We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

I have a Maytag Bravos washer that has gotten to where every time you try to run the final spin, you get an unbalanced load code and it shuts off - it does this even when you try running it empty. This washer is 3 years old, and has been doing this progressively worse for the last 4 months until now. We cannot even get it run the final spin cycle now.

Maytag Model #MGR7662 range - We inherited this oven when we bought my mother-in-laws house 2 years ago. We had to get a thermometer to keep in the oven since the temperature is never consistent and is usually 50-100 degrees lower than the digital readout. We will be replacing this oven as soon as we can and it will NOT be a Maytag.

Maytag model mfd2561hes French door stainless steel purchased in June 2005 has been the worst appliance purchase ever. After 1 year warranty expired, icemaker and water dispenser stopped working. Was told by repairman to thaw the tube for water dispensing with a hair dryer. Are you kidding me? Why should I have to pull a huge refrigerator out from wall and put the hair dryer to it to thaw out the water line when I need water? What is the convenience to that? Cant buy fresh vegetables as it will freeze before I can use it. This is the worst appliance ever. Dont buy Maytag products. Maytag doesnt back products like the old days when they would last 20 + years. Cant last even a year anymore. Sad!

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

Omg I am so shocked at all the complaints about these refrigerators.. I too bought refrigerator, stove, microwave, dishwasher from Lowes after a storm just about destroyed our home. I was so excited to have such a beautiful refrigerator and new kitchen...but shortly after it started freezing on the bottom of freezer and leaking all over. My new floors and kitchen cabinet are ruined. Every other day we have to break up ice and clean it out from freezer.. it still then leaks.. several family members have slipped and hurt themselves. Please if anyone knows how to get it fixed without it costing us a fortune let us know. Maytag (Whirlpool) knows it is a defect... Why will they not fix it? I cant afford a new refrigerator and shouldnt have to after only two years.. If a class action comes up.. please contact me. Shame on them...

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

We purchased a Maytag dishwasher from Home Depot in January 2009. We did not begin using it until perhaps March of 2009, so just over 2 years ago. It gets ran maybe 1 to 2 times per week. I went to turn it on a day ago and the right side of the control panel, where you press the start button, does not work. When I checked Maytags website, I discovered there was a recall due to the heating element. So, I had the repair technician out and he told me that the control panel was bad and it would cost $300 for parts and labor to repair. We paid $600 for this dishwasher. Of course, we have the option of purchasing a new dishwasher and receive a rebate but that ends up being more than just ordering parts and replacing them ourselves, but something only 2 years old should not break. From reading all the other complaints on this forum, I am surprised that Maytag has not done something about the control panel and the humidity issue which seems to cause the control panel to go out. This is an expensive fix which Maytag needs to address. Come on Maytag!

I am a Baby Boomer... just like so many of us, I watched those lonely Maytag Repairman television commercials. Yes, silly me I purchased our top loading Maytag Bravos XL because of the brand name and because the machine was large enough to wash our bedding. Well, like so many fellow purchasers have found, this machine does not get the clothes clean and leaves soap spots all over the clothes. Its embarrassing. Additionally, there is that funny smell after the clothes come out of the wash. Well, Maytag has really done a number on us all. Kudos to their research & development department for creating a washing machine where the clothes come out dirtier. Has Maytag thought about a RECALL? I will tell everyone I know to NEVER buy a Maytag.

Disturbing that this product made it into production. I have the matching dryer too, and its just as bad. First the washer rolls up clothes into a tight ball better than I could do if I did it by hand. Then it spins, setting the wrinkles in thoroughly. Then, even though I shake out the clothes before putting in dryer, after the clothes come out of the dryer (without letting them sit in there) - the clothes look like someone drove over them with a car while they were rolled up in a ball. Bonus: the clothes dont even get dried. Ive watched the clothes in the dryer, the drum is designed so the clothes stick to the outside of it and go around, they never actually tumble or get any air circulation. What a disastrous product.

The last Maytag washer was great, the dryer not so much, but I was able to repair it. This Bravos is sorry. 4 years old and the tube goes bad is not what you would expect from Maytag. Consequences, no more Maytag or GE for that matter, that dont leave many brands to choose from.

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

I bought this washer (Maytag HE) almost a year ago, and if I could redo my choice, I would not choose this machine. There is no separate spin cycle. Often items are left with quite a bit of water in at the end of the wash cycle (often literally dripping as you transfer to the dryer), and you cant just rearrange them in the washer and then spin again. The only option on the washer is to both rinse and spin, which almost never helps get out more water. So you then have a heavy load in the dryer, much longer dryer time, and higher utility bills to get some loads dry, especially bath towels, sheets, jeans, etc. The washer is large capacity, but if you fill it more than 1/2 to 2/3 full (depending on the heaviness of your items) the spin cycle definitely will not get nearly enough water out of the clothes. The lid on the washer is SLOPED!The most ridiculous design I have ever seen for a washer, everything you set on top, even for a moment - laundry detergent, folded clothes, wet clothes - ends up on the floor. And the lack of agitator means at the end of the cycle, some loads that contain a sheet or any large flat item (tablecloth, etc.) the rest of the items are captured below the larger flat item that is over them like a mushroom cap. You cant tell how long the items have been like that in the washer, but its hard to imagine they are getting properly cleaned and rinsed. You absolutely cannot use powder stain removers, especially OxiClean, unless you are using the oxi cycle (much longer than regular cycle) because with any other cycle you will have white cloudy patches on all your clothes and items where the powder dissolved in the water but did not rinse out. You have to manually scrub them out, as putting these items through another wash cycle does not remove all the spots.

I own a Maytag dishwasher model number MDB7749cBM 2. The panel on the dishwasher stopped working. It is only a year old. Its too new to break down. Will contact Maytag today. There are so many complaints. Why not a recall?

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

In 2003, I purchased a brand new Maytag washer and dryer set, I chose Maytag because of their reputation. Within the first 6 months, I had a bearing go bad on it and that had to be fixed. It has become noisier and noisier throughout the years and now it is leaking all over the floor when I do a load. I am single, I live alone, I do laundry very seldom and do not do large loads. I am so disappointed with Maytag. When the repairman came out initially to fix it, he said that the brand he fixes most often is Maytag. Expensive lesson learned, Ill never buy any type of Maytag product again.

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

Purchased a Maytag top loader. Hand wash clothes leaves a soap residue on clothes. Called Maytag they sent service out. Service tech said (off the record) the design of the machine does not produce enough water, but reported that machine works. Called Maytag again and they said they would need to send out a Master technician. So I set up another appointment (had to take more time off from work) with the Master technician. It was the same guy that came the week before! He didnt bother coming in to look at it! Called Maytag again and they said they would only be able to schedule a service call and if they come out and there is nothing wrong with machine, I would have to pay for the service call!!! I asked for a supervisor and explained why would I do that and he said they would send out another service technician from another service company and I wouldnt have to pay for it. He also offered me an extended warranty for a year for free. Thats great, but my machine is not fixed. This service technician said (off the record too) top loader machines are no good, do not buy, not enough water. He was there less than 5 minutes. Just got off phone with Maytag again and they can no longer do anything else, that the machine is working. I explained to the gentleman that yes the machine fills with a little bit of water and drains the water but it does NOT clean the items! Not going to let this happen to someone else. Plan on spreading the word to everyone to NOT BUY A MAYTAG TOP LOAD WASHING MACHINE. DOES NOT CLEAN YOUR CLOTHES. CONSTANT RESIDUE LEFT ON CLOTHES!

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

Maytag Bravo model MVWB750WQO. Bought this washer in 2009 for 1300 thinking it would last at least 10 years! Wrong! I loved it until a few months ago when it started making VERY LOUD noises during final spins. Sounded like the house was going to take off. Then today it started leaking water. Repairman said it needed a drum, seal and gasket. Would have cost 700-800 to fix. Needless to say we bought a new washer today, and it wasnt a Maytag!! For that much money I was expecting the washer to last a long time!

Maytag Dishwasher model #MDB7759SAW3 continues the Whirlpool company legacy of subpar control panels in all of their dishwashers. It is telling that they have been allowed to market the exact same failing parts for well over a decade without any accountability. They had one recall circa 2007-2010 and pushed customers into purchasing the model I have which suffers from the exact same control panel design.To further frustrate the consumer experience, Maytag customer service reps and supervisors allege that they have never heard of a customer having issues with their dishwasher control panel before. The panel beeps endlessly and refuses user input regardless of whether the door is opened or closed. After a power disconnect it will reset and sometimes allow one load to be washed before resuming the non stop beeping. If opened and closed during the beeping it will cycle through a completely new wash cycle on its own and resume beeping. Maytag customer service response this morning was, “thank you for being a Maytag customer”.We will my be purchasing their replacement control panels as they are of poor quality and it is well documented that the new ones fail annually as well. These are “high end” appliances and are not inexpensive. We will simply cease to use whirlpool, Maytag, Kenmore, Kitchenaid, etc. brands in our home and will advise everyone we know to protect themselves the same way.

I have a 26 cu. ft. side by side Model MZD2665HES, like most folks in my neighborhood (spec homes). The icemaker died and service was called. They looked at solenoid, and replaced the ice maker assembly as a wag that it was the problem.. still no ice, but the water was still able to be called. I replaced filter- still water only, no ice. Little did we know it was the filler tube blocked with ice, and the service man didnt once suggest turning off the water service. SO, every time water was called to either make ice or to fill a cup with, it put intense pressure on the point of assembly where the water line comes into the fridge (water inlet tube). A pin hole developed in the little plastic bit (water inlet tube plate) and every time the water was called to ice, guess what happened - it shot right out the back on drywall.Almost $20,000 dollars worth of damage to wood floor (warped), drywall (jello), and flooring (carpet) ensued. Mold was all over and had to be contained and treated for days to be fixed. Im still duking it out with service repairman and insurance companies. My advise: If you have this fridge or anything like it and the ice maker stops working, IMMEDIATELY shut down the water supply, turn the fridge off and check the filler tube in the back for ice blockage. Probably a good idea to pull the fridge forward once in a while and check the back for water also.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

I have only had this machine for 2 weeks after having a Maytag since 1994. Even broken, my old machine was far superior to this one, a Maytag Bravos. Fortunately, the salesman noted that I wouldnt be happy with this machine but, thanks to a government mandate, all new machines behave in a similar manner to save water and energy. This agitator-less machine neither washes nor rinses the clothes/bedding/towels properly. It takes four times as long to wash the items but doesnt get them nearly as clean. Today, I put 2 pairs of shorts, 2 T-shirts and a standard bed-sized mattress cover in to wash. The mattress cover never even got thoroughly wet even though I used the deep wash and extra rinse settings. Last week I put sheets in the sheet setting only to have them come out totally wrinkled and stiff as a board with soap even though I used the recommended amount of detergent. This is a disaster. Shame on Whirlpool/Maytag and the U.S. Govt. A river and a flat rock would work better!

We purchased this product from Lowe’s in 2009. We liked it for the first 6 months. Then it started putting holes in our clothes, the washer smells bad, coins get stuck, and make noise. Something needs to be done because there are thousands of upset consumers out there, all with the same complaints and Maytag does nothing. It’s not Lowe’s fault. They didnt make the washer. Read all of the complaints here.

My husband and I bought this refrigerator on 11/24/17 at Lowes for $2969.00 (excluding tax and white glove delivery). Never thought that not even after less than 2 years we would be having so many issues with this unit. The fridge part stopped cooling a couple of months ago and we were told by a technician that it was due to some coolant issue which of course our home warranty (Choice Home Warranty) wouldnt cover the repair. Well my husband fought them and we were able to have a second technician come and told us it was a sensor issue which he replaced. In the meantime I called Maytag to complain and they wouldnt even send someone to take a look. Anyway, the fridge worked after they replaced the sensor but unfortunately last week we started having the same issue. You would think for such a price you would get a decent unit, but big mistake there...now we have to find a way to replace it and we have little kids in the house. I also find out that Lowes doesnt even carry that brand anymore, perhaps because its defective. Maytag doesnt want to help us and Lowes cant do anything about it. So please STAY AWAY!!!! Should we be compensated, yes I believe so and so does anyone going through the same issue. Money doesnt grow on trees, stop deceiving your consumers Maytag!

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

I wish I would have read reviews before I purchased this washer, but I was in a hurry to get a new machine. Maytag has a great reputation and we went on that!! My Bravos is 2 months old and we have been away for a month! What a disappointment so far. What Ive noticed is all my dark items have residue on them, and today some of my light clothes came out looking like there is grease on them. Im afraid its going to wreck more clothes! Does anyone know if theres been recalls on the Bravos XL washing machines?

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

We purchased a Maytag Gemini with serial number D40941338 and model number MGR6875AD826. It has been a complete disaster. The control panel keeps breaking down, and its now going to be replaced for the 6th time. I have asked for a new stove when I called the Maytag Extended Warranty Department, and they will not replace this defective product. Please help me.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

I have a Maytag dishwasher and the bottom rack has rusted out so that it cant hold dishes. The dividers break at the bottom. I was told by Maytag parts that this is a common problem and theyre hearing from a lot of consumers about this, but it will cost $196 to replace.I spoke with customer service who told me that dishwashers only last 8 to 10 years” and since mine is 8 years old, I should expect that it would rust. Thats unbelievable. They wont replace the rack, nor offer it at a discount.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

My microwave is just 3 yrs old. SE error. Yeah, what a crock...Such junk. However, if we would just manufacture everything in the USA not only would we get better quality, but we would have more jobs. USA stop selling out to cheaper countries and pumping out more volume for less overhead.

We bought a Bravos washer 13 months ago and its been problem after problem. We had 6 service calls and the problems continue. From bearings being replaced to sensors to error codes, and now the washer drips water. This is the worst washer I ever owned.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

This review is for a Maytag dishwasher. I do not know the Make/Model. It did a very poor job of washing the dishes. It may have been the city water, but no matter what I put into the machine to keep the dishes from being cloudy it never worked. It became disabled about a year after we moved in, and it was only about 6 years old. However, there were two families before me that used it and I have no idea how they used it. It was the first and last Maytag dishwasher I will ever use.

The washer has been inconsistent and had required five warranty visits. The computer that runs it has often malfunctioned requiring frequent restarts by unplugging the machine. Stay away.

On August 25, 2011, we purchased a Maytag washing machine (Model Number MVVYC400XW2) at the Lowes Saugus, MA, store. Initially, we had no performance problems with it; however, on January 12, 2012, the washing machine wouldnt start. That day, I called Maytag for service on the machine, and it was fixed. Then on August 18, 2012, the same thing happened. A serviceman was called for the second time, and was repaired. Ironically, the Maytag 1- year warranty was expiring on August 24.Prior to the expiration of the Maytag warranty, I had been contacted by mail about an extended warranty plan, which I thought was being offered by Maytag, which it wasnt. The offer was being made by Federal Warranty Service Corporation. I purchased a 5-year extended warranty, expiring on August 25, 2017, the reason to have coverage for what seems to be a faulty machine. I would probably need it.Dealing with Federal Warranty has been nothing but grief. In 2012, the washing machine, had required 3 service calls, one with a Supervisor explaining my frustration with the number of service calls I have had made for the washing machine, but nothing has changed. Thus far in 2013, I have made two (2) additional calls for service on the same washing machine. Not only are there the numerous service calls made but the inconvenience of not having a washing machine, and the additional costs for outside laundering, during that time has to be taken into consideration. Additionally, my wife is 68 years old, and Im 71 (72 in August). Going up and down the stairs to the basement isnt something we should be doing, especially to find an inoperable washing machine.

I bought a Maytag washer and dryer at Lowe's when I bought my home-the price was great and I have not been disappointed in them-have had them over 3 years now. My washer has a stainless steel tup and is a top loader. The combo of the two was less than $1,000. The washing machine has deep clean, heavy load or light load, hot, warm or cool water settings, a hand wash setting and many other features that I think most consumers can appreciate.

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

This product has been a huge disappointment, from day one. It wrinkles and tears clothes beyond recognition. When I called Maytag to complain, they tried to up sell me a service contact. I explained that it works fine, as a shredder, but it is just a bad design and asked if Maytag had any recalls. He then told me if I purchase the service agreement and they cant fix it then they will refund the $$... ITS NOT BROKEN. It was crap when we got it home. Shame on me for not taking it right back to Best Buy. Someone needs to start a CLASS ACTION SUIT. I am sure they have duped many people into buying this shredding machine...

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

Purchased a new side by side American made Maytag refrigerator (Model: MSD2559XVEB ) in August 2010 from Best Buy. Just returned from a 3 week vacation and the refrigerator died shortly after we left on trip ( 14 months post purchase date ). $700 worth of food ruined.

My Maytag Refrigerator Freezer model MFI2569VEM4 started leaking water into base under bottom freezer door. It then fills up and freezes into solid sheet of ice and overflows and leaks into floor. Ruins Hardwood Floor. BEWARE!!!!! I have now seen several similar complaints online. Mine started doing this less than 2 years old!!!!!

Maytag used to make a great laundry machine. The barrel of the Bravos XL machine is very deep, and it is difficult to reach the bottom of the machine to get clothes out. My biggest complaint is that the clothes dont get clean; there is not enough water filling the machine to clean the clothes. The clothes get wet, but there is no agitator, and the water isnt deep enough to suspend the dirt and wash it away, even on the deep wash setting. There is also a lot of lint left on the clothes that cant rinse off. Why is the barrel of the machine so deep if it only fills up 1/6 of the height? I had great hopes, but I really regret buying it.

My Bravos XL is worthless!!! This lack of agitator design is totally ineffective. Dark clothes come out with white powder on them and I use the liquid detergent. Whites I soak with detergent and bleach then full wash cycle. Still stains on dish towels and socks. Never had a problem with the old agitator Maytag. And yes the wrinkle free cycle creates wrinkles. Deep water wash is only cycle that even comes close to cleaning and its far from perfect. Horrible waste of money, buyers beware!!! I thought all those negative reviews were overblown and since I couldnt find a large enough machine with an agitator, I ignored warnings and bought this garbage. Matching dryer is fine.

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

Model #MDB8959SAS1 MAYTAG Dishwasher - purchased in 2014 at Home Depot. First we had to replace the rack adjuster, and after that another part broke. Finally, the electrical control board totally melted and smelled up the house. Fortunately our breaker switch worked and it didnt cause a fire. But Ive read other reviews of this happening with Maytag dishwashers where there was a fire. It now resides at the landfill.

I am very happy with my washer. It is easy to use and does an outstanding cleaning job. I have had it for almost 7 years and have not had any problems with it. It has many different settings so it can handle virtually any cleaning job. I am particularly happy with the spin speed which is adjustable but the high speed spin really wrings the water out so the dryer which incidentally is also a Maytag drys in a fairly short time. The washer is a front loader and doesn’t use much water.

I have the same complaint as everyone else. I have had my dishwasher since April 2013. Less than 9 months after having it the control panel went out and they came and replaced it. Now June 2015, 2 years and 2 months after purchasing and a year and a half after the control panel was replaced, none of the buttons work except the cancel button. How is it that these machines, as expensive as they are, crap out after 2 years! Such a waste on money!! Maytag has lost my business forever!!

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

Lets see... my complaints are the same as the others. I purchased the Maytag Bravos set. They were the higher end units. At first, the machine was very quiet. I quickly had a control board go out. Got that fixed. Now the washer gets off balance on every load.... Every time it spins, it stop. The gears whine very loudly... Louder than any other machine Ive ever heard. I agree with the comments on wrinkled clothes. It also does not clean heavily soiled clothes as well either. Overall, a bad decision.

Dishwasher has been very dependable. Very reasonably priced and in over six years of service never had an issue with it. It’s a little on the small side for a large family but if you’re for less in your household-- works perfect.

Purchased a new set of Maytag Bravos appliances in 2010. Washer lasted 3 years -- had a failed bearing and repairman said not worth fixing as tub would most likely also need to be replaced. Replaced with a new Speed Queen which has been operating trouble-free. Today dryer quit heating -- repair person stated it needs a new board -- not worth it to me. I am off to now purchase a new Speed Queen dryer. What happened to Maytag quality???

We renovated our kitchen in 2008 and installed all Maytag appliances. We had purchased a Maytag dishwasher 3 years prior to the renovation-- that we kept. Well, the dishwasher was the first Maytag appliance to go. After replacing several cheap plastic parts on the dish racks (I resorted to use twist ties at one point to hold the racks together) the racks started to chip and rust, leaving stains on our dishes. The cost to replace the racks was about $150 so we just replaced the dishwasher (with a Bosch - so far, no problems!)Then, a couple of the igniters on our gas cooktop stopped working. Since they were the back burners that we didnt use much, we just used a match to light them and let it go. Next, one of the hinges on the double wall oven door snapped. This is a little concerning because the doors are heavy and will need to be replaced. And the final straw concerns our French door refrigerator. The control panel started flashing wildly and the ice door was opening and closing with a loud clicking sound. Of course this happened on a weekend so I looked online and found hundreds, if not thousands, of similar complaints. So I called Maytag and spent nearly an hour on the phone only to be told that my model number was not one of the recalled ones. I explained that my problem was exactly like the others and was told that the best they could do was offer me 50% off any parts. The service call and shipping would not be covered either. The Maytag representative that I spoke to tried to cheer me up by telling me that at least they had the part I would need in stock, unlike the recalled models. Those parts are discontinued and have to be specially manufactured and have a two month waiting period. The part is about $250 and add to that the shipping and service call and I am sure this is going to cost me several hundred dollars even with the discount on the part. Very, very disappointed. Never again will I buy Maytag, never again!

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

My dishwasher is two years old and it just stopped working. I called the store I purchased it from and they sent out a repair man. He told me that the control panel was damaged and that he would have to replace it. The cost is $145.00 plus the $50.00 service call. He said something must have spilled and got into the control panel. It is a built-in dishwasher underneath a kitchen counter. I think it should somehow be protected against spills and/or moisture getting into the control panel as it is underneath the kitchen counter. I do not remember spilling anything that ran down the front on the dishwasher. But even if something spilled, if it was made properly it should still be working. I will not recommend a Maytag to anyone and will also spread the word about what happened. Unhappy in Pennsylvania.

Whirlpool owns Maytag and it appears that selling poorly made products is now their focus. When I purchased this Maytag 30 Gemini double oven range, I thought I was buying a superior product. Now, I am on my 3rd repair. When would it fail, on Christmas Eve morning when I am trying to prepare dinner for 20 people who are coming for dinner party. I paid too much for this piece of junk. From now on, I am buying from the scratch and dent sale because there are no quality appliances manufactured today. Buy cheap and it wont irritate you so much because no one especially Whirlpool owned companies focus on quality.

The Maytag Bravos XL Gas Dryer I purchased less than a year ago has stopped working three times. The dryer stops producing heat. I am now about to call Maytag repair again and waste time and energy setting up a warranty service call. I spent a lot of money in order to go to the Laundromat on a Sunday. Do not purchase this dryer if you would like to be able to dry clothes at home with any type of consistency or confidence. Arrrggg!

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

This Maytag dishwasher has been really dependable, looks really nice, is really quiet, we have absolutely no complaints. I hope it lasts as long as I suspect it will. Would highly recommend this dishwasher.

We bought a Maytag Bravos three and a half years ago. We always tried to follow instructions for the machine. Only used he detergent, used the affresh, tried not to overload the machine etc. Had to call a repairman. Our washing machine started leaking water at the bottom. Hoping that it is only a three machine it would be fixable. Bad news the repairs would be over $600.00. It needs a new tub seal and bearings. For a THREE YEAR OLD washing machine! The repairman and I had quite a talk about appliances. He said they just dont make them to last anymore and the companies such as Whirlpool, Maytag, etc. do on purpose and they get away with it. Stay away from Maytag Bravos. It is a worthless piece of crap. It will not last long. Now we have a three year old washing machine that does NOT work right. Something has to be done in this country to come down hard on the companies that make appliances. I would NOT recommend this piece of crap of a washing machine.

We have had our side by side Kenmore for years and it hasnt let us down! We eat mostly fresh food since we cook a lot and we always have plenty of space for our food. We are only a family of 2 though. They say the ice maker is the first to fail and it has not given us any issues for nearly 10 years now! Love Kenmore!

We purchased a Maytag refrigerator model # MSF25D2EAS on 10-22-2012 at the Home Depot in Tracy, CA. On 2-2-2014 (15 months) we noticed a puddle on the kitchen floor. Upon inspection, we noticed that the refrigerator was not working. Went over to Home Depot and were given the name and number of the authorized Maytag repair dealer (A and E). The technician arrived on 2-5-2014 and replaced the compressor on-off /overload relay and charged $243.82. On 2-16-2014 (11 days later), the same thing happened again. The technician came on 2-19-2014. This time, it was the compressor at a cost of $800.00 plus the $75.00 service call. One can purchase the compressor online for $300.00 and I am sure that A and E buys it for a lot less. We thought about it and decided not to get it fixed because we did not know what else would go wrong and how long would the second compressor last. We talked to the Appliance Departments assistant manager and were told that Home Depot does not give any kind of consideration and she had worked there for 11 years and had not heard of any problems. She was not telling the truth or she was not aware of the numerous negative customer reviews online. She also informed me that I should have bought a warranty. We have bought quite a few refrigerators in 50 years and they lasted for many years. Home Depot sells inferior products. Maytag must sell these inferior products at discounted prices and of course, some stores are looking for larger profits. I do not trust Home Depot any longer and will not purchase appliances there anymore. It was a very expensive lesson - the price of the refrigerator, loss of food (twice) and the stress it caused. We bought a new refrigerator at Sears and it was not a MAYTAG.

I have to rewash many load of dark clothing because pale white smears appear on the clothing most times. Ive tried various cleaning methods to try to remove any residue that might be in the walls of the tub. Unfortunately, I cant afford to replace the Maytag white elephant model 500XWZ, serial C31430894. I no longer have the receipt. Buyer, beware. No Maytags in my future.

Bought a Maytag Bravo washer, suppose to be the best of its kind from Home Depot. Should of known I was in trouble when it took them over four months to deliver it. It lasted two years before the bearing went on the machine. Whirlpool/Maytag was of no help. Ironically, the machine Im using today is my old Maytag I bought 17 years ago. The repair cost for the new machine was about 50% of the cost of the machine purchase.

We bought this brand new washing machine just 6 years ago. Went with a Maytag because they are supposed to “last forever”. Ha! Last weekend it stopped spinning. Water would drain but no spin cycle. Had a recommended repair person come out and he said it was unfixable. The bearings were shot. This is crazy. There are only two of us using this machine how could it be totally unfixable 6 after only 6 years. The average washing machine life is supposed to be 14 years. No more Maytag for us.

We purchased a washer and dryer, spent in the neighborhood of 1000.00 hard earned $$... extended warranty, the whole enchilada. Maytag. dependable, lonely repair man, ha.. that is just so much stuff. Well anyway it was a Centennial set. What junk. Never really worked that well to begin with. I trashed them both after exhausting all avenues to make it right. Well I got the hair to report the mess to consumer affairs and see if they are what they claim to be. This is more of a warning to all consumers.The stuff you consume today isnt worth the money you pay for it. The money isnt worth the time you spent to earn it. I am gonna try to find a old washer and rebuild it, and a dryer as well. Or just use solar. Best to keep the old stuff repaired and running. I dont know how many people I have spoken to about this problem. Our infrastructure is crumbling. A consumer based economy. Only there is not anyone to service the products we consume... pitiful. I guess my wife will be out back with a tub and washboard before it is all said and done... she will not like it, I guarantee that. I could not even begin to repair the washer. It was a computer operated board that did not work correctly from the beginning. The dude came out from the repair shop and fixed it while still under warranty. It died a slow painful death shortly after that. I disassembled it with a screwdriver and now have potatoes growing in the tub.The dryer has not met the same fate yet. It just sits there, anticipating the moment when I remove it and dissect it with a Sawzall. And I guarantee that day is coming. Do not buy anything from Maytag or its subsidiaries, think long term. We have become a bic lighter economy. I have been on the forefront of that movement. I did not realize it at the time. I do now. and for that I am sorry. I always expect something to work when I need it and if it doesnt, I try to repair it. Cannot fix this stuff now. The support we used to take for granted has been outsourced as well as the production of the product. Bob Dylan said it best in the song union sundown... Thank you and e pluribus unum.

Purchased Maytag 4000 series washer Feb. 26 2011 - within six months Maytag warranty replaced the drum and bearings, within another few months Maytag worked on the drum again. Year two started out with the warranty contract replace the drum and bearings again. Oct 1 2014 called for service again, the drum not moving and having to wait 2 weeks for Tech. to checkout the machine then order parts. I have 7 children at home and that didnt matter to anyone. After reading online the number of 4000 series Maytag machines with this problem somebody needs to make Maytag recall and replace them.

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

Washer purchased in May 2013 last month it stopped completing the drain and spin cycle and cloth stayed wet. To have the machine repaired, we would have to replace the control panel. The cost of replacing the control panel plus the service call was 76% of the cost of buying a brand new machine. As such we are disposing of the machine and will be purchasing a competitive product.

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

We bought the fridge (MFF2258VEW2) about 5 years ago. We have had nothing but problems. First it was the water leaking all over the floor. The repair man said the drain tube in the back was too small. That was replaced. Then the door gaskets were replaced. The doors still do not stay closed. Again water leaking all over the floor. The bottom of freezer had ice all over it. I had to take the back of the fridge and freezer. For 2 days I had a fan blowing on to defrost it. The door shelves are cracked and falling off. I had to pay for the hooks that hold up the bottom shelf 5 times and again they are broken. The long narrow slide out shelf is broken. Food in the back of the fridge are freezing. I have contacted Maytag a lot and they will not fix the problems. At the same time I bought the fridge I bought a Maytag top load HE washer and a drier. I had to throw out the washing machine last year. It would have cost me too much money to fix it. I will never EVER buy Maytag again.

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

I bought this washing machine 2 years ago or so. We have always bought Maytag. My mother still has hers she bought over 25 years ago and it still looks and works great. So my wife wanted a new washing machine so I said were going to get another Maytag. Boy did I screw up. What a piece of ** junk. Sounds like its grinding gears all the time, so loud. I close the door in the wash room and I can still hear my investment on a Maytag grinding my nerves because I spent so much on a product of a brand Maytag that I thought would be around for a while. Do not buy a Maytag.

I am so sorry to see so many people having the same problem. Maytag Dishwasher Model #MDB7749AWM2 purchased 12-10-11. Control Panel needs replaced (260.00...service call, part and labor). Writing this as Ive spent the last 20 mins on hold with Maytag. Im demanding them to make this right. Ive been told by Trisha at Maytag not to believe all these post as people tend to exaggerate the problems. Anybody have info on class action lawsuit? ?

I bought a Maytag laundry set (washer and dryer, models MVWC565FW and MEDC555DW, respectively), and I concur with the fact that this is the WORST laundry set I have ever owned. The clothes came out of the washer extremely dry and did not come out as clean as expected. In addition, clothes came out with strange spots, especially the dark ones. Now, we wash our dark clothes with fear of damage them. The dryer is also pathetic. I put in a normal load on high for 60 minutes, and theyre still very damp. Sometimes I have to repeat the cycle 2 or 3 times. When I compare it with my old laundry set, this is extremely disappointing. And to make things worse, the customer service department doesnt answer you. I sent them a mail, on February 2018, and a month and a half later, I havent heard back from them.

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

Bought this Maytag washer from Sears and the salesman told us it was the best washer on the market. Well the Maytag washer is a dud. It leave residue on clothes, clothes come out very wrinkle. This washer does not even have a filter. I would not recommend this washer to anyone. We are very dissatisfied. We dont blame Sears, we blame Maytag for even thinking about putting this washer on the market - Maytag model mav7757aww

Last week I noticed that my freezer motor had a build up of frost. I melted it with a hair dryer. 2 days later there was a layer of frozen water on the bottom of my freezer as well as a layer of water on the first shelf in the fridge area. There is no way to access the drainage tube. I thought that the coils needed to be cleaned. That was not successful either since the coils run horizontal and only the front section can be vacuumed. Today, again the freezer motor area is frosted and layer of ice on bottom and the motor is making a terrible noise. How disappointing for a less than 2 year old fridge.

We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

Like everyone else Im calling corporate. Mr Fettig he should be in hall of shame after these complaints with their defective product. My fridge leaking, ice maker broken, water everywhere and eight inches of ice. I wonder if he owns a Maytag himself? Oh well after a while he might have a flood on his floor. This should be recalled just like my first model in 2001 that was a fire hazard. I had to go to the top then and I will now also. We should be protected from buying garbage while he makes 4 million a year.

Purchased a supposedly top-of-the-line Maytag washer and dryer (9000 Series with Steam and MCT-Maytag Commercial Technology; Washer MHWE900VJ). Just under five years of use and the repairman quotes me just over $1000 parts and labor with the overwhelming majority of that quote being parts. No wonder the Maytag repairman is the loneliest guy in town - its not worth fixing your not-yet-5-year-old machine. It kills me that companies are allowed to advertise and promote the quality and reliability of their products and less than 5 years later, the machine is going to the dump, after having paid a premium for quality. This technology was supposedly comparable to what is used in a commercial setting - not very believable in my opinion. No more Maytag or Whirlpool for me.

I purchased this Range about a month ago and would return it to the store if it wasnt such a hassle. The set of grates that came with had 1/4 drop from the center to front of stove. Whirlpool sent a new set; they were no better. Then customer service wanted to send a Tech out to see if the grates were out of spec. If they are out of spec they will replace. If not I will be charged $89 for a service call. Whirlpool customer service assured me their service rep would have new grates on his truck. So I drove to their service provider, he laughed and said imagine they want me to send a service Tech out to look at cooking grates and NO they don’t stock them. If you want a cooking surface that is level and does not SCRATCH BOTTOMS all your cookware. The convection oven is also a joke. In order to bake something in the specified recipe time, I have to set bake temp 25 degrees higher to compensate for convection ovens automatic temp set back feature. When I turn on LF burner flames engulf 10” pan, a truly fire hazard. I have a Maytag dishwasher and dryer, love them both. Maytag should stick with dishwashers and laundry. I never have been more dissatisfied with a major appliance. I would NOT PURCHASE THIS PRODUCT.