I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

I purchased a Whirlpool oven. It is still under warranty at present. I used the self-clean oven feature just before Christmas, it wasnt that dirty but I wanted to have it clean for Christmas. The glass panels on the door had no stain or grease on it, until I used the self-clean feature, and now there is black staining inside the glass. This oven is not even 9 months old, and you cannot clean in between the glass. My second complaint which I believe is a very poor design on Whirlpool’s end is that the steam vents are very sharp. When I went to wipe off the black splash panel just under the vent tube, I cut my baby finger twice!!! And it is impossible not to slice your pinky. I have been working with Whirlpool since this happened, and they finally issued me a new stove. I was to go back to where I purchased this product and pick another stove. So I did this yesterday and checked out all the Whirlpool stoves because the store says I have to purchases a Whirlpool. But every Whirlpool model has the same sharp steam tube vent, and I am presently waiting for the store manager to speak with his higher ups to see if they will let me pick a stove made by a different supplier. I’m actually really shocked to learn that this could end up being a battle especially after I took the manager to every stove in his store made by Whirlpool and showed him each of the vents and just how sharp those vent tubes really are. You would think he would want to be aware of this and deal accordingly. So I post this to warn any potential customers of Whirlpool to check that steam vent on the left side of the stove, and stay away from it as it is very sharp and you can’t help but cut your pinky finger when you wipe across the stove.

For families where people work in gardens, work on vehicles and get just plain dirty doing things anywhere outdoors these agitator-less machines are not for you or me. Ive had mine for two years and I truly dislike it (Model MVWC425BW1). With different products I scrub dirt and grease stains on pants before they are put into the washer, scrub again when they come out of the wash and then scrub and wash again a few more times but I cannot get all the dirt out. I now work more on laundry and harder since I got this machine.This agitator-less machine is designed for people who dont get really dirty - just remove everyday perspiration and household grime. I think this machine was designed by engineers who have never done daily laundry for any length of time and theoretically thought it would clean really dirty clothes. They were really wrong! Having done laundry for 50 years, I now know that an agitator cleans better. It would be nice if other women and I, who have done laundry for years, could be on focus groups about developing new washing machines.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

A contractor purchased the Maytag MDB7609AWW2 dishwasher about two years ago. Sometimes it will start a load, but most times it will not. The light for high temp, heated dry and sanitize work, but the heavy, normal, light indicators will not light up. Im faced with either replacing the control board or control electronics. I was told Maytag is a quality product. I have not abused the product. The last dishwasher that I had lasted 10 years. I only purchased this one because of a remodel. I will most likely replace the control board since thats the defective part. It doesnt give me a good feeling about replacing the part since it’s obviously a defective part. I will consult Consumer Reports before purchasing another dishwasher.

Bought a Maytag dishwasher 2011! Use it 2 weeks, digital board went down had it replaced! Now 2013, the board is down as well as the motor!! Can you imagine I use it once a day, at most 2 people in this house, and it completely breaks down! Thank goodness I have a Home Depot warranty. I would strongly advise against this product that I spent over $500 for 2 years ago!! How they could sell this dishwasher is a mystery.

Second time I have purchased a Maytag washer. Both units failed within six months of extended warranty running out. Maytag repairman is sitting on his **, not because they have a quality product but because consumers are seeing that it is a subpar product. Don’t waste your money on them or any of their off brands.

We had Maytag brand washer and dryers in the past. They worked for years and I was able to repair or replace switches and some parts on my own. The new Bravos XL is a very inferior machine, nothing but problems. The clothes have to be washed two or more times to make them clean. There is no agitator, so your clothes have only other clothes to scrub up against, and the spin cycle is just thumping and banging and thrashing around until you’re able to get in and rescue it from itself. Our older machines had tiny steel shot in the rim of the machine to keep it balanced. Don’t buy this machine ever!!!

I purchased a Maytag front loader washer less than a year ago. Based on their deceptive advertising, Maytags rarely need service (model MHWE201YW00). There was a loud banging within 11 months. I called service for the additional warranty I purchased. The service man told me this machine is shot. The bearing completely broke and the drum was loose. They ordered 3 huge boxes, 3-1/2 feet cubes delivered to my house. I had to drag them into my garage where they have been sitting for two weeks. I am now 4 weeks without a washer with 4 kids. Ive called Corporate Headquarters and have spoken to their Corporate Board Gwenn and Jackyln who seem to think they can diagnose the problem. I told them the machine smelled like it was burning and the last load was dripping wet and the clothes smelled burnt. This is a stackable in my kids bedroom and I told them I was concerned about an electrical fire. Ive already missed one day of work for this. I am now being told Jan. 11, 2013 is when it can be serviced. That would be 2 months without a machine. They are willing to endanger my children with wet wires and an electrical fire. Mr. Fettig is impossible to get in touch with and this customer service center apparently has no supervisors. What they say, goes. A class action should be started against Mr. Fettig and his team of crooks who are putting crap out into the market place, falsely advertising it and then not backing up when their product breaks less than a year and becomes a possible hazard in someones home. Ive sent to his home address a UPS letter to Mr. Fettig, letting him know if a fire starts in my home due to water on the wet wires (water that got behind the drum because of the faulty bearing), water that was leaking from the bottom of the washer that I hold him and his company personally responsible. They have been alerted to the problem numerous times and ignore it. I spoke to their Safety department and I asked what to do if I smell a burning smell when the machine was running. They told me to immediately shut it off and unplug. Yet Whirlpool is trying to put a Band-aid on a machine that has already been infected with water damage to the wires. This has been such a frustrating, stressful experience. Even 5 weeks from now, when my replacement parts are put in, I will worry each time the machine is run if there will be a spark from the damaged wire. Something must be done legally to stop these crooks from doing to this and getting away with it. All they care about is their profit margin. The Whirlpool creed to their customers is a bunch of bull! Mr. Fettig vacations at his home on Dolphine Island, Alabama while hardworking people are scrambling around trying to figure out what happened to their new appliance that promised to work but is broken in less than a year. He vacations at his home in Florida while the hard-earned money you spent on his product is a waste.

Maytag Bravos 300 Washer - Dont buy this washer! This expensive washer has been the worst household appliance Ive ever owned. We bought Maytag thinking we were getting the best. NOT SO! We could have spent half the money and got a better washer. Maytag is a brand of the past. Ive had this machine about 4 years and its been a problem since day 1. There is no soak cycle but I knew that from the beginning. The problems Ive had so far are: Not enough water so items dont get wet and have to wash again, Terrible wrinkles, torn sheets and garments, items still dirty, getting louder & louder, and the most recent problem is the plastic from the top edge of the tub is now shredding and getting sharp plastic pieces in my clothes.

I purchased a Maytag dishwasher in 2013 and the control panel needed replaced within the warranty period. About a year later, the control panel started to malfunction again, this time out of warranty and Im told it will cost over $350 to repair. I paid a lot for this dishwasher and thought I would get years of use out of it. I plan on buying a new cheaper one (not Maytag) for a little more that the cost to repair the Maytag. Im very disappointed and will not purchase another Maytag. I also read online that Im not the only one experiencing this problem.

I bought a Maytag dishwasher (MDB7749SBM) and 1 yr and 4 months the control panel went out and all Maytag would do is tell me that they will pay for the parts, and I have to pay for the labor. I remember when Maytag had the best Warranty on their appliances. I am very disappointing with paying for labor. They also offer an extended plan of $269.00 for a year. What a joke!!!

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

First we bought the washer and not even a month after it was ruined. In the span of the year that weve had it, it has broken down about three times. Then we bought the matching dryer in August and by the beginning of December it has broken down. Called customer service and they are not coming until January 18. Have me waiting over a month to fix it. Worst brand ever and even worse customer service. Never again will I buy anything from this brand.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

Washer goes off-balance even when clothes are evenly distributed in tub. When it is turned off to rearrange clothes (which may have to be performed a couple of times), washer goes back to starting cycle which means more water. Afraid to do laundry unattended.

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

I bought my Maytag Neptune washer and dryer in 08 or 09, and it has smelled like mold and mildew for years but I still have to use it because I cant afford to get a new one. I cant get the smell out. Also, I have to take the pump apart at least once a year due to the fact that sometimes, no matter how you check your pockets, change still gets left behind and they dont make a screen or filter that will keep the change out of the pump. It is not hard to do, but the first year I had it, it were in the service center as much as it was home. I was glad when someone told me what was happening because I fix it myself in like 15 minutes and move on. But it should come with a self service manual showing how to do this procedure to save people money.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

Maytag ser5000 washing machine from hell. When called the customer-service stated over the phone there is bearing problem. When the service-man show up, took one look (approx 50 seconds) at the washing machine (which only 4yrs old), stated he is not touching it and not worth to fix it - get this! Due to bearing! Charged me $200 as standard fee. To put salt on the wound, service-name stated: Ive should told the customer-service bearing problem which is very well known by Maytag! Therefore, save my $200. Note, I will NEVER buy Maytag appliances!!!

I love using my microwave because everytime I am in a hurry, like going to work and my kids to school and dont have time to cook or we dont like to eat outside fast food I cook healthy the night before and microwave it the next day and it just feels like the food is just made. It taste so good my kids and husband love it.

I bought Maytag frost-free refrigerator last August 2006. But now, I noticed that ice builds up in the freezer. The product is only five years old but I was told by Whirlpool that they had discontinued making defrost heater. The reason why I bought Maytag was the ad on TV showing the Maytag service technician seating and doing nothing, implying that Maytag brand is a good product. Think again before buying Maytag products.

I would have given this washer/dryer a 0 star, but wasnt able to. Bought the pair and first thing, couldnt get enough water in the tub, clothes wallowing around for an hour in the few cups of dirty water that it allows. Cant even believe how terrible this combo washer and dryer is! Now I get to wash everything in this piece of ____ twice, thank you Maytag! Just took out a load and it is dingy and stinks, so now its wet, on the floor waiting its turn to go back for another wash (possibly even a third).If you want clean clothes, do NOT get this washer. Dryer has issues also. For whatever reason, the AF signal has been on for a couple of months. Turn it off and back on and its okay for a bit, then back on. Its the Air Filter. Its not plugged, so I dont know, I just keep using it with intervals of resetting it altogether. What a total waste of money. Am going to give it away for free as soon as I find a replacement! Save yourself a huge headache and look elsewhere than Maytag. Oh, and if Maytag happens to read my review, you can contact me for a refund any time, just respond to this post, you can even come pick it up and get it out of my home. Thanks a bunch!

This washer is a piece of expensive junk. It was used sparingly (2 people using it) for 16 months when a repair service had to be called. The estimate to fix the machine ($980) exceeded the initial cost. It did not clean the clothes adequately when it was working. There was a powdery substance on the clothes when they were removed. The clothes were always bunched up and intertwined. Only the proper type and amount of soap was used. I cant recommend this washer to anyone. We were very disappointed since we have always purchased Maytag washers/dryers. Never again.

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

Bought a new Maxima washer in January. Worked for one week. Got error codes and electronics board shut down. Contract serviceman says board should have reset after turning off. Ordered new board and it is missing one of the electrical wire connector plugins. Maytag/Whirlpool is having a problem with these boards.Three weeks without a washer. Two days off work. When it goes out again, days off work will be close to what I paid for it. Thinking I may cut my future losses and buy another brand when in-transit board goes out.

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

Recently purchased a washer from Home Depot. Machine is now on its 3rd repair. The wiring harness is fired. Could have caused a fire. Now they still will not replace and part is on order which will take 4 weeks to be in stock. I called Maytag and expressed my concerns to which they could not help me as every washer is theirs can be repaired. I really don’t understand what happened to making things right. Very frustrated that they will not repair or reimburse for that matter. Please refund my mom and pick it up.

I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

I purchased my which I thought was a stainless steel French door refrigerator in 2011 that I was getting a great product. Not even 3 months later I was using my warranty to stop the leak from my freezer now. Mind you, I paid $1500 so I got it fixed. 3 months later I called for repair again... Getting annoyed because this time the freezer came off track. 6 months later were chopping ice chunks up to stop the leaking on the floor. This lasted until last October keeping towels and old clothes around the fridge to soak up the water. This is so embarrassing especially if you have company over. You have a pile of crap soaking up water. I am a wife and mother of 7 children. I cant afford to just go buy another fridge. This isnt fair... I spent hard earned money on that magnet attracting stainless steel fridge and Maytag could care less. Im so disappointed and broke. Now I have to scrap it.

Same issue as everyone else. After about 15 months the control panel on my Maytag dishwasher model#MDBH979SAM1 has malfunctioned. First it would only let me choose the rinse option but now all the lights are turning on and the dishwasher will not stop washing but yet the dishes are still dirty. I called Maytag and they quoted me 249.00 to fix the issue. But if its a common problem with this make and model why do I have to pay to replace the panel. They should recall this model or replace the panel with an updated one that wont have the same issues! I cant imagine paying 249.99 every year to replace this panel that seems to malfunction no matter what you do!!! I paid around 550.00 at the home Depot for this dishwasher! It did not even last me two years!!! I want a lawsuit filed against this company and I want my money back or my dishwasher replaced with one that works and wont have the same issues!!!

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

I attempted over and over just to swap out washing machines. I originally purchased a washer and dryer because of a defect in the top load they delivered. They talked me in to the frontload Neptune instead. Within months I started having daily reactions to mold and to my disgust found out it was from my washing machine. I begged to switch back to the top load I originally ordered and the store would not let me and referred me to Maytag who sent me some tablets and would help me no further. Apparently, the Maytag repairman wasnt lonely anymore if a product had to be manufactured and ready for complaint calls. Well I used the product. I used vinegar and baking soda. I have used hot water and bleach. I have left the door open to dry...It is the most cared for item in our family and the one that makes me ill literally. I cannot afford to buy a different one and would be interested to know if my husband’s declining health issues have anything to do with our mold issue or if it is just depression...Anyway, I was very discouraged to find out that other people in other states had washing machines replaced, but why didnt I? I would be happy if they could buy back my old Maytag that I had prior to this Neptune, I am sure it is making someone very happy somewhere. Why couldnt they have respected my very true complaint? I was not trying to get something for nothing. I paid for something to keep us cleaner and free from allergens and instead wash my clothes in mold and have mold spores leaching into the air in my home. Please help.

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

I purchased a washer and dryer model MAH8700AWW. In 2005, I purchased the extended warranty. In 2009, I had to replace the main control board and motor on the dryer. Now, I find out that the washer has a warped drum which caught on the door boot and messed the shaft up. I didnt know that it has probably been that way since I purchased it because every time I washed clothed, I had to stay in with it because when it would go to spin, the washer would walk out into the middle of the room. I called about it and they told me to put rubber pieces to hold it still. Now it is going to cost $ 821.95 to fix. That is more than I paid for the washing machine and Maytag will not help to fix it. I would like someone to contact the company and find out why they dont stand behind their products anymore.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

Maytag Bravos 300 Quiet series - Ive owned this washer for about three years. On average, I do 2-3 loads of laundry per week. I follow the loading directions, but still have to babysit the machine because of uneven load issues better than 50% of the time. Many times, clothes come out full of lint, even after running the clean washer cycle. This is the worst washer I have ever owned. Ive had better results from second-hand machines.I havent bothered to contact Maytag because Ive had it so long. Im almost to the point of getting rid of it and buying one that gets my clothes clean and isnt inclined to push the clothes all to one side and put the machine off-balance. To say Im disappointed in the product would be an understatement, especially since I paid $800 for it.

I purchased this washer in April 2017 from H/D. The machine started making funny grinding noise over this weekend. Had a tech come to house to repair. Tech said the insides are stripped, 300 plus in parts to repair and would be weeks to get parts. I called Maytag and they offered to send their own tech to see which parts and if any of them would be under warranty at a price of 109. I explained that I had an expectation that a washer would last longer than 31 months and spending another 109 dollars would be bad money after good with the 80 dollars for my tech. Maytag said take it or leave it. I am going to Lowes for a GE machine. DO NOT BUY THIS. IT WONT LAST. I will admit, Tina from Tennesse, the Maytag customer complaint person was nice and professional but not actually empowered to do anything to help. I will recommend to my 5 kids never buy Maytag.

MODEL # MDB4949SDMO. Purchased Maytag Dishwasher. 07/2014 stop working. I have purchased a Maytag Washer also. It also did not last two years. I am very unhappy consumer. I will not purchase another Maytag appliance. Stop selling these lemon appliances. Need to repair free.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

Same thing as everyone else. The motherboard/control board, the main face of the washer went out and this part isnt covered on an $800 commercial washer after only 3 years of residential use on a commercial washer. Menards refused to swap it out, saying this is Maytags issue. Maytag boasts their 10 year warranty and labels it right on the motherboard as a 10 year warranty, but the motherboard isnt covered? If the main computer isnt covered, What is covered? Just screws? I called Menards and got nowhere. Called Maytag and held for an hour then had to hang up so I can work. The warranty is extremely misleading and is the reason we bought this particular washer, because it says 10 year parts warranty right there, but Maytag conveniently doesnt consider the main control board a part.

I purchased my Maytag Bravos from Lowes in early 2014. A few weeks after the motherboard fried and Lowes replaced it with a new one. Within my 1 year warranty the new machine had another fried motherboard. Maytag replaced it for free. Now less than a year later the motherboard is fried again. Needless to say I just purchased another washing machine. Definitely not a Maytag. Now I just have to deal with a dysfunctional piece a junk for a few days until I get my new one. After reading all the complaints on here and other sites, Im very disappointed with Maytag. These machines are obviously lemons and any good company should recall them. Mine will be going straight to the junkyard. I have no interest in having a washer that breaks down every 10 months. Definitely the last thing I will ever purchase from Maytag.

My husband and I bought a set of Maytag appliance 12/2011 the washer squeaks real bad on spin cycle and now today the dryer started making real real bad squeak sounds to the point I can not use it!!! My appliances are only 4 years old!!! And we wash clothes once a week for just my husband and I. I would not recommend buying any Maytag appliances!!! They are supposed to be the best but are not worth **!!! And I called Maytag, they are not willing to help. Bad service!!!

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

So this washer, Bravos MCT cleans good not great. Saves water but clothes dont always come out clean or smell fresh. We have had it for just over a year and the control panel stopped working. Warranty is good for only 1 yr. UGHH!! It is all one unit so the complete circuit board had to be replaced. Half the cost of this washer new! I saved money by replacing it myself. Took 15 minutes. Very easy. Disappointing when you see this is a come problem with this model.

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

This dishwasher constantly has an odor. I run the dishwasher every third day (there are only two of us), and no matter how well the dishes are rinsed off, there is an unpleasant smell whenever the door is opened. Even after running the washer, upon opening the door an unpleasant scent still lingers. I compare this washer to the Kenmore I left in my previous home and this brand new one falls short. I would not purchase this dishwasher again. But because this is only a year old, I guess I am stuck with it for a while.

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.

I bought this washer (Bravos Washer Model MVWX655DW) in June 2017. My wife and I did plenty of research and only complaint at that time was that it made load clicking noises. We bought it and it worked fine but never really filled with water to a level which would cover the clothes. Today I ran a load and brownish water was seeping out from underneath. When I lifted the machine my floor was covered with old stains which looked like oil or grease. I called a local service company and when they found out which model I had they refused to look at it. They said that particular model was known for having issues and when they fixed it, something else would go. They recommended looking online for reviews and calling Maytag.I did so and after explaining the situation to Maytag, they offered to send a technician to look at it to diagnose, not free of charge of course. While I cannot tell you avoid a particular company, I can say MY family will never buy Maytag again. If a washer is well known for having issues within its first 3 years and a company will not try to make it right simply because theres no recall on it I will spend my money elsewhere. Seems fishy that this machine has a ton of 1 star reviews within the last two months and Maytag does not want to eat the cost of servicing their junk.

We bought a Maytag dishwasher March 2012 and the unit wouldnt turn on October 2013 - 6 months after the warranty ended. We called their service department and they told us to unplug the dishwasher or turn off the circuit breaker. We did so and the unit still would not turn on. We called a repairman who advised us that the touch pad was not working. The cost with parts and labor would be close to $300 which was more than half the original price. We repaired it and I sent all the papers with a letter to the consumer department and today I got a call advising us that they would not do anything. Do you think I have any further recourse? If not, I will never buy a Maytag product again and will advise anyone within a listening area as to how we were treated.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

My washing machine was noisy from the start. We had recently purchased a new fridge and were told when we questioned its noise thats just the way they are. So we didnt question the noisy washer as we should have. The noise got louder as time went on and at the 18 month mark, it was so bad, we had someone look at it. The washer had never cleaned as well as expected, but again, we were too busy to follow up. The repairman advised that the bearing and tub needed to be replaced! Augh! $450 for parts $300 for labour! I contacted Maytag/Whirlpool and was advised they would go good for the parts, I would have to pay labour. Not being terribly impressed, did a bit of research and was told it was worth fixing. As it was technically out of warranty, I was lucky to have them pay for parts. Took 6 weeks to get part. In that time, had questions about delay, etc... at one point was yelled at on the phone by Melissa from Whirlpool as I asked to speak to a supervisor. So fun :( First part comes and it is defective, luckily there was another one in Vancouver, so only an additional 4 day wait. My machine is now fixed. It is extremely quiet and cleans very well. Suffice to say, it was defective from the start. So, Ive gotten to pay an extra $300 over retail to have a working machine! Lucky me! Repairman also advised that he recommends everyone to purchase the additional 5 year warranty as the manufacturers are now only making machines with a 7 year life expectancy and I was VERY lucky in the beginning to get someone to even talk to me after the 1 year mark.

We purchased an entire suite of Maytag kitchen appliances in September 2014 at a cost of $4300. Have had problems with every single item. The MMV5219DH microwave was the first issue. After a year it began to give us erroneous display messages when we tried to use it. We would input the number of minutes we wanted the food to cook, and wed get a message saying CHK TIME/OPEN DOOR. Repeated door closings, resets of the time, etc. did nothing. Sometimes if we hit cancel it would work - other times not. Wed push every button on the keyboard and eventually wed get it to work - perhaps 10 minutes later. When I called the appliance store (Vics Appliances in Saco Maine) I was told to unplug it for an hour. Okay, that corrected the issue - for a few days. When the problem continued, sometimes unplugging it had no effect - other times it did. Eventually we figured out if we didnt reset the clock time it would work most of the time (not 100%). The Maytag refrigerator began to malfunction at the same time (not keeping temp, and the ice in the icemaker melting and refreezing in a big lump that blocked the door water/ice dispenser) so we called Vics again and set up a service call. Serviceman reset the microwave to factory specs and we will see what happens. He also reset the fridge to different temps, and 2 days after his visit it has again melted the ice in the icemaker and formed a blob at the bottom. DO NOT BUY MAYTAG!!!

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

In the last 6 years, Ive had a Whirlpool dishwasher that the motor seized due to poor design and overseas Asian motor builder (3 years of normal service). I cleaned the motor and it seems to barely work another couple of months but the design and manufacture process was garbage at best. Thinking I would go with the best produce MAYTAG (Old commercial about repairman having no calls), only to find out that it too was bought out by CRAPPY WHIRLPOOL and it too lasted a couple of years with cheap MADE IN CHINA electronics!!! Thats why we are the laughing stock in the world as far as products.I remember the days of where built in the USA was the best of the best, now with selling our great nation down the toilet so some Wall Street Commie can make his/her biz-zillion dollars and sell this nation down the toilet. Maybe they need to go down to Arlington and see who really has paid the price for their luxurious life-style!!!

Maytag water efficient, no central spindle top load. Clothes come out with scum on them. Really a problem on the solid darks. I have to scrub with terry cloth to remove. Maytag insists this is normal. Refused to honor warranty. Usually check Consumer Reports for quality and best buy. Energy/water efficiency is important. I like to have some control over the machine so that I can use it the best way for me. Such as soak. This machine cannot be manually controlled at all. Also it doesnt have a lint catcher, doesnt filter the wash or rinse water at all. All the lint and pet hair remains on the clothes or even gets worse.The clothes are not clean. I have no way to control the machine for my use. It may be water efficient but seems to use too little water to clean the clothes. Maytag wants to blame the EPA - This is irresponsible on their part. Its an awful washing machine and they made it. Maytag continued to insist that scum on the clothes was working normally. This scum was added by the machine. I used very little detergent; the clothes were relatively clean - just lightly wore a few days. They come out of the machine with streaks of white scum that I have to scrub off. The clean the machine cycle uses a huge amount of water. This is really DUMB: washing the machine instead of cleaning the clothes! Terrible! And Terrible customer service at Maytag. DO NOT BUY MAYTAG.

I purchased the Maytag Bravos washer and dryer set one year ago, and have asked myself why ever since. The oversized laundry tub is what attracted me to the model, but it sure doesnt deliver for the money it cost. On normal settings, it doesnt use enough water for all the clothes to even get wet. After the load was complete, there were areas of my clothes bone dry, and obviously still dirty. I soon learned that the only way the washer uses enough water to get all the clothes wet and clean, was to set the machine on the bulky setting. This is the only setting I use now, but all of my clothes winds up twisted together, sometimes in one big ball. As for efficiency, that statement folks is a joke! Because I use the bulky setting, it uses much more water than a traditional washer ever did, and when the load is off balanced, it will go through another rinse cycle to try to even it out. This machine uses far more water and electricity than my old school set! I suppose if you dont get your clothes dirty, you may not need to use the bulky setting, but thats the only way I can wash my laundry with this machine. The old style set I had before this was Maytag also, and lasted about 20 years. I was more than happy to purchase Maytag again, but this set has been nothing but a disappointment. I dont plan to buy another energy efficient machine again, nor would I recommend this product to anyone!

Never liked this machine. No flexibility in settings, ruins clothes, noisy and often shuts down. But main concern in the fact the whole top is rusting by the bleach dispenser and it leaks from the top all over. It is only 3 or 4 years old. Can not believe an expensive product like this can be so bad.

We purchased a Maytag Jetclean Plus Dishwasher in June 2013. It worked well enough initially. We bought it because it had a large capacity and built in disposal. By August 2014, just after the warranty expired, the front panel gave out. To have someone even look at it cost $150. By following instructions from internet discussion groups by other people facing similar issues, we were able to get it to run in random mode. Programs were no longer indicated or selectable but dishes generally still got cleaned. Two months later a wheel fell off the premium rack glides. Finally after about 2 years of use, the dishwasher finally gave up altogether. At this point the stainless steel tub is no longer stainless. The entire device has worn poorly and looks shoddily made. This is the worst use of $900 I have ever made, and what tweaks me the most is Maytags attitude and their ludicrous warranty that barely lasts out the weakest link in the device.

I purchase the Maytag dishwasher Model: MDB7749SBM from Home Depot in Plano Tx around June of 2013. The start/resume and cancel/drain button lights either flash or wont turn off and keeps trying to restart the wash cycle. I have only had this DW for 1 1/2 years. That’s pathetic! I went through the manual and tried everything it recommended but it didnt work. So far the unit still cleans dishes. Based on all the reviews I have seen on these Maytag dishwashers with the same issue, you would think there would be a recall. All the appliances in my home are Maytags and Whirlpools. Maytag and Whirlpool are now the same company. Depending on how they handle this issue will determine which appliances I buy in the future.

This washer has been the biggest disappointment of any appliance I have ever bought. Purchased 12/2012 and immediately disliked it but thought I needed to get used to the new style since my previous machine operated for 23 yrs! It is loud and does not clean as effectively as my last machine. It stays in the Sensing mode for 15 mins or longer. Rarely will it spin as it should. Most loads, after the sensing stops and the lights go out, I have to move the dial to Drain/Spin, wait for it to sense again and then maybe it will spin. If this doesnt work I have to unplug the machine to allow it to reset. I called Maytag and was told there are no known issues with the machine. I google this model and find many customers have had a similar problem.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

Maytag dishwasher does not clean dishes. It has hot water and we have had a repairman look at it and he said water jets working. We have to wash all our dishes by hand before loading them into the dishwasher to sanitize.

The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

I am a Baby Boomer... just like so many of us, I watched those lonely Maytag Repairman television commercials. Yes, silly me I purchased our top loading Maytag Bravos XL because of the brand name and because the machine was large enough to wash our bedding. Well, like so many fellow purchasers have found, this machine does not get the clothes clean and leaves soap spots all over the clothes. Its embarrassing. Additionally, there is that funny smell after the clothes come out of the wash. Well, Maytag has really done a number on us all. Kudos to their research & development department for creating a washing machine where the clothes come out dirtier. Has Maytag thought about a RECALL? I will tell everyone I know to NEVER buy a Maytag.

PURCHASED WASHER FROM LOWES. IT STOPPED WORKING IN 2 WEEKS. CALLED MAYTAG FOR SERVICE. First repair service wanted to charge me. Next repair company Rawlings made 2 visits, looked at washer 1st visit said they had to order top latch. 2nd visit need circuit board. 3 weeks passed no latch, no circuit board, nor repair service. DO NOT BUY A MAYTAG WASHER.

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

My washing machine is a Maytag Ive been using for over 27 yrs. I love the older, top loading machines because I like to take certain items out after 5 or less minutes. I now live in an apartment & wont use their machines! Thinking about a stackable for my personal use. I am quite fanatic about laundry & do a lot of items by hand.

Purchased a new Maytag washer and dryer in November 2015 after having a old set not Maytag for 25 years with no repairs. WOW. Then the new washer went out in Feb. 2016, now the dryer in May 2016. Very unhappy. Is it because the machines are now made in Mexico? Cheap labor and cheap parts. ICK!!! Thank god for the extended warranty.

My husband and I purchased a Maytag stainless steel French door/freezer bottom ice making fridge from Hhgregg in Brown Deer, WI and 8 months later (now), Ive been told that my food that is spoiled, cant be replaced and my service for the fridge wont be done until next week! I have 5 kids and a husband. This has turned our world upside down. I called them and spoke to a Nicole and she said they cant do anything for us, but we can try to contact the diamond repair service at 269-927-2519 to see if they can get us in sooner. I asked for a refund for the fridge and she said no, the 10 warranty only counts for repairs... I am so angry that I didnt research Maytag before now. I gave the Whirlpool fridge to the delivery guys of Hhgregg and I had that for 18 years and it never went out on me. If anyone is reading this and is upset as well, let us get together and start a class action suit!

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

I purchased a 2011 Bravos top loader washer machine. Doing a minimal amount of laundry for 2 persons, the Bravos is in disrepair needing bearings and an inner and outer tub. I was told to purchase a prepaid service call for $350 that will cover repairs plus a mere 1 year additional warranty. The washer sounds like a jet plane, gives off fouls odors, has black tar like residue after each wash and clothes never smell clean. Maytag has no complaint process, except an online chat that tells you to buy the prepay. Maytag has dumped a lemon on consumers and arrogantly expects us to pay for their garbage. They are disrespectful, dishonest and greedy and dont deserve anyones hard earned money for their ill made products.

We bought a Maytag gas range in Feb of 2011. Shortly after that, we started having an intermittent problem with the oven not maintaining the temperature. It sometimes would not heat up to the proper temp or sometimes would get there but not maintain it. We have had several service calls all for this same problem. Each time they would replace things... nothing worked! We called Maytag and they said they wouldnt replace the unit until the same part had failed 3 times. Well, the service company came out 5-6 different times in the first year and replacing the main panel twice and the sensor and some other thingies I dont even remember. Pretty soon the warranty was running out, so I bought an extended warranty due to the fact that the unit had never been fixed. They sent out two different service companies who also were unable to fix the unit. It is now 18 months since we bought it, and Maytag refuses to do anything since it is out of warranty and the extended warranty company will only replace the unit up to 75% of its cost. So yes, we are very angry with Maytag and the way they wont stand behind their product and their total disregard for their customers.