I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

I have had my refrigerator freezer for 2 1/2 years. It worked fine until about 6 months ago. The vent started freezing and then water ran to bottom of freezer and freeze. If I get this fixed, I hope that will be the end of the problem. I am going to defrost it the old fashion way to see if that works. I will never buy this product again.

Updated on 02/13/2021: Maytag stove purchased 15 years ago for about $500. Replaced mother board about 5 years ago which wasnt cheap, but otherwise, stove has performed with no problems and still looks and behaves like a new stove.Original review: Our 6-7 year old well cared for Maytag range oven recently stopped working. After a service call for diagnostics, it was determined the electronic module controlling the clock and all oven functions was dead. We were told by the Maytag service tech the module cost was 300$. That cost plus labor for less than an hour, plus the 60$ diagnostic visit came to almost 500$ which is close to cost of a new stove. The technician answered yes to my question, Do you replace a lot of these? He also said the cause may be power fluctuations making me think that surely there is a way to prevent this kind of failure. So, since the price seemed exorbitant, I wrote Maytag to inquire about causation/prevention, etc. I received a fairly prompt and polite reply with totally no explanation. I wrote another email with relatively the same results. I dont recommend buying an electronically controlled Maytag stove.

I spoke to Destiny today at the Resolution Center, she knew one phrase, its a low usage washer. I would reply, 3 inches of water in a drum does not wash my familys clothes. Every load is covered in white soap specks, whether powder, liquid or pods are used. Again, Id hear, its a lower usage washer. Ok, I got it.The machine has been cleaned with Affresh.This washer cannot clean a single shirt let alone a full load of wash. Maytag (actually made by Whirlpool) should be ashamed to produce such a shoddy product and expect to the consumer to keep paying for repairs. From reading the reviews on a couple of websites, consumers have to keep repairing this washer time and time again. Destiny told me she would send a technician out at my expense. The machine will be in the landfill on Saturday. Never again Maytag/Whirlpool.

I have gone several years with wasted food at random times because my Maytag refrigerator decides to stop cooling whenever it feels like it. This is a continuing thing that started since the appliance was brand new and it has never been resolved. Maytag claims that they cant do anything about my refrigerator. They can do what they want to. From my experience, I feel like the issue is that they dont care to make it right. I am finally fed up with this refrigerator and I am buying a new one. I can guarantee that it will not be a Maytag.

My front load Kenmore just fell apart. I guess Im lucky I have had it for 8 years and now its broke. I could fix it but thought it would be better to get a new one. I looked at all the reviews for front load washer and could not find one that had positive reviews. So I went with a top load. After reading all the complaints I might have made a mistake, but its too late now as it was delivered yesterday and now doing the clean cycle. Oh my…what junk they all produce now - a true throwaway society. My refrigerator is still working after 24 years what a gem of a product. Happy days.

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

The control board is not working on my 2 year old dishwasher. I now see this is a common problem with Maytag dishwashers. I have called to see if there is a recall on this problem and they said no. I have been told it can cost up to $500 to fix it so I guess it is a throwaway. I should have called when it was purchased as the digital buttons didnt seem right from new. What a waste of money and I will never buy Maytag or Whirlpool.

Not only does the water not drain properly causing an insane amount of stench of moldy water being trapped, but this washer has had nothing but problems since we got it. Error code after error code, problem after problem. So disappointed. My husband wanted an LG and I said it had to be Maytag because Maytag was the best. Thanks for making me a liar Maytag!

Purchased from Lowes October 2014, paid $680.00. Now needs $600.00 in repairs for new springs and basket rim according to a Maytag appliance repairman.Washer is leaking in the front left. Repairman thinks I need 4 new springs and a redesigned taller basket rim to keep the water from pouring out over it. Yes, it is 16 months old!! Ridiculous!

I purchased a Maytag refrigerator about two years ago because of the Maytag quality hype. The ice maker has been leaking almost from day one and I need to clear out the ice from the bottom of the freezer every few weeks. Now the thing has quit cooling all together. I contacted the Maytag website and they recommended a local authorized repair firm. I took a day off work to meet the service provider. After checking the fridge they informed me that the problem was with the sealed system and that they could not work on it, and that I would need to contact Maytag to get a real Maytag repair person to come and fix the thing (right back where I started). They were however more than happy to charge me $70.00 for a service call. I tried the Maytag 1 800 number which was a nightmare and it finally hung up on me. I then went back to the website and managed to get a service appointment in two weeks (had to wait for a Saturday appointment because I cant afford to take another day off work). I just hope that this time it will actually be someone who can fix the thing and not charge me just to refer me back to Maytag again. I am not happy with the so called Maytag quality or their BS methods for providing service. Caveat Emptor if you are contemplating a Maytag appliance.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

We are on our 2nd Bravos XL. The first washer lasted 6 years and there was a part going out that kept making it stop in the process. Basically the repair guy said it will just go out one day so it was up to us to repair or replace the machine. The machine didn’t have an agitator and we had been having issues with white residue on the clothes for a long time but thought it was related to the other part. So we bought a new one, with an agitator. It was the new model. We’ve had it around 6 months and we have lots of issues with the white residue. The only success we have with not getting white residue on darks is using deep fill and very little detergent. We use powder because the liquid makes dark spots on our dark clothes. So either way, there’s a problem. So we are using a lot of water when it’s supposed to be water saving. And we are using much less detergent that the company says. I think it’s the machine that has problems. I’ve read a long thread on Facebook and it appears that Maytag tells you to use Affresh regularly. It also says to follow their instructions. But everyone seems to follow instructions but Maytag takes no responsibility for their product. Makes me sad because Maytag was the best on the market at one time and we will never buy again. Our dryer works fine but the washer sucks. And that was a lot of money that I paid. I hope that Maytag decides to make it right and help their “customers” enjoy their products once again.

On August 25, 2011, we purchased a Maytag washing machine (Model Number MVVYC400XW2) at the Lowes Saugus, MA, store. Initially, we had no performance problems with it; however, on January 12, 2012, the washing machine wouldnt start. That day, I called Maytag for service on the machine, and it was fixed. Then on August 18, 2012, the same thing happened. A serviceman was called for the second time, and was repaired. Ironically, the Maytag 1- year warranty was expiring on August 24.Prior to the expiration of the Maytag warranty, I had been contacted by mail about an extended warranty plan, which I thought was being offered by Maytag, which it wasnt. The offer was being made by Federal Warranty Service Corporation. I purchased a 5-year extended warranty, expiring on August 25, 2017, the reason to have coverage for what seems to be a faulty machine. I would probably need it.Dealing with Federal Warranty has been nothing but grief. In 2012, the washing machine, had required 3 service calls, one with a Supervisor explaining my frustration with the number of service calls I have had made for the washing machine, but nothing has changed. Thus far in 2013, I have made two (2) additional calls for service on the same washing machine. Not only are there the numerous service calls made but the inconvenience of not having a washing machine, and the additional costs for outside laundering, during that time has to be taken into consideration. Additionally, my wife is 68 years old, and Im 71 (72 in August). Going up and down the stairs to the basement isnt something we should be doing, especially to find an inoperable washing machine.

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

We bought a new commercial Maytag washer. It’s deep, it has the agitator, suppose to be the top of the line. I can do sheets and the top ones are dry when done. It doesnt get clothes clean especially if they are really dirty. So I add water to this wonderful machine——anyone wanting pictures of finished clothing I would be glad to send to you. Dirty jeans come out dirty jeans. If I forget and don’t add water it’s worse. So I watched it. It fills up to maybe halfway on clothes and this is on heavy soil and deep fill. I complained about it at the store and was told “he had one and it did fine” and you can’t get any that do any better.

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

We have to rinse off any food particles before we wash or it may not wash off. So I use plastic wiper before we load. Only 2 of us so items may sit 3-4 days before we run our Maytag dishwasher.

I bought my refrigerator in May of 2012. Brand new from Home Depot. It is less than 3 years old. Now it is not working. I did not purchase an extended warranty. I never thought in less than 3 years my fridge would stop working. I called Maytag, first question from them was about warranty. So I knew I was screwed. So, basically for $300 they would come out and fix the problem. I only paid $800 for the fridge. I am lost as to why in 3 years my fridge is broke?? Makes no sense to me. So I paid a tech $100 to tell me what was wrong with it. The evaporator is leaking. It is leaking. So the evaporator is bad and I cannot fix myself. So for another $300 they would fix, so a total of $400 in an $800 fridge.I am pissed. I remember my parents having a fridge for over 25 years. Why does Maytag not take responsibility for their problem. The products we buy should last longer than 3 years. It is just a way for them to get us to buy another product. So needless to say, I am one pissed off customer. So let the emailing and letter writing begin.

I purchased a Maytag Bravo washing machine item # 26 23872 for $617.69 on 11-23-11 and it was delivered and set up on 12-02-11. My problem is if you have dirty sweaty clothes, you cannot get them clean with such little water. I used the HE detergent as directed. I talked to a woman at the local Sears Appliance store this morning, 7-11-12, about it. She said I need to use Affresh. So I did clean my washer but with a similar brand and my clothes are still stinky. I have even washed an empty load or two with bleach and hot water. I make sure I wash with hot water and completely dry my clothes.When you take a bath and dry yourself off with a towel, it smells like a musty basement. I am allergic to mold. I cant even take a wash cloth, get it wet and wash my face without wanting to throw up from the smell. I have had guest comment on the towels as well. Its embarrassing. The problem is you cannot clean something with an inch of water in the machine. I am 58 years old and now have to do the wash. I went to the store and asked if we could return it for an exchange or anything like a discount on a new one and she would not budge. She said it had to be within 90 days but 90 days was in the middle of winter and I was not having dirty sweaty clothes from doing outdoor yard work.Now that summer is here, 7 months later, my clothes have been smelly for a few months. I cant take it anymore. I showed the woman that I had been to Lowes and had an estimate of 10% off with free delivery, set up and haul away. She said she could do 15% but when you add on the delivery fee, it was higher than Lowes. I purchased my whole upgraded kitchen stainless steel appliances for about $7,000 and this set of washer/dryer but Sears could not help me out? What a disappointment that a loyal customer such as me could not at least get free delivery on a new washer. I went right back to Lowes and ordered the same machine I wanted Sears to sell me matching Lowes price.So now, I am stuck with a 7- to 8-month-old machine still in the one year warranty that is like new but is a worthless piece of junk as my clothes all stink. Run, dont walk if someone tries to sell you a low water HE machine. I tried sending this letter to searsinfo.com corporate office and it is rejected even though the website gives you that address.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

Electronic control board fried after 3 yrs on Maytag Gemini range - certain buttons on control board would not set for ovens. Called Maytag, said was not covered, past 1 year warranty. Recommended repair shops, all overpriced. The piece cost between $300-500 for a 3 year old stove. Cheapest repairman wanted 90 to install piece. Ordered piece online and replaced it myself with help from YouTube video. Maytag has lousy repair records lately. Of 4 Maytag appliances purchased in 3 yr kitchen remodeling… already had issues with 3 of them. Do not recommend Maytag anymore!

The machine has left pin-sized holes in finer clothing since we first used it. I had purchased the extended warranty so they were called out to repair the issue four times during the warranty. They replaced the drum, but I still get holes. I think it is because there isnt enough water to rotate the clothing and it rubs repeatedly against the same spot on the other clothing. I have a see-through lid and you can see that the clothing just moves very slightly in the same position. I separate all clothing that has a zipper or any trim that may rub against the finer fabrics, but I am still getting pin-sized holes. We requested compensation or a new machine. They extended the warranty. We have replaced enough clothing that we are now buying a new machine. It will NOT be a Maytag.

Why is it when you wash dark clothes they come out with white spots which looks like soap. I have put very little soap and it still appears. I usually wash in cold water so I tried warm water - same result. I have had a Maytag for a least 40 years never had this problem - what is it I am doing wrong? I have to wash and rinse at least 2 more times. I would appreciate a answer so I can fix this.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

We purchased a front loading Maytag washer in January of 2011. We purchased an extended service plan in January of this year. I noticed a very loud noise and inappropriate operation during the spin cycle. I called the service plan, who contacted a repair service to come out and check my machine. I was told that there was a major problem that would be very expensive to fix and that the Assurant company would contact me in a few days. The company called and said that they would give me 75% of the value of the machine ($650) because fixing it was not economically feasible. I said that I did not want the money; I wanted the repair that I was guaranteed by my service contract. They referred me to the small print on the back of the sales letter. When I asked about any manufacturers warranty from Maytag (the washer was less than 2 years old), I was told that they had nothing to do with the manufacturer and I had to take that up with them. When I tried to call Maytag, they were decidedly unhelpful and referred me back to Assurant.There are several issues related to this event that I wish to complain about: 1) How dare a major company sell a thousand-dollar appliance that becomes unrepairable in less than 2 years and take no responsibility for the breakdown? There was obviously a defect in the machine that took over a year to show up (we are a household of 2 adults and did not overuse the machine). 2) How could a service contract issued under the Maytag name not be aware of parts covered by the manufacturer? 3) Should not the buyer of a service contract bearing the Maytag name be informed that it is not Maytag (the manufacturer) that is guaranteeing the product, but a third party?4) Should not the seller of a service contract be required to display the terms of the contract in a prominent place? The sales letter specifically states Repair or replace - If we cant repair your appliance due to a mechanical or or electrical breakdown, well replace it. The limits of coverage are in fact given in small print at the back of the letter and are on the contract, but this contradicts what is displayed prominently on the promotion letter. This is false advertising and should not be tolerated.

Very disappointed with my 2014 purchase of model MDB8959SBS3 dishwasher. In fact it is no longer in service. We used the dishwasher approximately twice a day. The wheels on the pull out racks starting falling apart in the first 6 months. Then the soap dispenser failed. It would not shut. We replaced both the wheels and the dispenser only to find ourselves with the exact same problems in a matter of months. My hubby got really good at fixing both of these items. The final straw was earlier this year as when we turned it on the motor/water pump started making a screeching sound. Never had to replace an appliance that was only four years old in my lifetime. Just very disappointed with the quality of Maytags dishwasher.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

I just found this website & do not have my model info with me. But we have bought 2 Maytag refrigerators since 2001. We still have the 2nd refrigerator but I want to replace it as soon as we can. They were different models but had/have the exact same problem. They freeze up into sheets of ice and then leak puddles of water on to the floor. Makes me mad when I see their ad about how great their product is - what a load of crap! My first refrigerator was a General Electric; it was still running after 19 years when I left the farm. I still have my 2nd General Electric refrigerator (18 years old) down in my family room - running like a top! NOT EVER GOING TO BUY MAYTAG AGAIN!

Maytag may have pay to replace defective controls. 1-866-931-7384 is the number to call. I have owned my maytag dishwasher for about 18 months. Its control panel was never great, but now my dishwasher wont work at all. Apparently, the tiny inside the control panel rust away because they arent sealed.

I dont even bother repairing those things. Customer calls and I say, Sorry, those are worthless. I did try but gave up. Buy Speed Queen. Traditional, heavy duty, with three-year warranty. Whirlpool who owns Maytag doesnt give a crap. They want their warranty repairmen to pass drug tests but no longer give appliance training. Speed Queen is built in Wisconsin. Who knows who is building the Maytag crap. Another customer had a similar problem with Maytag stove, 1 year old. Whirlpool and Menards said, Sorry, you didnt buy the extended warranty. I have conversations with just about every customer about junk appliances these days. Try to find used 20-year old Maytag for quality. Good luck.

Does not clean properly! Water level is too low for clothes to move around properly. This appears to be a very poorly engineered product. We have had Maytag products for many years. The only good thing I can say about this product is that it beats a scrub board. Would not recommend Maytag product to anyone. Looking at other complaints it appears that Maytag is doing nothing about this. Will try to sell this at a yard sale and hope no one asks my opinion. Then go buy something that works.

We bought a Maytag dishwasher on 9/22/2012. Model number MDB7759SAB. Within the past couple of months, it has been very temperamental. The control panel started beeping continuously and some of the functions wouldnt work anymore while others continued to work too well; in that the dishwasher on occasion would rewash several times without anyone starting the machine again. The dishwasher also started leaking water... As of yesterday, the dishwasher control panel stopped responding and then out of the blue, the dishwasher turned itself on in the middle of the night! We called customer service and they said they could send a repairman out for around $89 and then we would have to pay for the parts needed and the cost of labor. After reading many reviews sounding exactly the same as mine, my husband and I are against repairing this lousy machine. Its absolutely ridiculous for a dishwasher to quit unexpectedly like this. Our question now is, which brand to purchase for our next dishwasher? No more junk please!!

This is probably the worst place ever to buy any appliances. They are extremely unreliable and the technology on them sucks. If you wanna buy new appliances I highly recommend you spend your money elsewhere. The customer service is extremely horrible and is a disgrace. Shame on this company. They lie about when they will repair your stuff too, so dishonest and I hate this company.

The washer does not wash the clothes, period. It leaves dirt and soap in the machine along with the unwashed clothes.

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

My washing machine is 2 1/2 years old. It is not overused, just 2 people in the household. Maytag wanted to sell me a contract for $320, I declined. After research I see that this machine has many complaints against it. I bought Maytag because they never need repair. I would like Maytag to fix this machine without charge or recall the machine. From what I have read, these machines are defective. The electronics are failing at 2 to 3 years.

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

Have used for several years, no problems. Not even with ice maker. The black color is good and matches other appliances. I like the pull out drawer for freezer items. However, the filter is very hard to change but other than that everything ok.

This machine does a great job at cleaning clothes. The clothes are always great in color, and removal of removable spots. The cycles are not too long and the machine is not noisy. Machine is nice looking and water cycles can be normal or large.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

My Maytag washer has been a problem since we bought it. Maytag washer has been repaired 3 times. Stopped working again. I am 78 years old, I have take myclothes to the laundry mat. First, waiting for the repair then waiting for the parts. If Maytag stands by their product they should replace it.

Purchased Maytag Model MVWB865GW0 Ser# **, had it ONE year, circuit board and switch have gone bad, will not turn to change the type of wash cycle and the lid will not lock, which makes the washing machine not start to wash. Contacted Maytag to request a service call, per the service team the circuit board will cost $300, plus a switch $75 and Labor $100 plus tax. We will be better off buying a new washing machine! We should not have this high cost within ONE year of purchasing! Will not purchase a Maytag again!

I purchased a Whirlpool oven. It is still under warranty at present. I used the self-clean oven feature just before Christmas, it wasnt that dirty but I wanted to have it clean for Christmas. The glass panels on the door had no stain or grease on it, until I used the self-clean feature, and now there is black staining inside the glass. This oven is not even 9 months old, and you cannot clean in between the glass. My second complaint which I believe is a very poor design on Whirlpool’s end is that the steam vents are very sharp. When I went to wipe off the black splash panel just under the vent tube, I cut my baby finger twice!!! And it is impossible not to slice your pinky. I have been working with Whirlpool since this happened, and they finally issued me a new stove. I was to go back to where I purchased this product and pick another stove. So I did this yesterday and checked out all the Whirlpool stoves because the store says I have to purchases a Whirlpool. But every Whirlpool model has the same sharp steam tube vent, and I am presently waiting for the store manager to speak with his higher ups to see if they will let me pick a stove made by a different supplier. I’m actually really shocked to learn that this could end up being a battle especially after I took the manager to every stove in his store made by Whirlpool and showed him each of the vents and just how sharp those vent tubes really are. You would think he would want to be aware of this and deal accordingly. So I post this to warn any potential customers of Whirlpool to check that steam vent on the left side of the stove, and stay away from it as it is very sharp and you can’t help but cut your pinky finger when you wipe across the stove.

I have been the latest victim in purchasing a Maytag Refrigerator. Something needs to be done about the defective products they are putting on the market. I received 9/7/13 (yesterday) a new Model FW: 555 Complaints and Reviews about Maytag Refrigerators bottom freezer refrigerator. After being plugged in for 3 hrs, the temp was 60 degrees.. After 8 hrs same and 24 hrs same. I lost everything because of the defect. I notified the store 3 hrs after purchasing it and because I had it delivered on a Saturday I have to wait till Monday to get this resolved. I want everyone to read before buying a Maytag product.

We purchased a home one year ago. It has all Maytag appliances that were anywhere from one year old to two years old. The Neptune LE washer is not working as of today. This washer is supposed to be the top of the line, and because it is almost three years old, it is no longer under warranty. This washer will fill with water but does not spin or rinse the clothes. We paid a lot for this home and were so happy to get appliances that were all practically new. Now, we refused to have a repairman come and charge us lots of money to fix a washer that should not be broken. I have had washers run for 15 years and that was when I was washing clothes for 6 people, including cloth diapers for triplets! I will not buy any Maytag appliances. I will be getting an Amana or a Sears brand. Please, no one go buy a Maytag appliance.

We purchased a Maytag Bravos washer & dryer in September 2012 and 2 1/2 years later March 2015, no heat. We called a repairman and he said heat element went out. When researching this problem online I was shocked how many people had the same problem as we have. It cost over $300 to fix and I am concerned that it will just break again and again after reading these reviews. I think that a class action lawsuit may be needed so that this unfortunate situation does not continue to happen to other consumers.

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

Maytag Oven MGR8670WS1 - Purchased in the Fall of 2011 (along with a fridge... also faulty the freezer stopped working within a year). Ive had the oven stop working twice (in 2012). This week (spring 2014) would be the third time. It seems to be a faulty ignitor already replaced having to be replaced yet again. I have never used such faulty appliances EVER and never AGAIN. This is absolutely ridiculous.

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side

Owned my Maytag Maxima front loading HE washer for just under 2 years. Went to turn it on one day and got an error code that I later found out meant the computer board went bad (a very costly expense). I called Maytag and explained that a $1200 washing machine should last more than 23 months and if they stand behind their products they should do something to cover this repair. Even after speaking to a manager they told me too bad they couldnt help me. But they would be happy to sell me a $350 extended warranty.... Never again Maytag/Whirlpool!

After only 2 years my microwave stopped working. Now I can purchase a new warranty which is just as much as a new microwave, have somebody come out and fix it, or pay a service charge which is just under $100 and does not include labor and parts. I figured out now why nobody calls the Maytag repairman. We cant afford it!

We have a similar problem to the others who gave reviews on their still NEW Maytag refrigerators. Ours isnt even four years old and several weeks ago we started smelling a chemical odor which then permeated all of our food in the refrigerator and freezer. We didnt buy the extended warranty because we have owned a few refrigerators and all have lasted just fine for 15+ years with no problems. So I called Maytag. They said for a charge of $369.95 they would schedule a repair and would cover the service call, parts and repair and provide an 12 month warranty. If the service call results in an inability to repair the refrigerator, they will refund the full amount of $369.95. So I asked if Maytag would then replace the refrigerator, and the rep said we have to start with the service call before they would discuss any type of refund or replacement. Im angry and disappointed in Maytag. Its a good thing we have a spare refrigerator in our basement. What a hassle! Weve already had to throw away over $100 in food that picked up that horrible odor. Shame on Maytag!

I have been a Maytag customer for many, many years. In November, 2014 we decided to buy a new matching pair. No problems with dryer but the washer has been a nightmare from day one. Have had at least 5 service calls (lost count). The washer constantly smells. Clothes are not clean. Have to buy and run Affresh tablets weekly. Spend more on wash machine cleaner than laundry detergent. Funny thing is Maytag/Whirlpool makes the expensive cleaning tablets. The customer service at Maytag has not been helpful from day one. They recommended I buy an $150.00 extended warranty. Stupidly I agreed and regret doing it. They still have not fix the machine under the one year original warranty. NEVER BUY A MAYTAG BRAVOS WASHER.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

I bought a Maytag dishwasher Model MDB7749SBW3 from Home Depot 6/2014 and by December 2015, the touch panel was going crazy! Ive read a lot of reviews and this seems to be common for Maytags. It would cost me almost as much to have this machine repaired, with a service call and the cost of a new panel, as it did when I bought it. When talking to an appliance repairman, he informed me that Maytag and most all the major brands are now owned by Whirlpool and that they are basically junk--not meant to last more then 1-3 years! Where are the recalls and how do we get a recall started?

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

We purchased the Maytag Bravos XL MCT washer and dryer in July of 2013 and have been completely and totally dissatisfied with every use since. We immediately contacted the store where we purchased them and were told we had to contact Maytag. We contacted Maytag on numerous occasions only to be read ridiculous solutions from a notebook that were no different than the instructions in the users manual and never worked. We had our first set of washer (with agitator) and dryer for 23 wonderful years. The washer absolutely does not work. The decision to remove the agitator and reduce the water levels is absurd. The soap does not get distributed, the lack of water causes loads of clothes or sheets to get rolled up into tight balls with no hope of being cleaned, and the spin cycle is so powerful it rips your clothes apart unnecessarily. The dryer is smaller than the washer and cannot handle the same size load the washer can put out and typically requires more than one cycle to complete a drying. All in all this has been the most painful experience we have ever had with any appliance. We are completely dissatisfied with both the store where we purchased these units and the complete and total lack of response from Maytag after requesting either of them to take back these units or make some equitable adjustment so we could purchase different units. We have reached a point where we will most likely store these Maytag units in the garage and purchase a new washer and dryer, being forced to accept the financial loss.

After only 4 years, this washer stopped spinning. Called Maytag support (Ha! the ads show the Maytag repairman sitting by a non-ringing phone) I had to wait 20 mins to get through. Only after paying for a service call would they be able to determine if this problem was motor-related. In reading reviews (which in hindsight I wish I would have done prior to purchasing) this is a common problem and is related to bearings going bad. Pay for service call vs buying a non-Maytag product -- will set this out by the curb and buy a different brand.

We purchased the Maytag dishwasher model # MDB4949SDZ almost one year ago. Since the beginning there has been a smell to our drinking glasses when we put drink in them...smells like boiled eggs. We have always used Cascade dishwasher pods, but suddenly our dishes were being left with a gritty feeling film on them and I had to run them under water to rinse them after taking them out of the dishwasher. This model showed on Lowes website that it has a food grinder, but it cannot even get rid of a single kernel of corn that might get left on a plate. After a load is completely washed and you open the door, there is a strong smell of detergent. If you run an EMPTY dishwasher with NO soap it creates an abundance of suds like there is still soap all in the tub!!The repairman came out and called Maytag and they ran a diagnostic check on it and it said everything was okay. He said to run a cup of white vinegar through it and I did. It didnt help. Still lots of suds being produced when I run a cycle with NO dishes and NO soap!!! He said the food grinder doesnt actually grind or dispose of small particles of food, just grease!! What?!!!! We had to PAY $92 for the service call even though it is still under warranty just because the repairman and the Maytag guy on the phone couldnt figure out why this dishwasher is a hunk of junk!!!! Also, the top rack has clips on the side to lower and raise the rack. The outer sides of the top rack will only hold smaller glasses because these clips get in the way. I hate this dishwasher so much!!! My 18 year old Kenmore ran like a charm until Hurricane Harvey flooded our house. I will never buy a Maytag appliance again!!!

I agree with everyone one else and their experience with these washers. I took advantage of a credit for those replacing old washers with new HE washers. IF I COULD ONLY GET MY OLD WASHER BACK!!! Its only 2 years old and it sounds like - what others have said, like a B52 taking off (during the spin cycle). I dont have rust spots inside of the machine or out so Im not sure what the issue is but I really dont want to invest in a couple hundred of dollars to this thing. It stinks, doesnt clean well and now this! VERY disappointed...VERY. As a single mom, the thought of finding money to replace something that is new just disgusts me! Nothing like the old washers that last for 18+ years. Nice Maytag I will never purchase another product of yours and will spread the word!

I purchased an automatic dishwasher for $660.00 on or about Aug of 2007 (Mod #MDB6759AWS3 ser # NY3417703). It was a model about to be discontinued however still carried the full one year warranty. After install one year and 28 days it failed. The tech described a faulty computer board and a replacement cost of $885.00, a cost of $215.00 more than it originally cost!! They did offer a warranty of one year after we installed the new part but at a cost of $215.00 more than we originally paid! Maytag promotes their brand as reliable. However I dispute this claim.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

My wife and I purchased new Maytag dishwasher in 2011. Worked well for 9 months and then control panel went out. We bought a Sears with 1 year warranty. Sears fixed but then 2 more repairs followed with blown fuse and pump motor went out. We knew this was a lemon so we purchased an extended 3-year warranty through Maytag. Well the unit only works for a month or two then we are constantly calling for repairs. We just had the pump replaced a 3rd time and yep you guessed it the unit is loud again so here comes repair 15. The warranty contract states that if the same part fails 3 times, Maytag will replace the unit new one time and voids any further repairs. My wife and I are very frustrated and lost all confidence with the Maytag company. Our old one lasted 14 years and this new one is a piece of junk. The company reviewed my request of unit replacement but was denied for whatever stupid reason. This unit has over 5000 dollars worth of repairs not counting the lost time of appointments waiting for the repair. My wife has had to stay home and wait for 4 to 8 hours an appointment. She has many other obligations to do with her time. Its sad that Maytag does not stand behind their product. Its my conclusion that this company does not want to sell good product, they only want to sell extended warranties. Your products are not reliable if you have to offer warranties. I would like to see if I can get to repair 30 before my warranty expires by March of 2015. Maybe I could then see if 30 repairs would make the Guinness Book of Records on the most repairs done on a dishwasher with extended warranty. That would be something the company could be proud of dont ya think.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

Maytag Washer 2016 HE top loader. This washer is horrible to use. I hate everything about it. After your clothes are put into the drum and you close lid to start here is what happens EVEN though I select deep water: it puts small amount of water in and then it agitates the whole big load. This is so stupid! Can you imagine a large load of your clothes agitating with a very small amount of water in the drum?So to get around that problem, you have to push pause button and shut the lid after your soap, softener and then listen until that first amount of water fills and agitates, then you have to push pause and quickly put in your clothes. Then you shut the lid and again push the start button so it will fill with more water. Then if youre lucky in at least an hour your load is finally finished. I hate this washer. My boyfriend bought it and I asked him several times to PLEASE return it. He didnt so now were stuck with it for God knows how long. The one good thing about this is I will know to never buy one of these for my house.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

We purchased a Maytag MDB7749SBWO Maytag dishwasher. Suddenly the control panel does not work. Trying to find out why I found that there are thousands of complaints about this known defect with water and steam getting in and corroding the control panel. Shame on Maytag for continuing to sell these without fixing the problem. I expected my dishwasher to last many years based on the Maytag reputation instead I need to replace it. I am not going to spend the money on a repair with a machine that will have the same problem again according to other consumers.

On May 23, 2009, I purchased a Maytag bottom mount refrigerator even though I knew that Maytag had many problems with this product and others. I innocently thought that by the year 2009, all their problems would have been taken care of - I was wrong. On April 2, 2011, the freezer part of the refrigerator was not defrosting. I had to make a service call to replace the control board. On March 3, 2013, the regular part of the refrigerator was not cooling. I had to make a service call to replace the control board.Complaining to Whirlpool is a waste of time. The best answer I have received is, I am sorry. There is no end to the garbage Whirlpool is manufacturing and by my experience they dont care. Why dont we, the consumers, hire a lawyer and start a class action suit to let Whirlpool know we are fed up with being ripped off?

Does a good job of cleaning but takes much longer to complete. Pretty much standard features. Has rinse only cycle, air dry only cycle, and cycle for pots and pans. Top rack had special holders for long stemmed glasses which I dont need. Standard size. Same size as my Kitchen Aid. White, front load, no special appearance. It takes much longer than my old dishwasher. Also the soap dispenser broke after 2 months and had to be replaced. It requires that two buttons have to be pushed to start. My old one only required one. It does a good job of cleaning.

Maytag Top Loading Washer-We bought this machine a little over a year ago and it is one of the worst products weve ever purchased. More often than not clothes barely get wet and then wad up into a twisted mess which stops the machine. Ive had to restart a load over and over. And, the clothes are not as clean as they were from our former Maytag washer which lasted 14 years. The new washer has to be cleaned at least once a month or it smells. We purchased this washer from HHGregg and they are no longer in business or I would complain to them about selling faulty products. I dont know why the manufacturer decided to remove the agitator from new models. What a mistake! We have decided to get rid of this washer and buy another brand. No more Maytag (or Whirlpool) products... ever!

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

I purchased this five-burner gas stove two years ago. I have this stove repaired three times. The first and second problem with the stove is when I turned on the oven, it would never click on. This was a month after I purchased the stove. They sent someone over to correct the problem and that did not work. The third time someone came. He changed something in the oven and it started to work. After that, I continue to have trouble with the oven. When I have the top eyes on, the oven will not work. When I only turn on the oven, it will go to 350 only. It will cook for an half hour and then cut off. I smell gas in my house and my food is smelling like gas. I have stop using the oven. I did not purchase a stove to not use the oven. This is totally ridiculous!!! I am tired of this situation. Maytag needs to recall these ovens, so I can purchase an oven that works. I have thrown food away because it smells like gas - because the oven will cut off in the middle of cooking. I am very tired of this situation and when you call Maytag, their customer service is terrible. I will never buy Maytags products again. Please help.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

Maytag dryer MEDC215EW - This dryer does not dry the clothes without many wrinkles. Sheets just ball up with the inner sheet a mass of wrinkles. Small loads just flop from top to the bottom of the dryer, falling in clumps. I have gone back to having to ironing. Very disturbing!!! I would not recommend this dryer to anyone.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

We moved into our first house just over two years ago and decided we needed to get a new refrigerator. We did a ton of research online, reading reviews, etc. We found a few not so great complaints regarding Maytag; however, we took our chances. (Note that we live in a house built in the 40s, so the fridge space is small and we needed a fridge size that is smaller than normal. We didnt have many options.) Well, a little less than 12 months later (yes, luckily right before the warranty expired) our ice dispenser stopped working properly. The mini-ice door would not close properly, resulting in a lot of frost in where the ice door was located. (There was so much we couldnt open the freezer door. It would get stuck.) So, we called out the repair guy and he said he had never seen this issue before and basically had to replace the whole flap and parts. Sweet. It was fixed and cost was covered! Well, about 5 months later, it happened again! Ah, they got it fixed yet again. Well, another six months later and after the warranty expired (lucky us), the fridge completely stopped cooling. (And it just happened to be Halloween, not a great day for a house issue.) So, we had to remove all our perishable food and place it in a cooler (which works hundred times better than Maytag products), and move all frozen food to a family members house 15 minutes away (luckily!). We were also super lucky we found a repair company that could come out at 5pm the next day, which happened to be a Friday! Awesome company (Conners Repair in Metro-Detroit). He concluded the defrost board was broken, meaning it was freezing and creating frost and then not defrosting, clogs the vents and not allowing circulation to occur. He was shocked when he found out we only had this fridge for 2 years and said this is something that normally happens in 20-year old fridges. I then decided to call Maytag and nicely requested a refund for the issue. I was told no due to the warranty expiring and also because we didnt use a Maytag repair company. I didnt want to wait a week as I thought this was something that needed immediate attention. I also am not sure why it matters who you get to fix your fridge. I have an invoice for proof of the issue and the repairman even said hed call to verify the issue. I don’t understand why I have to pay for something that was not properly produced, and not to mention the time out of my schedule to deal with Maytags issues. I now know not to buy any Maytag products due to the lack quality. I guess I learned the hard way.

The washer is making loud noises. I had a repairman out and he said the transmission was shot. This washer is only 7.5 years old and the set I had before lasted 19 years. It also was a Maytag. My mother, sisters and aunts have always stood by Maytags and I am disappointed that this washer being 7.5 years old is shot. The dryer to the set is working great!

Bought top of the line Maytag Commercial Technology washer because it was supposed to be the most advanced on the market. My experience has taught me that advanced does not equate to efficient, effective, and expedient. The washer settings for an average load (sheets or towels or clothing) is about 111 minutes per load (nearly 2 hours!!). To adjust to what would be a quick wash is about 25-30 minutes BUT the washing part of that is only about 5-7 minutes. I feel like a Pioneer Woman because I must spend most of a day to run four (4) loads of laundry (sheets, towels, dark clothing, white clothing). This is extremely frustrating!! I am sorry I purchased this product.

Had a problem with the control circuit board on my 6 year old refrigerator. Had it serviced and found that the problem was common, the main circuit board needed to be replaced. The service person advised me it wasnt currently available from his supplier. I call Maytag and they said it was back ordered from their parts source. When asked for an availability date, I was told the date was unknown? I started a search for the circuit board and found it was indeed a problem for many many other consumers who owned this model refrigerator. Lesson learned: Maytag is no longer a good brand to own.

My husband and I purchased both a Maytag washer MVWX655DW1 and dryer MEDX655DW1 less than 3 years ago from Sears. We had both the washer and dryer professionally installed. Yesterday, we had an authorized service man come in and look at the problems we were having. He told us our Maytag washer would need a new gear case and gears costing $750.Our Dryer, same age, needed a new cycling thermostat. He said it was due to not cleaning out the lint trap. My husband and clean the lint trap after every load religiously. He said there was a pile of lint built up in the dryer. I could only think this would be a design flaw. To repair the dryer it would cost $350. The grand total to repair our Maytag Washer and Dryers would be $1100. We paid $1082.38 at Sears for both. The only thing Maytag offered to cover was a part for the washer which would cost $640 and we would need to pay the extra $110 for service in addition the $150 diagnostic charge, due to use being out of our one year warranty.We decided to not fix this machine to avoid similar problems in the future. I talked to customer service and asked them to cover the diagnostic charge instead of sending the part, which is far more costly. I got the runaround and 3 rejections before they finally agreed to pay for the diagnostic charge. My husband and I are extremely disappointed in this experience. We currently own a Maytag Microwave and Electric Glass Top Range. We will never buy Maytag again. Our Stove is also lacking. We have the AquaLift cleaning stove. The AquaLift technology does not work.

After replacing plastic parts that spin tub twice, now the computer is wasted. Purchased not even 3 yrs ago, now I have to buy a new washer because the computer system is not covered under warranty. REALLY!! The most expensive part. Not worth fixing. Never washed really dirty clothes when it wasnt broke down. Agree with the class action I would be in. Dont buy people and now I am off to pay to wash my clothes.

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

Clothes are never submerged in water. Clothes come out worse than when they went in. Every review and complaint mentioned is dead on! This Bravos XL is a piece of crap. Stay away from lying salesmen from HH Gregg. And stay away from Maytag. Perhaps we should all get together and file a class action lawsuit! And donate all monies, washing machines and dingy clothes to charity!

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

I purchased this Maytag Bravos Xl Top Loading Washing Machine approximately 2 1/2 years ago. It broke down shortly after the 1 year warranty was up and cost me $300.00 to fix. A bearing had broke and needed a service call to repair it. Well, I paid about $800.00 to begin with, so decided to fix it. Today it started draining water from bottom of it. I call Maytag and after a 20 minute wait on the phone because they were having higher than normal call volumes! They cannot help me, other than to charge me for yet another service call and perhaps a repair. Whirlpool/Maytag makes a high priced money pit of a washing machine! Dont waste your money!

The digital display on our Maytag Washer model MVWB765FW, bought 3/22/2017, failed overnight (whilst the machine was not operating) after 3 1/2 years. A reputable firm came out and diagnosed the problem, their report concluded that the Control Board had failed and needed replacing: they provided a verbal quote of $525 [ ! ] to do that. The machine cost $600 and based on the expected life for washers (per Consumer Reports) of ten years would have a maximum residual value of $420 based on straight-line depreciation. The retailer from whom we bought the washer told us that he had contacted Maytag and asked them what they were prepared to do about this failure: a week later and absolutely no response from the manufacturer. Apparently Maytag has no concern for their customers or their own reputation. We made the mistake of buying this machine based on Maytag’s reputation and a ten year warranty which appears to cover only parts unlikely to fail! NO MORE MAYTAGS FOR US.

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

Approximately one week ago, the display on my fridge began to flash and ice door flap continuously opens and closes. Upon researching the issue, it seems to be a very common issue and a known defect. One in which was apparently a recall at one point. I was told by a Maytag representative that the recall was from 2007 to 2009 and has since expired. Expired? Its a known defect and should be the responsibility of Maytag to provide the parts and labor to repair the fridge. I asked for a supervisor and was told that one would contact me within 24 hours. Well, about a week later, I never received that call so I called Maytag again. This time I was told by the maytag representative and a supervisor that there was no recall and that it was a Quality issue. A play with words, in my opinion. Anyhow, regardless of the title the issue was given, I was told I would be responsible for the repairs and costs. I attempted to look up the recall on Maytags website and had seen the last two letters of the serial number to my fridge listed under the recall, but when I tried to investigate further, the site referred me to the 800 phone number I had been calling. Now, had this been an issue that was not a known defect and apparently a recall, I wouldnt be writing on this site right now. But, because it is a known defect that maytag is aware of, I think its Maytags responsibility to pay for the parts and labor for my fridge.