My washer is 3 years old, it sounds as though an earthquake is rocking my laundry room during the addition of water, rinse, and spin cycles. Cleanliness only when washed twice, along with the washer stopping at 12 minutes because of UL signal (unbalanced) - this happens even when I have a small load. The dryer does dry clothes however along with tons of Lint stuck to my clothes. I empty the lint screen after EVERY dry cycle. Have had repairman who charged me $70.00 and said he could not fix the washer.

We purchased a gas range and over the range Maytag microwave a few years back and have had problem after problem with the microwave. Weve had 3-4, maybe more, repairman here and they replaced pretty much everything. Its been going for about a couple years now without a service call, but it went out again today. Very frustrating when you spend good money on junk. We are now to the point that we either replace it with another brand or we just put in a hood and have a microwave on the counter. Just so frustrating. I would not recommend Maytag over the range microwave to anyone!

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

We bought this he Maytag washing machine about 3 years ago. I have hated it from the start and should have put a review right away because it is a piece of cr#&. It does not save any energy because I have had to rewash loads because clothes come out still dirty, lint still on them, sometimes even dry spots on clothes. I did a wash today and chunks of HE detergent still in the clothes. I am rewashing a load right now. I now have to do a presoak hoping that will help the load come out cleaner. So dont waste any money on Maytags HE machines as I will never buy another one.Being an environmentally conscious person, I thought HE was the way to go but it doesnt save any energy when you have constantly run a laundry twice to get clothes clean. It also does not do a good job spinning as clothes are still very wet. I hate this machine and I am thinking about junking it even though it still runs. Very bad purchase.

I had a 30 year old Kenmore large capacity washer that finally gave out. I began a lot of research on who makes the best washing machine now. I used Consumer Reports, appliance websites with reviews and finally decided on the Cabrio. Let me say, I had no idea that I would be able to add extra clothes to the wash load and come out with clean clothes every time. I am amazed at how they are practically dry when the cycle is complete. I do have to run a cleaner through my machine after so many washes, but it is so much more efficient than my old Kenmore was. I cannot complain about it though. It lasted 30 years and that is unheard of now.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

My Bravos 300 series is 3yrs. Initially it occasionally shredded an item. With 4 kids I chalked it up to wear & tear on the clothes. Its now ruining items almost every wash. I now wash much by hand. Cant wait to afford a new one.

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

Nineteen months in a home of empty nesters and the darn thing is a game of trying to outwit its electronics. We live a long way from town, which makes service calls a high dollar thing. I have spent considerable time this weekend trying to cipher its moods and order parts. This washer was purchased on an invalid reputation. Others beware.

This washer (Model# MVWB765FW1) will not wash your clothes. Its not designed to give enough water for washing. That means some clothes will still be dry after agitator cycle; seriously. Thank you Maytag for going green! The repairman will tell you the machine is working according to design. That is true but the machine is a fraud as a clothes washing machine. The weight of the clothes in the tub tells the computer how much water to apply; good luck with that. We learned that if we add a bucket and a half of water, the clothes will come clean. Do you want to do that? Maytag used to be a good name.

I bought a brand new Maytag bottom freezer fridge on Aug. 12th, 2012. The main compressor went out on Memorial Day of 2013. I contacted the store I bought it from; they referred me to a local repairman who fixes Maytag. I talked to him and told him the problem along with the make & model of mine. He ended up telling me what exactly the problem was, & there were about 5 people ahead of me with the same fridge, & same problem... all main compressor problems. Check this out. The compressor part is on back order... so now I have no fridge, & Im stuck with this piece of crap, until MAYTAG finds a compressor to ship to the local repairman. - Last Maytag product I will ever own in my lifetime!!!

Purchased a Maytag dishwasher in 2009 then had it repaired for a leak in 2010 (just past the 12-month warranty); next another leak in Nov 2013 so purchased another Maytag as repair appliance company said it wasnt worth fixing. Now in Feb 2015 it is leaking Again! So 2 dishwashers and 1 repair in 5 years! Both were purchased from Home Depot. I will Never buy a Maytag product again.

This has nothing to do with the vendor. This is clearly shoddy workmanship on the part of Maytag. I bought this refrigerator in 2005 and already the compressor is gone. So therefore, I have to replace the whole unit.What kind of ** is this? You mean to tell me that you people cant find someone to build a compressor that holds up more than a few years? Why dont you try American made and built.I am disillusioned by the whole industry. Im sure the people at the top could care less.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

I purchased my Maytag MDB7749AWM2 dishwasher approximately 3 years ago. Since it was stainless inside and out I felt that I was making a long-lasting purchase. The handle on this particular model doesnt have a latch release button. You are actually just pulling the door open. That would be fine if they had used something besides plastic on the control panel cover where the handle is built into. The control panel is only held together with plastic pieces that the screws go into. After only a couple of years of pulling on this the plastic parts holding the screws have all broken causing my control panel to just flash. My husband is a maintenance engineer and upon taking the screws out couldnt believe with such a high quality machine that they had used plastic in the main place where they needed strength. The wiring was cut so short to the control panel that one of the plugs had come undone when the cover began separating. I only need the plastic cover because my control panel is working fine but of course you have to buy the entire control unit which is $150.I purchased Maytag because I thought they represented a reputable American company but I was very wrong. When I contacted Maytag about the problem they were very unconcerned and just gave me a link where I could purchase the part. When I told them it would be my last Maytag product they didnt even have a comment. Giving Made in America a bad name.

Purchased 4-2010, used maybe once a week, it stopped working 11-2013. They sent someone out to replace the faulty recall, which the recall says there is an electrical wiring failure that can cause a fire, so they replaced part. It did nothing, the dishwasher still would not wash, just fill up with water and drain, but would never go into wash, so we call and argue. First girl said that recall has been known to burn out the control panel so we have to pay for a service person to come out and diagnose it, if that is it, they will pay to repair it. Then when he does diagnose it, we call back, the next person says no, the recall has nothing to do with the control panel, that it is just a bracket that holds up the heating element... REALLY. Well then the Consumer Protection Agency has the wrong info because I just looked on there and the recall says, Electrical failure with the heating element that is not related to a bracket, I can read and I am not stupid, so we were out the $50 service call, so we finally got them to agree and pay for the part, but we would have to pay to put it on...HHHHHH NO, I am not spending another dime on service calls, I could spend the same amount and go and get a scratch and dent dishwasher for the same or just a little more. We are calling back tomorrow to argue more with them, then I am emailing the local TV station that handles these kind of issues. MAYTAG is a piece of nothing, I will never buy this or anything with their name on it again....

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

Maytag centennial washing machine - I am pretty good as a mechanic or this machine would sit unused. Purchased in 2/15 at lowes. Poor installation. Then the machine... I hooked it up properly and ran it with extra load setting to see the machine develop a life all its own. The sheet metal breathed in and out like the chest of an old man running uphill. Lower exit hose not properly installed leaked on floor so I put on a new adjustable clip. Machine can only handle small loads. While it does wash clothes (it is a washing machine!) it requires close supervision in size of load. The machine needs a plumbing bang pressure gauge or you are likely to blow out your water pipes. It sounds like there are a bunch of people walking the machine with ball peen hammers. Who cares, but they were made in America and moved to Mexico. They should need visas to get back in. Absolute junk.

I have always heard Maytag was one of the best so after replacing too many washers to count in 15 years, like Whirlpool and Kenmore, I decided to spend more for quality. I figured pay a few hundred more once rather than spending $400 for a cheaper one that only lasts 3 or 4 years. That choice seemed environmentally responsible and financially as well. However, I couldnt have been more wrong. In 2016 I purchased the Maytag Centennial top loader for $500. I really loved the size of the tub and the way it looked. I can fit a large comforter in it with plenty of room leftover. I also have no interest in a front loader after reading reviews. So I thought this was going to be great! Well it hasnt been. It has broken 3 times. The circuit board twice and now the bearings are going out in the motor. I fixed it the first two times but now Im done. Im done with Maytag, Aka Whirlpool. I think it will be a Speed Queen for me now. Im hoping it wont be a dud also because they are pricey! It actually scares me to spend that kind of money. I have really lost my faith in most companies nowadays. Customer service and quality has gone out the window. I think about how much this impacts the environment! Its terrible that appliances only last a few years before they end up in the landfill.

First things first, Maytag Bravos washers are crap. Dont buy one. Purchased model # MVWB750WQ 06/12/2010 for $872.02 + tax. After 3.25 years the spin cycle started making extremely loud whining noises. Bought a replacement water pump for about $100 as several people were reporting the same issue. Before I had a chance to replace it the washer started leaking from under the washer. And not a small amount of water! Mats were getting soaked after each wash. I went ahead and replaced the water pump. But the whining noise, while diminished, didnt go away. And the leak continued. Based on what Ive read on this and other forums it looks like Ill have to replace the bearings for the tub. Not going to happen. Just ordered a Speed Queen washer for about the same price as the Maytag and I will never buy another Maytag (or Whirlpool) product again. Note that I purchased the Maytag at Best Buy. Its important that Best Buy take some of the credit for this issue as they are complicit in keeping these substandard products on the market.

I just bought my first home and after well over 20 years of apartment living and not having my own washer & dryer I was so excited to finally be able to buy one! I decided on the Maytag/Bravos and even spent the extra $100 for the glass top. The high efficiency machine was delivered on August 8, 2016. My kids are grown so its just me; I do one load a week give or take. A week or so ago, I noticed the washer was taking an inordinate amount of time to go from sensing to washing and even longer to get into the washing cycle. This past weekend, it didnt work at all. Just sat for hours with the sensing and washing lights on, without actually washing the clothes. The machine was packed loosely with the correct amount of High Efficiency Detergent in the proper place. I called the #Sears store I purchased the appliance from (Braintree Ma.) and they said there was nothing they could do as it was past 30 days, gave me their customer solutions number which is basically a call center with people who I could barely hear and/or understand. They in turn gave me more phone numbers which seemed to me to be in the same call center. I want to return the 4 month old washing machine that doesnt work and I want my money back. Ive filed a report with the Massachusetts Attorney General Consumer Affairs Department. I will NEVER AGAIN shop at #Sears and I will NEVER AGAIN purchase a #Maytag appliance. I am beyond disappointed in #Sears and #Maytag, both names that used to mean quality and customer service. And if theres a class action lawsuit to be filed, please count me in.

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

We bought a Maytag Dishwasher - Model #MDB4949SHW a year and a half ago at a Home Depot Location. We had previously had a Whirlpool dishwasher for 13 years of heavy use, with no issues or difficulties. At the time we purchased our dishwasher, there were various different brands on sale, including the one we purchased. The sales rep at Home Depot advised us that although we could get a similar dishwasher for the same price, that this particular model had a 10 year warranty. When I heard that, all I heard was 10 worry free years. MY MISTAKE. I could never have imagined that a company such as Whirlpool would advertise a warranty, that in the end is made up of nothing but false advertising.We ran a cycle during the Christmas holidays, and detected a funny smell of burnt rubber but didnt know what to make of it. I googled the issue and some people had had experiences with perhaps a plastic utensil or some other plastic, being burned by the heating element, so I figured that its what might have happened. I ran another cycle the next day, and the smell was much less prominent so I thought the problem had gone away. The next time we ran a cycle, the water didnt drain. We called in a repair person, and was shocked to learn that both the drain pump and main control board needed replacing.We got in touch with Whirlpool and low and behold, the only items they cover are nonsense items such as the racks, drum, tub...etc....in other words, the parts that are actually responsible for the running of the machine, are not covered, neither is LABOUR. Therefore, in my opinion, their warranty is trash and should not be relied upon under any circumstances. We purchased a new dishwasher just a year and a half ago, and are left with a heap of junk in our kitchen. Our options? Either spend $600.00 to $700.00 on repairs, possibly more, or buy a new dishwasher. When I asked if there was anything they could do to at least mitigate my damages, I was told....Sorry for your inconvenience...but do you have any other questions. I dont have any other questions...but I do have have a comment.... Make your products better....and dont print warranties that are utterly rubbish, false, and only serve to mislead the consumer. Needless to say, we will not be buying any more appliances from this company. Their one and only goal is profit for their shareholders with no regard whatsoever for the consumer. If I could give it ZERO stars, I most certainly would. :)

I purchased a Maytag model # MRT 18 FFFHO1 refrigerator from Home Depot. After 7 months, it stopped cooling (wouldnt cool below 52 degrees). Fortunately, I had taken out a 5-year extended warranty. Thats the good news. The bad news is that after numerous trips by a certified repair man -- and three spring/summer months without reliable refrigeration -- Home Depot promised a refund. Well see.Bottom line: keep looking for a refrigerator that works. I have tried GE, Frigidaire, Maytag and Sanyo. Since many of these companies are really just one inept cooperation with more names than Frank Abagnale (Catch Me If You Can), let the buyer beware! I would give Home Depot protection plan 5 stars, though. They stayed with me through thick and thin: by emails, phone calls and text messages. However, their protection plan is worth more than Home Depots appliance products -- through no fault of theirs.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

This a 28-month-old bottom freezer fridge purchased from Home Depot. At about 26 months, the freezer started to leak water as ice was completely covering the bottom of the freezer floor and the excess water would then run out once the door was opened. I managed to get the ice out with slim bladed putty knife and did this about every 10 days. Contact with Maytag affirmed that I had no warranty available as it only comes with a 1-year, except for the compressor. Every effort was made to sell me an extended 1-year warranty for $330, and then a technician would be sent to fix the problem. I asked if the compressor had failed, would I be discounted as it is warranted and the answer was no, the fee was still $330. I had great difficulty in explaining why I would purchase a warranty for an item that is already warranted to no avail.I decided to go with their 2nd option of having a local appliance tech to solve the problem at my expense which I did for a final cost of $130. Technician came and immediately knew the problem and removed a little black rubber stopper valve that is supposed to let water pass but gets clogged and the water backs up into the freezer. It took him all of a half hour to fix everything, $85 for the visit and $45 for time in place, $0 for parts. He stated that this is a continuing problem that he has seen many times. Moral: Dont buy any Maytag products as the Maytag repairman who had nothing to do has died.

We bought the washer less than a year ago. The washer became off balance with an average load of jeans. The washer shook so violently that it cut our floor, busted our wall, and broke itself. Water covered our floor! We have now been over a month with no washing machine (still paying on it, by the way). We have had to pay to get our clothes washed in the last month = EXPENSIVE! The repair company has been out to our home twice, broken high-quality tools trying to repair the machine, and told by their higher-ups that the washer can still be repaired. Customer service only tells us that we have a repair warranty and the first repair has no time limit.

I thought it was just my machine that sounded like an airplane taking off in my laundry room. Upon reading these reviews I see there is a real problem with this machine. My parents and grandparents trusted and swore by Maytag products. Maybe then, but certainly not now. Maytag for me stands for landfill. I have had 2 Maytag certified service companies come to repair my washer that is only 6 years old and its the same part both times which I am told by these service providers has been a problem and Maytag knows about it. But when I call Maytag all I get is some sound bite advising me there has been no recall and since I have an extended warranty I will have to take it up with them since that is who my contract is with. Of course they are only obligated to make a repair and cannot replace a defective unit. Of course not.Far be it for Maytag to step up and really stand behind the promises they are making all over our television channels with the new Maytag man. The top of the washer is also all rusted out around the soap, bleach, and softener openings. It is a poorly made machine with known issues by a manufacturer that I will never buy from again. Its a sad day that manufacturers are not held accountable for inferior products and even sadder that this Maytag manufacturer boasts its made in the USA for this machine. So is it back to China we go??? If you want America back you better support your product to your buyers.

Same thing as everyone else. The motherboard/control board, the main face of the washer went out and this part isnt covered on an $800 commercial washer after only 3 years of residential use on a commercial washer. Menards refused to swap it out, saying this is Maytags issue. Maytag boasts their 10 year warranty and labels it right on the motherboard as a 10 year warranty, but the motherboard isnt covered? If the main computer isnt covered, What is covered? Just screws? I called Menards and got nowhere. Called Maytag and held for an hour then had to hang up so I can work. The warranty is extremely misleading and is the reason we bought this particular washer, because it says 10 year parts warranty right there, but Maytag conveniently doesnt consider the main control board a part.

Maytag MCT Washer & Dryer - I bought the largest capacity to save time. However even my 6ft tall husband has problems reaching the bottom to remove clothes. Even worse is the lack of water to clean clothes, washes so long it wears clothes and they are still dirty. I tried to improve on my old Neptune and Id love to have it back. I may have to junk this washer. The dryer is very slow. Buying this set was tossing my hard earned money in the trash.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I have had a Maytag Bravo Model MVWX500XW0. Bought less than 3 yrs ago for over $550. Four days ago, the drum would not turn during wash or spin. It would act like it was going to turn but then the door lock lid kept flashing. Today Maytag repairman came by and put in a new lock circuit. Instead of fixing the problem, it made it worse. The washer started making rapid clicking sounds and finally the lid lock stopped working altogether. The repairman could not get his computer to even do a diagnostic. Instead he calls his boss who says it must be the motherboard, a $300 part. My research indicates that Maytag almost always says replace motherboard and customers find that doesnt work either. Ive never had a washer last less than 10 years. Three years for a high-priced washer is mind boggling. Ive also never had a repairman make things worse by installing new part but that happened. I will never buy a Maytag product again, even if its owned by Whirlpool, which used to be a name you could count on.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

The soap dispenser along with the port it slides in becomes molded and is not easy to clean, front loader. I never had a front loader washer with this moldy problem. I have been cleaning it at least once a month,

I have a top load commercial tech washer with an agitator that is brand new as of September 2019. I have done all of the troubleshooting suggestions and nothing works. I use 1 tsp of liquid cold water detergent, deep fill, extra rinse, and clear liquid oxi and my darks still come out with white stains. I have had a Maytag tech check out the machine and it checks out without issues. I would never recommend this product to anyone!

I bought a Maytag washer about 4 months ago and the dryer the washing machine has went down a couple of times but I managed to get it to start again. This time it will not start back up. It just as a little water and stuff and will not lock and wash. It never gets the clothes clean and you have to wash them twice or at least a residue on the clothing. I hate this washer and Im very saddened that Maytag will not come out - told me that they had to find someone. There was no one in the area that could fix my washer. It has been nearly a week now and no response from them. Im going to have to buy another washer. I am so upset to spend nearly 800 some dollars on a brand new washing machine and it does not work. I think that was all the complaints that I have seen on this page so somebody needs to put them on the news and also someone needs to start a lawsuit against this company. Shame on you Maytag. Very unhappy with your product and you.

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.

I bought a Maytag refrigerator over the summer - the French door and drawer freezer. Expensive but crappy. After about a month motor starting making noise then is shut down. Called the store. They came and swapped it out and not even two weeks later same thing. Looked up product and all awful reviews. Never thought to look up reviews before purchasing. Could of save myself the headache. Not to mention my daughter was like, Mom stop buying that brand. It sucks. Did you not realize our washing machine is the same brand and after almost two years it started acting up and your last washing machine you had for 10 years before it even gave you any problems.

Bought a Maytag Washer, in 2010 the Bravo. Good looking washer and dryer. I bought a 4 yr warranty for both. My washer has needed service every yr of the warranty, leaks and has stopped running. Now it is out of warranty and it is leaking again. Was just fixed a little over a year ago. I am now seeing a lot of rust around the top of the washer. It has just about covered the one port where you put the bleach in. The seam around the top in the crease is full of rust. My dryer is fine, bought them both at the same time. I have never seen this on a washer before. My mom has had her Maytag for yrs no problem. I bought these thinking they would last, boy was I wrong.

Maytag topwasher 2011 model MVWB300WQ2, SERIAL C11271134 - Im from the old school, expecting to get my money worth. I purchased a Maytag Bravos automatic washer in 2011, now less than 5 years later, it has a very loud knocking noise during the draining and spin cycles.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

I bought a Maytag dishwasher in April 2012. The electronic control panel failed in October 2013. Repair quote was $250, and there is no guarantee that the new control panel will not suffer the same consequences. My research has revealed that this is a very common problem with the dishwasher experienced by a large amount of owners, all about at the 18-month mark. I contacted the company and was chastised for not purchasing the extended warranty and was basically told, Too bad so sad. Buyer beware, do your research before you purchase this appliance. I will never buy a Maytag appliance, or any brand associated with the Maytag name.

Purchased Maytag Bravos Washer in 2013. Used a little over a year and had to put it in storage for 2 years. Biggest piece of junk Ive ever had. Ive had cheap washers that lasted more than 20 years! Repairman said all diagnostics read normal. I put a very small load in to show him the water was not even wetting the clothes and only swishing them around a little. The shirt on top never got wet and was still in its same position when it went into the final spin. He said this is normal. He recommended I dump the machine and find an old NON Maytag model with the tall agitator!!! Ive tried using all the settings combinations; and the water level never gets all the clothes wet and clothes do not get clean. Will NEVER buy a Maytag product again.

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

We bought this washer in February of 2010. We had the pump replaced under warranty in January of 2011, and the pump appeared to have a hole in it from some type of hard object that had gotten inside the pump and damaged it. We then replaced the L-shaped hose between the tank and the pump because it had a small hole in it - very thin rubber. Last week, the washer was leaking again and the service technician said that the pump housing was cracked due to a penny rattling around inside the pump.This washer performs very well when it is working but it seems to be too fragile to handle on normal usage. The Whirlpool washer we replaced with this one ran for 23 years with no problems before it finally went out. From all appearances, it seems that every failure we have had with this washer has been due to damage from foreign objects getting trapped in the pump. Is there no screening mechanism to prevent hard objects from entering the pump? This seems to be a design flaw more than anything.

This is not a complaint but a love-letter. I know that todays Maytag Neptune is not the Maytag of old. But Im here to report that Im still using a Maytag washer that was built in 1982! The only thing wrong with my machine is that it occasionally goes off-balance when I wash heavy towels or blankets. Note: We inherited this machine with the purchase of a home in 1991. We were a family of 6, so this machine has done many heavy loads! Im looking forward to celebrating my Maytags 30th birthday, come Jan. 1, 2012. And I would love advice on how to replace it, eventually, with another machine that has just the basics - no bells and whistles, computerized control panels, etc.

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

After 9 months, the $850 Maytag Bravos started making extremely loud grinding noises during agitation cycle. We had 5 repair tech visits from A&E Repair, Maytags national repair vendor (and several cancellations + unscheduled visits by same). Each tech said a different part needed to be replaced requiring weeks of waiting for parts deliveries and getting huge boxes delivered to our office and dragging them home since my husband and I work for a living and are not home to accept large parcel deliveries. We had to unpack the washer basket in order to get it into our car and saw it was completely damaged. After 4 months of tech repair visits, using my home as a repair shop, forcing me to take days off from work and still no resolution to the problem, I was finally able to get Maytag to replace the machine. Our previous washer was original to our 25 year old house before it died. Unbelievably, the new Maytag has the very same problems and we are back on the same merry-go-round. This has become a part time job and super headache. I have never had such a horrible experience with a purchase or company. This is not a case of heavy usage either. We are ready to dump this machine! Do not buy a Maytag or affiliate product - Maytag is the worst!

Works quietly and efficiently and I love it! I dont even know its running and the dishes are sparkling clean when they come out. How could ask for anything more. I would always purchase this brand again. The reliability is another factor, I have had Maytag before.

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

Maytag Bravos Quiet Series 300 - Just DONT BUY this junk. We bought the washer and dryer set from Home Depot in 2011 and have had nothing but trouble with the washer. Three times small objects like dimes, pennies and nickels got past the agitator into the drain pump which has been replaced twice. Beneath the agitator we even found a few missing socks. Today after a visit to the Laundromat, we bought a Samsung with a 5 year extended warranty. If that doesnt work it will be an old fashioned Speed Queen next. We will never buy anything Maytag again and I hope to influence everyone we meet about them. I cant wait to throw it into the city landfill for recycle dog food cans.

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!

We have to rinse off any food particles before we wash or it may not wash off. So I use plastic wiper before we load. Only 2 of us so items may sit 3-4 days before we run our Maytag dishwasher.

On June 5th, my husband turn off the water to the house since we were going to be away for 4 days. Unfortunately, it was not completely turned off. When we left, the washing machine was OFF, with the door slightly cracked open (to allow for circulation). When we returned, there was water all over in our upstairs, plus water had gone down the walls to the lower level. We could not figure out how the water got into the washer since it was turned off. The insurance company asked that we call a repairman to find out what was wrong. Fortunately for the repairman and us, the machine continued to go on and on after the Curtis had checked it out (it pumped out for him but not for us) and turned it OFF. It jumped from cycle to cycle after he had turned it off. Obviously the control board did its own thing. Be aware-- it can happen!!

The middle piece of glass on my four-year-old gas oven shattered. It was not being used, but when I called Maytag, they told me that that was not covered because I did not have an extended warranty, and that I can purchase a new oven door and would have to pay the service person. I hope they go out of business. Maytag stinks, and everyone should know this.

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

In August of 2009, we had an opportunity to remodel our kitchen plus add new windows and doors. How exciting! SO we had put down new flooring in our kitchen that matched our oak cabinets and since we had a little money saved, we wanted to purchase new appliances to match. We purchased a Maytag side by side with ice and water in the door. It also had the fingerprint resistant stuff on the outside. It cost about $1300. You buy name brand so they will last a while but here we are November 12, 2014, 7 years later and the compressor goes out. If repaired, it will cost $8090 to fix. Why do I want another Maytag. I got a citation I bought in 1978 and it still runs. Hello Facebook, you will my next visitor.

Bought the washer last week. Balanced it per installation instructions. Washed several loads. The darn thing goes off balance almost routinely. Have rechecked the level on several occasions and found it LEVEL. Contacted Maytag. The lady I spoke with said to just use it and it will level itself out. So much for Maytag help! This will be the LAST Maytag product I buy.

I had a Maytag dishwasher (made by Whirlpool) that after 4 months of ordering wrong parts, parts arriving damaged, and parts that were re-engineered and did not match up, the dishwasher could not be fixed. The extended warranty people (AIG) promised me twice on a recorded telephone call that they would exchange my dishwasher, and after many many heated telephone conversations was given a 20 minute lecture on how the word exchange does not mean they will replace it. The frustration ultimately overtook my misspent loyalty in anything made by Whirlpool and I decided to accept the buyout of my extended warranty contract, at a loss of hundreds of dollars to me - well worth getting rid of that dishwasher and any further affiliation with Whirlpool corporation. Absolutely horrible customer service. Unbelievably god awful treatment. I dont know what happened to customer service at Whirlpool, but my dealing with them has convinced me that the term is an oxymoron at Whirlpool. Horrible horrible customer service. I have never been treated so poorly in my life. I truly dont know how they can still be in business if they treat their customers like they did me.

DO NOT PURCHASE UNLESS you want dirty clothes that smell.... Water level not correct, binding laundry together and replaced the same parts with cheap parts over and over... just wanted clean clothes in a no frills washer. NOT with this washer. Owned it 3 yrs and disliked it the first half washed load... $869.00 heap of junk.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

I purchased a new washer and dryer from Lowes a few months ago. I had my former washer and dryer for nearly 20 years and although the dryer started to have some issues, the washer worked wonderfully. To have a matching set, I decided to purchase both a new washer and dryer. I was told the Maytag Bravos XL model was the top of the line and could handle large loads. After just a few washes I realized this machine does not add enough water to get the top clothes wet and there is no agitator to pull the clothes into the water. I returned to Lowes and was told to use the deep water wash. I tried that and still had clothes coming out from the wash still dry and dirty. Unfortunately Lowes would not take the machines back and I was told to call Maytag. Maytag said there was nothing they could do except send out a technician for a service fee of $98 to help me determine if the machine is functioning correctly. I could not dislike a washer and dryer more! The dryer catches clothes on one of the screws inside and pulls fabric pieces out. This is in my opinion the worst washer dryer set I could imagine having. I will share my experience with as many people as I can to help others avoid making the costly mistake of purchasing a Maytag product. Maytag does not seem to care they have designed and sold a dysfunctional product!

3 years ago, we purchased all new Maytag appliances for our home. Within one year, we had issues with the top load refrigerator getting warm and the bottom load freezer getting extremely cold. After calling Maytag and getting horrible customer service (long wait on the phone, no supportive/suggestive advice, rude representative), we were given a phone number for a local Maytag repair man who charged $300 just to walk into the house.He was literally in and then out of our house within 10 minutes. His advice was to unplug and defrost the refrigerator for 24 hours. Thankfully, his suggestion worked, but should have been given to us as a troubleshooter by the representative on the phone with Maytag.We have had to unplug and defrost the refrigerator about every 3 weeks since. It has become very annoying and stressful. There is obviously a defect in the refrigerator that should be replaced by Maytag! I will never buy a Maytag product again.

Maytag Dishwasher with model number MDB6701AWS and Serial Number 41687985NJ.It does not clean dishes like it should. We tried every possible way to set control settings, and still the dishes come out dirty and spotted. Also, it doesnt dry like it should. We had a Kitchenaid before we moved and it worked great.

I am 86 years old and have happily owned Maytag washers for many years. I just recently purchased the front loading model for ease of access. After using it for sometime, I could not be more disappointed. The clothes come out smelly, stained and gray. I tried using affresh washer cleaner on hot setting and the tablet did not even dissolve. There is black mold growing and must be cleaned constantly. I am so sad that my favorite company has let us down. I cannot afford to buy another washer so I am stuck with this lemon!

Maytag top load washer. I dont understand why Maytag would make such a piece of crap. It takes so long to wash, that I can only wash a couple of loads a day. It doesnt fill. It doesnt get the clothes clean. My electric bill is higher. Its so noisy too. Never thought Maytag would make such garbage.

July 2018 I bought a new Maytag electric washer and dryer. After one mo. the enamel inside the dryer started come off in sheets. It was replaced with 2019 model which after 3 mos. wont come on unless you unplug it and plug it back in after using it. I am now waiting for Maytag to send a repairman to come look at it. Steer clear of Maytag front load electric dryers.

Friends, Romans, Countrymen, At first I was skeptical and I once thought that I was the only one whose wife complained about the terrible soap stains and un-rinsed clothes. And finally my rinse and spin cycle stopped spinning and rinsing! However, after reading several reviews and complaints about the famous Bravo X He washer by Maytag and taking into consideration that there are over 650 complaints, making mine # 651. I now find I have lost all skeptical-ability and feel that we all may be comrades in this venture of purchasing the new trademark of the trade-mark Maytag. As almost all of us say our previous experience with Maytag was great. My parents had a Maytag since I was knee-high to a grasshopper and we were a family of eight. First we had the one with the rubber rollers, that was a work of mechanical genius. I even remember getting my arm caught in the rollers. Then my dad bought the spin dry model and that lasted a good 20 years. When I say the Bravo X at Sears it looked like the state of the art washer. However, and unfortunately I will have to agree with all of you. It is a piece of scrap metal and Maytag will not recall or recognize their mistake and make good on a recall or something. The least they should do is give us an old machine that does wash and spin to replace the new one that is less than 2 years old and does not work. I sure hope this letter does not fall on blind eyes. I think we may even have a collective lawsuit.Sincerely Yours;Mr. Lost All Skeptability!

I purchased my washing machine in July 2020 and it was broken by November. It took months without a washer before the warranty finally replaced my machine. I had the second machine less than 6 months when the water pump went out on it. They told me it would be two weeks for the repairman to come out. In the meantime my clothes were locked in the washer half full of dirty water. They told me we would have to force the lock to retrieve the clothes so they would not mold. The repairman called, never showed up, just called to ask what was wrong. Told me he would order parts and I had to wait 21 days to see if they would be able to find them. Today is day 21. I called the warranty back and was told it would be escalated and someone would call me in 4 days with a resolution. In the meantime I have spent $60 a week doing laundry for my family of 6 at the laundromat for MONTHS. Out of the 18 months have dealt with Maytag, I have spent more than 6 months at the laundromat. When I asked to be reimbursed the money I have spent they offered me a free 6 month extended warranty or a fifty dollar gift card. This product is garbage! The customer service is garbage. Dont waste your money.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

We purchased washer at Sears 6 years ago. Have had same issues for 5 or more years. Sears has been out to check it 6 to 7 times! They clean it out, tell me to use (expensive) Affresh tablets monthly, problem solved but it never is! When we run our washer and walk in laundry room it smells like a sewer. If we open lid its even worse. I use Norwex all naturally, biodegradable laundry detergent. There is nothing Ive done to create this smell. Its a manufactured problem that probably relates to ALL the other issues with this crappie washer that Maytag will do nothing about. I called Sears for 7th or 8th time, said they could send someone out AGAIN, I said thats a waste of my time and yours. They told me to call Maytag. They wont do anything (warranty is up). Of course there are NO ISSUES OR RECALLS on this washer and obviously there should be with not ONE good review! Im angry. You all should be too. We paid good $ for a product that used to have a good name and they are screwing us. I think we should ban together with a class action lawsuit. Please give me your thoughts. They know something isnt right and they shouldnt get away with this.

I have called numerous times and the satisfaction is out the window. The MOLD is so bad on the gasket that I can not get it off and it just keeps getting worse. My clothes smell musty even after they are washed. Really fed up... I have had different Maytags for at least 40 years and I will not purchase another one at this point. Apparently your customer service is as bad as some of your machines. My word of mouth is not good advertising for you.

I wish I had researched high efficiency washers before buying because of a name we trusted implicitly. Our washer does not get our clothes clean & cleaning it with Affresh is not enough. I have never had to work so hard at getting clothes clean! Towels smell musty, stinky. My husbands sweaty workout & gardening clothes smell worse, even with subsequent washes & his shirts have white spots from the detergent not even being washed out. The rinse cycle water just washes out the bottom of the machine while the clothes are plastered against the side of the machine. I do not wash my husbands clothes with anyone elses or it all smells and if he washes them twice, they still have that odor that comes from being dank. Even if I stop the washer to arrange the clothes on the bottom so they will get rinsed properly (gotta wait two hours for a load to finish) I have bought every HE laundry detergent on the market, every odor remover, vinegar, baking soda, bleach. For a year Ive been chasing my tail to do the dance that I never had to do with a top loader agitator Maytag that we had for 7 years and never had to clean once, but used unscented detergent that got the worst smells and stains out without much thought. Even reviews that I read about their amended top loader with an agitator are not very good.

Bought this Maytag microwave mmv 4205ds March 2016. Have had open/close problems five times in 3 years. Unit replaced under warranty once. Now out of warranty. No need to mention inconveniences we’ve been through. Whirlpool-Maytag obviously have done nothing to correct this problem. I will never buy any of their product again. Wanted to give them ‘0’ stars but program won’t allow me.

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

I started hearing the Maytag Microwave MMV4203DW00 beeping this morning after breakfast. I had not used it since the night before to heat up soup in a Corning Ware bowl. Its doing that 5E thing and nothing on the control panel works. Ive unplugged it, waited, plugged it back in and the same thing. It starts off saying Select Clock and 5E and then stops on the 5E. I bought this in Aug. 2010 and it is vented out the wall. Of course, that doesnt work now. The metal rack has never been put in it. Im single and the only one who uses it and I dont use it very much either. And this model only got the one 40-watt regular bulb over the range - lousy. And it doesnt work now either. And the control panel lights up orange. Had I known that, I would have never bought it in the first place. Of course, the stupid orange 5E lights up. Im unplugging it for good. Its not worth fixing. Do not buy this microwave!

I purchased a new MVBW725BWO washer. The cycle use and guide chart is generic. It does not remotely match my model. I called customer service. No help. She told me to tell her what I am washing and she will tell me which cycle. Really? Every time I wash a load I need to call her/him? I am not a laundry rookie but this machine has many buttons and choices. I want to do the right thing. Too bad. I washed two blankets and continually get an UL (uneven load) indicator. I have rearranged these two blankets every way possibly and there is no clearing the message. I called Maytag. No help. She told me that I should either 1) unplug the appliance, or 2) trip the breaker. Are you kidding me? If I didnt like those ideas or find them useful, call back and she will dispatch a service technician. Laughable. I guess I can pull them out of the washer, drip water everywhere, hand wring them, and move on. What happen to the good old days?

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

We bought what was supposed to be the top of the line Maytag dishwasher as part of a kitchen remodel in 2011. Well tonight it has quit working for the 3rd time! I think this is the last straw for us! Tired of spending all this money having it fixed. We also bought a Maytag microwave at the same time that has been nothing but trouble from day 1, but not as bad as the dishwasher. I can promise you we will never buy another Maytag product ever. Heck at this point, I would not accept a free Maytag machine of any kind! Stay away from Maytag!! Just to be more specific, the first time the dishwasher quit it was the board and cost us half as much as the dishwasher. I see lots of mentions of boards going out early.

I purchased a Maytag Dishwasher (MDB7749) in 2012 and one day before my 1 year warranty was up, my start button on the control panel wouldnt work. I called P.C. Richard and they sent a repairman who fixed it. This was in June of 2013. Here I am now hand washing again 1 year and 4 months after the repair. I called P.C. Richard again and was told that all brands have their weak points and because I got it on sale in the first place, I should not feel angry.Now that I am reading the reviews from 5 years ago, I realize that P.C. Richard knew this was an issue and chose not to disclose it or stop selling it. I had my G.E. for 10+ years and will go back to one. As I have no money for another new one, I will try to learn to fix this one on You Tube.

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

I almost didnt write this review because it is just a repetitive representation of this machine. I AM SO DISAPPOINTED with this machine! I had a Neptune and after a few years, it started to spew oil onto the laundry WHILE it was washing! It ruined so much clothing before I figured out what was happening. Came to find out, it was a glitch with the machine that the company SUPPOSEDLY, sent out notices about but I never received. Now the Bravos X... Bought to replace the Neptune, as it was advertised to replace Front loaders. Would accommodate a KING SIZE COMFORTER with no problem... Got out of one problem to get into another!!!From the beginning, I wondered how does this machine get the clothes clean? How would it was a king size comforter? It doesnt agitate like the other top loaders. I figured it was a new top of the line kind of technology. My clothes started to tangle up really bad even though I was not filling the machine over excessively. The clothes were staying dripping wet over and over again. It doesnt matter how much clothing is being washed, they stay super wet. I have to go through the Drain & Spin cycle to finish the cycle. IT GETS OLD!!!! I HATE THIS MACHINE!!!! Doing laundry is a HORRIFIC CHORE for me. This machine is TERRIBLE. NEEDLESS TO SAY, I CANNOT WASH ANY SIZE COMFORTER!!!After reading all these reviews, seeing how Im NOT the only one who is going through all these problems with this machine, I refuse to call any repair company! I wont spend another penny on this monster!!!! I WILL NEVER BUY ANOTHER MAYTAG ANYTHING AGAIN!!! Reason for this review... So anyone who is considering buying a Bravos X washer, think again. Hopefully you are doing your homework and will not make the same mistake we did!!!! Thank you for your time and attention to this matter.

The glass shelves stop 2 1/2 inches from the back of the refrigerator. Things keep falling down in back. I have a counter depth. Cant afford to lose any space. Freezer poorly designed for space compared to one I had before.

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

MDBH979SAM0 - Same old. Buttons not working. Control panel out. Repair cost total to be the same as the cost of the dishwasher. Its been over a year since we have extended warranty. Purchased from Home Depot. I am filing a complaint with the Consumer fraud unit of Washington State to get a State Action pursued on this.