Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

Maytag is the worst washer company. I owned my washer for two years and I had two different problems with it and now I have a 3rd. The first was the same day they delivered the washer, I needed a wire harness. I should have returned it then but I didnt. The 2nd was six months after the first one. A wire came loose due to the washer shaking and the 3rd, Im not sure why it wont drain but the tub is full of water. I called Maytag and they really didnt care as long as they got their money. They referred me to three companies that fixes washer. Two of three was already out for this washer. If I didnt know any better I would think Maytag gets paid off for every customer they referred to these companies. I would never buy another Maytag Bravo or Whirlpool product. Im very dissatisfied with their Bravo washers. They lost a long time customer.

On 9/8/09, I purchased a Maytag ceramic glass top range, model MER7662WBO. The right front dual burner has what look like worms in the burner. The other burners are clear. Maytag has replaced the top three times and the burner once. The top has gone bad again and they are calling this a cosmetic now and will not replace the top. I think there is a problem with the tops. I have purchased my last Maytag product. I buy for looks also.

We had a Whirlpool dishwasher for 24 years, and when it was time to purchase a new one, I did a lot of research before choosing our Maytag. Reviews by other consumers who had purchased dishwashers was very helpful in making our decision, and we have had no problems in the almost 18 months that we have had this dishwasher. It is very quiet. It washes and dries the dishes with no streaks, although I wash off the dishes before loading them. It provides 5 cycles and 4 options and lights blink, when the washing and drying cycles are complete. I would recommend the Maytag, Model #MDB4949SHBO wholeheartedly.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

I bought a Maytag MDB7809AWW2 dishwasher two years ago. The control panel just started doing free-games. Lights would come on and off during the cleaning cycle. When selecting a cleaning cycle, some functions would be automatically selected without the capability to deselect them. It is our second and last Maytag dishwasher. Stay away from them!

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

Maytag XL Washer - My new machine is awful as well. Black clothes are smeared with I dont know what... looks like dirt. The wrinkle cycle doesnt work and the bedding cycle forget. Wish I read reviews... silly me.

I moved into an apartment home in June 2016. My apartment was furnished with all new appliances. The washer & dryer were purchased in May 2016. I live alone so on average I do 1 load of laundry per week. In November I noticed paint peeling on the inside of the dryer drum. Each time I use the dryer more paint peels. I contacted Maytag because I figured the dryer was still under some type of warranty. They sent out a technician only to tell me this was a cosmetic problem and cosmetic problems are not covered under the 10 year warranty. I would need an authorization code from Maytag if it was covered under warranty.Again, I contacted Maytag and now they want to send another technician for a second opinion. I dont feel this is cosmetic because the dryer is only 6 months old and already the paint is peeling. I feel this is a product defect because this type of problem shouldnt happen on a new appliance. I have scheduled an appointment for a second opinion and if he says its cosmetic then I have to pay out of pocket for the repairs to fix the problem. I thought Maytag stood by their product and customer satisfaction was a top priority. I guess I was wrong.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

My $1500 2 yr old Maytag mbf2258Dem refrigerator stopped cooling properly (wont freeze). The icemaker was the slowest I have ever had. That may have been the problem when I bought it. The Maytag Repairman came out and said that even with Maytag sending me a new compressor (under warranty) this unit was not worth fixing. I called Maytag and they said sorry there was nothing they would do. So l looked up every review I could find... and this refrigerator is just bad. Not Worth Fixing. So Maytag deceived me. On the front of the door it says 10 year compressor warranty. Thats a big sales feature! They know that they have a problem. This is one bad company!

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

I had a Maytag dishwasher that I purchased around 2005. I had no issues with it at all. Then, I got a notice that it was being recalled due to a fire hazard. My options were to either get a repairman to come out and fix it, or get a credit towards a purchase of a new dishwasher. I chose the second option. Even after getting a credit, the purchase cost was way more than my original dishwasher. I purchased the new dishwasher in June of 2010. Last spring (May 2012), I noticed a gap in my hardwood floors around the sink. A flooring rep looked around and said he would bet that theres a leak either at the sink or the dishwasher. I took off the front kick-plate to the dishwasher and discovered a wet spot. I monitored that area and discovered the leak coming from under the dishwasher (around the float switch). It wouldnt leak all the time, but every now and then, it would leak half to a full cup of water. I had the hardwood floor fixed (cost $350). At the same time, I schedule a service repair through Maytag. They sent a rep from a local repair company (Convenient Appliance Service, Inc.). The service rep couldnt identify the cause of the leak but said it was more than likely the seal around the door. So, I paid another $160 to get the repair done. I monitored the leak for a week and had no problems, so I put the kick-plate back on. In September 2012, I noticed a wet spot in front of the dishwasher. I took off the kick-plate and discovered that the dishwasher was leaking again. This time the leak was worse. It would leak 1 to 2 cups of water during a wash cycle. I called the repair company and they came out free of charge to take a look at it. The service rep said the float switch had gunk build up in it. He cleaned it out and said that should fix the problem. I monitored the area for 2 weeks and everything seemed to be fine. Last week (March 2013), I noticed some gaps in the hardwood flooring around the sink and dishwasher. I pulled off the kick-plate and discovered a wet spot. I ran the dishwasher and discovered that it leaked a ton of water (over 4 cups). I contacted the repair company that came out last time, and they said they would have to charge me $100 plus to come out and take a look at the problem. The rep recommended contacting Maytag. I contacted Maytag and they said I would either have to pay $129 for a service call (not including cost for parts), or $269 to get covered under their Repair Plus 1 program (everythings covered and it adds 1 year of warranty my dishwasher). I asked at what point Maytag would replace a dishwasher. The rep said when it is deemed unfixable. Other than that, they just keep coming out if I have issues. Part of me thought I need to cut my losses and just rip out the dishwasher and get a new one (cost somewhere around $700). But I went with the Repair Plus 1 program in hopes that they can resolve the issue. But Im definitely going to have to get the hardwoods ripped out again. It looks worse than before. It’s probably going to run another $500.

My husband purchased the Maytag Bravo December 2013. We immediately started noticing clothes been destroyed and stains still in clothes. We immediately contacted Whirlpool and shared our concerns and they sent out technician. He stated that the motherboard was gone. After repairing the motherboard, that do not stop our clothes from being destroyed and making them clean. I have wrote numerous letter to the CEO of whirlpool and sent pictures. When they decide to call you back months have passed and still they do not want to help you. Whirlpool have refused to take responsibility for a bad product they invented. They do not stand by their mission. Someone please help the consumer, because this big corporation refuse.

I ordered my dream refrigerator (Maytag Model MFT2776FEZ) on 05-12-2017. I had to wait 4 weeks for it to arrive because it was on back-order. I was willing to wait. All was good for 6 months. January 2018, the six month old refrigerator quit cooling. It took 2 1/2 from the service call until the part came in to fix before I could use my refrigerator again. I lost all my food. The same thing happened again in March 2018 except that it took 4 weeks for the part to come in once the serviceman ordered it. I lost all my food for a second time. February 2019, the same thing happened again. I placed the service call on 01-31-2019 for service, but the tech could not come out until 2/6/19. The part had to be ordered and could not be installed until 2-28-2019. For the 3rd time, Ive lost my food. My best friend that has appliances that are nearly 30 years old. She was going to replace all of hers and get exactly what I ordered. She has changed her mind and has decided she would rather keep her outdated appliances because they work.

I love the way it can really handle large loads. The dryer is the best though. It actually dries your load without you having to turn it on more. There are many different choices that handle drying. So, no more to the bone drying.

Maytag Bravo model MVWB750WQO. Bought this washer in 2009 for 1300 thinking it would last at least 10 years! Wrong! I loved it until a few months ago when it started making VERY LOUD noises during final spins. Sounded like the house was going to take off. Then today it started leaking water. Repairman said it needed a drum, seal and gasket. Would have cost 700-800 to fix. Needless to say we bought a new washer today, and it wasnt a Maytag!! For that much money I was expecting the washer to last a long time!

Have had it for 2 years now and its leaked out the bottom since it was 6 mos. old. Now the ice maker has fried a motor and were having to repair it already. Cant believe we spent a small fortune on this fridge and are having constant problems with it.

We were delighted with our new Maytag refrigerator, model #MBF2258XEB, until the compressor died less than a year after we bought it. Home Depot, where we purchased it, directed us to the A&E Company for service. Two weeks later, we are still without refrigeration; Maytag refuses to replace it and even refused to overnight the new compressor. We thought Maytag set an industry standard for excellence. Don’t buy this product if you want a reliable refrigerator from a company that stands behind its products.

Our new refrigerator was pissing all over the kitchen floor. We had to disconnect the ice maker after an alleged repair part was supplied. (We had to pay a plumber to install it.) It didnt work, so we finally had to disconnect all the parts related to the ice maker. Here it is July, and ice cubes would really be appreciated right now. I get angry when I see all the Maytag commercials that pop up on the internet!

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

I bought my Maytag Refrigerator about 7 years ago and the night mares have not stopped. The ice maker has broken down so many times, I forgot to count. The drip from the ice maker lands on the floor of the freezer and drips out to the floor. The cold part of refrigerator end up freezing the fruits and veggie and milk.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

I bought this machine a year and a half ago. The entire drum and spin motor need to be replaced. Maytags warranty only lasted 1 year. I bought it at Home Depot, and also purchased the extended 5 year warranty. The extended warranty is as bad as the washing machine. I am now just 2 days shy of 4 weeks of trying to deal with both parties. Ive had to take my laundry in to have it done. The cost of the laundry, the cost of the machine, and the cost of the warranty is more than $200 more than what Home Depots Extended Protection Plan is willing to reimburse/refund. Home Depot does as much as Maytag when it comes to standing behind what they sell. An $800 washing machine only good for 18 months, really???

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.

I purchased this dishwasher at least 12 years ago and it still works. However, after that much use some of the buttons no longer work. It has china, economy, regular, rinse only and extreme wash features.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

Maytag Bravos XL - I purchased my maytag washer & gas dryer on 5/12/12. In Dec 2012 the heating element went out. I had to wait a week for a repairman to come out on Dec. 20 to fix it. Now for the second time on Dec. 30th, 2014 the heating element has gone out. I called for a repairman to come out. I have to wait until Jan. 12th 2015 for service. I have 8 people in my home including 3 grandchildren. This length of waiting is ridiculous and very inconvenient.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

I bought a Maytag refrigerator model MBB1953XEW three weeks ago. According to its features on the Maytag website, its supposed to be quiet (QuietSeries 100 sound package). Ha ha, make me laugh. Its the noisiest refrigerator Ive ever had. The repair guy checked it out this morning. He spent about 5 minutes running some sort of test with the help of his iPad. He then told me everything was perfectly alright, the noise was normal for a Maytag, and that I was going to get used to it.Needless to say, he had a totally condescending attitude. Its the first time I ever bought a Maytag. Previously, I had a General Electric that was noisy but not as much as the new Maytag. Prior to that, I had a good old Kenmore that was perfectly alright but that I had to give away for other reasons. This time I chose Maytag because I thought it was good quality and I wanted it to be very quiet. Well, nope. Next time, for sure, it wont be a Maytag.

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

Maytag AquaLift Oven #YMER8880BW - The aqualift technology does not clean the oven. It is sorely inadequate. I bought Maytag because of its reputation. This range should be recalled as should all their ranges with this useless technology. Buyers BEWARE! Do not purchase any range from Maytag which advertises Aqua Lift technology. This purchase has soured your reputation Maytag. I also purchased a fridge with the stove. I will NEVER buy a Maytag product again. I also would like to ask frustrated and disenchanted readers how they are getting their ovens cleaned. What product(s) can be used. Maytag - complete FAIL!!

I should have returned this machine after my first load of wash; it ruined a couple articles of clothing. Later it ripped a throw rug and just recently ruined a drapery panel. Is there any way I can exchange this machine and rid myself of it? SN: C22534900 Model: MVWC400XW4

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

I purchased the Maytag Bravo Series in August 2010. Two weeks ago, I had to replace the idler pulley on the dryer which was no easy task. Now today I was washing a load of clothes only to walk into my utility room and find it flooded. This didnt even start out as a small leak so at least you would have a warning. On the spin cycle, the washer is making a clanging sound. These were not cheap models. I paid $1600 for the set. I will never buy another Maytag product especially after reading all the complaints that people have had about this series. Why hasnt something been done to protect the consumer? I did not purchase the extended warranty as I thought Maytag sold a good product. I owned another set of Maytags that were almost 30 years old when we got rid of them and did minimal repairs over the years. We are only a household of 3. It is not like these appliances are overloaded or abused. Its very disheartening. In this economy, most dont have money to just throw away and that is what I feel like I did!

I have never given anything a negative review before, but this, by far, the absolute worst appliance I’ve ever had in my entire life. I bought it because I had an old leaky washer, but I’d take it back in a heartbeat because it could ACTUALLY wash my clothes. We spent a lot of money on this washer because we wanted something really nice that would actually work, but this washer is no better than me throwing my clothes in the sink and turning the water on. I’ve tried every kind of detergent and pretreatment that I could possibly try, and nothing helped because the actual machine don’t do nothing. Shirts come out still coated in mud, and half the load is dry??? Please, save your money, get your washer somewhere else. And I hate to even give this thing 1 star because it ain’t even worth that.

We bought a Maytag dryer and within two years the drum cracked. It will cost over $500 to repair it and then will the new drum be better? I bet not. Piece of junk.

Have had nothing but trouble with this fridge! Ice forms at bottom of freezer with frost all over top shelf. Ice maker no longer works. 3 years old for goodness sake. Had repairman replaced all lines, and still have the problem. Heard you have to unplug fridge for 24 hours to solve problem EVERY 2 Months! I Guess the Maytag repairman stays lonely because they dont stand behind their product! Hate it!!

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

This set is a GREAT ONE! I love my HQ washer and dryer. The washer has so many settings to choose from for all different loads of clothes. It washes and spins everything great. My dryer is so nice! I can dry a load of whites: towels, washcloths, hand towels etc in record amount of time. I would highly recommend them both.

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...

I purchased a refrigerator in Aug. 2012 from Home Depot. In June 2013, it broke. I contacted Maytag/Whirlpool and they had three companies come out to try and fix it over a four-week period when finally it was determined that it was unrepairable. Now I was told that we can get an exchange but now they have the incorrect delivery address and the person supposed to be handling my case has been on vacation and I left several messages. I contacted Maytag for someone else to help and cant seem to get anyone for the past 2 weeks. This has cost me money for food lost, time from work and time making calls.

JADE model RJRS4270. Had this model for 10 years with more than 10 service calls. Always breaking down and Whirlpool will not honor the warranty. Paid for an extended warranty service to Maytag/Whirlpool offered by the manufacturer. When unit broke Whirlpools warranty service provider Assurance said Whirlpool no longer provides the parts needed, sorry can’t honor the extended warranty you had paid for, no parts, and no refund. The evaporator drip tray had been replaced three times. Asked to have the unit replaced. Whirlpool was absolutely disrespectful and only offered me to the option to buy another discounted $8K unit for a with ~ $2K discount.So far approx. $6K unit + approx. $1K extended warranty (not honored) + approx. $1K parts and service out of my pocket (Whirlpool continued to tell me it was not warranted). Although the operator’s manual said it was covered. While under warranty Whirlpool doesnt have replacement parts to service it. Multiple service tech are telling me there are many known issues with this unit. Found out there’s class action law for the same issues Im experiencing. Whirlpool only offered a new unit at approx. $6K. So total for me to date if I choose to take the discounted unit would be $12K. Dont buy this unless you have a good lawyer. Hardly seems reasonable. Extraordinary time/money loss and aggravation.Bought 8/1/05 S/N ** Model RJRS4270C $5,400. Service call 5/10/06 Repair - Freezer dripping water and pooling on floor. Service call 6/28/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/5/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/12/06 Repair - Unit not defrosting. Service call 8/26/06 Repair - Freezer not cooling, ice backup, fan burn out, drip tray. Service call 9/2/06 Repair - Evaporator fan not working. Replaced unit 9/_/06 S/N ** Model RJRS4270D. Maytag Dependability Plus Cert No. ** $99.00 8/02/08 thru 8/02/11. Maytag Extended Service Plan Plan No. ** $297.19 9/02/09 thru 9/01/12. Maytag Extended Service Plan Plan No. ** $405.31 9/01/12 thru 9/01/2015. Service call 10/13/10 Repair - Ice build up in fan, freezer not working. Service call 10/20/10 Repair - Installed new drip pan, bi metal, fan motor. Service call ~ 8/_/15 Repair - Service tech states, Whirlpool no longer has parts. Even though we paid hundreds to have a still active Maytag contract extended warranty. Whirlpool outsourced service to third party. Service call ~8/_/15 Service tech refuses to repair because cant get parts from Whirlpool. Asked me to find part on eBay or some other source so he could repair since Whirlpool could not provide. Got part. He did fix. Freezer stopped working 4/2/16. Customer support 4/3/16 followed owners manual instructions for warranty and call number, Whirlpool said theres no warranty and to call any local service tech. (Owners manual said compressor was still under warranty). Service call 4/4/16. Tech refused to work this Whirlpool unit, believes to be issue with the compressor leaking or system blockage or bad valve in compressor. Customer support call back - Krisi, was warranted. Jade Specialty Department. Customer support call back - Jared, no warranty, sorry. Explained contract to him. Nope/Nada. Customer support transfer - Jan, yes was warranted. Asked to speak to manager/sup. Said if you won’t honor warranty then please provide replacement. Transfer to Mike said we must schedule service through Whirlpool to fix contradicts. We asked for reference number to track. Mike said they don’t use reference numbers (contradicts Jared from when he asked me for a reference number). Two days no call from Whirlpool. Customer support call back 4/7/16 - Kari, offered small discount for equivalent new or refurbished unit $5,739 for Model KBSN602ESS. Said although under warranty, Whirlpool may not be able to provide parts to repair unit, but they will sell me an equivalent unit.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Freezer leaks water all over the kitchen floor in front of this $1900 piece of garbage. My husband disconnected the water line (for in-door water and ice cube dispenser) and it STILL leaks water. I can vaguely remember a time when the purchase of a refrigerator (manufactured in the USA) wasnt necessary more than once or twice in the average persons lifetime. This Maytag refrigerator is our second french door fridge in 5 years. The last one was an LG that had a shoddily designed and manufactured compressor that sounded like a diesel engine idling in our kitchen. Of the two, this one is equally defective but doesnt wake the dead when the compressor starts.It has become glaringly apparent the Chinese practice something I refer to as Cargo Cult manufacturing. Google Cargo Cult and youll understand what I mean. Briefly, they manufacture products that APPEAR to be refrigerators, washing machines, ranges, etc. However, lack of quality control and zero competition from companies that provide a well-made, quality product that lasts more than a year or two allows and encourages these slobs to continue pumping out what appear to be appliances until the consumer plugs them in. Thats when the fun begins.

This Bravos washer and dryer saves energy for sure, but sadly, that is it. It does not wash my clothes and rinse them adequately. They are so twisted and wrinkled I have ironed just about all my clothes. Even my synthetics are severely wrinkled. The dryer sensors do not work. They never dry the clothes adequately. The concept was good in that they are compact and have a large capacity, but the design does not work. I was lured in and unfortunately, there were no reviews at the time but I see that everyone shares my sentiments. The washer and dryer are just not any good. Thank you.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

I had to rate at least a one star because there isn’t a negative to rate. We bought the Maytag mvwb955fc1. First off it doesn’t clean our clothes. I can not get stains out or whites bright. I don’t feel it uses enough water. I put a full load in and it only fills up less than half with water. I try half loads and still not clean. It’s always shutting off when I wash sheets. Indicating it’s off balance. Today I started it before work and the lid exploded. I don’t think I want to even replace it at all. This could have seriously hurt someone. Do not buy this washing machine. The dryer is great so far. I wish I could post a photo to show you all.

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

After the waranty ran out, oven failed to ignite. Called repairman who couldnt diagnose problem. Broiler works. Replaced some kind of wire & part for $350. Good for 6 months. Happening again. Paid a lot for this oven.

The washer doesn’t have enough water to to get clothes clean. Even on deep water wash there’s is not enough water. It doesn’t get clothes clean, its very noisy. It takes a long time to was, even on short cycles. You can’t soak dirty clothes, it has a cycle for soak but it is not long enough. After about 3 months the lid licking doesn’t work and the progress lights remain on and never go off. This is the worst washer that I have ever owned. I just want to return it and get a different one!

I have a Maytag washer that I bought new in 1995! It is still washing my clothes like a champ. It must be true - the Maytag repairman is a lonely soul, in all these years I have never had to call him!

We bought top load washer model # MVWC425BW1 at Lowes brand new 9/22/14 for $493.93. On 11/23/2017 it stopped working and would not even come on after lid locked. Found out it needed new parts that would cost us over $300 to fix and we could buy another new washer for $400. We are very disappointed that this washer with only two people only worked three years when we thought we had bought a reliable product that would last. Sent several messages in November but no response till today 12/13/17 after filing. BBB complaint filed and they decline to do anything. So this company just wants to sell products but has no customer service. They only give a year warranty. Of course if the product is not going to last they want you to buy more.

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

We purchased Maytag microwave (MMV4205DH1) less than two years ago. Within the first year, the microwave would not work and we would see an Open and Close Door message. We had it repaired and now 10 months later it is doing the same thing. The cost of repairs is high--the same as a new microwave. We have been inconvenienced throughout the holidays by our broken appliance. Disappointed.

After using my GE Profile to death we replaced it with a Maytag; mostly for the cost. Although I hate to admit this, remember the old saying you get what you paid for - Well its true at least in the case of this Maytag oven. I am a constant cook and own a bakery, I often bake many of my products at home. Since getting this oven I have had nothing but failures. The cakes are over done, underdone, cookies burnt, not cooked enough; my time frame for recipes is so off! I wrote a cook book and have baked for years so I know for a fact its not some miraculous mishap that all of a sudden I cant bake. Ive had them come calibrate the oven but still no success.Im going to call them again but I felt compelled to let people know this is the worst oven in history and avoid purchasing it at all cost. I plan on having the service team come out one last time but if this doesnt work I plan on replacing it. Its a Maytag Double Wall Oven-Top Convection-Self Cleaning model no: MEW9630DS-SS. BUYERS BEWARE!

I bought a Maytag dishwasher just 15 months ago. Worked fine for the first 12 months. Then literally, a few short weeks after the warranty expired, the buttons on the control panel started acting up. The normal button, when pushed, would light up the delay hours. The light cycle would make the rinse only come to life. It was beyond frustrating. My husband would unplug it to reset it and that worked for two weeks but now, nothing. It wont work at all. Im FURIOUS, considering we spent $450 on this thing and now its useless. I had a Kitchen-Aid that I loved but due to cost, decided to get this hunk of junk. I learned my lesson..Maytag, you should be ashamed you make such horrible products.

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

I purchased my Maytag washer and dryer set from the Maytag store in Glendale, AZ in September 2005. I even bought the stands for them. With my purchase, I got the extended warranty for four more years. I didnt realize that I would really need it. I have had so many issues with the washer and dryer I cant even count - from the control panel not working, to the noise and the vibration when washing, or maybe in the smell of moldy cheese. I also have issues with the constant chimes of D5 code that keeps coming up on the display screen. After 2009, I finally gave up on calling the Maytag customer service folks to have someone come and service the washer because it was out of warranty. I just decided to live with all those issues.As far as my dryer goes, the rollers went bad and that was replaced. The burnt smell isnt so bad as long as you use a wire hanger with a sock on the end of it and clean the inside of the vent. Then try to vacuum it, take the sock, get it wet, and clean the inside of the vent again. This was the most expensive piece of junk I have ever purchased in my life (almost $3,000.00 with the stands and warranty).What really gets me upset is I had the Maytag people servicing my washer and dryer up until 2009 and no one told me about a recall of my washer and dryer. The only reason I found out about it was searching for the specs as the washer finally died and I am replacing it. Trust me. I will not be purchasing a Maytag. I know that Whirlpool purchased Maytag so I am not even going to consider Whirlpool either. Since Whirlpool purchased Maytag, Whirlpool should have contacted all Maytag consumers, (which they didnt), put ads in newspapers (which I did not see) or put an ad on TV. None of these appeared to have happened.By the way, when I bought my Maytag appliances, I was supposed to get a $200 rebate for buying the stands that never came. It must have gotten lost in the mail - as well as the Tide coupons for three years. You, guys, remember that too. I will never ever purchase a Maytag appliance or Whirlpool, since they own Maytag now.

I purchased my Maytag Refrigerator in Feb 2013. It is model MFF2558VEW7. It has the French doors w/ freezer at the bottom. This past week, I lost everything in the freezer. I call the Home Depot where I purchased it and they said that I have to call Maytag. I did and they sent a repairman out. It needed a compressor. After only 8 months, the compressor goes out? Why should this fridge be repaired and I not be given a new one? With all the problems with the Maytag, there needs to be one big class action filed. I asked for a loaner because it would take up to five work days for them to order the part. The answer was, We do not provide loaners.

Bought Maytag dishwasher 2007 at Lowes. Model mdbtt60aww-37837606ll manufactured in Benton harbor, Michigan. First got a recall that something was faulty, could cause fire, needed replacement. Took 2/3 weeks to get repaired. So couldnt use. Never quite cleaned good - many times had to rewash silverware, glasses. Never took off food unless very well rinsed. Today the control panel went. Called a local repair he said, Dont even fix. Toss and get a new one because its too costly to repair. I asked what should I get. He said no GE, they are getting out of appliances, no Samsung. Hes got whirlpool so guess Ill give that a try. In the past Ive had dishwashers 20 years, appliances 20 years. This junk lasts a year or two. Plastic cracks. None of these appliances are great anymore. Doesnt matter who you buy. Someone needs to get some quality control on what these companies are peddling .

I called Maytags customer service about an over the range microwave that was bought 2 years ago and barely used. The mechanism in the microwave on the latch for the door, clicked into the body of the unit and therefore the door does not register closed which doesnt allow it to come on. After explaining this issue to the customer service rep, she insisted that the only thing that Maytag would stand behind was the part if needed. A service call would be between $100 - $150. The microwave isnt even that old and why would Maytag not stand behind a like new unit? I bought 3 Maytag products and I am now regretting it. I had asked to speak to a supervisor and she just proceeded to repeat the same thing the sales rep did. They will only cover the cheap part if needed.What happened to Maytag being top of the line? Apparently they dont care about standing behind their products and would rather you buy an expensive extended warranty to cover their cheaply made appliance. I think they should be under review as a company. I would somewhat understand paying if my appliance was 5 to 10 years old. But its basically new. How is there no protection for customers when it comes to purchasing lemons from an appliance dealer? I will NEVER buy Maytag again and plan on selling my 2 other newly purchased appliances before they have issues. Maytags reviews on social media are terrible. All they offer are the words Im sorry and I understand your frustration. I assume thats just what they have written down in front of them to tell everyone who calls with issues. How do you not stand behind your products! I wish I could select no stars vs the 1.

Maytag calls peeling paint a cosmetic issue. With a convection oven it could be a toxicity issue. Waiting for an answer to my question as the fan blows the peeling paint onto anything that is not covered. Dont put foil on the bottom as this compromises the paint due to design. Truly sorry to have purchased Maytag as this line is not the Maytag we grew up with! Old school ovens and products had the quality or workmanship to last.

The Maytag Centennial (Model MVWC6ESWW1) washer was purchased in September 2009 and within 18 months no longer provided water at the temperature selected on the control panel. The problem started after we used a spin setting to remove water from a cycle that did not complete itself. Somehow selecting a spin cycle disturbed the water temperature control mechanism. We were advised by Sears to unplug and then reattach the electrical connection (similar to rebooting a computer), but this was not successful in water being delivered to the washer at the temperature indicated on the control panel. While there was minor damage to clothing and a waste of hot water before we realized what was happening, the real inconvenience is not being able to rely on the water temperature setting. Based upon reading comments on the internet (including Consumer Reports) concerning this washer, the public should be warned not to purchase this machine. Better still the machine needs to be recalled in order to protect the consumer.

We purchased a washing machine, top loading washer model MVWC415EW1 on 9/2/2015 and the machine did not work right. 11/2/2015 is stopped working all together. It will not wash the clothes. The repair man says we need a new cold water valve. Maytag says it does not have the part to fix the machine. Period. Now we have a new machine with a 10 year warranty which does us no good as Maytag does not have the parts to fix. So it is back to a laundry mat until we can save enough to buy a new machine from anyone but Maytag .

Bought a nice looking Maytag fridge 2 years ago. For the past 6 months it has been leaking all over the kitchen floor. Most recently it has started leaking every 2 days. It is so frustrating as well as extremely dangerous! Both my younger kids have slipped and fell because of the slippery floor. We now have to keep a towel there all the time.Please let me know if there is a product recall. Not the Maytag we used to have. My parents bought all their Maytag appliances when they got married and they lasted over 30 years! This is why I bought the Maytag fridge... not sure of the quality now.

Bought a Maytag refrigerator model #MFT2673BEW10 in 2013 for $2100, the ice maker has leaked for two years. Paid for service come out and look at it, ice maker is shot, three years old, and it is junk. Tried to get help from Maytag Customer Support, what a joke. I was hung up on 4 times, and never did get any type of help except your unit is out of warranty. Bought at the Maytag Store in Saginaw, Michigan. No help there either. DONT BUY MAYTAG!!! They are junk!!!!

DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level not correct, binding laundry together and replaced the same parts with cheap parts over and over... just wanted clean clothes in a no frills washer. NOT with this washer. Owned it 3 yrs and disliked it the first half washed load... $869.00 heap of junk.

My washer is 3 years old, it sounds as though an earthquake is rocking my laundry room during the addition of water, rinse, and spin cycles. Cleanliness only when washed twice, along with the washer stopping at 12 minutes because of UL signal (unbalanced) - this happens even when I have a small load. The dryer does dry clothes however along with tons of Lint stuck to my clothes. I empty the lint screen after EVERY dry cycle. Have had repairman who charged me $70.00 and said he could not fix the washer.

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

My clothes sometimes come with white spots on them. My clothes are very twisted. I would LOVE to have Maytag replace my washing machine so I could again sing their praises!!!

Washer was delivered Feb 2016. (First one delivered Jan 2016 with damage.) Home Depot HEAVILY promoted this model - we paid $600+. This washer has NEVER thoroughly cleaned clothes & now does not drain completely!!! Theres always lines of dirt left on clothes - you can see dirt clearly on dark clothes. Washer does NOT fill with enough water to thoroughly wet clothes! (Even on the bedding, extra dirty settings!) Clothes smell clean because the detergent was not washed or rinsed out. Washer does not agitate, turn over or rotate clothes... It gently shakes the tub side-to-side (like a mild earthquake does the ground) which does NOT move clothes around. Home Depot salesman said it strongly rocks clothes turning them around and under. It does not do that! You have to stop washer and PHYSICALLY move clothes from center and turn them around so bottom of pile gets wet (Now I understand why this model has a see-through lid!!!) This model is supposed to pre-wash sense the load amount by shaking the tub side-to-side to gauge how much water is need - FALSE ADVERTISING! I put gallons of water in two loads (same bulk & weight of clothes) to see if more water would be used on the heavier load - results: the same amount of water was used on both loads. Now (Oct 2016) the washer is not draining completely and going back to wash instead of rinse, drain! Maytag Corporation just says theyll send a repair person out but this is a SMALL town & the repair shops theyll use here are sketchy!This Washer is a huge waste of money just to own laundry status tone bells & non-usable settings. Its probably in violation of OSHA health/safety codes because if there are chemicals, feces (sorry, but wheres theres kids...), blood, diseases (if you visit anyone in a hospital), etc on the clothes... Those things are NOT being washed out of the clothes, so youre being infected by touching improperly washed clothes. WHY is there not a RECALL for this appliance? There are many, many people having the SAME problems as us. This is our first HE top-loader and I wish I could afford to get rid of this & buy a washer with an agitator... But alas, we still owe $300 on this worthless (albeit fancy-looking) appliance. :( Maytag XL HE top load Washer MVWB835DW (Does NOT clean clothes!)

Maytag washer MHW5500FW had service just a month after purchase and still a year later the washer has problems spinning using direct drive. Even a few towels are soaked when cycle is done or errors out and must be restarted. Most of the time the washer has to be cycled on spin to remove water from soaked items, not just a simple bath rug, towels, bed sheets. Almost anything has a problem spinning. Had to purchase another year of service coverage as I dont trust the washer will last. Soap dispenser needs to be diluted despite using correct soap, per service tech advice which triggers sensors to shut down. Machine looks good but not ergonomically designed without the stand as you can easily lean over the washer and turn on and off accidentally. Same goes for the matching dryer, also can easily set off the on pause and on/off button. Dryer works great other than that.

I purchased a 2006 model Maytag Top load Washer and Dryer used 9 years ago January 2010 to replace a 2009 Samsung front load washer/dryer. I had to replace the agitator on Maytag washing machine before I could use it. Fast forward November 2018 the washing machine stopped agitating the clothes, but would spin the water out. I replaced 2 belts and thoroughly cleaned underneath and inside washer to remove soap residue. Maytag washing machine has been used twice a week since 2010-2019 and still going strong. Maytag dryer has never had any issues. I also own a set of 25+ year old Maytag Washer/Dryer both still working.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

Perfectly great, cleans anything, not terribly quiet, but results are more than satisfactory. Good water pressure, cleans every nook and cranny, things come out spotless. I do not have anything else to compare, but I think the size is fine, I can put a lot of stuff in it. Controls in front at top, easy to use, clean appearance. Even though my dishwasher is 13 years old, I have not had any trouble with it. The top racks are strong and hold a good bit of glasses, cups and bowls. I have put baking pans, cookware, grates, and a lot of other stuff in to wash and it all came out clean.

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

Paid $900 for this side by side stainless steel model 15 years ago. Pros: performance, appearance, simplicity. Cons: none. Only 1 minor repair, and the repairman said this is 1 of only 2 makes he recommends.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!