I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

It looks big, but is small inside. Its hard to put in several large items. The water filter broke and too expensive to fix. I like the double doors and ice maker. I dont like the freezer drawer. It wont stay open to clean.

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

CONSUMER BEWARE! The Maytag Bravos X is without equal the biggest disappointment I have ever had the frustration of using. What a rip off! Water goes in, water goes out and it makes A LOT of noise. That’s it! (That locking lid should have been our first clue.) Specifically, a normal load takes one hour. What you save in water you pay double for in electricity. If you place a folded pair of pants in the washer that’s the way they come out; folded. Two twin sheets and a small blanket come out of the washer with dry spots every single time. If I use liquid fabric softener the clothes come out spotted with it. And it is louder than the train. You would be 100x better off purchasing a washer at a yard sale for $25 than to throw your money away on the Maytag Bravos X. DON’T DO IT.

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

Maytag Model #MBR2258XES refrigerator purchased May 2014 from Home Depot. Problem #1: Freezing in refrigerator compartment (frozen vegetables). Problem #2: Water leakage on floor from defrost. Wood floor is/has expanded and may now be ruined. This model is now discontinued. Looking into contacting an attorney.

Maytag Frontload washer MHWE300VW12 - I bought the washer and dryer in 2010 through Lowes. In Dec. 2012, it started making a loud sound when it would be in spin cycle. I called for service. When the repairman came out, he said the rear seal/bearing was bad and has gone out. The part and labor cost would be $1,184.36. Come on, are you flipping kidding me? Thats twice what I paid new for the washer. I bought them for the Maytag name. If I would have known it was a Whirlpool, no way I would have gotten them. My mother had a Maytag set that lasted 30 years. That explains why they dont show the commercials with the Maytag repairman that wouldnt have anything to do. Also, when the parts came in, they were Whirlpool parts. What a scam. Just more junk for our landfills.

I have a Maytag Bravo washer which I purchased from Brubaker Appliances in Lancaster, PA four years ago. I also purchased from them an extended 5-year warranty. I have this installed on 2nd floor with a drain and a drain pan The drain pump got a hole in it and leaked water all the way down to the basement, over $6,000 in damage. The drain pan and drain didnt work because the Maytag has a noise barrier on the bottom and when that was soaked with water, it sealed off the drain pipe. Also, when I contacted repair at Brubakers, they replaced the drain pump but then informed me that it wasnt covered because penny got in there and that is neglect. $332 later, I was told that the extended warranty covered everything and also no one will take responsibility for installing the washer so that the drain pipe could be blocked. I will never purchase a Maytag again or anything from Brubaker Appliances.

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

MFF2558VEM0 - Had the same problem repaired less than years ago.. Now has the same problem. Looking for a new fridge. Hope better luck this time.

2013 We purchased from Lowes Maytag washer and dryer front load stackable. We live in a house 1890. We have a closet that these units go into so we are restricted to what brand we can buy. WE read the reviews. People must lie or are paid to write good ones. Within a few weeks the washer was giving us trouble. The door latch was not closing properly and it would take up to 20-30 min. to get it to start. Called and they said the latch was stuck. Again started having problems on and off. Months went by and had another service call. Same issue. Fixed it again. 2014 again same problem. We have to order a new latch and some other part. They could not get the part. Called Maytag directly and they were back ordered. What does that tell you. This is a major problem so much so that no one anywhere had the parts. 6 wks to finally get it and got it fixed. But in the meantime, the dryer was not working correctly. The clothes were damp and lint was all over. It was like a steam bath. They came out and when they looked at the back of the dryer it was burnt. Now this is what upset me. He said it could have caught fire and burnt down our house. Nice. The dryer was shot. They said to fix it would cost more than it was worth. Our warranty gave us a new dryer. 3 wks later I have my washer and dryer back working. In the meantime we have spent more time at the laundromat than at home. Brand new washer and dryer and are going to the laundromat. We had the dryer 5 days before it stopped working. Brand new dryer. Called and got a service call. The spring on the start button was not correctly put in. Who inspects these products. This was not right from the factory. So they fix it. Said if it happened again they would need to replace the entire thing. I do not know what that means. That was Dec. End of Dec. the washing machine is not running through the cycle. It had weird display on the washer. Thought maybe it was overloaded. Had to cancel and drain and then hit drain and spin. This takes not only more time but more electricity. I put in 2 sheets and it did it again. Had a few loads that ran properly and again it started. Called for service. He comes out and the motor that runs the belt to spin and some circuit board is shot. They call 2 days later and say that no parts can be found anywhere. WTH! It is 18 mos old and already the parts are extinct. So the warranty company said it was not worth fixing. They are giving us a new washer.I remember the commercials about Maytag that the repairmen had nothing to do. Well I thought it was because they did not break down. No... they cannot find parts. This is unacceptable. We have to go through the inconvenience of them not working and schlepping to the laundromat baskets of clothes. In the winter this is not fun. We are retired. Have to walk down icy steps. I have a washer/dryer upstairs and I cannot use them. Dont work. Not just the aggravation of dealing with repairs but not getting parts available, then having to wait to get money back to order a new washer and dryer and then get the dryer and 5 days later it doesnt work. Now we have to wait 2 wks for a new washer. It better work. Have to buy the warranty over again on each product cause they fulfill it when they buy you a new product. So this costs us extra money. The money we pay at the laundromat. The cost of electricity every time we have to run the washer 3-4 times to get it to spin out the water so I can dry them.To say I am upset is an understatement. I was told by a rep at Lowes, well Maytag has about 3 lemons a yr and you just got all of them. That was their consolation to our problem. I think Maytag needs to inspect their product. Our house could have burnt down. It is not a matter of parts going bad but damn the stuff is not even 2 yrs old. And the dryer was 5 days old when it stopped working. WE had a Maytag dishwasher and it was installed brand new and did not work. It had a defect in it. I never got to wash one dish in it and it had to be repaired. So I am not happy with Maytag. You go on Facebook and tell your story and all the Maytag horror stories come out. You need to do something to save yourself. Your company name is going down the tubes. Thought you should know this.

Bought a Maytag Washer, in 2010 the Bravo. Good looking washer and dryer. I bought a 4 yr warranty for both. My washer has needed service every yr of the warranty, leaks and has stopped running. Now it is out of warranty and it is leaking again. Was just fixed a little over a year ago. I am now seeing a lot of rust around the top of the washer. It has just about covered the one port where you put the bleach in. The seam around the top in the crease is full of rust. My dryer is fine, bought them both at the same time. I have never seen this on a washer before. My mom has had her Maytag for yrs no problem. I bought these thinking they would last, boy was I wrong.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

I would not recommend a Maytag front load washer to anyone. I bought a Maytag Maxima 4 years ago and it looks like its not even available any longer so Im writing my review on a similar machine because after much research Im finding that all the Maytags have a similar issue. I have an MHW7000XG1 model large capacity washer. After 4 years the MCU went out and the cost to repair is $500. I looked up the error online and sadly there are so many others with the same problem. I had always thought that Maytag was built to last, however, after lots of research I am finding that 3-5 years is all you get before either the MCU or CCU (or both) have to be replaced. After replacement most people get another few years and then it has to be replaced again. By that time I could have purchased a brand new washing machine. The appliance repair company told me to get a Speed Queen. Thats the washer/dryer he has. They are built to last up to 20-25 years. Im a single mom and cant afford to repair my washer or buy a new one so it looks like Ill be doing laundry at relatives house for a while. Terrible product and definitely not worth the $1500 I spent on it 4 years ago.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

I will never buy another Maytag product. Our dishwasher is not even 2 years old and the control board went bad. No extended warranty was purchased because we assumed that it would last longer than 2 years when our Sears Kenmore lasted 25 years. No help from customer service. We now have to spend over $300 to get this piece of junk repaired.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

My dryer is 3 years old and I have had a technician work on it 3 times in 2 weeks, replacing parts as well as screws that were not installed. The dryer is not drying clothes and resets. Yes, I clean the filter.

After one year, this famous Neptune washing machine began to sound so noisy during the spin cycle that neighbors must have thought a 747 was taking off from our house. After researching the web, I found that the main bearing always fails in this machine and there is a new one-man repair industry started up across the US to just replace these bearings. In fact, someone invented a bearing puller just for this problem. I am deeply disappointed that a once fine company would knowingly put out such trash. I am replacing ours with another brand, even though we have used Maytag for 30 years. Customers always determine who wins and who loses in the long run. Bye, Maytag!

JADE model RJRS4270. Had this model for 10 years with more than 10 service calls. Always breaking down and Whirlpool will not honor the warranty. Paid for an extended warranty service to Maytag/Whirlpool offered by the manufacturer. When unit broke Whirlpools warranty service provider Assurance said Whirlpool no longer provides the parts needed, sorry can’t honor the extended warranty you had paid for, no parts, and no refund. The evaporator drip tray had been replaced three times. Asked to have the unit replaced. Whirlpool was absolutely disrespectful and only offered me to the option to buy another discounted $8K unit for a with ~ $2K discount.So far approx. $6K unit + approx. $1K extended warranty (not honored) + approx. $1K parts and service out of my pocket (Whirlpool continued to tell me it was not warranted). Although the operator’s manual said it was covered. While under warranty Whirlpool doesnt have replacement parts to service it. Multiple service tech are telling me there are many known issues with this unit. Found out there’s class action law for the same issues Im experiencing. Whirlpool only offered a new unit at approx. $6K. So total for me to date if I choose to take the discounted unit would be $12K. Dont buy this unless you have a good lawyer. Hardly seems reasonable. Extraordinary time/money loss and aggravation.Bought 8/1/05 S/N ** Model RJRS4270C $5,400. Service call 5/10/06 Repair - Freezer dripping water and pooling on floor. Service call 6/28/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/5/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/12/06 Repair - Unit not defrosting. Service call 8/26/06 Repair - Freezer not cooling, ice backup, fan burn out, drip tray. Service call 9/2/06 Repair - Evaporator fan not working. Replaced unit 9/_/06 S/N ** Model RJRS4270D. Maytag Dependability Plus Cert No. ** $99.00 8/02/08 thru 8/02/11. Maytag Extended Service Plan Plan No. ** $297.19 9/02/09 thru 9/01/12. Maytag Extended Service Plan Plan No. ** $405.31 9/01/12 thru 9/01/2015. Service call 10/13/10 Repair - Ice build up in fan, freezer not working. Service call 10/20/10 Repair - Installed new drip pan, bi metal, fan motor. Service call ~ 8/_/15 Repair - Service tech states, Whirlpool no longer has parts. Even though we paid hundreds to have a still active Maytag contract extended warranty. Whirlpool outsourced service to third party. Service call ~8/_/15 Service tech refuses to repair because cant get parts from Whirlpool. Asked me to find part on eBay or some other source so he could repair since Whirlpool could not provide. Got part. He did fix. Freezer stopped working 4/2/16. Customer support 4/3/16 followed owners manual instructions for warranty and call number, Whirlpool said theres no warranty and to call any local service tech. (Owners manual said compressor was still under warranty). Service call 4/4/16. Tech refused to work this Whirlpool unit, believes to be issue with the compressor leaking or system blockage or bad valve in compressor. Customer support call back - Krisi, was warranted. Jade Specialty Department. Customer support call back - Jared, no warranty, sorry. Explained contract to him. Nope/Nada. Customer support transfer - Jan, yes was warranted. Asked to speak to manager/sup. Said if you won’t honor warranty then please provide replacement. Transfer to Mike said we must schedule service through Whirlpool to fix contradicts. We asked for reference number to track. Mike said they don’t use reference numbers (contradicts Jared from when he asked me for a reference number). Two days no call from Whirlpool. Customer support call back 4/7/16 - Kari, offered small discount for equivalent new or refurbished unit $5,739 for Model KBSN602ESS. Said although under warranty, Whirlpool may not be able to provide parts to repair unit, but they will sell me an equivalent unit.

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

I purchased this washer two years ago. It is supposed to be high efficiency so I was using cold water with the Water level sensor. The first load of dark clothes I washed came out with soap streaks all over them. This happened every time I washed dark clothes and sometimes they were barely wet. I emailed Maytag but they didn’t reply, so I called customer service and was told I should always use warm water and when washing dark clothes select a deep water wash. How is this HE?? When I wash towels or sheets everything comes out tangled and I am only putting in one set of queen size sheets. I will never buy another Maytag.

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

I purchased a Maytag dishwasher because they are supposed to be known to be a good brand. But my dishwasher is 3 years old and it started rusting around a steam vent on the outside of the door! This issue has been ongoing but as Ive been busy, I havent had the time to address the problem with Maytag since its out of warranty anyway. But I feel like this should not be a warranty issue to begin with, it should be a recall issue. I had a plumber look at this, and he said that it was caused because the vent was not properly sealed during manufacturing. Now it looks as though mold spores are growing inside the steam vent! Maytag will not stand behind their product, so why should I invest anymore money into it?! I would rather purchase another dishwasher (OTHER THAN THIS BRAND) than dump another penny into this garbage dishwasher!

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

I bought a Maytag washer November Thanksgiving of 2013. This washer started giving problems three months after; problems such as the cycle stop turn over properly, the light would say wash but its not washing. It would just stop but the light stuck on wash for long periods of time. Press the pause/start/cancel button, it would sometimes start again and stop and let out the water quickly. The clothes would be filled with water and not wash properly. This the funny part, serious funny part. I contacted Maytag on countless time. They had me on hold so long I had to hang up; a hold for hour I am talking about. One day I finally got through. They gave me a number to contact because where I am located there is no tech. I never got anyone but the machine when I called the number after countless times of trying. I decided to called back Brandsmart, because I just think its not right and fair to me to purchase a washer for so much, to had it shipped for more money. It didnt last me NO time at all and I cannot get any help. Well! Brandsmart told had to have paid export shipping, something I never was offered and since I took it out of the country, there is nothing they can do for me. I hunted for my receipt and to this day I I still have it. All was offered was warranty parts and labor for a month, thirty days. I said no because I would not think anything would go wrong in that short period of time. Nevertheless was not offered any export shipping warranty like what they are trying to ** me with. Here is my receipt number **. I grieve presently how I was just robbed of my money so openly when all I wanted was a replacement.

After 30 months of light use.... two adults in the house, the top of the machine at the ports that allow adding fabric softener and bleach have rusted in a severe way. The machine is rusting away and Maytag customer service will say nothing except, it is out of warranty. I am very sad that I purchased a $719 washer that is falling apart with scant use.... Maytag no longer stands behind the product and I will never buy another one of their appliances again!

Our Maytag dishwasher was just past the 1-year mark when the control panel stopped working. A certified Maytag repair service came out to diagnose just that and charged us $89. Maytag sent the user interface out to us, and my husband noted that there was absolutely no way that the part could be installed wrong. The wires could only go one way. The repair service (DSM Appliance Service) wanted another $120 to install it. We installed it, and it still doesnt work. Maytag will no longer assist us in any way. I will never buy a Maytag or Whirlpool appliance again. After investigating, I see that this control panel issue has happened many, many times; and I wonder why there hasnt been something done about it.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

Our Maytag oven (not sure model) in the first year started doing crazy things with the oven computer. The oven would shut off and come back on and the display would be garbled. Also when my girlfriend tried to pull the turkey out, the rack fell off the left side and dumped all the juices into the oven. She almost got burned and there was a lot of smoke. The freakin rack should never fall off! Also our dishwasher is on its second control board. I lived by Mr. Maytag and his airplanes/helicopters at Crest airpark in Covington, WA. I wish I still did. Id like to ask him what he thinks of his crappy products. You get nothing for your money anymore. Im not sure but Ill bet both of my problems with these products have something to do with saving a buck by making this crap in Mexico or some other *** hole. Im just glad Maytag doesnt make airplanes or medical equipment.

I have Maytag dishwasher model # MDB7609AWB2. I purchased it from Sears on 5.30.10. It was installed 3 weeks later. From June 2010 through November 2011, the dishwasher has stopped working 3 times, every 6 months, requiring a service call to fix the electrical /circuit board problems. The aggravation of owning a poorly built machine and inconvenience of waiting for Sears to send a repair person has sealed our decision to stop doing business with Sears and Maytag.

We bought this washer in 2009. It has only been 5 years and we had a problem with the lid, now it leaks on the floor and most of all it has been rusting on the lid, the sides and rusting around the bleach port. Rusting on the top edge of the outside metal skin. I am not happy with this product at all. The serial number CV0870202. Model number is MVWB800VQZ. It is a quiet series purchased on 2009. I am not happy with the quality of this washer and I will not buy another Maytag.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

Model # MF12269VEQ1 French doors with bottom freezer - This refrigerator was purchased March 2011 and it is forming a sheet of ice on the bottom of the freezer. We tried unplugging it overnight to see if it would correct itself and it hadnt. I googled this complaint and called the manufacturer to see if there was a recall. It seems a lot of people are having this problem. Several comments are to pour hot water in the drain plug or use a blow dryer to to the plug; however, you have to disassemble the whole bottom freezer, then unscrew the back to get to the drain plug. I feel this is a defect in this refrigerator.This unit was approx. $1600.00 and should not be having this type of problem. Who knows if I could actually get to it to try these things, that it could keep recurring. Im very upset as my husband and I are seniors on a fixed budget. We bought the name Maytag because we thought they built good products.

I built my home and bought all Maytag appliances. The freezer and fridge knock on wood have been repair free. Replaced control panel on stove for 400.00$. Washer after 2nd repair had to replace 600.00$. Dryer repaired once 95.00$. Replaced dishwasher with a new Maytag. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. This is the 4th repair. I have paid for 2 repairs out of warranty. 380.00$ the last repair. I did request some help from Maytag. They said no... My dealer did only charge me for the parts.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

Purchased this Calypso machine as a second machine for my ranch to handle really dirty clothes. Purchased from Sears Outlet as a refurb machine would be fine for the purpose. Machine was alleged to work by Sears. Paid several hundred for the machine, brought it home, and voila it does not work. New hoses, ran all the checks, and will not fill. Called Sears and, despite the statements of the manager, was told that I have to have a 3 day old machine repaired and not replaced. This POS did not even work out of the box. Years ago I had a Calypso which is now a flower pot. Junk, Junk, Junk. NEVER buy anything from Maytag or Whirlpool.

I bought a French door refrigerator on May 23, 2012. It is now July 9, 2014 and the repairman has told me the compressor is bad. Maytag will do nothing about it because it is out of the 1 year warranty. I am very disappointed because I thought I was buying a quality appliance. I will never purchase another Maytag appliance!

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

I bought this washer on 6-29-14, should have returned it within my 30 days but kept thinking it will get better, NO. I actually like to use water to wash my clothes!! It doesnt even get all the clothes wet when using on the bulky/or any other setting. Very disappointed in Maytag!!! Washer for sale, very cheap even though I paid $500 with warranty.

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

I purchased a Maytag Centennial washer and dryer on February 4th. It was delivered on the 11th. I am dissatisfied with the performance of the washer. I use the same amount of detergent and fabric softener as I did for my 15-year old Maytag washer, but the wash is not as soft as with the old machine. Also, the wash when finished appears to be a lot wetter. What is wrong? What else can I do?

I bought a Maytag Bravos washer and dryer two years ago. A week after the one year warranty was up, my dryer broke. That was in October. It took me until February to get it fixed, but within two months it broke again. It has taken me until now to get it fixed again and they found the same problem; the thermal fuse blew. Both times it has cost me over $100 to get fixed, but I still cant use every part of the top panel; I can only use timed dry cycle. I’m expecting the dryer to go again. The repair man had to re-glue the seal that went around the drum. The vents were all clean and were blowing fine, so we’re not sure why this keeps happening. Our family have always owned Maytags and they have always lasted for 20+ years. I am so disappointed with Maytag at this point and will never buy another again. Go back to the old days, Maytag! By the way, has anyone noticed they dont run the Maytag commercials anymore, because I have!

I purchased a Maytag gas dryer in November 2011. This is January 2012. I have got to use mine maybe 2 weeks altogether since I had it. It is to be repaired for the 4th time tomorrow. In the meantime, I have to go to the laundry mat to dry clothes, Maytag refuses to do anything about this. They say they are helping me by getting it repaired each time it breaks down. I want a new dryer. The retailer I bought it from will not stand behind this product either. You see these commercials on TV where the Maytag guy is sitting back and waiting on a call. Thats a bunch of ***! I have never purchased a product from anyone that they would not stand behind it especially for the 4th time in two months. I will never buy another Maytag product as long as I live and I will tell everyone that I know not to buy one either.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

The top loader washer Commercial Technology washes very small loads well. I bought it for the deepwater wash. It DOES NOT work. It also has a auto sensing. Hate this washer. I have to pour buckets of water in the wash to fill it. Maytag/Whirlpool go back to the way it should be. If I want a full washer I should have it! At the end of the day IT IS MY WATER BILL!

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

After speaking to a Kim today... Im more than angry. The control panel on my dishwasher is broken. Had repair come out and they told me a few months past warranty. Kim tells me the only thing still under warranty are the racks?! Im extremely angry at the poor service we are receiving but pleased as we have cancelled the washer and dryer (Maytag). If youre thinking of going Maytag or Whirlpool, cancel! Not worth the headaches or cost.

The first washer my husband and I ever purchased was a somewhat cheap top loader but it worked very well for over 10 years. We decided to fall for a bargain sale at Home Depot and went with the HE Bravos model. We were told that it would save us money and work great! From day one weve had issues. It never really seemed to clean right. It gets thrown off balance if you have more than one bath towel in a load at a time. After an angry call to the company and a somewhat helpful customer service rep, I began washing every load at the deep clean heavily soiled cycle and then did an extra rinse to boot. So much for energy efficient. So, fast forward 4 years, I HATE this washer but cant justify a new one at this time. Now, it stops mid cycle and I have to unplug it then plug it back in and restart it. When this happens, there is an awful smell. Needless to say, well be buying a new washer within a week or 2 and you can bet your life, it will NOT be a Maytag.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

Part on fridge is defective. They have sent the part but tell me they dont have anyone in the area to work on it. Nor will they pay for someone to come out. We must replace it ourselves. This product should be on recall. Maytag fridge. Freezer door on bottom filling up with water. We have 2 of them doing this. One about 15 years old. Other one is 3 yrs old. Maytag knows of the problem but wont fix it. Wont recall their default product.

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

This washer is a piece of expensive junk. It was used sparingly (2 people using it) for 16 months when a repair service had to be called. The estimate to fix the machine ($980) exceeded the initial cost. It did not clean the clothes adequately when it was working. There was a powdery substance on the clothes when they were removed. The clothes were always bunched up and intertwined. Only the proper type and amount of soap was used. I cant recommend this washer to anyone. We were very disappointed since we have always purchased Maytag washers/dryers. Never again.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

Its frustrating the way the bottom of the dishwasher has curves making wasted space. Second, the tracks for the trays are such that often the tray comes off the track and makes it difficult to get back on without unloading dirty dishes to do so. Finally, I really dont get the lighting system for dishwashing on the outside of the machine.

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

White clothes come out with some sort of grease stains on them and darks come out with a detergent white scum on them. I have to put them through twice to get the scum off and I have to scrub my whites by hand. So much for your new type washers. If I could find a washer with an agitator and water saver on it, I would buy it in a flash and get rid of this so called newest thing on the market. I have to put a cleaner through it every 2-3 weeks that costs me $10.00 for 3 pucks and having to rewash my clothes does not save water or time. There is a lot to be said for the washers that had water saver on them. First of all, I could open the lid during the wash cycle and add another item. (2) I could use the last of the 2 rinse cycles from my white clothes to start a load of dark clothes, that was truly a water saver and both loads were sparkling clean. Every women that I have discussed these new machines with (both front loaders and top loaders) say that you and other companies that think you have improved wash day for women have definitely not improved it but rather made it a nightmare. Absolutely hate this product. I hasnt given me a moments satisfaction since we spent the $1,000.00.

This is the noisiest washing machine ever manufactured - cannot do laundry at night or no one sleeps, during the evening it overpowers the television. Dark washes are a nightmare as there is a white smear (soap scum?) on everything (guess you don’t see it on whites) - extra rinse does not help. What happened to this “reliable company”???

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

I purchased a Maytag double door refrigerator in 2012. So far the deli drawer has broken 3 times in the same way. There is a plastic peg attached to a side panel on the refrigerator. This pin breaks off after a few months of use. To repair it, you have to replace the entire side panel. The parts and labor costs are about $200 each time. It is obviously a design flaw that Maytag should fix. If you repair it every time it breaks, in about 8 years your repair costs are more than your original purchase price for the refrigerator. Dont buy Maytag products. They are inferior.

So the reviews for the Bravos MCT online were pretty decent. We purchased our set from Lowes. However, the clothes dont turn over. I watched as long as I could (getting frustrated the longer I watched) to see how the clothes were going to get turned over and washed. All they did was get rubbed on the bottom of the pile where those agitator fins are. But they never got a good flipping so that the top of the pile was washed. I only had 4 normal size towels in there. So it isnt like I had too many clothes.So I called Maytag to tell them what I was observing and the gentlemen explained that it was counter-intuitive technology and that it seems like they wont come clean but he promised me by the time the load was done they would be clean. Yet - they did not come clean! The dirt on the towel was still there on the top of the load with dog hair. NOT TO MENTION SUDS!! Im so disappointed because the burden is on me to either take this set back or deal with it. Buyer beware - if you look at this machine and ask yourself how in the world will the clothes get clean - you are asking a great question! They dont!!

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

Our Maytag dishwasher is a work horse. Never a problem just runs and runs. Could be a little quiet quieter. But does a t great job cleaning. I would definitely buy another one and would recommend it to any one.

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

I had a Maytag dishwasher (made by Whirlpool) that after 4 months of ordering wrong parts, parts arriving damaged, and parts that were re-engineered and did not match up, the dishwasher could not be fixed. The extended warranty people (AIG) promised me twice on a recorded telephone call that they would exchange my dishwasher, and after many many heated telephone conversations was given a 20 minute lecture on how the word exchange does not mean they will replace it. The frustration ultimately overtook my misspent loyalty in anything made by Whirlpool and I decided to accept the buyout of my extended warranty contract, at a loss of hundreds of dollars to me - well worth getting rid of that dishwasher and any further affiliation with Whirlpool corporation. Absolutely horrible customer service. Unbelievably god awful treatment. I dont know what happened to customer service at Whirlpool, but my dealing with them has convinced me that the term is an oxymoron at Whirlpool. Horrible horrible customer service. I have never been treated so poorly in my life. I truly dont know how they can still be in business if they treat their customers like they did me.

Yesterday I was using my washer (small load of clothes), I was with my baby in the laundry room when suddenly there was a horrible noise and the door of the washer opened, he hit my back, something fatal could have happened. I do not know how it happened but a piece of concrete was inside the drum. I do not want to imagine what would have happened if that piece came out and hurt my baby. I spoke to the company and explained what had happened to me, but they do not want to be responsible for what happened because the washer is in Tijuana (border with San Diego), I bought the washer in Pirch San Diego California in 2015. Maytag United States is responsible for this defect. Dont buy this model:mhw8100dc extra large capacity washer with steam and powerwash® system-4.5 cu. Ft.

I purchased this Range about a month ago and would return it to the store if it wasnt such a hassle. The set of grates that came with had 1/4 drop from the center to front of stove. Whirlpool sent a new set; they were no better. Then customer service wanted to send a Tech out to see if the grates were out of spec. If they are out of spec they will replace. If not I will be charged $89 for a service call. Whirlpool customer service assured me their service rep would have new grates on his truck. So I drove to their service provider, he laughed and said imagine they want me to send a service Tech out to look at cooking grates and NO they don’t stock them. If you want a cooking surface that is level and does not SCRATCH BOTTOMS all your cookware. The convection oven is also a joke. In order to bake something in the specified recipe time, I have to set bake temp 25 degrees higher to compensate for convection ovens automatic temp set back feature. When I turn on LF burner flames engulf 10” pan, a truly fire hazard. I have a Maytag dishwasher and dryer, love them both. Maytag should stick with dishwashers and laundry. I never have been more dissatisfied with a major appliance. I would NOT PURCHASE THIS PRODUCT.

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

Maytag 7000 series front loaders bought in 2013 on basis of high ratings from Consumer Reports. Also durable and look good in the process. Had for 3 years. Machines highly rated by Consumer Reports and bought on sale. They were a very good value. Both W & D have steam feature but find Ive rarely used it. Durability is key, as is the ability to balance wide variety of loads, which our machines do well. Capacity of 5 cu ft or better sufficient for a household of 2. Maytag reputation for durability and reliability and made in US, though a clone of Whirlpool. These are big, heavy machines, best for side by side but they can be stacked. The units are quiet, have more features than weve ever used and so far have been reliable, gentle on clothes incl delicates and drum bearings really help with keeping loads balanced. Door hinges built like a tank but the chassis theyre attached to arent up to par. W & D have stainless drums. Washer is resistant to mold & odors but dryer lint system convoluted in design and hard to clean out.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

I bought a new Maytag dryer model # MEDC555DW2 18 months ago. Prior I had owned a Whirlpool for 22 years and the only expense on maintenance was that I replaced 3 belts. This new Maytag started making a terrible noise so I called the store where I bought and they sent out a tech. $76.77 they charged me to...remove a penny from where it got lodged in the edge of the drum somehow. Maytag refuses to do anything about it and I feel like Ive gotten the shaft because I bought an inferior product. In 22 years Id guess I dried on accident over 100 dollars in change since I have kids. Should have bought a Whirlpool again and so should you. Ill never buy another Maytag product. Ever.

My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

This machine(Bravos XL Washing Machine) was highly recommended to me at the Home Depot by a sales associate. I broke down and took the recommendation. Oh how I regret that! This is a terrible washing machine. It does not put enough water into the machine to even cover the clothes halfway. It ties the clothes in knots! I made a terrible mistake when I purchased this!

I bought this washer 2 years ago, it has always been noisy and not cleaned or rinsed my clothes very well. With dark clothes, I have to rinse them twice if not three times. Now it has quit throwing out the water all together and is not rinsing the clothes at all. Paid $72 for a repair man to hook it up to his computer and tell me there was nothing wrong with it. Told me it was how I was loading it. I dont think so. Now I have to replace a two-year old machine. I will buy a basic machine that only washes my clothes this time. Nothing is made to last these days.

Horrific, useless, inconsiderate, rude, discourteous, arrogant and banal! I bought a brand new washer and dryer. The dryer is steam type and defective and they will not exchange, despite never being used. Nowhere am I committed to an agreement saying that the machine will not be replaced if it is defective. I am getting the run-around from the store, the manufacturer and the service technicians that didnt even arrive with tools when they came to evaluate the problem. If I had my way, I would return the washer and dryer and change manufacturers. But it is a stacking unit and I used the washer which commits me to it! Maytag, Whirlpool, JennAir and KitchenAid are all the same company. I am running out of options except going to the European manufacturers! Miele will at least install the appliances. They will be my next machines and I will not have to pay a plumber twice to install them the next time!

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

Purchased this machine to replace the recalled Samsung washer that was exploding. I should have kept my Samsung. I loved it and had no complaints, but since there were reports of it exploding I took the rebate and purchased the Maytag Bravo Nightmare. Everything you have read or will read here is true. I would spend hours, I mean hours trying to do a load of laundry. If the cycle would complete itself, the clothes would be soaking wet, and they never smelled clean. I would try rinsing again and the cycle would start out with 18 minutes and I would return to the machine 1 hour later and it would be still running water and still have 18 minutes or more left. I watched it complete the spin cycle and start the rinse cycle again. We had the service guy out several times - he would call the techs and they would test the machine and say nothing was wrong other than it was off balance. They said I was using the wrong detergent - when proving that I was using an HE detergent, they counseled me on how to lay the laundry into the machine, and said I was using too much laundry detergent. After babysitting this machine for more than a year, and being told by Lowes Customer Service that the techs say there is nothing wrong with the it, I was fed up. I called Lowes and told them to send their techs to my house to do the laundry. I threatened to call for service every week until my extended warranty was exhausted. They finally gave me a merchandise card valued worth the purchase of the machine. Now, I have the painful decision of deciding what to buy next - It wont be a Maytag!

We purchased a Maytag Bravo Washer and Dryer in late 2007. We had a one-year warranty on the set. At just over 2 years, we started having problems with the washer. It started making a loud noise when spinning and started beeping all the time during the cycles. We contacted Maytag and they said the only thing they could do for us was to sell us an extended/repair warranty for $320.00. If the cost of fixing the machine was too much, they had the option to replace it with another machine equal to the value of the machine in todays market, or cash, or a gift card equal to that.We were angry about the cost of the warranty and we were unemployed at the time and couldnt afford that so we just had to let it go. The machine progressively got worse where only two of the cycles would work, but not without beeping several times where you had to fix the load, and the sound got so loud it sounded like you had a jet plane just overhead. Just the other day it completely quit working. We have been in contact with Maytag several times but their only answer is their repair warranty. Weve talked to numerous appliance repairman, who all knew exactly what was wrong because they have seen it so many times, and they told us that we have several things going wrong with the machine we would probably need a new drum, a new drain pump and a new control board.We were told that it would cost more to just buy the parts than it would be to buy a new machine. In the course of our phone calls to Maytag, they have continually told us that they are sorry but there is nothing they can do, in fact they only have record of two of our calls (how convenient!). Since experiencing the issues with the machine, we have researched it online and found that scores of consumers are dealing with the exact same problems we are having which shows that there are defects in the manufacturing of these machines. Maytag should be forced to fix these problems. They are well aware of them and they should have to back up their products.There should be a class action lawsuit out against them. We were told by an appliance repairman that Whirlpool (who bought out Maytag) has a washer called Cabrio that is the exact same model as the Bravo and that they do have a class action lawsuit out against this model. Consumers that purchased the Bravo should be included in that lawsuit. I am stuck with a broken down washer, mildewing clothes and dont know where to turn outside of paying out the money for the extended warranty with no guarantee of what we would get out of it, purchasing a used set with no guarantee, or putting out the expense for a new set.This set was an expense set and we went with Maytag because they used to have a good reputation, but we feel like we have been totally cheated. If the appliance companies were forced to offer a longer warranty on their products, they would have to manufacture them at a higher standard. For the cost of these new machines this is exactly what we as consumers should expect. Please help us to know which direction to go. Even with purchasing a new machine we are apprehensive!

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

I purchased a Maytag dishwasher model MDB7749AWB2 in Dec. 2011 from Home Depot after a major flood destroyed my entire first floor of my house. I had replaced a previous dishwasher only a short time before the flood. This dishwasher is JUNK. I was lucky I bought a five year extended warranty on it which actually gave me 6 years. I needed it. Within a year the control panel went. Then water started spraying out the side of door. Then it sounded like it was crushing ice every time I ran it. Then the control panel went out again. Ice noise came back again. Control panel a 3rd time. It runs for hours as it is.Now the warranty is expired and last time I ran it the start light was blinking a few hours later. We were having high winds on and off so I thought maybe the power went on and off and that’s why it was blinking. Today I turned it on and after about 45 minutes I realized I didn’t hear it running anymore so I got up and looked and sure enough it wasn’t on. Normally the clean light is lit when done. I opened the dishwasher to see it filled with water still. I tried to hit cancel/drain but nothing works yet again. Wonderful news for a single mom that can’t afford to fix this over and over! Maytag is the worse company. Their dishwashers are horrible and they should be doing something about this as I’m not the only one that has had this issue. Home Depot was just as useless. Will NEVER buy again.

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.