Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

Within 1 month Maytag sent 2 repairmen to repair my microwave. I paid $271.20 for the repair and part. The same 2 parts used the first 2 times were ordered again and I was told that Maytag could not get them again. The service and parts are supposed to be guaranteed for 3 months. Maytag refuses to refund me; offering me 15% off a new purchase. I would not buy from Maytag. They lost a customer.

Maytag dishwasher does not clean dishes. It has hot water and we have had a repairman look at it and he said water jets working. We have to wash all our dishes by hand before loading them into the dishwasher to sanitize.

Our Maytag Bravo washer provided so little water, that our clothes were rarely clean. My husbands jeans gradually developed stains around the knees that never came out, and his white underwear & socks didnt come clean either. After about 3 years, the spin cycle developed a loud sound, like a jet taking off, which was so loud and forceful, it sounded like it was literally going to spin out of the machine. We got rid of the Maytag Bravo after 6-7 years, and Darryls jeans and underwear were clean after two washings. All heavy items, such as blankets, have to be watched over because they always get out of balance several times a wash. We kept the Maytag Bravo, although it wasnt great, and didnt dry clothes completely. These are not machines that you can put clothes in, and just walk away. You have to babysit your laundry.

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

This washer ( MHW3505FW) leaks, is crazy loud, water wont drain, clothes smell bad after washing, defective drain pump, defective mother board. Only had 2 1/2 months and it broke. Maytag refused to refund me and Lowes refused as well. Thankfully I paid by credit card. Am disputing the charge. Terrible washer should be recalled. Many complaints on this washer. Very disappointed and upset.

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

I purchased my home in 2008 at which time I bought all brand new Maytag appliances, well the above the stove microwave Ive had to replace the door handle because it broke off and the oven I can only use the very top or bottom to cook on and I cant move them, otherwise the racks will fall through. I have burned myself numerous times as I cant pull the racks in or out and I found that out cooking dinner and when I pulled it out the rack fell through and my dinner went crashing down and splashed everywhere. Due to this fact I hardly ever use it. I contacted Maytag with no help, told me to buy new racks and those did the same thing so it was a $100. It seems as though the liner cant handle the self clean heat and if you look at my oven, the left side is pushed in. If anyone gets help with this issue please let me know. My model number is MERH865RAS serial # 14348133LX. Oh and my refrigerator is a side by side and I have had to have it repaired twice because my food kept thawing out. That model number is MSD2651KES serial 60869476LV all of these are Maytag products and were purchased brand new from Home Depot.

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

We purchased our Maytag® 4.5 cu.ft. White Front-Load Steam Washer online through Menards and picked up the washer on Feb. 5, 2022. We set it up on Feb. 6, 2022 and it didnt work properly from day one. The washer makes a clicking sound when it spins and also gets out of balance very easily. I contacted Maytag and they referred a warranty repairman in our area. He looked at the machine and said it could be one of two things and it would be a major repair. We would have to haul the washer to his shop and he would have to tear apart the washer to fix. He said it would be a big job to fix and we would be out of a washer for a few days.I also had contacted Menards shortly after we purchased the machine and they told us to contact Maytag. They wanted nothing to do with us and didnt want to stand behind a product that they had sold. Getting major warranty work done on a NEW washer makes no sense to me. I am very disappointed in Maytag and will never purchase anything Maytag again. Dont bother wasting your money like we did!

We too were having a water leak from the French door freezer and a sheet of ice under the freezer drawer. The repairman came and told us that it was a common problem with the French Door fridge and an easy fix. Maytag has a new P type defrost hose that doesnt freeze up. He changed the part, $149.75 bill, and no more problem. Should Maytag have let consumers know this was a part that was failing? Yes, definitely. But at least the fix was reasonably cheap.

Purchased a Maytag washer for my family of 8 because we do a lot of laundry and our Samsung washer failed after 3 years. I thought Maytag was a more reliable brand and was hopeful. The machine stopped working after less than 4 months of service. Manufacturers warranty repair came out and said it needed three new parts, motor, clutch and chip - said it would be another 2-3 weeks depending on parts. So all total without a washer for 4 weeks minimum - call the customer service people (first one was rude and short), 2nd one after 45 minutes on hold - told me the were no other options other than wait for the repair. Four months after a brand new washer and it failed. I requested a replacement option and they said no way. Their hotline talks about a positive customer experience and that seems to be a joke. Not helpful, super frustrated and they do not seem to care about the customer experience at all - terrible product and service

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

My husband purchased the Bravos XL washing machine less than a year ago at Bensons Maytag in Peoria, Illinois. Within months of purchase we noticed our clothing coming out with stains they didnt have prior to washing. After hundreds of $$s of clothing ruined we realized it was due to the fabric softener dispenser. We cleaned the machine multiple times & ceased using fabric softener. No luck.Today I finally had enough & called Bensons service department. The fellow I spoke with told me, You are not supposed to use fabric softener with the Bravos XL. I asked why a $1000 washing machine would have a dispenser you were supposed to use. He told me it was because people like to use it BUT you werent supposed to use it. I asked, Why would there be a dispenser if you werent supposed to use it. He told me the salesperson should have explained it during the transaction or I should have read the owners manual more thoroughly. I asked how I needed to go about correcting the problem & he told me to clean out the machine with really, really hot water. I explained we had multiple times.He didnt have any other suggestions so I asked about setting up a service call & requested he access my information so we could verify the warranty. He confirmed the unit was under warranty. I asked to schedule service & was told there would be a $50 service call fee. I told him, I would figure that would be under warranty to which he explained it would only be under warranty if it was the machine ruining my clothes. I asked, What other reason would there be for my ruined clothes and he told me if the laundry was being ruined because I used fabric softener it would not be under warranty. So I repeated that saying So you are telling me if the machine is ruining my clothing because I used fabric softener it will not be under warranty? and he got flustered and basically said he didnt exactly say that and they couldnt confirm anything until a tech took a look at the machine. I told him I would have to speak to my husband.So this is my question... why on Earth do we have a company building $1000 washing machines WITH A FABRIC SOFTENER DISPENSER if you are not supposed to use it? I have never, ever, EVER had a washing machine do such a lousy job. I have never, ever, EVER been afraid to put clothing in a washing machine... not even in a cheap, crappy laundromat. Shame on you, Maytag!

I bought brand new Maytag appliances top of the line. I put the stove, dishwasher and refrigerator in and was waiting for the cabinets to be done before installing the microwave, It was a couple of years; I took the microwave out of the original box and had it installed and it made a terrible noise and then shut off. There is something loose or something. I called Maytag to activate my warranty but they said the time is up but I had never opened the box so I didnt know there was a time limit on sending it in. There was no customer service! The stove I bought for close to $2000 has had to have the control panel replaced 3 times so I have to pay every year for an extended warranty just to guarantee I have a stove. Last year I went through the holidays without one because it was out then too! I would never buy another Maytag again!

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

We purchased a Maytag from Lowes about 3 years ago. The spin function quit working properly last Feb 19. We paid $350 to have parts replaced thinking it was a fluke and we would be set for a long time to come. Well, last week the same thing happened... not even a year later. Lowes doesnt care and Maytag doesnt care. They want you to spend more to get a warranty to get you to 5 years... well as far as I am concerned that is not good enough. An appliance should last 10-15 years. This Maytag was to replace a Whirlpool that caught all of our clothes in the agitator fins, so after a short period of dealing with that we paid out for a Maytag without an agitator. So in the span of 6 years... we had about $1,500 of dissatisfaction. I believe our repair guy said they the companies are one and the same. Selling junk ought to be illegal.

I would not buy a Maytag again. I am very disappointed with the noise level this dishwasher produces. I am also not happy with the inside capacity. I never have enough room for all the dishes when I have dinner parties.

From day one I didnt like how this machine restricted how I can wash my clothing. There is no water volume controller. It is all automatic, which sounded fine in the store, but once I used it I quickly realized it is horrible. I can not add extra laundry or detergent in at the last minute because it says not to open the lid at all once you start the load. The settings are very glitchy. They do not seem consistent. There is a knob for level of soil on the clothing which doesnt seem to do anything at all. Ive had it now for four years and it has only gotten worse. Now I can only use one setting Hand Wash. Try doing a teenage boys clothes in Hand Wash and youll find out quickly that nothing gets clean that way. Oh, and all of the sudden the spin cycles are not working, they spin when they want to but they rarely get rid of the dirty water. Spinning in dirty water does not get clothes clean either. This machine is horrible, hands down, the worst washing machine I have ever owned.

No matter what we we do we still have soap residue left on clothes, even when we do the 2nd rinse cycle (what a waste of water). We use the correct amount of HE detergent and we use the detergent dispenser but it doesnt helps. The machine just doesnt use enough water. We have removed items that still have DRY SPOTS on them when the cycle is done. Areas that have never gotten wet after a 45 minute cycle. Never once had this happen with an agitator machine. Would not buy this machine again. Model: C80441070. Serial #: MVWX655DW1.

Perfect for me. It would be better if I had a space to put it without adjacent walls. Mine sits with the refrigerator door against a wall and I have to pull it out to the door space to open it wide enough to pull out the drawers to take them out for cleaning. Otherwise, it has worked very well for me by myself, for me and my husband when he was alive and for my son and his family and myself, and he has 5 children.

Replaced a Maytag Bravos xl washer and dryer in 2015. First year was fine but almost right after the warranty period, the spinning cycle was loud. You cant even have a conversation near the washer. I put up with it after calling the repair department. Because I was told that it will cost as much to repair than buy a new washer. Now the washer does not drain when a small amount of cloth are in the washer. Dont buy this washer and dryer. Maytag is not as good as it once claim.

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

We purchased a new Maytag Bravo washer and dryer on March 4, 2011. On January 26, 2015, our washer stopped spinning the clothes. We purchased these appliances while preparing for retirement, thinking we would possibly never have to purchase them again. There is only two of us! Wrote to Maytag (when it was still Maytag) and got a response of So sorry **, we can fix your washer for $319.00. We could buy a new washer for not much more than that!!!!!

Dryers been installed for 3 months, 3 service calls to date. Heat unit failure. 1st service call no show, no call. 2nd service call fixed the problem 50%, the dryer would heat on timed dry but no other modes. A week after that call heat unit failed again on all modes. Awaiting 3rd service call. Customer Service Department at Whirlpool Canada could care less. Avoid this product, Maytag 2000 series dryer - do not buy.

Front load washer. When load is done. Removing is one long string of clothes... Is a large load washer which I like. But you cannot add any items after you close the door. And you always forget something that needs washing.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

Things that I have read that are true: Rips clothes/towels/sheets. No real problems with motherboard like some have stated. Bought Maytag Bravos Washer/Dryer in 2009. No real problems with the dryer, HOWEVER, may with the Washer. Had the pump go out in 2/2010 to the tune of $199.20 due to a small object in the pump. The repairman said it would just take a very inexpensive part from Maytag to prevent this. In 6/2012 washer not draining, clogged pump. All right, new to HE Washers, so told to use less detergent than detergent manufacturer recommends. $79.13 to fix clogged drain. Even though being careful with items in pockets, loose buttons, etc. AGAIN had pump go in 1/13, $214.22 (same problem cheaper in 2010, repair inflation). Wed noticed it was loud on the spin cycle (like a rocket going off) and were told at that visit the bearings would need to be replaced, and quoted approximately $280 to repair those. Havent fixed, waiting for something else to go wrong and then decide what to do with it. So in 4 years paying almost the purchase price of the unit (if I fixed bearings also). Crazy. If you bought a house and had to pay 4/5 of the house to repair it in that short of a time, no one would own a house!!!

I am replacing my second Maytag Bravos washing machine. My first had heavy use and I rationalized that the 5 year life span was due to the heavy use. The one that I am replacing now is only 3 years old and has only done laundry for one 67 year old woman. It suddenly needed two parts with a repair bill that was going to be over $600.00. I decided it was in my best interest to spend a couple hundred more and replace it. I will not be buy Maytag again. The appliance company that I have bought most of my appliances from recommends Speed Queen which ironically also has a full 10 year warranty on all parts and labor.

Bravos XL washer - I agree with others, if I won the lottery, this would be on the street in two minutes. It is a complete waste of money. Nothing comes clean. Supposed to be water efficient, well not when you have to wash everything multiple times and I have to do them in such small loads to have any hope of anything getting clean. Some clothes just never look clean. I have the same issue with all my dark things coming out with white residue and yet I use liquid detergent. I follow all the instructions and do the monthly Affresh tablet (cash grab) and still nothing is ever clean. I am SO disappointed in this machine. I thought Maytag and Whirlpool were good brands but not anymore. I also get a constant HC error and there is nothing wrong with my water lines. Just so disappointing, save your money and frustration and buy something else!!

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

I have always heard Maytag was one of the best so after replacing too many washers to count in 15 years, like Whirlpool and Kenmore, I decided to spend more for quality. I figured pay a few hundred more once rather than spending $400 for a cheaper one that only lasts 3 or 4 years. That choice seemed environmentally responsible and financially as well. However, I couldnt have been more wrong. In 2016 I purchased the Maytag Centennial top loader for $500. I really loved the size of the tub and the way it looked. I can fit a large comforter in it with plenty of room leftover. I also have no interest in a front loader after reading reviews. So I thought this was going to be great! Well it hasnt been. It has broken 3 times. The circuit board twice and now the bearings are going out in the motor. I fixed it the first two times but now Im done. Im done with Maytag, Aka Whirlpool. I think it will be a Speed Queen for me now. Im hoping it wont be a dud also because they are pricey! It actually scares me to spend that kind of money. I have really lost my faith in most companies nowadays. Customer service and quality has gone out the window. I think about how much this impacts the environment! Its terrible that appliances only last a few years before they end up in the landfill.

I purchased the Centennial Commercial Technology washer in June of 2013. In the last 2 1/2 years it has been repaired 3 times. The transmission had to be replaced twice. My household consist of two adults and definitely it is not overused or overloaded. The washer currently is not working. Consumer service cannot schedule an appointment for repair for 2 weeks. Previous repairs took approximately 2 weeks to schedule a service appointment and it took another week to two weeks to get the part in and washer repaired. I have decided to consider this an expensive learning experience and will not purchase Maytag products in the future!

Bravos MCT maytag commercial technology washer - Bought this washer a year ago. Will not complete cycles. Will not agitate. Never buy Maytag.

I chose Maytag because they received a good rating from Consumer Reports. I liked that they were for extra large loads however now that Ive had them for 12 years I know the large loads are no more than my old Kenmore washer and dryer. The real deal breaker for me is the size of load that you can actually wash. I was hoping I would be able to wash a blanket without worrying about the washer going off balance. My washer and dryer are Maytag although I dont know the model number. They are full size but the extra large load is not extra large. The knob on my washer broke and Maytag wanted $15 for a plastic knob! I found it on eBay for $3. The washer goes off balance too easily.

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

I called customer service to ask if there was some way that Maytag could assist me with repair of this like new dishwasher. When I said it was out of warranty and I had no additional warranty, I was told that a repairman could come out for $110 and diagnose the problem and that parts and labor would be extra. I explained that I had purchased Maytag because I saw commercials, for years, showing that Maytag repairmen had no work. She was very unhelpful and kept droning the same mantra, that a repairman could come out for the above charge. I was very angry and asked for the name and address of the President of Maytag so I could send a letter of complaint. I composed a letter, however: it is Thanksgiving time and I need my dishwasher so I made an appointment to have it repaired. I was told he would be out Mon. between 8 and 5. I asked for a more specific time and was told that I would get a call on Sat. with the time. Thankfully, no call came, because on Sunday, I read the reviews on this site and realized that Maytag was no longer a reliable nor a responsible company and I decided to save myself money and time and stress and just go out and buy a GE. So we will hand wash the dishes on Thanksgiving and buy a GE on Black Friday. This does not mean that I am letting Maytag off the hook. I intend to send my letter to Jeff Fettig at Maytag and also join in the class action suit. How very sad that the name Maytag has become just a name used to shill for defective and shoddy merchandise.

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

I bought this washer about 6 months ago and I seem to get clothes that just arent clean and have marks on my dress pants and my whites are awfully dingy. Never have I ever had white things that didnt stay white. I honestly would never buy this type of washer again. I am actually hoping that there is a way to at least change the water level. Also I hate the fact that I cant add bleach to the water before the clothes and to let the bin fill and mix correctly. I dont think the bleach even gets to the clothes.

How is this fair that only a couple of washers recalled...I knew of no recalls either...My old Kenmore top loader outdated by far. Guess I should have kept it.

I purchased your refrigerator (model #mfd2561heb) in 2005. I bought a Maytag, because I thought it would last me a lifetime. I came to find out it will not. I called Maytag, and got Repair Plus One. The repairman came out without a compressor or capacitor. Now, I have to wait 4 days or more. I have a 3 year olds birthday party, of which we will be working out of our 19 year old Kenmore in the garage, which has worked flawlessly. To make it short, you lost me as a customer, because of this product! I just wanted to let you know. It is sad too, as we enjoyed the refrigerator. Its been making noise for awhile. I thought it was just part of the ice maker. Now, it cost me another $299, plus all the food I had to throw out! There was a big recall of refrigerators from Maytag around the time mine was made. I think that this model should be part of that recall as well. Dont buy a Maytag! They may have had quality at one time, but I just think those days are gone. Thank God for our Kenmore in the garage. I dont know what I wouldve done without it.

Maytag Dishwasher MDB7749SBW3 - Control panel problem just like everyone else describes. Bought in Nov 2014... how disappointing!! My husband is sure he can fix it if I buy the part. I went online to order the control panel, and of course because Im in Canada I cant ship the part directly from the website, I have to call the Canadian Sears Part Dept., its about $200! As I came across all these reviews I am even contemplating if I should waste our time and money trying to fix this thing... Maytag never again!!!

This washer sucks so bad. Just got it a few hours ago and its absolutely horrible. The water just runs for the wash cycle. And I was told by the salesperson at Best Buy that it would save you water. Thats not the case. There is enough water to run over all the clothes. It doesnt agitate enough to even move the clothes around. The clothes basically sit at the bottom of the tub in the water doing nothing. This Maytag Bravo washer will be returned tomorrow. Me and my wife are highly disappointed. I wouldnt recommend this to anyone. Weve decided to just get the old washer fixed and go from there. There are too many bad reviews for this washer to still be on the market. We feel that this was a total waste of time, energy and money.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

We have had this refrigerator (Maytag Side By Side Refrigerator with Ice Dispenser 27 CU) for 5 years this month and have already had to have it serviced once and now the ice dispenser just went out. I wish there was a brand out there that did not have problems and when problems occur, you do not get the runaround to get them fixed!

Dishwasher control board has completely started blinking cancel when not touching it, ran for the entire time I was in Church. Numerous problems, only 2 years old. NEVER would I recommend this brand, EVER!!!

I thought I was nuts - only 2 of water in a full machine of bedding or clothes. I agree with all the other one star remarks - clothes still dirty, still dry, hardly any water and if you use the bedding selection, it takes nearly 2 hours to wash a load and then it doesnt spin dry so you have to rinse and spin again. Very disappointed with the machine. Yes - class action lawsuit? How do we do this.

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

Bought a Maytag MVWX655DW top loader clothes washer from Best Buy on 7-7-2020 it was delivered as promised on Friday 7-10-2020. The people who delivered it were very professional and nice. They did a great job installing it. My wife went to use it for the first time Saturday morning 7-11-2020. Luckily this washer had a see through door. We could not believe our eyes, it never put enough water in the tub to cover the clothes. So as we watched the clothes on top never participated in the wash, they just moved around. When it went to spin cycle it was making a loud clicking sound as it was shaking. So we tried different settings, after 3 loads I called BB and said I want to return it. This machine has been mislabeled, its not a clothes washer, its a noise maker at best. DO NOT BUY THIS MACHINE. IT DOESNT WASH CLOTHES.

The new Maytag commercial brand is different than the traditional Maytags. Uses less water. The new technology in the variety of choices for cycles and the steam cleaning for the dryer is a great feature.

Purchased a Maytag Bravos top loading washing machine in Sept. 2015. First time we used it the machine vibrated enough to shake the walls. We thought the balance was off. Called Lowes (installers) and they came out and said it was level. There was something fishy about the grinding type noise it made. Also noticed that in spite of all the noise that the clothes essentially stayed in the same spot while the basket moved. Sometimes the clothes on top never got completely wet or rotated through the wash water. Called Lowes again and they looked at the machine and said it needed replaced. But the 90 time period for replacement had passed. Lowes said it would be repaired. A technician came and replaced the basket, saying it might have been out of round. He left, we used the washing machine and it was worse. He came back an hour later and talked with Whirlpool and they said there might be something wrong with a gear. Hes going to replace the gearbox sometime. Meanwhile we are stuck with a washer that makes a lot of noise, vibrates terribly and doesnt appear to do much washing. If noise equated to cleanliness then it would be fantastic. But had we known about the noise or the many complaints we would never have made this purchase. Whatever happened to Maytag quality? Bet that Maytag repairman isnt lonely anymore.

I purchased a Quiet Series 300 E71195 dishwasher in 2011. Its about 3.5 yrs old. I guess misery loves company because like so many other complaints on this site my control board died, and Maytag, while saying they care about customer satisfaction, basically said tough luck pal, youre on your own. Sadly I own 3 other newish Maytag appliances. When will these appliances die without support from Maytag? Im not holding my breath. My next step is to complain to the dept of Consumer Affairs and create a page about nefarious Maytag on social media. Avoid the Maytag brand when shopping for appliances. I know I will.

I bought Maytag Bravos X in 2014. I bought a set. The dryer is fine. Right after the warranty was up the washer started having problems. Maytag was no help. One sensor after another went bad. Now I have to unplug it to get it to start and then again to get it to spin. It hasnt spun on its own since 2015. It just recently wont start on its own. I have appliance repair people out and they cant fix it. They say everyone has problems with them. My mother swore by Maytags and had a set for twenty years or so, but now they are garbage.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

Just had the repairman here. This machine is computerized so it won’t last. It does not have a setting that lets me do any load of laundry the way I need to do it. I have to use heavy duty to do a load and then it takes 2 hours. When I want to do a load of sweaters on delicate it will not put near enough water in the machine to wash them. The normal cycle does not add enough water to wash, let alone rinse the clothes. I can’t choose the size of the load based on how much I need to wash so I have to do more loads at 2 hours each or do everything on bulky. Whoever came up with all this needs to be fired. I am extremely unhappy with this machine and I have loved Maytag for years. No more.

Gas double oven - range that has performed well over 12 years old with only one service call for thermostat. Very inexpensive to repair and parts are readily available. Easily cleaned inside and out.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

When we turn up the temp in the oven above 400 degrees, noxious fumes come out giving us headaches and nausea. We have to open all the doors and windows and bring extra fans...very toxic. PLUS the vent for the oven is at the top of the oven door, so the knobs for the burners get so hot you cant touch them!

I purchased a new Maytag refrigerator on September 21, 2007. The refrigerator compressor went out on July 19, 2011, three years and ten months. The repairman said that the compressor developed a pin hole leak and all the freon leaked out. The repair cost appear to be around $300 when completed, hopefully. What a crappy refrigerator. It seems that this is a regular problem with all types of Maytag appliances. Maytag is no longer a premium appliance. Stay clear from purchasing one!

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

Purchased my Maytag range/oven 14 years ago and it still works to this day. I had to replace both oven heating elements. I am a do it yourselfer, took me less than 5min to replace both. The cook top is easy to clean. As long as you take care of it, it should last you a long time.

Maytag model #MDB6949SC, purchased Feb 22, 2015. In early May plastic parts from the top rack wheel assembly broke. Assembly unit replaced at no cost through the 1 year warranty. (cost = time and effort to arrange replacement with repair person). Same parts broke again in November - replaced at no cost again under warranty. Warranty expires in two months. If past performance indicates future performance, this part will need replacing twice a year at ~$140 per visit or $280 per year. Not a good thing. Called Whirlpool and with several calls and emails. They offered an extension of a year on the warranty. I think using plastic for this wheel assembly unit is a design flaw. Would not recommend this dishwasher.

We bought all Maytag appliances two years ago when we redid our kitchen. I have had nothing but a nightmare with my Maytag dishwasher. It started to leak so we called in the service repair person. He said he could not find the leak but tightened something in the washer, it still leaked. We had him come in again because it still leaked and nothing. We called in a plumber to see if he could find the problem. He couldn’t find anything wrong with the plumbing and thought it might be the washer door seal. The washer is still leaking, it will be the third time the repair man is coming to fix the washer. At this point, I just want to get rid of my two year old dishwasher. I will Never buy another Maytag product. This ordeal has been a nightmare with no help from Maytag service centre. So, so, disappointing.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

My Maytag (MDBH955AWB) dishwasher (not even 6 years old) is losing its prongs that help the dishes to stand up. They are corroded at the bottom and snap right off, leaving the dishes without support and banging into each other. We are only a family of 3 so it gets moderate to minimal use. The bottom basket costs $200 to replace, a third of the cost of a brand new dishwasher. Everything else about it is fine but my dishes will be chipping away. I cant believe Maytag made the basket so poorly that it doesnt last the lifetime of the dishwasher.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

We purchased this set 6 months ago. The store we purchased it from is unwilling to help us. Maytag insists there is nothing wrong with the washing machine. The machine doesnt clean the clothes. After a wash cycle there is pet fur and lint all over the clothes, even after it comes out of the dryer. The clothes are all twisted in tight knots when the load is done. The washing Machine doesnt dispense enough water to wash. I have taken clothes out of the washer and the items are dry in spots, most times you can smell the mustiness of a dish towel after its been washed.I used the steam clean dryer to fresh in up the curtains and the panels came out different lengths. Not eager to try that feature again. This is our 2nd dryer set purchase, the last set was 10 yrs old. I couldnt find anyone willing to repair it. I was told they dont make machines like they used to and they are all designed to last 10 yrs and you’re lucky if it lasts 15 yrs. Yes, we contacted Maytag and yes, like the many other folks who have shared their stories we also got the run around. Sad to say we are going to do our research and will be looking for a new machine. Im going to shamefully donate the set to a charitable organization and use the receipt as a tax write off. IF you’re doing your research, DO NOT BUY A MAYTAG.

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

Maytag Dishwasher, mdb7749sam1 - I got this dishwasher new in Feb. 2013 for my new house. I thought that Maytag was supposed to be a very good appliance company. (I just found out that Whirlpool bought them! I dont like their dishwashers, either! Ive had 3 whirlpools that only lasted about 2-4 years each.) My dishwasher worked great until the control panel buttons started blinking and going crazy! Then, it just stopped working altogether. I called Maytag about this part, and found out that it is only covered the first year, and the so-called 10-year warranty doesnt cover it. What good is the extended 10-year warranty if it doesnt cover all the parts!? I researched this dishwasher before I bought it. It got fairly good reviews at the time. Now when I look it up, it gets these terrible reviews! I am so disappointed with this situation. I have other Maytag appliances that have performed great. Im not sure why their dishwashers cant be made the same way.I am going to order the part and repair the machine. I hope this will fix the problem. I had hoped that the Maytag brand would live up to their hype, and be better than the Whirlpools I had already had such bad experiences with. The Whirlpools had great features, they just didnt last! This dishwasher, too, has great features. Two years isnt a long enough run for it to be a good choice, though. Really disappointed :(

My stove is approximately nine years old. During the past year both my husband and I enjoy cooking from recipes 3-4 times a week thus the stove has become essential. Functionality and size is important when trying to cook meals with two or three components. One of the oven racks was missing from the oven when we moved into the house. Even though it is self cleaning, spills pile up between cleanings so it is great that it has a really cool steam cleaning option. Just wish it were 5-6 years newer.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

I would have given this washer/dryer a 0 star, but wasnt able to. Bought the pair and first thing, couldnt get enough water in the tub, clothes wallowing around for an hour in the few cups of dirty water that it allows. Cant even believe how terrible this combo washer and dryer is! Now I get to wash everything in this piece of ____ twice, thank you Maytag! Just took out a load and it is dingy and stinks, so now its wet, on the floor waiting its turn to go back for another wash (possibly even a third).If you want clean clothes, do NOT get this washer. Dryer has issues also. For whatever reason, the AF signal has been on for a couple of months. Turn it off and back on and its okay for a bit, then back on. Its the Air Filter. Its not plugged, so I dont know, I just keep using it with intervals of resetting it altogether. What a total waste of money. Am going to give it away for free as soon as I find a replacement! Save yourself a huge headache and look elsewhere than Maytag. Oh, and if Maytag happens to read my review, you can contact me for a refund any time, just respond to this post, you can even come pick it up and get it out of my home. Thanks a bunch!

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

We have had the oven, a Maytag Gemini Double Oven model mgt8775xs02, for 3 weeks now and I am so upset. First off, I became violently sick from the oven when we first used it. I had a horrible headache and then nauseousness and then the worst stomach problems I have ever had. The toxic smells coming from the oven were too much for me. We had every window open. I looked online and found other people who reacted the same way to their new oven smell. But now we are on the 4th time using the oven. We did a self-clean and I thought that would help but no, it smells like someone is pouring gasoline into my home. I smelled it in pockets throughout my house. I have had the gas company out twice and a repairman. They all cannot figure out the problem. I looked online to see if other people were having a gas problem from this model and I am not finding it. It is horrible. I feel like I am being poisoned. I have not had a working oven in 2 and half years and I was so excited to get this oven and now my new oven is making me so sick. I am not sure what to do from here.

We bought a top load washer and the matching dryer. A thermal switch (I think it’s called) blew in the dryer at about two years. Luckily my husband is an electrician, so he took care of that. WASHER-A little after 2 years the plastic “driver hub” stripped And the agitator has stopped working, the door is having trouble locking and it won’t spin fast enough to get the water out of the clothes. I’ve ordered a new “driver hub” for $53! It is a cheap plastic part. Probably 1 cent to make in China. Robbery. This will hopefully resolve all 3 issues I’m having with the washer. They even charged me 9.99 shipping. $2000 later Maytag/Whirlpool should treat their customers like royalty. I will never ever buy another Maytag or other brands associated with Whirlpool ever again.

We bought a Maytag refrigerator two years ago with the front french doors and bottom pull out drawer. We chose Maytag because we thought it was a name we could trust, a good quality merchandise. However, in the last two months, we started having problems when the fridge wouldnt stay cold, the freezer worked fine. We removed everything from the freezer and my husband found the freezer needed defrosting as the back of the unit was a solid sheet of ice. It took hours to defrost and we thought that we had the problem taken care of.. and that we wouldnt have to worry about this happening again. However, we have now had to do this three times in the last two months!! I love the style of this fridge..but am getting SO ANNOYED with having to rip everything out of the freezer and spending HOURS to defrost it! I have NEVER had this problem with any other fridge!! Im ready to replace it, but weve only had it for two years, and I shouldnt have to be spending a fortune on ANOTHER fridge after TWO years!!

I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

Its unfortunate that Maytag expects their products to be so short lived, they wont produce parts for their appliances after 7 years. They just told me they are only required by law to make parts for their products for 7 years so thats what they do. So unfortunately, if your microwave outlives its handle, youre going to have to replace the entire appliance which will cost me almost $500. I will never buy another Maytag or Whirlpool products because of this.

You get what you pay for, you can go cheaper with no frills and watch how clothes wash, also run afresh through the washer as recommended. Also use the correct amount of detergent. Maytag isnt as good as it once was but it is the top of Whirlpools line of companies.

Purchased new washer mid-February from Maytag dealer. He said machine has few problems and it was a good machine. 3 and one half months later, the machine is dead. No lights on display but power at plug. Repairman comes at appointed time and says it needs a new circuit board. Within a week, the part arrives and an appointment is made to install the new board and still have the same problem. Have to order a new console panel. 3 and a half weeks later, the part comes in. I have a job which I used the money to buy this machine and now the service advisor wants me to take off work so they can try to fix this machine. He told me I cannot return the machine. Whirlpool Canada LP Customer Assistance said they could not do anything. When I asked to talk to her boss, she put me on hold. She came back and said they would give me 6 months extended factory warranty and she would email this which I have not received. Work schedules will dictate when the next appointment will be made.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Brand new top of the line top loader washer. Lid locked mid cycle and couldn’t open it. Called Maytag. Sent a repairman out to fix. Three trips later, 5 parts, and over four months later, still broken. Unable to use washing machine. Been going to laundromat to do laundry. When speaking with Maytag, all you get is a sorry. Now I’m waiting on another part and then schedule another appointment to have guy come install. Maytag would rather replace every part, one at a time, than send a new washer. It is beyond ridiculous for a new washer to have to have all of its parts replaced. It’s a hunk of junk and Maytag will not stand by their product. Worthless company. Will NEVER buy another product from them. Their washer and their service is so far below standards, it’s criminal.

Worst customer service ever. I ordered my washer and dryer from home depot 2 weeks before a possible delivery day. The day before delivery I receive a call that they dont have them and I must wait 1 more week. After 3 phone calls I am promised a credit to my account. A week after delivery I am wondering where my credit I was promised is so I call. Im told the most I can be given is $100. I state that I feel my time is worth more than that. A supervisor is brought in and Im told we will get $150 credit. Then put on hold. She reviews account (why didnt you do this first) and told because we didnt call within 48 hrs of delivery the most they can give us is $75. So I call back very frustrated. Then Im told its our word against theirs that we were offered that?!? What?!? Well I am sure you record conversations and thats total BS. I explained how you cant offer something then take it back. I was told the week before I was getting a credit and my account already notated. No one said, Call within 48 hrs to dispute again to get it. Why would I have to I mean seriously. So after a total of at least 2hrs on the phone before and after delivery I am forced to settle with $75. I feel very unappreciated. I purchased and paid for $1633 worth of appliances that were a week later than promised. Called less than 24 hrs before expected delivery and told they dont even have them. Then told Im getting a credit of $150 to be told sorry now just $75. The lady proceeds to say that she doesnt think it was because of the phone call not being made. What? Are you serious. WELL THAT WAS THE LAME EXCUSE I WAS GIVEN SO I COULD CARE LESS IF IT WASNT THE REAL REASON. THAT JUST MEANS I WAS LIED TO. I promise I will never buy Maytag Whirlpool again. One customer may not mean much to you but good customer service means everything to me.

After 1 year and a month, the dishwasher would not work. When the Maytag repairman came, he told me that this was the 3rd one this month that had the same problem (the control panel). The cost to replace, it would be about $275. However, since I know of 3 that have broken, why would I replace it? I live alone and maybe have used the dishwasher once a week. There should be a recall on this machine. I called to see if there was a recall and was told Im sorry. I would advise anyone purchasing a dishwasher to avoid Maytag or any dishwasher made by them.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

This washer was the biggest disappointment I have ever had. When I looked at it in the store I was excited that the tub was so big and the Maytag Label has always been trustworthy to me and my family. This machine certainly has disillusioned me against Maytag. I can only wash clothes on the bulky sheet cycle because even with deep water wash it only puts about 2 of water to wash clothes. Clothes on top dont even get wet! It doesnt take an engineer to figure out that you cant wash clothes without water. Big mistake! Would never recommend this washer to anyone! I complained directly to Maytag and never received a response. I have had to rewash clothes because they did not get clean. Even with an extra rinse the clothes still have enough soap in them to make my skin irritated. My whites are not white even though I use hot water and follow all of the directions provided with the machine. If there was any way I could afford it, I would throw this machine out to the garbage and get one that actually cleans the clothes. I will never buy another Maytag machine in my life. 

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.