The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

My Bravo washer does NOT clean my clothes. I have tried many detergents. I have to pre-treat all spots with dish soap and run hot water over and then rub the spots out. This was the only recommendation given after consulting with Maytag. I have to pre-soak my clothes in a pail of water with detergent. The water is brown. My clothes are dingy, spotted and have bleach spots. I am very careful so this is not from pouring into the bleach dispenser. Maytag was the reason I purchased this washer. Never again.

I purchased a Top Loading Maytag January 2019 (High Efficiency Washer) and I have had problems with it every time I do laundry. It doesnt matter what cycle I have it on. It doesnt fill properly when I put it on deep full. It tangles my clothes so I have to untwist them when I take them out. It has torn some of my things due to twisting. Some areas of the clothes dont even get wet. Some areas also do not get rinsed properly and I have to repeat the cycle. I have had repair people come out and they cant find anything wrong. I am so unhappy with the washing machine and Maytag just ignores the issues I am having. Im going to have to give it away and get some other brand. I am just devastated that I spent all of this money and clothes are getting ruined.

Bravos gas dryer - three issues in three years. Same issue twice, clothes are not drying. Now I have company coming and have to deal with his issue. The blower motor went. So, I have paid for a new dryer in repairs already. The washer is making such a loud noise when it goes into spin cycle that you have to turn the volume up to the highest level on the TV and it is still tough to hear. It’s unbelievably in the horrible quality. Make the product and parts in the USA and stop buying junk from China and Mexico. This is good American money that is flushed down the toilet with Maytag as well as your reputation. Fix your quality control and do the right thing!

I have had may BravosXL washing machine for 5 years and it is now sitting on the porch waiting to go to the landfill. It has not worked properly since day one, did not clean the clothes properly and even left dry spots where the fabric didnt get washed. Approximately 6 months ago it started making a loud noise while spinning. This week it literally exploded and there was water and oil everywhere, lifting the floor in the laundry room. I am shocked that Maytag would attach their name to such a poor product.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

After only 4 years, this washer stopped spinning. Called Maytag support (Ha! the ads show the Maytag repairman sitting by a non-ringing phone) I had to wait 20 mins to get through. Only after paying for a service call would they be able to determine if this problem was motor-related. In reading reviews (which in hindsight I wish I would have done prior to purchasing) this is a common problem and is related to bearings going bad. Pay for service call vs buying a non-Maytag product -- will set this out by the curb and buy a different brand.

In December 2017 I bought a Maytag Bravos (w/o agitator) based solely on past experience (56 yrs.) of buying from Maytag without any complaints. A friend told me I wouldnt be happy with my purchase and she was RIGHT! It doesnt get my clothes clean to my satisfaction, my towels are all getting snags as well as silky sheets and pillowcases and dark clothes have a soap scum line on them. I have slightly better luck if I wash everything with the deep water level option but I still need to wash dark clothes a second time without any soap or fabric softener to lighten the scum line.I am very careful to use minimal amounts of high efficiency detergent but that doesnt help. I called Maytag and complained within the first month but then we were gone for the month of February and I just never followed up with them. Now Im sure its too late to do anything. I wish I had listened to my friend. Hopefully I can save another consumer from making the same mistake I made.

Purchased Maytag dishwasher two years ago from Home Depot. It worked for about six months before it would stop working. When adding a dish after initial start would cause the unit to just die. After unplugging unit for a day the start/cancel drain buttons will flash. After reading online about a demo mode have tried and gotten it to work periodically. I continue to read online and have found there is a diagnostic mode. The settings are in a schematic packed with the unit. I found mine written in French (part #W10321879A). I called Maytag/Whirlpool and asked for the English version. They could not and would not provide me with part #W10321878A the English version, a single sheet of paper. They will only provide to a licensed repair technician. I am only asking for what should have been included in the original purchase. I paid $850 for a dishwasher that is not chump change. I know the control panel is bad but I would like to use it until the new part arrives. I think I may return the control panel and take my losses and go buy a brand that is not owned by Cesspool (Whirlpool).

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

My fairly new Maytag dishwasher took a break and stopped working. No lights on the control panel although there was power to the appliance. First repair call, I needed a new computer board. Then when the part arrived and was replaced, no lights on the control panel! Fuse checked out ok and now waiting for a control panel replacement. Really??? Dependable Maytag? No way and never again to purchase from this company (Whirlpool).

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

I purchased the Maytag Bravos XL washing machine because I wanted a top loader that was water saving. This washer boasts of a 10 year commercial capacity so I thought I was buying a decent machine. Unfortunately I have had a very disappointing experience. From the start this machine has not cleaned clothes properly. We circle clothes around the agitator and only fill the machine a third of the way full. This is the only way to ensure clean clothes. We use HE soap.As if this hasn’t been bad enough, the entire motherboard seems to be glitching out. It throws a different code each load and sometimes won’t start. Other times it won’t stop. It isn’t safe to use when we aren’t home or are asleep, making the time delay feature useless. Last night the machine ran for 2.5 hrs on a 1hr 30 min estimated deep water wash. I finally turned off the power and let it drain out after it insisted it had 45 min for the last hour.... this thing is a total waste of money. Will never buy another Maytag!!!!

I had one set of Maytag washer and dryer and I loved it. I bought another set and hate it. The washer smells and has been fixed a couple of times and the dryer is bad. I had to have a drum replaced because of one of the bars inside. I paid for the insurance but the bar was considered cosmetic. It has fallen off again after about 2 years and Im sick of it. I will never buy another Maytag again. Repairman, of course, had to order the drum and then I had to take another day off work to be here when it was delivered and one more to wait for him to come. I am so unhappy with this brand - never again.

I bought a Maytag dishwasher less than two years ago. The Maytag repairman just informed me that the control panel, the control board and the harness were burnt and needed to be replaced with parts costing over $300. I said, No, thanks. I paid him the $99 service call fee and called Maytag to see if they would help. Nope, they pretty much said, tough luck.

I bought my Maytag about 3 years ago. Have had continuous problems and now the whole barrel has broke and dropped down. I was treated with disrespect from the repair man and will never buy another Maytag washer.

Bravos mct. Unbelievable, this washing machine is terrible, no water. The water level doesnt even cover 6 items. Have to wash triple the loads of my old washer just to get the clothes clean. I have to go to the laundromat twice a month. I shouldnt have to do that. Almost want to fill the washer with water, but dont know what will happen. Very unsatisfied with this washer.

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

I purchased a Maytag dishwasher in 2013 and the control panel needed replaced within the warranty period. About a year later, the control panel started to malfunction again, this time out of warranty and Im told it will cost over $350 to repair. I paid a lot for this dishwasher and thought I would get years of use out of it. I plan on buying a new cheaper one (not Maytag) for a little more that the cost to repair the Maytag. Im very disappointed and will not purchase another Maytag. I also read online that Im not the only one experiencing this problem.

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!

My dishwasher just stopped working 1 year after purchase. Apparently a control panel issue. I have sold Maytag appliances for over 10 years and this is the thanks I get Maytag... Unreal. I wont buy a Maytag, Amana, Whirlpool, Jenn-Air, KitchenAid, etc.

My husband and I bought this refrigerator on 11/24/17 at Lowes for $2969.00 (excluding tax and white glove delivery). Never thought that not even after less than 2 years we would be having so many issues with this unit. The fridge part stopped cooling a couple of months ago and we were told by a technician that it was due to some coolant issue which of course our home warranty (Choice Home Warranty) wouldnt cover the repair. Well my husband fought them and we were able to have a second technician come and told us it was a sensor issue which he replaced. In the meantime I called Maytag to complain and they wouldnt even send someone to take a look. Anyway, the fridge worked after they replaced the sensor but unfortunately last week we started having the same issue. You would think for such a price you would get a decent unit, but big mistake there...now we have to find a way to replace it and we have little kids in the house. I also find out that Lowes doesnt even carry that brand anymore, perhaps because its defective. Maytag doesnt want to help us and Lowes cant do anything about it. So please STAY AWAY!!!! Should we be compensated, yes I believe so and so does anyone going through the same issue. Money doesnt grow on trees, stop deceiving your consumers Maytag!

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

Weve always bought Maytag, but this is our last time. The washer is just a piece of junk. It uses very little water and the agitator does not work. The clothes end up at the bottom in a ball. The water level is so low sometimes my clothes arent even wet. As I type this it has been stuck in the rinse cycle for 2 hours. It just keeps repeating. Maytag should have to replace everyone of the BRAVOS XL washers. I am no longer a loyal customer. I might as well go down to the river and beat my clothes on a rock. At least they would be cleaner. Shame on you Maytag!!!

Purchased a Maytag front loader and matching dryer in Sears and have had nothing but problems with both since the beginning. Now that the warranty has run out we have even more problems and doing laundry has become stressful. Big lemons. Wish I had kept my Kenmore units. Now looking into reviews for other brands, may go back to the Kenmore brand too. NOTHING can be as bad as Maytag.

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

I have had nothing except trouble with my new Maytag Bravos washer! I first had a suspension arm or something like that replaced along with the agitator. My water cycle has never worked correctly since it was new. I take out the clothes and half are still dry. My daughter washed her kids’ clothes in the washer while she was living with us and the stains did not come out. She thought that is really unusual since they werent stains that normally you would see left on the clothes. I went to my father-in-law’s house (they have a front loading Bosch), took her detergent with her that she used here and guess what? It’s just one washing and the stain was gone. She had washed the clothes in our washer at least 7 times trying to get out the stain. Now, we have such a loud noise that it sounds like it is going to take off. Then, the bottom of the washer started to leak. We took it out and checked it and we cant find the leak. The clothes smell awful when they come out of the wash. I dont know if it is bacteria build up. I use the cycle cleaner when I am supposed to. This is so sad. This is the first time I have had matching washer and dryer and I wish I would have kept my old Sears model that worked great. I havent decided if we want to fix it. With the price to fix it, I can buy one I might like. Never will I buy Maytag again or another Whirlpool without checking out the reports.

I am absolutely disgusted with this Maytag Bravos XL washer. Have owned it 6 months and cant wait to get rid of it. We live on a farm and have cattle. If jeans go in the machine with mud on them, they will come out with mud on them. I have tried soak, deep water wash, power wash. Nothing works. I might as well put a wash tub in my back yard and wash by hand. Anything black must be washed by itself as it will come out covered in lint. How did this machine ever go on the market? Expensive mistake. Please do not buy this machine.

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

I purchased a Maytag Front-Loading Washing machine. It was purchased on 11/30/15. Approximately this January, 2017 the spin cycle stopped getting all the water out of the laundry. Towels came out wet, shirts came out wet and I tried washing a small bathroom rug that came out of the washer dripping with water. My husband called Maytag to tell them about this issue. They told him I didnt know how to load the washer machine. Wow, I have only been using washing machines for 45 years and now I dont know how to load a machine. Then they said they will send him a video to watch on how to load a washing machine. I watched it. I wasnt doing anything incorrectly. (Maybe someone should send them a video on how to build a proper washing machine.) I previously had a Maytag Neptune machine that lasted twenty years until there was a class action suit against the machine. The clothes came out fine from that machine. I just purchased an Electrolux front loader that works beautifully. Now I have a Maytag machine that is nothing but a piece of junk in my opinion. It cost $824.21. I will never buy a Maytag machine EVER. MHW7100DW.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

I bought a Bravo XL Washer 3 yrs ago for $900 to $1000. The washer started beeping and not starting to eventually not turning on. I called customer service as I was told my washer was still under warranty. They scheduled a service man to come out with a $95 charge to come out. He came and it is the user interface. Apparently, this is a huge issue with this type of washer. He told me it would be cheaper to get a new washer than to have this one fixed. I called Whirlpool/Maytag after the fact and was told the part is $422.49 to fix the washer. I explained that I was told it was still under warranty and they denied this is the case. My previous washer I had for 18 years and not problems until the end. Having a washer for 3 years and being told to purchase another one because it would be too expensive to fix the current one is very disheartening! I do not recommend this product to anyone, nor do I recommend the company as they do not try to make things right or offer any assistance in any way! Buyer Beware.

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

I bought the dryer (Maytag Gas Bravo Dryer) from Home depot in December of 2010. The thermostat went out in July of 2011 and has replaced the same part 5 times up until August of 2011. Then they put a new burner with a thermostat and it lasted till June 1 of 2012. Now the warranty is out, they want me to repair this piece of **. I will never buy a Maytag product again.

I purchased this Atlantis dryer several years ago. To this day, I have replaced the rollers and drum three times. What a piece of junk! This will be the last Maytag I ever own.

We bought a Maytag Neptune Washer and from day one in 7/10/2004, we have had trouble with the washer and Sears. First, it stopped working within eight months after we paid over 1300 for washer and master protection agreement. We called over and over from that day and was told we didnt show in their system as owning one and that we didnt get the master protection agreement. This went on and on until they finally told us on 8/2010 that they finally did find us in the system and that the agreement had ended a year before and would send someone (that was on 8/31/10) to do the washer. After having sat for almost six years, it reset itself and worked that day. I told the guy from A&E that it was the computer but that wasnt what he replaced so the washer went right back on in a month. So we had to save to have someone else come out from A&E to charge us 143.10 to say it would cost a total of 310.51 for the computer and that it probably wouldnt work for too long.

This was purchased 3/25/2010 with the Home Depot Service Contract thru 3/2015 . We have already had a service call in 2013. We were OK until January 2015. Now we join many other customers with the leaking defroster. We have taken all the steps of the other customers. We went and called for a service appointment. Weve spoken to Maytag Customer Service 800-253-1301. Ive asked if there was recall? NO! I asked if there was log made of my call, NO! Any work done had to with Maytag Authorized Repair Person. The Home Depot Contract use a Non-Authorized Service Person. Weve gone to Home Depot. We are in a catch 22! We have spent good money on this refrigerator. Out of sight, out of mind. We will go back to Home Depot Again!

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

Bought a Maytag front load washer and dryer, it rattled and shook from day 1, they have come out 3 times in 1 month to fix that, now it wont even spin. This will be the 4th day of work I have had to miss, and all they say is, We have to send someone out to repair. Sorry. Do not purchase their products!! They dont care.

We purchased a front-load Maytag washing machine (Model MHW3505FW1) two years ago this month. When the machine is empty, we always leave to door open. We dont allow clothes to stay in it for long, never for more than a day (the load is usually changed as soon as the cycle is over). Right now, the rubber seal on the front has tons of black mold on it, and when I lift the seal to look underneath, its way worse. There have been many problems like this reported on front-loaders. Wish Id known! Maytag will not send a replacement seal.

Front load washer. When load is done. Removing is one long string of clothes... Is a large load washer which I like. But you cannot add any items after you close the door. And you always forget something that needs washing.

I called customer service to ask if there was some way that Maytag could assist me with repair of this like new dishwasher. When I said it was out of warranty and I had no additional warranty, I was told that a repairman could come out for $110 and diagnose the problem and that parts and labor would be extra. I explained that I had purchased Maytag because I saw commercials, for years, showing that Maytag repairmen had no work. She was very unhelpful and kept droning the same mantra, that a repairman could come out for the above charge. I was very angry and asked for the name and address of the President of Maytag so I could send a letter of complaint. I composed a letter, however: it is Thanksgiving time and I need my dishwasher so I made an appointment to have it repaired. I was told he would be out Mon. between 8 and 5. I asked for a more specific time and was told that I would get a call on Sat. with the time. Thankfully, no call came, because on Sunday, I read the reviews on this site and realized that Maytag was no longer a reliable nor a responsible company and I decided to save myself money and time and stress and just go out and buy a GE. So we will hand wash the dishes on Thanksgiving and buy a GE on Black Friday. This does not mean that I am letting Maytag off the hook. I intend to send my letter to Jeff Fettig at Maytag and also join in the class action suit. How very sad that the name Maytag has become just a name used to shill for defective and shoddy merchandise.

We purchased a Maytag MDB7749SBWO Maytag dishwasher. Suddenly the control panel does not work. Trying to find out why I found that there are thousands of complaints about this known defect with water and steam getting in and corroding the control panel. Shame on Maytag for continuing to sell these without fixing the problem. I expected my dishwasher to last many years based on the Maytag reputation instead I need to replace it. I am not going to spend the money on a repair with a machine that will have the same problem again according to other consumers.

We love our Maytag Dishwasher! It's very durable, doesn't use a lot of water and really gets our dishes exceptionally clean. The best part is that it sterilizes on the final cycle! We've long trusted any Maytag appliance in our families for generations.

The last Maytag washer was great, the dryer not so much, but I was able to repair it. This Bravos is sorry. 4 years old and the tube goes bad is not what you would expect from Maytag. Consequences, no more Maytag or GE for that matter, that dont leave many brands to choose from.

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

I purchased a new Maytag top loader at Home Depot. They delivered and set up. From the first load, I have had problems with the washer stopping and jerking. Clothing becomes a tangled mess. I contacted Maytag, they suggested I make sure I put on proper setting for the items within the washer. I do not know how one can fail at putting sheets in the washer and putting the setting on sheets and they are so twisted you have to spend time pulling them apart. This happens to almost everything I wash. I believe that I have a lemon, still under warranty, Maytag believes I should pay for a house call. Home Depot will only forward the information to me that Maytag gives to them.

This has nothing to do with the vendor. This is clearly shoddy workmanship on the part of Maytag. I bought this refrigerator in 2005 and already the compressor is gone. So therefore, I have to replace the whole unit.What kind of ** is this? You mean to tell me that you people cant find someone to build a compressor that holds up more than a few years? Why dont you try American made and built.I am disillusioned by the whole industry. Im sure the people at the top could care less.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

I bought this washer (Bravos Washer Model MVWX655DW) in June 2017. My wife and I did plenty of research and only complaint at that time was that it made load clicking noises. We bought it and it worked fine but never really filled with water to a level which would cover the clothes. Today I ran a load and brownish water was seeping out from underneath. When I lifted the machine my floor was covered with old stains which looked like oil or grease. I called a local service company and when they found out which model I had they refused to look at it. They said that particular model was known for having issues and when they fixed it, something else would go. They recommended looking online for reviews and calling Maytag.I did so and after explaining the situation to Maytag, they offered to send a technician to look at it to diagnose, not free of charge of course. While I cannot tell you avoid a particular company, I can say MY family will never buy Maytag again. If a washer is well known for having issues within its first 3 years and a company will not try to make it right simply because theres no recall on it I will spend my money elsewhere. Seems fishy that this machine has a ton of 1 star reviews within the last two months and Maytag does not want to eat the cost of servicing their junk.

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side

Maytag washer, top loader, Bravo series: We purchased Maytag washer and dryer 4 years ago. Last week, the washer started sounding like a 747 was landing in our laundry room. Maytag sent a service representative and informed us that the bearings were faulty and it would cost at least $800 to fix. It is appalling that a 4 year old appliance should fail like this. We will buy a different make and we will never buy any Maytag appliance again. This is such poor quality and worse service. Maytag would only offer a 30-40% off a washer, but only if we bought it directly from them. We can get a better offer from any local store. They also said we could get a discount on the part we need, but not the service. Do not, I repeat, do not buy Maytag anything. You will regret the purchase.

Thanks for the other reviews about the control panel problems... I too have the same issue with the short circuit. My Maytag dishwasher mdb7749sam1 was installed in January 2013. I spent an hour on the phone and the chat... HERES THE SOLUTION: When I told them the machine started in the middle of the night on its own, it became a safety issue. I have all the same problems as everyone else, flashing lights, the washer does not properly respond to the input from the control panel... I was told that even though it was out of warranty, as a gesture of goodwill Maytag is sending out an authorized repair service to fix whatever is wrong at no cost to me at all... Tells me that there really is an underlying issue. Anyway best of luck to anyone else in the same boat. I rated them as a 3 - not happy that this machine failed and I wont buy another, but they seemed to jump on fixing it...

We bought this range (model MER8700DS 1) March 25, 2015. Manual states when you use the oven first few times odor or smoke may happen and is normal. It also tells you this is not harmful but remove birds to another room because the fumes can kill them. Noxious fumes? Forget about the birds! Had to open up the whole house and go outside. Burned my eyes, throat and lungs. Day after day, repeatedly turned temp up to 400 trying to burn off what we thought might be a coating. No luck.Maytag got very concerned when I explained about the noxious fumes and had someone come out right away. Tech took it apart. He removed bottom (screwed in) plate that covers the bottom heating element. That plate gives the added ability to have 3 racks and make full use of the 6.3 cubic ft. capacity. Under the plate we found bits of insulation. We think that is what we smelt as it burnt up. He couldnt smell anything when he had it up to 400. So off he went thinking problem solved. Well, it still stinks. We will have Home Depot take it back. Oven takes forever to come to temp which we read in many complaints but thought thats minor. Dont know what oven to get instead since Whirlpool makes so many brand names. And other brands all seem to have their own problems.

Maytag, you are still trading on your good name but that will not last! I owned a Maytag, agitator style, for 20 years and it was still running just fine when we built a new house. I thought it would be wise to buy new appliances for my new laundry room so I chose the beautiful and expensive Maytag Bravos XL. I regret that decision. The washer lasted 4 years and began to have problems draining last week. The liquid that stayed in the washtub until the repairman could get here was so foul smelling! He came back today to replace the drain pump and now the washer is showing that the interface and CCU are not communicating. So now we are ordering another CCU and I hope this fixes the problem. I agree with all of you who say you will NEVER buy another Maytag again. Maytag, are you listening?

I have Control Panel issues with my Maytag Quiet Series 300 Dishwasher. I have saved myself hundreds of dollars! The problem occurs when oxidation or steam shorts out the ribbon on the control board. Simply shut off the power to your dishwasher. Open the 5 or 12 screws on the door. Open the black box where the Control Panel ribbon enters the Control Board, slide the white tension clasp away from ribbon and clean off ribbon using a paper towel. Re-insert ribbon and slide tensioner in place. Replace all parts and turn on power. Job done! I hope you have as much success as I did.

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

I made the mistake of buying the stainless steel bottom freezer (model# MBL2258XES1) approximately 1 year before the freezer started to make a periodic clunking sound. The repairman responded because my year warranty was still active and found no cause for the noise. Fast forward a couple of months later and it started pouring water out onto my hardwood floors!!! Unfortunately it happened while we were away and my floors were destroyed. Maytag wants nothing to do with me. Im so disgusted. I now have to have a towel permanently on my kitchen floor. Nice. I made the unfortunate mistake of buying an Amana dishwasher recently not knowing that they were also owned by Maytag. The dishwasher is a water waster :( This is very disappointing - you try and buy American and you get screwed. If any lawsuits start up, sign me up!!!

I bought the Washer and Dryer. All I can say about this washer is that it does not use water enough to be considered a commercial type of washer. Its balance is poor also for being so deep. I have to pour a bit of water on the clothes so the sensor thinks it’s a heavy load and do an extra rinse. And I saw that on a video regarding this washer trick. But I’m wasting more water cause I have to rearrange the clothes when done. I put the top ones on the bottom and start over. To me it’s a waste of effort sometimes I just go to the laundromat. They should consider their products if we all are complaining about this they should really do something. To me the washer is really useless.

I have filed a class action lawsuit against Whirlpool for their faulty control panels in their Whirlpool and Maytag dishwashers. Please contact my attorney, Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 and let them know if you own or owned a dishwasher with control panel failures.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

MY 8 year old LG front load washing machine died late in 2019. I bought a new front loading MAYTAG machine from a local big box store. It was delivered and set up for me. I had always thought Maytag was a well made product. I wanted to stay with the LG machine, however NO local Repair Service Companies would service it! I was told LG and Samsung were substandard products. (My 9 year old LG clothes dryer is still in good condition).I am truly sorry to say the MAYTAG washer is dreadful. The door locks and cannot be opened the very second you touch the start button. There are fewer wash cycles to chose from. You can never tell if the clothes will spin or be soaked. The door needs to be left ajar and the interior wiped down at end of wash cycle. Etc.. I was ready to call the Store to return the machine - I should have - but I like store. The Maytag price was almost $900. I am very dissatisfied.

As others have stated, cant wash more than a couple towels or 2 pair of blue jeans. The washer is useless. Purchased Maytag for quality and received crappy worthless machine. Maytag should take returns and refund buyers money!

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

I purchased the Maytag Bravo Series in August 2010. Two weeks ago, I had to replace the idler pulley on the dryer which was no easy task. Now today I was washing a load of clothes only to walk into my utility room and find it flooded. This didnt even start out as a small leak so at least you would have a warning. On the spin cycle, the washer is making a clanging sound. These were not cheap models. I paid $1600 for the set. I will never buy another Maytag product especially after reading all the complaints that people have had about this series. Why hasnt something been done to protect the consumer? I did not purchase the extended warranty as I thought Maytag sold a good product. I owned another set of Maytags that were almost 30 years old when we got rid of them and did minimal repairs over the years. We are only a household of 3. It is not like these appliances are overloaded or abused. Its very disheartening. In this economy, most dont have money to just throw away and that is what I feel like I did!

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

This product has been a huge disappointment, from day one. It wrinkles and tears clothes beyond recognition. When I called Maytag to complain, they tried to up sell me a service contact. I explained that it works fine, as a shredder, but it is just a bad design and asked if Maytag had any recalls. He then told me if I purchase the service agreement and they cant fix it then they will refund the $$... ITS NOT BROKEN. It was crap when we got it home. Shame on me for not taking it right back to Best Buy. Someone needs to start a CLASS ACTION SUIT. I am sure they have duped many people into buying this shredding machine...

Same as everyone else, ice freezes up on the bottom and water runs out all over the floor, ruining my new floor. Whole kitchen was new including all appliances. Maytag is ruining my floors. Can find no drain pipes so not sure where the water is supposed to do. I think they forgot to install one. But I am getting pretty sick of seeing my floors ruined and stepping in water.

I bought a brand new Maytag bottom freezer fridge in May 2005. The first thing to go was the timing switch. I lost all contents of the fridge and freezer. The next to go was the compressor. Again, all the contents of the fridge and freezer were destroyed. This was after the 5 year warranty was complete. The cosat of repairs is around $800.00, which is the cost of a new fridge. I emailed someone from customer service, who replied how happy they are to hear from me, and how I can call anytime. I called customer service, and spoke to a supervisor. The fridge was built in the USA, but cannot tell me where the parts are from. No one seems to get, that I am disgusted that an appliance would last only as long as the warranty lasts. Oh, and the repairs are only covered for 90 days. My parents have a 62 year old RCA chest freezer that is still going strong. The lesson is, dont get rid of your old appliances. They may use a lot of energy, but they last. I will never buy from Maytag, ever again.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

I just saw that there had been a class action lawsuit settled in 2005 for the Maytag Neptune front load washer and I was never notified as an owner! I have this crummy product and have been living with it for more than 10 years! I just scheduled a repairman to replace the moldy gasket (for the second time) and the noisy pump, and a latch that has to be slammed for a sum of $438. What a crock. I was told this was a top of the line model when I purchased it for $999. Ive never had such a piece of junk before in my life. I run loads of bleach weekly to control the mildew.

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

We purchased our Maytag Elite dryer almost a year ago. Began to have problems with it several weeks ago. We first tried to correct the problem through the store where we purchased it. After three failed service repair visits the technician recommended we call Maytag directly. We did. Another service appointment was set up. The repair guy determined there was nothing wrong with our dryer (?? It wasnt drying on one of the heat settings!!) but said he would come back and replace the front sensors anyway. After he left I called Maytag again. Explained why I was frustrated. I was told that since the repair guy said nothing was wrong with the dryer there was nothing further they could do for me. Further attempts at repair had to be at my expense. I was incredulous to say the least. The dryer doesnt function properly on the normal heat setting, but because the repair guy cant find the cause I am therefore just out of luck?I will never, ever purchase another Maytag product. I am shocked that they will not stand behind a product that is still under warranty. After only 11 months of use I am stuck with a dryer that will only dry on high heat?! How can a single service visit by their repair guy (whom is on their payroll) be the final say? No second opinion? Is he infallible? Simply unbelievable.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

I bought the Bravos glass top washer. It was always loud. I have a friend who had a cheaper model and his was loud too. My washer barely lasted two years before tearing up. It cost $85 to tell me it would be over $500 to fix it. I paid over $600 so it wasn’t worth fixing. Lid lock went out and gear went bad.

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

We purchased the Maytag over the range microwave December 2014. Three months after installing it the door cracked. Maytag did replace the door and the repairman thought it might be due to the heat from the stove (huh, it was designed to go over the stove, where there will be heat). Now, six months after that, the layers of plastic on the door are separating and the piece around the control panel is cracked. Maytag agreed to replace the control panel but refuse to replace the door as it is only cosmetic (their words). So much for paying a little extra for what we thought would be a quality product. It seems to me that if something was made to go over the stove, it should be made to withstand the heat.

For years I wanted a top loading Maytag washer. Last year I bought one at the cost of £720 plus VAT. Started using it last July and in November this year it broke down. The company I bought it from said, Sorry, youre out of our warranty... Really! Here’s some people who might fix it. Eventually Hotpoint took it on and honored a two year warranty. Since November I’ve had an engineer out twice. Still isn’t working. Won’t replace it because it’s now discontinued, so more parts ordered. Engineer advised me to go buy another washer. Thanks Maytag for totally disappointing me in what I thought would be my perfect washer. I will continue to email etc and hope that someone will help me. No point in phoning because no one listens. MY OPINION - DONT BUY AMERICAN PRODUCTS IN THE UK AS NO ONE CAN REPAIR THEM PROMPTLY IF AT ALL.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

I purchased the Maytag Bravos top load washer and the matching dryer at Home Depot back in 2009 after giving my son my very old Maytag washer and dryer that was running just fine. I liked the top load energy efficiency idea of the new Bravos and the large capacity of both the washer and dryer. Also, the Maytag name sold me, gave me confidence I was purchasing a quality product... WRONG. When it was delivered, there was damage to the dryer door, so a new one was ordered and mailed directly to me. Once it came in, I called to have someone come put it on. First issue, not a really big deal but disappointing.About one month into using the dryer, the top of it became so hot it could literally burn your hand. There was also an error message. I had purchased a one-year warranty, even though technically there is a manufacturers warranty on the product. A part had to be replaced in the panel. This happened twice. We then moved out of state for one year and the washer and dryer stayed in storage unused during that time.Fast forward to 2014 and the washer will not complete any cycle except the spin cycle. I keep getting an error message of OL which means overload. The machine is NOT overloaded. It literally takes me hours to get through one cycle of washing clothes. And they dont even come out clean. I called Maytag repair and they offered me a one-year warranty for $363.75 since the washer is having issues. They explained to me if its the control panel the cost alone for that is $383.00 not including labor. Also, the dryer take forever to dry. I have to run each load through a cycle twice to dry everything. So much for the energy efficiency of these machines. At this point, I am considering just buying another washer, something cheaper without all the fancy bells and whistles. I am terribly disappointed in Maytag.

Had the washer for less than 3 months just a week before the 90 warranty was up and it stopped spinning. Called service dept. What a joke for this company that keep yessing you. Took a week before someone came out. Said washer needed a new motherboard and they would only cover it once but there seems to be a ongoing issue with their motherboard. Had to wait over 2 1/2 weeks before they would have one in stock. The tech installed it however now when it spins seems she left the top loose.

Last year we replaced a Maytag dishwasher which had a faulty control panel after just a few years of light use (There are just the two of us). It was going to cost almost as much to repair it as to buy a new dishwasher, so we opted for an $800 model (MDB8959AWW6) with a control panel across the top of the door. There had been a recall on that first Maytag for the heating element or something, so we decided to put the credit towards a machine that would last us for years, we hoped!We have been in this house for 18 years and the original cheap builder-installed dishwasher lasted for 12 years. In fact, there was nothing wrong with it when we replaced it with the last one. Whatever happened to the lonely Maytag repair man? We did not buy an extended warranty, but I can see now that probably these things are only meant to last the lifetime of the warranty.We are semi-retired and cannot afford to have the dishwasher repaired, so it will be a decoration in the kitchen from on. Never ever will I recommend Maytag to anyone! One bad experience should have been enough, and we probably would not have bought a Maytag again had it not been for the credit we got for the product recall on the last one!

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

I purchased MVWB955FW (washer) and MEDB955FW (dryer) from AJ Madison and the units were delivered in December 2017. After using the washing machine 5 times the glass lid spontaneously shattered putting glass into the machine and all of the clothes. I called Maytag for a replacement/service and they had to reschedule as the lid wasnt in yet. A week later, I followed up with Customer Service only to find out that the replacement lid was also shattered. They didnt make a replacement lid without glass (not sure why you need to watch the clothes being washed). I was told that there were no replacement lids available anywhere. I asked about getting a replacement washer and was told couldnt do that.I asked them to pick up the units and refund my money, which they promised. It is now 2 months since the original call for service and I continue to have to follow-up with them (never get a call back) and STILL have the broken units in my house. I have since purchased a replacement set (LG) and waiting for my refund. I will NEVER do business with Maytag/Whirlpool again.