shutdown after an operating cycle. On contacting Maytag with the symptoms they advised that they have never heard of a similar problem. On reading the comments/experience of other Maytag owners I am undecided whether to scrap this unit and buy another make!

Dishwasher is just 2 years old. Touch panel is bad, not Maytag of old. Waiting for the corporate apology. Seems to me that this is a common problem and a case of poor engineering. Also seems like a case of the middle American getting worked over by the big corporate giant. Not happy. Will not suggest Maytag to anyone. Not looking forward to having to replace something that should have lasted significantly longer.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

Was so excited to get this machine so that I could wash larger loads, including blankets, but unfortunately the machine didnt really clean as expected. That was very frustrating, but even more upsetting was when it began to sound like a jet engine when in the spin cycle. In researching this online, we have discovered that it is probably the bearings. When we called for service from the local store where we purchased the washer and dryer, we were told that it will likely cost at least $600 to repair. We have looked online to see if it is something that we can do ourselves, but really dont want to attempt this as it will require some heavy lifting and a lot of time. I am amazed that a machine like this would fail in such a short period of time and would like to add my name to the list of people who will not buy Maytag again! If a class action suit is ever filed against Maytag for this poor excuse for a washer, count me in, but unfortunately I will probably need to buy a new one before much longer.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

I purchased an expensive Maytag washer & dryer, top loading, energy efficient, only to find it now shreds all of my towels, robes, dress, undies etc. Maytag reply was to put things like undies, t-shirts, & dresses in bags to wash... What about towels? I had an expensive white Terry cloth robe from Neiman Marcus which is now shredded, Im showing it to everyone. Plus the dryer has an area above the front door that snags everything. I open the door & clothing is hanging there, caught on this area. Tell everyone not to buy Maytag, theyre rip-off. Ive lost more money on ruined clothes & linens than the trash washer & dryer are worth, but Im disabled, handicapped, 61 yr old who cant afford to buy another new washer!

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

I own a Maytag dishwasher model number MDB7749cBM 2. The panel on the dishwasher stopped working. It is only a year old. Its too new to break down. Will contact Maytag today. There are so many complaints. Why not a recall?

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

I bought a new refrigerator 6 weeks ago and it is not cooling or freezing anymore. I lost all my food. I spent 50 minutes on the phone to be told that the earliest they can fix it is in three days! Can you believe that? I will never buy a product from Maytag or Whirlpool again and everybody should be aware of the awful quality of their customer service!

Refrigerator - The freezer of the refrigerator would randomly leak on the floor. When I had it repaired on 12/30/14, at a cost of $253.97, the repairman showed me the defective part. He confirmed the online reports that the leaking was caused by a defective part. The defective part had been used because it was cheaper. Now the repaired refrigerator works well. Last month, the control panel on the dishwasher stopped working. According to the online reviews, this is a frequent problem requiring that a new control board be installed. The reported failure typically occurs after the one year warranty expires. My appliances are located in a second home so are only used about once a month. A salesperson at a different appliance store said that appliances usually last from 10 to 12 years. The four years of occasional use prior to failure is not acceptable. I would like to have Maytag repair the dishwasher at their cost. How do I get this to occur?

This machine (Maytag Bravos XL) was in our new house and is relatively new. It is the worse machine I have ever owned. I am 58 and cant reach the bottom of the tub to get clothes out. It doesnt fill with enough water to clean the clothes, and repeatedly I have my clothes coming out dirty. I have had to rewash clothes to get them clean at all. Or they come out with grime all over them. I had both a LG and Samsung front loaders in the past, if I could afford it I would throw this Maytag out on the curb! Its a piece of junk.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

Electronic control board fried after 3 yrs on Maytag Gemini range - certain buttons on control board would not set for ovens. Called Maytag, said was not covered, past 1 year warranty. Recommended repair shops, all overpriced. The piece cost between $300-500 for a 3 year old stove. Cheapest repairman wanted 90 to install piece. Ordered piece online and replaced it myself with help from YouTube video. Maytag has lousy repair records lately. Of 4 Maytag appliances purchased in 3 yr kitchen remodeling… already had issues with 3 of them. Do not recommend Maytag anymore!

We bought the Maytag washer from Home Depot on 5/4/2011 and it quit working on about 7/2014. We had a repairperson look at it and he said the drive transmission is worn out. He recommended that we buy a different machine since the part does not hold up since the part is made out of a plastic fiber material that does not show up. We bought the Maytag because we thought they had good products but a 3 year life on a wash machine is not acceptable. It is installed at our cabin so we only use it part of the year on limited bases.

My $1,500 Maytag double oven Gemini has been trouble from the get go. 1st, trying to broil something cannot be adjusted. It sits 3 to 4 from the fire & there is no 2nd shelf. The control knobs sit on top of the stove & its easy to burn them when cooking. The broiler has always smelled like its leaking gas. Plus, the bottom oven stopped working & we had to get it repaired. The last straw was when the control board went out. We arent even going to try to repair, just going to buy a new stove. No Maytag!

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

My wife was in the kitchen and started yelling for me to get in there fast. I could smell smoke and then could see the smoke in the kitchen and sparks coming out of the front top right side of the dishwasher. I shut off the power to the dishwasher at the breaker panel. I then removed the contents and then the dishwasher itself. I threw it outside and then the next day I took apart the door and found that the control board was melted and fried. The model # is MDBH949PAM1. We are trying to locate the receipt for date of purchase. Pictures are attached. This is not safe and my wife is very upset as our 4 year old daughter had been leaning on the door not just 15 or so seconds before this happened.

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

We bought this washing machine 2 years ago and I was never really satisfied with how it cleaned the clothes. Darker pants would come out with white soap/water lines on them. The worst part, 2 years in, the washer basket seal failed and the bearings rusted. The washer sounds like a tornado every time it runs. I got a quote for $350 to repair it!

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

We ordered a new Bravos washer and dryer at the end of November but due to delivery snafus, we did not have both until the second week of December. Just yesterday, both failed. Part of the drum on the washer ripped off, and the dryer just stopped running an hour later. I am used to getting a long life out of appliances. The old dryer was over 20 years old, and while the old washer was only 17 years old, I thought it would be nice to get a matched set.

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

As many other reviewers have mentioned there is a defective control panel in the Maytag Dishwasher series MDB 7749. I too purchased this model at Home Depot and did not buy the extended warranty. The serviceman indicated that this model is known for its defect yet Whirlpool who owns Maytag does not have it on its recall list. I wrote to the President twice in Sept. 2017 without the courtesy of a response and now learn that he retired effective Oct.1. Is there no-one to answer his emails or is it more likely they really dont care. Sears just dropped them and who knows where their new president will lead this company. Be aware that this model dishwasher is defective and they wont replace the control panel. Too bad as once Maytag before Whirlpool bought them out, was a good and honorable company.

I have a Maytag washer that I bought new in 1995! It is still washing my clothes like a champ. It must be true - the Maytag repairman is a lonely soul, in all these years I have never had to call him!

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

I love my dishwasher. The only hold back is similar to what I hear about all others and that is that it takes a long time. I love that is it quiet, has lots of room and is easy to use.

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

I bought a new stainless steel Maytag refrigerator last year. It had a one-year warranty. Wouldnt you know, 14 months after my purchase, the icemaker stopped working. Did not take out the extended warranty, as I thought I had purchased a quality appliance. I contacted the store where I purchased it. Was told it would cost $150 to replace. I have a feeling this appliance wont last very long. Suffice it to say, I will never purchase another Maytag appliance.

In October 2017, I purchased a Maytag MVWB765FW0, thinking that it would live up to the Maytag reputation but I will NEVER buy Maytag again. This machine is more suitable to wash industrial canvas rather than clothing and bedding. All the laundry is twisted and mangled and ends up in a large tangled ball at the bottom of the tub. My clothing is being destroyed faster than I can replace it.

I am extremely dissatisfied with the Maytag Gas stove and oven. The setting are too high and you cannot simmer something, it burns. I tried the oven cleaner and my oven is still dirty. The burner knobs do not have a click feature. I came home to a house filled with gas. I was not using the top burners, so I must have brushed up against the burner knob while using the oven. I was only gone an hour, imagine if I had been gone longer and walked in the door and created a spark on the rug.

I reviewed lots of reviews, and decided that the negative reviews ones were sour grapes or uninformed customers! WRONG! Do not buy this washer. I replaced a 16 year old Frontloader Bosch! Should have had the Bosch repaired, but wanted a topload for a change, new look etc. From day 2 the washer began to squeal during the early cycle and at the end as well. Maytag repair was out for an unrelated repair on another appliance. I told the tech about it and he suggested its brand new etc, give it time to settle in.Now 4 months in and another service call to tell me its nothing!! It squeals so loud I can not run it while in the next room. I have videoed it and sent it to the Maytag repair in Glenwood Springs, and he said I should load it only full enough to see the impeller at all times!!!! Forget a full load of work clothes or a pillow or blanket. Which is to be expected to be able to wash. He said I needed to spread the clothes out manually along the outer sides of the TUB only, prior to washing the clothes! not over the impeller. I am not kidding! This is a open tub, so the impeller is the little thing in the middle on the bottom. I advised him, I videoed the event and even with three socks in it for a test it still squeals like a (well you get the idea). Trying to get Maytag help, but nowhere. Matching dryer door hinge broke first week, it has been repaired. Not good quality at all for the top of line Maytag. Then Maytag Man must be busier these days, than of old.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

My Maytag dishwasher control panel stopped working. The control panel failed, it was replaced. The replaced control panel failed. The control panel failed again and needs a fourth (4th) control panel. I have had to pay for service calls and control panels. I only use it 1 to 2 times per week. This is obviouly a lemon. I would like it fixed and to be reimbursed for the lemon part and service calls.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

I purchased a Maytag front loading Epic z washer and I paid a great deal of money for it and now I have a broken part on it. We contacted the Maytag manufacturer and they have informed me that the part would not be available for up to two months maybe 6 months. I cannot afford to buy another washer, so now I have a broken washer and need to purchase another washer until the parts come in. I would not recommend this washer or dryer to anyone ever.

The oven works. However, there are two safety issues. First, the flat metal panel above the air vent and below the instrument panel gets extremely HOT. This is the location we can easily touch, especially when we operate the instrument panel. We almost burned our hands. Second, the edges of the unit are very SHARP. We almost cut our legs. These are serious safety issues. In addition, we/I tried to post a review at Maytag site pointing out these safety issues. The review was twice moderate (i.e., rejected). Even though I used to like Maytag, this experience changed my mind.

Does not clean properly! Water level is too low for clothes to move around properly. This appears to be a very poorly engineered product. We have had Maytag products for many years. The only good thing I can say about this product is that it beats a scrub board. Would not recommend Maytag product to anyone. Looking at other complaints it appears that Maytag is doing nothing about this. Will try to sell this at a yard sale and hope no one asks my opinion. Then go buy something that works.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

Maytag model MBF1958XEQ1 frost build up and ice build up bottom freezer 2011 model. Recently refrigerator not able to stay cold. Contacted Associated Service Corp. because my fridge had a ten year warranty on the compressor only. It cost me $377 dollars to have a service tech change the circuit board and remove a rubber drain valve that was blocking the excess water drain to the evaporator tray. It is working well now but will keep looking for ice build up.

Maytag Bravo X-We bought this washing machine not even 4 years (February 2013) ago from Lowes. We had this issue before the warranty went up a couple of times and then it stopped and started working fine. We contacted Maytag before... But of course beings the issue resolved there was no way to send someone out here to troubleshoot the problem. Now it is doing it all the time. A few months ago it went out of warranty. We are having issues with it going into the spin cycle and it will stop there and it will not spin out my clothes and finish draining. Contacted them and they want to charge money for a service tech to come out just to look at it. Lord only knows how much it would cost to fix.

I have used Maytag washer and dryer for over 20 yrs. I recently replaced the set we purchased in 1988 because the washer broke down but I have never had a great problem with it either. I do on a average of 3 loads of laundry a week. I measure my detergents, mostly wash on warm or cold and I keep the filters and machines clean. I would buy the same maker should I need to replace them.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

I have a MGDB850WR0 Maytag Dryer. I have had to replace the thermo sensor/heat sensor three times in the past three years. Dryer takes forever to dry. I spoke to the repairman who told me in confidence that his company receives a lot of calls about this specific dryer for the same reason. He said the part was originally made faulty and thats why it keeps going out. The part being the thermo sensor/heat sensor.

Consumers be aware! Anyone who’s considering purchasing a Maytag Appliance I would highly suggest reconsidering! I bought a $2000+ Maytag fridge Model # MFT2776FEZ00 in March of 2017 and have had numerous repair calls on it: Several for ice maker not make ice, ice freezing in the bucket into 1 big CHUNK, water running down front of door on the inside and outside, to not working at all and ice maker needing to be replaced. Several calls for fridge not properly cooling (temperature was set at 37 degrees F but the temperature in the fridge is 55 degrees F - per 2 thermometers), food is spoiling. The back inside of “Temp Controlled Pantry” is freezing everything and whole back wall behind the drawer is frozen with 1-2” of frost and ice. Defroster is not working and again parts being ordered to repair an obvious issue with this model.I contacted Maytag and their response was “sorry, we can document the problem.” They will do nothing more! These Appliance companies are ripping off the consumers! Everyone passes the buck! Repairman says, contact the Appliance store you purchased it from, Appliance store says, contact Maytag, Maytag says it’s the repair companys issue.

My Maytag model MDB7749AWWI was purchased from Home Depot on March 10, 2011. On July 12, 2012, my dishwasher would not start. I had out of town guests and then the repair person was out of town, so I did not get anyone out to look at it until July 31. He stated that we had bad controls. The parts would be approximately $420.61. He could not get any parts because everyone was out of this part. Does that mean that all the dishwashers of this model number are broken? Is there a recall? This is unreal. When I was asked if I wanted extended warranty, I said no. If I needed an extended warranty, the equipment must be junk. Well, I needed the extended warranty. It is junk! I will never, never, never purchase another Maytag appliance as long as I live!

I would not purchase a Maytag in the future. The top oven does not work, and one of the burners is semi functional. Considering I have only have the oven about 5 years. I am not happy with the the product. In the future I would seek other options, Maytag is not on the list of products for consideration.

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

Please let me know if there is a class action suit. This refrigerator leaks water all my floor every three days or so. I have to chip the ice off the bottom of freezer every three or four days. Storage is also a joke. Poor design.

Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!

This washer is the WORST washer we have ever owned. I should have returned it when I attempted and Lowes talked me into keeping, stating I was just overfilling. I put only a few items and the jeans came out with dirt still all over them!! I have photos. Pathetic. Not enough water, not enough agitation. DO NOT waste your money!

Maytag water efficient, no central spindle top load. Clothes come out with scum on them. Really a problem on the solid darks. I have to scrub with terry cloth to remove. Maytag insists this is normal. Refused to honor warranty. Usually check Consumer Reports for quality and best buy. Energy/water efficiency is important. I like to have some control over the machine so that I can use it the best way for me. Such as soak. This machine cannot be manually controlled at all. Also it doesnt have a lint catcher, doesnt filter the wash or rinse water at all. All the lint and pet hair remains on the clothes or even gets worse.The clothes are not clean. I have no way to control the machine for my use. It may be water efficient but seems to use too little water to clean the clothes. Maytag wants to blame the EPA - This is irresponsible on their part. Its an awful washing machine and they made it. Maytag continued to insist that scum on the clothes was working normally. This scum was added by the machine. I used very little detergent; the clothes were relatively clean - just lightly wore a few days. They come out of the machine with streaks of white scum that I have to scrub off. The clean the machine cycle uses a huge amount of water. This is really DUMB: washing the machine instead of cleaning the clothes! Terrible! And Terrible customer service at Maytag. DO NOT BUY MAYTAG.

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

We bought this Maytag MFI2269DRM01 Fridge/Freezer in June 2016. We have nothing but trouble. First the center rail holding up the Fruit/Veg drawers snapped within a month then the freezer drawer would not close properly which gave us all sorts of problems (door open lights flashing and fridge staying on longer. Lights not working etc.) The service tech came out and tried to fix it and went away saying it was not repaired that he would need a new freezer drawer. In the meantime I had to push the drawer to try and get it to work right. Now the handle is loose and the stainless steel front of the drawer is damaged by pushing it in so much.This repair started in November and now it is the end of March. I asked them to replace the complete unit but they say that the warranty is just to repair. It seems like they have no parts to fix this. Then the new center rail snapped again!!! When they sent the part out to me to install, I found the main frame of the Fruit/Veg rack at the back had snapped. Everything is brittle plastic with not enough support. (The only vegetable that I think I can put in the drawers is mushrooms.) I thought by buying a Maytag that the name sold it. What a piece of junk it is!!! Will never buy another Maytag product!!!

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!

This is a dishwasher purchased at Home Depot on March 25, 2012 for a rental unit... call from tenant said the dishwasher did not work. Repair person from Appliance Hospital went out today and said the control panel is out and the touch pad. Cost is over $500 to replace. I will have to replace this dishwasher BUT NOT WITH ANOTHER MAYTAG.

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

We bought this Maytag washer 3 mo. ago and now need work done on it. We were told that they could not find anyone willing to come work in this area. We live in the Mississippi Delta, 30 miles so. of Greenville, 50 miles no. of Vicksburg or 90 miles from Jackson. So I guess the Maytag repairman is not just lonely anymore, he doesnt exist.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

Like other reviewers, I am having issues regarding the control board panel for MAYTAG Dishwasher Model Number MDB7749SAM0. The unit was less than 3 yrs old when the control board panel malfunction issue began. I feel like this is a manufacturing defect and the company should be responsible for repairing/replacing the control board panel. I contacted Maytag numerous times regarding this, but customer service continues to tell customers there is NO warranty after one year from purchase date, and they are saying there is no recall or other reported issues regarding the Maytag’s control board at this time. However, I have found numerous online complaints and reviews about the very same issue I am having and same poor customer service. Since MAYTAG does not seem to care about their customer’s concerns regarding their product breaking in I feel that the only solution is DO NOT PURCHASE MAYTAG dishwasher brand again. I have had other brands last much much longer than this one did.

Maytag dishwasher model MDBH949AWW - I purchased a dishwasher thinking I was buying the best (laugh is on me). The date of purchase was 1/18/10, the control panel was replaced on 5-25-11 at no charge. On 10-15-12, the control panel failed again so I was forced to hand wash an entire load of dirty dishes. I used the dishwasher once a week. I am debating if it is worth it to repair it or replace it, in light of the fact that it could go out again the next year. Wish I had found this website before I made the purchase.

I have a Maytag refrigerator, Model #MBR 2256KES6, that is only 18 months old. It has totally stopped working. First, there was a large puddle of water on the kitchen floor and then a loud clicking noise in the middle of the night. It does not cool the fridge or the freezer. I cannot believe that a $1300 product is done working at 18 months. I cannot afford a new refrigerator. They should be arrested for selling such junk to the public.

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.

This washer stops every 10 minutes, sometimes taking 3 to 4 hours to complete one spin cycle if it is completed at all. All troubles began shortly after warranty expired. NEVER EVER will I ever buy Maytag again. I make certain that I tell everyone I come in contact with about the pathetic quality of Maytag.

Had the washer for less than 3 months just a week before the 90 warranty was up and it stopped spinning. Called service dept. What a joke for this company that keep yessing you. Took a week before someone came out. Said washer needed a new motherboard and they would only cover it once but there seems to be a ongoing issue with their motherboard. Had to wait over 2 1/2 weeks before they would have one in stock. The tech installed it however now when it spins seems she left the top loose.

I have had the washer and dryer for a little over 2 years. The washer already needs to be replaced as the cost to replace the drum is almost as much as a new washing machine by another brand. Thought Maytag was the very best. I had a GE washer for years before I purchased this set. The GE wasnt broken but THOUGHT I was upgrading..NOT!!! Will not purchase Maytag again. Very unhappy!!!

We have a Maytag washer. It is the noisiest washer I have ever seen! It is in the garage as you could not have this washer in a house. The deep water wash is not deep enough. It bangs and knocks VERY loud! There have been times when all of the clothes are not even wet.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

You can not add water to the fill, blankets dont even get wet when you wash them, you can do double rinse but cant control the fill, have to sit there and lift the lid up and down for 20 minutes to get enough water in the machine! The washing machines have turned into absolute garbage! Wish I would have come here first, whats the difference if I control the load size water or IF I SELECT DOUBLE RINSE? THIS WASHER 200% GUARANTEED I WILL NEVER BUY A MAYTAG AGAIN. ABSOLUTE TRASH FOR $700.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

I will never buy another energy efficient washer again. My Bravos is supposed to save money and be environment friendly, but when you have to wash clothes more than once to get them clean, theres no savings. Ive tried different detergents, cleaned the washer, rinsed twice, added vinegar, baking soda and everything imaginable to get the clothes smelling fresh without any luck. I have had several items ruined because the bleach dispenser pours onto dry laundry. Im disgusted.

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.

I have had this washer for a few years now and it is the WORST washing machine ever. I cant even wash a lightweight cotton blanket. It continually unlevels even with me rearranging the blanket over and over. Ill add some, take some out, whatever. It still wont work. The blanket fully wet is also HEAVY and with my arthritis, is very hard to pick up. I dont think enough water goes into the drum to actually clean the clothes either. The clothes at the end of the cycle come out in a weird mushroom form. And when the clothes do get through a complete cycle, they are twisted so tightly it is hard to get the wrinkles out in the dryer. Why would they sell a machine like this without having testing it more first? Dont get suckered into the Maytag name. Terrible washer!

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

I purchased the Maytag Bravo Series in August 2010. Two weeks ago, I had to replace the idler pulley on the dryer which was no easy task. Now today I was washing a load of clothes only to walk into my utility room and find it flooded. This didnt even start out as a small leak so at least you would have a warning. On the spin cycle, the washer is making a clanging sound. These were not cheap models. I paid $1600 for the set. I will never buy another Maytag product especially after reading all the complaints that people have had about this series. Why hasnt something been done to protect the consumer? I did not purchase the extended warranty as I thought Maytag sold a good product. I owned another set of Maytags that were almost 30 years old when we got rid of them and did minimal repairs over the years. We are only a household of 3. It is not like these appliances are overloaded or abused. Its very disheartening. In this economy, most dont have money to just throw away and that is what I feel like I did!

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

Purchased MBF1958 model refrigerator July 2012. Has had 3 major problems. 2nd time the compressor has failed. For over 1 month have been playing phone tag and given the runaround by Maytag. Never return calls when promised and get a different story with each person I speak with. After 2 service calls to diagnose a bad compressor, $69 service fee, two weeks for the replacement to come in, the third serviceman decides this is not the problem and the refrigerator cannot be fixed. Maytag has once again offered to SELL me a replacement at a discounted price. Do I really want to subject myself to the HORRENDOUS MAYTAG EXPERIENCE again?