We have a Maytag Dishwasher Model MDBTT60AWB purchased from Lowes about 8 or 9 years ago. This model was included in the huge 2010 recall of 1.7 million units due to the possibility of heater-unit fires. For the last couple of years, its had a problem staying on the selected cycle: After being started on normal wash, it reverted to rinse only after a few seconds, but eventually quit responded to the selection of other cycles altogether. Removing the back from the door to expose the innards revealed the ribbon cable that connects the circuit-board head to the control panel had worked loose. Reattaching it provides a temporary fix, but it eventually works loose again. We suppose the screw holding the back to the door will strip sooner or later, but by then well probably be so fed-up with fixing it that buying a new (non-Maytag) one wont seem like a bad option.

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

My dishwasher is two years old and it just stopped working. I called the store I purchased it from and they sent out a repair man. He told me that the control panel was damaged and that he would have to replace it. The cost is $145.00 plus the $50.00 service call. He said something must have spilled and got into the control panel. It is a built-in dishwasher underneath a kitchen counter. I think it should somehow be protected against spills and/or moisture getting into the control panel as it is underneath the kitchen counter. I do not remember spilling anything that ran down the front on the dishwasher. But even if something spilled, if it was made properly it should still be working. I will not recommend a Maytag to anyone and will also spread the word about what happened. Unhappy in Pennsylvania.

Lets see... my complaints are the same as the others. I purchased the Maytag Bravos set. They were the higher end units. At first, the machine was very quiet. I quickly had a control board go out. Got that fixed. Now the washer gets off balance on every load.... Every time it spins, it stop. The gears whine very loudly... Louder than any other machine Ive ever heard. I agree with the comments on wrinkled clothes. It also does not clean heavily soiled clothes as well either. Overall, a bad decision.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

The mid level dishwasher is excellent, easy to install. Very quiet. The dishwasher cleans well and does a great job. I wish the default would go to the last setting instead of auto. Highly recommend.

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

I have been trying to get my refrigerator repaired for over 5 months through the extended service plan I paid for. They sent out a service repairman. He could not repair the refrigerator without some parts so he ordered parts. We waited months to find out he can not get the part anymore that he ordered. So now Maytag Extended Plans and Service Power said they would have to replace the whole refrigerator but every time I call about it, they give me the runaround and say someone will be calling me back within 48 hours.I never get a call back. I give them a few days, then I call back and get the same runaround again. Im getting nowhere with these people. My refrigerator is a $6,500 refrigerator that Im sure they just dont want to replace or offer me anything for that matter. They should abide by the contract I have with them.

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

Washer sounds like gearing is broken, is noisy during operation, various combinations of options dont work, appearance of only one agitation cycle combination on washer, just many settings but all with the same response; dryer does not timely dry clothes, all settings default to the same palpable heat temperature; clothes take much longer to dry in new dryer than they did in old Maytag. Newer Maytag set appears to be secondhand garbage sold as new by Menards. Company unresponsive to complaints.

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

This Bravo Top Loading Washer does not thoroughly clean my clothes. It doesn’t fill properly with water, and it leaves soap residue on my clothes, because it’s not using enough water. I’m using the 2 rinse cycle trying to prevent this, and it’s still not enough. It has actually ruined a few of my items. It is the WORST washing machine I’ve ever purchased. I’m disappointed in Maytag for producing such an awful machine and Sears for selling such a sub par product.

We bought a Maytag Centennial Washer in 2011. 6 months ago the control board went bad. Maytag has an exorbitant replacement price! I went to Ebay and bought a NEW board for 1/7th of the price Maytag wanted. The old board was marked revision B. The new board is revision F! That indicates to me that the board was defective when it was new and they have made 5 attempts since then to fix it! No recalls however. Now the motor is shot. I found out the motor from Australia is also inferior! So this 5 year 3 month old POS Maytag is going to the dump! We will shop for something made outside the US. No not a Samsung. I think there should be a class action suit against Maytag.

We 19 years and gently used. The door latch broke. We purchased a used quiet series Maytag dishwasher and found that the door latch failed on this. I recently found over 600 complaints for the same problem. If you are receiving this many complaints and its one of your most frequent complaint, do you think its time for a redesign of the door latch mechanic is??? Or are you relying on your reputation and dont care about quality anymore?This is it for Maytag. Im glad we didnt buy a new Maytag because we would be stuck again with a crappy door latch. If you cant be bothered with fixing your door latch issues and you know that you have a long term problem here, you at least can send a new door handle kit to those of us who are complaining. Of course you wont do that. And the only recourse I have as a consumer is to tell others about the ongoing problem with your front door latch on my social media. Sadly, you are now only another crappy dishwasher with no real quality control. I bought several appliances from you because of your reputation for appliances that last. Seems that is now a myth.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

Maytag has always been my choice with appliances. Ive purchased others and always dissatisfied. This dishwasher has been a trooper and lasted forever. Its been overworked with 4+ children and yet still going strong. I recommend Maytag????

I have a Maytag refrigerator that is 7 years old. It works fine except it needs a new freezer door gasket. In trying to get the part so it can be repaired I discovered that they had chosen to discontinue production of this part. I can no longer get it anywhere. They were the most unhelpful customer service I have ever worked with. They refused to try to find a part for another model that may work. They refused to offer a discount on a replacement product. They even refused to give me a phone number to talk to management. I had always been a loyal customer to their brand prior to this but I will never again purchase a Whirlpool or Maytag product. I dont expect not to have an issue but I do expect the ability to be supported in obtaining a commonly replaced part for a major appliance that is less than 10 years old.

I purchased a Maytag top load HE Bravo 700 3 yrs ago. I only wash 3 loads of laundry a week and the bearings went bad in the washer! Maytag/Whirlpool will do nothing to help me because they say I should have purchased the extended warranty. Well there is NO WAY that I could have worn out those bearings; it was a manufacturing defect that caused them to fail and hundreds of people online all say they have the same issue. The repair cost is $400 and would only have a 90-day warranty so I might as well purchase a new washer. Home Depot (where I purchased the washer) has been very helpful and is offering me help on the purchase of a new washer, but even they could not get Maytag to do the right thing and repair my Bravo. I am going back to a none HE machine with an agitator. This has been a horrible experience and Maytag has no business putting commercials on TV that say they are dependable.

I bought this Maytag refrigerator model MF 12269FRB00. It is not, user friendly, meaning that condiments and small bottles just dont fit conveniently in any space, The biggest issue is the ice maker. The ice maker shoots ice out on each and every attempt. Every time you want ice you are guaranteed to have ice shoot out of your glass on to the floor. I often challenge my guests to get ice without the cubes shooting out of the glass. No one has ever won. Dont buy this piece of crap, unless you find humor in having ice on your floor every time. Shout out to Grays Appliance in Melrose for selling crap! I will never buy from them or Maytag again. To the engineers who designed this product, you suck too!

One month after warranty we had our first issue which cost us $380. Kinda my fault I was told by repair guy... My bra underwire came out during wash and destroyed the part we had to replace. Then a year later during spin cycle it sounds like an airplane taking off for about 10 minutes. Its so loud we cant even hear our TV! So guessing its bearings gone bad now? Which is a very difficult part to replace. And pricey. So guessing a new washer is in our future. We previously owned a Maytag washer and had it for 15 years and it still worked fine, we just wanted to upgrade. Big mistake! I wouldnt wish this washer on my enemies. I think the repair guys sets it to mess up when they do this reset thingy. Lol. Cause within a month of the renewed warranty we purchased was expired is when the 2nd issue began. I think the older washer are better because all this newer technology stuff is crap!! My advice do not buy Maytag Bravos series washer unless youve got lots of cash for repairs!!

I have a Maytag washer that I bought new in 1995! It is still washing my clothes like a champ. It must be true - the Maytag repairman is a lonely soul, in all these years I have never had to call him!

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

I purchased a Bravo Washer and Dryer from Home Depot. The Maytag Bravo washer and dryer we purchased from Home Depot did not work from the beginning. Before I called Maytag, I tried for several months to redo the way I was loading the washer and dryer.I tried several different settings however, the clothing keeps coming out smelling like it is still worn. Spots are in the clothing that normally comes out with a washing (with my prior washer). The clothing just does not get cleaned and it gets so tangled that it has ruined some of my clothing. There is clumping of the detergent, even though not a lot has been used.I had the repair company come out three times for both the washer and the dryer. They have checked and no errors codes where found. One gentleman told me again to redo the way I load the washer and the dryer. I have done it so many times, but I tried again and even purchased little dryer balls. It made no difference.I called Maytag again and was told they would have to have another company come in and do a second opinion. The person came and said that he agreed that the washer should be able to wash and the dryer should be working correctly. He recommended that a possible problem with the motherboard for the dryer (which was a possible problem mentioned by visit #2) could be handled, but he had to have it approved. He would check with the company and get back to me. I received a call the next day and a message was left telling me there is nothing he can do with the washer. He was told by Maytag/Whirlpool that I should only fill the tub lightly and not pack it down (I told everyone how I load and I never pack my clothing down). The washer should, when loaded with wet clothing, be only 1/3 to full otherwise it decreases the wash ability dramatically.The problem of the siphoning action for the softener section of the washer should be handled by running boiling water through the tube to loosen up the wax portion of the softener. The possible correction for the dryer exchanging the motherboard (it could be set incorrectly) was turned down by saying that the dryer is running to Maytag/Whirlpool’s satisfaction and nothing else would be done, since there are no error codes for both washer and dryer.My towels have a mildew odor to them when they are used. They have to be washed twice and run through the dryer a long time before I can put them away. I purchased a high capacity washer and dryer and I am told now not to fill it more then 1/2 full. That is not what I was told by the person selling it. Otherwise, I would not have purchased this set at all.

We purchased a Maytag Gemini with serial number D40941338 and model number MGR6875AD826. It has been a complete disaster. The control panel keeps breaking down, and its now going to be replaced for the 6th time. I have asked for a new stove when I called the Maytag Extended Warranty Department, and they will not replace this defective product. Please help me.

After one year of service from our Maytag Jetclean Plus Dishwasher with Toughscrub the circuit board went out. I have been seeing and hearing other people complaining about this problem. We purchased this device based in large part on Maytags reputation for reliability. I am not happy with this machine. I will complain to the company and write another review based on the results. I suggest Maytag goes back to the old knobs until they can assemble and protect the circuit board, which I believe was damaged by heat and moisture.

Purchased French Door MF12269VM 22 inch from The Brick furniture April 1, 2012. Turned out to be a real April fools joke. Purchased extended warranty with TransGlobal for 5 years. First, fridge delivered after about a couple of weeks because it actually wasnt in stock. Naughty Brick lied about availability. Fridge arrives and after a service call from Maytag repair, they ascertain compressor doesnt work.Order fridge number 2. Two weeks later, get second fridge but lever for dispensing water is broken off. Order fridge number 3. Usual two-week wait and fridge finally arrives but the whole side panel is damaged. Send it back and order Fridge number 4. Service from Brick, Maytag and Whirlpool, terrible customer relations. Misrepresented delivery dates, supply issues, and operational damages.Fridge finally installed. Ice maker operates intermittently for the next year. Service techs from TransGlobal offer a variety of suggestions including changing filter, water pressure issues. Finally ice maker stops entirely in Summer of 2013. Is replaced after a month of waiting for parts of which the wrong part was sent. Ice maker continued to operate intermittently. Sometimes just a small of ice or no ice for a day. Finally in May after another service call, ice maker stopped working for about 4 days. Tech comes out and miraculously, it starts working again. A month later stops again and hasnt worked since.Contacted TransGlobal off shore call centre? And arranged to have an assessment to see if we needed a new fridge. Request declined and Maytag (Whirlpool) sent a tech out after another week. Service tech recommended new freezer. Waited a week for parts and arranged for Service tech to replace ice maker. Wrong ice maker part (for the second time) in less than a year.The latest trick from our possessed fridge is recent alarms from the temperature control. To say we are disappointed in this product, the retail experience, the quality of the manufacturing, the shipping procedures, the poor engineering and design, doesnt come close to describing the shoddiness surrounding this appliance and the service weve received.In conclusion, we are still awaiting an ice maker and are contemplating buying another fridge. What it is fair to say, we will never ever buy another appliance with their the Whirlpool or Maytag attached to it. Nor will we ever again buy anything from the Brick, or depend upon TransGlobal for repair services. Are there other Manufacturers and retailers out there who understand the meaning of service and quality. I certainly hope so. Otherwise Im going to invest in a good icebox.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

Maytag will not fix 2 major issues with new $700 Maytag dryer bought from Home Depot who takes no responsibility. They wont return it. Maytag wont replace defective dryer unless technician from totem appliances cannot fix problem. The tech ordered a control board and timer. Only installed the timer. He did not fix 2 issues. Dryer never stops at OFF. Dryer leaves damp spots on any clothing whether small or medium large load. Was told by Maytag if damp spots then its OUR problem... our ventilation. No it is your sensor. Our model is ymedc465hwo serial m820. 07331. Bought in late Oct. 2018. Two supervisors later we are being sent to tech or tech company and played games with. All I know is Maytag sells defective dryers then wont replace them or fix main issue.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

Bought this washer back in March of 2016. This is the biggest piece of garbage that I ever came across! That washer does not clean clothes, when they are dirty. If I stand in the rain dressed in dirty clothes, they get cleaner than in the washing machine. In 5 month I have tried every possible variation of washing to no avail. I have to handwash the clothes that I wear to work in the garden, or any other dirty job, because the washing machine does not do the job! I bought that washer at ABC warehouse, I paid almost $400 for the thing, and I have to handwash my dirty clothes!!! Shame on you!!!

After 2 years the oven didnt work. I had a repair fix it for $500 but if I wanted the convection to work it would cost another $800. Obviously not worth it. Now the oven needs to be set at 400 if I want then actual temperature to be 350. Now the latest - the racks are too small and falling! I just put my Le Creuset in the oven and the rack fell. Splashed everywhere! This happened at Christmas with my turkey. So bought the fridge - everything in the back freezes. Never ever buying Maytag again. Im guessing the Maytag repairman isnt lonely anymore.

This is not about a Bravo but Maytag is the biggest piece of junk Ive ever owned. Have not had the washer but a couple of years and is leaking somewhere inside of the machine. Have to turn the water on and off just to wash clothes and still laundry room floor soaked. The dryer I have to run for 70 mins. on high heat at least twice to dry clothes, 3 times for your towels. Of course it lasted long enough so the warranty had run out. Never ever again would I buy this crap.

Stove does not heat evenly in oven. Electric burner cannot be turned down to low or simmer, then it will not cook at all. Other burner turned down to low does not stop bubbling and stays at a high temp. There is no consistency. I am extremely disappointed and curse at this stove every day. Model #MER7664XB. Serial #R13316302.

Gemini Twin natural gas range - I bought this range approximately 18 months ago. I thought it had all the features I needed and it looked good -- looking good is just about all it does! If you are a real cook I would suggest you avoid this range. The burner controls are preset and it is impossible to turn the flame very low if a simmering heat is required. If you are making meringues, again, the oven heat cannot be turned to a cool enough temperature. Ovens bake/broil unevenly. It takes forever to bring a pot of water to a boil, not because the flame is not hot enough, but because the pots sit far too high above the flame. Bad, bad design. Probably designed by someone who eats take-out!!

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

I purchased Maytag French door stainless fridge 5 years ago for $2200. The doors were out of alignment and I put in new control board; both items almost right away. Then in May 2011, we had to replace another control board for about $400. Then in July 2011, the compressor went out at a cost of $300 for the compressor, $350 for labor. I called to Maytag, Gwen agreed to pay for the compressor but not the labor to put it in. So we now have about $1400 invested in our $2200 refrigerator. Letters to Maytag CEO Mr. Fettig remain unanswered. Do not buy a Maytag appliance!

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

This is the WORSE POS I have ever owned/used/etc.... our clothes are dirty, w/ a scummy film, really bad in most cases. Some have weird stain appear that werent there. Electric & water bills up. Have to always use deep water wash, double rinse. My clothes are wet when I put them in due to sensor fill (extra weight), also a zillion mesh bags. Clothes are getting trashed, faded so bad & smell bad. Having to use a cleansing product monthly, in one aspect, should encourage the engineers that signed off on this POS to change careers. Maytag customer service says no complaints have been filed!!! Horse **!!! $ 800.00, trashed, unclean, wrinkled to the point of almost needing to iron all your clothes. I have been going to the laundromat. Engineers should have been FORCED to use this machine at least 2 months.... good reviews my **.

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

Bought in July 2015, brand new from Lowe’s or Sears. When working to its full potential it never cleaned clothing very well, had no designated spot for detergent or softener, just bleach. Just last 3 years and it’s a piece of crap that has to be replaced. Going to argue with the company to tomorrow to get them to replace the broken transmission which may or may not be considered part of the drive motor - all **. This is a very expensive machine that didn’t last a month beyond 3 years! The 10 year warranty covers the 2 most rugged parts of any washer... the agitator never truly cleaned my clothes and now it is fused to the wash basket and cannot even be replaced without being chiseled off. Worst machine, purchase, and brand ever???

Had the washer for less than 3 months just a week before the 90 warranty was up and it stopped spinning. Called service dept. What a joke for this company that keep yessing you. Took a week before someone came out. Said washer needed a new motherboard and they would only cover it once but there seems to be a ongoing issue with their motherboard. Had to wait over 2 1/2 weeks before they would have one in stock. The tech installed it however now when it spins seems she left the top loose.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

When my house burned in 1995 I purchased all Maytag appliances when we rebuilt because I had good performance from them up to then. My washer and dryer even made it through the fire and are still going now 14 years after the fire. They are 34 years old. The other appliances I purchased were a chest freezer, dishwasher, stove, and, a refrigerator totaling around $2,000, a pretty sum in 95. I have nothing but good to say about the freezer and the dishwasher, however, the refrigerator and stove stick me in the side every time I look at them. I purchased a smaller refrigerator than I had planned because I was PROMISED that the refrigerator was designed to hold the milk in the door. The first thing that happened when I opened my brand new refrigerator was the shelf holder broke and the milk fell to the floor making an awful mess. They ordered the shelf holder assuring me it was a fluke and sent me on my unhappy way. After I got the part I installed it and crack-smash-pow-swoosh! It happened again! I called the store I purchased it from and they said they ordered extras so to come in and get them, that I had probably installed it wrong. Went like this and I finally told him like I told him at first I do no want this refrigerator! You said and the pamphlet says it is capable of holding a gallon of milk in the door. It does not. It cant even hold catsup bottles without breaking. Thats when he told me that yes, they were having an issue with this refrigerators door shelves. He then gave me the rest of the shelf ends he had and said after that they were gone, they had discontinued them. Also said I was past the days to trade my refrigerator. I told him that was because he kept stalling me, ordering parts. LEMONS AND LIES. Now the refrigerator sits in my laundry room, freezes food in either section on its own whim, and the shelves are held on with DUCT TAPE. I have multiple correspondence with the company but gave up as I was seriously hurt in a vehicle accident and had to put my energies to surgeries and healing. And dont get me started about the stove. I will not be buying Maytag anymore.

I bought a Maytag Bravos top loader washer and dryer less than 2 years ago. I started having problems with my dryer 3 months ago and after several service calls (and a few hundred dollars), it still does not dry our clothes. I spent over $1500 for the pair and was excited to have a top end washer and dryer. My biggest complaint is with the manufacturer, Maytag - they just dont seem to care. I did not buy the extended warranty for two reasons. First, I bought a nice unit and expect it to work properly for a reasonable amount of time (at least 4-5 years without any problems). Second, they are just a bad purchase and they cost about half of the unit and if you buy a nice unit, you shouldnt need one. I could have bought a new dryer for what I spent to try and have this one work properly. My wife and I spent $600 for our last set which lasted 7 years without a problem; they were manufactured by GE, which I now wish I would have bought another GE. My wife talked me into buying a new pair to accommodate the needs of our growing family. I wished I would have kept the GE pair that was working.I would not recommend any Maytag appliance: they really just dont care to provide any reasonable service to stand behind their products. What a shame. This reminds me of why many foreign manufacturers are beating us at what we used to do best - make products that last and work! The washer and dryer look nice and have many great features, but these dont matter much if they dont work.

This washer is the worst piece of junk I have ever purchased. From day 1 it never cleaned my clothing. It was too much money to call a repairman so I have lived with it since October 13, 2013 and I have finally been able to buy a new washer this week. My husband would come home from work and ask me why I put dirty clothing in his drawers, he said his clothes stunk and were stained. This washer just did not clean the clothing. It didnt use water. I cannot say how many times I would open it after washing a load and the clothes were dry. It saved water alright, it didnt use any and it was installed properly. If you are going to purchase a Maytag Centennial, run. Dont walk. Run, fly, look the other way, just dont buy this HUNK OF JUNK! I cant even sell it, so we will sell it on eBay for parts just to recoup some of our hard earned money! MAYTAG YOU SHOULD BE ASHAMED OF YOURSELF!

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

We have the 4000 series front loader washer. Within 8 months of owning it, it would shut off in mid cycle. You have to unplug it to restart it. Then, when it completes the cycle, it is still soaking wet. So, you have to put it through the drain and spin cycle again. There is something major wrong with the spin cycle. It takes about 2 hours to do one load of laundry and you have to stay home to do all of the steps. It costs as much to fix it as the machine costs. It’s the worst washer we have ever had. No more Maytags!

I called Maytags customer service about an over the range microwave that was bought 2 years ago and barely used. The mechanism in the microwave on the latch for the door, clicked into the body of the unit and therefore the door does not register closed which doesnt allow it to come on. After explaining this issue to the customer service rep, she insisted that the only thing that Maytag would stand behind was the part if needed. A service call would be between $100 - $150. The microwave isnt even that old and why would Maytag not stand behind a like new unit? I bought 3 Maytag products and I am now regretting it. I had asked to speak to a supervisor and she just proceeded to repeat the same thing the sales rep did. They will only cover the cheap part if needed.What happened to Maytag being top of the line? Apparently they dont care about standing behind their products and would rather you buy an expensive extended warranty to cover their cheaply made appliance. I think they should be under review as a company. I would somewhat understand paying if my appliance was 5 to 10 years old. But its basically new. How is there no protection for customers when it comes to purchasing lemons from an appliance dealer? I will NEVER buy Maytag again and plan on selling my 2 other newly purchased appliances before they have issues. Maytags reviews on social media are terrible. All they offer are the words Im sorry and I understand your frustration. I assume thats just what they have written down in front of them to tell everyone who calls with issues. How do you not stand behind your products! I wish I could select no stars vs the 1.

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

I bought a Maytag dishwasher on June 2008. This new Maytag dishwasher replaced an older Maytag dishwasher that caught fire and was recalled (I found this out after calling Maytag). The new dishwasher (Model: MDB 5601 AWB) also had a recalled part (heater coil) in February 2011. Two months ago, (the unit is now 3 years old), the control board started malfunctioning (certain cycles no longer work). I called Maytag today (Aug 24, 2011) but I was told by a Maytag representative that there was nothing that they could do. After reading so many complaints, I am ready to file a class action suit. It seems that this company continues to perpetrate fraud against an unsuspecting consumer for they knowingly continue to manufacture defective products.

I ordered my dream refrigerator (Maytag Model MFT2776FEZ) on 05-12-2017. I had to wait 4 weeks for it to arrive because it was on back-order. I was willing to wait. All was good for 6 months. January 2018, the six month old refrigerator quit cooling. It took 2 1/2 from the service call until the part came in to fix before I could use my refrigerator again. I lost all my food. The same thing happened again in March 2018 except that it took 4 weeks for the part to come in once the serviceman ordered it. I lost all my food for a second time. February 2019, the same thing happened again. I placed the service call on 01-31-2019 for service, but the tech could not come out until 2/6/19. The part had to be ordered and could not be installed until 2-28-2019. For the 3rd time, Ive lost my food. My best friend that has appliances that are nearly 30 years old. She was going to replace all of hers and get exactly what I ordered. She has changed her mind and has decided she would rather keep her outdated appliances because they work.

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

Frigidaire makes a good fridge. It works good. It has an alarm when you leave as door open. Great appliance. If I could afford it Id get another one when this old model I have gives up on me.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

My dishwasher like many others have mentioned is experiencing the same control panel issues. When I set it to Wash, it spontaneously goes to Rinse Only. I am unsure exactly the age, but given the number of complaints Ive read, with the same problem, it seems as though, there was a flaw many years ago in design and regardless of issues hasnt been resolved with the newer models either. I realize appliances dont last forever, but Maytag was always known for the lonely repairmen and Id hoped the brand would continue to live up to its advertising, despite being purchased by Whirlpool.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

We had perfectly working 20 year old top loading white Whirlpools w/ an agitator, when we remodeled our home and wanted new pretty grey appliances and decided to donate our machines to the church. I chose Maytag top loading due to their former reputation we experienced with dishwashers, etc. It had an agitator, deep fill option, extra rinse, etc. The sales person at Home Depot stated, the agitator is because people like you still want the agitator, and the deep fill will give you the water you have been used to. Not so at all!!Clothes get wound up together, even with filling the wash tub in bundles, there is almost NO water to thoroughly clean & the rinse cycle is a joke. Clothes do NOT come out clean. Im 58 yrs. old and have been doing laundry since I was 13 so I know what I am doing. Its just my husband and I now, and he is so upset that his clothes are pilling probably from rubbing together, even though I occasionally use laundry bags. I seriously wish I would have saved my money and kept the 2 perfectly working whirlpool units I had. This has been such a disappointment. I sincerely would not buy these.P.S. Weve had service out at least 5 times in the last year, and all they do is test the washer and tell us its working as intended... The last thing that is going to happen is we are going to get refunded for a different set, even though we were educated over and over what it would do by Home Depot associates. We are heartbroken. Maytag is going to lose their former reputation on these washers a dryers :( There is simply not enough water to clean or rinse things!

The machine can clean even king size quilts, and clothes come out very clean. It is a front load and there are no problems with odors. There are many cycles to choose from. Cycles spin gently enough while getting out most of the moisture.

Really havent had any problems. The Maytag repairman really is lonely. Great quality wash machines and dryers for that matter. I havent had to do anything. Spins well... Very quiet, no complaints. Dryer works well too. Many cycles area to put fabric softener and bleach. It has a extra extraction cycle and many other features.

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

Bought a Maytag French door refrigerator MFT2976AEM01 in August 2013. Started having problems before the refrigerator was a year old. I called to get it serviced and it took 4 months to get a repairman to check it out. He fixed one part and then ordered another part that he needed which took 3 months to get. After he replaced that part the refrigerator continued to have problems. The serviceman has been out to repair my unit 6 times so far. He has no confidence in the Service Engineers from Maytag. They recommended yet another part be replaced, however now Maytag will not cover the parts cost.They offered to let me buy a new fridge at a discount. After spending about $2700 in August 2013, I dont have the $ to spend again for a refrigerator. My refrigerator is so loud it has been waking me up for about a month now and I am sick and tired of it. Shame on Maytag for having such terrible customer service! I will never ever ever recommend a Maytag because this has been a nightmare!

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

I purchased this washing machine from Home Depot in 2012. I am amazed that it lasted this long after reading the reviews on here. It will not drain water, it will not spin. I see many customers bought the same washer and are having multiple issues. When will Maytag recall these machines? Overpriced and unfair to consumers to sell something that is broken or not reliable.

Refrigerator failed in less than 7 years. In August 2005, I purchased a new Maytag side-by-side refrigerator to match the Maytag appliances (stove, microwave and dishwasher) in the new house provided by builder. In October 2011, I called a repairman because of noise. The relay switch was replaced for $179. Now, I am told the compressor and defrost circuit board need to be replaced for over $700. I will never buy another Maytag appliance or Whirlpool. They make and sell crap and dont stand behind their crappy products.

Maytag Washer was bought on May 2010 for $746.29 and it broke down. It was used only twice a week. It now requires repairs worth $991.36. All Maytag reps say is I am sorry, there is nothing we can do. Isnt there a lemon law for major appliances?

I researched gas ranges for a few months before choosing our Maytag gas range - it was on sale when we ordered it and it arrived within a couple of weeks. We wanted to buy local and were successful with price matching the sale price. I would recommend this range as it functions great and we totally love the larger oven door.

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

Consumers be aware! Anyone who’s considering purchasing a Maytag Appliance I would highly suggest reconsidering! I bought a $2000+ Maytag fridge Model # MFT2776FEZ00 in March of 2017 and have had numerous repair calls on it: Several for ice maker not make ice, ice freezing in the bucket into 1 big CHUNK, water running down front of door on the inside and outside, to not working at all and ice maker needing to be replaced. Several calls for fridge not properly cooling (temperature was set at 37 degrees F but the temperature in the fridge is 55 degrees F - per 2 thermometers), food is spoiling. The back inside of “Temp Controlled Pantry” is freezing everything and whole back wall behind the drawer is frozen with 1-2” of frost and ice. Defroster is not working and again parts being ordered to repair an obvious issue with this model.I contacted Maytag and their response was “sorry, we can document the problem.” They will do nothing more! These Appliance companies are ripping off the consumers! Everyone passes the buck! Repairman says, contact the Appliance store you purchased it from, Appliance store says, contact Maytag, Maytag says it’s the repair companys issue.

I purchased a refrigerator 9 years ago and the ice maker stopped working. When the repairman took it out there was plastic peeling from the ice mold. It cost $261.11 to have the ice maker replaced and the ice maker he replaced it with has the plastic on the ice mold. He said that GEs ice makers do not have the plastic coating but Maytags still do. I called Maytag and spoke to a supervisor and they said that there was nothing that they could do. I am filing this complaint because I feel that consumer need to be aware that they are ingesting plastic that is in their ice. I feel that Maytag should compensate me for the faulty part and also eliminate the plastic coating from their ice maker. This issue is impacting many other consumers and they need to issue a recall on the ice maker and replace it for free for other consumers.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

I cannot control the water level which results in smelly and not very clean clothes. I follow all the manufacturers guidelines but after several washes, the smell comes back.

I purchased this machine (Maytag Bravos XL MVWX700XL2 ) about 18 months ago. I was so excited with the looks and the reviews I found on the machine at that time. For the first 14 months I was happy. All of a sudden, it has become the washer from Hades! It twists and almost ruins my clothing. Not to mention, I think it is permanent wrinkles that it puts into things. I washed our comforter on Bulky. The part that must have been at the bottom is completely wrinkled and it also wrecked all of the fill. This was a comforter that it is supposed to be fine to put in the washer. I am attaching pictures in which you can almost plainly see where the comforter was at the bottom. I had a serviceman out a few weeks ago. He said Maytag knows that there is a problem, however, there is no service bulletin that is out yet on it. In addition, he ran all of the codes and told me there is nothing wrong with my machine. That must be why I have to iron almost every piece of clothing in this house. Maytag will hopefully give me decent customer service on this, or I will come unglued. For the price of this washing machine, I expected much more.

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

Maytag water efficient, no central spindle top load. Clothes come out with scum on them. Really a problem on the solid darks. I have to scrub with terry cloth to remove. Maytag insists this is normal. Refused to honor warranty. Usually check Consumer Reports for quality and best buy. Energy/water efficiency is important. I like to have some control over the machine so that I can use it the best way for me. Such as soak. This machine cannot be manually controlled at all. Also it doesnt have a lint catcher, doesnt filter the wash or rinse water at all. All the lint and pet hair remains on the clothes or even gets worse.The clothes are not clean. I have no way to control the machine for my use. It may be water efficient but seems to use too little water to clean the clothes. Maytag wants to blame the EPA - This is irresponsible on their part. Its an awful washing machine and they made it. Maytag continued to insist that scum on the clothes was working normally. This scum was added by the machine. I used very little detergent; the clothes were relatively clean - just lightly wore a few days. They come out of the machine with streaks of white scum that I have to scrub off. The clean the machine cycle uses a huge amount of water. This is really DUMB: washing the machine instead of cleaning the clothes! Terrible! And Terrible customer service at Maytag. DO NOT BUY MAYTAG.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

Ive owned my Maytag Neptune front loader since 2003. Since then, the whites have either turned gray or yellow. Ive tried minimizing the use of Tide HE, maximizing its use, and I still get the same results. Can anyone please assist me with this major problem? Ive owned Maytag appliances since the mid 60s, and I know the quality isnt there anymore.