I purchased this dishwasher from Sears in July of 2013. Barely 3 years ago. The last few months the controls have been acting odd. The control lock would automatically just turn on at odd times. Yesterday when I hit normal cycle it went to a different cycle and had many other options lit. It would not start. Finally it went dark, no lights, no nothing. I see many people have had these types of issues with this type of Maytag dishwasher. Disappointing. A dishwasher should last longer than 3 years. Sears said they would send a repairman out but it would have been minimum $200 after it was all said and done. Id rather own a non-Maytag dishwasher so we went and bought a different brand.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.

I hate my new Maytag washer and wish I had never purchased it. Theres no way to control the water level in it, and on sensor mode, the clothes are barely wet and rubbing against each other creating wear. Things come out with soap stains and twisted up so tight that I dont believe water got close enough to the dirt to carry it away. Dont waste your money.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

My washing machine is a Maytag Ive been using for over 27 yrs. I love the older, top loading machines because I like to take certain items out after 5 or less minutes. I now live in an apartment & wont use their machines! Thinking about a stackable for my personal use. I am quite fanatic about laundry & do a lot of items by hand.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

In October of 2012 we bought a Maytag Refrigerator Model MFF2258VEM. In the spring and summer of 2014, we noticed puddling on our kitchen floor. We thought it was our dishwasher or sink since the $1800+ fridge was new, but couldnt find the problem. We travel a lot and are gone for extended periods. When we returned in winter of 2014, we discovered that there was substantial puddling and found a sheet of ice in the bottom of the freezer compartment. We did research and found that this is a common problem with all the bottom-freezer Maytag models, which then leak. We discovered that the leak had seeped into our kitchen sub-floor and was destroying all of our kitchen floor tile, causing cracking and breaking, a renovation of just a few years previous that cost a lot of money. There was NO problem with the floor until we put in this Maytag refrigerator. The remedy for the leaking is constant maintenance and a lot of work, totally ridiculous for a product that costs so much. I want to sue Maytag for both replacement of the refrigerator and the cost of replacement of my tile floor. Can someone please advise? Thank you.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

I am PISSED off at Maytag products in general. First I buy a washer and dryer from a Maytag store-buy a 12 year warranty. Call in for repairs - Maytag and A & E say I have no coverage. Now I am getting bills to pay for coverage on both because the form says my coverage ends this December 2011. I buy a Maytag dishwasher and its the one that catches fire. I get the rebate of 250 for buying the more expensive one - but am still out 500 dollars. Installation was bad by contractors from Lowes - just called that in to have it reinstalled. AND THE MOST RECENT IS THE FRENCH DOOR REFRIGERATOR I BOUGHT 9/4/2010. IT STARTED ACTING UP AROUND CHRISTMAS TIME - WEIRD NOISES, WOULDNT MAKE ICE - I AM SO BUSY WITH MY MOM I DONT CALL IT IN UNTIL JUN 25TH AND THE REPAIR PERSON SAYS IT IS UNREPAIRABLE AND HAS INTERNAL DAMAGE TO THE WIRES.

Loading is easy, operation is extremely quiet, dishes are very clean even on normal auto wash cycle. White, integrated depress buttons, full size, removable utensil baskets, upper and lower racks, top rack is manually adjustable, stainless steel tub. White front which is what we want not the ugly old metal stainless steel, usage buttons are on the upward facing edge of the door, pull down handle is nice size and very sturdy. Model is MDB8959SBW3. Even on normal auto wash cycle dishes are clean without much pre-rinsing. Purchased 10/14 from local dealer and professionally installed. So far we love it.

We purchased a Maytag dishwasher (model mdb4709aww1) from our local appliance store. A little over one year after purchase, the control panel (part w10254834) stopped working. Our appliance store replaced it. They charged us for the part but not for a service call. Its been two years since the new control panel was replaced and it just stopped working. Now, we have to pay $275.00 for the new part and service call. My previous dishwasher lasted twenty years and we never had a problem. I thought Maytag was a quality product. Sadly mistaken!!

Maytag junk MFW2055FRZ00. We had to replace our reliable 15 year old Frigidaire side by side fridge when it failed due to a compressor failure. We should have pressed the service company to replace it or found someone who would. We were limited in replacement units because of built in cabinets, thus a smaller French door (so we have to open two doors rather than one) Maytag. Perhaps our 30 year old Maytag washer and dryer made us believe Maytag still offers high quality products. We were wrong. Everything about the unit is poorly designed, cheap and flimsy. The freezer drawer pulls out unevenly and the ice maker is primitive. Above all no matter what appliance you choose be sure there exist factory authorized servicers in your area otherwise warranty issues are a problem.

I bought Bravos xl. I hate it! Everything about it. It does not get my clothes clean and it ties load in knots therefore being off balance constantly.

I bought my Maytag Centennial washer & dryer about 2 yrs ago. It wasnt long after I bought the set, that the washer started having problems. I noticed the button to turn it on wouldnt go off. Then it was a pain in the ** to not be able to open the lid while the water was filling up. Something I havent noticed until today, its suppose to fill up to the amount of clothes that is in the washing machine. Well when I opened the lid there wasnt enough water in there to even cover all the clothes. Now I know why my clothes are not coming out clean!!! I am so frustrated with this machine and the company!!! DO NOT BUY THIS PRODUCT!!!!!

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

French door always has freezer closing problems. Whenever the freezer is not closed tight, the bottom will form ice block, and freezer doesnt close. I have extended warranty but the repair people do not give quick appointment. I sick of this product.

Topload Maytag Bravos washer sounds like a jet on spin cycle. Called Maytag, no recalls or service issues. Just wanted to sell me a service contract for over 300.00 dollars that would fix it and be covered under warranty for a year on anything that went wrong. Could set me up with a service call, but it was six days from now - no thanks. The washer this replaced was a Sears which was 26 years old. It still worked and I sold it for 75.00 dollars. Guess I will stick with Sears!

Four years ago we upgraded our 20+ year old Maytag washer and dryer to go with a more water efficient model. The old units were working like champs so we upgraded with Maytag assuming it to be equal quality. From the beginning we were not pleased with the washers cleaning ability and now we have electrical problems and a leaking transmission. Our serviceman estimated repairs to be the cost of a new washer. (Im not talking about a Maytag for replacement.) I e-mailed the Maytag company and they basically said Too Bad. Totally disappointed!! Wish we had our old units back.

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

I mistakenly purchased the Bravo XL top load washer. I only wish I could give it a zero rating. I have only tried to wash 3 loads of clothes. It is almost beyond belief that anyone could possibly think this could clean anything. My husband actually watched it “work”, and insists I call Maytag because they must have forgot a part! It does nothing but crumple/wad the middle items together and rub them...and only them...together. There is no movement of the outer items until it spins. Maybe Maytag should enlist people who actually do laundry to “test” the items they put their brand on. I know the government and the energy rules have added to the complex problem of buying something as simple as a washing machine...but this piece of junk is almost laughable to watch as it destroys your laundry. I’m almost embarrassed to let anyone know I bought it. Thankfully, I have 30 days in which to return it.

Bought new and only had one service call in 20 years. The control panel was replaced. Since then, the dishwasher has performed well and, factually, was far less expensive than many other models! That figured in our decision when remodeling our kitchen back then.

I got a washer from a Menards Store in Fond du Lac, WI. I was given a line of crap at how great it was, and because Ive used Maytag for years I bought it. Id rather have my 20 plus old one back. At least it didnt take over an hour for a load, and the rinse cycle really worked. WE HATE YOUR NEW WASHER. As soon as we can afford a different washer well be looking for a different brand.

I just bought this refrigerator a bit more than 2 years ago. I have to change electronic module for $300 CAD including labor. Home Depot advised me to contact directly Maytag and to express my dissatisfaction about this unreliable product.

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

The best we can tell, we got our Maytag in 1991. This was because the repairman told us that was the last year they made parts for it. It ran wonderfully until 2018. The water valve broke, but a repairman easily fixed it. In 2019, it stopped running. The repairman fixed it, temporarily, he said. He refused to charge us for his work because he said we might get a few more loads done before it completely pooped out. Were still using it. I love this machine. It has gone WAY past the expected life span of a washing machine. Weve had it for 29 years!

Im really happy with my range. The only drawback is that the upper oven/broiler is a little on the small side. The five burners on top are convenient for when I am cooking a large family meal on weekends and holidays.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

We bought a top load washer and the matching dryer. A thermal switch (I think it’s called) blew in the dryer at about two years. Luckily my husband is an electrician, so he took care of that. WASHER-A little after 2 years the plastic “driver hub” stripped And the agitator has stopped working, the door is having trouble locking and it won’t spin fast enough to get the water out of the clothes. I’ve ordered a new “driver hub” for $53! It is a cheap plastic part. Probably 1 cent to make in China. Robbery. This will hopefully resolve all 3 issues I’m having with the washer. They even charged me 9.99 shipping. $2000 later Maytag/Whirlpool should treat their customers like royalty. I will never ever buy another Maytag or other brands associated with Whirlpool ever again.

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

Maytag msd2650kes refrigerator - I replaced compressor switch three times then compressor went out after only almost four years. We bought all new Maytag when remodeling. Never again will we ever be that stupid again.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

I have had my Maytag Bravo for 5 years now. I originally paid 1800.00 for the set. And yes that is without the tax. Well I also got a warranty. Three years after I purchased my set my dryer stopped drying my clothes. I called the warranty company for a repair man and lo and behold my warranty is over. The repairman came and said that my lint was backed up. He stated that it was a good thing that I called when I did because they have been known to catch on fire. I asked him how is this possible? I check my lint screen and clean it after every load. He stated that the lint falls off the screen and just settles at the bottom of the dryer. And sometimes the dryer will get so hot that it will actually set the lint on fire. He fixed it but now it is back to doing the same thing two short years later. Im thinking that Maytag must know about this now and I am wondering why they havent did a recall on these before someone gets hurt or even worse by trying to do laundry.

At first my dishwasher worked great and I have always been really good about rinsing my dishes before I put them in. Starting a few months back I noticed my dishes were coming out gritty then all of a sudden it started backing up into our sink.

My Maytag washer has been a problem since we bought it. Maytag washer has been repaired 3 times. Stopped working again. I am 78 years old, I have take myclothes to the laundry mat. First, waiting for the repair then waiting for the parts. If Maytag stands by their product they should replace it.

Need to keep cleaning washer otherwise it leaves white marks on clothes. I used vinegar but that didnt help. Used the wash cycle and that didnt help. I found a washer cleaner and it works great. Overall performance of washer is fine but I would be hesitant on purchasing another Maytag Bravo washer only for this reason.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

Mine is the same sad story as all the others. Bought our Maytag dishwasher in 2013 (model MDB7749) and 15 months later, the control panel went out. We have contacted Maytag and they basically told us it could be our fault it doesnt work, so they wont fix it. Now we have learned that this is an issue that A LOT of people are having. We called their special number for this problem and were told they still wouldnt fix it since we called BEFORE having it repaired. So my question is, how is this legal and why arent they recalling this product? I know that there was a class action lawsuit against Maytag for this problem. Why dont we hold them accountable as well? This is bad business and we shouldnt allow them to take advantage of hard working people like this.

I have had my Maytag refrigerator for eight years and it is best one I have had in fifty years. It is dependable, quiet running and easy to maintain. The ice maker is wonderful; it always has ice ready even on the hottest summer day. If and when I ever need to purchase another refrigerator, I wouldnt hesitate to buy another Maytag!

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

Bought a Maytag bottom door refrigerator/freezer about 3 years ago and within 6 months had the bottom drawer ice freeze issue that is so common all over the internet. Today is the THIRD ** time Ive had to take this piece of crap product apart and clear the ice. For all of you who have contacted Maytag in the past... Ill bet you got the same response I did when the fridge was new. They claim there are NO KNOWN ISSUES. They actually told me they had NO RECORD of previous complaints with this issue. MAYTAG SUCKS! I wouldnt take a free appliance from them. Worst customer service possible and they take no responsibility for their ** design and problems. There should be a class action suit for this issue. IF ANYONE IS EVEN CONSIDERING A MAYTAG APPLIANCE... Do yourself a favor and think twice.

I almost didnt write this review because it is just a repetitive representation of this machine. I AM SO DISAPPOINTED with this machine! I had a Neptune and after a few years, it started to spew oil onto the laundry WHILE it was washing! It ruined so much clothing before I figured out what was happening. Came to find out, it was a glitch with the machine that the company SUPPOSEDLY, sent out notices about but I never received. Now the Bravos X... Bought to replace the Neptune, as it was advertised to replace Front loaders. Would accommodate a KING SIZE COMFORTER with no problem... Got out of one problem to get into another!!!From the beginning, I wondered how does this machine get the clothes clean? How would it was a king size comforter? It doesnt agitate like the other top loaders. I figured it was a new top of the line kind of technology. My clothes started to tangle up really bad even though I was not filling the machine over excessively. The clothes were staying dripping wet over and over again. It doesnt matter how much clothing is being washed, they stay super wet. I have to go through the Drain & Spin cycle to finish the cycle. IT GETS OLD!!!! I HATE THIS MACHINE!!!! Doing laundry is a HORRIFIC CHORE for me. This machine is TERRIBLE. NEEDLESS TO SAY, I CANNOT WASH ANY SIZE COMFORTER!!!After reading all these reviews, seeing how Im NOT the only one who is going through all these problems with this machine, I refuse to call any repair company! I wont spend another penny on this monster!!!! I WILL NEVER BUY ANOTHER MAYTAG ANYTHING AGAIN!!! Reason for this review... So anyone who is considering buying a Bravos X washer, think again. Hopefully you are doing your homework and will not make the same mistake we did!!!! Thank you for your time and attention to this matter.

There should be a recall. Just look at the number of people complaining about this same exact occurrence about the control panel not activating. Im on my second control panel in 24 months. Some people are on their fourth already. Give me a break. There needs to be a recall and a redesign of this thing, which turned out to be a piece of junk washer.

I have always had faith in Maytag when it comes to appliances. As of yesterday, it is gone. We purchased the Bravos XL dryer in January 2013. Last weekend it was running, but not drying. We placed a call for a serviceman to come fix it. Discovered the heating element had gone out on it. We had to pay $300 for the repair. I am greatly disappointed a $1,000+ dryer is already having issues. Maytag should stand behind this problem and offer to pay for the damages, as from reading the reviews, it looks like this is an ongoing problem. Maytag should be ashamed of providing a product of such poor quality.

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

I have been Maytag customers for 40+ years. I purchased a new Maytag washer and dryer at Home Depot last year. The paint is coming off and the top is starting to rust. We have had Maytag washers and dryers for as much as 17 years that did not rust. The reason we bought Maytag was quality. Rusting in one year is not quality. Please contact us ASAP. Home Depot said there was nothing they could do.

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

This is the absolutely worse washer I have ever owned! My clothes actually come out dirtier after they are washed. It leaves white stains on clothes that I have to scrub out by hand. Maytag you should be ashamed of yourselves for coming out with a washer like this. It takes me 2 or 3 times to wash clothes and I have to use the power wash, extra rinse, and maximum clean setting to even come close to cleaning. It is cheaper to take my clothes to the dry cleaner now than use the washer. I called Maytag numerous times, and they said that they will charge for a service call unless there is actually a mechanical issues. They will not honor repairing the machine if it does not wash clean. I will definitely NOT recommend this washer.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

Pleased with all the features. I have had zero problems with this Maytag refrigerator; no problems with the ice maker; the crisper works well. The adjustable shelves are so convenient.

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

I purchased my Maytag Neptune pair on Jan. 24, 2005. I was unaware of the problems and lawsuit related to these items. Luckily, I didnt have any problems with them until May of this year. At that time, I spent $337.00 for a new control panel for the dryer. (Just because I didnt want to split up my set.) I expected them to last me for the rest of my life. Of course, the washer had started to do something even the repair man had never heard of before, right about the same time. I told him that the tub would fill up with gallons of water, and surprise me when I opened the door on various occasions, flooding my laundry room and the basement downstairs. Mind you, this would occur even with the water supply cut off to the machine, no hot or cold running to it.He performed a diagnostic test on it and said everything showed up fine. Of course, it didnt overflow while he was here. He is the one who told me about all the trouble and the lawsuits. I had wondered why I didnt see them for sale anymore. I have been keeping the water turned off except when I need to use it after all this time. It still happens! The repairman thought I was senile or something. I dont have a mold problem, no trouble with the door lock (yet), and out of all the comments and complaints Ive read online today, only this site had one with a problem of it flooding the house. My husband and I are on a fixed income, and here is this unit (that I thought would be my last) rotting out my floor and wall in the laundry room, and flooding my basement. Not to mention it rusting out the inside of the washer and its pedestal. I would like to hear from anyone else who had this water problem, and what it took to fix it.

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

I had purchased a Maytag Front Load Washer Model no. MHWE300VW00 in 2009. Now the rear tub, basket, and belt are gone. I will never purchase another Maytag product and would not recommend them to anyone.

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

We bought a top-loading Maytag washing machine in January 2020, and are very disappointed. Clothes do not come out clean. We called the Maytag call-center and were told that “high efficiency machines are different”. They use much less water to be green, but now I have to wash items several times, negating any energy conservation. This also takes more of my time. If we use the “deep water” option and power cycle, clothes are almost clean; however, it takes 1 hour and 45 minutes per cycle. My 18-year-old Whirlpool washed clothes beautifully in under 45 minutes. This brand-new Maytag is NOT an improvement. We use the correct HE detergent and have tried with warmer water, and all of the different cycles, but still do not get acceptable results. The Maytag washing machine is not effective at the one thing it is designed to do, clean clothes. Our specific model is MVWC565FW1, however the saleperson told us that all models are similar.

My Maytag dishwasher is very easy to use. Saves on money and time. I enjoy it and it have made my life so much easier. When you cook for two you can be out the kitchen in no time.

We purchased the Maytag Bravos MCT in July 2017. Just passed the 1 year warranty and the glass door just shattered. No reason for it really other than it must have been defective. Nothing dropped on it and it wasnt cold or hot in the room. I got nothing. Maytag said they didnt know why it would happen, and would have to send service tech out. A lid for this type of washer alone is $200-$300. Buyer beware. Dont get a glass top loader.

Bought a Maytag microwave model MMV4205DS and I too have had an issue with open/close door display. Just like other reviews Ive read it started out once in a while for the first year then began happening more often til it stopped working by the second year. I also read someone asking why there isnt a class action lawsuit? Good question. Way too many bad reviews on same issue. If I knew how and if we could start one then I would. Thought we could trust a company thats been around for so many years. Wish we had check into it more and I have learned from other products to do just that from now on. Have a backup microwave by GE from WalMart weve had for 10 yrs still working.

Water level is totally inaccurate, if you do get enough water in it, it will not spin clothes dry. This is the worst purchase I have bought in my entire life. This washing machine fails in every aspect period!! AND the matching dryer is a waste of space as well, clothes come out damp regardless of setting or time period. When I was younger, Maytag meant something, not anymore! I have searched to see if there are replacement sensors, or upgraded components to make these machines work properly, that I would even be willing to pay for myself and get them installed to make them functional, but NO they dont even offer that... we are just stuck with them. My water bill is higher and my electric bill is higher too! From these machines. I wouldnt even sell them used to another person. I wouldnt want them to inherit these problems, but as soon as I can save up enough money {being disabled} I will get these hauled off and buy a set of Speed Queen machines. My wife and I are so repeatedly disgusted!! I wish I had the receipt so I could post it for more proof.

Both work good. Washer could be a little lower and it has quit rinsing and I cannot use it. But it is 9 years old, I think for their age they were a good buy. I plan to get the washer repaired because have been satisfied with how clean it gets my clothes and it washes pretty quick. I got the large capacity and with a very large load the washer gets them clean. The dryer is very good. It is just as good on a large load as small, dries quick. I would buy this type washer and dryer again and would definitely recommend it to folks. I have been very happy with this washer and dryer. The paint is coming off the washer where you put detergent and fabric softener in and it has rusted out some but it is getting a little age on it so this is expected. I like it, I can throw my comforter in and it gets it clean and the large loads always come out great. I think anyone who bought the set would be very happy with it. It is also quiet which I like.

Bought this washer and dryer 3 1/2 years ago mainly because of Maytag name and reputation. They were very expensive to purchase. The washer is a piece of junk 3 1/2 years old used for my wife and I and leaks oil all over the floor. Called repair man to come and look at it, wasnt here 5 minutes said transmission is shot. Cost over $400 to have it repaired. We are junking it and that will be the last Maytag product I ever own.

Bought a Maytag top loader washer from Lowes in July 2017. Have had nothing but problems due to faulty computerized guts. Worked intermittently and took a long time to wash compared to older machine. Repairman out twice... replaced computer board and still have problems. The machine was made in Canada according to the label. Hey Canada, what is going on making junk? Too bad that we did not know beforehand what junk the Maytag brand has become. Lowes should not sell this junk to help its reputation and valued customers.

Both Sears and Maytag have lost my business FOR GOOD! We purchased a Maytag Bravo XL # MGDB980W0 2 years ago. We called within the 1 year warranty period via Sears, they sent a tech out then charged us. The dryer kept shutting off before clothes were dry. We thought the problem resolved, then reoccurred after the 1 yr period. Neither Sears or Maytag would stand behind the product citing it has been discontinued due to problems. Well... yeah, no kidding. We paid BGE energy efficiency company to come out and evaluate it. They tweaked the exhaust vent and cleaned out the duct, however, they said we needed a new sensor. My wife bought a new sensor, installed it, and the dryer still wont work right! (Shutting off prior to clothes being dry). BOTTOM LINE UP FRONT: I researched and bought a new gas LG dryer on sale at Home Depot and shelled out $849 unnecessarily thanks to shoddy product and lack of company integrity. DO NOT BUY SEARS OR MAYTAG!!!

We bought our Maytag Bravos washer and dryer 3 years ago. We bought the set from E-Z RENTALS in Crossville, TN. We paid on the set for 2 years. You can only imagine how much we paid. Two weeks after the payoff, the washing machine started acting up. We were led to believe that the set had a 10-year warranty on them. They made sure that we saw the 8-10 sticker on the front of the machine. E-Z Rentals said that we had to pay extra for the warranty. They hung us out to dry. I could have bought a nice car for what we paid for this washing machine. Now its torn up again. This will make the 3rd time that we have had to call a repairman. We are ready to take the washing machine to the dump and buy a Whirlpool. The man at E-Z Rentals said that on average, the Bravos machine lasts for 3 to 4 years. After that, its cheaper to buy a new one. Does anyone know if, in fact, these machines come with any type of warranty? We truly do not have a clue. We would be grateful for any information on the washing machine. This has been a hurtful experience. I feel that we were taken advantage of.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

Maytag centennial washing machine - I am pretty good as a mechanic or this machine would sit unused. Purchased in 2/15 at lowes. Poor installation. Then the machine... I hooked it up properly and ran it with extra load setting to see the machine develop a life all its own. The sheet metal breathed in and out like the chest of an old man running uphill. Lower exit hose not properly installed leaked on floor so I put on a new adjustable clip. Machine can only handle small loads. While it does wash clothes (it is a washing machine!) it requires close supervision in size of load. The machine needs a plumbing bang pressure gauge or you are likely to blow out your water pipes. It sounds like there are a bunch of people walking the machine with ball peen hammers. Who cares, but they were made in America and moved to Mexico. They should need visas to get back in. Absolute junk.

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

Dont buy this machine. Although it is an HE machine and supposed to save on water, it does not give enough water to at least cover the clothes. I had repair come in and they changed the computer but no improvement. The cycles determine the water amounts not the type of clothes you are washing. So if I only a few things I use cold water wash, if I have a half load I use deep water wash and have to add water to it. Its ridiculous. Do yourself a favor and get an LG. I wish I had.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

The Deli drawer randomly falls, shelves in general do not fit well. Rough edges on door corners are a hazard especially for children. Service call line was extremely poor with a total disregard to customer concerns. It has been a very bad decision!

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

Purchased in 2013, they have replaced the control panel twice in 2014 and AGAIN 2015, now WAITING for the replacement control panel AGAIN. Maytag claims there are no recalls on this dishwasher model number. But after reading all these reviews why is there not a recall. Maytag is of no help when you call. They claim as long as they keep replacing the control panel it still can be repaired. This can be extremely costly WHEN THE CONTROL CONSOLE PANEL keeps breaking. Obviously there is a major problem with this part and why is Maytag not recognizing this issue.